Schneider Electric TKS-5001, TKS-6001 Data Sheet

Page 1

GENERAL INFORMATION

For proportional temperature control, used with receiver-controllers. May be used with one or more calibrated gauges for continuous temperature indication at any local or remote position.

Specifications

Construction: Bimetal element, non-adjustable. Shipping Ambient Temperature Limits: -40 to 150 F (-40 to

65 C).

Air Connections:

TKS-5001, 5/32" dia. spring reinforced plastic tube. TKS-6001, barbed fitting for 5/32" plastic tube.

Air Consumption For Sizing Air Compressor:

.024 scfm (11.3 ml/s).

Air Capacity for Sizing Air Mains: 50 scim (13.7 ml/s). Supply Pressure (Indication Only): 20 psig (138 kPa)

nominal. 18 psig (124 kPa) minimum.

Maximum Safe Supply Pressure: 30 psig (207 kPa). Mounting Dimensions: Wall: 4-3/8" (111 mm) high x 2-3/4"

(70mm) wide x 1-5/8" (41 mm) deep.

Light Troffer: 3/8" (10 mm) x 3/8" (10 mm) x 3" (76 mm). Mounting Fittings: Order separately for type of wall

construction.

ACCESSORIES

Part Number Description

20-944 Restrictor tee, copper tubing, 1 SCFH. 21-038 Restrictor tee, polyethylene tubing, 1 SCFH. 21-153 In-line restrictor. AT-201 Copper bulb well. AT-203 Stainless steel bulb well. AT-208 Duct moun ing kit for TKS-40xx. AT-2 11 Bulb shield for wall mounting TKS-2031. AT-504 Plaster hole cover (small). AT-506 Pneumatic wall box fitting (two tubes) used for mtg.

AT-533-101 Adaptor 1/4 in. plastic to 5/32 in. plastic. AT-533-127 Adaptor 3/16 in. copper or 1/4 in. copper with 1/4 in. solder

AT-533-129 5/32 in. x 5/32 in. barbed brass connector. TOOL-100-500 Calibration panel

T-532-1

1-1-01 under cover of TKS-5001.

coupling (n

ot included) to 5/32 in. plastic.

TKS-5001 and TKS-6001

Pneumatic Temperature Transmitters—Room

General Instructions

TKS-5001

Transmitter is shipped with mounting screws and one inch copper tubes.

Range

on-A

Model No. Mounting

S-5001 Wall

TKS-6001

Order fittings separately for type of wall construction.

Light

Troff e

F ( C)

50 to 100 (10 to 38)

Span

dj.)

F ( C)

50 (28) Bimetal

Sensing Element

Descri

ption

Cover

Beige

Plas

N.A.

Ambient Temperature

tic

Limits

F ( C)

Shipping

0 to 150

-4 (-40 to

65)

Operating:

50 to 100 (10 to 38)

Connections

Air

5/32 in. dia. spring

orced pl

tube

astic

reinf

5/32 in. dia. spring

reinforced pl

Dimensions

H x W x D

in. (mm)

4-3/8 x 2-3/4 x 1-5/8

x 4 1 )

(111 x 7 0

3/8 x 3/8 x 3

(10 x 10 x 76)

PRE-INSTALLATION

Check the carton and device for signs of damage.

Page 2

Page 3

Mounting of TKS-5001 on AT-506 Wall Box Fitting Or Electrical Switchbox with Restrictor Tee Under The Cover (Requires AT-532-111-1-01 Kit - See Figure 4)

1. Remove cover.

2. Remove 5/32" tube on TKS-5001 from mounting plate.

Caution: Do not remove the end which is in the tube (connected to

sensing element).

3. Cut the tube and spring 2-1/2" (65 mm) from the tygon tubing.

4. Connect the tube to one side of the restrictor tee.

5. Connect the black tube to the main connection of the restrictor tee. Insert one spring into the tube. Cut off excess spring. Insert the black tube then through the large oblong hole in the back plate.

6. Connect the white tube to the remaining side connection of the restrictor tee. Inser excess spring. Insert the white tube through a hole on the right hand bracket next to the transmitter, and then insert through the oblong hole in the back plate.

7. Install the insulator card by inserting the black tube through the

t hand hole and the white tube through the ri

lef

8. Insert the black tube into the left hand hole in the wall fitting or connect to the main line.

9. Insert the white connect to the transmitter (bran

10. Attach the transmitter back plate to the wall box with screws provided.

11. Replace cover and tighten cover screw.

through a hole in the left hand side bracket and

t the other spri

tube into the right hand hole in the wall fitting or

ng into the tube and cut o f and

ght hand hole.

ch) output line.

Mounting of TKS-6001 on Light Troffer

Figure-6

Mountin

The transmitter must be located in the return air grille opposite the fixture exhaust air opening when mounting in recessed combination light fixture/air diffuser (See Figure 5).

A 1/2" knockout is provided in the corre for the admittance of the transmitter. Light Fixtures come equipped with the return air grille assembly attached to the hinged access door (See Figure 6).

g Location

ct end of the light fi

xture shell

Mounting

Barbed end fitting for 5/32" plastic tubing. Run shortest length of 5/32" plastic tubing possible from transmitter [no more than 3 ft. (1 m)] before connecting to 1/4" plastic tubing.

Figure-5 Locating TKS-6001 in Troffer End Opposite

Exhaust Grill.

Page 4