Schlage KC9232,KC9232-2,KC9233-2,KC9233 Installation Manual
KING COBRA/KING COBRA-2
NARROW STILE SERIES
KC9232/KC9232-2 KC9233/KC9233-2
Keypad Programmable
and SNAP Compatible Trim
For Narrow Stile Doors
57041-D 04-11-2007
KC9232/KC9232-2 & KC9233/KC9233-2 INSTALLATION
Contents of the Box
KC9232/KC9232-2 & KC9233/KC9233-2 INSTALLATION
Contents of the Box
57041-D Page 2 04-11-2007
KC9232/KC9232-2 & KC9233/KC9233-2 INSTALLATION
1
1/8” wide blad
Introduction / Tools and Materials Needed / Contact Info
Introduction / Tools and Materials Needed / Contact Info
Introduction:
The KC9232/KC9232-2 and KC9233/KC9233-2 are designed to replace existing
exterior cylinders or trim on Adams Rite® deadlatches. The trim will retract the
deadbolt or latch when an access code or iButton is entered and the knob is turned.
Mechanical key override is standard. The trim is compatible with interior devices
such as a thumbturn or mortise cylinder. Adams Rite® deadbolt accessories 4015
threshold bolt and 4016 header bolt are also compatible with these models of the
KC9000 series trim. With existing or new Adams Rite® trim on the inside the
‘hold back’ feature is still possible for a continued unlatched function (see Adams
Rite® instructions where applicable). An Audit Trail feature is available on the
KC9232-2 and the KC9233-2 models.
The KC9232/KC9232-2 (trim w/knob & MS Cam interface) is compatible
with Adams Rite® MS1850, MS1850-050, MS1950, 4070 Deadbolts, 4710
Deadlatch locks and 8400 mortise exit devices.
The KC9233/KC9233-2 (trim w/knob and 4070 Cam interface) is compatible
with Adams Rite® 4070 Short Throw Deadbolt.
Tools and Materials Needed:
.Flat head screwdriver w/straight,
2. Small Philips head screwdriver
3. 3/32” Allen wrench
4. 1/16” Allen wrench
5. Center punch
6. Hammer
7. Pencil
8. Drill & Tap for 10-32 threads
Contact Information:
Schlage Lock Company
575 Birch Street
Forestville, CT 06010
technical support: 866-322-1237
fax: 866-322-1233
web: http://www.irsupport.net
e.
57041-D Page 3 04-11-2007
KC9232/KC9232-2 & KC9233/KC9233-2 INSTALLATION
Door Preparation
Door Preparation
Door Conditions:
Installation may require the use of a cover plate (a) to cover the holes left in the door.
If the existing pull (b) must be removed, Ives offers a compatible pull.
>Schlage Cover Plate P/N: KC9000-KRP
>Ives Pull P/N: 8190-18-xxx (xxx = finish)
Backset is determined by
the Adams Rite® lock.
b
a
6-21/32”
(6.656”)
For factory prepped doors, use dimensions
shown. Dimensions are referenced from center
of 1-1/4” cylinder hole. Backset is determined
by the Adams Rite® lock.
When installing new Adams Rite® locks, do
not install outside cylinder because this trim
replaces it. Do not install face plate at this time
because access to the cylinder set screw in the
lock will be required during installation.
57041-D Page 4 04-11-2007
3-31/32”
(3.962”)
2-45/64”
(2.697”)
KC9232/KC9232-2 & KC9233/KC9233-2 INSTALLATION
C9000
108
016
C9000
1/8”
N
Cams, Cores, Cylinders and Blocking Rings
Cams, Cores, Cylinders and Blocking Rings
Cams For Mechanical Override Cylinder:
The K
is a list of compatible Schlage parts. For other manufacturers,
consult cross-reference charts.
> Cam for Standard Mortise cylinder: Schlage Everest: L583-153
Schlage Classic: L583-254
> Cam for Interchangeable Core: Schlage IC Cam: L583-255
trim requires the use of a clover leaf cam (a). This
IC Cores:
> Small Format IC core w/ cam: Schlage: 80-
NOTE: This core requires the use of 1/4” blocking ring:
Schlage: 36-079-025-<FINISH>
-<FINISH>
a
> Full Size IC core w/ cam: Schlage: 30-
NOTE: This core requires the use of 3/8” blocking ring:
Schlage: 36-079-037-<FINISH>
-<FINISH>
Cylinders / Blocking Rings:
The K
of a blocking ring. For cylinders longer
ring is required. The blocking ring thickness is equal to the cylinder length, minus 1-1/8”. For example, if you use a 1-1/2” cylinder you need a 3/8” blocking ring. Compression rings can be
ordered from a Schlage distributor:
Thickness: Schlage Part Number:
o compression ring: 1/8” 36-079-012-<FINISH>
1/4” 36-079-025-<FINISH>
3/8” 36-079-037-<FINISH>
1/2” 36-079-050-<FINISH>
can use a 1-
mortise cylinder without the use
than 1-1/8” a blocking
57041-D Page 5 04-11-2007
KC9232/KC9232-2 & KC9233/KC9233-2 INSTALLATION
1/8” l
Installing the KC9232/KC9232-2 or KC9233/KC9233-2
Installing the KC9232/KC9232-2 or K C9233/KC9233-2
Installing the KC9232/KC9232-2 or KC9233/KC9233-2
If your trim has a key cylinder already installed, skip to Position the Dead Latch’s Set Screw
Hole: on page 10. Otherwise, continue with Loosen the Baseplate Screws: on this page .
1) Loosen the Baseplate Screws:
IMPORTANT: Do not remove any of the screws in the following step or it will be difficult to reinstall them.
• Using a small Philips head screwdriver, loosen
screws a & b in baseplate, around key cylinder
hole, one turn.
NOTE: Screws a, b, c & d are set at the factory.
Screws a & b are tightened and screws c & d are left loose.
c
d
a
2) A Key Cylinder That Is At Least 1-1/8” Long Must Be Installed:
> The key cylinder that you install must be 1-
>>>> Do not attempt to install a key cylinder that is shorter than 1-1/8”
> The two illustrations below show the difference between a 1” and a 1-1/8” key cylinder.
1” long key cylinder.
DO NOT ATTEMPT TO INSTALL A 1”
LONG KEY CYLINDER.
ong or longer.
b
57041-D Page 6 04-11-2007
1-1/8” long key cylinder
ONLY INSTALL A KEY CYLINDER
THAT IS AT LEAST 1-1/8” LONG.
Loading...