P515-549
Example
BE365
FE575
BE365, FE575, FE595
Programming/Operating Guide
Table of Contents
BE365 Features .......................................................2
Lock Operation ............................................2
Changing the Battery ...................................3
FE575 Features .......................................................4
Lock Operation ............................................4
Changing the Battery ...................................5
FE595 Features .......................................................6
Lock Operation ............................................6
Changing the Battery ...................................7
Programming for All Models ....................................8
Keeping Your Lock Secure .....................................10
Key Override ..........................................................10
Troubleshooting Guide ...........................................11
Emergency Lock Override .....................................12
FE595
Preset Codes
Programming Code: 123456
User Code A: 4321
User Code B: 5678
S/N: 1-00000000
Model: BE365
Example
Preset Programming Code
Serial Number
Lock Series
Preset User Codes
Place Label Here
BE365 Features
A. Button
B. Keypad
C. Key Override
D. Outside Thumbturn
E. Inside Thumbturn
A. Button
1. Press to turn on backlight.
2. Press to clear an incorrect code entry.
B. Keypad
1. Use to unlock the lock by entering a
valid four-digit user code.
2. Use to program the lock. (See page 8.)
BE365 Lock Operation
To Retract the Deadbolt
a. Enter a valid four-digit user code.
b. The
c. Rotate outside thumbturn within fi ve
seconds to retract deadbolt.
b
button will fl ash green.
C. Key Override (See page 10.)
D. Outside Thumbturn
Freely rotates until deadbolt is activated.
Then thumbturn will extend or retract
deadbolt.
E. Inside Thumbturn
Extends and retracts the deadbolt from
the inside.
To Extend the Deadbolt
a. Push button.
b. Rotate outside thumbturn while
button is lit to extend deadbolt.
a
a
c
b
2
BE365 Lock Operation Continued
Locked - Deadbolt Extended Unlocked - Deadbolt Retracted
Locked User code
Deadbolt
required
for entry
BE365 Changing the Battery
For low battery indications, see page 11.
NOTE: Replace with premium 9V alkaline battery.
Unlocked No user code
required
for entry
b
Reverse steps to assemble lock.
c
a
d
3
FE575 Features
A. Button
B. Keypad
C. Key Override
D. Outside Knob/Lever
E. Inside Knob/Lever
A. Button
1. Press to turn on backlight.
2. Press to clear an incorrect code entry.
B. Keypad
1. Use to unlock the lock by entering a
valid four-digit user code.
2. Use to program the lock. (See page 8.)
FE575 Lock Operation
To Unlock the Lock
a. Enter a valid four-digit user code.
(See note.)
b. The
c. Rotate outside knob/lever within
fi ve seconds to open door.
d. After fi ve seconds, the lock will
automatically relock.
button will fl ash green.
C. Key Override
(See page 10.)
D. Outside Knob/Lever
Always rotates. Only retracts latch when
lock is unlocked.
E. Inside Knob/Lever
Always rotates and retracts latch for
immediate exit.
b
a
NOTE: The lock has two unique
preset user codes that are printed on
the front page of this guide and back
of the keypad assembly.
4
c
FE575 Changing the Battery
For low battery indications, see page 11.
NOTE: Replace with premium 9V alkaline battery.
c
b
a
f
e
Reverse steps to assemble lock.
d
5
FE595 Features
A. Button
B. Keypad
C. Key Override
D. Thumbturn
E. Outside Knob/Lever
F. Inside Knob/Lever
A. Button
1. Press to turn on backlight.
2. Press to clear an incorrect code entry.
B. Keypad
1. Use to unlock the lock by entering a
valid four-digit user code.
2. Use to program the lock. (See page 8.)
C. Key Override
(See page 10.)
D. Thumbturn
Switches between locked and unlocked.
(See below.)
E. Outside Knob/Lever
Always rotates. Only retracts latch when
lock is unlocked.
F. Inside Knob/Lever
Always rotates and retracts latch for
immediate exit.
FE595 Lock Operation
Thumbturn in Locked Position Thumbturn in Unlocked Position
Locked User code
required
for entry
Unlocked No user code
required for
entry
6
FE595 Lock Operation Continued
To Unlock the Lock
(While thumbturn is in locked
position)
a. Enter a valid four-digit user code.
(See note.)
b. The
c. Rotate outside knob/lever within fi ve
seconds to open door.
d. After fi ve seconds, the lock will
automatically relock.
NOTE: The lock has two unique preset
user codes that are printed on the
front of this guide and back of keypad
assembly.
button will fl ash green
c
a
b
FE595 Changing the Battery
For low battery indications, see page 11.
NOTE: Replace with premium 9V alkaline battery.
b
a
c
d
Reverse steps to assemble lock.
7
Programming for All Models
Example
Label is located on front of guide and back of keypad assembly.
Four-Digit User Codes
(4DUC)
• Activates lock
• Can be changed
• Up to 19 user codes
• Won't program lock
Programming Code: 123456
User Code A: 4321
User Code B: 5678
S/N: 1-00000000
Model: BE365
Example
Six-Digit Programming Code
(6DUC)
• Programs lock
• Can be changed
• Won't operate lock
Schlage Button (on front of lock)
• Lights orange while in programming mode.
• Flashes green when programming is successful.
• Lights red when there is an error. Retry steps or see troubleshooting guide on page 11.
• Press to exit programming mode at any time.
• Wait until
button stops fl ashing before entering additional codes.
Legend
= Schlage Button
= Specifi c Number on Keypad
6DPC = Six-Digit Programming Code
4DUC = Four-Digit User Code
Add a new user code
6DPC New 4DUC Reenter New 4DUC
Delete one existing or preset user code
6DPC Existing 4DUC Reenter Existing 4DUC
Change current or preset programming code
IMPORTANT: If you forget your new programming code, you will have to reset the lock.
6DPC New 6DPC Reenter New 6DPC
Enable/disable all user codes
1. Disable All User Codes: 6DPC
2. Enable All User Codes: 6DPC
Turn beeper on or off (preset is on)
NOTE: Lock will still beep when battery is low.
6DPC
Delete ALL user codes at once
IMPORTANT: This will delete all the user codes but not the programming code.
6DPC Reenter 6DPC
8
Enable/disable Turn Lock feature (BE365 ONLY) (preset is enabled)
NOTE: When Turn Lock feature is disabled, you must enter a valid user code to extend the
bolt.
6DPC
Create a temporary code (house sitter, plumber, etc.)
1. Add New User Code:
6DPC New 4DUC Reenter New 4DUC
2. Give person his/her code, but keep a written copy for yourself.
3. When code is no longer needed, delete User Code:
6DPC Existing 4DUC Reenter 4DUC
Delete a user code if user code is unknown
IMPORTANT: This will delete ALL the user codes but not the programming code.
1. Delete ALL User Codes:
6DPC Reenter 6DPC
2. Add New User Code:
6DPC New 4DUC Reenter New 4DUC
3. Repeat step 2 until all User Codes are reentered.
Ensure only you have codes to the lock
1. Change Programming Code:
6DPC New 6DPC Reenter New 6DPC
2. Delete ALL User Codes:
6DPC Reenter 6DPC
3. Add New User Code:
6DPC New 4DUC Reenter New 4DUC
Restore ALL preset lock settings
IMPORTANT: Lock will be reset to the preset programming and user codes. All existing
user codes and current programming code will be erased.
1. Disconnect the battery.
(For FE575, see page 3. For FE595, see page 5. For BE365, see page 7.)
2. Press and release
3. Reconnect the battery and wait until
4. Within 10 seconds, press and hold
.
is no longer lit.
until lights green and the lock beeps.
9
Keeping Your Lock Secure
Security Tips
1. Do not share your programming code with other people.
2. Write down your programming and user codes and keep them in a safe place.
(Use the table below if desired.)
3. Give each person his/her own user code. You can have up to 19 user codes.
4. If you don't remember or don't know who has a user code, you can delete all the user
codes. (See page 8.)
Name User Code Name User Code Name User Code
Key Override
Use key override to unlock the lock in the following situations:
1. Battery is dead.
2. No User Code is known.
FE575 and FE595
NOTE: Key does not retract latch.
Insert Key
Rotate key
270° to unlock. Rotate knob/lever.
Rotate key 270°
back to relock.
270°
Key cannot be
removed in this
position.
BE365 Only
NOTE: Key will both extend and retract deadbolt.
When finished,
remove key.
270°
10
Insert key.
Rotate key 90°.
90°
Push key into
thumbturn.
Rotate key and
thumbturn 90°.
90°
Troubleshooting Guide
Problem Beeps* Lights Solution
User code (4DUC) does not
unlock lock.
does not light when
numbers are pressed.
There is a delay before unlock
after a valid 4DUC is entered.
blinking red but no codes
have been entered.
Cannot add a new 4DUC.
Cannot delete a 4DUC. 2 Red
Cannot change 6 digit
programming code (6DPC).
Cannot delete all user codes. 2 Red 6DPC entered second time is incorrect.
Lock will not stay in
programming mode.
For BE365, after pushing
Schlage button and rotating
thumbturn, the deadbolt does
not extend.
I forgot my 6DPC. None None
Outside thumbturn does not
freely spin after deadbolt is
thrown.
* Number of beeps if beep is turned on.
2 Red 4DUC entered is not a valid 4DUC.
1 High,
1 Low
None None
High/Low,
then 1
None
High/Low Red
2 Red
2 Red
2 Red
None None Turn Lock Feature is disabled. See page 9.
None None Lock is malfunctioning. See page 12.
Green then
Red
Red then
Green
Quick Red
Blinking
User codes have been disabled. Enable User
Codes. (See page 8.)
1. Too many incorrect user codes have been
entered. Wait 30 seconds and try again.
2. If keypad does not respond after 30
seconds, then replace battery.
For FE575, see page 3.
For FE595, see page 5.
For BE365, see page 7.
Battery is low and should be replaced.
For FE575, see page 3.
For FE595, see page 5.
For BE365, see page 7.
Battery is dead and MUST be replaced.
For FE575, see page 3.
For FE595, see page 5.
For BE365, see page 7.
19 4DUCs already exist. Delete a 4DUC
before adding a new one. (See page 8.)
1. Second 4DUC entered did not match fi rst
4DUC entered.
2. The 4DUC matches the fi rst four digits of
the existing 6DPC.
Second 4DUC entered did not match fi rst
4DUC entered.
1. Second 6DPC entered did not match fi rst
6DPC entered.
2. First four digits of new 6DPC match an
existing 4DUC.
1. Any key other than
immediately after programming mode was
entered.
2. An incorrect entry was made during the
programming process.
1. Check front of manual or back of keypad
assembly for preset 6DPC.
2. If needed, restore lock to preset settings.
(See page 9.)
was pressed
Schlage Customer Service
U.S.A. and Canada
P.O. Box 1210
Olathe, KS 66051-1210
(888) 805-9837
Fax (800) 366-5625
www.schlage.com
11
Emergency Lock Override
If the outside thumbturn does not freely rotate or the lock is malfunctioning, you can
enable the emergency override feature. When emergency override is engaged, a key
must be used to extend/retract the deadbolt.
a. Remove screws and thumbturn assembly.
b. Disconnect and remove battery.
c. Use screwdriver to rotate slot on mounting plate
to "LOCKOUT" position.
NOTE: You may need to have your lock repaired or
replaced.
c
a
b
12
Loading...