SCHLAGE CONNECT™
Touchscreen Deadbolt with Alarm
Installation Instructions
PACKAGE CONTENTS
Camelot Style Shown
Backup Key
Touchscreen
Assembly
ENGLISH
Set Screw
Throughout Guide
Bolt
Support Plate
Battery Cover
Alarm
Assembly
Strike
Reinforcement
Plate
2
Bolt/Strike
Screws (4)
Alarm Assembly
Screw
Century Style
Support Plate
Screws (2)
Reinforcement
Screws (2)
LET’S GET STARTED!
Once you have all your tools together, please follow each step carefully and in order. Because
this is an electronic lock, the order of steps is very important. If you skip a step, you may have
to perform a factory default reset and start over.
You will denitely need this tool:
• Phillips screwdriver
You can use a manual or electric
screwdriver, but please DO NOT use a
power drill!
You may also need these tools:
• Tape Measure
• Flathead Screwdriver
• Pencil
• Wood Block
• Hammer
INSTALLATION NOTES! PLEASE READ!
• DO NOT use a power drill for installation! This could damage the lock.
• Please read all the instructions before calling customer support.
• Please call customer support before returning the product to the store.
• DO NOT install the batteries before installing the lock! Follow the instructions in order!
• If you have previously installed this lock on another door, you MUST perform a
Factory Default Reset FIRST! See the User’s Guide for more information.
• This lock is designed for the following operating temperatures:
• Outside Lock Body (exterior mounted): -31˚F (-35˚C) to 151˚F (66˚C)
• Inside Lock Body (interior mounted): 14˚F (-10˚C) to 120˚F (49˚C)
STEPS AT A GLANCE
1 Check current door/frame alignment. ....................................................................................4
2 Remove the current deadbolt from the door. ........................................................................4
3 Watch the online video. ...........................................................................................................4
4 Check door/frame dimensions. ..............................................................................................5
5 Locate programming and User Codes. ..................................................................................5
6 Install bolt and strike. ..............................................................................................................6
6a Adjust bolt length, if necessary. ..........................................................................................6
6b Change the faceplate, if necessary. ...................................................................................6
6c Install the bolt into the door. ................................................................................................7
6d Install the strike into the frame. ...........................................................................................7
6e Test bolt alignment. .............................................................................................................8
7 Install the Touchscreen Assembly..........................................................................................8
7a Install the Touchscreen on the outside of the door. ............................................................8
7b Install the Support Plate on the inside of the door. .............................................................9
8 Install the Alarm Assembly. .....................................................................................................9
8a Remove the battery cover from the Alarm Assembly. .........................................................9
8b Connect the cable to the Alarm Assembly. .......................................................................10
8c Install the Alarm Assembly. ...............................................................................................10
8d Secure the Alarm Assembly to the Support Plate. ............................................................11
9 Install the Batteries. ...............................................................................................................11
9a Install the batteries into the battery tray. ...........................................................................11
9b Install the battery cover. ....................................................................................................12
10 Set up the Lock. .....................................................................................................................12
11 Test the Lock. .........................................................................................................................12
11a Extend the bolt (lock) using the inside thumbturn. ............................................................12
11b Extend the bolt (lock) using the Touchscreen. ..................................................................13
11c Retract the bolt (unlock) using the Touchscreen. .............................................................13
11d If the lock failed to lock or unlock: .....................................................................................13
12 Continue to the User’s Guide. ..............................................................................................14
ENGLISH
3
1 Check current door/frame alignment.
Because the bolt on this lock is extended automatically, it is important that the door and frame
are aligned. Use this checklist to determine if your current alignment will work without any
adjustment.
I can lock the door without pushing, pulling or lifting the door.
My door alignment— the ability to lock the door easily and smoothly— stays the same with
changing seasons.
When the door is closed, there is space for the deadbolt to extend 1” into the frame when
locked.
If you could not check every box in the checklist, you will need to adjust your door and/or
frame. Please visit answers.schlage.com for more information.
2 Remove the current deadbolt from the door.
Remove the entire deadbolt, including the bolt. You may also want to remove the strike.
ENGLISH
L In order to maintain BHMA Grade 1, you must install the included reinforcement plate and
strike (see step 6d on page 7).
L A standard Schlage deadbolt is shown. Check with your specic deadbolt manufacturer if
you need help.
3 Watch the online video.
The online videos will give you a good overview of the installation process. Please visit
answers.schlage.com and then click on Touchscreen Deadbolt with Alarm. Watch the
video Installing the Touchscreen Deadbolt With Alarm. You can also scan the code on the
back of this guide with your smartphone.
4
4 Check door/frame dimensions.
Place Label Here
Coloque la Etiqueta Aquí
Apposer l’étiquette ici
SCHLAGE
00000000
BE469
Firmware Ver.: xxx-x
Programming Code: 000000
User Code A: 0000
User Code B: 0000
0000000-000
00000000
FCC ID: xxxxxxxx
SCHLAGE
00000000
BE469
Firmware Ver.: xxx-x
Programming Code: 000000
User Code A: 0000
User Code B: 0000
0000000-000
00000000
FCC ID: xxxxxxxx
SCHLAGE
00000000
BE469
Firmware Ver.: xxx-x
Programming Code: 000000
User Code A: 0000
User Code B: 0000
0000000-000
00000000
FCC ID: xxxxxxxx
• Measure the dimensions shown. If your door dimensions
do not match, you will need to change your door
preparation. Go to answers.schlage.com for drilling
instructions.
L If your door is thicker than 1C\v”, you will need a thick
door kit. Please call Customer Service:
L Mark your crossbore and backset measurements
on this page. You will need these measurements for installation. Either measurement is
normal.
Backset
2C\,” (60 mm)
OR
Crossbore
2C\v” (70 mm)
Diameter
2Z\,” (53 mm)
OR
1Z\x" (38 mm)
1” (25 mm)
Hole
Minimum 5"
(127 mm)
This lever represents
your current knob or
lever, which may be
already installed.
Door Thickness
1C\,” to 1C\v”
Toll-Free Calling From:
U.S.A.: (888) 805-9837
Canada: (800) 997-4734
Mexico: 018005067866
Door Stop
Hole at least
1” (25 mm)
deep.
ENGLISH
5 Locate Programming and User Codes.
Codes are located on the sticker on the back of the User’s Guide. You will need these codes
to operate the lock. They are also located on the back of the Alarm Assembly.
L Do NOT remove the sticker from the back of the lock! If you lose your Programming Code,
you can reset your lock back to these default codes.
If you have questions about
Si tiene dudas acerca de cualquier
parte de la instalación o programación,
no devuelva el cerrojo de pantalla
táctil con alarma a la tienda. Nuestros
representantes del Departamento de
installation or programming, don’t return
Servicio de Asistencia al Cliente de
the Keypad Lock to the store. Our Schlage
Schlage están listos para ayudarlo.
Customer Service representatives are ready
to help.
Línea gratuita
: 1.888.805.9837
Chat en vivo
: schlage.com
Toll-Free: 1.888.805.9837
Live Chat: schlage.com
Para obtener más información sobre
este producto, escanee el código con
un teléfono inteligente.
Descargue la aplicación en
scanlife.com.
Códigos Predeterminados
BE469
Firmware Ver.: xxx-x
Predeterminado
Programming Code: 000000
Si vous avez des questions
concernant l’installation ou
programmation, ne ramenez
pas le pêne dormant avec
écran tactile muni d’une alarme
au magasin. Les représentants
du service à la clientèle de
Schlage sont à votre service.
Sans frais
: 1.888.805.9837
Clavardage en direct : schlage.com
Pour de plus amples renseignements
sur ce produit, numérisez le code avec
votre téléphone intelligent.
Téléchargez l’application au
scanlife.com.
&RGHVSUpGp¿QLV
SCHLAGE
00000000
0000000-000
User Code A: 0000
User Code B: 0000
FCC ID: xxxxxxxx
24060857 Rev. 01/14-a
00000000
Printed in Country
The same codes
are located in both
places.
© Allegion 2014
any part of installation or
programming, don’t return
the Touchscreen Deadbolt
with Alarm to the store. Our
Schlage Customer Service
representatives are ready to
help.
Toll-Free: 1.888.805.9837
Live Chat: schlage.com
To learn more about this
product, scan the code with
your smartphone.
Download the app at
scanlife.com.
Default Codes
24060857
Default Programming Code
Código de Programación
&RGHGHSURJUDPPDWLRQSUpGp¿QL
Default User Codes
Códigos de Usuario Predeterminado
&RGHVG¶XWLOLVDWHXUSUpGp¿QLV
5
6 Install bolt and strike.
6a Adjust bolt length, if necessary.
• If the backset (see step 4 on page 5) of your door was 2C\,” (60 mm), you do not
need to do anything. Proceed to step step 6b.
• If the backset (see step 4 on page 5) of your door was 2C\v” (70 mm), you need to
adjust your bolt. Twist the faceplate until the button pops into the 2C\v” space.
Twist the
faceplate.
Make sure the button
pops into place.
ENGLISH
6b Change the faceplate, if necessary.
L In step 6c, your installation will depend on which kind of door edge you had in this step.
If your door looks like this, you don’t
Mortise
need to do anything. Go to step 6c.
OR
Alternate Mortise
Use the square-corner faceplate if
desired. A square-corner faceplate can
be purchased from Customer Support.
1. Use a athead screwdriver to pry the
faceplate off.
2. Press the square-corner faceplate
into place. The faceplate may
not stay in place until screws are
installed in next step.
If your door looks like this, complete the
No Mortise
steps below.
OR
1. Use a athead screwdriver to pry the
faceplate off.
2. Remove the backplate.
3. Slide the round faceplate into place.
3. Go to step 6c, Figure A.
6
4. Go to step 6c, Figure B.
6c Install the bolt into the door.
Choose the picture below that matches your door.
FIgure A: Mortise Figure B: No Mortise
Make sure
the word
TOP faces
up when
installing
the bolt.
OR
Actual Size (2)
Use a block of wood and
a hammer (not included)
to tap the bolt into place.
You don’t need to use the
screws.
6d Install the strike into the frame.
Install all the parts shown for maximum security.
L In order to maintain BHMA Grade 1, you must install the included reinforcement plate and
strike.
Door Stop
Make sure this
hole is at least 1”
Actual Size (2)
Reinforcement Screws: Actual Size (2)
(25 mm) deep.
ENGLISH
L The reinforcement screws may not t on doors with sidelights.
7
6e Test bolt alignment.
1. Close the door.
2. Insert a athead screwdriver into the slot in the bolt, as shown.
3. Rotate the screwdriver toward the door edge to extend the bolt into the hole in the frame.
This operation should be smooth. You should be able to rotate the screwdriver 90˚, fully
extending the bolt.
4. If the operation was not smooth, or if the bolt did not fully extend, adjust your frame and/or
door preparation. Go to answers.schlage.com and watch the video Proper Alignment of
Door and Frame for a Smoothly Operating Lock for further instructions.
5. Retract (unlock) the bolt before continuing to step 7.
L If the deadbolt continues to rub against the strike, contact Customer Support for an
alternate strike with an additional .060” (2 mm) clearance.
CAUTION
Test from the inside to
avoid being locked out!
ENGLISH
If you can rotate the
screwdriver a full
90˚, then the bolt is
fully extended.
Retract the bolt
before continuing
to step 6.
7 Install the Touchscreen Assembly.
7a Install the Touchscreen on the outside of the door.
L The clips snap into the crossbore (see step 4 on page 5) to assist in holding the
keypad on the door.
L The Touchscreen Assembly should install smoothly. If it does not, check that the bolt is set
to the correct backset (see step 6a on page 6).
Route the cable
under the bolt.
Clips snap into
the crossbore.
Align the tab
with the notch.
L NOTE: If you have a crossbore (see step 4 on page 5) that is slightly less than 2Z\,”
(54 mm), the lock may not install smoothly. You can remove the spacer. Always remove
the spacer for a 1Z\x” (38 mm) crossbore. See Spacer Removal on page 15 before
continuing.
8
7b Install the Support Plate on the inside of the door.
L Make sure the Touchscreen and Support Plate are straight on the door before tightening
the screws. Tighten screws fully to prevent the lock from moving over time.
TOP
Have someone hold
the Touchscreen on the
outside of the door while
you tighten the screws.
Make sure the
indented circle is
facing the door.
Route the cable
through the slot.
Actual Size (2)
8 Install the Alarm Assembly.
8a Remove the battery cover from the Alarm Assembly.
ELECTROSTATIC DISCHARGE
WARNING!
Touching the circuit board
may damage the lock!
DO NOT remove
the battery tray
(not shown)!
ENGLISH
9
8b Connect the cable to the Alarm Assembly.
L Locate the screws in step 8d before beginning this step so they will be handy when you
need them.
The connector ts only one
way. Match the dot on the
connector with the dot on the
circuit board.
ENGLISH
8c Install the Alarm Assembly.
1. Align the tab with the notch as shown.
2. Route the cable into the channel.
3. Then slide the Alarm Assembly towards the door.
Route the cable into
the channel to avoid
crimping the cable.
Align tab with
notch.
10
8d Secure the Alarm Assembly to the Support Plate.
Install the lower
screw rst.
Actual Size
Actual Size
8-32 x 1Z\,”
8-32 x .187 UP FHMS
NOTE
Please do not rotate the thumbturn at this time. It may not rotate
easily. Setup will be performed after installation is complete.
9 Install the Batteries.
9a Install the batteries into the battery tray.
1. Unsnap the connector.
2. Remove the battery tray.
3. Install four high-quality alkaline AA batteries.
L Lithium batteries may cause undesirable
operation.
4. Carefully replace the battery tray, with the
batteries facing the door.
5. Snap the connector back into place.
ELECTROSTATIC DISCHARGE
WARNING!
Touching the circuit board
may damage the lock!
ENGLISH
-
+
-
+
+
-
+
-
11
9b Install the battery cover.
10 Set up the Lock.
ENGLISH
1. Open the door if it is not already open.
2. Press the Outside Schlage Button.
3. Enter one of the Default User Codes into the
lock (see step 5 on page 5).
4. The lock will perform a setup routine. Wait until
the bolt stops moving before continuing.
L If the Touchscreen did not light up during this
step, you may have a power problem. Install
fresh batteries and make sure the battery wires
are connected (see step 9a on page 11).
If that does not help, make sure the cable is
connected and is not crimped (see step 8b on
page 10).
Speaker Hole
DO NOT install screw!
11 Test the Lock.
CAUTION
Keep the key with you
during testing to avoid
being locked out!
11a Extend the bolt (lock) using the inside thumbturn.
1. Close the door.
2. Rotate the thumbturn toward the door jamb to extend the
bolt.
Was this operation smooth?
Continue to
step 11b.
You may need to adjust your door/
frame. Continue to step 11b for
further testing, or go to answers.
schlage.com and watch the video
Proper Alignment of Door and
Frame for a Smoothly Operating
Lock for adjustment instructions.
L For complete information about programming
and light/beep patterns, see the Programming
the Touchscreen and Troubleshooting
sections in the User’s Guide.
NOYES
12
11b Extend the bolt (lock) using the Touchscreen.
1. Unlock the door using the thumbturn if you have
not already.
2. Take the key and the Default User codes with you!
Go outside and close the door.
3. Press the Outside Schlage Button.
4. The bolt should extend.
Did the bolt extend (is the door locked)?
NO
You need to adjust your
door/frame. Go to
answers.schlage.com
for adjustment
instructions.
Did the bolt take two tries to
Each try sounds like two
Alignment is
NO
correct.
YES
extend?
cycles.
YES
The lock has both a low power and
high power mode. It will try low power
rst and then high power when
unsuccessful. After three times using
high power, it will always use the high
power mode instead of trying twice each
time. You may want to adjust your door/
frame to conserve battery power, but it
is not necessary.
11c Retract the bolt (unlock) using the Touchscreen.
1. Press the Schlage button.
2. Enter one of the default User Codes into the lock.
3. The bolt should retract.
Did the bolt retract (is the door unlocked)?
NO
YES
ENGLISH
Use the key to unlock the
door. You need to adjust
your door/frame. Go to
answers.schlage.com
for adjustment
instructions.
Alignment is
correct.
11d If the lock failed to lock or unlock:
1. If the Touchscreen did not light up, you may have a power problem. Install fresh batteries
and make sure the battery connector is connected (see step 9a on page 11). If that
does not help, make sure the cable is connected to the Alarm Assembly and is not
crimped (see step 8b on page 10).
2. If the lock had power but you need to adjust your door/frame, please go online to
answers.schlage.com for complete adjustment instructions and videos.
13
12 Continue to the User’s Guide.
Your lock is installed and functional. Continue to the User’s Guide for complete information
about how to congure and operate the lock and alarm.
ENGLISH
14
SPACER REMOVAL
(OPTION FOR SMALL CROSSBORES ONLY)
ONLY if your door has less than a 2Z\," (54 mm) crossbore, remove the spacer as shown.
Less than 2Z\," (54 mm)
Crossbore
1. Remove screw. 2. Rotate and remove spacer. 3. Replace screw.
ENGLISH
NEED HELP?
Please call customer support before returning the product to the store.
Toll-Free Calling From: U.S.A.: (888) 805-9837
Canada: (800) 997-4734
Mexico: 018005067866
Visit our web site for videos, FAQs and more: answers.schlage.com
15
Loading...