Scag STT61V-31EFI-SS User Manual

Page 1
OPERATOR’S MANUAL
Turf Tiger
Model: STT61V-31EFI-SS
Congratulations on owning a Scag mower! This manual contains the operating instructions and safety information for your Scag mower. Reading this manual can provide you with assistance in maintenance and adjustment procedures to
keep your mower performing to maximum efciency. The specic models that
this book covers are listed on the inside cover. Before operating your machine, please read all the information enclosed.
© 2008 Scag Power Equipment Division of Metalcraft of Mayville, Inc.
PART NO. 03242 Rev. 1
PRINTED 3/2008
PRINTED IN USA
Page 2
WARNING
FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN
SERIOUS INJURY OR DEATH.
Read this manual completely as well as other manuals that came with your mower.• DO NOT operate on steep slopes. To check a slope, attempt to back up it (with the •
cutter deck down). If the machine can back up the slope without the wheels slipping, reduce speed and use extreme caution.
Under no circumstances should the machine be operated on slopes greater than 15 • degrees. ALWAYS FOLLOW OSHA APPROVED OPERATION.
DO NOT mow on wet grass. Wet grass reduces traction and steering control.• Keep all shields in place, especially the grass discharge chute.• Before performing any maintenance or service, stop the machine and remove the •
spark plug wire and ignition key. If a mechanism becomes clogged, stop the engine before cleaning.• Keep hands, feet and clothing away from power-driven parts.• Keep others off the mow• er (only one person at a time)
REMEMBER - YOUR MOWER IS ONLY AS SAFE AS THE OPERATOR!
HAzARD CONTROL AND ACCIDENT PREvENTION ARE DEPENDENT UPON THE AWARENESS, CONCERN, PRUDENCE, AND PROPER TRAINING OF THE PERSONNEL INvOLvED IN THE OPERATION, TRANSPORT, MAINTENANCE, AND STORAGE OF THE EqUIPMENT.
This manual covers the operating instructions and illustrated parts list for:
STT61v-31EFI-SS with a serial number of E2600001 to E2699999
SMT-61v with a serial number of D9500001 to D9599999
Always use the entire serial number listed on the serial number tag when referring to this product.
Page 3
R
Table of Contents
TABLE OF CONTENTS
GENERAL INFORMATIONSECTION 1 - ...................................................................................1
1.1 INTRODUCTION ...........................................................................................................................................1
1.2 DIRECTION REFERENCE ...........................................................................................................................1
1.3 SERvICING THE ENGINE AND DRIvE TRAIN COMPONENTS .................................................................1
1.4 SYMBOLS ....................................................................................................................................................2
SAFETY INFORMATIONSECTION 2 - ......................................................................................3
2.1 INTRODUCTION ...........................................................................................................................................3
2.2 SIGNAL WORDS ..........................................................................................................................................3
2.3 BEFORE OPERATION CONSIDERATIONS ................................................................................................3
2.4 OPERATION CONSIDERATIONS ................................................................................................................4
2.5 ROLL-OvER PROTECTION SYSTEM .........................................................................................................6
2.6 MAINTENANCE CONSIDERATIONS & STORAGE ....................................................................................8
2.7 SAFETY AND INSTRUCTIONAL DECALS .................................................................................................9
SPECIFICATIONSSECTION 3 - ..............................................................................................10
3.1 ENGINE ......................................................................................................................................................10
3.2 ELECTRICAL .............................................................................................................................................10
3.3 POWER HEAD ...........................................................................................................................................10
3.4 CUTTER DECk ..........................................................................................................................................11
3.5 HYDRAULIC SYSTEM ...............................................................................................................................11
3.6 WEIGHTS AND DIMENSIONS ...................................................................................................................11
3.7 PRODUCTIvITY .........................................................................................................................................11
OPERATING INSTRUCTIONSSECTION 4 - ...........................................................................12
4.1 CONTROLS AND INSTRUMENT IDENTIFICATION ................................................................................12
4.2 SAFETY INTERLOCk SYSTEM ................................................................................................................13
4.3 INITIAL RUN-IN PROCEDURES ................................................................................................................14
4.4 STARTING THE ENGINE ...........................................................................................................................14
4.5 GROUND TRAvEL AND STEERING .........................................................................................................14
4.6 ENGAGING THE DECk DRIvE (CUTTER BLADES) ................................................................................15
4.7 HILLSIDE OPERATION ..............................................................................................................................16
4.8 PARkING THE MOWER .............................................................................................................................16
4.9 AFTER OPERATION ..................................................................................................................................16
4.10 REMOvING CLOGGED MATERIAL ........................................................................................................16
4.11 MOvING MOWER WITH ENGINE STOPPED ..........................................................................................17
4.12 RECOMMENDATIONS FOR MOWING ....................................................................................................17
4.13 ADJUSTING CUTTING HEIGHT ..............................................................................................................17
4.14 ADJUSTING THE STEERING LEvERS ...................................................................................................18
4.15 ADJUSTING THE HEIGHT ADJUST PEDAL ..........................................................................................18
4.16 TOWING (OPTIONAL HITCH ACCESSORY)...........................................................................................19
TROUBLESHOOTING CUTTING CONDITIONSSECTION 5 - ...............................................20
I
Page 4
R
Table of Contents
ADJUSTMENTSSECTION 6 - .................................................................................................23
6.1 PARkING BRAkE ADJUSTMENT ............................................................................................................23
6.2 TRAvEL ADJUSTMENTS ..........................................................................................................................24
6.3 THROTTLE CONTROL AND CHOkE ADJUSTMENTS ............................................................................25
6.4 BELT ADJUSTMENT
6.5 BELT ALIGNMENT
6.6 CUTTER DECk ADJUSTMENTS ..............................................................................................................26
6.7 CUSTOM-CUT BAFFLE ADJUSTMENT ...................................................................................................28
MAINTENANCESECTION 7 - ..................................................................................................30
7.1 MAINTENANCE CHART - RECOMMENDED SERvICE INTERvALS ......................................................30
7.2 LUBRICATION ............................................................................................................................................31
7.3 HYDRAULIC SYSTEM ...............................................................................................................................33
7.4 ENGINE OIL ...............................................................................................................................................34
7.5 ENGINE FUEL SYSTEM ............................................................................................................................34
7.6 ENGINE AIR CLEANER .............................................................................................................................35
7.7 BATTERY ....................................................................................................................................................36
7.8 DRIvE BELTS .............................................................................................................................................37
7.9 CUTTER BLADES ......................................................................................................................................37
7.10 TIRES ........................................................................................................................................................38
7.11 CUTTER DECk GEARBOx .....................................................................................................................38
7.12 COOLING SYSTEM .................................................................................................................................39
7.13 BODY, DECk, AND UPHOLSTERY .........................................................................................................40
.................................................................................................................................25
.....................................................................................................................................26
ILLUSTRATED PARTS LISTSECTION 8 - ..............................................................................41
8.1 SCAG APPROvED ATTACHMENTS AND ACCESSORIES......................................................................41
61v CUTTER DECk .........................................................................................................................................42
CUTTER DECk CONTROLS ...........................................................................................................................44
SHEET METAL COMPONENTS
STT ROLL-OvER PROTECTION SYSTEM - WITH SUSPENSION SEAT ......................................................48
DECk DRIvE COMPONENTS .........................................................................................................................50
ENGINE & ATTACHING PARTS - 31HP-EFI kOHLER ..................................................................................52
BRAkE AND STEERING COMPONENTS ......................................................................................................54
FUEL AND HYDRAULIC SYSTEM - kOHLER 31EFI .....................................................................................56
BDP-16A HYDRAULIC PUMP ASSEMBLY WITH COOLING FAN
ELECTRICAL SYSTEM (31HP-EFI kOHLER) ................................................................................................60
REPLACEMENT DECALS AND INFORMATION PLATES
ELECTRICAL SCHEMATIC (kOHLER 31HP - EFI) ........................................................................................64
......................................................................................................................46
.................................................................58
.............................................................................62
LIMITED WARRANTY - COMMERCIAL EqUIPMENT .................................Inside Back Cover
II
Page 5
R
Section 1
SERIAL NUMBER PLATE LOCATION
R
MODEL
SERIAL
Division of Metalcraft of Mayville, Inc.
Mayville, Wisconsin 53050
Patents Issued and Pending
MANUFACTURED UNDER ONE OR MORE
OF THE FOLLOWING PATENTS:
PATENTS PENDING
4,487,006
4,885,903
4,920,733
4,967,543
4,991,382
4,998,948
5,118,617
5,826,416
5,832,708
5,865,018

GENERAL INFORMATION

INTRODUCTION1.1

Your mower was built to the highest standards in the industry. However, the prolonged life and maximum efficiency of your mower depends on you following the operating, maintenance and adjustment instructions in this manual.
If additional information or service is needed, contact your Scag Power Equipment Dealer.
We encourage you to contact your dealer for repairs. All Scag dealers are informed of the latest methods to service this equipment and provide prompt and efficient service in the field or at their service shop. They carry a full line of Scag service parts.
- IMPORTANT -
The replacement of any part on this product by other than the manufacturer's authorized replacement part may adversely affect the performance, durability or safety of this product.
USE ONLY SCAG APPROvED ATTACHMENTS AND ACCESSORIES.
Attachments and accessories manufactured by companies other than Scag Power Equipment are not approved for use on this machine. See Section 8-1.
WARNING
For pictorial clarity, some illustrations and figures in this manual may show shields, guards or plates open or removed. Under no circumstances should your mower be operated without these devices in place.
All information is based upon product information available at the time of approval for printing. Scag Power Equipment reserves the right to make changes at any time without notice and without incurring any obligation.

DIRECTION REFERENCE1.2

When ordering parts, always give the model and serial number of your mower. The serial number plate is located where shown in Figure 1-1.
Use of other than original Scag replacement parts will void the warranty.
Mower Serial Number Plate LocationFigure 1-1.
The “Right” and “Left”, “Front” and “Rear” of the machine are referenced from the operator’s right and left when seated in the normal operating position and facing the forward travel direction.
SERvICING THE ENGINE AND DRIvE 1.3
TRAIN COMPONENTS
The detail servicing and repair of the engine, hydraulic pumps and gearboxes are not covered in this manual; only routine maintenance and general service instructions are provided. For service of these components during the limited warranty period, it is important to contact your Scag dealer or find a local authorized servicing agent of the component manufacturer. Any unauthorized work done on these components during the warranty period may void your warranty.
1
Page 6
R

SYMBOLS1.4

48071S
481039S
SYMBOL DESCRIPTION SYMBOL DESCRIPTION
Choke
Transmission
Section 1
Parking Brake
On/Start
Off/Stop
Falling Hazard
Fast
Continuously Variable - Linear
Spinning Blade
Spring Tension on Idler
Oil
Thrown Object Hazard
Slow
Cutting Element - Basic Symbol
Pinch Point
Hour meter/Elapsed Operating Hours
STT MODELS
Cutting Element - Engage
Cutting Element - Disengage
CE Mark
Seat must be installed under the seat hold down bracket during installation. Failure to secure the seat under the hold down bracket could result in serious injury or death in a roll over.
Thrown Object Hazard
Read Operator's Manual
Keep Bystanders Away
2
Page 7
R
Section 2

SAFETY INFORMATION

INTRODUCTION2.1

Your mower is only as safe as the operator. Carelessness or operator error may result in serious bodily injury or death. Hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of the personnel involved in the operation, transport, maintenance and storage of the equipment. Make sure every operator is properly trained and thoroughly familiar with all of the controls before operating the mower. The owner/user can prevent and is responsible for accidents or injuries occurring to themselves, other people or property.
DANGER
The signal word “DANGER” denotes that an extremely hazardous situation exists on or near the machine that could result in high probability of death or irreparable injury if proper precautions are not taken.
WARNING
READ THIS OPERATOR’S MANUAL BEFORE ATTEMPTING TO START YOUR MOWER.
A replacement manual is available from your authorized Scag Service Dealer or by contacting Scag Power Equipment, Service Department at P.O. Box 152, Mayville, WI 53050 or contact us via the Internet at www.scag.com. The manual for this machine can be downloaded by using the model and serial number or use the contact form to make your request. Please indicate the complete model and serial number of your Scag product when requesting replacement manuals.

SIGNAL WORDS2.2

This symbol means “Attention! Become Alert! Your Safety is Involved!" The symbol is used with the following
signal words to attract your attention to safety messages found on the decals on the machine and throughout this manual. The message that follows the symbol contains important information about safety. To avoid injury and possible death, carefully read the message! Be sure to fully understand the causes of possible injury or death.
SIGNAL WORD:
The signal word “WARNING” denotes that a hazard exists on or near the machine that can result in injury or death if proper precautions are not taken.
CAUTION
The signal word “CAUTION” is a reminder of safety practices on or near the machine that could result in personal injury if proper precautions are not taken.
Your safety and the safety of others depends significantly upon your knowledge and understanding of all correct operating practices and procedures of this machine.
BEFORE OPERATION 2.3
CONSIDERATIONS
NEVER allow children to operate this riding mower. 1. Do not allow adults to operate this machine without proper instructions.
Do not mow when children and/or others are 2. present. Keep children out of the mowing area and in the watchful care of a responsible adult other than the operator. Be alert and turn machine off if a child enters the area.
DO NOT allow children to ride or play on the 3. machine, it is not a toy.
It is a distinctive word found on the safety decals on the machine and throughout this manual that alerts the viewer to the existence and relative degree of the hazard.
Clear the area to be mowed of objects that could be 4. picked up and thrown by the cutter blades.
DO NOT carry passengers.5. DO NOT operate the machine under the influence of 6.
alcohol or drugs.
3
Page 8
R
Section 2
If the operator(s) or mechanic(s) cannot read English 7. or Spanish, it is the owner's responsibility to explain this material to them.
DO NOT wear loose fitting clothing. Loose clothing,
8. jewelry or long hair could get tangled in moving parts. Do not operate the machine wearing shorts; always wear adequate protective clothing including long pants. Wearing safety glasses, safety shoes and a helmet is advisable and is required by some local ordinances and insurance regulations.
WARNING
Always wear hearing protection. Operating this machine over prolonged periods of time can cause loss of hearing.
Keep the machine and attachments in good 9. operating condition. Keep all shields and safety devices in place. If a shield, safety device or decal is defective or damaged, repair or replace it before operating the machine.
12.
DO NOT add fuel to a running or hot engine. Allow the engine to cool for several minutes before adding fuel. Never fuel indoors or inside enclosed trailers.
Keep flammable objects (cigarettes, matches, etc.), 13. open flames and sparks away from the fuel tank and fuel container. Use only approved containers.
Equipment must comply with the latest requirements 14. per SAE J137 and/or ANSI/ASAE S279 when driven on public roads.
- NOTe -
If the mower is driven on public roads, it must comply with state and local ordinances as well as SAE J137 and/or ANSI / ASAE S279 requirements. Contact your local authorities for regulations and equipment requirements.
Do not operate without the side discharge chute 15. installed and in the down position or with an optional grass catcher or mulch plate completely installed.
Check the blade mounting bolts at frequent intervals 16. for proper tightness.
Make sure all hydraulic fluid connections are tight 17. and all hydraulic hoses and lines are in good condition before starting the machine.
WARNING
This machine is equipped with an interlock system intended to protect the operator and others from injury. This is accomplished by preventing the engine from starting unless the deck drive is disengaged, the parking brake is on, the steering control levers are in the neutral position and the operator is in the seat. The system shuts off the engine if the operator leaves the seat with the deck drive engaged and/or the steering control levers are not in the neutral position and the parking brake is not engaged. Never operate equipment with the interlock system disconnected or malfunctioning.
Be sure the interlock switches are functioning 10. correctly.
Fuel is flammable; handle it with care. Fill the fuel 11. tank outdoors. Never fill it indoors. Use a funnel or spout to prevent spillage. Clean up any spillage before starting the engine.

OPERATION CONSIDERATIONS2.4

Know the function of all controls and how to stop 1. quickly.
WARNING
DO NOT operate on steep slopes. To check a slope, attempt to back up it (with the cutter deck down). If the machine can back up the slope without the wheels slipping, reduce speed and use extreme caution. Under no circumstances should the machine be operated on slopes greater than 15 degrees. ALWAYS FOLLOW OSHA APPROvED OPERATION.
Reduce speed and exercise extreme caution on 2. slopes and in sharp turns to prevent tipping or loss of control. Be especially cautious when changing directions on slopes.
4
Page 9
R
Section 2
To prevent tipping or loss of control, start and stop 3. smoothly, avoid unnecessary turns and travel at reduced speed.
When using any attachment, never direct the 4. discharge of material toward bystanders or allow anyone near the machine while in operation.
Before attempting to start the engine, with the 5. operator in the seat, disengage power to the cutter deck, place the steering control levers in the neutral position and engage the parking brake.
If the mower discharge ever plugs, shut off the 6. engine, remove the ignition key, and wait for all movement to stop before removing the obstruction.
WARNING
DO NOT use your hand to dislodge the clogged discharge chute. Use a stick or other device to remove clogged material after the engine has stopped running and the blades have stopped turning.
The machine and attachments should be stopped 15. and inspected for damage after striking a foreign object, and damage should be repaired before restarting and operating the machine.
CAUTION
Do not touch the engine or the muffler while the engine is running or immediately after stopping. These areas may be hot enough to cause a burn.
DANGER
DO NOT run the engine inside a building or a confined area without proper ventilation. Exhaust fumes are hazardous and contain carbon monoxide which can cause brain injury and death.
Be alert for holes, rocks, roots and other hidden 7. hazards in the terrain. Keep away from any drop­offs. Beware of overhead obstructions (low limbs, etc.), underground obstacles (sprinklers, pipes, tree roots, etc.). Cautiously enter a new area. Be alert for hidden hazards.
Disengage power to cutter deck before backing up. 8. Do not mow in reverse unless absolutely necessary and then only after observation of the entire area behind the mower. If you must mow in reverse, maintain a constant lookout to the rear of the machine and mow slowly.
DO NOT turn sharply. Use care when backing up.9. Disengage power to cutter deck before crossing 10.
roads, walks or gravel drives. Mow only in daylight or good artificial light.11. NEVER raise the deck with the blades engaged.12. Take all possible precautions when leaving the 13.
machine unattended, such as disengaging the mower, lowering the attachments, setting the parking brake, stopping the engine, and removing the key.
Disengage power to the attachments when 14. transporting or when not in use.
Keep hands and feet away from cutter blades and 16. moving parts. Contact can injure.
Transport the mower using a heavy duty trailer 17. or truck. Insure the trailer or truck has all of the necessary lighting and markings as required by laws, codes, and ordinances. Secure a trailer with a safety chain.
Be cautious when loading and unloading onto 18. trailers or trucks. Use only a full width ramp. Ramp angle should be no more than 15 degrees. Back up the ramp and drive down forward.
When transporting the mower, make sure the park 19. brake is engaged, the steering control levers are in the neutral position, the engine is off with the key removed, and the wheels have been blocked.
Tie the mower down securely using straps, chains, 20. cable, or ropes. Both front and rear straps must be directed down and outward from machine.
Use care when approaching blind corners, shrubs, 21. trees, or other objects that may obscure vision.
NEVER leave the machine running unattended.22.
5
Page 10
R
Section 2

ROLL-OvER PROTECTION SYSTEM2.5

WARNING
Reduce speed when turning, operating on slopes, slick or wet surfaces. Allow extra distance to stop.
Stay off of slopes too steep for safe operation. To check a slope, attempt to back up it (with the cutter deck down). If the machine can not back up the slope without the wheels slipping, do not operate the machine on this slope. Under no circumstances should the machine be operated on slopes greater than 15 degrees.
DO NOT mow near drop-offs, ditches or embankments. The machine could suddenly roll over if a wheel goes over the edge or if the edge caves in.
Any or all parts of the Roll-Over Protection System MUST NOT be removed. Failure to adhere to this guideline could result in injury or death.
FOLDABLE ROLL-OvER PROTECTION SYSTEM (IF EqUIPPED)
WARNING
keep the roll bar in the raised and locked position and the seat belt securely fastened during operation. Failure to do so could cause serious injury or loss of life.
Lower the roll bar only when absolutely necessary.
WARNING
Operate the machine smoothly, no sudden turns, starts or stops on a slope.
NEvER tow on slopes. The weight of the towed equipment may cause loss of traction and loss of control.
DO NOT permit untrained personnel to operate the machine.
Be cautious when loading and unloading onto trailers or trucks.
Use only a full width ramp.
Ramp angle should be no more than 15 degrees.
Back up the ramp and drive down forward.
This mower has been designed for good traction and stability under normal mowing conditions. However, caution must be used when traveling on slopes, especially when the grass is wet. Do not mow on wet grass. Wet grass reduces traction and steering control.
There is no roll-over protection when the roll bar is in the down position.
Lower the roll bar only when absolutely necessary.
Raise the roll bar as soon as clearance permits.
DO NOT wear the seat belt when the roll bar is in the down position.
ALWAYS wear seat belt when roll bar is in the up position.
Operate the machine smoothly, no sudden turns, starts or stops.
Check the area carefully before mowing for proper overhead clearance (i.e. branches, doorways, etc.).
DO NOT contact any overhead object with the roll bar.
To lower the roll bar, loosen the tension knob on both 1. the left hand and right hand bar. See Figure 2-1.
6
Page 11
R
Section 2
UPRIGHT AND LOCkED POSITION
TENSION kNOBS
TENSION kNOB
HAIR PIN
LOCk PIN
INSPECT WEBBING
INSPECT BUCkLE & LATCH
Remove the hairpin cotter pins and remove the two 2. (2) lock pins. See Figure 2-2.
Lower the roll bar to the down position.
3.
To raise the roll bar, lift the bar to the upright 4. position.
WARNING
Failure to properly inspect and maintain the seat belt can cause serious injury or loss of life.
Install the two (2) lock pins through the hole, secure 5. with the two (2) hairpin cotter pins and tighten the tension knobs. See Figure 2-2.
Foldable Roll-Over Protection SystemFigure 2-1.
Check the full length of the seat belt webbing for 1. cuts, wear, fraying, dirt and stiffness. See Figure 2-3.
Check the seat belt webbing in areas exposed to 2. ultra violet rays from the sun or extreme dust or dirt. If the original color of the webbing in these areas is extremely faded and/or is packed with dirt, the physical strength of this webbing may have deteriorated. If this condition exists, replace the seat belt system.
Check the buckle and latch for proper operation 3. and determine if the latch plate is excessively worn, deformed, or if the buckle is damaged or cracked. See Figure 2-3.
ROPS HingeFigure 2-2.
The potential exposure of the seat belt to severe environmental conditions make it crucial to inspect the seat belt system regularly.
It is recommended that the seat belt be inspected on a daily basis for signs of damage. Any seat belt system that shows cuts, fraying, extreme or unusual wear, significant discoloration due to UV exposure, dirt or stiffness, abrasion to the seat belt webbing, or damage to the buckle, latch plate, hardware or any other obvious problem should be replaced immediately.
Seat Belt InspectionFigure 2-3.
7
Page 12
R
MAINTENANCE CONSIDERATIONS & 2.6
STORAGE
Never make adjustments to the machine with the 1. engine running unless specifically instructed to do so. If the engine is running, keep hands, feet, and clothing away from moving parts.
Disengage drives, lower implement, set parking
2. brake, stop engine and remove key or disconnect spark plug wire to prevent accidental starting of the engine when servicing or adjusting the machine. Wait for all movement to stop before adjusting, cleaning or repairing.
Section 2
WARNING
Hydraulic fluid is under high pressure. keep body and hands away from pinholes or nozzles that eject hydraulic fluid under high pressure. If you need service on your hydraulic system, please see your authorized Scag dealer. If hydraulic fluid is injected into the skin, it must be surgically removed within a few hours by a doctor or gangrene may result.
Disconnect battery or remove spark plug wire before 3. making any repairs. Disconnect the negative terminal first and the positive last. Reconnect the positive first and the negative last.
4.
Keep all nuts, bolts and screws tight, to ensure the machine is in safe working condition. Check blade mounting bolts frequently to be sure they are tight.
Do not change the engine governor settings or 5. overspeed the engine. See the engine operator's manual for information on engine settings.
To reduce fire hazard, keep the cutting units, drives, 6. muffler and engine free of grass, leaves, excessive grease, oil and dirt.
Park the machine on level ground and engage the
7. parking brake.
8.
NEVER allow untrained personnel to service the machine.
Use care when checking blades. Use a Blade Buddy, 9. wrap the blade(s) or wear gloves and USE CAUTION when servicing blades. Only replace blades. NEVER straighten or weld blades.
Let the engine cool before storing.13. DO NOT store the machine near an open flame.14. Shut off fuel while storing or transporting.15. DO NOT store fuel near flames or drain indoors.16. Charge batteries in an open, well ventilated area, 17.
away from spark and flames. Unplug charger before connecting or disconnecting from battery. Wear protective clothing and use insulated tools.
Keep all parts in good working condition. Replace all 10. worn or damaged decals.
Use jack stands to support components when 11. required.
Carefully release pressure from components with
12. stored energy.
8
Page 13
R
Section 2
WARNING
INSTALL BELT COvER BEFORE
OPERATING MACHINE
READ OPERATOR'S MANUAL
483402
390S0150G
481568
FORWARD
REvERSE
F
R
482710
483397
483406
483407
483402
483444
483407
483397
483633
483425
483429
483300
483444

SAFETY AND INSTRUCTIONAL DECALS2.7

9
Page 14
R
Section 3

SPECIFICATIONS

ENGINE3.1

General Type ................................................................................................Heavy Duty Industrial/Commercial Gasoline
Brand .......................................................................................................................................................................Kohler
Model ..................................................................................................................Kohler Aegis LH775S (PS-LH775-0015)
Horsepower ........................................................................................................................................31HP at 3600 RPM
Type ............................................4-Cycle, Twin Cylinder, Liquid-Cooled, Electronic Fuel Injected Horizontal Shaft, OHV
Displacement ..........................................................................................................................................................748 cc.
Cylinders ..................................................................................................................................... 2 with Cast-Iron Sleeves
Valve Group ....................................................................................................................................Hydraulic Valve Lifters
Governor ........................................................................Mechanical Type with Variable Speed Control Set At 3800 RPM
Idle Speed .............................................................................................................................................1500 RPM Kohler
Fuel Pump ...................................................................................................... Electric Fuel Pump with In-Line Fuel Filter
Carburation ..................................................................................................................................Electronic Fuel Injection
Fuel ......................................................................................Non-Leaded Gasoline with a Minimum Octane Rating of 87
Oil Pump ...........................................................................................................................Full Pressure w/Full-Flow Filter
Starter ........................................................................................................................Electric Starting with Solenoid Shift
Cooling Group ..........................................................Heavy-Duty Radiator, High-Flow Engine Cooling Fan, Water Pump
Air Intake ........................................................................................................Large Capacity 2-Stage Canister Air Filter

ELECTRICAL3.2

Battery .......................................................................................... 12 volt "Maintenance Free" sealed battery (300 CCA)
Charging System ............................................................................................................................................... Alternator
Charging Output .......................................................................................................................................12 Volt, 20 Amp
System Polarity .......................................................................................................................................Negative Ground
Interlock Switches ....................................................... Seat, Neutral Control, Mower Engagement (BBC), Parking Brake
Instrument Panel ..............................................................................Volt Meter, Key Switch, Throttle Lever, BBC Switch,
Fuses and Safety Start module, Water Temperature Gauge
Fuses ........................................................................................................................................................Two (2) 20 Amp

POWER HEAD3.3

Drive System ................Hydraulic Drive with Two Variable Displacement Pumps and Two Cast-iron High Torque Motors
Hydrostatic Pumps .....................................................................Two Hydro-Gear™ 16 cc/rev. Pumps with Dump Valves
Belts .................................................................................................................Kevlar cord. Self-adjusting, Self-tightening
Drive Wheel Motors
Steering/Travel Control ...........................................................................................Twin Lever Fingertip Steering Control
with Individual Control to Each Wheel with Gas Spring Dampers
Parking Brake ...................................................................Lever Actuated Linkage to Brakes on Both Drive Wheel Axles
Wheels:
(2) Front Caster ..................................................................................................13 X 6.00 Flat-Free Semi-Pneumatic
(2) Drive .............................................................................. 24 x 12 x 12 Four-Ply Pneumatic Tubeless, Radius Edge
Tire Pressure:
Front Caster....................................................................................................................................................Flat Free
Drive
.................................................................................................................................................................. 12 PSI
Fuel Tank ......................................10-Gallon Seamless Polyethylene Tank with Large opening and Fuel Gauge Fill Cap
Seat ..................................................................................................................Padded, Thick Cushion with tall back rest
Travel Speed:
Forward ........................................................................................................................................................0-12 MPH
Reverse ..........................................................................................................................................................0-6 MPH
-NOTE- The machine will travel at 10 mph or 12 mph for transport purposes. For best cutting performance the forward travel speed should be adjusted depending upon the cutting conditions.
......................................................................Two Hydro-Gear™ 18E Cast-iron High Torque Motors
10
Page 15
R
Section 3

CUTTER DECk3.4

Type ...........................Floating, Adjustable, Anti-scalping, Hybrid Design Combines Out-front and Belly-mount Designs
Construction ............................................................................................................................Tri-plate deck construction
Top of deck consists of three steel plates totaling nearly 1/2" of steel.,7-gauge (3/16") deck skirt.
True Cutting Width ......................................................................................................................................61" (155.0 cm)
Cutting Height Adjustment ...........Foot Operated Lever Adjustment from Operator's Seat, 1.0" to 6.0" in 1/4"increments
Cutter Blades .........................................................................197 or .250 Thick, Milled Edge, Wear Resistant Marbain™
61V .............................................................................................................................................. Three (3) 21" blades
Blade Engagement ............................................................Electric Blade Engagement Clutch with Control Panel Switch
Connected to the Cutter Deck Gearbox through a Drive Shaft.
Discharge Opening ....................Extra Wide Discharge Opening with Spring Loaded Discharge Chute and Turbo Baffle
Discharge Chute ...................................................................................................Black, Polypropylene (Plastic), Flexible
Spindles ......................................Heavy-duty 1-1/8" Top Dimension Spindle Shaft, Cast Housing, Taper Roller Bearing,
Low Maintenance with Top Access Grease Fitting and Grease Overfill Relief Poppet
Spindle Pulleys ............................................................................................ Split Steel with Easily Removed Taper Hubs
Cutter Deck Belts ....................................................................B-Section with Kevlar Cord, Self-adjusting, Self-tightening
Electric Clutch Type ................................................................................................Ogura Heavy Duty PTO Clutch Brake
Drive Shaft ............................................................................................Clamp Yoke Shaft With Two High Speed U-Joints

HYDRAULIC SYSTEM3.5

Hydraulic Oil Filter ........................................................................................................ 10 Micron Spin-on Element Type
Hydraulic Reservoir .....................................................................................................................Nylon; 3 Quart Capacity

WEIGHTS AND DIMENSIONS3.6

Length........................................................................................................................................................................87.5"
Tracking Width ..............................................................................................................................................................56"
Overall Width w/chute down ......................................................................................................................................73.5"
Overall Width w/chute up ..............................................................................................................................................62"
Overall Height w/ROPS up ........................................................................................................................................67.5"
Overall Height w/ROPS down ....................................................................................................................................56.5"
Operating Weight w/ROPS ......................................................................................................................................1400#

PRODUCTIvITY3.7

Cutting Width ................................................................................................................................................................61"
Acres Per Day .............................................................................................................................................................23.7
The preceding chart will aid you in determining how many acres your Scag mower will cut per day. The chart is an estimate based on 8 hours per day cutting time at 6 MPH with a 20% allowance for overlap and turns.
11
Page 16
R

OPERATING INSTRUCTIONS

F
LEFT STEERING
CONTROL
MOWER DECK
IGNITION SWITCH
FUEL GAUGE
DUMP VALVE
DUMP VALVE
FUSES
ENGINE THROTTLE
CONTROL
RIGHT STEERING
CONTROL
DECK LIFT
DECK RELEASE
2008 STT-EFI CHMI
PARKING BRAKE
CONTROL
CUTTING HEIGHT
ADJUSTMENT
VOLT METER
SWITCH
WATER TEMPERATURE
HOUR METER
SEAT BELT
CHECK
ENGINE LIGHT
482796
SLOW
FAST
CHECK ENGINE
LIGHT
CAUTION
Do not attempt to operate this mower unless you have read this manual. Learn the location and purpose of all controls and instruments before you operate this mower.
CONTROLS AND INSTRUMENT 4.1
IDENTIFICATION
Section 4
Ignition Switch (Figure 4-1).1. The ignition switch
is used to start the engine and has three positions; OFF, ON, and START.
Mower Deck Switch (Figure 4-1).
2. Used to engage
and disengage the mower drive system. Pulling up on the switch will engage the deck drive. Pushing down on the switch will disengage the deck drive.
Engine Throttle Control (Figure 4-1).3. Used to control the engine speed. Pushing the lever forward increases engine speed. Pulling the lever back decreases engine speed. Full back position is the IDLE position. Full forward is the cutting position.
Before operating the mower, familiarize yourself with all mower and engine controls. Knowing the location, function and operation of these controls is important for safe and efficient operation of the mower.
volt Meter (Figure 4-1).4. Indicates the condition of the charging system. When the engine is running the needle should be toward the positive end of the meter. If the needle is toward the negative end of the meter, this indicates a discharge condition and the machine should be taken in for service.
Controls and InstrumentsFigure 4-1.
12
Page 17
R
Section 4
390S141-1
DUMP VALVE CONTROL
Hourmeter (Figure 4-1).5. Indicates the number of hours the engine has been operated. It only operates when the engine is running. Has preset maintenance reminders for engine and hydraulic system oil changes. Will start flashing scheduled maintenance 2 hours before preset time and continue flashing until 2 hours after. Automatically resets.
Fuse Holders (Figure 4-1).
6. Two 20-amp fuses
protect the mower’s electrical system. To replace fuses, pull fuse out of the socket and install a new fuse.
7. Used to control
Left Steering Control (Figure 4-1).
the mower's left wheel when traveling forward or reverse.
Right Steering Control (Figure 4-1).
8. Used to
control the mower's right wheel when traveling forward or reverse.
9. Used to
Parking Brake Control (Figure 4-1).
engage and disengage the parking brakes. Pull the lever back to engage the parking brakes. Push the lever forward to disengage the parking brakes.
Fuel Tank Gauge (Figure 4-1). 10. Indicates the amount of fuel in the fuel tank.
Dump valve Control Levers (Figure 4-2). 11. Located on the hydraulic pumps, used to “free-wheel” the mower. Rotating the levers clockwise until they stop allows the unit to move under hydraulic power. The levers must be in this position and torqued to 10 lb-ft during operation of the mower. Rotating the levers counter-clockwise allows the mower to be moved by hand (free-wheeling).
Cutting Height Adjustment (Figure 4-1).13. Used to set the cutter deck at the desired cutting height.
Deck Release Lever (Figure 4-1). 14. Used to lock the cutter deck in the transport position. Push the foot pedal forward and pull back on the release lever to release the cutter deck for normal mowing.
Temperature Gauge (Figure 4-1).
15. Indicates the
operating temperature of the engine. Used on mowers with the liquid-cooled engine only.
Check Engine Light (Figure 4-1).16. Indicates the operation of the Kohler Electric Fuel Injection (EFI). If a problem occurs with the engine, the light will flash a code. See your authorized Scag Dealer for diagnosis and repair.
17. Used to secure the operator.
Seat Belt (Figure 4-1).
Seat belt must be worn at all times when the ROPS is in the upright and locked position.
Seat Hold Down Release Latch (Figure 4-1).18. Located behind the seat. Used to secure the seat in the operator's position. Release the latch to gain access under the seat.

SAFETY INTERLOCk SYSTEM4.2

The mower is equipped with a safety interlock system that prevents the engine from starting unless the deck drive is disengaged, the parking brake is engaged, the steering control levers are in the neutral position and the operator is in the seat. The interlock system shuts off the engine if the operator leaves the seat with the steering control levers not in the neutral position and/or the cutter blades engaged and the parking brake not engaged.
Dump Valve ControlFigure 4-2.
Deck Lift Foot Lever (Figure 4-1). 12. Used to raise and lower the cutter deck. Push full forward to lock in the transport position.
WARNING
Never operate the mower with the interlock system disconnected or malfunctioning. Do not disengage or bypass any switch; injury to yourself and others or property damage could result.
13
Page 18
R
Section 4
9.

INITIAL RUN-IN PROCEDURES4.3

Allow engine to warm before operating the mower.
FIRST DAY OF USE OR APPROxIMATELY 10 HOURS
Check all belts for proper alignment and wear at 2, 4 1. and 8 hours.
Change the engine oil and oil filter after the first 20 2. hours of operation. (See Section 7.4.)
Check hydraulic oil level in reservoir. (See Section 3.
7.3.) Check for loose hardware. Tighten as needed.
4. Check interlock system for proper operation. (See 5.
Section 4.2.)
6.
Check tire pressure. Adjust pressure if necessary. (See Section 7.10.)

STARTING THE ENGINE4.4

CAUTION
DO NOT USE STARTING FLUIDS. Use of starting fluids in the air intake system may be potentially explosive or cause a “runaway” engine condition that could result in engine damage and/or personal injury.
Be sure the fuel shutoff valve, located behind the 1. operator's seat, is fully open. (See Section 7.5.)
2.
Secure the ROPS in the upright and locked position. Sit in the operator’s seat, fasten seat belt and place 3.
the steering control levers in the neutral position.

GROUND TRAvEL AND STEERING4.5

- IMPORTANT -
If you are not familiar with the operation of a machine with lever steering and/or hydrostatic transmissions, the steering and ground speed operations should be learned and practiced in an open area, away from buildings, fences, or obstructions.
Learn the operation on flat ground before operating on slopes.
Start practicing with a slow engine speed and slow forward travel.
Learn to feather the steering controls to obtain a smooth operating action.
Practice operating the mower until you are comfortable with the controls before proceeding to mow.
FORWARD TRAvEL
To travel forward with the mower, disengage the parking brake, pull levers inward out of the neutral lock position and slowly push the steering control levers forward an equal distance. The further the steering control levers are pushed forward the greater the forward speed will be. To increase the speed, push the steering control levers further forward and to decrease the speed, pull the steering control levers back.
To stop the forward travel, pull the steering control levers back to the neutral position.
Engage the parking brake.4. Place the PTO switch in the disengaged position.5. If the engine is cold, choke the engine as needed.6. Move the engine throttle control to about half engine 7.
speed.
8.
Turn the ignition key to the START position and release the key as soon as the engine starts. Do not hold the key in the START position for more than 15 seconds at a time. Allow at least 60 seconds between each cranking attempt to prevent overheating of the starter motor. Prolonged cranking can damage the starter motor and shorten battery life.
To steer the mower left while traveling forward, pull the left steering lever back. The further the lever is pulled back, the quicker the mower will turn left.
To steer the mower right while traveling forward, pull the right steering control lever back. The further the lever is pulled back, the quicker the mower will turn right.
- NOTe -
Smooth operation of the steering levers will produce smooth mower operation. While learning the operation of the steering controls, keep the travel speed low.
14
Page 19
R
Section 4
390S0138
PULL UP TO ENGAGE
PUSH DOWN TO DISENGAGE
- IMPORTANT -
Do not travel forward over a curb. The mower will hang up on the curb. Raise the deck and travel backwards over the curb at a 45 degree angle. (See Section 4.1, items 12 - 14, on page 14 for cutter deck raising descriptions.)
REvERSE TRAvEL
CAUTION
Disengage power to the mower before backing up. Do not mow in reverse unless absolutely necessary and then only after observation of the entire area behind the mower.
CAUTION
To stop the reverse travel, allow the steering control levers to return to the neutral position. If the mower is to be parked, place the handles in the neutral lock position and engage the parking brake.
ENGAGING THE DECk DRIvE (CUTTER 4.6
BLADES)
Set the throttle at about 3/4 speed. Do not attempt to 1. engage the deck drive at high speed as this shortens the electric clutch life — use only moderate engine speed when engaging the deck drive.
Engage the deck drive by pulling out on the yellow 2. switch, located on the instrument panel, to the engage position. See Figure 4-3.
Before backing up, observe the rear for persons and obstructions. Clear the area before backing up. Possible injury or property damage could occur.
To travel in reverse, pull levers inward out of the neutral lock position and pull both handles back. Keep the travel speed low while traveling in reverse.
- NOTe -
The mower may not travel straight in reverse. Slight adjustments may need to be made using the steering controls.
To steer left while traveling in reverse, allow the left steering control lever to move forward. The further the control is allowed to move forward, the quicker the mower will turn left.
To steer right while traveling in reverse, allow the right steering control lever to move forward. The further the control is allowed to move forward, the quicker the mower will turn right.
Cutter engage SwitchFigure 4-3.
- NOTe -
A squealing noise may be heard when engaging or disengaging the deck drive. It is caused by the electric clutch plates meshing as the mower comes up to speed. This is normal.
To disengage the deck drive, push the switch in to 3. the disengage position.
Always operate the engine at full throttle to properly 4. maintain cutting speed. If the engine starts to lug down, reduce the forward speed and allow the engine to operate at maximum RPM.
15
Page 20
R
Section 4

HILLSIDE OPERATION4.7

WARNING
DO NOT operate on steep slopes. To check a slope, attempt to back up it (with the cutter deck down). If the machine can back up the slope without the wheels slipping, reduce speed and use extreme caution. Under no circumstances should the machine be operated on slopes greater than 15 degrees. ALWAYS FOLLOW OSHA APPROvED OPERATION.
This mower has been designed for good traction 1. and stability under normal mowing conditions. However, caution must be used when traveling on slopes, especially when the grass is wet. Wet grass reduces traction and steering control. The Roll-Over Protection System is standard equipment for this machine. See Section 2.5, page 6 of this manual for further details.

AFTER OPERATION4.9

Wash the entire mower after each use. Do not 1. use high pressure spray or direct the spray onto electrical components.
- IMPORTANT -
Do not wash a hot or running engine. Cold water will damage the engine. Use compressed air to clean the engine if it is hot.
Keep the entire mower clean to inhibit serious heat
2. damage to the engine or hydraulic oil circuit.
Check the drive belts for proper alignment and any 3. signs of wear. Correct and adjust if necessary.
DANGER
To avoid injury from burns, allow the mower to cool before removing the fuel tank cap and refueling.
To prevent tipping or loss of control, do not start or 2. stop suddenly, avoid unnecessary turns and travel at reduced speed. If tires loose traction, disengage blades and proceed slowly off the slope.
Avoid sudden starts when mowing uphill. Sudden 3. starts may cause the machine to tip backwards.
Loss of traction may occur when traveling down hill.
4. Weight transfers to the front of the machine and may cause the drive wheels to slip causing loss of braking or steering.
5.
Keep tires properly inflated.

PARkING THE MOWER4.8

Park the machine on a flat, level surface only. Do not 1. park the machine on an incline.
Place the steering control levers in the neutral
2. position.
Disengage the cutter blades.3. Slow the engine to idle speed.4. Engage the parking brake.5.
4.
After the mower has cooled down, fill the fuel tank with fresh, clean fuel at the end of every day of operation. See Engine Owner's Manual for proper octane requirements.
Check the tire pressure. Adjust pressure if 5. necessary.

REMOvING CLOGGED MATERIAL4.10

DANGER
ROTATING BLADES
NEvER PUT YOUR HANDS INTO THE DISCHARGE CHUTE FOR ANY REASON!
Shut off the engine and remove the key and only then use a stick or similar object to remove material if clogging has occurred.
Turn the ignition key to the OFF position and remove 6. the key.
16
1.
If the discharge chute becomes clogged, shut off the engine and remove the ignition key. Using a stick or similar item, dislodge the clogged material. Then resume normal mowing.
Page 21
R
Section 4
390S141-1
DUMP VALVE CONTROL
CUTTING
HEIGHT
6
5.5
5
4.5
4
3.5
3
2.5
2
1.5
1
4
8
15
4
3
390S0140-2
HEIGHT ADJUSTMENT PEDAL
LANYARD PIN
MOvING MOWER WITH ENGINE 4.11
STOPPED
To “free-wheel” or move the mower around without the engine running, rotate the dump valve levers counter­clockwise. See Figure 4-4. Disengage the parking brake and move the mower by hand. When the machine is in the desired position, engage the parking brake and rotate the levers clockwise until they stop. The dump valve levers must be returned to the DRIVE position and torqued to 10 lb-ft to drive the mower.
4.
Keep mower and discharge chute clean. When mowing wet or tall grass, mow the grass twice. 5.
Raise the mower to the highest setting for the first pass and then make a second pass to the desired height.
Use a slow travel speed for trimming purposes.6. Operate the engine at full throttle for best cutting. 7.
Mowing with a lower RPM causes the mower to tear the grass. The engine is designed to be operated at full speed.
Use the alternate stripe pattern for best lawn 8. appearance. Vary the direction of the stripe each time the grass is mowed to avoid wear patterns in the grass.

ADJUSTING CUTTING HEIGHT4.13

The mower deck can be adjusted from a height of 1.0 inch to 6.0 inches at 1/4-inch intervals. To adjust the cutting height:
Dump Valve ControlFigure 4-4.

RECOMMENDATIONS FOR MOWING4.12

Do not mow with dull blades. A dull blade will tear 1. grass, resulting in poor lawn appearance and reduced mowing power.
WARNING
DO NOT operate without Discharge Chute, Mulching kit, or entire Grass Catcher properly installed.
The discharge chute must not be removed and 2. must be kept in the lowest position to deflect grass clippings and thrown objects downward. Direct the side discharge away from sidewalks or streets to minimize cleanup of clippings. When mowing close to obstacles, direct the discharge away from the obstacles to reduce the chance of property damage by thrown objects.
WARNING
DO NOT adjust the cutting height with the mower blades rotating. Disengage the power to the cutter blades and then adjust cutting height.
1.
Disengage the power to the cutter blades. Push the cutting height adjustment foot pedal all 2.
the way forward using your right foot until it locks in place. See Figure 4-5.
Cut grass when it is dry and not too tall. Do not cut 3. grass too short (cut off 1/3 or less of existing grass for best appearance). Mow frequently.
Adjusting Cutting HeightFigure 4-5.
17
Page 22
R
Insert the lanyard pin into the cutting height index at 3.
CUTTING
HEIGHT
6
5.5
5
4.5
4
3.5
3
2.5
2
1.5
1
481543
390S0151-1
DECK RELEASE LEVER
TENSION kNOB
TENSION kNOB
ROTATE LEvER
CUTTING
HEIGHT
6
5.5
5
4.5
4
3.5
3
2.5
2
1.5
1
481
54
3
390S0140-2
HEIGHT ADJUSTMENT PEDAL LOCATIONS
the desired cutting height. Push forward on the deck lift foot lever, hold in place and pull back on the deck release lever. See Figure 4-6. Slowly release the foot pedal. A deck height decal is located on the cutting height index as an aid in adjusting the deck to the desired height. See Figure 4-5.
Section 4
Adjusting Steering LeversFigure 4-7.
4.
The control handle can also be adjusted in two different positions. If necessary, remove the two bolts securing the control handle to the control lever. Install the handle in the desired position.
Deck Release LeverFigure 4-6.

ADJUSTING THE STEERING LEvERS4.14

Position the seat to the desired location.1. While in the operator's position without the engine 2.
running, move both steering levers forward and reverse to check for full function control and comfort.
If adjustment of the steering levers is needed, use 3. the following instructions to adjust.
A. Loosen the tension knob on the lever assembly.
B. Rotate the steering lever forward or backward to achieve the optimum operating position.
C. Tighten the tension knob and repeat on the opposite side.
D. While in the operator's position, bring the steering levers out of the neutral lock position and check to make sure both levers are even before operating.
ADJUSTING THE HEIGHT ADJUST 4.15
PEDAL
Position the seat to the desired location.1. While in the operator's position with out the engine 2.
running, push down on the height adjust pedal to check for full function control.
The height adjust pedal can be located in three (3) 3. different positions for operator comfort and control. See Figure 4-8.
Height Adjust Pedal LocationsFigure 4-8.
18
Page 23
R
Section 4
TOWING (OPTIONAL HITCH 4.16
ACCESSORY)
NEVER allow children or others in or on towed 1. equipment.
Tow only with a machine that has a hitch designed
2.
for towing. Do not attach towed equipment except at the hitch point.
Follow manufacturer's recommendations for weight 3. limit for towed equipment. 250 lbs. maximum towing weight.
4.
NEVER tow on slopes. The weight of the towed equipment may cause loss of traction and loss of control.
Travel slowly and allow extra distance to stop.5. Zero-turning with a trailer attached could cause 6.
damage to the trailer or mower.
19
Page 24
R
Width of Deck
SGB020
Width of Deck
SGB018
Width
of
Deck
Width
of
Deck
SGB019

TROUBLESHOOTING CUTTING CONDITIONS

CONDITION CAUSE CURE
Section 5
STRINGERS - OCCASIONAL BLADES OF UNCUT GRASS
STREAkING - STRIPS OF UNCUT GRASS IN CUTTING PATH
Low engine RPM Run engine at full RPM
Ground speed too fast Slow speed to adjust for conditions
Wet grass Cut grass after it has dried out
Dull blades, incorrect sharpening Sharpen blades
Deck plugged, grass accumulation Clean underside of deck
Belts slipping Adjust belt tension
Dull, worn blades Sharpen blades
Incorrect blade sharpening Sharpen blades
Low engine RPM Run engine at full RPM
Belt slipping Adjust belt tension
Deck plugged, grass accumulation Clean underside of deck
STREAkING - STRIPS OF UNCUT GRASS BETWEEN CUTTING PATHS
Ground speed too fast Slow speed to adjust for conditions
Wet grass Cut grass after it has dried out
Bent blades Replace blades
Not enough overlapping between rows Increase the overlap of each pass
20
Page 25
R
Section 5
Width of Deck
SGB020
Width of Deck
SGB021
Width of Deck
SGB023
TROUBLESHOOTING CUTTING CONDITIONS (CONT'D)
CONDITION CAUSE CURE
UNEvEN CU T O N FLAT GROUND - WAvY HIGH-LOW APPEARANCE, SCALLOPED CUT, OR ROUGH CONTOUR
UNEvEN CUT ON UNEvEN GROUND - WA vY APPEARANCE, HIGH-LOW SCALLOPED CUT, OR ROUGH CONTOUR
Lift worn from blade Replace blade
Blade upside down Mount with cutting edge toward ground
Deck plugged, grass accumulation Clean underside of deck
Too much blade angle (deck pitch) Adjust pitch and level
Deck mounted improperly See your authorized SCAG dealer
Bent spindle area See your authorized SCAG dealer
Dull blade Sharpen blade
May need to reduce ground speed, raise
Uneven ground
cutting height, and/or change direction of cut
SLOPING RIDGE ACROSS WIDTH OF CUTTING PATH
Tire pressures not equal Check and adjust tire pressure
Wheels uneven Check and adjust tire pressure
Deck mounted incorrectly See your authorized SCAG dealer
Deck not level side-to side Check for level and correct
21
Page 26
R
Width of Deck
SGB022
Width of Deck
SGB024
Width of Deck
SGB025
TROUBLESHOOTING CUTTING CONDITIONS (CONT'D)
CONDITION CAUSE CURE
Section 5
SCALPING - BLADES HITTING DIRT OR CUTTING vERY CLOSE TO THE GROUND
STEP CUT - RIDGE IN CENTER OF CUTTING PATH
Low tire pressures Check and adjust pressures
Ground speed too fast Slow speed to adjust for conditions
May need to reduce ground speed, raise
Cutting too low
cutting height, change direction of cut, and/or change pitch and level
May need to reduce ground speed, raise
Rough terrain
cutting height, and/or change direction of cut
Ground speed too fast Slow speed to adjust for conditions
Wet grass Cut grass after it has dried out
Blades not mounted evenly Adjust pitch and level
Bent blade Replace blade
Internal spindle failure See your authorized SCAG dealer
SLOPE CUT - SLOPING RIDGES ACROSS WIDTH OF CUTTING PATH
Mounting of spindle incorrect See your authorized SCAG dealer
Bent spindle mounting area See your authorized SCAG dealer
Internal spindle failure See your authorized SCAG dealer
Bent deck housing See your authorized SCAG dealer
22
Page 27
R
Section 6
390S0152-1
LOOSEN HERE
2" to 2-1/4" Clearance
1-7/16”
LOOSEN HERE
ADJUST HERE

ADJUSTMENTS

PARkING BRAkE ADJUSTMENT6.1

WARNING
Do not operate the mower if the parking brake is not operable. Possible severe injury could result.
The parking brake linkage should be adjusted whenever the parking brake lever is placed in the “ENGAGE” position and the parking brake will allow the mower to move. If the following procedures do not allow you to engage the parking brake properly, contact your Scag dealer for further brake adjustments.
Position a floor jack under the rear of the machine. 1. Raise the machine and support it to prevent it from falling. Block the caster wheels to prevent the machine from moving. Remove the drive wheels.
With the brake lever in the disengaged position,
2. check the distance between the top of the frame tube and the bottom of the brake handle. The distance should be 2" to 2-1/4" (See Figure 6-1).
- NOTe -
If this procedure does not achieve proper brake adjustment, please contact your authorized Scag dealer.
Brake AdjustmentFigure 6-1.
If the distance is not at the specified measurement, 3. adjust by loosening the jam nuts at both ends of the brake control rod and turning the rod until the proper distance is achieved. (See Figure 6-1). Tighten the jam nuts.
4.
With the brake in the engaged position, check the spring compression between the two flat washers on the LH side of the machine. The distance should be 1-7/16". (See Figure 6-2).
If the distance is not at the specified measurement,
5. loosen the jam nut at the rod end side of the brake actuator rod. (See Figure 6-2).
Turn the adjustment bolt (clockwise to decrease 6. the spring compression or counter clockwise to increase the spring compression) until the 1-7/16" measurement is achieved and tighten the jam nut. (See Figure 6-2).
Repeat steps 4 though 6 on the RH side of the 7. machine.
Replace the drive wheels and test the brake.8.
Brake Rod AdjustmentFigure 6-2.
23
Page 28
R

TRAvEL ADJUSTMENTS6.2

390S0149
CONTROL
ROD
LOOSEN
HERE
STT99RHCRA
LOOSEN HERE
ADJUST HERE
390S0147
LOOSEN
HERE
390S0146
LOOSEN HERE
ADJUST HERE
Neutral or tracking adjustments will need to be made if:
A. The steering control levers are in the neutral position and the machine creeps forward or backward. (Neutral Adjustment, See Page 26).
B. The steering control levers are in the full forward position and the mower pulls to one side or the other when traveling in a forward direction. (Tracking Adjustment, See Page 27).
NEUTRAL ADJUSTMENT
Section 6
Be sure the dump valve levers are in the run position 1. and the steering control levers are in the neutral lock position.
2.
With an operator in the seat, start the engine and disengage the parking brake.
Run the engine at full operating speed and check if 3. the machine creeps forward or backwards.
Adjust the RH wheel by loosening the jam nuts on 4. the steering control rod and turning the rod until the drive wheel turns in the forward direction. Turn the rod back until the drive wheel stops moving. Turn the rod an additional 1/2 turn. (See Figure 6-3).
RH Steering Control Rod AdjustmentFigure 6-3.
Tighten the jam nuts and repeat for the LH wheel. 5. (See Figure 6-4).
LH Steering Control Rod AdjustmentFigure 6-4.
24
Page 29
R
Section 6
Actuate the steering control levers forward and 6. reverse several times and return them to the neutral position.
Check that the drive wheels remained in neutral and
7. readjust if necessary.
Check that the steering control levers hit the stop 8. before the pumps reach full stroke. Adjust as needed.
TRACkING ADJUSTMENT
CAUTION
Stop the engine and remove the key from the ignition before making any adjustments. Wait for all moving parts to come to a complete stop before beginning work.
- NOTe -
If after making the adjustment as outlined in step 1A, the machine creeps forward or backward, the neutral adjustment must be made as described on page 26.
2.
If at full speed the mower pulls left, it is an indication that the right wheel is turning faster than the left wheel. To adjust this condition, proceed as follows:
A. Stop the machine and place the steering control levers in the neutral position. Loosen the lock nuts securing the ball joints at each end of the RH steering control rod. Rotate the control rod to lengthen the rod and tighten the lock nuts. This will cause the control rod to stroke the RH pump less, slowing down the RH
wheel. (See Figure 6-3, page 26)
- NOTe -
If after making the adjustment as outlined in step 2A, the machine creeps forward or backward, the neutral adjustment must be made as described on page 26.
CAUTION
The engine and drive unit can get hot during operation causing burn injuries. Allow engine and drive components to cool before making any adjustments.
- NOTe -
Before proceeding with this adjustment, be sure that the caster wheels turn plus pivot freely and that the tire pressure in the drive wheels is correct. If the tire pressure is not correct, the machine will pull to the side with the lower pressure.
If at full speed the mower pulls right, it is an
1. indication that the left wheel is turning faster than the right wheel. To adjust this condition, proceed as follows:
A. Stop the machine and place the steering control levers in the neutral position. Loosen the lock nuts securing the ball joints at each end of the LH steering control rod. Rotate the control rod to lengthen the rod and tighten the lock nuts. This will cause the control rod to stroke the LH pump less, slowing down the LH wheel. (See Figure 6-4, page 26)
THROTTLE CONTROL AND CHOkE 6.3
ADJUSTMENTS
These adjustments must be performed by your Scag dealer to ensure proper and efficient running of the engine. Should either need adjustment, contact your authorized Scag service center.

BELT ADJUSTMENT6.4

WARNING
Before removing any guards, shut the engine off and remove the ignition key.
All drive belts and cutter deck belts are spring loaded and self-tensioning. The springs should be checked periodically
for proper alignment and wear.
25
Page 30
R

BELT ALIGNMENT6.5

LOOSEN HERE
ADJUST HERE
390S0174-1
JAM NUT ADJUST HERE
Belt alignment is important for proper performance of your Scag mower. If you experience frequent belt wear or breakage, see your authorized Scag service center for belt adjustment.
Section 6
2.
Loosen the two (2) elastic stop nuts. Adjust the bolt up or down on the adjustment bracket to adjust the cutter deck until the distance from the bottom of the cutter deck to the floor is the same as the measurement on the RH side of the machine.
Tighten the two elastic stop nuts to secure the cutter
3. deck in the proper position.

CUTTER DECk ADJUSTMENTS6.6

Cutter deck level, pitch and height are set at the factory. However, if these adjustments should ever need to be made, the following procedures will aid in obtaining the proper cutter deck adjustment.
- NOTe -
Before proceeding with the cutter deck adjustments, be sure that all tires are properly inflated.
CUTTER DECk LEvEL
The cutter deck should be level from side-to-side for proper cutting performance. To check for level, be sure that the mower is on a flat, level surface, the tires are properly inflated and the cutter deck is set at the most common cutting height that you will use. On the RH side of the machine, check the distance from the bottom of the cutter deck to the floor. Next check the distance from the bottom of the cutter deck to the floor on the LH side of the machine. Both measurements should be the same. If the two measurements are different, the cutter deck level must be adjusted as follows:
CUTTER DECk PITCH
The pitch of the cutter deck should be equal between the front and rear of the cutter deck for proper cutting performance. To check for proper deck pitch, be sure that the mower is on a flat, level surface and the tires are properly inflated.
Check the distance from the bottom of the cutter deck to the floor at the rear RH side of the cutter deck directly behind the cutter deck hanging chains. Next check the distance from the bottom of the cutter deck to the floor at the front RH side of the cutter deck directly in front of the cutter deck hanging chains. The measurement at the front of the cutter deck should be equal to the measurement at the rear of the deck. Make these measurements at the LH side of the cutter deck also. If the measurement at the front of the deck is not equal, the cutter deck pitch must
be adjusted as follows:
1.
Loosen the jam nut on both adjusting rods. (See Figure 6.6)
On the front LH side of the cutter deck locate the 1. cutter deck level adjusting bracket (See Figure 6.5)
Cutter Deck Level AdjustmentFigure 6-5.
Cutter Deck Level AdjustmentFigure 6-6.
Using a wrench on the jam nut (See Figure 6.6) turn 2. the adjusting rods until the proper pitch is obtained on both the RH and the LH side of the cutter deck. Tighten both jam nuts.
26
Page 31
R
Section 6
390S014A-2
CUTTING
HEIGHT
6
5.5
5
4.5
4
3.5
3
2.5
2
1.5
1
4
81
5
43
HEIGHT ADJUSTMENT PEDAL
LANYARD PIN
LOOSEN HERE
1/4"
DECK STOP
390S0175-1
- NOTe -
To prevent the cutter deck from teetering, all four (4) cutter deck hanging chains must have tension on them. If all four chains do not have tension on them and the deck teeters, you must readjust the cutter deck as outlined in the procedures above.
CUTTER DECk HEIGHT
The cutter deck height adjustment is made to ensure that the cutter deck is cutting at the height indicated on the cutting height index gauge. To check for proper deck height, be sure that the mower is on a flat, level surface and the
tires are properly inflated.
Place the cutter deck in the transport position. 1. Loosen the jam nuts on both ends of the deck height control rod. (See Figure 6.7)
Cutter Deck StopFigure 6-8.
Check the cutter deck cutting height by placing the 3. lanyard pin in the 3" position on the cutting height index. Release the deck from the transport position and allow the deck to move to the 3" cutting height position.
Turn the control rod (See Figure 6.7) until there is a 2. 1/4" space between the rear deck stop and the top of the cutter deck. (See Figure 6.8). Tighten the jam nuts on the control rod.
Cutter Deck Height AdjustmentFigure 6-7.
Check the measurement from the floor to the 4. cutter blade tip. If the measurement is not at 3", an adjustment can be made using the deck height control rod. (See Figure 6.7)
- NOTe -
If an adjustment had to be made, be sure that the cutter deck can easily be locked into the transport position.
27
Page 32
R
Section 6

CUSTOM-CUT BAFFLE ADJUSTMENT6.7

The Custom-Cut Baffle is designed to deliver optimum airflow and superior cutting performance in any type of grass. The Custom-Cut Baffle can be raised or lowered to precisely tailor the deck's performance for the type of grass being cut. The baffle can be set in three (3) (early models), or seven (7) (current production) different positions for optimum performance.
3-POSITION CUSTOM-CUT BAFFLE ADJUSTMENT - EARLY MODELS
A. 3" Position - (See Figure 6-9). Baffle is installed using the top set of holes on the front baffle welded inside the cutter deck. In this position the Velocity-Plus cutter deck will deliver the best quality-of-cut in very tall, wiry, tough to cut grass.
B. 3-1/2" Position - (See Figure 6-9). Baffle is installed using the middle set of holes on the front baffle welded inside the cutter deck. Can be used for general purpose cutting. Placing the Custom-Cut Baffle in the 3-1/2" position gives a good mix of cutting performance in all types of grass.
C. 4" Position (factory setting) - (See Figure 6-9). Baffle is installed using the bottom set of holes on the front baffle welded inside the cutter deck. Placing the baffle in the 4" setting will enhance fall cutting (leaf pickup) and reduce cutter deck "blowout".
To adjust the Custom-Cut Baffle height:
7-POSITION CUSTOM-CUT BAFFLE ADJUSTMENT - CURRENT PRODUCTION
A. 3-1/2" or 3-3/4" Position - (See Figure 6-10). For very tall, wiry or tough-to-cut grass.
B. 4" (factory setting), 4-1/4" or 4-1/2" Position - (See Figure 6-10). For general purpose cutting. This gives the best mix of cutting performance in all types of grass.
C. 4-3/4" or 5-1/4" Position - (See Figure 6-10). Placing the baffle in either the 4-3/4" or 5-1/4" setting will enhance fall cutting (leaf pickup) and reduce cutter deck "blowout".
To adjust the Custom-Cut Baffle height:
Place the cutter deck in the transport position.1. Remove the hardware securing the Custom-Cut 2.
Baffle to the cutter deck.
- NOTe -
Hardware location used in the illustrations are for reference only. Location of hardware may vary depending on cutter deck size.
Move the Custom-Cut Baffle to desired position. See 3. Figure 6-10.
Reinstall the mounting hardware. Torque hardware to 4. 39 lb-ft.
Place the cutter deck in the transport position.1. Remove the hardware securing the Custom-Cut 2.
Baffle to the cutter deck. See Figure 6-9.
- NOTe -
Hardware location used in the illustrations are for reference only. Location of hardware may vary depending on cutter deck size.
Move the Custom-Cut Baffle to desired position. See 3. Figure 6-9.
Reinstall the mounting hardware as shown. Torque 4. hardware to 39 lb-ft.
28
Page 33
R
Section 6
Slot “A” Hole 1 Hole 2 Hole 3 Height (inches) 3” 3-1/2” 4”
Custom-Cut Baffle Adjustment
Mounting Slot Mounting Hardware Location
1
2
3
A
1
2
3
A
1
2
3
4
A B
1
2
3
4
A
B
Custom-Cut Baffle Adjustment
Mounting Slot Selected Mounting Hardware Location
Slot “A” Hole 1 Hole 2 Hole 3 Hole 4 Height (inches) 3-3/4” 4-1/4” 4-3/4” 5-1/4”
Slot “B” Hole 2 Hole 3 Hole 4 Height (inches) 3-1/2” 4” 4-1/2”
3-Position Custom-Cut Baffle AdjustmentFigure 6-9.
7-Position Custom-Cut Baffle AdjustmentFigure 6-10.
29
Page 34
R

MAINTENANCE CHART - RECOMMENDED SERvICE INTERvALS7.1

BREAk-IN (FIRST 10)
X
Section 7

MAINTENANCE

HOURS
PROCEDURE COMMENTS
8 40 100 200 500
Check all hardware for tightness
X
X
X X
X
X X X X X
X
X
X
Check hydraulic oil level See paragraph 7.3 Che ck all belts for proper
alignment Change engine oil and filter See paragraph 7.4
Check coolant level See paragraph 7.11 Check hydraulic hoses for leaks Use extreme caution when
Check engine oil level See paragraph 7.4 *Clean mower See paragraph 7.12 Check condition of blades See paragraph 7.9 Apply grease to fittings See paragraph 7.2 Check tire pressure See paragraph 7.10 Inspect seat belt for wear or
damage Check the operator interlock
system Check coolant level See paragraph 7.11
See paragraph 7.8
checking the hydraulic hoses. See paragraph 2.6
See paragraph 2.5
See paragraph 4.2
X
X
X X X
X
* Perform these maintenance procedures more frequently under extreme dusty or dirty conditions
Check battery electrolyte level clean battery posts and cables
Check belts for proper alignment See paragraph 7.8
Apply grease to fittings See paragraph 7.2 Change engine oil See paragraph 7.4 *Clean air cleaner element See paragraph 7.6 Check lubricant in cutter deck
gearbox
See paragraph 7.7
See paragraph 7.11
30
Page 35
R
Section 7
MAINTENANCE CHART - RECOMMENDED SERvICE INTERvALS (CONT'D)
HOURS
BREAk-IN (FIRST 10)
8 40 100 200 500
X
Apply grease to fittings See paragraph 7.2
PROCEDURE COMMENTS
X X X
Check hardware for tightness Change engine oil filter See paragraph 7.4 Check hydraulic oil level See paragraph 7.3 Replace engine fuel filter See paragraph 7.5
X
Drain hydraulic system and replace
X
hydraulic oil Replace hydraulic oil filter See paragraph 7.3
X
Replace cutter deck gearbox
X
lubricant Change coolant See paragraph 7.11
X
Use SAE 20W50 Motor Oil. See paragraph 7.3
See paragraph 7.11

LUBRICATION7.2

GREASE FITTING LUBRICATION CHART (SEE FIGURE 7-1)
LOCATION LUBRICATION INTERvAL LUBRICANT
1 Caster Wheel Pivot * 500 Hours/Yearly Chassis Grease 2 2 Caster Wheel Bearings 100 Hours/Monthly Chassis Grease 2 3 Cutter Deck Bellcranks 100 Hours/Bi-Weekly Chassis Grease 4 4 Cutter Deck Pusharms 100 Hours/Bi-Weekly Chassis Grease 2 5 PTO Spindle 40 Hours/Weekly +Lithium MP White Grease 2125 1 6 Cutter Deck Spindle 40 Hours/Weekly +Lithium MP White Grease 2125 3 7 Brake Handle 200 Hours/Monthly Chassis Grease 1 8 Cutter Deck Drive Shaft U-Joints 200 Hours/Monthly Chassis Grease 2 9 Cutter Deck Drive Shaft Slip Sleeve 40 Hours/Weekly Chassis Grease 1
NO. OF
PLACES
+ Compatible Greases: Mobilix #2 found at Mobil Service Stations Ronex MP found at Exxon Service Stations Super Lube MEP #2 & Super Stay-M #2 found at Conoco Stations Shell Alvania #2 found at Shell Service Stations Lidok EP #2 found at industrial shops Timken Lithium Multi-Use #2 found at industrial shops
* PROCEDURE: Remove grease cap, part number 481559. Remove plug, part number 482028-01, and install grease zerk. Apply grease to the fitting until new grease appears at the top of the caster extension. Remove the grease zerk and reinstall the plug. Reinstall the grease cap. Special tool, part number 47007, is recommended for use in the installation of the grease cap.
31
Page 36
R
Section 7
GREASE FITTING LUBRICATION
LUBRICANT / INTERVAL
LITHIUM MP WHITE GREASE 2125 ( 40 HOURS / WEEKLY )
CHASSIS GREASE ( 100 HOURS / BI-MONTHLY )
CHASSIS GREASE ( 200 HOURS / MONTHLY )
3
1
5
4
6
2
CHASSIS GREASE ( 500 HOURS / YEARLY )
STT-EFI Grease Points
1
7
4
8
2
9
3
8
Lubrication Fitting PointsFigure 7-1.
32
Page 37
R
Section 7
390S0155-1
HYDRAULIC OIL FILTER
Hydraulic Oil Reservoir
STT99HOR-1

HYDRAULIC SYSTEM7.3

A. CHECkING HYDRAULIC OIL LEvEL
The hydraulic oil level should be checked after the first 10 hours of operation. Thereafter, check the oil after every 200 hours of machine operation or monthly, whichever occurs first.
- IMPORTANT -
If the oil level is consistently low, check for leaks and correct immediately.
1.
Wipe dirt and contaminants from around the reservoir cap. Remove the cap from the hydraulic oil reservoir.
Visually check the level of hydraulic oil. Hydraulic 2. oil must be at least 3" inches from top of the filler neck. If the level cannot be determined visually, use a clean tape measure to check the level. If the fluid is low, add 20W50 motor oil. DO NOT overfill; (overfilling the oil reservoir may cause oil seepage around the cap area).
- IMPORTANT -
The hydraulic oil should be changed if you notice the presence of water or a rancid odor to the hydraulic oil.
1.
Park the mower on a level surface and stop the engine.
Place a suitable container under the hydraulic oil 2. filter. Remove the fill cap from the reservoir and the drain plug from the bottom of the drain tee fitting on the filter base. See Figure 7-3. Allow the fluid to drain into the container and properly discard it.
Clean the fill cap and install it onto the reservoir.3.
Hydraulic Oil ReservoirFigure 7-2.
B. CHANGING HYDRAULIC OIL
The hydraulic oil should be changed after every 500 hours or annually, whichever occurs first. The oil should also be changed if the color of the fluid has become black or milky. A black color and/or a rancid odor usually indicates possible overheating of the oil, and a milky color usually indicates water in the hydraulic oil.
Hydraulic Oil FilterFigure 7-3.
Re-install the drain plug into the tee fitting and be 3. sure it is tight.
- NOTe -
Before refilling the hydraulic oil reservoir the hydraulic oil filter should be changed as outlined in Procedure C "Changing Hydraulic Oil Filter Element" on page 34.
Fill the reservoir to 3-1/4" inches from the top of the 4. filler neck with 20W50 motor oil.
Replace the reservoir fill cap. Start the engine and 5. drive forward and backward for two minutes. Check the oil level in the reservoir. If necessary, add oil to the reservoir.
33
Page 38
R
STT99CEC
ENGINE OIL FILTER
DRAIN PLUG
C. CHANGING HYDRAULIC OIL FILTER
390S0156

ENGINE OIL

DIPSTICk
ELEMENT
The hydraulic oil filter should be changed after every 500 hours of operation or annually, whichever occurs first.
Remove the oil filter element and properly discard it. 1. See Figure 7-3. Fill the new filter with clean oil and install the filter. Hand tighten only.
Run the engine at idle speed with the speed control 2. lever in neutral for five minutes.
Check the oil level in the hydraulic tank. It must 3. be 3-1/4" inches from the top of the filler neck. If necessary, add SAE 20W50 motor oil.
Section 7
ENGINE OIL7.4
engine Oil Fill/Dipstick LocationFigure 7-4.
A. CHECkING ENGINE CRANkCASE OIL LEvEL
The engine oil level should be checked after every 8 hours of operation or daily as instructed in the Engine Operator’s Manual furnished with this mower.
B. CHANGING ENGINE CRANkCASE OIL
Drain Plug and Oil Filter LocationFigure 7-5.
C. CHANGING ENGINE OIL FILTER
After the first 20 hours of operation, replace the engine oil filter. Thereafter, replace the oil filter after every 200 hours of operation or every month, whichever occurs first. Refer to Engine Operator’s Manual for instructions. See Figure 7-5.

ENGINE FUEL SYSTEM7.5

DANGER
To avoid injury from burns, allow the mower to cool before removing the fuel tank cap and refueling.
A. FILLING THE FUEL TANk
Fill the fuel tank at the beginning of each operating day to within one (1) inch below the filler neck. Do not overfill. Use clean, fresh unleaded gasoline with a minimum octane rating of 87 and a maximum of 10% Ethanol.
After the first 20 hours of operation, change the engine crankcase oil and replace the oil filter. Thereafter, change the engine crankcase oil after every 100 hours of operation or bi-weekly, whichever occurs first. Refer to the Engine Operator’s Manual furnished with this mower for instructions. See Figure 7-5.
DO NOT use E85 Fuel. Using E85 Fuel will cause severe damage to the engine.
To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive.
34
Page 39
R
Section 7
Fuel Filter (with hose clamps above and below)
STT99FF-1
Extinguish all cigarettes, cigars, pipes and other 1. sources of ignition.
Use only an approved gasoline container.
2. Never remove the gas cap or add fuel with the 3.
engine running. Allow the engine to completely cool before fueling.
4.
Never fuel the machine indoors or in an enclosed trailer.
Never store the machine or fuel container where 5. there is an open flame, spark or pilot light such as on a water heater or other appliances.
Never fill containers inside a vehicle or on a truck 6. or trailer bed with a plastic liner. Always place containers on the ground away from your vehicle before filling.
Remove the machine from the truck or trailer and
7. fuel on the ground. If this is not possible, then refuel the machine with a portable container, rather than from a gasoline dispenser nozzle.
8.
Keep the nozzle in contact with the rim of fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device.
Install a new fuel filter. Be sure it is installed in the 3. proper direction. Secure to the fuel hose using the two clamps.
Open the fuel shut-off valve.
4.
Fuel FilterFigure 7-6.

ENGINE AIR CLEANER7.6

If fuel is spilled on clothing, change clothing 9. immediately and wash affected skin.
Replace gas cap and tighten securely.10.
B. REPLACING IN-LINE FUEL FILTER ELEMENTS
WARNING
Fuel System from the fuel pump to the engine is under high pressure. The fuel system after the fuel pump must be serviced by an Authorized Scag Power Equipment Dealer only.
The engine fuel filter should be replaced after every 500 hours of operation or annually, whichever occurs first. See Figure 7-6.
Close the shut-off valve.1. Remove the two clamps securing the fuel filter to the 2.
fuel hose. Remove the fuel filter.
A. CLEANING AND/OR REPLACING AIR CLEANER ELEMENT
For any air cleaner, the operating environment dictates the air cleaner service periods. Inspect and clean the air cleaner element after every 100 hours of operation or bi-weekly, whichever occurs first and replace the element if required. See Engine Owner's Manual for service information.
- NOTe -
In extremely dusty conditions it may be necessary to check the element once or twice daily to prevent engine damage.
Unhook the clamps securing the air cleaner cover to
1. the air filter canister. Remove the air cleaner cover and set aside.
2.
Remove the air cleaner and inspect. Clean or replace the air cleaner and foam 3.
pre-cleaner as recommended by the engine manufacturer.
Replace the air cleaner cover and be sure to snap 4. the latches closed.
35
Page 40
R
Section 7

BATTERY7.7

WARNING
Lead-acid batteries produce flammable and explosive gases. To avoid personal injury when checking, testing or charging batteries, DO NOT use smoking materials near batteries. keep arcs, sparks and flames away from batteries. Provide proper ventilation and wear safety glasses.
WARNING
Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to cause cancer and reproductive harm. Wash hands after handling.
A. CHARGING THE BATTERY
Refer to the battery charger’s manual for specific instructions.
Under normal conditions the engine’s alternator will have no problem keeping a charge on the battery. If the battery has been completely discharged for a long period of time, the alternator may not be able to recharge the battery, and a battery charger will be required.
DO NOT charge a frozen battery. It may explode and cause injury. Let the battery warm before attaching a charger.
Whenever possible, remove the battery from the mower before charging and make sure the electrolyte covers the plates in all cells.
WARNING
BATTERIES PRODUCE ExPLOSIvE GASES. Charge the battery in a well ventilated space so gases produced while charging can dissipate.
WARNING
Electric storage battery fluid contains sulfuric acid which is POISON and can cause SEvERE CHEMICAL BURNS. Avoid contact of fluid with eyes, skin, or clothing. Use proper protective gear when handling batteries. DO NOT tip any battery beyond 45° angle in any direction. If fluid contact does occur, follow first aid suggestions below.
BATTERY ELECTROLYTE FIRST AID
External Contact — Flush with water.
Eyes — Flush with water for at least 15 minutes and get medical attention immediately.
Internal — Drink large quantities of water. Follow with Milk Of Magnesia, beaten egg, or vegetable oil. Get medical attention immediately. In case of internal contact, DO NOT give fluids that would induce vomiting.
Charging rates between 3 and 50 amperes are satisfactory if excessive gassing or spewing of electrolyte does not occur or the battery does not feel excessively hot (over 125°F). If spewing or gassing occurs or the temperature exceeds 125°F, the charging rate must be reduced or temporarily stopped to permit cooling.
B. JUMP STARTING
The booster battery must be a 12 volt type. If a 1. vehicle is used for jump starting, it must have a negative ground system.
When connecting the jumper cables, connect the
2. positive cable to the positive battery post, then connect the negative cable to the negative battery post.
36
Page 41
R
Section 7
SGB033
Angle Blade Back
Do Not Cut In
X Must NOT Exceed
1/3 Blade Width
x
30

DRIvE BELTS7.8

All drive belts are spring-loaded and self-tensioning, however after the first 2, 4, 8 and 10 hours of operation, the belts should be checked for proper alignment and wear. Thereafter, check the belts after every 40 hours of operation or weekly, whichever occurs first.
- NOTe -
If you experience frequent belt wear or breakage, see your authorized Scag service center for belt adjustment.

CUTTER BLADES7.9

A. BLADE INSPECTION
Remove the ignition key before servicing the blades.1. Raise the mower deck to the highest position. Place 2.
the lanyard pin in the highest cutting height position to prevent the cutter deck from falling.
B. BLADE SHARPENING
- NOTe -
If possible, use a file to sharpen the blade. Using a wheel grinder may burn the blade.
- NOTe -
DO NOT sharpen the blades beyond 1/3 of the width of the blade. See Figure 7-7.
1.
Sharpen the cutting edge at the same bevel as the original. See Figure 7-7. Sharpen only the top of the cutting edge to maintain sharpness.
WARNING
Always wear proper hand and eye protection when working with cutter blades.
Check the cutter blades for straightness. If the cutter 3. blades appear bent, they will need to be replaced.
WARNING
Do not attempt to straighten a bent blade, and never weld a broken or cracked blade. Always replace it with a new blade to assure safety.
4.
If a blade cutting edge is dull or nicked, it should be sharpened. Remove the blades for sharpening. See "Blade Replacement."
- NOTe -
Keep the blades sharp. Cutting with dull blades not only yields a poor mowing job, but slows the cutting speed of the mower and causes extra wear on the engine and the blade drive by pulling hard.
Blade SharpeningFigure 7-7.
Check the balance of the blade. If the blades are out 2. of balance, vibration and premature wear can occur. See your authorized Scag dealer for blade balancing or special tools, if you choose to balance your own blades.
C. BLADE REPLACEMENT
WARNING
Always wear proper hand and eye protection when working with cutter blades.
Remove the ignition key before replacing the blades.1. Raise the mower deck to the highest position. Place 2.
the lanyard pin in the highest cutting height position to prevent the cutter deck from falling.
3.
Secure the cutter blades to prevent them from rotating, (use the optional Blade Buddy tool P/N 9212, to assist in securing the cutter blades), remove the nut from the blade attaching bolt. Remove the cutter blade, bolt and spacer from the spindle shaft. See Figure 7-8.
37
Page 42
R
Section 7
WASHER
HEX HEAD BOLT
CUTTER
BLADE
SPINDLE ASSEMBLY
CUTTER BLADE
SPACER
HEX HEAD
BOLT / NUT
CUTTER
DECK
SPINDLE SHAFT
HEX NUT-TORQUE TO 75 LB-FT
390S0161
CUTTER DECK
GEARBOX
CHECK PLUG
- NOTe -
The front of the machine will have to be raised slightly to remove the blade bolt from the cutter spindle.
4.
To install the new cutter blade, put the flat washer onto the blade bolt and slide the bolt into the hole in the cutter blade.

TIRES7.10

Check the tire pressures after every 8 hours of operation or daily.
Caster Wheels Flat Free Drive Wheels 12 PSI

CUTTER DECk GEARBOx7.11

A. CHECkING LUBRICANT LEvEL
CAUTION
The cutter deck gearbox can reach high operating temperatures. Allow the cutter deck gearbox to cool before servicing.
The fluid level in the cutter deck gearbox should be checked after every 100 hours of operation or bi-weekly, whichever occurs first.
Be sure that the blade is installed with the lift wing toward the top.
Install the spacer onto the blade bolt and insert the 5. bolt into the cutter spindle shaft.
Install the hex nut to the blade bolt at the top of the 6. cutter spindle. Secure the blades from rotating and torque to 75 lb-ft. See Figure 7-8.
Blade ReplacementFigure 7-8.
- NOTe -
1.
Lower the cutter deck to its lowest position to gain access to the cutter deck gearbox.
Clean and remove the check plug from the side of
2. the gearbox. See Figure 7-9.
Cutter Deck GearboxFigure 7-9.
Visually check that the lubricant level is up to the 3. bottom edge of the check plug hole. If lubricant is low, add SAE 80W90 lubricant through the check plug hole in the gearbox until it is level with the bottom of the check plug hole. Install the check plug and tighten securely.
38
Page 43
R
Section 7
Fill to Bottom of Filler Neck
030467-13
B. CHANGING LUBRICANT
The lubricant in the cutter deck gearbox should be changed after every 500 hours of operation or yearly, whichever occurs first.
Place a suitable container beneath the cutter deck
1. gearbox and locate the gearbox drain plug.
2.
Remove the drain plug, drain the lubricant into the container and properly discard it.
Re-install the drain plug and add SAE 80W90 3. lubricant through the check plug hole in the gearbox until it is level with the bottom of the check plug hole. Install the check plug and tighten securely.

COOLING SYSTEM7.12

WARNING
To avoid burns, always allow the engine to cool before removing the radiator cap.
Coolant LevelFigure 7-10.
Replace the radiator cap. Push down on the cap and 3. turn clockwise until it stops.
- NOTe -
The cooling system should be flushed and the coolant replaced every 500 hours of operation or annually. See your Scag dealer for proper coolant replacement.
B. CLEANING THE RADIATOR DEBRIS SCREEN
A. CHECkING COOLANT LEvEL
The coolant level should be checked before each day of operation.
Remove the radiator cap by turning it slowly 1. counterclockwise to the first stop and allow any pressure to be released. Push down on the cap and turn counterclockwise to remove.
Visually check the coolant level. The coolant level 2. should be up to the bottom of the filler neck as shown in Figure 7-10. Add a mixture of coolant and soft water as needed.
- NOTe -
Refer to the coolant manufacturer's instructions for the proper coolant mixture ratio.
After each day of operation, remove and clean the radiator debris screen.
CAUTION
To avoid personal injury, always wear safety glasses when using compressed air.
Pull the debris screen up to remove.1. Clean the debris screen with compressed air or a 2.
water hose.
- NOTe -
Check the radiator for excessive debris and clean with compressed air. Never spray a hot engine with water, use only compressed air to remove debris.
Re-install the debris screen to the radiator.3.
39
Page 44
R
C. CHECkING THE FAN BELT TENSION
Periodically check the fan belt tension. The belt should deflect 1/2" with 10 pounds of pressure. See your Scag dealer if the belt is in need of adjustment or replacement.

BODY, DECk, AND UPHOLSTERY7.13

CAUTION
Do not wash any portion of the equipment while it is hot. Do not wash the engine; use compressed air.
After each use, wash the mower and cutter deck. 1. Use cold water and automotive cleaners. Do not use pressure cleaners.
Section 7
Do not spray electrical components.2. Use a mild soap solution or a vinyl/rubber cleaner to 3.
clean the seat. Repair damaged metal surfaces using Scag touch-4.
up paint available from your authorized Scag dealer. Wax the mower for maximum paint protection.
40
Page 45
R
Section 8

ILLUSTRATED PARTS LIST

SCAG APPROvED ATTACHMENTS AND ACCESSORIES8.1

Attachments and accessor ies manufactured by companies other than Scag Power Equipment are not approved for use on this machine.
Scag approved attachments and accessories:
GC-STT-61V (p/n 9060)• GC-STT-CS61V(p/n 9064)• Mulch Plate (p/n 9288)• Hurricane Mulch (p/n 9285)• STT Hitch (p/n 9242)• STT Bumper (p/n 9256)• STT Lights (p/n 9279)• Tiger Striper (p/n 9269)• Blade Buddy (p/n 9212)•
41
Page 46
R

61v CUTTER DECk

44 61 63
69
12
65
64
52
58
54
17
59
24
14
56
28
56 33
3
A
A
B
B
4
14 29 20
53
2852
24
58
24
52
73
66
32
13
68
55
55
29
58
2
3
23
3
11
50
13
46
60
49
67
24
35
48
9
16
19
15
27
26
12
82
51 23
23
36
37
44
39
43
42
38
45
41
34
62
22
40
37
18
10
1
5
7
68
STT-EFI 2008 CD
14
29
12
30
28 31
25
31
21
22A
47
51
12
23
71
22A
13
72
74
28
29
13
26
57
75
76
77
78
79
80
81
83
84
85
70
Section 8
42
Page 47
R
Section 8
61v CUTTER DECk
Ref. No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45
Part No. Description
461863 04003-40 04019-04 481625-01 481632 04003-26 422478 04017-27 04043-06 04021-05 461846 04001-12 04021-22 04020-09 451240 04001-41 04003-12 04001-108 04063-08 04063-01 04043-04 04001-176 04019-03 04001-172 48100-15 04030-03 04040-15 04041-07 04021-09 04001-62 04001-54 04001-20 04001-136 461663 43589 481024 481022 43644 43312 43296 481025 43297 481035 48114-04 48677
Cutter Deck Velocity Plus Bolt, Carriage 7/16-14 x 1-1/4” Nut, Hex Serr. Flng. 3/8-16 Wing nut, 3/8-16 Anti-Scalp Wheel Bolt, Carriage 3/8-16 x 4” Anti-Scalp Wheel Bracket Bolt, Hex Serr. Flng. 3/8-16 x 1” Flatwasher, 5/8” Hardened Locknut, 3/8-16 Center Lock Discharge Chute Bolt, Hex Hd. 5/16-18 x 1-1/2” - Rear Nut, Hex Elastic Stop 5/16-18 Grd. 8 Nut, 5/8-11 UNC Pusharm Shaft Bolt, Hex Hd. 5/8-11 x 9-1/2” Bolt, Carriage 5/16-18 x 3/4” Bolt, Hex Hd. 5/16-18 x 4-1/2” Key, 1/4 x 1/4 x 2” Key, 1/4 x 1/4 x 1-1/4” Flatwasher,3/8 (.39 x .938 x .105”) HD Bolt, Hex Hd. 5/16-18 x 1-3/4” Nut, Hex Serr. Flng. 5/16-18 Bolt, Hex Hd. 1/4-20 x 1” Grd. 8 Bushing, .376” I.D. Oilite Lockwasher, 5/16” Flatwasher, 5/16” (.375 x .875 x .083”) Flatwasher, 3/8” (.391 x .938 x .105”) Nut, Hex Elastic Stop 3/8-16 Bolt, Hex Hd. 3/8-16 x 3-1/4” Bolt, Hex Hd. 3/8-16 x 3” Bolt, Hex Hd. 3/8-16 x 1-1/2” Bolt, Hex Hd. 3/8-16 x 1-1/2” Grd. 8 Spindle Assembly Spindle Shaft Seal, Top Bearing Assembly Spindle Housing Spacer, Outside Spacer, Inside Seal, Bottom Spindle Bushing, Bottom Nut, Special 1-1/16-18 Grease Fitting Relief Fitting, Tapered Spindle
Ref. No.
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85
Part No. Description
483378 482295 482879 482486 481558 45944 48926 48141 461842 48224 483215 461929 482745 424798 424325 461516 43590 04020-16 48763 04001-79 483704 482746 04110-03 04021-13 04001-154 424209 43681 424841 04003-23 04040-11 04021-11 483167 04003-12 04040-04 04021-04 483176 48038 04021-10 43763 424799
Spring, Discharge Chute Wheel, Anti-Scalp Cutter Blade, 21” Gearbox Assembly, Deck Drive Belt, Cutter Deck Drive Roller Shaft Tapered Hub, 1-1/8” Bore Tapered Hub, 1” Bore Idler Arm, Cutter Deck Bearings, Ball Pulley, Idler Lever Assembly, Deck Level (Incl. 77) Pulley, 6.35” O.D. (61”) Mounting Plate, RH Gearbox Belt, Cover Pusharm (Incl. 44, 63 & 64) Spacer, Spindle Bottom Nut, Hex Hd. 5/8-18 UNF Rod End, 5/8” Male RH Thread Bolt, Hex Hd. 5/8-11 x 4-1/2” Spring, Cutter Deck Pulley, 6.75 O.D. U-Nut, 3/8-16 Nut, Hex Elastic Stop 5/8-11 Bolt, Hex Hd. 5/16-18 x 4-3/4” Discharge Baffle 61V Pivot, Idler - Short Baffle, Custom Cut 61V Bolt, Carriage 3/8-16 x 1” Flatwasher, 7/16 (.500 x 1.25 x .083”) Nut, Elastic Stop 7/16-14 Bolt, Deck Adjust Bolt, Carriage 5/16-18 x 3/4” Flatwasher, 5/16” Nut, Center Lock 5/16-18 Wear Pad Wheel, Anti-Scalp Nut, Elastic Stop 5/16-18 Spacer, Gearbox Mount Mounting Plate, LH Gearbox
43
Page 48
R

CUTTER DECk CONTROLS

STT2006CDC
21
19
37
42
4
6
14
10 42
5
2
3
35
23
41
3832
34
30
7
27
33
40
41
28
28
24
26
41
40
CUTTER DECK
13
40
39
31
41
40
39
43
9
8
45
20
18
36
16
44
17
41
40
26
11
29
22
40
41
15
22
41
1
40
24
12
26
29
41
25
Section 8
44
Page 49
R
Section 8
CUTTER DECk CONTROLS
Ref. No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45
Part No. Description
461929 481764 481765 481766 04020-27 04020-28 04021-09 482429 43391 43487 43526 43527 45904 45905 04021-05 422381 423509 422346 46975 48100-14 481428 481598 424504 04020-09 04019 -03 04040-09 04041-14 48114-04 04061-07 04030-07 04004-44 04067-09 04050-08 04021-07 04105-01 423463 04014-03 481547 48540 04001-20 04019-04 04050-10 04001-74 04003-04 04009-02
Lever Assembly, Deck Level Link, Deck Lift Rod End, Female - 1/2-20 RH Rod End, Female - 1/2-20 LH Nut, Jam 1/2-20 RH Nut, Jam 1/2-20 LH Nut, 3/8-16 Elastic Stop Slide Weldment, Height Adjustment Spacer, Decklift Pedal Pin, Decklift Swivel Joint, LH Swivel Joint, RH Bellcrank Weldment, LH Rear Bellcrank Weldment, RH Rear Locknut, 3/8-16 Center Lock Guide, Short Guide, Long Lockplate, Decklift Deck Latch (Incl. 20 & 21) Bushing, .502” I.D. Grip, Deck Latch Spring, Helper (61” & 72” Cutter Decks Only) Foot Pedal, Height Adjustment Nut, Hex 5/8-11 Nut, Hex Serr. Flng. 5/16-18 Flatwasher, 5/8” (.656 x 1.312 x .095”) Flatwasher, 1” (1.062 x 1.50 x .048”) Grease Fitting Cotter Pin, 3/16 x 1” Lockwasher, 5/8” Stud, 5/8-11 x 22.0” Ring Pin, 1/2 x 3.06” Ring, Retaining 1” External “E” Nut, Hex Elastic Stop 1/2-13 Capscrew, 5/8-11 x 1-1/2” Bracket, Cutting Height Adjustment Screw, Cap 5/16-18 x 3” FHHS Lanyard, Deck Height Pin Chain Bolt, Hex Hd. 3/8-16 x 1-1/2” Nut, Hex Serr. Flng. 3/8-16 Ring, Retaining 1/2” External “E” Bolt, Hex Hd. 1/2-13 x 3” Bolt, Carriage 5/16-18 x 1” Bolt, Shoulder 1/2 x 3/4”
45
Page 50
R

SHEET METAL COMPONENTS

STT 2008 SMC
46
47
48
15
50
26
30
25
12
15
19
9
1
23
24
31 32
33
34
29
33
36 37
40
39
38 41
42
43
55
35
44
45
15
27
22
54
20
28
15
14
13
12
11
10
16
17
A
20
5
3
4
8
7
18
18
56
57
58
54
Suspension Seat
59
60
49
51
52
53
A
A
6
Section 8
46
Page 51
R
Section 8
SHEET METAL COMPONENTS
Ref. No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29
30 31 32 33 34 35
36 37 38 39 40 41 42 43 44 45
Part No. Description
451481 04001-09 43606 04041-07 461967 424819 04001-45 04021-09 * 48903 421274 04003-12 423308 04029-01 04019-03 04003-01 48661 43584 04003-04 482622 04021-09 461991 04019-04 04017-27 451480 423489 04021-09 04001-19 04001-125 04001-186 04021-13 481559 04021-20 481657 482028-01 451825 451451 481025 04021-07 451416 04001-167 43583 9278 04001-01 04001-01 423674 482943 482948
Fender Weldment, RH Bolt, Hex Hd., 5/16-18 x 1, Zinc Spacer Flatwasher, 3/8 (.391 x .938 x .105”) Seat Plate Weldment Guard, Fuel Line Bolt, Hex Hd. 3/8-16 x 2.0” Nut, Elastic Stop 3/8-16 Battery (not avail. through Scag) Pad, Battery Cover Cover, Battery Bolt, Carriage 5/16-18 x 3/4” Plate, Battery Box Wing Nut, 1/4-20 x 3/4” Nut, Hex Serr. Flng. 5/16-18 Bolt, Carriage 1/4-20 x 6” Rubber Pad Spacer, Caster Wheel Bolt, Carriage 5/16-18 x 1” Seal Locknut, 3/8-16, Elast. Stop Main Frame Nut, Hex Serr. Flng. 3/8-16 Screw, Hex Serr. Flng. 3/8-16 x 1” Fender Weldment, LH Foot Plate Nut, Hex Elastic Stop 3/8-16 Bolt, Hex Hd. 3/8-16 x 1” Bolt, Hex Hd. 5/8-11 x 4” Bolt, Hex Hd. 5/8-11 x 4-1/4” Nut, Hex Elastic Stop 5/8-11 Cap, Grease Nut, Hex Elastic Stop 1.0-14 Bearing w/Race Plug, 1/4-28 THD Form Extension Weldment, Caster 61V LH Extension Weldment, Caster 61V RH Seal, 2.00” O.D. x 1.625” Bore Nut, Hex Elastic Stop 1/2-13 Yoke Weldment, Caster (61V) Bolt, Hex Hd. 1/2-13 x 9-1/2” (61V) Sleeve, Caster Wheel (61V) Wheel Assy, 61V, 72A (Incl. 20, 54, & 55) Bolt, Hex Hd. 1/4-20 x 3/4” Bolt, Hex Hd. 1/4-20 x 3/4” Mounting Bracket, STT Cup Holder Lumbar Kit Knob Kit
Ref. No.
46 47 48 49
50
51 52
53 54 55 56 57 58 59 60
Part No. Description
48566 482940 9240 482941
461908 461909 482944
482948 482952 482942 482621 48114-10 481389 43462 04060-01 483428 482950 482945 482946
Cable, Seat Stop Back Cushion Kit Cup Holder Assembly Seat Cushion Kit Seat Drain Kit (Incl. with Seat Cushion) Caster Wheel Assembly (Incl. 31 thru 43) 61V LH Caster Wheel Assembly (Incl. 31 thru 43) 61V RH Weight Adjustment Kit Knob Kit Seat Adjustment, Track Set Shock Absorber Kit Bearing w/Race Grease Fitting Spring, Seat Pin Retainer, Spring Roll Pin, Spring 5/32 x 3/4” Suspension Seat Assembly w/Seat Belt Armrest Only Armrest Assembly Kit, LH Armrest Assembly Kit, RH
47
Page 52
R
Section 8
STT 2007 FOLD ROPS
1
2
2
3
3
4
4
5
5
6
6
7
8
9
10
11
12
13
14
14
15
15
21
20
17
18
16
19
1
1
22

STT ROLL-OvER PROTECTION SYSTEM - WITH SUSPENSION SEAT

48
Page 53
R
Section 8
STT ROLL-OvER PROTECTION SYSTEM - WITH SUSPENSION SEAT
Ref. No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
Part No. Description
9514 04001-82 04021-19 04001-178 04040-11 483594 04001-45 04041-07 43606 04021-09 04001-09 461968 424193 04019-03 04040-13 04001-145 04021-19 424407 483262 481625-03 04062-06 483265
STT, ROPS Accessory (Incl. all items below) Bolt, Hex Hd. 1/2-13 x 4-1/2” Nut, Center Lock 1/2-13 Bolt, Hex Hd. 7/16-20 x 1” Flatwasher, 7/16 (.500 x 1.25 x .083”) Retractable Seat Belt Bolt, Hex Hd. 3/8-16 x 2” Flatwasher, 3/8 (.391 x .938 x .105”) Sleeve, Seat Base Mounting Nut, Elastic Stop 3/8-16 Bolt, Hex Hd. 5/16-18 x 1” Bracket, Seat Hold Down w/Decal Spacer, Seat Hold Down Nut, Serr. Flng. 5/16-18 Flatwasher, 1/2 (.562 x 1.375 x .109”) Bolt, Hex Hd. 1/2-13 x 3-1/2” Nut, Center Lock 1/2-13 Bracket, Stop Pin Thumb Screw, 5/16-18 NC x 3/4” Hair Pin, Cotter Clamp
49
Page 54
R

DECk DRIvE COMPONENTS

STT 2005 DDC
B
A
A
B
C
C
Frame
2
1
40
3
47
46
47
43
42
4
41
45
59
53
8
54
72
5
6
64
63
62
7
52
55
9
60
61
10
11
56
52
12
15
65
58
52
14
13
12
20
17
45
18
66
19
67
45
56
21
57
58
52
22
18
23
24
49
50
69
25
26
27
28
29
30
36
35
34
33 32
31
68
48
51
38
71
73
70
39
53
45
46
52
44
45
45
45
37
73
16
45
52
74
75
76
Section 8
50
Page 55
R
Section 8
DECk DRIvE COMPONENTS
Ref. No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44
45
Part No. Description
423925 481531 481309 482845 48030-09 461661 482876 483088 48181 481536 482949 481884 483678 483214 483675 43631 04063-14 48224 481284 482744 482667 461609 43632 461697 481035 43297 481025 481022 43312 43296 48114-04 48677 43644 481022 481024 43534 461608 482438 04012-08 04011-11 04041-07 04069-01 43507 461801
04019-04
Belt Guard, Rear Hinge, Belt Guard Latch, Hood Rod Assembly, Clutch Anti-Rotation Clamp, Cable Clutch, Ogura GT-3.5 Belt, Deck Drive Spring, Transmission Idler Pulley, Idler 5” Dia. Tapered Hub, 1” Bore Pulley, 6.70” Tapered Bore Tapered Hub, 17mm Bore Belt, Pump Drive Pulley, Idler 4” Dia. Pulley, 5.367” Dia. - 1.125” Bore Spacer, Idler Bearing Key, 5.0 x 5.0 x 25mm Ball Bearing Bumper, Rubber Pulley, 5.75” O.D. Spring, PTO Idler Arm Weldment, PTO Drive Pivot, Idler PTO Spindle Assembly, Deck Drive Nut, 1.06-18 Thread Spindle Bushing, Bottom Seal, 2.0” O.D. x 1.625” Bore Roller Bearing Tapered Spacer, Outside Spacer, Inside Grease Fitting, 1/4-28 Relief Fitting Spindle Housing Roller Bearing Tapered Seal, 2.0” O.D. x 1.5” Bore Shaft, Deck Drive Idler Arm Weldment, Pump Drive Driveshaft (Liquid-Cooled Engine) Set Screw, 3/8-16 x 3/4” Torx Socket Screw, #10-32 x .56 Flatwasher, 3/8 (.391 x .938 x .105”) Pin, Rue Cotter 3/8” Dia. Stud, Anti Rotation Pump Mounting Plate Weld. (Liquid-
Cooled)
Nut, Serr. Flng. 3/8-16
Ref. No.
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76
Part No. Description
04019-02 04003-07 04021-22 04001-176 04063-06 04001-171 04043-04 04001-135 04001-136 04001-170 04021-05 04001-136 04021-09 04001-45 04001-109 04030-02 04001-101 04030-05 04041-28 04001-172 04001-21 04019-03 04021-09 04001-19 04021-05 04001-21 04063-02 04063-20 424138 43063 04001-19
Nut, Serr. Flng. 1/4-20 Bolt, Carriage 1/4-20 x 1/2” Nut, Elastic Stop 5/16-18 Grd. 8 Bolt, Hex Hd. 5/16-18 x 1-3/4” Grd. 8 Key, 1/4 x 1/4 x 1-1/2” Bolt, Hex Hd. 3/8-16 x 4-1/2” Grd. 8 Black Washer, 3/8” Hardened Bolt, Hex Hd. 3/8-16 x 1-3/4” Grd. 8 Black Bolt, Hex Hd. 3/8-16 x 1-1/2” Grd. 8 Black Bolt, Hex Hd. 3/8-16 x 2-1/2” Grd.8 Nut, Center Lock 3/8-16 Bolt, Hex Hd. 3/8-16 x 1-1/2” Grd. 8 Black Nut, Elastic Stop 3/8-16 Bolt, Hex Hd. 3/8-16 x 2” Bolt, Hex Hd. 1/4-20 x 1-3/8” Lockwasher, 1/4” Spring Bolt, Hex Hd. 7/16-20 x 2-1/2” UNF Lockwasher, 7/16” Spring Flatwasher, 7/16 (.469 x 1.75 x .25”) Bolt, Hex Hd. 1/4-20 x 1” Grd. 8 Bolt, Hex Hd. 3/8-16 x 1-3/4” Nut, Serr. Flng. 5/16-18 Nut, Elastic Stop 3/8-16 Bolt, Hex Hd. 3/8-16 x 1” Nut, Center Lock 3/8-16 Bolt, Hex Hd. 3/8-16 x 1-3/4” Key, 1/4 x 1/4 x 2-1/4” Key, 1/4 x 1/4 x 1” Bracket Spacer Bolt, Hex Hd. 3/8-16 x 1”
51
Page 56
R
Section 8
STT 2008 EAPKH-EFI
8
9
6
10
13
FRAME
REF. PUMP
MTG. WELDMENT
11
1
3
5
2
10
12
10
12
10
12
13
14
17
15
16
7
4
18
19
20
21
22
23
24

ENGINE & ATTACHING PARTS - 31HP-EFI kOHLER

52
Page 57
R
Section 8
ENGINE & ATTACHING PARTS - 31HP-EFI kOHLER
Ref. No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Part No. Description
424910 04017-05 ** 451997 04110-01 483355 482510 483687 04001-19 04030-04 04001-21 04021-09 04001-32 451454 04003-12 04019-03 424691 ** 04002-23 424888 43774 424889 04017-05 04019-02
Muffler Guard (Kohler) Screw, Hex Serr. Flng. 1/4-20 x 3/4” Muffler (Available only through Kohler) Screen Weldment, Radiator (Kohler) U-Nut, 1/4-20 Hour Meter Oil Drain Extension ** Engine, Kohler 31HP-EFI Aegis (Available only through Kohler) Bolt, Hex Hd. 3/8-16 x 1” Lockwasher, 3/8” Spring Bolt, Hex Hd. 3/8-16 x 1-3/4” Nut, Hex Elastic Stop 3/8-16 Bolt, Hex Hd. 3/8-16 x 1-1/4” Plate, Engine Mounting Bolt, Carriage 5/16-18 x 3/4” Nut, Hex Serr. Flng. 5/16-18 Rear Cover o2 Sensor (Available through Kohler Only) Bolt, Hex Hd. M6-1.0 X 90mm Mounting Bracket, ECU Kohler EFI Spacer, ECU Mounting Mounting Bracket, Fuel Pump Kohler EFI Bolt, Hex Hd. 1/4-20 x 3/4” Nut, Serr. Flng. 1/4-20
** Available through the individual engine manufacturer.
53
Page 58
R

BRAkE AND STEERING COMPONENTS

STT DB&SC
A
1
10
11
33
17
9
19
23
41
11 21
34
36
57
73
48
47
46
42
43 44 45
15
56
70
69
71
62
65
64
67
60
52
51
50
34
35
TO RH PUMP
TO LH PUMP
37
36
27
28
35
33
78
34
31
30
29
8
9
32
13
B
9
B
25
18
72
49
55
54
75
26
5
68
66
37
36
61
59
74
7
20
13
14
22
14
39
16
24
38
63
24
38
12
79
22
21
A
40
38
80
77
45
2
76
4
3
6
6
81
5
82
5
53
34
58
5
C
C
59
11
83
Section 8
54
Page 59
R
Section 8
BRAkE AND STEERING COMPONENTS
Ref. No.
1 2
3 4 5 6 7
8 9 10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45
Part No. Description
482340 461914 461923 04001-09 04030-03 483250 483238 451483 451484 04001-17 04021-10 04001-45 04021-09 423488 48224 43607 04069-01 04001-13 04021-13 461601 461602 04003-04 43600 04003-12 04019-03 04050-01 43602 45918 04003-02 04040-14 04021-08 43477 481389 04060-01 04061-06 482586 04020-25 43624 04020-26 482585 04021-10 482794 482330 48114-04 461082 481548 04001-22 43773
Grip, Handle Bar Handle Bar, LH (Incl. item 1) Handle Bar, RH (Incl. item 1) Bolt, Hex Hd. 5/16-18 x 1” Lockwasher, 5/16” Rubber Spacer Bar, Control Lever Control Lever Weldment, LH Control Lever Weldment, RH Bolt, Hex Hd. 5/16-18 x 2” Nut, Hex Elastic Stop 5/16-18 Bolt, Hex Hd. 3/8-16 x 2” Nut, Hex Elastic Stop Mount, Control Linkage Ball Bearings, Neutral Return Spacer Pin, Rue Cotter 3/8” Dia. Bolt, Hex Hd., 5/16-18 x 2.75 Zinc Nut, Hex Elastic Stop 5/8-11 Bracket, Control Lever LH Bracket, Control Lever RH Bolt, Carriage 5/16-18 x 1” Spacer, Bearing Bolt, Carriage 5/16-18 x 3/4” Nut, Hex Serr. Flng. 5/16-18 Ring, Retaining 5/8” External “E” Spacer Bracket, Neutral Return Bolt, Carriage 1/4-20 x 3/4” Flatwasher, 1/4” (.312 x .750 x .065”) Nut, Hex Elastic Stop 1/4-20 Pin, Retaining Spring Spring Roll Pin, Spring 5/32 x 3/4” Pin, Cotter 9/16 x 1-1/2” Rod End, Male 3/8-24 RH Thread Nut, 3/8-24 RH Thread Tube, Control Link Liquid-Cooled Engine Nut, Hex 3/8-24 LH Thread Rod End, Male 3/8-24 LH Thread Locknut, 5/16-18, Elastic Stop Gas Damper Rod End, 3/8-24 RH Female Grease Fitting Lever, Parking Brake (Incl. 43) Grip, Parking Brake Bolt, Hex Hd. 3/8-16 x 2-3/4” Swivel Joint
Ref. No.
46 47 48 49 50 51 52 53 54 55 56
57 58 59
60 61 62 63 64 65 66 67 68 69
70 71 72 73 74 75 76 77 78 79 80 81 82 83
Part No. Description
48343-04 04064-02 04062-01 04004-34 48544 482061 04001-08 04001-192 481637 04010-12 451970 451971 45953 48807 04001-190 04001-52 04021-19 04009-13 483677 04001-12 483701 424894 43063 461438 04063-25 481850 481851 481852 04028-02 48680 422373 04001-20 423279 423491 04017-16 04003-36 04001-19 481638 04001-168 04003-38 483269 04021-05
Clevis, Traction Control Pin, Clevis 3/8-16 x 1-1/16” Hair Pin Cotter Rod, Parking Brake Rod End, LH Thread Bushing, Self Align Bolt, Hex Hd. 5/16-18 x 3/4” Bolt, Hex Hd 3/8-24 x 5-1/2” Switch Screw, Hex Sltd. Wshr. Hd. #10 32 x 3/4” Brake Linkage, LH Brake Linkage, RH Bellcrank, Brake Actuator Spring Bolt, Hex Hd. 1/2-13 x 2-3/4” (upper) Bolt, Hex Hd. 1/2-13 x 2-1/2” (lower) Locknut, Hex 1/2-13 Center Lock Bolt, Shoulder 3/8-16 x 2-1/2” Wheel Motor, Hydro-Gear 18E Bolt, Hex Hd., 5/16-18 x 1.75”, Zinc Brake Caliper Mounting Bracket, Brake Spacer Wheel Hub/Disk Brake Assembly Key, Woodruff 5/16 x 1” Wheel Assembly 24 x 12-12 Turf Master Rim w/Valve Stem Tire, 24 x 12-12 Turf Master Lug Nut, 1/2-20 Nut, Hex Castle Threaded Plate Bolt, Hex Hd. 3/8-16 x 1-1/2” Plate Weldment, Motor Backing Actuator Switch Bolt, Hex Serr. Flng. 5/16-18 x 3/4” Bolt, Carriage 3/8-16 x 4-3/4” Bolt, Hex Hd. 3/8-16 x 1” Switch Bolt, Hex Hd. 3/8-16 x 1-1/4” Grd. 8 Bolt, Carriage 5/16-18 x 1-1/2” Knob Nut, Center Lock 3/8-16
55
Page 60
R

FUEL AND HYDRAULIC SYSTEM - kOHLER 31EFI

D
D
D
E
F
C
I
H
G
G
F
E
A
A
B
C
DUMP VALVE
B
2008 STT F&HS-EFI.eps
I
H
39
23 24 26 40
32
36 37
Z
34 25 35
21 31
33
9
30
30
57 56 54
7
4
4
3
44 45 50
46
51
53
52
49
5
4
4
5
42
34 25 35
55
18
8 20 19
6
22 41
27 28
29 30
38
Z
2
2
60 58 59
7
7
22
5
4
4
43 (2)
43 (2)
7
5
1
To Back Side of Reservoir (Not Shown)
10
62
63
11
15
To Engine
16
17
Fuel
Return
64
15
14
14
13
14
10
48
47 14
12
12
65
65
65
65
66
66
Section 8
56
Page 61
R
Section 8
FUEL AND HYDRAULIC SYSTEM - kOHLER 31EFI
Ref. No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
28 29 30 31 32 33 34 35 36 37 38 39
40 41 42 43 44 45
Part No. Description
04110-01 48136-13 04001-03 48811 48136-07 481301-03 482266-01 48471-02 482606 48059-01 ** *483691 481308 48059-01 483620 483749 48309 04001-09 04019-03 48758 482483 04021-08 481164 481507 48603-02 461451 482572 482571 48136-13 48811 04010-10 48571-02 461586 48136-05 48350-02 48938-02 423701 04019-03 04003-02 482574 482573 423513 423485 481611 48572-04 04001-59 04030-02
U-Nut 1/4-20 Hose Clamp, 0.69” Dia. Bolt, Hex Hd. 1/4-20 x 2.0” *** Hose, 3/8” I.D. Pushlock Clamp, Hose 1/2” Elbow, 90 Degree - 1/4” NPT x 3/8” Hose Elbow, 90 Degree - 9/16” O-ring x 3/8” Hose Oil Filter Base Hose Assy., 1/2” I.D. (Tank to Filter Base) Clamp, Fuel Hose 1/4” Hose I.D. Fuel Filter, Kohler (p/n 24 050 03) *** Fuel Hose, 5/16” I.D. Non-Perm. Valve, Shutoff Clamp, Fuel Hose *** Fuel Hose, 5/16” I.D. Non-Perm. Hose Fitting w/Screen Bushing Bolt, Hex Hd. 5/16-18 x 1.0” Zinc Nut, Serr. Flng. 5/16-18 Oil Filter Tee, 3/4 O-ring x JIC x 1/2” Hose Nut, Hex Elastic Stop 1/4-20 Cap, Hydraulic Tank Insert, Filler Neck O-Ring Oil Reservoir Assembly (Incl. 24, 27, & 39) Elbow, 90 Degree .38” Hose Bushing, .56” Dia. Viton Hose Clamp, 0.69” Dia. *** Hose, 3/8” I.D., Pushlock Screw, Phillips Head, 1/4-20 Cap Fuel Tank Assembly (Incl. 16, 17, 65, & 66) Clamp, Hose Elbow, 90 Degree, 7/8-14 THD Bushing, 7/8-14 JIC x 3/4-16 O-Ring Support Bracket, Fuel Tank Nut, 5/16-18 Serr. Flng. Bolt, Carriage 1/4-20 x 3/4” Elbow, 90 Degree Bushing, .78” Dia. Viton Strap, Hydraulic Tank Support Bracket, Hydraulic Tank Hose Assembly, Pump Union, 3/4-16 JIC x 3/4-16 O-ring Bolt, Hex Hd., 1/4-20 x 1-14” Lockwasher, 1/4” Spring
Ref. No.
46 47 48 49 50 51 52 53 54 55 56 57 58
59 60 61 62 63 64
65 66
Part No. Description
04060-09 ** 48309 422694 481793 483101 04021-09 04001-32 483100 482497 04021-09 04043-04 423524 423525 04001-08 482505 48136-13 482703 483622 **
483699 482839-01
Roll Pin, Spring 3/16 x 3/4” Fuel Pump, Kohler 31EFI (p/n 24 393 20) Bushing Clamp Plate, Pump Control Block, Pump Control Pump, Left Hand, BDP-16A Nut, Hex, Elastic Stop 3/8-16 Bolt, Hex Hd., 3/8-16 x 1-1/4 Pump, Right Hand, BDP 16A Cap, Fuel Tank w/Gauge Nut, Hex Elastic Stop 3/8-16 Flatwasher, 3/8” (.391 x .938 x .105”) Grd. 8 Mounting Bracket - LH, Oil Cooler Mounting Bracket - RH, Oil Cooler Bolt, Hex Hd. 5/16-18 x 3/4” Cooler, Oil Clamp, .69” Dia. Fitting, Hose *** Hose, 1/4” Fuel Line Non-Perm. Regulator Assembly, Fuel Pressure (p/n 24 403 16) Fuel Clamp, 5/16” Oetiker Shield, Flexible
* High Pressure Fuel Line. MUST only be replaced with the part number listed. ** Available through the individual engine manufacturer. *** Order by Inch.
57
Page 62
R

BDP-16A HYDRAULIC PUMP ASSEMBLY WITH COOLING FAN

OR
OR
PORT "A" SIDE
PORT "B" SIDE
Overhaul Seal Kit
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
17
18
19
20
20
21
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
27
Section 8
58
Page 63
R
Section 8
BDP-16A HYDRAULIC PUMP ASSEMBLY WITH COOLING FAN
Ref. No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
Part No. Description
HG70740 HG51455 HG70735 HG51462 HG51436 HG2000015 HG2000014 HG2000025 HG2000024 HG2000032 HG2000023 HG2000038 HG51092 HG70578 HG70738 HG70739 HG50641 HG51437 HG9005110-7500 HG70743 HG70742 HG9005200-7500 HG70736 HG2513030 HG9004100-1430 HG50406 HG50173 HG70924 HG51457 HG70402 HG71287 HG51348 HG52016 HG52014 HG51348 HG44809 HG52059
Overhaul Seal Kit Valve Plate Cylinder Block Kit - 16cc Thrust Ball Bearing Assembly Variable Swashplate Slot Guide Trunnion Arm Block Spring Block Thrust Washer Shaft Ball Bearing Spacer Retaining Ring Seal Kit, Pump Shaft (keyed thru taper) Housing Kit Trunnion Seal Kit Pin O-Ring Straight Thread Plug Shock Valve Kit (.031” Orifice) Shock Valve Kit (.024” Orifice) Straight Thread Plug End Cap Kit Bypass Valve Kit O-Ring Gerotor Assembly (.19 cu.in./rev.) Socket Head Cap Screw (M8 x 1.25-25mm) Charge Pump Kit (.19 STD. Splined) Hex Screw, Flng. Head (M10 x 1.50-65mm) Charge Relief Kit Fan Kit (Incl. 32, 33, 34, 35, 36, & 37) Hub Bracket, Shroud Fan Washer Nut Shroud
59
Page 64
R

ELECTRICAL SYSTEM (31HP-EFI kOHLER)

SCAG
POW
ER EQU
IPMENT
21
28
1
3
4
5
6
13
17
STT2008 ESKH-EFI
10
11
17
18
15
14
20
22
23
24
25
26
28
29
30
14
15
9 10
11
8
B
B
7
15 14
16
A
31
18
A
C
C
12
32
34
20
33
35
36
37
2
Section 8
60
Page 65
R
Section 8
ELECTRICAL SYSTEM (31HP-EFI kOHLER)
Ref. No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
Part No. Description
481184 48298 462069 48017-04 48017-03 461916 48798 483162 48788 04031-01 04020-01 481183 451879 04030-02 04001-01 04110-01 481662 04010-01 481638 04001-44 48029-06 04020-02 48029-11 48030-09 48136-05 48030-11 481670 483688 04031-03 04002-12 483029 481945-01 483641 481182 483629 483643 482588
Volt Meter Fuse, 20 AMP Key, Assembly w/Fob Nut, Hex 5/8-32 Lockwasher, 5/8” Internal Instrument Panel, Top w/Decals Key Switch Switch, PTO Relay Lockwasher, #10 External Tooth Nut, Hex #10-32 Water Temp. Gauge Base, Instrument Panel Lockwasher, 1/4” Bolt, Hex Hd. 1/4-20 x 3/4” U-Nut, 1/4-20 Throttle Controls Screw, Phillips Washer Head #10-32 x 1/2” Switch, Interlock-Seat Bolt, Hex Hd. 1/4-20 x 1/2” Cable, Battery - Red Nut, Hex 1/4-20 Cable, Battery - Black Clamp, Cable 1/2” I.D. Clamp, Cable 3/4” I.D. Clamp, Cable Sending Unit, Water Temp. Wire Harness, STT Liquid-Cooled Electronic Fuel Injection (EFI) Lockwasher, 5/16” External Tooth Bolt, Hex Hd. M8-1.25 x 20mm Electronic Module Heatshield, Flexible Single Fuse Assembly, Sealed (Incl. 2, 35, 36, & 37) Indicator Light, Check Engine Fuse Holder Cover, Sealed Single Clip, Wire
61
Page 66
R

REPLACEMENT DECALS AND INFORMATION PLATES

1
2
3
5
8
6
4
9
13
14
7
48404
STT-EFI 2008 Decals 1
WARNING
INSTALL BELT COvER BEFORE
OPERATING MACHINE
READ OPERATOR'S MANUAL
481568
FORWARD
REvERSE
F
R
11
482508
PULL OUT TO ENGAGE
ON
START
PUSH IN TO DISENGAGE
OFF
MOWER DECk
Hea
vy-
Duty
Co mmerc
ial
481971
10
22
CHECk
ENGINE LIGHT
482984
SLOW
FAST
23
25
MANUFACTURED UNDER ONE OR MORE
OF THE FOLLOWING PATENTS: 4,487,006 4,885,903 4,920,733 4,967,543 4,991,382 4,998,948 5,042,239 5,117,617 5,133,176 5,826,416 5,832,708 5,865,018 6,192,666 6,766,633 6,892,519 6,996,962 7,065,946 7,197,863
PATENTS PENDING
Section 8
62
Page 67
R
Section 8
481569
R
16
2007 STT-EFI Decals Page2
17
1918
15
481663
481664
20
21
24
12
REPLACEMENT DECALS AND INFORMATION PLATES
Ref. No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 **
Part No. Description
483192 483406 483201 483397 483044 481568 481971 48404 483402 483429 482508 483633 482565 483444 482710 482577 483229 481664 481663 481694 483405 482493 482984 483158 483425 461982
Decal, Danger-Spinning Blades Decal, Warning-Rotating Blades Decal, 61 Velocity Plus Decal, Fuel Tank Decal, Patents Decal, Traction Control Decal, Heavy Duty Commercial Decal, Metalcraft-Made In USA Decal, Belt Cover Decal, Warning Seat Hold Down Decal, Instrument Panel-Upper Decal, Seat Replacement Decal, Cutting Height - Lower Decal, Start/Drive Procedure Decal, Seat Support Decal, Turf Tiger Decal, Turf Tiger Decal, Stripes-RH Decal, Stripes-LH Decal, Tiger Decal, Warning Decal, Cutting Height - Upper Decal, Instrument Panel - Lower Decal, ROPS Decal, ROPS Spanish Decal Kit, STT (not shown)
63
Page 68
R
RELAY
MODULE
PLUG
POS
NEG
PTO
SWITCH
KEY
SWITCH
CLUTCH
HOURMETER
GROUND
R.H. NEUTRAL
SWITCH
20 AMP FUSE
BRAKE
INTERLOCK
SWITCH
SEAT
SWITCH
L.H. NEUTRAL
SWITCH
WATER TEMP
WATER TEMP
SENDER
STARTER
SOLENOID
STARTER B+
FUEL PUMP
ENGINE
DIAGNOSTIC
LIGHT
POS
NEG
ENGINE
PLUG
PINK
BROWN
RED W/WHITE STRIPE
GRN W/WHT STRIPE
GRN W/BLK STRIPE
LIGHT BLUE
BLUE
BLACK
RED
RED
RED
RED
RED
RED
RED
RED
RED
RED
RED
RED
RED
RED
RED
RED
RED
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK
WHITE W/BLK STRIPE
WHITE W/BLK STRIPE
WHITE W/BLK STRIPE
ORANGE
ORANGE
BROWN
RED W/WHITE STRIPE
PINK
BLACK W/ORANGE STRIPE
BLACK W/ORANGE STRIPE
GRN W/WHT STRIPE
VOLT METER

ELECTRICAL SCHEMATIC (kOHLER 31HP - EFI)

Section 8
64
Page 69

LIMITED WARRANTY - COMMERCIAL EqUIPMENT

Any part of the Scag commercial mower manufactured by Scag Power Equipment and found, in the reasonable judgment of Scag, to be defective in materials or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor during the periods specified below. This warranty is limited to the original purchaser and is not transferable. Proof of purchase will be required by the dealer to substantiate any warranty claims. All warranty work must be performed by an Authorized Scag Service Dealer.
This warranty is limited to the following specified periods from the date of the original retail purchase for defects in materials or workmanship:
Wear items including drive belts, blades, hydraulic hoses and tires are warranted for ninety (90) days.• Batteries are covered for ninety (90) days.• Frame and structural components including oil reservoir and oil coolers are warranted for 2 years (Parts and labor).•
Cutter decks are warranted against cracking for a period of three (3) years. (Parts and labor 1st and 2nd year; Parts • only 3rd year.) The repair or replacement of the cutter deck will be at the option of Scag Power Equipment. We reserve the right to request components for evaluation. This warranty does not cover any mower that has been subject to mis­use, neglect, negligence, or accident, or that has been operated in any way contrary to the operating instructions as specified in the Operator’s Manual.
Engines and electric starters are covered by the engine manufacturer’s warranty period.•
Major drive system components are warranted for two (2) years by Scag Power Equipment. (Parts and labor) (Two • year warranty exclude fittings, hoses, drive belts). The repair or replacement of the hydraulic pump or hydraulic mo­tor will be at the option of Scag Power Equipment. This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or accident, or that has been operated in any way contrary to the operating instructions as specified in the Operator’s Manual.
Electric clutches have a Limited Warranty for 2 year (Parts and labor).•
Spindle assemblies have a Limited Warranty for three years (Parts and labor 1st year and 2nd; Parts only 3rd year).•
Any Scag product used for rental purposes is covered by a 90 day warranty.•
The Scag mower, including any defective part must be returned to an Authorized Scag Service Dealer within the warranty period. The expense of delivering the mower to the dealer for warranty work and the expense of returning it to the owner after repair will be paid for by the owner. Scag’s responsibility is limited to making the required repairs and no claim of breach of warranty shall be cause for cancellation or rescission of the contract of sale of any Scag mower.
This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or accident, or that has been operated in any way contrary to the operating instructions as specified in the Operator’s Manual.
The warranty does not apply to any damage to the mower that is the result of improper maintenance, or to any mower or parts that have not been assembled or installed as specified in the Operator’s Manual and Assembly Manual. The warranty does not cover any mower that has been altered or modified, changing performance or durability. In addition, the warranty does not extend to repairs made necessary by normal wear, or by the use of parts or accessories which, in the reasonable judgment of Scag, are either incompatible with the Scag mower or adversely affect its operation, performance or durability.
Scag Power Equipment reserves the right to change or improve the design of any mower without assuming any obligation to modify any mower previously manufactured. All other implied warranties are limited in duration to
the two (2) year warranty period or ninety (90) days for mowers used for rental purpose. Accordingly, any such implied warranties including merchantability, fitness for a particular purpose, or otherwise, are disclaimed in their entirety after the expiration of the appropriate two year or ninety day warranty period. Scag’s obligation under this warranty is strictly and exclusively limited to the repair or replacement of defective parts and Scag does not assume or authorize anyone to assume for them any other obligation. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Scag assumes no responsibility for incidental, consequential or other damages including, but not limited to, expense for gasoline, expense of delivering the mower to an Authorized Scag Service Dealer and expense of returning it to the owner, mechanic’s travel time, telephone or telegram charges, rental of a like product during the time warranty repairs are being performed, travel, loss or damage to personal property, loss of revenue, loss of use of the mower, loss of time or inconvenience. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Page 70
GARANTÍA LIMITADA - EQUIPO COMERCIAL
Toda pieza del cortacésped comercial Scag fabricada por Scag Power Equipment que, según criterio razonable de Scag, presente materiales o mano de obra defectuosos será reparada o reemplazada por un distribuidor autorizado Scag sin cargo por las piezas ni mano de obra durante los períodos especificados abajo. Esta garantía se limita al comprador original y no es transferible. Para acceder a cualquier reclamo de garantía, el distribuidor requerirá el comprobante de compra. T odo trabajo bajo garantía debe realizarlo un distribuidor autorizado Scag.
Con respecto a materiales o mano de obra defectuosos, esta garantía se limita a los siguientes períodos especificados a partir de la fecha de compra original:
* Los artículos desgastables, incluyendo correas de transmisión, cuchillas, mangueras hidráulicas y llantas, están garantizados por noventa (90) días. * Las baterías están garantizadas por noventa (90) días. * El bastidor y los componentes estructurales, incluyendo el depósito de aceite y los enfriadores de aceite, tienen una garantía de 2 años (Piezas y mano de obra). * Las plataformas de corte están garantizadas contra grietas por un período de tres (3) años. (Piezas y mano de obra, primer y segundo año; piezas solamente, tercer año). La reparación o el reemplazo de la plataforma de corte estarán sujetos a discreción de Scag Power Equipment. Nos reservamos el derecho de solicitar componentes para su evaluación. Esta garantía no cubre ningún cortacésped que haya sido sometido a uso indebido, descuido, negligencia o accidente, o que se haya operado de manera distinta a la especificada en el manual del operador. * Los motores eléctricos y los arrancadores están cubiertos por el período de garantía del fabricante de motor. * Los componentes principales del sistema de transmisión están garantizados por Scag Power Equipment por dos (2) años. (Piezas y mano de obra) (La garantía de dos años no incluye las conexiones, mangueras, las correas de transmisión). La reparación o el reemplazo de la bomba hidráulica o el motor hidráulico estarán sujetos a discreción de Scag Power Equipment. Esta garantía no cubre ningún cortacésped que haya sido sometido a uso indebido, descuido, negligencia o accidente, o que se haya operado de manera distinta a la especificada en el manual del operador. * Los embragues eléctricos tienen una Garantía limitada de 2 años (Piezas y mano de obra). * Los ensambles del eje tienen una Garantía limitada de 3 años (Piezas y mano de obra, primer y segundo año; piezas solamente, tercer año). * Cualquier producto Scag que se utilice para alquiler está cubierto por una garantía de 90 días.
El cortacésped Scag, incluida cualquier pieza defectuosa, debe ser llevado a un distribuidor autorizado de Scag dentro del período de garantía. Los gastos incurridos en la entrega del cortacésped al distribuidor para que se realice el trabajo bajo garantía, así como los gastos de devolución del cortacésped al propietario después de la reparación, estarán a cargo del propietario. La responsabilidad de Scag se limita a la realización de las reparaciones requeridas y ninguna reclamación por incumplimiento de las obligaciones de garantía será causa de cancelación o revocación del contrato de venta del cortacésped Scag.
Esta garantía no cubre ningún cortacésped que haya sido sometido a uso indebido, descuido, negligencia o accidente, o que se haya operado de manera distinta a la especificada en el manual del operador . La garantía no será de aplicación en ningún caso
de daño ocasionado al cortacésped como consecuencia de mantenimiento inadecuado o a cualquier cortacésped o piezas que no se hayan ensamblado o instalado de acuerdo con las especificaciones del manual del operador o el manual de montaje. La garantía no cubre ningún cortacésped que haya sufrido alteraciones o modificaciones que hayan afectado su funcionamiento o durabilidad. Asimismo, la garantía no se extiende a reparaciones necesarias por el desgaste normal o por el uso de piezas o accesorios que, según criterio razonable de Scag, sean incompatibles con el cortacésped Scag o afecten la operación, funcionamiento o durabilidad de éste.
Scag Power Equipment se reserva el derecho de modificar o mejorar el diseño de cualquier cortacésped sin tener por ello obligación alguna de modificar cualquier cortacésped fabricado con anterioridad. Cualquier otra garantía implícita se limita a un
período de garantía de dos (2) años o noventa (90) días en el caso de cortacéspedes destinados a alquiler. Por consiguiente, se rechaza en su totalidad cualquier garantía implícita, incluidas las garantías de comerciabilidad, adecuación para un fin determinado, o de otro tipo, después de la finalización del correspondiente período de garantía de dos años o noventa días. La obligación de Scag en virtud de la presente garantía se limita estricta y exclusivamente a la reparación o el reemplazo de piezas defectuosas, y Scag no asume ni autoriza a ningún otro a asumir en su lugar ninguna otra obligación. La limitación antes mencionada no será de aplicación en aquellos estados en los que no esté permitida la limitación del período de validez de una garantía implícita.
Scag no asume responsabilidad alguna por daños incidentales, consecuentes ni de cualquier otro tipo, incluyendo, pero sin limitarse a, gasto de gasolina, gasto de entrega del cortacésped a un distribuidor autorizado Scag y gasto de su devolución al propietario, tiempo de viaje del mecánico, cargos por comunicaciones telefónicas o telegramas, alquiler de un producto similar durante el período en que se llevan a cabo las reparaciones bajo garantía, viajes, pérdida o daño de bienes personales, lucro
cesante, daños ocasionados por la pérdida del uso del cortacésped, daños por la pérdida de tiempo o cualquier otro inconveniente. La limitación o exclusión antes mencionada no será de aplicación en aquellos estados en los que no esté permitida la exclusión o limitación de daños incidentales o consecuentes. La presente garantía le otorga derechos legales específicos, aparte de los derechos de los que usted goza, según el estado.
Page 71
39
-NOTA-
de la pintura. con una cera automotriz para una máxima protección distribuidor autorizado Scag. Encere el cortacésped pintura de retoque Scag (N/P 48521) disponible en su
4. Repare las superficies de metal dañadas con la
vinilo/caucho para limpiar el asiento.
3. Use una solución suave de jabón o un limpiador de
3. Reinstale la criba de desechos en el radiador.
comprimido para retirar los desechos. motor caliente con agua; sólo use aire y límpielo con aire comprimido. Jamás rocíe un Revise si el radiador tiene demasiados desechos
con una manguera de agua.
2. Limpie la criba de desechos con aire comprimido o
1. Tire de la criba de desechos para retirarla.
gafas de seguridad al usar aire comprimido. Para evitar daños personales, siempre use
PRECA UCIÓN:
de desechos del radiador. Después de cada día de operación, retire y limpie la criba
radiador B. Limpieza de la criba de desechos del
2. No rocíe los componentes eléctricos.
automotrices. No use limpiadores a presión. plataforma de corte. Use agua fría y limpiadores
1. Después que cada uso, lave el cortacésped y la
-NOTA-
comprimido. está caliente. No lave el motor; use aire No lave ninguna parte del equipo mientras
adecuado reemplazo del refrigerante. su distribuidor Scag para información sobre el horas de operación o cada año. Consulte con refrigerante debe ser reemplazado cada 500 El sistema refrigeración debe ser purgado y el
detenga. abajo y gírela en el sentido del reloj hasta que se
3. Coloque la tapa del radiador. Presione la tapa hacia
PRECA UCIÓN:
Figura 7-10 Nivel del refrigerante
030467-13 SP
7.13 CUERPO, PLATAFORMA Y TAPICERÍA
ajustar o reemplazar la correa. presión. Consulte con su distribuidor Scag si requiere ventilador . La correa debe desviarse 1/2" con 10 libras de Revise periódicamente la tensión de la correa del
solamente) ventilador (motores enfriados por líquído C. Verificación de la tensión de la correa del
del cuello del llenador Llenar hasta el fondo
Sección 7
Page 72
38
refrigerante. saber la relación adecuada de la mezcla del Consulte las instrucciones del fabricante para
-NOTA-
de relleno, como se muestra en la Figura 7-10. de refrigerante debe llegar hasta el fondo del orificio
2. Revise visualmente el nivel del refrigerante. El nivel
para retirarla. tapa hacia abajo y gírela contra el sentido del reloj permita que se libere cualquier presión. Presione la contra del sentido del reloj hasta la primera parada y
1. Retire la tapa del radiador girándola lentamente en
de operación. El nivel del refrigerante debe revisarse antes de cada día
390S0161 SP
DE CORTE
DE LA PLATAFORMA
CAJA DE CAMBIOS
lubricante tiene bajo nivel, agregue lubricante SAE inferior del agujero del tapón de revisión. Si el visualmente que el nivel del lubricante llegue al borde de cambios (vea la Figura 7-9). Inspeccione
2. Limpie y retire el tapón de revisión del lado de la caja
plataforma de corte. para obtener acceso a la caja de cambios de la
1. Baje la plataforma de corte a su posición más baja
operación o cada dos semanas, lo que ocurra primero. de corte (Figura 7-9) debe revisarse cada 100 horas de El nivel de fluido en la caja de cambios de la plataforma
Figura 7-9 Caja de cambios de la plataforma de corte
REVISIÓN TAPÓN DE
A. V erificación del nivel del refrigerante
radiador. el motor se enfríe antes de retirar la tapa del Para evitar quemaduras, siempre permita que
ADVERTENCIA:
7.12 SISTEMA DE REFRIGERACIÓN
revisión y apriete firmemente. del agujero del tapón de revisión. Coloque el tapón de cambios hasta que esté a nivel con la parte inferior través del agujero del tapón de revisión en la caja de
3. Coloque el tapón y agregue lubricante SAE 80W90 a
deséchelo adecuadamente.
2. Retire el tapón, drene el lubricante en el recipiente, y
de drenaje de la caja de cambios. cambios de la plataforma de corte y ubique el tapón
1. Coloque un recipiente adecuado debajo de la caja de anualmente, lo que ocurra primero.
plataforma de corte luego de 500 horas de operación o Se debe cambiar el lubricante de la caja de cambios de la
PRECA UCIÓN:
B. Cambio de lubricante
tapón de revisión y apriete firmemente. inferior del agujero del tapón de revisión. Coloque el la caja de cambios hasta que esté a nivel con la parte 80W90 a través del agujero del tapón de revisión en
darle servicio. de la plataforma de corte se enfríe antes de operación. Permita que la caja de cambios puede alcanzar altas temperaturas de La caja de cambios de la plataforma de corte
A. V erificación del nivel de lubricante PLATAFORMA DE CORTE
7.11 CAJA DE CAMBIOS DE LA
Ruedas motrices .............................. 12 PSI
Ruedas locas ...................................Llantas macizas
horas de operación o diariamente. Verifique las presiones de las llantas después de cada 8
7.10 LLANTAS
Sección 7
Page 73
37
P
perno en el agujero de la cuchilla. arandela plana en el perno de la cuchilla y deslice el
4. Para instalar la nueva cuchilla de corte, coloque la
frontal de la máquina. corte se tendrá que levantar ligeramente la parte Para quitar el perno de la cuchilla del eje de
-NOTA-
390S0160 S
DE CORTE
CUCHILLA
ESPACIADOR DE
PERNO HEXAGONAL
CUCHILLA DE CORTE
Figura 7-8). las cuchillas con un apriete de 75 lbs-pie. (Vea la en la parte superior del eje de corte. Evite el giro de
6. Instale la tuerca hexagonal en el perno de la cuchilla
introduzca el perno en el eje de corte.
5. Instale el espaciador en el perno de la cuchilla e
Figura 7-8 Reemplazo de la cuchilla
ARANDELA
DEL EJE CONJUNTO
del eje. (Figura 7-8). Quite la cuchilla de corte, el perno y el espaciador y quite la tuerca del perno de fijación de la cuchilla. 9212, para ayudarlo a asegurar las cuchillas de corte) (Use la herramienta opcional Blade Buddy , N/P
3. Asegure las cuchillas de corte para evitar que giren,
plataforma. más alta de altura de corte para evitar que caiga la más alta. Coloque el pin de amarre en la posición
2. Levante la plataforma del cortacésped a la posición
cuchillas.
1. Quite la llave de encendido antes de reemplazar las
manos y ojos al trabajar con cuchillas de corte. Siempre lleve la protección apropiada para
ADVERTENCIA:
C. Reemplazo de la cuchilla
CABEZA HEXAGONAL
PERNO / TUERCA DE
cuchillas usted mismo. herramientas especiales si prefiere balancear sus autorizado Scag para balancear la cuchilla o por desgaste prematuro. Consulte con su distribuidor desbalanceadas, puede producirse vibración y
DE CORTE
PLATAFORMA
EJE
HEXAGONAL 75 LB-PIE TORQUE DE TUERCA
SGB033 SP
del ancho de la cuchilla
X NO debe exceder 1/3
X
Figura 7-7 Afilado de la cuchilla
30
2. Revise el balance de la cuchilla. Si las cuchillas están
la plataforma. aleta de izamiento hacia la parte superior de Asegúrese de que la cuchilla se instale con la
NOTA-
la cuchilla Mantenga el ángulo de
No corte
Sección 7
Page 74
36
caiga la plataforma. posición más alta de altura de corte para evitar que
del borde de corte para mantener el filo. original. Vea la Figura 7-7. Sólo afile la parte superior
1. Afile el borde de corte en el mismo bisel que el
la cuchilla. NO afile las cuchillas más de 1/3 del ancho de
-NOTA-
posiciónmás alta. Coloque el pin de amarre en la
2. Levante la plataforma del cortacésped a la
las cuchillas.
1. Quite la llave de encendido antes de dar servicio a
A. Inspección de la cuchilla
7.9 CUCHILLAS DE CORTE
quemar la cuchilla. cuchilla. Si usa una esmeriladora, puede Si es posible, use una lima para afilar la
-NOTA-
B. Afilado de las cuchillas
operación o semanalmente, lo que ocurra primero. verifique las correas después de cada 40 horas de su correcta alineación y revisar su desgaste. Después, primeras 2, 4, 8 y 10 horas de operación, debe verificarse resortes y son auto tensionantes, pero después de las Todas las correas de transmisión están cargadas por
7.8 CORREAS DE TRANSMISIÓN
la cuchilla. un desgaste adicional del motor y del eje de velocidad de corte del cortacésped y causa corte de césped, sino que disminuye la cuchillas desafiladas no sólo produce un mal Mantenga afiladas las cuchillas. Cortar con
-NOTA-
afilarlas. Vea “Reemplazo de la cuchilla”. tiene muescas, debe afilarse. Quite las cuchillas para
4. Si el borde de corte de una cuchilla está desafilado o
original para garantizar seguridad. Siempre reemplácela con una cuchilla Scag nunca suelde una cuchilla rota o rajada. No trate de enderezar una cuchilla doblada, y
ADVERTENCIA:
cable negativo al poste negativo de la batería. cable positivo al poste positivo de la batería y luego el
2. Cuando conecte los cables del puente, conecte el
puente, debe tener un sistema de tierra negativo. voltios. Si se usa un vehículo para el arranque por
1. La batería auxiliar de arranque debe ser de 12
C. Arranque por puente
el enfriamiento. debe reducirse o detenerse temporalmente para permitir temperatura excede 52°C (125°F), la tasa de carga electrolito o excesiva producción de gas, o si la caliente (encima de 125° F). Si se produce derrame de arrojan demasiado electrolito o si la batería no está muy satisfactorias si no provocan excesivos gases, si no Las tasas de carga entre 3 y 50 amperios son
Sección 7
ADVERTENCIA:
que ser reemplazadas. las cuchillas de corte parecen estar dobladas, tendrán
3. Verifique que las cuchillas de corte estén rectas. Si
manos y ojos al trabajar con cuchillas de corte. Siempre lleve la protección apropiada para
durante la carga. puede disipar los gases producidos espacio bien ventilado de modo que se EXPLOSIVOS. Cargue la batería en un LAS BATERÍAS PRODUCEN GASES
ADVERTENCIA:
Page 75
35
las placas en todas las celdas. antes de cargarla y asegúrese de que el electrolito cubre Siempre que sea posible, quite la batería del cortacésped
de conectar un cargador. causar lesiones. Permita que la batería se entibie antes NO cargue una batería congelada. Puede estallar y
baterías. de recargar la batería y se necesitará un cargador de período largo de tiempo, el alternador puede no ser capaz Si la batería se ha descargado completamente por un tendrá problemas para mantener la carga de la batería. Bajo condiciones normales el alternador del motor no
instrucciones específicas. Consulte el manual del cargador de batería para
Carga de la batería
ADVERTENCIA:
apropiada y use gafas de seguridad. lejos de las baterías. Proporcione ventilación Mantenga los arcos, las chispas y las llamas produzcan humo cerca de las baterías. cargar baterías, NO USE materiales que lesiones personales al revisar, probar o inflamables y explosivos. Para evitar Las baterías plomo-ácido producen gases
ELECTROLITO DE BATERÍA
PRIMEROS AUXILIOS PARA
ADVERTENCIA:
que induzcan al vómito. contacto interno, NO proporcione líquidos atención médica inmediatamente. En caso de huevos batidos, o aceite vegetal. Obtenga agua. Continúe con leche de magnesia, INTERNO — Beba grandes cantidades de
médica inmediatamente. durante 15 minutos y obtenga atención OJOS — Enjuague con agua al menos
CONTACTO EXTERNO — Enjuague con agua.
-NOTA-
primeros auxilios. líquido, siga primero las sugerencias de ninguna dirección. Si ocurre contacto con el incline ninguna batería más de 45° en apropiado cuando manipule baterías. NO con la ropa. Use equipo de protección el contacto del líquido con los ojos, la piel, o GRAVES QUEMADURAS QUÍMICAS. Evite sulfúrico que es TÓXICO y puede causar El líquido de la batería contiene ácido
7.7 BATERÍA
recomienda el fabricante del motor .
3. Limpie o reemplace el filtro de aire como
2. Quite el filtro de aire e inspecciónelo.
costado. aire. Quite la cubierta del filtro de aire y déjela a un cubierta del filtro de aire a la cámara del filtro de
1. Desenganche las abrazaderas que aseguran la
veces al día para prevenir daños al motor. necesario verificar el elemento una o dos En condiciones de mucho polvo, puede ser
propietario del motor para saber el octanaje apropiado. reemplace el elemento si es necesario. Vea el manual del horas de operación o cada mes, lo que ocurra primero, y Inspeccione y limpie el filtro de aire después de cada 100 determina los períodos de servicio del filtro de aire. Para cualquier filtro de aire, el ambiente de operación
filtro de aire
A . Limpieza y/o reemplazo del elemento del
7.6 FILTRO DE AIRE DEL MOTOR
Sección 7
Page 76
ADVERTENCIA:
34
sistema de combustible de la bomba. Equipment autorizado debe dar servicio al Sólo un distribuidor de Scag Power bomba al motor se encuentra a alta presión. El sistema de combustible que va de la
la manguera de combustible con las dos abrazaderas. que esté instalado en la dirección correcta. Asegure
2. Instale un nuevo filtro de combustible. Asegúrese de
de combustible. Retire el filtro de combustible. que aseguran el filtro de combustible a la manguera
1. Cierre la válvula de corte. Quite las dos abrazaderas
anualmente, lo que ocurra primero. (Figura 7-6) después de cada 500 horas de operación o Se debe reemplazar el filtro de combustible en línea
combustible en línea B. Reemplazo de los elementos del filtro de
firmemente.
10. Coloque nuevamente la tapa de gasolina y apriete
inmediatamente.
9. Si derrama combustible en la ropa, cámbiesela
posición abierta. No utilice un dispositivo que bloquee la boquilla en recipiente hasta terminar de llenar el combustible. tanque de combustible o con la abertura del
8. Mantenga la boquilla en contacto con el borde del
dispensador de gasolina. portátil en lugar de usar una boquilla de un es posible, añada el combustible con un recipiente abastézcala de combustible en el terreno. Si esto no
7. Retire la máquina del camión o del remolque y
combustible. terreno lejos de su vehículo antes de abastecerlos de plástico. Siempre coloque los recipientes en el un camión o remolque que tenga forro de material
6. Nunca llene recipientes dentro de un vehículo ni en
aparatos. luz piloto, como de un calentador de agua u otros combustible donde haya una llama abierta, chispa o
5. Nunca almacene el cortacésped o el recipiente de
techo ni en un remolque cerrado.
4. Nunca abastezca de combustible al cortacésped bajo
de combustible. Permita que el motor se enfríe antes de abastecerlo combustible con el motor en funcionamiento.
3. Nunca retire la tapa de la gasolina ni agregue
2. Use solamente un recipiente aprobado para gasolina.
STT99FF-1 SP
arriba y abajo) (con abrazaderas Filtro de combustible
Sección 7
Figura 7-6 Filtro de combustible
fuentes de ignición.
1. Apague todos los cigarrillos, puros, pipas y otras explosivos.
es extremadamente inflamable y los vapores son tenga mucho cuidado al manipular gasolina. La gasolina Para evitar lesiones personales o daños a la propiedad,
dañará severamente el motor. NO use combustible E85. El uso del combustible E85
10% de Etanol. de plomo con un octanaje mínimo de 87 y un máximo de rellenador. No llene demasiado. Use gasolina limpia, libre operación hasta 1 pulgada debajo del cuello del Llene el tanque de combustible al inicio de cada día de
A. Llenado del tanque de combustible
Page 77
33
Figura 7-4 V arilla de aceite del motor
tanque de combustible y rellenar . cortacésped se enfríe antes de quitar la tapa del Para evitar quemaduras, permita que el
390S0156 SP
PRECA UCIÓN:
7.5 SISTEMA DE COMBUSTIBLE DEL
del operador del motor para instrucciones. o cada mes, lo que ocurra primero. Consulte el manual reemplace el filtro de aceite cada 200 horas de operación reemplace el filtro de aceite del motor. Después, Después de las primeras 20 horas de operación,
C. Cambio de filtro de aceite del motor
de aceite
Figura 7-5 Ubicación del tapón de drenaje y del filtro
STT99CEC SP
DRENAJE
TAPÓN DE
ACEITE DEL MOTOR
VARILLA MEDIDORA DE
para motor SAE 20W50. cuello del rellenador . Si es necesario, agregue aceite Debe estar a 3" pulgadas desde la parte superior del
3. V erifique el nivel de aceite en el tanque hidráulico.
cinco minutos. palanca de control de velocidad en neutro durante
2. Opere el motor a la velocidad de vacío con la
RELLENADOR DE ACEITE DEL MOTOR
con este cortacésped para instrucciones. Consulte el manual del operador del motor proporcionado operación o mensualmente, lo que ocurra primero. Después, cambie el aceite después de cada 100 horas de aceite del cárter y reemplace el filtro de aceite. Después de las 5 primeras horas de operación, cambie el
B. Cambio de aceite del cárter
este cortacésped. en el manual del operador del motor proporcionado con cada 8 horas de operación o diariamente como se indica El nivel del aceite del motor se debe verificar después de
A. V erificación del nivel de aceite del cárter
7.4 ACEITE DEL MO TOR
solamente. aceite limpio de motor e instálelo. Apriételo a mano deséchelo adecuadamente. Llene el nuevo filtro con
1. Quite el elemento del filtro de aceite (Figura 7-3) y
horas de operación o anualmente, lo que ocurra primero. El filtro de aceite se debe cambiar después de cada 500
Figura 7-3 Filtro de aceite hidráulico
390S0155-1 SP
HIDRÁULICO FILTRO DE ACEITE
hidráulico C. Cambio del elemento del filtro de aceite
Sección 7
Page 78
32
Figura 7-2 Depósito de aceite hidráulico
depósito. Si es necesario, agregue aceite al depósito. durante dos minutos. Verifique el nivel de aceite en el el motor y conduzca hacia adelante y hacia atrás
5. Reemplace la tapa de relleno del depósito. Arranque
rellenador con aceite para motor SAE 20W50.
4. Llene el depósito a 3" de la parte superior del
describe en la sección C en la próxima página. debe cambiar el filtro de aceite tal como se Antes de rellenar el depósito de aceite hidráulico,
-NOTA-
esté ajustado. de la base del filtro de aceite y asegúrese de que
3. Vuelva a instalar el tapón de drenaje en la conexión
apropiadamente. Permita drenar el fluido en el recipiente y deséchelo en la base del filtro de aceite. (Vea la Figura 7-2). hidráulico. Retire el tapón de drenaje de la conexión aceite hidráulico. Quite la tapa del depósito de aceite
2. Coloque un recipiente adecuado debajo del filtro de
STT99HOR-1 SP
aceite hidráulico Depósito de
3. Limpie la tapa de relleno y tape el depósito.
depósito de aceite puede causar pérdidas de aceite). 20W50. NO llene demasiado; (llenar demasiado el Si el fluido está bajo, agregue aceite para motor una cinta de medición limpia para verificar el nivel. Si el nivel no se puede determinar visualmente, use pulgadas de la parte superior del cuello del rellenador. aceite hidráulico debe estar por lo menos a 3"
2. V erifique visualmente el nivel de aceite hidráulico. El
Sección 7
detenga el motor y quite la llave de encendido.
1. Estacione el cortacésped en una superficie plana,
presencia de agua o se percibe un olor rancio. El aceite hidráulico se debe cambiar si se nota la
-NOTA-
-IMPORTANTE-
indica habitualmente la presencia de agua. un posible recalentamiento del aceite y un color lechoso Un color negro y/o un olor rancio indican generalmente debe cambiar si se ha vuelto de color negro o lechoso. forma anual, lo que ocurra primero. El aceite también se El aceite hidráulico se debe cambiar cada 500 horas o en
B. Cambio de aceite hidráulico
depósito de aceite hidráulico. alrededor de la tapa del depósito. Quite la tapa del
1. Limpie la suciedad y las sustancias contaminantes de
corríjalas inmediatamente. manera constante, revise si existen pérdidas y Si el nivel de aceite se encuentra bajo de
máquina o mensualmente, lo que ocurra primero. aceite después de cada 200 horas de operación de la las primeras 10 horas de operación. Luego, verifique el El nivel del aceite hidráulico se debe verificar después de
A. V erificación del nivel de aceite hidráulico
7.3 SISTEMA HIDRÁULICO
Page 79
31
3
1
5
4
6
2
1
7
4
8
2
9
3
8
Figura 7.1 Lubricación de puntos de conexión
STT-EFI Grease Points
(500 HORAS/ANUALMENTE) GRASA DE CHASIS
(200 HORAS/MENSUALMENTE) GRASA DE CHASIS
(100 HORAS/CADA DOS MESES) GRASA DE CHASIS
(40 HORAS/SEMANALMENTE) GRASA BLANCA DE LITIO MP 2125
LUBRICANTE / INTERVALOT
CONEXIONES DE GRASA DE LUBRICACIÓN
Sección 7
Page 80
30
Lidok EP #2 encontrada en almacenes industriales Shell Alvania #2 encontrada en estaciones de servicio Shell
Timken Lithium Multi-Use #2 encontrada en almacenes industriales
+ Grasas compatibles: Mobilix #2 encontrada en estaciones de servicio Mobil tapa de grasa.
instalar la tapa de grasa. Se recomienda usar la herramienta especial número de parte 47007 para la instalación de la grasa en la parte superior de la extensión de la rueda libre. Quite el engrasador y vuelva a instalar el tapón. Vuelva a 482028-01, e instale un engrasador estándar (n/p 48114-06). Aplique grasa a la conexión hasta que aparezca nueva * PROCEDIMIENTO: Retire la tapa de grasa, número de parte 481559. Quite el tapón, número de parte
la plataforma de corte
9 Manguito deslizante del eje motriz de 40 horas/semanalmente Grasa de chasis 1
la plataforma de corte
8 Uniones en U del eje motriz de 200 horas/mensualmente Grasa de chasis 2 7 Mango del freno 200 horas/mensualmente Grasa de chasis 1 6 Eje de la plataforma de corte 40 horas/semanalmente +Grasa blanca de litio MP 2125 3 5 Eje PTO 40 horas/semanalmente +Grasa blanca de litio MP 2125 1 4 Brazos de empuje de plataforma de corte 100 horas/cada dos semanas Grasa de chasis 2 3 Balancines de plataforma de corte 100 horas/cada dos semanas Grasa de chasis 4 2 Rodamientos de la rueda loca 100 horas/mensualmente Grasa de chasis 2 1 Pivote de rueda loca * 500 horas/anualmente Grasa de chasis 2
UBICACIONES
Nº DE
Vea el párrafo 7.12
Vea el párrafo 7.11 Vea el párrafo 7.3 20W50
Use aceite SAE Vea el párrafo 7.3
Vea el párrafo 7.5 Vea el párrafo 7.3
Vea el párrafo 7.4
LUBRICANTE
LUBRICACIÓN
INTERV ALO DE
X
Cambie el refrigerante (sólo Kawasaki)
cambios de la plataforma de corte
X
Reemplace el lubricante en la caja de
X
Reemplace el filtro de aceite hidráulico
aceite hidráulico Drene el sistema hidráulico y reemplace el
X
Reemplace el filtro de combustible del motor
X V erifique el nivel del aceite hidráulico Cambie el filtro de aceite del motor
V erifique que la tornillería esté bien ajustada
Aplique grasa a las conexiones Vea el párrafo 7.2
X
X
X
X
LUBRICACIÓN
(VEA LA FIGURA 7-1, PÁGINA 29)
7.2 LUBRICACION - TABLA DE LUBRICACIÓN DE CONEXIÓN DE GRASA
Observaciones
Sección 7
Procedimiento
8 40 100 200 500
HORAS
10) (Primeros Uso inicia
(CONTINUACIÓN) TABLA DE MANTENIMIENTO - INTERVALOS DE SERVICIO RECOMENDADOS
Page 81
29
suciedad
* Realice con más frecuencia estos procedimientos de mantenimiento bajo condiciones extremas de polvo o
Vea el párrafo 7.11 Vea el párrafo 7.6 Vea el párrafo 7.4 Vea el párrafo 7.2 Vea el párrafo 7.8
Vea el párrafo 7.7
Vea el párrafo 4.2 Vea el párrafo 2.5 Vea el párrafo 7.12
Vea el párrafo 7.10 Vea el párrafo 7.2 Vea el párrafo 7.9
Vea el párrafo 7.13
la plataforma de corte Verifique el lubricante en la caja de cambios de
*Limpie el elemento del filtro de aire Cambie el aceite del motor Aplique grasa a las conexiones
Verifique la correcta alineación de las correas
los bornes y los cables de la misma V erifique el nivel de electrolito de la batería, limpie
Verifique el sistema de bloqueo de seguridad
desgaste o deterioro Revise si el cinturón de seguridad presenta
V erifique el nivel del refrigerante (sólo Kawasaki)
Revise la presión de las llantas Aplique grasa a las conexiones
Verifique el estado de las cuchillas
*Limpie el cortacésped
X X
X X
X
X
X
X X
X
X
X
X Vea el párrafo 7.4 Vea el párrafo 7.12
Vea el párrafo 7.4
Vea el párrafo 7.8
Vea el párrafo 7.3
Observaciones
mangueras hidráulicas Vea el párrafo 2.5 T enga mucho cuidado al verificar las
Procedimiento
Verifique el nivel de aceite del motor
(Kawasaki y Briggs) V erifique el nivel del refrigerante
en las mangueras hidráulicas Verifique que no haya fugas
Cambie el aceite del motor y el filtro
Verifique la correcta alineación de todas las correas V erifique el nivel del aceite hidráulico
Verifique que toda la tornillería esté bien ajustada
X
8 40 100 200 500
HORAS
X
X
X
X
X X
(Primeros 10)
Uso inicial
7.1 TABLA DE MANTENIMIENTO - INTERVALOS DE SERVICIO RECOMENDADOS
(Primeros 20)
MANTENIMIENTO
Sección 7
Page 82
28
Figura 6-9 Ajuste del deflector de corte personalizado
Altura (pulgadas) 3-1/2” 4” 4-1/2” Ranura "B" Orificio 2 Orificio 3 Orificio 4
Altura (pulgadas) 3-3/4” 4-1/4” 4-3/4” 5-1/4” Ranura "A" Orificio 1 Orificio 2 Orificio 3 Orificio 4
Ubicación de accesorios de montaje
Ranura de montaje seleccionada
Ajuste del deflector de corte personalizado
B A
4
B
A
4
3
2
1
3
2
1
Sección 6
los tornillos con un torque de 39 pies-lb
4. Vuelva a instalar los accesorios de montaje. Apriete
posición deseada. (Vea las Figuras 6-9).
3. Mueva el deflector de corte personalizado a la
acuerdo con el tamaño de la plataforma de corte. ubicación de los accesorios puede variar de ilustraciones es sólo para referencia. La
corte personalizado a la plataforma de corte.
2. Quite los accesorios que aseguran el deflector de
transporte.
1. Coloque la plataforma de corte en posición de
La ubicación de los accesorios usados en las
-NOTA-
Para ajustar la altura del deflector de corte personalizado:
Page 83
27
390S0175-1 SP
1/4"
plataforma de corte. (recogida de hojas) y reducirá los “soplos” en la de 4-3/4" ó 5-1/4" mejorará el corte en otoño Página 28). La colocación del deflector en el ajuste
C. Posición de 4-3/4" ó 5-1/4" - (Vea la Figura 6-9,
de desempeño de corte en todos los tipos de césped. propósito general. Esto le da la mejor combinación (Vea la Figura 6-9, Página 28). Para cortes de
B. Posición de 4" (ajuste de fábrica), 4-1/4" ó 4-1/2" -
cortar. Página 28). Para césped muy alto, tieso y difícil de
A. Posición de 3-1/2" ó 3-3/4" - (Vea la Figura 6-9,
390S014A-2 SP
diferentes para el desempeño óptimo. El deflector se puede colocar en siete (7) posiciones plataforma para el tipo de césped que se está cortando. personalizar en forma precisa el desempeño de la personalizado puede levantarse o bajarse para superior en cualquier tipo de césped. El deflector entregar un óptimo flujo de aire y un desempeño de corte El deflector de corte personalizado está diseñado para
Figura 6-8 Tope de la plataforma de corte
PLATAFORMA TOPE DE LA
contratuercas en la varilla de control. de corte. (Vea la Figura 6.8). Apriete las de la plataforma y la parte superior de la plataforma que haya un espacio de 1/4" entre el tope posterior
2. Gire la varilla de control (V ea la Figura 6.7) hasta
Figura 6-7 Ajuste de altura de la plataforma de corte
PEDAL DE AJUSTE DE ALTURA
Ajuste del deflector de corte personalizado
CUTTING
HEIGHT
6
5.5
5
4.5
4
3.5
3
2.5
2
fácilmente en la posición de transporte. la plataforma de corte se pueda bloquear Si se tuvo que realizar un ajuste, asegúrese que
-NOTA-
1.5
1
481543
AMARRE PIN DE
AFLOJE AQUÍ
plataforma. (Vea la Figura 6.7)
6.7) control de altura de la plataforma. (Vea la Figura 3", puede realizarse un ajuste utilizando la varilla de
extremos de la varilla de control de la altura de transporte. Afloje las contratuercas en ambos
1. Coloque la plataforma de corte en posición de
la cuchilla de corte. Si la medida no se encuentra en
4. Verifique la medida desde el suelo hasta la punta de
apropiadamente. superficie plana y a nivel y que las llantas estén infladas
desplace a la posición de la altura de corte de 3". de la posición de transporte y permita que se indicador de la altura de corte. Libere la plataforma colocando el pin de amarre en la posición 3" en el
3. Verifique la altura de corte de la plataforma de corte
plataforma, asegúrese que el cortacésped esté en una en el indicador. Para verificar la altura apropiada de la para asegurar que la misma corte en la altura señalada El ajuste de la altura de la plataforma de corte se realiza
Altura de la plataforma de corte
Sección 6
Page 84
26
390S0174-1 SP
AJUSTE AQUÍ CONTRATUERCA
Figura 6-6 Ajuste del nivel de la plataforma de corte
apropiada. asegurar la plataforma de corte en la posición
3. Apriete las dos tuercas elásticas de tope para
máquina. sea igual que la medida del lado derecho de la la distancia desde la parte inferior de la misma al piso ajuste para ajustar la plataforma de corte hasta que perno hacia arriba o hacia abajo en el soporte de
2. Afloje las dos tuercas elásticas de tope. Regule el
Figura 6-5 Ajuste del nivel de la plataforma de corte
AQUÍ AFLOJE
mencionados anteriormente. de corte como se explicó en los procedimientos
AQUÍ AJUSTE
plataforma oscila, debe reajustar la plataforma las cuatro cadenas no están bajo tensión y la plataforma de corte deben estar tensionadas. Si corte, las cuatro cadenas suspendidas de la Para evitar la oscilación de la plataforma de
-NOTA-
(Vea la Figura 6.5) de corte, ubique el soporte de ajuste de la misma
1. En el lado frontal del lado izquierdo de la plataforma
bloqueo. de la plataforma de corte. Apriete ambas tuercas de inclinación adecuada en los lados derecho e izquierdo
6.6) gire las varillas de ajuste hasta que se alcance la
2. Usando una llave en la contratuerca (vea la Figura
ajustar como sigue: son diferentes, el nivel de la plataforma de corte se debe Ambas medidas deben ser iguales. Si las dos medidas de corte hasta el piso en el lado izquierdo de la máquina. revise la distancia desde la parte inferior de la plataforma
ajuste. (Vea la Figura 6.6)
1. Afloje las tuercas de bloqueo en ambas varillas de de la plataforma debe ajustarse de la manera siguiente:
parte frontal de la plataforma no es igual, la inclinación izquierdo de la plataforma de corte. Si la medida en la plataforma. También realice estas medidas en el lado ser igual a la medida en la parte posterior de la medida en la parte frontal de la plataforma de corte debe las cadenas de suspensión de la plataforma de corte. La
inferior de la plataforma de corte hasta el piso. Luego de la máquina, verifique la distancia desde la parte altura de corte más común que usará. En el lado derecho apropiadamente y la plataforma de corte esté fijada en la superficie plana y nivelada, las llantas estén infladas nivel, asegúrese que el cortacésped esté en una para un desempeño apropiado de corte. Para verificar el La plataforma de corte debe ser plana de lado a lado
Nivel de la plataforma de corte
del lado derecho de la misma directamente en frente de de la plataforma de corte hasta el piso en el lado frontal corte. Luego verifique la distancia desde la parte inferior detrás de las cadenas de suspensión de la plataforma de lado derecho de la plataforma de corte directamente plataforma de corte hasta el piso en el lado posterior del Verifique la distancia desde la parte inferior de la
-NOTA-
las llantas estén infladas apropiadamente. cortacésped esté en una superficie plana y a nivel y que inclinación apropiada de la plataforma, asegúrese que el desempeño de corte apropiado. Para verificar la entre la parte frontal y posterior de la misma para un La inclinación de la plataforma de corte debe ser igual
Inclinación de la plataforma de corte
llantas estén infladas apropiadamente. plataforma de corte, asegúrese de que todas las Antes de proceder con los ajustes de la
de la plataforma de corte. procedimientos lo ayudarán a obtener el ajuste apropiado realizarse estos ajustes alguna vez, los siguientes altura se ajustan en fábrica. Sin embargo, si deben El nivel de la plataforma de corte, la inclinación y la
CORTE
6.6 AJUSTES DE LA PLATAFORMA DE
Sección 6
Page 85
25
condición, proceda de la manera siguiente: gira más rápido que la izquierda. Para ajustar esta izquierda, es una indicación de que la rueda derecha
2. Si a máxima velocidad el cortacésped se tira a la
describe en la página 24. neutral debe hacerse de la manera que se lentamente hacia adelante o hacia atrás, el ajuste explicó en el paso 1A, la máquina avanza Si después de realizar el ajuste tal como se
6-4, página 24) velocidad de la rueda de dicho lado. (Vea la Figura la bomba del lado izquierdo, disminuyendo la Esto causará que la varilla de control golpee menos estirar la varilla y apriete las tuercas de bloqueo. del lado izquierdo. Gire la varilla de control para en cada extremo de la varilla de control de dirección tuercas de bloqueo que aseguran las juntas de rótula control de dirección en la posición neutral. Afloje las
A. Detenga la máquina y coloque las palancas de
condición, proceda de la manera siguiente: gira más rápido que la derecha. Para ajustar esta derecha, es una indicación de que la rueda izquierda
1. Si a máxima velocidad el cortacésped se tira a la
máquina tirará al lado con la presión más baja. Si la presión de la llanta no es correcta, la de las llantas en las ruedas motrices es correcta. las ruedas locas giren libremente y que la presión Antes de proceder con este ajuste, asegúrese que
ADVERTENCIA:
consulte con su centro de servicio autorizado Scag. experimenta un frecuente desgaste o rotura de correas, desempeño apropiado de su cortacésped Scag. Si La alineación de la correa es importante para el
6.5 ALINEACIÓN DE LA CORREA
correcta alineación y el desgaste de las correas. auto tensionantes. Deben revisarse periódicamente la plataforma de corte están cargadas por resortes y son Todas las correas de transmisión y las correas de la
-NOTA-
el motor y retire la llave de encendido.
Antes de quitar cualquier guarda, apague
6.4 AJUSTE DE LA CORREA
centro de servicio autorizado Scag. motor. Si requiere cualquier ajuste, contacte con su Scag para asegurar la operación apropiada y eficiente del Estos ajustes deben ser realizados por su distribuidor
ACELERACIÓN Y ESTRANGULACIÓN
6.3 AUSTES DE LOS CONTROLES DE
-NOTA-
describe en la página 24. neutral debe hacerse de la manera que se lentamente hacia adelante o hacia atrás, el ajuste explicó en el paso 2A, la máquina avanza Si después de realizar el ajuste tal como se
-NOTA-
página 24) de la rueda del lado derecho. (Vea la Figura 6-3, la bomba del lado derecho, disminuyendo la velocidad Esto causará que la varilla de control golpee menos estirar la varilla y apriete las tuercas de bloqueo. del lado derecho. Gire la varilla de control para en cada extremo de la varilla de control de dirección tuercas de bloqueo que aseguran las juntas de rótula control de dirección en la posición neutral. Afloje las
A. Detenga la máquina y coloque las palancas de
PRECA UCIÓN:
PRECA UCIÓN:
realizar cualquier ajuste. componentes de transmisión se enfríen antes de quemaduras. Permita que el motor y los durante la operación, causando heridas por El motor y la unidad motriz pueden calentarse
comenzar a trabajar. todas las partes móviles se detengan antes de
antes de realizar cualquier ajuste. Espere que Detenga el motor y quite la llave del encendido
Ajuste de alineación
Sección 6
Page 86
24
390S0146 SP
390S0147-1 SP
AJUSTE AQUÍ
AFLOJE AQUÍ
AQUÍ
AFLOJE
dirección a mano izquierda Figura 6-4 Ajuste de la varilla de control de
STT99RHCRA SP
390S0149-1 SP
dirección a mano derecha Figura 6-3 Ajuste de la varilla de control de
AJUSTE AQUÍ
AFLOJE AQUÍ
AQUÍ
AFLOJE
necesario. carrera completa. Ajuste como lo considere golpeen el tope antes de que las bombas alcancen la
8. Compruebe que las palancas de control de dirección
neutral y ajuste de nuevo si es necesario.
7. Compruebe que las ruedas motrices permanezcan en
neutral. adelante y en reversa y regréselas a la posición
6. Accione las palancas de control de dirección hacia
rueda izquierda. (Vea la Figura 6-4).
5. Apriete las contratuercas y repita el proceso para la
(Vea la Figura 6-3). deje de moverse. Gire la varilla 1/2 vuelta adicional. varilla en sentido contrario hasta que la rueda motriz hasta que la rueda motriz gire hacia adelante. Gire la en la varilla de control de dirección y gire la varilla
4. Ajuste la rueda derecha aflojando las contratuercas
CONTROL
VARILLA DE
adelante o hacia atrás. y compruebe si la máquina se arrastra hacia
3. Opere el motor a la máxima velocidad de operación
libere el freno de estacionamiento.
2. Con un operador en el asiento, arranque el motor y
neutral de bloqueo. palancas de control de dirección estén en la posición descarga estén en la posición de operación y que las
1. Asegúrese de que las palancas de la válvula de
Ajuste neutral
alineación, Vea página 25). desplazarse hacia adelante. (Ajuste de cortacésped se tira a un lado o al otro al posición completamente hacia adelante y el
B. Las palancas del control de dirección están en la
Sección 6
Page 87
23
390S0152-1 SP
página 24). adelante o hacia atrás. (Ajuste neutral, vea la posición neutral y la máquina se arrastra hacia
A. Las palancas de control de dirección están en la
si: Se tendrán que realizar ajustes neutrales o de alineación
6.2 AJUSTES DE DESPLAZAMIENTO
Figura 6-2 Ajuste de la varilla de freno
AJUSTE AQUÍ
1-7/16”
AFLOJE AQUÍ
Figura 6-1 Ajuste del freno
Luz de 2" a 2-1/4"
contratuerca. (Vea la Figura 6-2). alcance la medida de 1-7/16" y apriete la el sentido del reloj para aumentarla) hasta que se reloj para reducir la compresión del resorte o contra
6. Gire el perno de ajuste en el sentido de las agujas del
Figura 6-2). final de la varilla del accionador de freno. (Vea la especificada, afloje la contratuerca en el extremo
5. Si la distancia no coincide con la medida
ser de 1-7/16". (Vea la Figura 6-2). al lado izquierdo de la máquina. La distancia deberá compresión del resorte entre las dos arandelas planas
4. Con el freno en la posición accionada, revise la
(Vea la Figura 6-1). Apriete las contratuercas. la varilla hasta que se alcance la distancia adecuada. extremos de la varilla de control del freno y girando ajuste aflojando las contratuercas en ambos
3. Si la distancia no es de la medida especificada,
distancia debe ser de 2" a 2-1/4" (Vea la Figura 6-1). bastidor y la parte inferior del mango del freno. La revise la distancia entre la parte superior del tubo del
2. Con la palanca de freno en la posición desconectada,
motrices. evitar que la máquina se mueva. Quite las ruedas evitar que caiga. Bloquee las ruedas locas para de la máquina. Levante la máquina y apóyela para
1. Coloque un gato de piso debajo de la parte posterior freno.
su distribuidor Scag para cualquier ajuste adicional de freno de estacionamiento apropiadamente, contacte con Si los procedimientos siguientes no permiten accionar el estacionamiento permitirá que el cortacésped se mueva. coloque en la posición “ENGAGE”; el freno de apenas la palanca del freno de estacionamiento se El acople del freno de estacionamiento debe ajustarse
AFLOJE AQUÍ
autorizado de Scag. apropiado del freno, contacte con su distribuidor Si este procedimiento no logra el ajuste
-NOTA-
8. Reemplace las ruedas motrices y pruebe el freno.
ADVERTENCIA:
graves. funcionamiento. P odrían causarse lesiones estacionamiento no está en correcto estado de No opere el cortacésped si el freno de
ESTACIONAMIENTO
6.1 AJUSTE DEL FRENO DE
máquina.
7. Repita los pasos del 4 al 6 en el lado derecho de la
AJUSTES
Sección 6
Page 88
22
autorizado Consulte con su distribuidor Scag
autorizado Consulte con su distribuidor Scag
autorizado Consulte con su distribuidor Scag
autorizado Consulte con su distribuidor Scag
SGB 025
Alojamiento de la plataforma doblado
plataforma de corte
Ancho de la
la trayectoria de corte
Falla del eje interno
través del ancho de Crestas inclinadas a
Área de montaje del eje doblada
SGB 024
Ancho de la
Montaje incorrecto del eje
Corte inclinado -
plataforma de corte
autorizado Consulte con su distribuidor Scag
Reemplace la cuchilla
Ajuste la inclinación y el nivel
Corte el césped una vez que se seque las condiciones del terreno
Disminuya la velocidad para ajustarse a dirección del corte plataforma de corte y/o cambiar la en el terreno, aumentar la altura de la Se puede tener que reducir la velocidad
nivel del corte y/o cambiar la inclinación y el plataforma de corte, cambiar la dirección en el terreno, aumentar la altura de la Se puede tener que reducir la velocidad
las condiciones del terreno Disminuya la velocidad para ajustarse a
Verifique y ajuste las presiones
Falla del eje interno
Cuchilla doblada
trayectoria de corte en el centro de la
Cuchillas mal montadas, disparejas
Césped mojado
Velocidad demasiado alta
T erreno rugoso
Corte demasiado bajo
Velocidad demasiado alta Baja presión de las llantas
SGB 022
Ancho de la
Corte lateral - Cresta
plataforma de corte
al terreno cortando muy cerca tierra o están cuchillas pegan en la Raspadoras - Las
Section 5
SOLUCIÓN
CAUSA
CONDICIÓN
SOLUCIÓN DE FALLAS (CONTINUACIÓN)
Page 89
21
Verifique el nivel y corrija
autorizado Consulte con su distribuidor Scag
Revise y ajuste la presión de las llantas
Revise y ajuste la presión de las llantas
SGB 023
Plataforma no nivelada lado a lado
incorrectamente Plataforma de corte montada
Ruedas disparejas
plataforma de corte
Ancho de la
de corte ancho de la trayectoria
Llantas con presión desigual
SGB 021
Ancho de la
Salientes inclinadas a lo
plataforma de corte
dirección del corte plataforma de corte y/o cambiar la en el terreno, aumentar la altura de la Se puede tener que reducir la velocidad
Afile la cuchilla autorizado
Consulte con su distribuidor SCAG autorizado
Consulte con su distribuidor SCAG Ajuste la inclinación y el nivel plataforma
Limpie la parte de abajo de la terreno
Monte la cuchilla con el filo hacia el
Reemplace la cuchilla
irregular volado o perfil ondulada, corte Apariencia baja y alta terreno disparejo -
T erreno disparejo
SGB 020
Ancho de la
Cuchilla desafilada
Área del eje doblada incorrectamente
Plataforma de corte montada (inclinación de la plataforma de corte)
Demasiado ángulo en la cuchilla plataforma de corte Césped acumulado debajo de la
Corte disparejo en
plataforma de corte
o perfil irregular ondulada, corte volado
Cuchilla montada invertida
Apariencia baja y alta terreno plano -
Levantador de la cuchilla desgastado
Corte disparejo en
SOLUCIÓN
CAUSA
CONDICIÓN
SOLUCIÓN DE FALLAS (CONTINUACIÓN) Sección 5
Page 90
20
Reemplace las cuchillas Corte el césped una vez que se seque
las condiciones del terreno Disminuya la velocidad para ajustarse a
plataforma Limpie la parte de abajo de la
de corte
plataforma
Ancho de la
SGB 019
de corte
plataforma
Ancho de la
Traslape insuficiente entre pasadas Aumente el traslape de cada pase
Cuchillas dobladas
SGB 018
plataforma de corte
Ancho de la
Césped mojado Velocidad demasiado alta
plataforma de corte Césped acumulado debajo de la
corte entre trayectorias de césped sin cortar Vetas - Franjas de
SOLUCIÓN
Ajuste la tensión de la correa
Opere el motor a su máxima RPM
Afile las cuchillas
Afile las cuchillas
Ajuste la tensión de la correa plataforma
Limpie la parte de abajo de la Afile las cuchillas
Corte el césped una vez que se seque las condiciones del terreno
Disminuya la velocidad para ajustarse a
Opere el motor a su máxima RPM
CAUSA
Correa patinando
Bajas revoluciones (rpm) del motor
Afilado incorrecto de las cuchillas
trayectoria de corte césped sin cortar en la
Cuchillas desafiladas o desgastadas
SGB 020
Correas patinando
Ancho de la
plataforma de corte Césped acumulado debajo de la
Cuchillas desafiladas, afilado incorrecto Césped mojado
Velocidad demasiado alta
Vetas - Franjas de
plataforma de corte
sin cortar ocasionales de césped
Bajas revoluciones (rpm) del motor
Largueros -Cuchillas
CONDICIÓN
Section 5
SOLUCIÓN DE FALLAS
Page 91
19
PERILLA
DE
TENSIÓN
PERILLA
DE TENSIÓN
PALANCA
DE ROTACIÓN
P
390S0140-2 S
2.5
2
1.5
1
481543
Figura 4-9 Ubicaciones del pedal de ajuste de la altura
UBICACIONES DEL PEDAL DE AJUSTE DE LA ALTURA
palanca.
A. Afloje la perilla de tensión en el conjunto de la aplique las siguientes instrucciones.
3. Si es necesario el ajuste de las palancas de dirección,
control total y comodidad. hacia adelante y hacia atrás para verificar que tenga motor apagado, mueva ambas palancas de dirección
2. Al encontrarse en la posición de operador con el
1. Coloque el asiento en la posición deseada.
CUTTING
HEIGHT
6
5.5
5
4.5
4
3.5
3
4.15 Ajuste de las palancas de dirección
podría dañar el remolque o el cortacésped.
del operador. Vea la Figura 4-9. (3) diferentes posiciones para la comodidad y control
3. El pedal de ajuste de altura se puede colocar en tres
total de la función. ajuste de altura para verificar que tenga el control motor apagado, presione hacia abajo el pedal de
6. Un giro de radio cero con un remolque conectado,
adicional para detenerse.
5. Desplácese lentamente y permita una distancia
pérdida de control. remolcado puede causar la pérdida de tracción y la
4. Nunca remolque en cuestas. El peso del equipo
2. Al encontrarse en la posición de operador con el peso remolcado 250 lbs (113 Kg).
1. Coloque el asiento en la posición deseada.
4.16 Ajuste del pedal de ajuste de altura
límite de peso para el equipo remolcado. Máximo
3. Siga las recomendaciones del fabricante para el
enganche.
Figura 4-8 Ajuste de las palancas de dirección
Sólo conecte el equipo remolcado en el punto de accesorio de enganche diseñado para remolcar.
2. Remolque sólo con una máquina que tenga un
remolcado.
1. Nunca permita niños ni otras personas en el equipo
opcional)
4.14 Remolque (accesorio de enganche
Figura 4-7 Palanca de liberación de la plataforma
390S0151-1 SP
palancas estén niveladas antes de operar. neutral de bloqueo y verifique que ambas as palancas de dirección fuera de la posición
D. Al encontrarse en la posición de operador, lleve l
en el lado opuesto.
C. Apriete la perilla de tensión y repita el proceso
5
5.5
6
HEIGHT
CUTTING
481543
1
1.5
2
2.5
3
3.5
4
4.5
funcionamiento. hacia atrás para lograr una óptima posición de
B. Gire la palanca de dirección hacia adelante o
DE LA PLATAFORMA PALANCA DE LIBERACIÓN
Sección 4
Page 92
390S0140-2 SP
3.5
3
2.5
2
1.5
1
481543
18
Figura 4-6 Ajuste de altura de corte
PEDAL DE AJUSTE DE ALTURA
corte. Si corta a una RPM más baja, las cuchillas de
7. Opere el motor a máxima aceleración para un mejor
desee recortar.
6. Use una baja velocidad de desplazamiento cuando
la altura deseada. para el primer pase y luego haga un segundo pase en veces. Levante el cortacésped al ajuste más alto
5. Cuando corte césped mojado o césped alto, corte dos
CUTTING
HEIGHT
6
5.5
5
4.5
4
descarga.
4. Mantenga limpios el cortacésped y la tolva de
AMARRE PIN DE
apariencia). Corte frecuentemente. menos del césped existente para obtener una mejor
plataforma a la altura deseada. (Figura 4-6). indicador de altura como una ayuda para ajustar la
alto. No corte el césped demasiado corto (corte 1/3 o
3. Corte el césped cuando esté seco y no demasiado
calcomanía de la altura de plataforma ubicada en el página 19). Libere lentamente el pedal. Hay una palanca de liberación de plataforma, (Figura 4-7, plataforma, manténgala en posición y levante la adelante la palanca de pie de la elevación de
ADVERTENCIA
de corte en la altura de corte deseada. Empuje hacia
3. Inserte el pin de amarre en el indicador de la altura
hasta que se asegure en su lugar. (Figura 4-6). completamente hacia adelante con su pie derecho
2. Empuje el pedal de pie de ajuste de la altura de corte
1. Desconecte la potencia a las cuchillas de corte.
DESCARGA, O SIN EL RECOGEDOR DE CÉSPED INSTALADOS. NO OPERE SIN EL EQUIPO MEZCLADOR DE PAJA DE LA TOLVA DE
propiedad debido a objetos lanzados. mismos para reducir la posibilidad de daños a la cerca de obstáculos, dirija la descarga lejos de los limpieza de los recortes de césped. Cuándo corte lateral lejos de aceras o de calles para minimizar la se encuentre sobre el mismo. Dirija la descarga hacia abajo el césped cortado y cualquier objeto que mantenerse en su posición más baja para desviar
el freno y luego ajuste la altura de corte. palancas en posición neutral de bloqueo, aplique potencia a las cuchillas de corte, ponga las del cortacésped estén girando. Desconecte la No ajuste la altura de corte cuando las cuchillas
2. La tolva de descarga no debe quitarse y debe
requiriendo potencia adicional del motor. resultado una mala apariencia del césped y desafilada desgarrará el césped, dando como
1. No corte con cuchillas desafiladas. Una cuchilla
ADVERTENCIA:
EL CÉSPED
4.12 RECOMENDACIONES PARA CORTAR
Section 4
ajustar la altura de corte: una altura de 1" hasta 6" en intervalos de 1/4". Para La plataforma del cortacésped puede ajustarse desde
4.13 AJUSTE DE LA ALTURA DE CORTE
los patrones en el mismo. cada vez que corte el césped para evitar estropear apariencia del césped. Varíe la dirección de la franja
8. Use el patrón de franjas alternas para mejorar la
para operarse a la máxima velocidad. corte desgarrarán el césped. El motor está diseñado
cortacésped. DRIVE y ajustadas a 7-10 pies/lb para operar el válvula de descarga deben ser regresadas a la posición mueve el cortacésped a mano. Las palancas de la Página 14). Desconecte el freno de estacionamiento y descarga en la posición FREE-WHEEL (Figura 4-2, motor encendido, coloque las palancas de la válvula de Para “rodar libremente” o mover el cortacésped sin el
DETENIDO CORTACÉSPED CON EL MOTOR
4.11 DESPLAZAMIENTO DEL
Page 93
17
Luego, reanude el corte normal. artículo semejante para sacar el material atascado. motor y quita la llave de encendido. Use un palo o
1. Si la tolva de descarga llega a atascarse, apague el
quitar el material atascado. sólo entonces use un palo u objeto semejante para una obstrucción, apague el motor y quite la llave y DESCARGA POR NINGÚN MOTIV O! Si ha ocurrido ¡NUNCA PONGA LAS MANOS EN LA TOLVA DE
CUCHILLAS GIRATORIAS
PELIGRO:
4.10 RETIRO DEL MATERIAL ATASCADO
si es necesario.
5. V erifique la presión de las llantas. Corrija la presión
combustible con combustible limpio. cortacésped se haya enfriado, llene los tanques de
4. Al final de cada día de operación y después de que el
de vacío.
4. Disminuya la velocidad del motor hasta la velocidad
3. Desconecte las cuchillas de corte
posición neutral.
2. Coloque las palancas de control de dirección en la
pendiente. nivel solamente. No estacione la máquina en una
1. Estacione el cortacésped en una superficie plana y a
CORTACÉSPEDES
4.8 ESTACIONAMIENTO DEL
5. Mantenga las llantas correctamente infladas.
pérdida de frenado o dirección. que las ruedas motrices se deslicen, causando a la parte delantera de la máquina y puede causar desplazarse bajando una cuesta. El peso se transfiere
4. Puede producirse una pérdida de tracción al
se incline hacia atrás. arranques repentinos pueden causar que la máquina
3. Evite arranques repentinos al subir una cuesta. Los
combustible y rellenar . se enfríe antes de quitar la tapa del tanque de Para evitar quemaduras, permita que el cortacésped
PRECA UCIÓN:
ajuste si es necesario. transmisión y cualquier señal de desgaste. Corrija y
3. Verifique la correcta alineación de las correas de
circuito de aceite hidráulico. severos daños por calentamiento al motor o al
2. Mantenga limpio todo el cortacésped para impedir
para limpiar el motor si está caliente. agua fría dañará el motor. Use aire comprimido No lave un motor caliente ni en operación. El
-IMPORTANTE-
componentes eléctricos. use chorro a alta presión ni dirija el chorro sobre
1. Lave todo el cortacésped después de cada uso. No
4.9 DESPUÉS DE LA OPERACIÓN
la llave.
6. Gire la llave de encendido a la posición OFF y quite
ADVERTENCIA:
baje lentamente la pendiente. llantas pierden tracción, desconecte las cuchillas y innecesarios y desplácese a baja velocidad. Si las ni se detenga repentinamente, evite giros
2. Para evitar volcarse o perder el control, no arranque
manual para mayores detalles. esta máquina. Vea la Sección 2.5, página 7 de este protección contra vuelco es un equipo estándar para tracción y el control de dirección. El sistema de césped está mojado. El césped mojado reduce la desplazarse en cuestas, especialmente cuando el corte. Sin embargo, debe tener cuidado al tracción y estabilidad bajo condiciones normales de
1. Este cortacésped se ha diseñado para tener buena
OPERACIONES APROB ADAS POR OSHA. 15 grados. SIEMPRE CUMPLA CON LAS máquina debe ser operada en cuestas mayores a extremo cuidado. Bajo ninguna circunstancia la se resbalen, reduzca la velocidad y opere con puede retroceder por la pendiente sin que las ruedas (con la plataforma de corte baja). Si la máquina si puede trabajar en una cuesta, trate de retroceder NO OPERE en pendientes empinadas. Para probar
5. Accione el freno de estacionamiento.
4.7 OPERACIÓN EN UNA CUESTA
Sección 4
Page 94
16
STT99CES SP
-NOTA-
DESCONECTAR
PRESIONE HACIA ABAJO PARA
TIRE HACIA ARRIBA PARA ACCIONAR
permita que el motor opere a sus máximas RPM. de carga, reduzca la velocidad hacia adelante y motor comienza a disminuir su velocidad por exceso mantener apropiadamente la velocidad de corte. Si el
4. Siempre opere el motor a máxima aceleración para
empuje el interruptor a la posición de desconexión.
3. Para desconectar la transmisión de la plataforma,
adquiere velocidad. Esto es normal. embrague eléctricos mientras el cortacésped Es causado por el engrane de los platos del desconectar la transmisión de la plataforma. Puede escucharse un chirrido al accionar o
Figura 4-3 Interruptor de accionamiento del cortador
-NOTA-
mueva hacia adelante. Cuanto más se permita al control reversa, permita que la palanca derecha de dirección se Para dirigirse a la derecha mientras se desplaza en
cortacésped a la izquierda. desplazarse hacia adelante, más rápido girará el mueva hacia adelante. Cuanto más se permita al control reversa, permita que la palanca izquierda de dirección se Para dirigirse a la izquierda mientras se desplaza en
ligeros ajustes con los controles de dirección. recta en reversa. Puede ser necesario hacer El cortacésped no puede desplazarse en línea
en reversa. Mantenga baja la velocidad de desplazamiento al viajar Para desplazarse en reversa, tire hacia atrás ambas asas.
propiedad. Pueden ocurrir lesiones personales o daños a la obstáculos. Despeje el área antes de retroceder. Antes de ir hacia atrás, vea que no haya personas u
PRECA UCIÓN:
PRECA UCIÓN:
instrumentos, (Figura 4-3) a la posición accionada. interruptor amarillo, ubicado en el panel de
2. Accione la transmisión de plataforma tirando del
transmisión de plataforma. velocidad moderada del motor al accionar la esto acorta la vida del embrague eléctrico — use una transmisión de la plataforma en alta velocidad ya que velocidad máxima. No trate de accionar la
1. Ponga el control de aceleración en cerca de 3/4 de la
PLATAFORMA (CUCHILLAS DE CORTE)
4.6 CONEXIÓN DE LA TRANSMISIÓN DE
estacionamiento. Si el cortacésped debe estacionarse, accione el freno de las palancas de dirección vuelvan a la posición neutral. Para detener el desplazamiento en reversa, permita que
cortacésped a la derecha. desplazarse hacia adelante, más rápido girará el
-IMPORTANTE-
-NOTA-
observar toda el área detrás del cortacésped. sea absolutamente necesario y sólo después de retroceder. No corte en reversa a menos que Desconecte la potencia al cortacésped antes de
Desplazamiento en reversa
levantar la plataforma de corte) sección 4.13 para instrucciones sobre cómo reborde en un ángulo de 45 grados. (Vea la plataforma y desplácese hacia atrás sobre el detendrá sobre el reborde. Levante la reborde de una acera. El cortacésped se No se desplace hacia adelante sobre el
velocidad de desplazamiento. controles de dirección, mantenga baja la cortacésped. Mientras aprende a operar los dirección producirá una operación suave del La operación suave de las palancas de
Section 4
Page 95
15
palancas, más rápido girará el cortacésped a la derecha. dirección hacia atrás. Cuanto más atrás se tiren las desplaza hacia adelante, tire la palanca derecha de Para dirigir el cortacésped a la derecha mientras se
palancas, más rápido girará el cortacésped a la izquierda. dirección hacia atrás. Cuanto más atrás se tiren las desplaza hacia adelante, tire la palanca izquierda de Para dirigir el cortacésped a la izquierda mientras se
posición neutral. palancas de control de dirección nuevamente a la Para detener el desplazamiento hacia adelante, tire de las
cortacésped.
6. Permita que el motor se entibie antes de operar el
el arrancador y acortar la vida de batería. arrancador. Los arranques prolongados pueden dañar cada intento de arranque para evitar sobrecalentar el segundos. Permita por lo menos 60 segundos entre la llave en la posición ST ART por más de 15 suéltela en cuanto arranque el motor. No mantenga
5. Gire la llave de encendido a la posición STAR T y
cerca de la mitad de la velocidad del motor.
4. Mueva el control de aceleración del motor hasta
3. Accione el freno de estacionamiento.
y para disminuirla, tire de las palancas hacia atrás. empuje las palancas de control de dirección más adelante mayor será la velocidad. Para aumentar la velocidad, similar. Cuanto más adelante se empujen las palancas, las palancas de dirección hacia adelante una distancia libere el freno de estacionamiento y empuje lentamente Para desplazarse hacia adelante con el cortacésped,
Desplazamiento hacia adelante
de proceder a cortar. que se sienta cómodo con los controles antes Practique la operación del cortacésped hasta
operación uniforme. controles de dirección para obtener una Aprenda a controlar con suavidad los
desplazándose lentamente hacia adelante. Comience practicando a baja velocidad y
-IMPORTANTE-
de operar en pendientes. Aprenda la operación en terreno plano antes la máquina antes de tratar de cortar. hasta que se sienta cómodo con el manejo de edificios, cercas, u obstrucciones. Practique en el terreno en un área abierta, lejos de las operaciones de conducción y velocidad transmisiones hidrostáticas, debe practicar una máquina con dirección de palanca y/o Si no está familiarizado con la operación de
-IMPORTANTE-
PRECA UCIÓN:
control de dirección en la posición neutral. cinturón de seguridad y coloque las palancas de
2. Siéntese en el asiento del operador, asegure el
completamente abierta. (Vea la sección 7.5.) ubicada detrás del asiento del operador, esté
1. Asegúrese de que la válvula de corte de combustible,
causar daños al motor y/o lesiones personales. condición de “embalamiento” del motor que puede puede ser potencialmente explosivo o causar una líquidos de arranque en el sistema de toma de aire NO USE LÍQUIDOS DE ARRANQUE. El uso de
4.4 ARRANQUE DEL MOTOR
es necesario. (Vea la sección 7.10.)
6. Revise la presión de las llantas. Corrija la presión si
(Vea la sección 4.2.)
5. Revise la correcta operación del sistema de bloqueo.
sea necesario.
4. Revise que no haya tornillería floja. Apriete según
(Vea la sección 7.3.)
3. V erifique el nivel de aceite en el tanque hidráulico.
(Vea la sección 7.4.) después de las primeras 20 horas de operación.
2. Cambie el aceite de motor y el filtro de aceite
y su desgaste a las 2, 4 y 8 horas.
1. Verifique la correcta alineación de todas las correas
DIRECCIÓN
4.5 DESPLAZAMIENTO EN EL TERRENO Y
aproximadamente 10 horas) INICIAL (Primer Día de uso o
4.3 PROCEDIMIENTOS DE ARRANQUE
Sección 4
Page 96
390S141-1 SP
14
daños a la propiedad. provocarle lesiones a usted o a terceros o causar puente ningún interruptor; el hacerlo puede defectuosamente. No desconecte ni ponga en bloqueo desconectado o funcionando Nunca opere el cortacésped con el sistema de
ADVERTENCIA:
estacionamiento no accionado. y/o las cuchillas de corte accionadas y/o el freno de control de dirección en una posición distinta de la neutral motor si el operador deja el asiento con las palancas de operador en el asiento. El sistema de bloqueo apaga el de control de dirección en la posición neutral y el el freno de estacionamiento esté accionado, las palancas que la transmisión de plataforma esté desconectada, que de seguridad que evita que el motor arranque a menos
El cortacésped está equipado con un sistema de bloqueo
SEGURIDAD
4.2 SISTEMA DE BLOQUEO DE
reparación. distribuidor autorizado de Scag para diagnóstico y el motor, la luz destellará un código. Consulte con su combustible Kohler (EFI). Si ocurre un problema con Indica la operación de la inyección eléctrica de
17 . Luz de comprobación de motor (Figura 4-1).
posición vertical y bloqueada. usarse solo cuando la barra contra vuelco esté en asegurar al operador. El cinturón de seguridad debe
16 . Cinturón de seguridad (Figura 4-1). Usado para
líquído solamente. máquinas cortacésped con motores enfriados por temperatura de operación del motor. Se usa en
15 . Indicador de temperatura (Figura 4-1). Indica la
desenganche de para soltar la plataforma de corte. pedal hacia adelante y levante la palanca de posición de transporte. Para corte normal, empuje el
Figura 4-2 Control de válvula de descarga
DESCARGA VÁLVULA DE CONTROL DE
4-1). Usada para trabar la plataforma de corte en la
14. Palanca de liberación de la plataforma (Figura
corte deseada. para poner la plataforma de corte en la altura de
13 . Ajuste de la altura de corte (Figura 4-1). Usado
plataforma de corte.
(Figura 4-1). Usada para levantar y bajar la
12 . Palanca de pie de elevación de plataforma
libremente). permite que el cortacésped se mueva a mano (rueda válvulas en el sentido contrario a las agujas del reloj, durante la operación del cortacésped. El giro de las estar en esta posición y apretadas a 10 pies/lb) mueva con potencia hidráulica. Las válvulas deben reloj hasta que se detengan permite que la unidad se giro de las válvulas en el sentido de las agujas del se usan para “rodar libremente” el cortacésped. El
(Figura 4-2). Ubicadas en las bombas hidráulicas,
11. Palancas de control de la válvula de descarga
cantidad de combustible en el tanque.
10 . Indicador de combustible (Figura 4-1). Indica la
desconectar los frenos de estacionamiento. frenos de estacionamiento. Presione la palanca para estacionamiento. Tire de la palanca para accionar los
1). Usado para accionar y desconectar los frenos de 9 . Control del freno de estacionamiento (Figura 4-
cortacésped al avanzar hacia adelante o en reversa. Usado para controlar la rueda derecha del
8. Control derecho de dirección (Figura 4-1).
cortacésped al avanzar hacia adelante o en reversa. Usado para controlar la rueda izquierda del
7 . Control izquierdo de dirección (Figura 4-1).
zócalo e instale uno nuevo. Para reemplazar los fusibles, retire el fusible del Amp protegen el sistema eléctrico del cortacésped.
6 . Portafusibles (Figura 4-1). Dos fusibles de 20
después. Reinicia automáticamente. establecida y continuará destellando hasta 2 horas empezará a destellar 2 horas antes de la hora sistema hidráulico. El mantenimiento programado mantenimiento del motor y los cambios de aceite del posición ON. Ha fijado los recordatorios para el interruptor de la llave de encendido está en la horas que ha operado el motor. Opera cuando el
5 . Horómetro (Figura 4-1). Indica el número de
Section 4
Page 97
13
Figura 4-1 Controles e Instrumentos de control horario
2008 STT-EFI CHMI
HORÓMETRO
VÁLVULA DE DESCARGA
VÁLVULA DE DESCARGA
MEDIDOR DE COMBUSTIBLE
482796
ENGINE LIGHT
CHECK
F
SLOW
CINTURÓN DE SEGURIDAD
LIBERACIÓN DE LA PLATAFORMA
DE CORTE AJUSTE DE ALTURA
DE DIRECCIÓN CONTROL DERECHO
FAST
ELEVACIÓN DE LA PLATAFORMA
FUSIBLES
MOTOR REVISAR LUZ DE
DEL MOTOR ACELERACIÓN CONTROL DE
DE DIRECCIÓN CONTROL IZQUIERDO
ESTACIONAMIENTO FRENO DE CONTROL DEL
DE ENCENDIDO INTERRUPTOR
AMPERÍMETRO
DEL CORTACÉSPED LA PLATAFORMA INTERRUPTOR DE
DE DIRECCIÓN CONTROL IZQUIERDO
servicio. descarga y la máquina debe ser llevada para darle negativo del medidor, esto indica una condición de positivo del medidor. Si la aguja está hacia el extremo funcionando, la aguja debe estar hacia el extremo
motor y tiene tres posiciones; OFF, ON, y START. interruptor de encendido se usa para arrancar el
1 . Interruptor de encendido (Figura 4-1). El
carga del sistema. Cuando el motor está
4 . Voltímetro (Figura 4-1). Indica la condición de
cortacésped.
estos controles para la operación segura y eficiente del de más adelante. MARCHA EN VACÍO. La posición de corte es la completamente hacia atrás es la posición de
importante conocer la ubicación, función y operación de
todos los controles del cortacésped y el motor. Es
Antes de operar el cortacésped, debe familiarizarse con atrás disminuye la velocidad del motor. La posición velocidad del motor. T irando de la palanca hacia Presionando la palanca hacia abajo aumenta la
IDENTIFICACIÓN
4.1 CONTROLES E INSTRUMENTOS
Usado para controlar la velocidad de motor.
3. Control de aceleración del motor (Figura 4-1).
la transmisión de plataforma. plataforma. Presione el interruptor para desconectar interruptor para accionar la transmisión de sistema de transmisión del cortacésped. Tire del
PRECA UCIÓN:
antes de operar este cortacésped. propósito de todos los controles e instrumentos haya leído este manual. Aprenda la ubicación y el No trate de operar este cortacésped a menos que
(Figura 4-1). Usado para accionar y desconectar el
2 . Interruptor de la plataforma del cortacésped
INSTRUCCIONES DE OPERACIÓN
Sección 4
Page 98
12
Acres por día: 23.7
Ancho de corte: 61"
La tabla es un estimado basado en un tiempo de corte de 8 horas por día, a 6 MPH (9 KPH), con una cuota para traslape y giros.
La tabla siguiente lo ayudará a determinar cuántos acres cortará su cortacésped Scag por día.
3.8 PRODUCTIVIDA D
Peso de operación aproximado 1400# Altura total 46 " Ancho total 72" Ancho de alineación 55" Longitud 87.5"
3.7 PESOS Y DIMENSIONES SMT61V
Depósito hidráulico.................................................................... Nylon; capacidad 3 cuartos
Filtro de aceite hidráulico ........................................................... Tipo roscado (spin-on) de 10 micras
3.6 SISTEMA HIDRÁULICO
Eje motriz ....................................................................................Eje de la horquilla de ajuste con dos uniones en U de alta velocidad
Tipo embrague eléctrico............................................................. Embrague eléctrico Ogura
SMT61........................................................................... Número de parte Scag - 481558
Correas de la plataforma de corte: ................................... Sección B, de Kevlar. Auto ajustado, auto apretado
Poleas del eje: ................................................................... Acero partido con cubos cónicos de fácil desmontaje
de grasa de grasa en la parte superior y cabezal móvil de alivio de exceso rodamiento de rodillos cónicos, bajo mantenimiento con conexión
Ejes: ..................................................................................Servicio pesado, 1-1/8" en la parte superior, cuerpo fundido,
locas: ....................................................................13x 5.00 cuatro capas (52"), 13 X 6.00 cuatro capas (61" & 72")
.............................................................Negra, polipropileno (plástico), flexible
Ruedas
Tolva de descarga
..........................................................................................cargada por resorte Tolva de descarga
de
descarga: ...................................................... Abertura de descarga extra ancha de 11.5" con tolva de descarga
Abertura
......................................................................................... plataforma de corte mediante un eje motriz.
......................................................................................... de panel de control conectado a la caja de cambios de la
las cuchillas: ....................................... Embrague eléctrico de accionamiento de cuchilla con interruptor
de
Accionamiento
..........................................................................................desgaste SMT 61V: Tres (3) cuchillas de corte de 21"
Cuchillas de corte:............................................................. Grosor 0.197, borde cepillado, material Marbain™ resistente al
1.00" a 6" en incrementos de 1/4"
Ajuste de altura de corte: .................................................. Ajuste con palanca de pie desde el asiento del operador, desde
61" (155.0 cm)
................................................................
Ancho de corte:
..........................................................................................calibre 7 (3/16"). Faldón de plataforma calibre 7 (3/16").
Construcción: .................................................................... Placa de soporte de acero calibre 10 reforzada con
Diseños delantero y de montaje frontal
Tipo: ..................................................................................Flotante, ajustable, anti raspado, de diseño híbrido que combina
Sección 3
3.4 PLA T AFORMA DE CORTE
Page 99
11
e.
-NOT A-
condiciones de cort desplazamiento hacia adelante debe ajustarse en función de las transporte. Para un mejor desempeño de corte, la velocidad de La máquina se desplazará a 12 MPH (19 KPH) para fines de
Reversa ................................................................................... 0-6 MPH (0-9 KPH)
Adelante.................................................................................. 0-12 MPH (0-19 KPH)
V elocidad de desplazamiento:
Asiento ...................................................................................... Acolchado, cojín grueso con apoyo de descanso alto
Motriz ...................................................................................... 12 PS I
Rueda libre delantera ............................................................... Llantas macizas
Presión de la llanta: indicador y tapa de combustible
Tanque de combustible.............................................................. Tanque de polietileno de 10 galones, sin costuras, con gran abertura e
(2) Motrices ............................................................................. 24 X 12.0 X 12 sin cámara neumática, de cuatro capas, borde radial
(2) Rueda libre en la parte delantera ........................................ 13 X 6.00, cuatro capas
Ruedas: ambas ruedas motrices
Freno de estacionamiento .......................................................... Mecanismo accionado por palanca conectado a los frenos en los ejes de
................................................................................................... dedos, con control individual de cada rueda con amortiguadores de gas
Control de dirección/desplazamiento ......................................... Control de dirección de doble palanca accionado con la punta de los
Motores de la rueda motriz............................................................... Dos motores Hydro-Gear™ 18E de hierro fundido de alto torque
................................................................................................... desplazamiento sin operación del motor y válvula de alivio de presión
Bombas hidrostáticas................................................................. Dos bombas Hydro-Gear™ BDP 16A con válvulas de descarga para el
................................................................................................... dos motores de hierro fundido y alto torque
Sistema de transmisión .............................................................. Transmisión hidráulica con dos bombas de desplazamiento variable y
3.3 TRACTOR
aceite Remoto
Inyección electrónica de combustible
Fusibles...................................................................................... Dos (2) de 20 Amp
Indicador de T emperatura
................................................................................................... manual Interruptor BBC Fusibles y Módulo de arranque de seguridad,
Tablero de instrumentos ............................................................ Amperímetro, Interruptor de encendido, Acelerador, Estrangulación
................................................................................................... de estacionamiento
Interruptores .............................................................................. Asiento, control de neutral, accionamiento de cortacésped (BBC), freno
Arrancador................................................................................. Eléctrico, 12 voltios, de corona, bloqueo operado por llave y solenoide
Polaridad del sistema ................................................................. Tierra negativa
Salida de carga ........................................................................... 12 V oltios, 20 Amperios, Kohler
Sistema de carga ........................................................................ Alternador
Batería ........................................................................................ 12 voltios
3.2 SISTEMA ELÉCTRICO
Correa de transmisión de la bomba (31EFI) .............................. Número de parte Scag - 483678
Correa de la transmisión de la plataforma................................. Número de parte Scag - 481460
Correas: ...................................................................................... Correa de Kevlar. Auto ajustado, auto apretado
Arrancador................................................................................. Arranque eléctrico con arrancador de solenoide
Conjunto de bomba de aceite............................................................Bomba de aceite de desplazamiento positivo Gerotor™ con filtro de
Combustible ............................................................................... Gasolina sin plomo con un octanaje mínimo de 87
Conjunto de bomba de combustible Kohler............................... Bomba eléctrica de combustible con filtro en línea
V elocidad en vacío ..................................................................... 1500 RPM, Kohler
Controlador ................................................................................Tipo mecánico con control de velocidad variable fijado en 3800 RPM
Cilindros ..................................................................................... 2 con camisas de hierro fundido
Desplazamiento ......................................................................... 31EFI Kohler de 747cc.
Tipo :........................................................................................... 4 ciclos, gasolina, dos cilindros, eje horizontal
Potencia ..................................................................................... 31HP a 3600 RPM (Modelo STT61V -31EFI-SS)
Modelo ...................................................................................... Kohler Aegis
Marca ......................................................................................... Kohler 31HP (Espec. #PS-LH775-xxxx)
Tipo general ............................................................................... Industrial de servicio pesado/Comercial de gasolina
3.1 MOT OR
Sección 3
Page 100
390S0150G
483398
10
482710
483300
483429
483397
483402
483402
483397
481568
REVERSA
R
483425
F
ADELANTE
LEA EL MANUAL DEL OPERADOR
ANTES DE OPERAR LA MÁQUINA
INSTALE LA CUBIERTA DE LA CORREA
483411
483406
483407
483407
Sección 2
ADVERTENCIA
2.7 CALCOMANÍAS INSTRUCTIVAS Y DE SEGURIDAD
Loading...