Sawstop Rt-phfs, Rt-fs User Manual
STANDALONE ROUTER TABLE
OWNER’S MANUAL
MODEL RT-FS/RT-PHFS
Copyright SawStop, LLC
All Rights Reserved
1st printing, January 2018
Updates of this manual may be
available at www.sawstop.com
The Standalone Router Table Assembly shown on the front cover is the cast iron model
RT-FS. The Four-Post Router Lift with Lock, Downdraft Dust Collection Box for Router Lift,
Flip Stop for Router Fence and Single Vertical Feather Board for Router Tables are installed.
These are optional accessories that does not come included with your
Standalone Router Table. Your setup may look different.
SawStop, the SawStop blade logo, and the conguration of this product are either registered
trademarks or trademarks of SawStop, LLC. Software copyright by
SawStop, LLC. All rights reserved.
TO OUR CUSTOMERS
Thank you for purchasing the SawStop Standalone Router Table Assembly with Phenolic or
Cast Iron Table. We are condent you will be pleased with the quality and performance.
This manual tells you more about your Standalone Router Table Assembly with Phenolic or
Cast Iron Table and how to operate and maintain it. Please read the manual carefully. The
manual also includes our warranty and important safety information.
If you ever have any questions or comments, feel free to contact us at the address below.
SawStop, LLC
11555 SW Myslony Street | Tualatin, Oregon 97062 USA
Phone: (503) 570-3200
Fax: (503) 570-3303
Email: info@sawstop.com
www.sawstop.com
HOW TO GET HELP
Missing Parts? Have Questions?
Our technical support team is standing by
M-F, 6:30am-5pm PST
to help with whatever you need.
Give us a call at
503.582.9934
Email us at
SERVICE@SAWSTOP.COM
TABLE OF CONTENTS
Product Specications.........................................................................
Parts Inventory.....................................................................................
Floor Stand (RT-STF)......................................................................................................
32" x 24" Cast Iron Router Table (RT-C32).....................................................................
32" x 24" Phenolic Router Table (RT-PH32)....................................................................
32" Fence Assembly (RT-F32).........................................................................................
Assembly Options................................................................................
Assembly and Installation.....................................................................
Assembling the Floor Stand ..........................................................................................
Assembling the Cast Iron Table......................................................................................
Installing the Cast Iron Table..........................................................................................
Assembling the Phenolic Table......................................................................................
Installing the Phenolic Table...........................................................................................
Assembling the Fence....................................................................................................
Reference............................................................................................
Warranty.........................................................................................................................
Safety.............................................................................................................................
Warnings........................................................................................................................
Exploded View 1: Floor Stand for Router Tables (RT-STF) ..............................................
Parts List 1: Floor Stand for Router Tables (RT-STF) .....................................................
Exploded View 2: 32" x 24" Cast Iron Router Table (RT-C32) ...........................................
Parts List 2: 32" x 24" Cast Iron Router Table (RT-C32) ...................................................
Exploded View 3: 32" x 24" Phenolic Router Table (RT-PH32) ........................................
Parts List 3: 32" x 24" Phenolic Router Table (RT-PH32) .................................................
Exploded View 4: 32" Fence Assembly for Router Tables (RT-F32) ...............................
Parts List 4: 32" Fence Assembly for Router Tables (RT-F32) .......................................
1
3
3
5
6
7
9
11
11
17
19
20
22
23
30
30
31
31
33
34
35
36
37
38
39
40
Available Accessories..........................................................................
41
PRODUCT SPECIFICATIONS
Floor Stand for Router Tables
Height Above Floor 34 ½" - 36 ½"
32" x 24" Cast Iron Router Table
Cast Iron Table 32" x 24"
Maximum Fence Travel 5 ½"
Front T-slot to Arbor Center 6 ½"
Width of Front T-slot
Rear T-slot to Arbor Center 5"
Width of Rear T-slot
½” at top,
3
⁄8" at bottom
1” at top,
¾" at bottom
32" x 24" Phenolic Router Table
Phenolic Table 32" x 24"
Maximum Fence Travel 30"
Front T-slot to Arbor Center 7"
Width of Front T-slot
Rear T-slot to Arbor Center 5 ¾"
Width of Rear T-slot
½” at top,
3
⁄8" at bottom
1” at top,
¾" at bottom
1
32" Fence Assembly for Router Tables
Length 35 ¾"
Height 3 ½"
Width 4"
RT-FS/RT-PHFS OWNER’S MANUAL
This page is blank.
RT-FS/RT-PHFS OWNER’S MANUAL
2
PAGES:
PARTS INVENTORY
3-8
Some products are shipped partially assembled. Please unpack the parts carefully and
conrm you have received each item on the lists below.
IF YOU CANNOT FIND AN ITEM ON THIS LIST, CHECK THE MOUNTING
LOCATIONS OR EXAMINE THE PACKAGING MATERIALS VERY CAREFULLY.
CERTAIN COMPONENTS MAY HAVE BEEN PRE-INSTALLED FOR SHIPPING
PURPOSES.
Floor Stand for Router Tables (RT-STF)
A.
Lower Front/Rear Bracket (2)
B.
Lower Side Bracket (2)
C.
Caster Mounting Bracket (1)
D.
Upper Front/Rear Bracket (2)
E.
Upper Side Bracket (2)
F.
Stand Leg (4)
G.
Floor Stand Switchbox Mounting
Bracket Assembly with Power Cord (1)
H.
M5 x 0.8 x 45 Pan Head
Phillips Screw (2)
I.
Caster Assembly with Table Bracket
Support Plate (1)
J.
M8 x 1.25 Lock Nut (2)
K.
M6 x 16 x 2 Washer (56)
L.
M6 x 1.0 x 16 Socket Head
Cap Screw (15)
N.
M10 x 1.5 Hex Nut (4)
O.
Wheel Housing (2)
P.
3" Wheel (2)
Q.
M8 x 1.25 x 50 Hex Head Bolt (2)
R.
M6 x 1.0 x 12 Socket Head
Cap Screw (5)
S.
M8 x 19 x 1.5 Washer (6)
T.
Handle Mounting Bracket (1)
U.
M6 Lock Washer (14)
V.
M6 x 1.0 x 12 Hex Head Bolt (36)
W.
M4 x 0.7 Hex Nut (4)
X.
M4 x 0.7 x 20 Pan Head
Phillips Screw (2)
Y.
M6 x 1.0 Hex Nut (1)
M.
Leveling Foot (4)
3
RT-FS/RT-PHFS OWNER’S MANUAL
A
B
C
D
E
I
F
L
M
N
O
G
H
T
U
V
W
X
Y
R
S
P
Q
J
K
You will also need the following tools to complete the Floor Stand Assembly:
• Phillips Head Screwdriver
• 14mm Wrench
• 8mm Wrench (x2)
• 5mm Hex Wrench
• 10mm Wrench
• Level
• 13mm Wrench (x2)
See Exploded View #1 on page 33 for more information.
RT-FS/RT-PHFS OWNER’S MANUAL
4
32" x 24" Cast Iron Router Table (RT-C32)
A.
32" x 24" Cast Iron Table (1)
B.
M6 x 1.0 Hex Nut (10)
C.
M6 x 1.0 x 40 Flat Head Phillips Screw (10)
B
C
A
You will also need the following tools to complete the Cast Iron Router Table assembly:
• Phillips Head Screwdriver
See Exploded View #2 on page 35 for more information.
5
RT-FS/RT-PHFS OWNER’S MANUAL
32" x 24" Phenolic Router Table (RT-PH32)
A.
32" x 24" Phenolic Router Table (1)
B.
M6 x 1.0 Hex Nut (10)
C.
M6 x 1.0 x 40 Flat Head Phillips Screw (10)
B
C
A
You will also need the following tools to complete the Phenolic Router Table assembly:
• Phillips Head Screwdriver
See Exploded View #3 on page 37 for more information.
RT-FS/RT-PHFS OWNER’S MANUAL
6
32" Fence Assembly for Router Tables (RT-F32)
A.
32" Router Table Fence (1)
B.
Fence Lock Knob (2)
C.
M8 x 23 x 2 Washer (2)
D.
23mm Wide Lock Knob Nut (2)
E.
Fence Face Plate Lock Knob (8)
F.
M6 x 16 x 2 Washer (14)
G.
M6 x 1.0 x 35 T-Bolt (8)
H.
2 ½" Dust Port (1)
I.
1/4"-20 x 3/4" Pan Head Phillips Screw (2)
J.
1/4"-20 Square Nut (8)
D
E
K.
Face Plate Space Bar (2)
L.
Router Fence Face Plate (2)
M.
Router Fence Guard (1)
N.
Router Fence Guard Spacer (2)
O.
32" Table Rail with Ruler and Lock Knob (2)
P.
Rail Mounting Bracket (2)
Q.
1/4" x 20 x 5/8" Hex Head Bolt (6)
R.
M6 x 1.0 x 12 Socket Head Cap Screw (8)
S.
19mm Wide Lock Knob Nut (2)
A
B
C
F
G
H
I
J
K
N
O
P
Q
R
S
You will also need the following tools to complete the 32" Fence Assembly:
L
M
• Phillips Head Screwdriver
• 5mm Hex Wrench
• 10mm Wrench
See Exploded View #4 on page 39 for more information.
7
RT-FS/RT-PHFS OWNER’S MANUAL
i
Throughout the manual, the exploded views are referenced to clarify the location and
name of each part. There are multiple exploded views in this manual, so a
decimal point system is used. The number before the decimal point refers to the
exploded view number (in this case, 1 through 4). The number after the decimal point
refers to the part number (as indicated by the number in the balloon in the exploded
view). For example, a part referenced as “1.1” would be the part labeled with a “1”
balloon in the exploded view #1.
• Exploded View #1: Floor Stand for Router Tables – See page 33
• Exploded View #2: 32" x 24" Cast Iron Router Table – See page 35
• Exploded View #3: 32" x 24" Phenolic Router Table – See page 37
• Exploded View #4: 32" Fence Assembly for Router Tables – See page 39
Important Part Identification Note:
RT-FS/RT-PHFS OWNER’S MANUAL
8
PAGES:
ASSEMBLY OPTIONS
9-10
Either the 32" x 24" Cast Iron Router Table or the 32" x 24" Phenolic Router Table can be
mounted to your Floor Stand for Router Tables.
The 32" Fence Assembly for Router Tables can be installed on either table.
32" x 24" Cast Iron Router Table
This huge cast iron table provides the
weight, stability and smoothness of cast
iron in a large, freestanding application.
Option 1 of 2
9
RT-FS/RT-PHFS OWNER’S MANUAL
32" x 24" Phenolic Router Table
This huge phenolic table provides the
lightweight precision of phenolic surfaces
in a large, freestanding application.
Option 2 of 2
RT-FS/RT-PHFS OWNER’S MANUAL
10
Loading...