WS2-r03-18-01-21TM
© 2021SATO Corporation. All rights reserved.
WS2 Series Printer
Technical Manual
WS208 / WS212
Revision History
Manual Version
Suggestion / Comment
Release Date
(Year / Month / Date)
WS2_Technical_Manual_ENG_02
P14. Changed the picture of BT module card onto the WS2
P13. Filled in the BT installation procedure and try to update
this manual before 3/22.
P13. Just wrote (Bluetooth option available depending on
region)
2019 / 03 /25
WS2_Technical_Manual_ENG_03
P15. Added a section of which the title is Peeler and Wireless
LAN Module
P32. Updated the main block diag. at section 5.1
P34. Updated the system diag. at section 5.2
P36. Updated the wiring diag. at section 5.3
2021 / 01 /07
P5. Added a prompt of installation of the peeler on the WLAN
card at section 1.2
P9. Added a prompt of installation of the peeler on the WLAN
card at section 1.3
2021 / 01 /15
i
Contents
Preface ........................................................................................................................................ 1
Who should read this manual ................................................................................................ 1
Related Documents ................................................................................................................ 1
1 Accessories Installation .......................................................................................................... 2
1.1 Cutter............................................................................................................................... 2
1.2 Peeler .............................................................................................................................. 5
1.3 Wireless LAN Module ...................................................................................................... 9
1.4 Bluetooth Module Card ................................................................................................. 12
1.5 Peeler and Wireless LAN Module .................................................................................. 15
2 Update Firmware .................................................................................................................. 22
2.1 Update Firmware via the USB Host ............................................................................... 22
2.2 Update Firmware in Atmel Mode ................................................................................. 23
3 Network ................................................................................................................................ 27
3.1 Network architecture .................................................................................................... 27
3.2 Ethernet Status Indicators ............................................................................................. 29
4 Troubleshooting ................................................................................................................... 30
4.1 Cutter and Peeler Issues ................................................................................................ 30
4.2 Internal Errors ............................................................................................................... 31
5 Technical Drawings ............................................................................................................... 32
5.1 Main Board Diagram ..................................................................................................... 32
5.2 System Diagram ............................................................................................................. 34
5.3 Wiring Diagram ............................................................................................................. 36
5.4 Exploded Drawing ......................................................................................................... 38
Appendix A: DIP Switch ......................................................................................................... 40
ii
Preface
This manual describes technical information about WS2 printers, including
installation guides, operating guides, printer setting tool help, network
architecture overview and technical drawings. It doesn’t contain programming
examples. For more information about printer programming, see related
documents.
Who should read this manual
This manual is intended for dealers, technicians and operators who need to install
and manage the hardware, firmware and network of WS2 printers.
Related Documents
￭ WS2 Series Operator Manual
1
1 Accessories Installation Cutter
1 Accessories Installation
This chapter describes how to install accessories on your printer.
1.1 Cutter
A cutter is used to cut the label after it is printed out. Full cutter cuts a label off
from a media roll.
To install a cutter:
Step 1. Remove the base frame
This part describes how to dismantle your printer.
1. Open the top cover and Remove tear bar.
2. Turn over your printer.
3. Loosen and remove 3 screws from the base.
4. Remove the base frame.
2
1 Accessories Installation Cutter
Step 2. Connect the cutter to the main board and Secure the cutter
to your printer
This part describes how to thread the cutter cable and connect to the main board.
1. Thread the cutter cable through 2 square holes as below.
2. Plug the cutter connector to J8 as below.
3. Remove interface cover and reinstall the base cover. Put the interface cover
back.
3
1 Accessories Installation Cutter
4. Secure it with 3 screws.
5. Turn over and lift top cover to secure cutter.
6. Align the 2 screw holes of the cutter on both sides of the platen roller.
7. Secure the cutter with 2 screws.
Step 3. Test the cutter
This part describes how to use the cutter to cut your label.
1. Place the media roll between the holders. Make sure the print side is up and
the media roll is clamped tightly by the holders.
2. Pull the media until it reaches out of your printer. Thread the media under the
media guides.
3. Thread the media into the slot of the cutter.
4. Close the top cover.
5. Send a print job or press the FEED button to test if the cutter works.
4
1 Accessories Installation Peeler
Shaft
E Ring
Peeler Bar
1.2 Peeler
A peeler automatically removes the liner from the printed label. The peeler sensor
detects if a peeled label is taken away.
To install a peeler:
In the case peeler and wireless LAN modules are used together, please refer to
section 1.5 of this manual for installation instructions.
Step 1. Remove the base frame
This part describes how to dismantle your printer.
1. Open the top cover and Remove tear bar.
2. Turn over your printer.
3. Loosen and remove 3 screws from the base.
4. Remove the base frame.
5
1 Accessories Installation Peeler
Step 2. Connect peeler to the main board then secure it
This part describes how to thread the peeler cable and plug to the mainboard.
1. Thread the peeler cable through two square holes as below.
2. Plug the peeler connector to J14 as below.
3. Put peeler in the printer and align two side of hole.
6
1 Accessories Installation Peeler
4. Insert shaft to two align hole from left to right.
5. Adjust shaft position to make sure notch exceed printer module.
6. Use sharp nose pliers to fix shaft with E Ring on both side.
7. Remove interface cover and reinstall the base cover. Put the interface cover
back.
8. Secure it with 3 screws.
9. Turn over your printer and open top cover.
10. Insert peeler bar to the gap between peeler module and roller.
7
1 Accessories Installation Peeler
Step 3. Test the peeler
This part describes how to use the peeler to peel the liner.
1. Open the peeler.
2. Place the media roll between the holders. Make sure the print side is up and
the media roll is clamped tightly by the holders.
3. Pull the media until it reaches out of your printer. Thread the media under the
media guides.
4. Remove 1-3 labels from the liner at the start of the media.
5. Thread the liner under the plate (beside the platen roller) and the peeler, until
the first label touches the platen roller.
6. Close the peeler and close the top cover.
7. Send a print job or press the FEED button to test if the peeler works.
8
1 Accessories Installation Wireless LAN Module
1.3 Wireless LAN Module
The Wireless LAN module provides Wireless LAN connectivity for your printer.
To install a Wireless LAN module:
In the case peeler and wireless LAN modules are used together, please refer to
section 1.5 of this manual for installation instructions.
Step 1. Remove the base frame
This part describes how to dismantle your printer.
1. Turn over your printer.
2. Loosen and remove 3 screws from the base.
3. Remove the base frame.
Step 2. Secure the Wireless LAN card and connect it to the main
board
This part describes how to thread the Wireless LAN card cable and connect it to
the main board.
1. Check the cable is connected on wireless module board.
2. Check the antenna is connected to port CN1.
9
1 Accessories Installation Wireless LAN Module
3. Locate the left side of printer. Find 2 screw holes above the top cover latch.
4. Thread the cable through the square hole.
5. Align the two holes and secure the card with 2 screws.
6. Plug the Wireless LAN cable 1 (red connector) to J14 as below.
10
Loading...