Introduction
1
Connect SATO Network Interface to the Network
5
ST-Print2003 Installation
8
Wireless Rev A
- This document describes the steps for installing and configuring
a SATO Network interface in a Windows environment. Refer to
the manual contained in the CD-ROM for more details.
- This Set Up Guide is for Windows users.
If you use SATO Network interface in UNIX/Linux, Netware or
Macintosh environments, please refer to the manual contained
in the CD-ROM.
Initial Installation & Configuration
2
For Administrators
1.Connect the SATO Network Interface into the printer
2.Connect the SATO Network interface to the network
3.Configure SATO Network interface
4.Install ST-Print2003 (Windows LPR printing only)
5.Setup the printer port
For Clients
1.Install ST-Print2003 (Windows LPR printing only)
2.Setup the printer port
3
Package Contents
You can configure the SATO Network Interface using either a wired or wireless connection.
<<Configuration with a wired connection>>
1. Ensure that the printer’s power is turned off (failure to do so may
result in damage to the Network interface card) and insert an
Ethernet cable into the Network interface card.
2. Plug the other end of the network cable into your network
connection.
. Turn the printer on.
3
Starting User Software
6
* Referrence Network Environment:
a) DHCP server environment
b) The printer driver is already installed in the PC.
* Explains how to configure SATO Network interface using Quick Setup.
* For advanced configuration or to change the configuration, refer to "Chapter 8" of the Users Manual.
* The screen displayed may vary depending on the Windows environment
<<Configuration with a wireless connection>>
1. Please configure a PC with WLAN capabilities to the following
wireless settings to be able to connect to the SATO Wireless
Interface.
SSID : Anything (not specified)
Channel : 11
WEP : none
Wireless Mode : Ad hoc
The ST-Print2003 installation allows printing with LPR. if you
want to print using a different method, please refer to the
SATO network interface manual.
1. From the main CD menu, select IP Port Drivers.
2. Select the language, and press Next.
3. The ST-Print2003 installer starts. Press Next.
4. The Software License Agreement will appear.
Press Yes if you accept the contents.
5. The Select the folder for copy destination will appear.
Click Next.
6. The Available Program Folder will appear. Press Next.
10. Select Print with LPR, then press Next.
11. Press Searching Print Server, then select the appropriate
SATO Network interface and press Next.
12. Assign the Printer Port Name. Press Next.
13. Press Finish and the port addition is complete.
Please verify that the followings are contained in the package.
- SATO EWA
- Setup Guide
- CD-ROM User Software
(Including configuration utility and Users Manual)
- Mounting Hardware
Connect Network Interface to the Printer
4
1. Turn off the printer power unplug the power cable.
2. Remove the 2 screws securing the existing port to the
back of the printer
3. Remove the existing port by pulling slowly outward.
4. Slide in the SA
the port with the 2 thunbscrews attached to the port.
5. Print a self-test page:
a. With the printer
wireless interface to the on postion.
b. Power printer on.
c. The printer should now print.
6. If successful, power the printer of
the down position. You are now ready to go to Step 5.
If unsuccessful reset the Network interface by turning the
printer of
go back to step 2.
7. If still unsuccessful contact SA
or by e-mail at: techsupport@satoamerica.com
.
TO Network Interface and secure
’s power off, turn DSW3 on the
f and return DSW3 to
f and then turning on DSW2 on the adapter, then
TO support at 704-644-1660
1. Please insert the CD-ROM User Software into the CD-ROM drive of your Windows PC.
* If the "Main menu" screen does not appear automatically
2. Press Quickset Utility.
7
Quick Setup
1. Select the language, and press Next.
2. Quick Setup starts. Press Next.2. Quick Setup starts.
, execute "run.exe" in the CD-ROM drive.
6. Configure the SATO Network interface wireless LAN settings to
match your wireless LAN environment. Verify your wireless LAN
settings and press Next.
3. The Software License Agreement will appear.
Click Yes if you accept the contents.
4. Select the SATO Network interface you want to configure, then
click Next.
7. Verify the configuration parameters, then press Execute.
5. To assign an IP address to the SATO Network interface
automatically, select Get IP Address Automatically, then press
Next.
* If you want to assign an IP address manually, select Assign IP
Address, then type in the appropriate IP address.
8. Configuration is complete. Press Finish.
7. Press Start and the ST-Print2003 installation will begin.
14. Select the printer that uses the newly added port. Press Next.
8. Select Yes, then press Finish.
15. The Port configuration is complete. Press Finish.
9. The Add ST-Print2003 appears. Press Next.
9
User Registration
- Please complete the User Registration via our web page after completing the SATO Network interface setup. User Regaistration
is used by SATO to improve product support and services. © 2009 Sato America, Inc. All rights reserved. P/N: 9001207(A)
- For any technical questions,
Loading...