INSTRUCTION MANUAL
Colour Video Monitor
VMC-8415FP
CONTENTS
PRECAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
PARTS NAMES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
CONNECTION . . . . . . . . . . . . . . . . . . . . . Back cover
SPECIFICATIONS . . . . . . . . . . . . . . . . . . Back cover
FEATURES
Equipped with video and audio input terminals
Equipped with Y/C input (S-VIDEO input)
terminal
This terminal is used to input Y/C separation
signals (S-VIDEO signals).
Horizontal resolution more than 800 TV lines
Built-in speaker
Multi voltage (100 – 240 V)
ACCESSORY
AC power cord (re-attachable)
Important (U. K. only)
Connect the mains lead to a suitable plug
following the colour code:
Blue wire (Neutral) → to plug pin N or
•
coloured black
Brown wire (Live) → to plug pin L or
•
coloured red
Green and Yellow wire (Earth) → to plug pin
•
E or “ %”
Do not connect Blue and Brown wire onto plug pin
E or onto earth symbol “%”.
About this manual
Before installing and using this unit, please read this
manual carefully. Be sure to keep it handy for later
reference.
PRECAUTION
WARNING:
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR OTHER MOISTURE.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
If the power supply cord (AC power cord) of this
appliance is damaged, it must be replaced. Return to a
SANYO Authorised Service Centre for replacement of
the cord.
If an abnormality does occur, turn the power switch off and
unplug the unit. Have a qualified technician perform any
repairs.
Do not use the monitor if it makes a strange noise, emits a
strange odor, or if smoke comes out from it
If used under these conditions, the monitor may cause a fire or
electric shock. Immediately unplug it and wait to make sure no
more smoke comes from it. Then take it to the dealer for service.
Do not try to repair or open the monitor yourself.
Do not allow the power cord to get damaged
Do not place heavy objects on the power cord.
•
Do not place the power cord near a heat source.
•
Do not excessively bend the power cord, modify it, or secure
•
it with staples.
Doing so may damage the power cord and cause a fire or
electric shock.
If the power cord is damaged, take it to the dealer and have it
replaced.
Do not allow dust or dirt to build up on the
power cord or power outlet
A build-up of dust may cause a short circuit or generate heat
and cause a fire.
Be especially careful when using the monitor in areas of high
humidity, in areas with frequent condensation, in kitchens, and in
places where there is excessive dust.
Periodically unplug the power cord and clean away the dust that
builds up between the plug terminals.
Cautions when plugging in the power cord
Make sure you insert the plug of the power cord all the way in
•
the power outlet. Using the monitor with the power cord not
fully plugged in may cause heat to generate and cause a fire.
Do not use the monitor with the power cord wound or tied up.
•
Heat may generate and cause a fire.
When using an extension cord, be sure that the total current load
•
of all equipment connected to it does not exceed the specified
ratings of the extension cord. If the rating are exceeded, heat may
generate and cause a fire. Make sure to carefully read the
specifications accompanying the extension cord.
Do not modify or open the cabinet
Never touch the inside of the monitor. High voltage circuits are
inside, and there is a high risk of fire or electric shock if they are
touched. Any internal checks, settings, or repairs should be
performed by the dealer.
Do not place object containing liquids (flower
vase, etc.) on top of the monitor.
If water or any other liquid does get inside the monitor,
immediately turn it off and unplug it.
Do not get the monitor wet
Do not allow the monitor to get wet or allow water or other
•
liquids inside it. Doing so may cause a fire or electric shock.
Be especially careful during rainy weather, snowy weather,
near the beach, or near bodies of water.
Do not use the monitor in a bathroom.
•
Do not use the monitor during a lightning
Do not touch it or its power cord during a lightning. Doing so
may cause an electric shock.
Do not place the monitor on an unstable surface
It may fall, causing damage or personal injury. If it falls and its
body is damage, immediately turn it off and unplug.
Never pull on the cord to unplug the power cord
Always unplug the power cord by holding the power plug and
•
slowly pulling out.
Pulling at the cord may damage the power cord and cause a
fire or electric shock.
Do not touch the power cord or plug with wet hands. Doing so
•
may cause an electric shock.
Cautions regarding the location where the
monitor is used.
Do not place it in locations with excessive humidity or dust, or
•
location subjected to oily vapors or steam.
Do not place it in locations subject to direct sunlight or near
•
heat generating equipment. Doing so may cause an accident
property damage.
Do not cover the air vents
Do not place the monitor in a poorly ventilated location. Do not
block its air vents by covering it with a cloth, placing it on a
carpet or blanket, or other means. If the air vents are blocked,
the internal temperature will rise and it may cause a fire.
Cleaning
Dirt can be removed from the cabinet by wiping it with a soft
•
cloth. To remove stains, wipe with a soft cloth moistened with
a soft detergent solution and wrung dry, then wipe dry with
dry soft cloth.
Do not use benzine, thinner or other chemical product on the
•
cabinet, as that may cause deformation and paint peeling.
Before using a chemical cloth, make sure to read all
accompanying instructions. Make sure that no plastic or
rubber material comes in contact with the cabinet for a long
period of time, as that may cause damage or paint peeling.
SERVICE
This unit is a precision instruments and if treated with care, will
provide years of satisfactory performance. However, in the event
of a problem, the owner is advised not to attempt to make
repairs or open the cabinet. Servicing should always be referred
to your dealer or Sanyo Authorized Service Centre.
Do not place object inside the monitor
Do not insert any metallic object through the ventilation grills.
•
Do not stick metal objects (paper clips, hair pins, etc.), paper,
•
matches, etc., inside the monitor.
1
PARTS NAMES
Front Panel
1
Rear Panel
1
SPEAKER
2
VOLUME control («)
For adjustment of audio volume.
3
CONTRAST control (»)
For adjustment of picture contrast.
4
POWER
COLOURBRIGHTCONTRASTVOLUME
7
BRIGHT control (ã)
For adjustment of picture brightness.
5
COLOUR control (õ)
For adjustment of colour enhancement.
POWER
6
COLOURBRIGHTCONTRASTVOLUME
Power button (Ñ POWER)
Press this button to turn the power on and off.
7
Power indicator
62 3 4 5
Lights when the power is on.
1
AC INPUT socket
Connect the AC power cord (supplied) securely to this
socket and to a wall outlet.
AC INPUT
VIDEO
Y/C
AUDIO
VIDEO
Y/C
OUT
OUT
OUT
IN
IN
IN
AC INPUT
1 23 764 5
VIDEO
VIDEO
Y/C
AUDIO
Y/C
OUT
OUT
IN
OUT
IN
IN
8
Y/C (4-pin mini-DIN) terminal specification
4
2
4
2
OUT
IN
3
1
3
1
Pin No. Signal
1 GND (Y)
2 GND (C)
3 Y
4 C
2
VIDEO OUT terminal (BNC-type)
Loop-throgh of the video in terminal.
Connect to the video input terminal for VCR or another
monitor.
3
VIDEO IN terminal (BNC-type)
Connect to the video output terminal of video
equipment, such as a VCR or a colour video camera.
4
AUDIO OUT terminal (RCA jack)
Loop-throgh output of the audio in terminal.
Connect to the audio input terminal of a VCR or
another monitor.
5
AUDIO IN terminal (RCA jack)
Connect to the audio output terminal of a VCR or other
equipment.
6
Y/C IN terminal (4-pin mini-DIN)
Connect to the Y/C separate output terminal of a video
camera, VCR or other video equipment.
7
Y/C OUT terminal (4-pin mini-DIN)
Loop-through output of Y/C in terminal. Connect to the
Y/C separate input terminal of a VCR or another
monitor.
8
Y/C or VIDEO signal input/output switch
Select the input/output signal either VIDEO (BNC) or
Y/C (4-pin mini-DIN jack).
2
CONNECTION
SPECIFICATIONS
Before making any connection, make sure all the devices are
turned off.
Before making the connections, please refer to the instruction
manual accompanying each device. If the devices are not
connected properly, that may cause a fire and/or damages.
Basic connections
To VIDEO
input terminal
VIDEO
OUT
From VIDEO
output terminal
Video camera
Monitor
IN
Monitor
AUDIO
OUT
IN
Video recorder
To AUDIO
input terminal
Y/C
OUT
IN
From AUDIO
output terminal
Video recorder
Connections to the Y/C terminals
Type Colour video monitor
Picture tube 15" 90° colour
Colour system PAL
Resolution 800 TV lines
Normal scan 6 % over scan of picture tube
effective screen area
Input terminals
Output terminals
Video in BNC connector (x1), 1.0 V
•
(p-p) composite video signal, 75 Ω
Audio in RCA jack (x1), 400 mVrms
•
Y/C-separated: 1 line, mini-DIN
•
4-pin connector (x1)
Y: 1.0 V (p-p), 75 Ω/C: 0.3 V (p-p), 75 Ω
Video out BNC connector (x1),
•
loop-through, automatic
termination setting
Y/C-separated OUT, mini-DIN
•
4-pin connector (x1), loop-through,
automatic termination setting
Audio out RCA jack (x1),
•
loop-through
Audio power output 1 W
Built-in speaker x1, impedance of 8 Ω
Power source AC 100 to 240 V 50/60 Hz
Power consumption 95 W
Operation temperature –10°C to 50°C (14°F to 122°F)
Storage temperature –20°C to 65°C (–4°F to 149°F)
Relative humidity 15 % to 90 %
Dimensions (W x H x D) 368 x 361 x 376 mm
Weight 15 kg
Accessary AC power cord x1
Diagrams are shown for explanatory purposes only, and have
•
been exaggerated, abbreviated or created as required, and
so may differ from the actual product.
Features and specifications are subject to change without
•
prior notice or obligations.
Monitor
To Y/C
input terminal
VIDEO
OUT
IN
From Y/C output terminal
Video camera
Monitor
AUDIO
OUT
IN
Video recorder
Y/C
OUT
IN
Video recorder
Note: The components and connection cables are not
included and must be purchased separately.
Printed on recycled paper
Dimensions
W
D
H
SANYO Electric Co., Ltd.
1AC6P1P2719-L8MAF/XE, UK, AU (0603KP-TVS)
312-0202-101 Printed in Taiwan
Loading...