Sanyo VMC-8214P Instruction Manual

Download

INSTRUCTION MANUAL

Color Video Monitor

Contents

Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Names of parts . . . . . . . . . . . . . . . . . . . . . . . . 3

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Basic operation. . . . . . . . . . . . . . . . . . . . . . . . 5

Adjust the OSD menu item. . . . . . . . . . . . . . . 6

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 7

Specifications . . . . . . . . . . . . . . . . . . . . . . . . 8

Language screen table. . . . . . . . . . . . . . . . . 10

Features

Equipped with Y/C input (S-VIDEO input) terminal

Eight languages OSD MENU

ENGLISH, FRANCAIS, DEUTSCH, ESPANOL, ITALIANO, RUSSIAN, CHINESE, JAPANESE

Horizontal resolution

More than 400 TV lines

PAL/NTSC colour system, selected automatically

Built-in speaker

About this manual

Before installing and using this unit, please read this manual carefully. Be sure to keep it handy for later reference.

Precautions

WARNING: TO REDUCE THE RISK OF FIRE

OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR OTHER MOISTURE. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. If the AC power cord of this appliance is damaged, it must be replaced. Return to a SANYO Authorised Service Centre for replacement of the cord.

If an abnormality does occur, turn the power switch off and unplug the unit. Have a qualified technician perform any repairs.

Do not use the monitor if it makes a strange noise, emits a strange odor, or if smoke comes out from it

If used under these conditions, the monitor may cause a fire or electric shock. Immediately unplug it and wait to make sure no more smoke comes from it. Then take it to the dealer for service. Do not try to repair or open the monitor yourself.

Do not allow the power cord to get damaged

Do not place heavy objects on the power cord. Do not place the power cord near a heat

source. Do not excessively bend the power cord,

modify it, or secure it with staples.

Doing so may damage the power cord and cause a fire or electric shock. If the power cord is damaged, take it to the dealer and have it replaced.

Do not allow dust or dirt to build up on the power cord or power outlet

A build-up of dust may cause a short circuit or generate heat and cause a fire. Be especially careful when using the monitor in areas of high humidity, in areas with frequent condensation, in kitchens, and in places where there is excessive dust. Periodically unplug the power cord and clean away the dust that builds up between the plug terminals.

Cautions when plugging in the power cord

Make sure you insert the plug of the power cord all the way in the power outlet. Using the monitor with the power cord not fully plugged in may cause heat to generate and cause a fire.

Do not use the monitor with the power cord wound or tied up. Heat may generate and cause a fire.

When using an extension cord, be sure that the total current load of all equipment connected to it dose not exceed the specified ratings of the extension cord. If the rating are exceeded, heat may generate and cause a fire. Make sure to carefully read the specifications accompanying the extension cord.

Do not modify or open the cabinet

Never touch the inside of the monitor. High voltage circuits are inside, and there is a high risk of fire or electric shock if they are touched. Any internal checks, settings, or repairs should be performed by the dealer.

Do not place object inside the monitor

Do not insert any metallic object through the ventilation grills.

Do not stick metal objects (paper clips, hair pins, etc.), paper, matches, etc., inside the monitor.

Do not place object containing liquids (flower vase, etc.) on top of the monitor.

If water or any other liquid does get inside the monitor, immediately turn it off and unplug it.

Do not get the monitor wet

Do not allow the monitor to get wet or allow water or other liquids inside it. Doing so may cause a fire or electric shock. Be especially careful during rainy weather, snowy weather, near the beach, or near bodies of water.

Do not use the monitor in a bathroom.

Do not use the monitor during a lightning

Do not touch it or its power cord during a lightning. Doing so may cause an electric shock.

Do not place the monitor on an unstable surface

It may fall, causing damage or personal injury. If it falls and its body is damage, immediately turn it off and unplug.

Never pull on the cord to unplug the power cord

Always unplug the power cord by holding the power plug and slowly pulling out. Pulling at the cord may damage the power cord and cause a fire or electric shock.

English

Precautions

Do not touch the power cord or plug with wet hands. Doing so may cause an electric shock.

Cautions regarding the location where the monitor is used.

Do not place it in locations with excessive humidity or dust, or location subjected to oily vapors or steam.

Do not place it in locations subject to direct sunlight or near heat generating equipment. Doing so may cause an accident property damage.

Do not cover the air vents

Do not place the monitor in a poorly ventilated location. Do not block its air vents by covering it with a cloth, placing it on a carpet or blanket, or other means. If the air vents are blocked, the internal temperature will rise and it may cause a fire.

Cleaning

Dirt can be removed from the cabinet by wiping it with a soft cloth. To remove stains, wipe with a soft cloth moistened with a soft detergent solution and wrung dry, then wipe dry with dry soft cloth.

Do not use benzine, thinner or other chemical product on the cabinet, as that may cause deformation and paint peeling. Before using a chemical cloth, make sure to read all accompanying instructions. Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time, as that may cause damage or paint peeling.

Please note:

Your SANYO product is designed and manufactured with high quality materials and components which can be recycled and reused. This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste. Please dispose of this equipment at your local community waste collection/recycling centre. In the European Union there are separate collection systems for used electrical and electronic products. Please help us to conserve the environment we live in!

This symbol mark and recycle system are applied only to EU countries and not applied to the countries in the other area of the world.

SERVICE

This unit is a precision instruments and if treated with care, will provide years of satisfactory performance. However, in the event of a problem, the owner is advised not to attempt to make repairs or open the cabinet. Servicing should always be referred to your dealer or Sanyo Authorized Service Centre.

English

Names of parts

Front Panel

Speaker AC INPUT socket

① ①

The speaker lets you hear the sound from the Connect the AC power cord (supplied) securely unit which is Connected to the audio input to this socket and to a wall outlet. terminals at the rear of the monitor.

On-screen display button (OSD)

②

When this button is pressed, the menu screen appears on the monitor screen. Press the OSD button once more,or

Select "EXIT OSD" and then press the ENTER button.

Cursor ( ) button ( )

③

When this button is pressed, the cursor moves down. When it reaches the bottom, it reappears at the bottom. In addition, this button is used to make adjustment values smaller.

Cursor ( ) button ( )

④

When this button is pressed, the cursor moves up. When it reaches the top, it reappears at the bottom. In addition, this button is used to make adjustment values larger.

Display selector button (ENTER)

⑤

If this button is pressed while the menu is on the monitor screen,the screen changes to the adjustment screen. If the button is pressed once more, the picture returns to the previous screen.

Power indicator

⑥

Lights when the power is on.

Power button ( POWER)

⑦

Press this button to turn the power on and off.

Rear Panel

AUDIO/VIDEO terminals:

②

When the signal I/P switch is turned to video Side,the audio and video signals from the unit which is connected to these terminals can be

monitored.

AUDIO/ Y/C terminals:

③

When the signal I/P switch is turned to Y/C side,the audio and s-video signals from the unit Which is connected to these terminals can be

monitored.

SIGNAL I/P switch

④

Select the input signal either video (BNC) or Y/C (DIN jack) by the switch.

Pin No. Signal

English 3

Connections

Before making any connection, make sure all the devices are turned off. Please refer to the instruction manual accompanying each device. If the devices are not connected properly, that may cause a fire and/or damages.

■Basic connections

Monitor

To Audio input terminal

To Video input terminal

To VIDEO input terminal

Recorder

To AUDIO input terminal

■Connections to the S-Video

terminals

To Audio input terminal

To AUDIO input terminal

Monitor

To S-Video input terminal

To Y/C input terminal

Recorder

(Rear panel)

: IN signal : OUT signal

Video camera

The components and connection cables are not included and must be purchased separately.

English

Monitor

Recorder

Video camera

Monitor

Recorder

Basic operation

Press the POWER button to turn on the

power. ON: The power is turned on (the POWER

indicator is lit). The signals from the channel (VIDEO or Y/C) which was being used when the power was last turned off will be input.

OFF: The power is turned off (the POWER

indicator is off).

Select the audio and video input.

Select the input signal either video (BNC) or Y/C (DIN jack)

from the rear panel by switch.

Menu screen operations

Press the OSD button.

The menu screen will be displayed. The menu screen will only be displayed for about 13 seconds.

Press the cursor ( ) or ( ) button.

The cursor will move up or down, so that you can select the desired menu item.

Select the desired menu item and then press the ENTER button.

If you press the ENTER button repeatedly while the menu screen is being displayed, the display will alternately change between the menu screen and the setting screen. At this time, the menu item will still be selected.

OSD ENTER

ENTER ENTER

Normal picture

During this operation, “8. VERSION” will be skipped and the screen will go straight to “EXIT OSD”.

English

Adjust the OSD menu item

Open the menu screen (press the OSD button), use the cursor ( / ) buttons to select the desired menu item, and then press the ENTER button.

OSD

ENTER

The setting characters which are displayed on each adjustment screen (such as 50%) may not display correctly (dropout) in some cases.

■COLOR adjustment

Select “1. COLOR 50%” and then press the ENTER button.

Use the cursor ( ) and ( ) buttons to adjust the color of the picture.

■TINT adjustment

Select “2. TINT 53%” and then press the ENTER button.

Use the cursor ( ) and ( ) buttons to adjust the tint of the picture (NTSC only).

■CONTRAST adjustment

Select “4. CONTRAST 75%” and then press the ENTER button.

Use the cursor ( ) and ( ) buttons to adjust the contrast of the picture.

■SHARPNESS adjustment

Select “5. SHARPNESS 50%” and then press the ENTER button.

Use the cursor ( ) and ( ) buttons to adjust the sharpness of the picture.

■VOLUME adjustment

Select “6. VOLUME 50%” and then press the ENTER button.

Use the cursor ( ) and ( ) buttons to adjust the sound volume.

■Menu screen language setting

Select “7. LANGUAGE” and then press the ENTER button.

Use the cursor ( ) and ( ) buttons to select the display language.

Only the menu screen and setting screen languages will be changed.

■BRIGHTNESS adjustment

Select “3. BRIGHTNESS 75%” and then press the ENTER button.

Use the cursor ( ) and ( ) buttons to adjust the brightness of the picture.

English

roubleshooting

Solutions to common problems related to your monitor are describe here. If none of the solutions presented here solve the problem, unplug the monitor and consult a SANYO-authorized dealer or service center for assistance.

Problem

No picture with the power on

No sound.

Shaking picture

No color, color is incorrect or picture is too dark

Uneven or mismatched color in parts of the picture

Points to be checked

Is the video signal being output from the connected component?

Is the input signal selected properly?

Is the audio signal being output from the connected component?

Is the volume set to the minimum level?

Is the audio cable disconnected?

Is the monitor close to a device which is generating a strong magnetic field?

Have the picture control settings (CONTRAST, BRIGHTNESS, TINT) been changed?

Are there any speakers or magnets nearby, or were they brought close to the monitor?

Measures (Remedy)

Set the connected component correctly.

Select the required video signal input with the monitor selector buttons. (VIDEO and Y/C)

Set the connected component correctly.

Adjust the volume using the VOLUME setting screen.

Securely connect the audio cable.

Move the device away from the monitor until the picture stabilizes.

Adjust the settings using the adjustment screens.

Move the speaker or magnet away from the monitor, and then turn the power off and wait at least 30 minutes before turning the power back on again.

Page

English

Specifications

Type

Color system

Rosolution

Input terminal

S-Video signal (Y/C in)

Video signal (BNC in)

Audio signal (AUDIO in)

Output terminal

S-Video signal (Y/C out)

Video signal (BNC out)

Audio signal (AUDIO out)

Audio output

Menu language

Picture adjustment

Sound adjustment

Normal scan

Speaker

Power supply voltage

Operating condition

Storage condition

Power consumption

Weight

Separate Y/C signal, mini-DIN connector

Y signal: 1.0 Vp-p, 75 Ωnegative sync C singal: 0.286 Vp-p, 75 Ω negative sync, bridge connection possible

Composite sync signal, 1.0 Vp-p, 75 Ω BNC connector (1)

6 dBs (400 m Vrms), RCA pin (1), bridge connection possible

Separate Y/C signal, mini-DIN connector

Y signal: 1.0 Vp-p, 75 Ωnegative sync C singal: 0.286 Vp-p, 75 Ω negative sync, bridge connection possible

Composite sync signal, 1.0 Vp-p, 75 ΩBNC connector (1)

6 dBs (400 m Vrms), RCA pin (1), bridge connection possible

Einglish/Frencais/Deutsch/Espanol/Italiano/Russian/Chinese/Japanese

COLOR/TINT(NTSC only)/BRIGHTNESS/CONTRAST/SHARPNESS

Adjustable speaker volume

6 % over scan of picture tube effective screen area

X1, impedance of 8 Ω

AC 100-240 V, 50/60 Hz

Temperrature: -10 - +50˚C ˚C Humidity: 10%-90% (non-condensation)

Temperrature: -20 - +65˚C ˚C Humidity: 10%-90% (non-condensation)

VMC-8214P

Color video monitor

NTSC, PAL

More than 400 TV lines

65W

14 kg

Diagrams are shown for explanatory purposes only, and have been exaggerated, abbreviated or created as required, and so may differ from the actual product.

Features and specifications are subject to change without prior notice or obligations.

■Accessories

AC power cord (Re-attachable)

English