High-resolution Camera
(minimum illumination of 0.05 Lux)
1/3" Colour CCD
1/3" Colour CCD
High-resolution Camera
High-resolution Camera
Built in DSP (digital signal processing) circuit
Built in DSP (digital signal processing) circuit
Intelligent digital motion detector
Intelligent digital motion detector
x32 Electronic sensitivity
x32 Electronic sensitivity
x8 Digital zoom with digital pan and tilt
x8 Digital zoom with digital pan and tilt
480 TV lines of horizontal resolution
480 TV lines of horizontal resolution
SSP compatible
SSP compatible
Dual power operation, 24 V AC / 12 V DC
Dual power operation, 24 V AC / 12 V DC
(minimum illumination of 0.05 Lux)
(minimum illumination of 0.05 Lux)
VCC-6975P
ISO 9001 REGISTERED FIRM
DNA Certification B. V., THE NETHERLANDS
Colour
PAL
Accredited
by the RvA
TV LinesHorizontal
SF-1407MV
1/3" Colour CCD
High-resolution Camera
VCC-6975P
Shown with optional lens
An all-new Intelligent Digital Motion Detector is built-in to detect moving objects in the picture and send an alarm
The intelligent Digital Motion Detector analyzes changes in picture brightness on the screen and uses the direction of motion and size
of the object to identify moving objects. The system can be set to produce an external alarm signal and/or switch to a x2 digital zoomin display. Furthermore, the center of the zoom-in picture stays focussed on the moving object.
x2 zoom x2 zoom
CAMERA 1 CAMERA 1
Display of monitor
Intelligent digital motion detector uses size of
object and direction of motion to identify moving objects.
Detection of a moving object prompts the
camera to zoom in on the object (x2), and
blinking camera ID is displayed on the monitor. An external alarm signal is also sent.
Display of monitor
Display of monitor
During the zoom-in display, the center of the picture travels and stays focussed on the object.
Duration of the zoom-in display is adjustable to
5, 10, 20, 30, and 60 seconds.
Reliable detection of moving objects
The intelligent Digital Motion Detector uses seven factors in analyzing changes in picture brightness to enable reliable motion detection and reduce false alarms.
1
Direction
It is possible to narrow the target to objects moving in certain
directions only. This feature enables the system to detect people
coming into a room while disregarding people going out. It is also
possible to detect all moving objects without setting the direction.
CAMERA 1 DIRECTION
Set the direction to “right”
2
Size
Freely set the size of target objects.
3
Masking
Freely establish the area where motion detection is turned off.
An area where motion
detection is turned off
4
Magnitude of movement
Set the magnitude of movement to be detected.
5
Brightness
Set the lowest level of brightness to be analyzed. Use this feature
to avoid influences of electric noises on the darker area of the
screen.
Brightness
Not detection
Noise
6
Magnitude of brightness shift
Time
Set the magnitude of changes in brightness. This feature is used
to disregard a sudden and huge change in brightness such as one
caused by turning on/off the lights.
7
Duration
Set the time the system should continue monitoring before identifying a moving object. This feature enables the system to neglect
high speed objects such as automobiles.
*The intelligent Digital Motion Detector function is not available when the electronic
sensitivity is set to ON or when the electronic shutter is set to “long mode”.
Features
x32 electronic sensitivity
When the illuminance of the monitoring point drops down,
electronic sensitivity can be automatically increased to x32
(max.) to brighten up the image. The minimum illuminance on
the object is 0.05 Lux (using F1.2 lens) which makes it possible to obtain a clear picture with almost no light at all.
The automatic increase in gain can be set to x2, x4, x8, x16,
or x32.
The camera can even cope with a gradual and continuous
change in illuminance from day to night and maintains a crisp
picture by successive adjustments of the auto iris, auto gain
control, and electronic shutter.
When the electronic sensitivity is set to ON
High quality image with DSP
The adoption of a new DSP (Digital Signal Processor) has
brought up the quality standard of the monitored image for reliable surveillance.
1) By digitizing the Colour processing, Colour reproduction has
been largely enhanced.
2) DSP maintains crisp borders and also restricts smear and
smudges of Colour. It further enables a wide choice of settings to control the degree of edge compensation.
Three types of white-balance adjustment
1) Automatic tracking mode to adjust white-balance as the light
(Colour temperature) at the monitoring point changes.
2) Push-and-lock mode to adjust white-balance when the set
button is pushed.
3) Manual white-balance by adjusting R and B volume.
Camera ID display
An 8-character (max.) camera ID can be super-imposed on the
monitor. The user can change the display to any position on
the screen.
Three types of synchronization
Internal, line lock, or external sync. can be selected. Selection
= between internal and line lock sync. mode is done
on-screen. The camera automatically switches to external
sync. mode by receiving a VBS. (Line lock sync. mode is available only with 24 V AC power supply.)
Dual power operation
24 V AC or 12 V DC applicable.
13 mode electronic shutter
Short mode: 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000,
1/4000, and 1/10000 sec.
Long mode: 2/50, 4/50, 8/50, 16/50, and 32/50 sec.
1/3" CCD image sensor with approx. 470,000 picture elements
480 TV lines of horizontal resolution
Electronic iris (indoor use)
On-screen settings
Camera settings can be easily controlled through on-screen
menus. A new setting will be reflected on the monitor to make
optimum settings easy.
Menu languages built in: English / French / Germany
x8 digital zoom with digital pan and tilt
Digital zoom of x2, x4, and x8, or continuous zooming up to x8
is available. The center of zooming can also be moved around
in all directions. Zooming can be controlled via SSP or by
means of a remote control circuit.
Two types of backlight compensation with fine tuning
1) Multi-spot photometry mode setting
This mode enables the user to specify screen areas, among 32
blocks, in which illuminance measurements will not take place.
The picture display will be kept to optimum brightness according to the illuminance measurements obtained in other areas.
Areas in which illuminance will
not be measured
2) 5-section photometry mode setting
The screen will be divided into 5 sections to which the user
will assign 15-scale weights.
The brightness of the picture will be kept at optimum by giving
priority to the area with the higher weight. (A DC type auto-iris
lens is required to enable this mode.)
SSP
Security Serial Protocol
SSP (RS-485) compatibility
The whole security system, including the VCC-6975P, may be
controlled by a VSP-7000 system controller using a new communication protocol SSP (Security Serial Protocol).
Remote control functionality on VSP-7000 includes all
on-screen menu items of the VCC-6975P.
SSP: Bi-directional communications (half duplex)
Maximum cable length for communication up to 1200 m (4000 feet)
VCC-6975PVCC-6975PVCC-6975P VCC-6975P
Command
Alarm
Multiplexer VCR VSP-7000
Up to 256
devices
1
1
15 1010
15 1010
5
5
An example of weight setting:
Top = 1, Bottom = 5, Left = 10,
Right = 10, Center (fixed) = 15.
The size and position of the center area is adjustable.
System Controller VSP-7000 (sold separately)
VCC-6975P rear panel
*Specifications subject to change without notice
please consult the instruction manual to ensure safe and proper operation of th
e product.
*Caution:
Video output terminal
Type of coaxial cable and maximum length
• Cable type RG-59U (3C-2V), 250 m maximum
• Cable type RG-6U (5C-2V), 500 m maximum
• Cable type RG-11U (7C-2V), 600 m maximum
Y/C signal output terminal
Type of coaxial cable and maximum length
• Mini-DIN round type 4-pin, 10 m maximum
SSP terminal
Power supply terminals
24 V AC and 12 V DC dual power capability
eliminates limitations on camera location.
Synchronization
signal input terminal
Camera Set-up Unit
VAC-60
Remote set-up makes you feel you have the camera right
beside your monitor. Capable of setting up VCC-6975P
for all on-screen menu items (intelligent digital motion
detector, backlight compensation, white-balance, etc.)
For better picture quality, disconnect this unit after
settings are completed.
(sold separately)
CURSOR
SET
VCC-6975P
LENS
VCC-6975P
67
1 126.5 9.5
LENS 4-pin
(Unit: mm)
CURSOR
LENS
SET
54
28
15.4
ADJ. LOCK
FLANGE BACK
25.2
COLOR CCD CAMERA
VCC-6975PMODEL
Scanning system
Image sensor
Picture elements
Horizontal resolution
Minimum illumination
Electronic sensitivity
Video output level 1.0 V (p-p) (75 ohms, composite)
Video S/N ratio More than 48 dB
Backlight compensation
White balance
Gain control
Gamma ON ( γ = 0.45) / OFF ––– (on screen)
Electronic shutter
Light control
Lens mount
Flange back
Auto iris lens
Auto iris output
Lens iris level
Electronic iris
Electronic iris range
Synchronizing system
V phase adjustment
Motion detector
Electronic zoom
Mirror image effect H, V, H/V, 3 mode reverse image
Camera ID ON (up to 8 characters) / OFF ––– (on screen)
Video signal
Y/C signal out mini-DIN 4-pin (rear)
SSP (RS-485) RS485 (G, B, A) ––– Pushbutton terminal x 1 pair (rear)
Sockets
Alarm signal ALARM (C, A) ––– Pushbutton terminal x 1 pair (rear)
External sync.
Auto iris lens
Power supply
Environmental conditions
Power requirement
Power consumption (approx.)
Camera mount
Dimensions (approx.)
Weight (approx.)
*Caution:
please consult the instruction manual to ensure safe and proper operation of th
please consult the instruction manual to ensure safe and proper operation of the product.*Caution:
PAL standard 625 lines, 25 frames/sec.
1/3" (approx. 4.8 mm x 3.6 mm) interline transfer method CCD
Total: 795(H) x 596(V), Effective: 752(H) x 582(V)
480 TV lines
Approx. 0.05 Lux (F1.2, x32 electronic sensitivity)
Approx. 1.4 Lux (F1.2, normal mode)
ON / OFF ––– (on screen)
ON = x2 / x4 / x8 / x16 / x32 ––– (on screen)
Multi-zone light measuring system
ON / OFF ––– (on screen)
ON = Multi-spot photometry / 5-section photometry ––– (on screen)
(TTL) ATW / AWC / Manual ––– (on screen)
ON (Automatic) / OFF ––– (on screen)
Short mode: 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 sec. ––– (on screen)
Long mode: 2/50, 4/50, 8/50, 16/50, 32/50 sec. ––– (on screen)
Optical auto iris lens / Electronic iris (indoor use)
CS / C mount (C mount: using C-mount adaptor supplied)
12.5 mm ±0.5 mm adjustment
DC / VIDEO ––– Slide SW (side)
DC: Drive coil (+, -), Brake (Damp) coil (+, -)
VIDEO: +12 V DC (Max. 50 mA), Video output (high-impedance)
LEVEL: L~H ––– (on screen)
ON / OFF ––– (on screen)
1.4 Lux to 70,000 Lux (F1.2), 2.0 Lux to 100,000 Lux (F1.4)
Internal sync. / Line lock ––– (on screen)
External sync.
LINE PHASE ––– (on screen)
ON / OFF ––– (on screen)
Alarm out: RS485 (G, B, A) and ALARM (C, A)
ON / OFF ––– (on screen)
ON = Continuance (up to x8), Fix (x2 / x4 / x8), Pan / tilt operation
VIDEO OUT ––– BNC (rear)
VBS IN ––– BNC (rear)
LENS ––– 4-pin (side)
24 V AC, GND ––– 3-pin terminal (rear) 12 V DC ––– 2-pin terminal (rear)
Temperature: -10°C to 50°C [14°F to 122°F], Humidity: within 90% RH
24 V AC, 50 Hz or 12 V DC
24 V AC: 4.0 W (with auto iris lens), 12 V DC: 4.1 W (with auto iris lens)
1/4"–20 UNC (top / bottom selectable)
67(W) x 54(H) x 126.5(D) mm
[2.64(W) x 2.13(H) x 4.98(D) in.] (w/o camera & lens mounts)
470 g [16.6 oz.] (w/o lens)
*Specifications subject to change without notice
*Specifications subject to change without notice
136
DIGITAL
11
1/4"–20 UNC threaded hole
(top / bottom selectable)
automatic switching
VAC-60
Video output terminal
Camera input terminal
Environmental conditions
Power requirement
Dimensions
Weight (approx.) 230 g [8.1 oz.]
AC adaptor
VCA-35E
Power requirement
Power consumption (approx.)
Dimensions (approx.)
Weight (approx.)
Monitor
VAC-60MODEL
BNC x 1
BNC x 1
Temperature: 0°C to 40°C [32°F to 104°F], Humidity: 10 to 90%
3 V DC, Alkali type AAA format batteries x 2
90(W) x 135(H) x 36(D) mm [3.54(W) x 5.32(H) x 1.42(D) in.]
(for VCC-6975P)
(sold separately)
VCA-35EMODEL
220 ~ 230 V AC, 50 Hz
17 VA max.
68(W) x 62(H) x 100(D) mm [2.68(W) x 2.44(H) x 3.94(D) in.]
680 g [24 oz.]
Lenses for 1/3" CCD camera
Super Wide-angle Lens
Wide-angle Lens
Standard Lens
x 6 Manual Zoom Lens
VCL-CS2LYA
VCL-CS4LY
VCL-CS8LY
VA-TS6ZE-LY
x 6 Motorized Zoom Lens
x 10 Motorized Zoom Lens
Pinhole Lens
Vari-focal Lens
SSP corresponding devices
System Controller
SSP System Controller
Multiplexer
16-channel Duplex Multiplexer (Colour)
16-channel Duplex Multiplexer (B/W)
9-channel Duplex Multiplexer (Colour)
9-channel Simplex Multiplexer (B/W)
Realtime VCR
168-hour Recording + Realtime VCR
40-hour Recording + Realtime VCR
Time Lapse VCR
960-hour Recording Time Lapse VCR
168-hour Recording Time Lapse VCR
24-hour Recording Time Lapse VCR
*More models will be introduced soon.
VSP-7000
MPX-CD162P
MPX-MD162P
MPX-CD92P
MPX-MS92P
SRT-7168P
SRT-6000P
TLS-9960P
TLS-9168P
TLS-9024P
e product.
VAC-60 rear panel
VA-TS6ZME-LY
VA-TS10ZME-LY
VA-TS420PE-LY
VA-TS2VE-LY
As of March 2000
Distributed by:
SANYO Electric Co., Ltd.
Video Imaging Systems Division
© 2000 SANYO Printed in Japan '00.3. AP
Loading...