Sanyo VCC-6574PC Instruction Manual

Page 1

INSTRUCTION MANUAL

VCC-6574PC

COLOR CCD camera

About this manual

Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.

Dimensions: mm

109

0.5

12.6

22.4

100

1/4”–20 UNC

Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer.

NAMES AND FUNCTIONS OF PARTS

Contains camera adjustment dials and setting switches.

Used to connect the lens plug when the lens is attached.

Connects to the video input terminal on the peripheral equipment.

When using two cameras or more, the image on the monitor may roll vertically when switching sources. This rolling can be minimized by turning

long screws

short screws

Lens cap

Protects the lens from damage.

FLANGE BACK ADJ. (Flange-back adjustment screw)

FLANGE BACK LOCK (Flange-back lock screw)

Locking screw for the flange-back adjustment screw.

Camera attachment bracket

The bracket can be secured at the top or bottom of camera. When securing the bracket, use the long screws and use the short screws on the opposite side to seal the openings.

When installing the camera support, select a location that can support the total weight of the camera and accessories.

this dial.

Lights when the camera power is ON.

The 1/3-inch DC type, CS mount auto-iris lens (sold separately) is recommended.

1 Remove the lens cap. 2 Attach the lens.

3 Connect the lens plug to the LENS

Camera adjustment/setting panel

LENS (Lens iris output terminal)

VIDEO OUT (Video output terminal: BNC connector)

LINE PHASE (Line phase adjustment dial)

POWER (Power indicator)

GND, AC24V (Ground terminal, AC 24 V input terminal)

Attaching a lens

Turn the lens slowly to attach it to the camera.

terminal.

When using different shape or specification of the plug, connect the supplied lens iris plug.

When attaching the lens, use a lens with a mount screw

(L) that is less than 5 mm in length. If a lens that exceeds this size is used, the camera may be damaged and you may not be able to attach it correctly.

When attaching a C mount lens, attach the lens to the

camera after inserting the C mount ring (sold separately).

When using different shape of the lens plug

Rewire the lens cable in the supplied lens iris plug.

DC type lenses VIDEO type lenses

Brake coil (-) DC +12 V (50 mA max.)

Brake coil (+) Not used

Drive coil (+) Video output (1.0 V(p-p), high impedance)

Drive coil (-) Ground (for video signal and DC power)

1 Prepare the lens cable.

Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire.

8 mm

2 m

2 Install the lens iris plug.

Solder the cable to the pins following the correct pin layout, then close the

plug cover.

1AC6P1P2802-L53X4/C (0304TR-TT)

SANYO Electric Co., Ltd.

PRECAUTIONS

In case of problem

Do not use the camera if smoke or strange odors come from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer or a Sanyo Authorized Service Center.

Do not open or modify

Do not open the cabinet, as it may be dangerous and cause damage to the unit. For internal settings and repairs, consult your dealer or a Sanyo Authorized Service Center.

Do not put objects inside the unit

Make sure that no metal objects or flammable substances get inside the camera. If used with a foreign object inside, it could cause fire, short-circuits or damage. If water or liquid gets inside the camera, disconnect the power cord immediately, and consult your dealer or a Sanyo Authorized Service Center. Be careful to protect the camera from rain, sea water, etc.

Be careful when handling the unit

To prevent damage, do not drop the camera or subject it to strong shock or vibration.

Install away from electric or magnetic fields

If installed close to a TV, radio transmitter, magnet, electric motor, transformer, or audio speakers, the magnetic field they generate will distort the image.

Protect from humidity and dust

To prevent damage to the camera, do not install it where there is greasy smoke or steam, where humidity may get too high, or where there is a lot of dust.

Protect from high temperatures

Do not install close to stoves, or other heat generating devices, such as spotlights, or where it could be subject to direct sunlight, as that could cause deformation, discoloration or other damage. Be careful when installing close to the ceiling, in a kitchen or boiler room, as the temperature may rise to high levels. Install where the temperature range will stay between -10°C (14°F) and 50°C (122°F). (no condensation)

Cleaning

Dirt can be removed from the cabinet by wiping it with a soft cloth.

To remove stains, use a soft cloth moistened with a soft detergent solution and wrung dry, then dry by wiping with a soft dry cloth.

Do not use benzine, thinner or other chemical products on the

cabinet, as they may cause deformation and paint peeling. Before using a chemical cloth, make sure to read all accompanying instructions. Make sure that no plastic or rubber material comes in contact with the cabinet for extended periods, as that may cause damage or paint peeling.

TROUBLESHOOTING

Before sending the camera out for repair, check the items below. If the problem persists after checking these items, consult your dealer or a Sanyo Authorized Service Center.

If no image appears

Are the power and voltage normal? Are all the signal connecting cables correctly connected? Is there adequate illumination? Has the lens cap been removed? Is the lens type (DC or VIDEO) correctly selected?

Depending on the type of lens, the A. I. LENS switch must be set accordingly.

Has the iris of the lens inside the camera been adjusted correctly

(with the lens iris dial)?

If the image is unclear

Is the monitor adjusted correctly? Is the flange-back position correctly set? Is the lens in focus? Is the lens dirty?

Dirt or fingerprints on the lens can adversely affect the image. Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid (commercially available).

SERVICE

The camera is a precision instrument. Handle it carefully and always follow the safety precautions. If the camera requires service, never try to repair it yourself or open the casing. For servicing, maintenance, or repairs, consult your dealer or a Sanyo Authorized Service Center.

SPECIFICATIONS

Scanning system : PAL standard (625 TV lines, 25 frames/s) Interlace : PLL 2:1 interlace Image device : 1/3 inch solid state image device CCD Effective picture

elements Synchronizing system : Internal sync/Line lock (manually switchable) Resolution : 520 TV lines horizontally, 400 TV lines vertically Video output level : 1.0 V(p-p)/75 Ω, composite Video S/N ratio : More than 48 dB Aperture : Sharp/Normal (manually switchable) Minimum required

illumination (incandescent lighting)

Backlight compensation

Iris function : Electronic-iris/Auto-iris (manually switchable) Electronic shutter : 8 speeds, selectable by switches:

White balance : Auto/Manual switching Lens mount : CS mount Environmental

conditions Power supply : AC 24 V, 50 Hz Power consumption : Approx. 3.5 W (with auto-iris lens)

Weight : Approx. 310 g (without lens) Accessories : Lens iris plug (with the plug cover)

Features and specifications are subject to change without prior notice or obligations.

: 752 (H) x 582 (V)

: Approx. 1.0 lx (F 1.2 lens)

: Selectable by switches:

Multi-spot metering system/Center-weighted metering system/OFF

1/50 - 1/10000 s

: Temperature: -10°C ~ +50°C

Humidity: less than 90%RH (no condensation)

Approx. 2.6 W (with manual or fixed iris lens)

Page 2

CONNECTIONS AND INSTALLATION

LINE

PHASE

ADJUSTMENT AND SETTINGS

CONNECTIONS

Monitor

Video signal : VIDEO IN

: VIDEO OUT

Degital video recorder or time-lapse VCR

CONNECTIONS

What you need

Peripheral equipment (such as monitor, digital video recorder or time-

lapse VCR)

Cables for connecting peripheral equipment and camera (coaxial cables,

connecting plug)

Power adapter (AC 24 V)

Supported coaxial cables

You can use any of the following coaxial cables:

RG-59U (3C-2V) Length: 250 m max. RG-6U (5C-2V) Length: 500 m max. RG-11U (7C-2V) Length: 600 m max.

When using an RG-59U (3C-2V) cable, do not use it on piping or air

wiring.

Select the cable according to the distance between the devices you wish

to connect.

If you use a cable other than the types above, the image or sync signal

will be attenuated and will not be transmitted correctly.

Making connections

1 Connect the camera and peripheral equipment with cables. 2 Connect the power cable.

Connect 3 wire grounded cable (# 18 AWG+).

To prevent a fire hazard use any UL listed wire rated VW-1 for the AC 24 V input terminal.

3 Insert the plug of this power cord into a wall outlet.

The POWER indicator will light.

VIDEO OUT

AC 24V

POWER

Push to insert the cable.

AC 24V

FLANGE BACK ADJUSTMENT

If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the FLANGE BACK position as described below.

1 Using a + screwdriver, loosen the

FLANGE BACK LOCK screw (M2:+).

2 Set the zoom lens to the maximum

telephoto position, and set the focus using the focus ring on the lens.

3 Set the zoom lens to the maximum

wide angle position, and set the focus using the FLANGE BACK ADJ. screw.

Repeat steps 2 and 3, until the image stays in focus when changing from a telephoto shot to a wide angle shot.

4 When the setting is complete, tighten

the FLANGE BACK LOCK screw.

2, 3

ADJ.

FLANGE BACK

1, 4

LOCK

The illustration shows the factory default settings for the switches in the camera adjustment/setting panel.

VR303

VR302

6785

1093421

2 4 5 63

IRIS SYNCAPER BLC WBES

123

The sticker on the inside of cover.

The camera comes pre-adjusted and ready to install at time of factory shipment, but you may want to make adjustments or settings to adapt to the operating conditions or installation environment. If you have trouble adjusting the camera, consult your dealer or a Sanyo Authorized Service Center.

Iris setting (IRIS) and electronic shutter speed

setting (ES)

Select iris setting when using either lens below.

AI When using an auto-iris lens, set the IRIS switch 4 and

EI (for indoor use) When using a manual or fixed iris lens, set the IRIS

Electronic shutter speed settings

1/50 1/120 1/250 1/500 1/1000 1/2000 1/4000 1/10000

123 123 123 123 123 123 123 123

Using the high speed electronic shutter indoors with low lighting, will give

darker pictures. In such a case, add some lights to make sure the lighting is sufficient.

If the lighting is very bright, pay attention to the light angle in order to

avoid or minimize the smear phenomenon effect.

If using a manual or fixed iris lens under fluorescent light, the image may

flicker.

Outline compensation (APER:Aperture)

SHRP Emphasizes object outlines.

NORM When object outlines appear too strong.

EI LLSHRP CENT ON MANU

AI INTNORM MULT OFF ATWMSB LSB

select electronic shutter speed.

switch 4. * Set the lens aperture to the shortest F stop.

VR301

DC VIDEO

A. I.

LENS

This switch is not used.

(Unit: seconds)

Backlight compensation (BLC)

You can set the metering area ( ), to have the lens iris adjust automatically to make the image easy to see when the object is backlit. (Active when using an auto-iris lens.)

When applying backlight compensation to the whole of the screen.

When applying backlight compensation to only the central portion of the screen.

Color compensation (WB:White balance)

MANU Lets you fine-tune the white balance manually.

ATW Compensation is performed automatically.

Sync setting (SYNC)

LL Line-Lock: Synchronizes the unit with power frequency.

INT Internal Sync

• R (Red) dial : Turn clockwise to augment screen red.

• B (Blue) dial : Turn clockwise to augment screen blue.

• If the image on the monitor rolls vertically when two or more cameras are connected, refer to “Line phase adjustment dial” below.

R B

Multi-spot metering

The screen is divided into 64 areas, and each area is metered and backlightcompensated.

If the background of the object is extremely dark, the center of the object may be too bright. In this case, set center-weighted metering mode.

Center-weighted metering

Only the central portion of the screen is metered and backlight-compensated.

5R5

Line phase adjustment dial

When sync setting is set to Line-Lock (LL) and two or more cameras are

connected, the image displayed on the monitor may roll vertically. If using this product as the second or

subsequent camera; Adjust the roll by turning the LINE PHASE dial.

If using this product as the first camera;

Adjust the roll by turning the line phase adjustment dial on the second and subsequent cameras.

Lens setting (A.I. LENS)

Set this as appropriate for the type of lens you are using.

VIDEO VIDEO type auto-iris lens (lens with built-in amp circuits)

DC DC type auto-iris lens (lens without built-in amp circuits,

When using a VIDEO type auto-iris lens, turn the ALC (light control) dial on the lens barrel fully to AV (average).

Lens iris dial

If the entire image is too dark or too bright when using an auto-iris lens (AI), adjust this dial ( ).

Counterclockwise Closes the lens iris, making the entire image darker.

Clockwise Opens the lens iris, making the entire image brighter.