Sanyo VA-80BP Instruction Manual

INSTRUCTION MANUAL

Pendant Mounting Bracket

This installation should be made by a qualified service
person and should conform to all local codes.

About this manual

This bracket is designed for ceiling mounting installation.
Before installing and using this unit, please read this manual carefully.

Be sure to keep it handy for later reference.

CAUTION:

Install this bracket securely according to this
installation manual. Be aware that allowing the
bracket to fall with the camera on it may cause
personal injury.

• Be careful when opening holes for installing the
unit. Work with the power and video cables pulled
out for easy installation.

• Make sure to properly perform waterproofing for the
ceiling where you are installing the unit.

• Make sure that the surface in the installation
location has no unevenness and is strong enough
to bear the total weight of the unit.

• Install this unit in an environment where the
temperature range stays between -30°C and +50°C
(-22°F and +122°F) (no condensation allowed).

VA-80BP

English

Important

日本語

Example of

indoor use

☞P1 ☞P2

Example of

outdoor use

Accessories (For outdoor housing)

Bolts (20 mm/0.8”)

Waterproof tape

Features and specifications are subject to change without
prior notice or obligations.

Waterproof gasket

Waterproof ring

bSpecifications

Color: Beige
Material: Metal
Waterproof Standard: Conforming to IP66
Weight: Approx. 700 g (1.5 lb)

Allowable Load: Max. 20 kg (44.1 lb)

Dimensions:

63 (2.5)

63 (2.5)

Ǿ130 (5.1)

Ǿ48

(1.9)

Unit: mm (inch)

Ǿ96 (3.8)

Ǿ8.5 (0.3)

PDǾ102 (4.0)

45˚

329 (13.0)

300 (11.8)

Indoor Type

Make sure to also consult the relevant instruction manuals.

Mark the locations on the ceiling and drill the holes

1

for the cables and screws.

And pull out the cables from the ceiling hole and
pass them through the bracket as shown in the
figure.

With sticker (A) facing toward you, fix the bracket

2

to the ceiling using commercially available screws
(B) in 4 places.

Mount the power board unit onto the attachment.

3

(1) Pass the screws supplied with the attachment

through each of the power board unit screw holes
(C) and fasten them loosely using washers
(4 places).

(2) Align the blue sticker (D) on the attachment and the

arrow (D) of the same color on the power board
unit, and tighten firmly the screws loosely
fastened in the previous step.

C

C

D; Blue

Fasten them loosely at two diagonal points using

4

the supplied bolts (E).
Thread the bolts (E) loosely fastened in step 4

5

through the bracket’s bolt holes (F) with sticker (A’)
aligned with sticker (A) and turn the bracket
clockwise.

Put the remaining bolts (E) to the other bracket bolt

6

holes and tighten the 4 bolts (F) securely.

• To fix the attachment, use the hexagonal wrench
supplied with the attachment.

• Make sure that the attachment is fixed, peel-off the
stickers.

Connect the cables to the power board unit and

7

mount the camera unit onto it.

☞ For details, please refer to Installation Manual that

comes with the camera unit.
“Connections and Settings”
“Surface Mount”

C

Power Board Unit:
VA-84S/80S

C

a

b

Attachment: VA-80A

2

1

B

A’

B

M8 (5/16”): 40 mm (1.6”) or more

A

4

E

5

F

E

A

A’

6

F

E

• Be sure to fix the bracket securely using M8 (5/16”)
screws. Using other bolt sizes may cause the bracket to
fall together with the camera on it.

• Route the connected cables so that they do not touch the
power board unit and other parts.

Screws, washers

(for power borad

1

Attachment accessories

b

E

a

Bolts (10 mm/0.4”)

unit)

Hexagonal

wrench