Sanyo VA-22W Instruction Manual

SPECIFICATIONS

Materials : Galvanized steel plate and ABS plastic Ambient temperature : –10 ~ +50˚C Dimensions : Refer to the dimension diagram below.

* The length of the support pole will vary according to customer

specifications.

Weight : Approx. 1.2 kg Accessories : M4 x 12 screws (3 pcs.)

Appearance and specifications are subject to change without notice.

Dimensions

46mm15mm

INSTRUCTION MANUAL

Wall Mounting Bracket

VA-22W

1AC6P1P2416-L9BBD/XE (0011KPS)

88mm

32mm

SANYO Electric Co., Ltd.

Printed in Japan

If the wall mounting bracket is not installed in the correct position, or if it is connected incorrectly, it may result in fire or electric shocks. In some cases severe injury or death may also result.

Install in a location which is strong enough to support the combined weight of the

•

camera and the wall mounting bracket for many years.

To prevent the possibility that the camera and wall mounting bracket may fall down, suspend a weight of 5 kg or more from the intended installation location using a metal chain or wire, and check that safety can be maintained.

Leave at least 1.5 m of space between the wall mounting bracket and air outlets

•

from equipment such as air conditioners.

If cold air is allowed to blow directly onto the camera, it may cause the lens to become cloudy, and this can adversely affect the quality of the recorded images.

Avoid installing the wall mounting bracket directly underneath ceiling water pipes

•

or places which might be subject to water leakage.

Condensation from water pipes may get inside the camera and cause fire or electric shocks.

Avoid places which are subject to vibration or noise.

•

Vibration and loud noise can cause the screws to loosen, which might damage the bracket or cause the camera and bracket to fall down. Furthermore, it may also cause the screen to shake and result in synchronization problems.

Be sure to use only the provided screws for installation.

•

Do not disassemble or modify the wall mounting bracket.

•

Failure to observe this may cause the bracket to become damaged or fall down.

INSTALLING THE BRACKET AND CAMERA

before installing the wall mounting bracket, route any cables which are to be connected to the camera through the ceiling. Furthermore, after installing the bracket and camera, check that they are securely installed so that there is no danger they will fall down.

Preparation

1 Make a hole with a diameter of 40 ~ 50 mm

in the ceiling.

2 Make a hole in the mounting plate A (which

will be used to support the weight of the bracket and camera) which is the same size as the hole in the ceiling.

3 Make three holes B (3 ~ 5 mm) for the

screws which will secure the camera support pole C.

4 Loosen the screws E of the clamper D which

is secured to the support pole C, and then remove the fitting F from the support pole C.

5 Loosen the screw H of the veneer ring G so

that the veneer ring G can move freely.

6 Place the mounting plate A, fitting F and

spacer I onto the top side of the ceiling.

Caution

Use a ceiling location and a mounting plate

•

which can support the combined weight of the wall mounting bracket.

The customer should provide the spacer I.

•

74mm

Installation to the ceiling

1 Pass the support pole C through the hole in

the ceiling.

2 Pass the support pole C though the hole in

40~50mm

the mounting plate A on the top side of the ceiling, and position the spacer I underneath

the mounting plate A.

3 Insert the support pole C into the fitting F,

and then secure the fitting F to the mounting plate A with the three screws J.

4 Tighten the screws E of the clamper D. 5 Place the veneer ring G against the ceiling,

and then tighten the screw H at that position.

Installing the camera

1 Pass the cables which are to be connected to

the camera through the support pipe C.

2 Attach the fitting K to the camera using the

three screws L (M4x12) which are provided.

3 Connect the power supply, RS485 and signal

cables to the connection terminals on the camera.

Refer to the Instruction Manual for the camera for details on connecting each of the cables.

Caution

After installing the bracket and camera, paint the screws to prevent them from loosening.

4 Install the cover M.