Sanyo VA-22ME Instruction Manual

SPECIFICATIONS

Materials: : Zinc plated metal and ABS plastic
Environmental condition: : Temperature: –10 ˚C ~ +50 ˚C

Humidity: less than 90 %

Dimensions: : Approx. 197 (W) x 175 (H) mm
Weight: : Approx. 900 g
Accessories: : M3x8 screws (4)

Features and specifications are subject to change without prior notice or obligations.

175 mm

197 mm

INSTRUCTION MANUAL

Ceiling recessed mounting bracket

VA-22ME

1AC6P1P2339-­L9BBC/XE (0400KP-NI)

SANYO Electric Co., Ltd.

Printed in Japan

Improper mounting and/or connections may result in electric shock, fire or cause death or
serious injuries.

The ceiling must be strong enough to support the weight of the camera and its

•

accessories (approx. 3 kg).
The bracket must be installed at a minimum distance of 1.5 m from the air outlet of

•

an air conditioning

If cold air is directed onto the camera, that may fog the lens and the image may be blurred.

Do not install the bracket where there is a risk of water leaking from pipes, etc.

•

Condensation on pipes may cause water dripping onto the camera and cause a fire and/or
electric shocks.

Never mount to a ceiling surface that may be subjected to vibration or shocks

•

Vibrations may loosen the screws and cause the camera to fall down. They may also cause
rolling of the image and the synchronization signals may not be transmitted correctly.

Do not modify or change

•

Any modification to the bracket may cause the camera to fall or other problems.

INSTALLATION

Before starting the installation of the bracket, run the power supply cord and other cables
behind the ceiling.

When the installation is finished, make sure it is secure and that there is no risk of the bracket
falling down.

Preparation

1 Cut a hole of 160 – 170 mm in diameter into

the ceiling.

The ceiling thickness can be 5 – 45 mm

•

There must be 170 mm or more between

•

the counterceiling and the ceiling structure.

2 Anchor bolt (A) must be firmly attached to

the ceiling structure, at the center of the
opening.

NOTE:

If the anchor bolt cannot be used due to the
building structure, use any commercially
available chain or cable that can withstand a
load of 5 kg or more.

3 Turn the bezel (B) counterclockwise, to

remove it from the recessed mounting
bracket (C).

4 Loosen the three M4 screws (D) of the

recessed mounting bracket (C), then pull the
camera holder (E) out while pressing the tabs
(3 places) inward.

5 Attach the camera unit to the camera holder

(E) using the 4 supplied M3x8 screws (F).

160 ~ 170 mm

C

D

D

B

Installation

Ceiling structure

A

170 mm or more

Ceiling thickness
up to 45 mm

1 Push in the 3 hooks (G) on the recessed

mounting bracket (C), then insert the
recessed mounting bracket (C) into the
mounting hole. Attach the recessed
mounting bracket (C) to the anchor bolt (A)
using the two nuts (H).

2 Push out the 3 hooks (G), and lower them

until they touch the back of the mounting
ceiling.

A

H

C

G

3 Tighten the three holding screws (I) evenly to

attach the recessed mounting bracket (C).

D

E

F

E

4 Connect the power supply cord, the RS485

and signal cables to the camera unit
connectors. For detailed information on
connections, please refer to camera
instruction manual.

5 Insert the camera unit in the recessed

mounting bracket (C) with the camera
connectors located on the upper opposite
side of the lens, then tighten the three M4
screws (D) to attach the camera holder (E).

6 Align the 3 tabs on the inside of the bezel (B)

with the hooks on the recessed mounting
bracket (C), then turn the bezel clockwise to
lock it in place.

G

D

I

E

B