SANYO STK400-020 Datasheet

Overview

Now, thick-film audio power amplifier ICs are available
with pin-compatibility to permit a single PCB to be
designed and amplifier output capacity changed simply by
installing a hybrid IC. This new series was developed
with this kind of pin-compatibility to ensure integration
between systems everywhere. With this new series of IC,
even changes from 3-channel amplifier to 2-channel
amplifiers are possible using the same PCB. In addition,
this new series of ICs has a 6/3 Ω drive in order to support
the low impedance of modern speakers.

Features

• Pin-compatible
STK400-000 series (3-channel, single package)

STK401-000 series (2-channel, single package)

• Output load impedance RL=6 Ω/3 Ω supported

• New pin assignment
To simplify input/output pattern layout and minimize
the effects of pattern layout on operational
characteristics, pin assignments are grouped into blocks
consisting of input, output and power systems.

• Few external circuits
Compared to those series used until now, capacitors and
bootstrap resistors for external circuits can be greatly
reduced.

Package Dimensions

unit : mm

4086A

Thick Film Hybrid IC

N3096 HA (OT)/D2894 TH(OT) No. 4830-1/10

[STK400-020]

SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters

TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN

3-Channel AF Power Amplifier (Split Power Supply)

(15 W + 15 W +15 W min, THD = 0.4 %)

STK400-020

Ordering number : EN4830A

➙

Parameter Symbol Conditions Ratings Unit

Maximum supply voltage V

CC

max ±29 V

Thermal resistance

θj-c Per power transistor 2.1 °C/W
Junction temperature Tj 150 °C
Operating substrate temperature Tc 125 °C
Storage temperature range Tstg –30 to +125 °C
Permissible load short time t

s

V

CC

= ±20 V, RL = 6 Ω, f = 50 Hz, PO = 15 W 1 s

Specifications

Maximum Ratings at Ta = 25°C

Operating Characteristics at Ta = 25°C, RL= 6 Ω, Rg = 600 Ω, VG = 40 dB, RL(noninductive)

Internal Equivalent Circuit

Notes

• Use rated power supply for testing unless otherwise specified.

• When measuring permissible load short time and output noise voltage, use transformer power supply indicated below.

• Output noise voltage is represented by the peak value rms (VTVM) for mean reading. Use an AC stabilized power
supply (50 Hz) on the primary side to eliminate the effect of AC flicker noise.

No. 4830-2/10

STK400-020

Parameter Symbol Conditions min typ max Unit

Quiescent current I

CCO

VCC=± 24 V 30 90 150 mA

Output power

P

O

(1) VCC= ±20 V, f = 20 Hz to 20 kHz, THD = 0.4% 15 20 W

P

O

(2) VCC= ±16 V, f = 1 kHz, THD = 1.0%, RL= 3 Ω 15 20 W

Total harmonic distortion

THD (1) V

CC

= ±20 V, f = 20 Hz to 20 kHz, PO= 1.0 W 0.4 %

THD (2) V

CC

= ±20 V, f = 1 kHz, PO= 5.0 W 0.02 %

Frequency response f

L

, f

H

VCC= ±20 V, PO= 1.0 W, dB 20 to 50 k Hz

Input impedance r

i

VCC= ±20 V, f = 1 kHz, PO= 1.0 W 55 kΩ

Output noise voltage V

NO

VCC= ±24 V, Rg = 10 kΩ 1.2 mVrms

Neutral voltage V

N

VCC= ±24 V –70 0 +70 mV

+0
–3

Pattern Example for PCB Used with Either 2- or 3-Channel Amplifiers

Sample Application Circuit

No. 4830-3/10

STK400-020