SANYO C1461FEDIV, C1461TX, C1461TX-C, C1461TXC, C1461TXP, C1465TX, C1471TX, C1471TXH, C1710TX, C1710TXAH, C17AT1, C17AT1C, C2161TX-C, C2161TXC, C2165, C2165TX, C2170CE, C2170TX, C2180, C2180A, C2180TXA, CE17AT1, CE17AT1C
SANYO SANYO C1461FEDIV, C1461TX, C1461TX-C, C1461TXC, C1461TXP, C1465TX, C1471TX, C1471TXH, C1710TX, C1710TXAH, C17AT1, C17AT1C, C2161TX-C, C2161TXC, C2165, C2165TX, C2170CE, C2170TX, C2180, C2180A, C2180TXA, CE17AT1, CE17AT1C Service manual & schematics
Page 1
Service Manual
Colour Television
CRT 21" A51EFS83X191 CRT 21" A51EAL155X10
CHASSIS No 2096 EC4A TXT
| 1SAFETY INSTRUCTIONS. | 1 |
|---|---|
| 1.1 WARNING. | 1 |
| 1.2 PRECAUTION AGAINST X-RAYS | 1 |
| 2TECHNICAL CHARACTERISTICS | 2 |
| 2.1SAFETY | 2 |
| 2.2EMC (Electromagnetic Compatibility) | 2 |
| 3SPECIAL MODE FOR FACTORY | 2 |
| 4 CONFIGURATION CODE OPTIONS(OPCODE) | 2 |
| 5PROCEDURE OF NON VOLATILE MEMORY (NVM) REPLACEMENT, IC125 | 3 |
| 6DESCRIPTION OF HOTEL MODE. | 3 |
| 7ACTIVATION OF THE INITIAL AUTOMATIC CHANNEL-SEARCH | 3 |
| 8 BLOCK DIAGRAM | 4 |
| 9 SERVICE ADJUSMENT LOCATIONS | 5 |
| 10 ADJUSTMENT | 6 |
| 10.1 Notes about the adjustment | 6 |
| 11 CABINET PARTS LIST | 7 |
| 12 C2170TX-P CABINET PARTS LIST | 7 |
| 13 - CHASSIS ELECTRICAL PARTS LIST |
Give complete "SERVICE PART No" for parts order or servicing, it is shown on the rating sheet on the cabinet back of the TV set.
Note
This TV receiver will not work properly in foreign countries where the television transmission system and power source differ from the design specifications. Refer to the specifications for the design specifications.
Page 2
1.-SAFETY INSTRUCTIONS.
Read this page before doing any operation of adjustment, maintenance or repair the TV set described.
Only skilled personnel of Sanyo Technical Service should do the adjustment, maintenance or repair of TV set.
1.1.- WARNING.
For the correct and safe use of the TV set, it is essential that the service personnel follow the process of safety generally accepted and the safety precautions specified in this manual.
An isolation transformer should be connected in the power line between the receiver and the AC line when a service is performed on the primary side of the converter transformer of the set.
1.2.- PRECAUTION AGAINST X-RAYS.
The primary source of X-RADIATION in the television receiver is the picture tube. The picture tube is specially constructed to limit X-RADIATION emissions. For continued X-RADIATION protection, the replacement tube must be the same type as the original including suffix letter. Excessive high voltage may produce potentially hazardous X-RADIATION. To avoid such hazards, the high voltage must be maintained within specified limit. If high voltage exceeds specified limits, take necessary corrective action. Carefully follow the instructions for +B1 volt power supply adjustment, and high voltage adjustment to maintain the high voltage within the specified limits.
COMPLIANCE TO STANDARDS
All of those marked with * or A must be replaced with original parts
WARNING! This TV set contains components which are particularly sensitive to static electricity (ESD).It is recommended that all due precaution be taken handling integrated circuits and semiconductors.
Page 3
2.-TECHNICAL CHARACTERISTICS
| Cathode-ray tubes | In-Line gun type.21" (54 cm) |
|---|---|
| Tuning-system | Voltage synthesis, 50 programs in non-volatile memory, AFT, fine tuning, |
| automatic, semiautomatic and manual channel-search. | |
| Program selection | Sequential selection from the controls on the set. Direct selection of any |
| program from the remote-control device. | |
| Receiving channel | E2E4; S1S10 |
| E5E12; S11S41 | |
| E21E69 | |
| Reception system | System B/G |
| Colour system | PAL |
| Power-rating 3,5 watts. (RMS) 10% Distortion | |
| Number of speakers | 1 Full Range 8 Ω |
| Aerial | External aerial-socket 75 ohms IEC. |
| AV connectors | 1 Scart connector 21-pin standard CENELEC AV/RGB. |
| 1 RCA type video input (Back cover) | |
| 1 RCA type audio input (Back cover) | |
| Power source | 220V240V. AC 50 Hz |
| Power consumption | 80 Watts. (maximum consumption). |
| • | 5 Watts. (Stand-by condition) |
| Clock function | |
| Timer function | Switch on, off and alarm time delay are programmable in OSD over 24 |
| hours. | |
| Teletext | Flof and List 1.5 level. |
| Hotel mode | This TV set has the possibility of being programmed in Hotel mode. |
2.1.-SAFETY.
It fulfils the safety requirements established in the regulation.
- EN 60065:1993.
2.2.-EMC (Electromagnetic Compatibility).
It fulfils the EMC requirements established in the regulation.
- EN 55013:1990.
- EN 55013:1990/A12:1994
- EN 55020:1994.
- EN 60555-2:1987.
3.-SPECIAL MODE FOR FACTORY
The factory mode is a special TV working mode, thought to aid the manufacturing process and it is identified the message "FACTORY". This mode is not intended for customer use..
The Factory mode differences with respect to normal mode are the followings:
- 1.- The TV set does not pass to standby mode after 10 min. without aerial signal input. Instead it remains switched on.
- 2.- The adjustments speed is four times quicker.
- 3.- The standby mode is disabled.
To take TV set out of Factory mode, push the key TIMER of remote control.
4.- CONFIGURATION CODE OPTIONS(OPCODE)
The Opcode in this model is 31 .
In order to see the present Opcode in NVM, you have to short circuit the carcass of front keys with R146 (jack side). Then the code will appear in screen during several seconds. In this time it is possible to change it by using the numerical keys of remote control.
Page 4
5.-PROCEDURE OF NON VOLATILE MEMORY (NVM) REPLACEMENT, IC125:
In case of servicing, after NVM replacement, the following points must be checked:
• The Opcode (configuration code) is the right one.
Described in point 4
• The TV is not in FACTORY mode.
Described in point 3
• The Hotel mode is correct.
Described in point 6
• The picture and sound adjustments are correct
Described in point 10
• The OSD phase adjustment is correct.
Described in point 10
6.-DESCRIPTION OF HOTEL MODE.
By defect the TV set switches on with the program in which is was switched off, but it is also possible to force it to switch on in a program that can be chosen between the 1 and 8 or AV.
The TV set has a special mode of operation that is adapted for use in hotels, hospitals, etc. In this case the maximum volume level is limited to the volume chosen when the hotel mode is enabled. Furthermore, in this mode it is not possible to do channel searching neither to modify the fine tuning control.
These software configurations are stored in the non volatile memory and therefore they remain even though the TV set is disconnected from the power supply. The Hotel mode configuration can be changed by pushing the SET front key and without loosing it, pushing the key SIZE of remote control.
00 HOTEL
The first, most significant digit indicates weather Hotel mode is chosen or not
0 ⇔ Normal mode
1 => Hotel mode
The last, least significant digit indicates the programme in which the set switches on
- 0 ↔ The same as it was selected when the TV set was switched off.
- 1 ➡ Always programme position 1.
- 2 ↔ Always programme position 2.
8 ⊲> Always programme position 8.
9 ↔ Always AV mode.
The wanted code should be introduced with the numerical keys of remote control. Always to push the complete code.
Example:
00 Is Normal mode. Switches on with the same programme selected when the TV set was switched off.
10 -> Hotel mode. Switches on with the same programme selected when the TV set was switched off.
11 ↔ Hotel mode. Always switches on in programme 1
09 ⇒ Normal mode. Always switches on in AV mode
7.-ACTIVATION OF THE INITIAL AUTOMATIC CHANNEL-SEARCH.
In order to reset the initial automatic channel-search function, enter the tuning menu by keeping pushed the frontal SET key for a few seconds. Afterwards select the AUTO tuning mode by pushing several times the SET key. Then push the + or - key to start searching and switch-off the TV set before any station is found. When the TV set is switched on again it will remain in the same situation as when it was switched off.
Page 5
8.- BLOCK DIAGRAM
Page 6
9.- SERVICE ADJUSMENT LOCATIONS
Page 7
10.- ADJUSTMENT.
| ustment: | s about the adiu | |||||
|---|---|---|---|---|---|---|
| centre. | + and - | OPCODE menu. Described point 4 | pattern | |||
| Adjust to align the OSD vertical bar with the picture | Sound | CRT screen | TV controls: Normal O | Circular | Phase of OSD | 7 |
| Adjust to obtain the best possible focusing in the centre of screen. | FOCUS | CRT screen | TV controls: Normal 0 |
Circular
pattern |
Focus | 6 |
|
The potentiometers must be adjusted in order to obtain
an acceptable colour tone. In case of doubt, they must be adjusted to the same value of the divider R503/R504 |
VR501
VR502 |
CRT screen | Colour to minimum and rest of controls in normal |
Circular
pattern |
Tone | 5.D |
| Adjust the potentiometers corresponding to those cathodes that are not conducting, in order to obtain a tenuous line without colour tone (White) |
VR503
VR504 VR505 |
CRT screen | Brightness controls: Adjust Service Line |
AV Mode
Without signal |
Cut-off | 5.C |
| Set the G2 voltage for one colour to be just visible. |
G2
Potentiometer |
CRT screen | Brightness controls: Adjust G2 to minimum. Service Line |
AV Mode
Without signal |
G2 | 5.B |
| Turn the potentiometers completely anticlockwise (seen from solder side) |
VR503
VR504 VR505 |
Brightness controls: Adjust •
G2 to minimum. |
AV Mode
Without signal |
Cut-off
preadjustment |
5.A | |
|
Adjust VR600 to centre the picture in horizontal
direction. Readjust horizontal width if necessary. |
VR600 | CRT screen | TV controls: Normal |
Circular
pattern |
Horizontal
centre |
4.B |
| Adjust L654 so that the picture covers the whole screen horizontally and the battlements are hidden. | L654 | CRT screen | TV controls: Normal |
Circular
pattern |
Horizontal width | 4.A |
|
In case the picture is shifted up or down more than of
3mm. from screen centre, resistor R713 or R712 respectively should be cut. Readjust vertical size if necessary. |
R712
R713 |
CRT screen
North Orientation |
TV controls: Normal |
Circular
pattern |
Vertical centre | 3.C |
| Adjust VR701 to achieve equal length for the upper and lower radius of the circle in vertical direction. | VR701 | CRT screen | TV controls: Normal |
Circular
pattern |
Vertical linearity | 3.B |
| Adjust VR702 to make the picture cover the whole screen vertically and to get the battlements hidden | VR702 | CRT screen | TV controls: Normal |
Circular
pattern |
Vertical size | 3.A |
|
Adjust VR200 to obtain a voltage of
8V ± 0.2V. |
VR200 |
AGC
5 pin TU250 |
Level of aerial signal
60,0 dBμV. (1.0 mVrms.) |
Test pattern
Band III Channel 10 |
AGC | 2.B |
|
Adjust L201 to obtain a voltage of 3,5V. ±0,2V.
The aerial should be disconnected so that it does not interfere with the applied IF signal |
L201 |
AFC_OUT
R111 |
Level of apply IF signal (38,9MHz) of
80 to 250 mVrms on 75Ω in synchronise. |
IF Signal
38,9MHz into IF pin TU250 |
IF Detector
AFC |
2.A |
| Adjust VR800 to obtain: +118V. ±0.5V | VR800 |
B1
Cathode D-850 |
Picture TV: Normal Sound: Volume to minimum |
Circular
pattern |
B1 Power
supply |
د _ |
| SPECIAL FEATURES | ADJUSTMENT |
TEST
POINT |
CONDITIONS | SIGNAL | ADJUSTMENT |
ADJUST
ORDER |
| SPECIAL FEATURES Adjust VR800 to obtain: +118V. ±0.5V Adjust L201 to obtain a voltage of 3,5V. ±0,2V. ● The aerial should be disconnected so that it does not interfere with the applied IF signal Adjust VR200 to obtain a voltage of 8V ± 0.2V. Adjust VR702 to make the picture cover the whole screen vertically and to get the battlements hidden Adjust VR701 to achieve equal length for the upper and lower radius of the circle in vertical direction. In case the picture is shifted up or down more than of 3mm. from screen centre, resistor R713 or R712 respectively should be cut. Readjust vertical size if necessary. Adjust L654 so that the picture covers the whole screen horizontally and the battlements are hidden. Adjust VR600 to centre the picture in horizontal direction. Readjust horizontal width if necessary. Turn the potentiometers completely anticlockwise (seen from solder side) Set the G2 voltage for one colour to be just visible. Adjust the potentiometers conducting, in order to obtain a tenuous line without colour tone. UNhite) The potentiometers must be adjusted in order R503/R504 Adjust to align the OSD vertical bar with the picture of screen. Adjust to align the OSD vertical bar with the picture |
ADJUSTMENT
SPECIAL FEATURES
VR800
Adjust VR800 to obtain: +118V. ±0.5V
L201
Adjust L201 to obtain a voltage of 3,5V. ±0,2V. ●
The aerial should be disconnected so that it does not interfere with the applied IF signal VR700 Adjust VR702 to make the picture cover the whole screen vertically and to get the battements hidden VR701 Adjust VR701 to achieve equal length for the upper and lower radius of the circle in vertical direction. R713 In case the picture cover the whole screen vertically and to get the battements hidden VR600 Adjust VR600 to centre the picture covers the whole screen horizontally and the battements are hidden. VR503 Turn the potentiometers completely anticlockwise (seen vR504 VR505 Set the G2 voltage for one colour to be just visible. Potentiometer Adjust the potentiometers must be adjusted in order to obtain a acceptable colour tone. In case of doubt, they must an acceptable colour tone. In case of doubt, they must an acceptable colour tone in case of doubt, they must an acceptable to obtain the best possible focusing in the centre + and - VR504 Adjust to align the OSD vertical bar with the picture centre. |
TEST
POINT ADJUSTMENT SPECIAL FEATURES B1 Cathode D-850 VR800 Adjust VR800 to obtain: +118V. ±0.5V AFC_OUT L201 Adjust L201 to obtain a voltage of 3.5V. ±0.2V. ● The aerial should be disconnected so that it does not inferfere with the applied IF signal AGC VR200 Adjust VR200 to obtain a voltage of spin TU250 VR200 CRT screen VR701 Adjust VR702 to make the picture cover the whole screen vertically and to get the battements hidden CRT screen R712 Smith the applied IF signal North R713 Smith for the upper and Adjust VR701 to achieve equal length for the upper and increasary. CRT screen VR503 Turn the picture is shifted up or down more than of screen vertical size if necessary. CRT screen VR503 Turn the potentiometers completely anticlockwise (seen vR505 CRT screen VR503 Turn the potentiometers corresponding to those acatoder side) VR504 the optentiometers must be adjusted in order to obtain a vR502 The potentiometers nust be adjusted in order to obtain an acceptable colour tone. (Mhile) CRT screen VR502 Adjust to adin the best possible focusing in the centre vR502 Ext the G2 voltage for one colour to be just visible. CRT screen |
CONDITIONS
TEST
OWN ADJUSTMENT SPECIAL FEATURES Picture TV: Normal 0 B1 Sound: 'Volume to minimum allow 250 m/ms on 7521 in synchronies. B1 Cathode D-850 VR800 Adjust VR800 to obtain: +118V. ±0.5V Adjust VR800 to obtain: +118V. ±0.5V Level of apply Feignal (38,0MHz) of 80,0 dB,W. (1.0 m/ms.) Fpi TU250 L201 The aerial should be disconnected so that it does not synchronies. Level of aerial signal 60,0 dB,W. (1.0 m/ms.) 5 pin TU250 VR200 Adjust VR701 to obtain a voltage of R111 Adjust VR702 to make the picture cover the whole synchronies. TV controls: Normal 0 CRT screen North VR701 Adjust VR701 to achieve adjue and to get the batternents hidden recessary. TV controls: Normal 0 CRT screen North R712 North In case the picture is shift or covers the whole recessary. TV controls: Normal 0 CRT screen Sightness controls: Adjust 0 CRT screen VR503 Turn the polentioneters completely anticlockwise (seen horizontally and the picture is online(s and hidden.) TV controls: Normal 0 CRT screen Service Line 9 CRT screen VR503 L201 Bightness controls: Adjust 0 CRT screen Service Line 9 VR503 Turn the polentioneters corresponding to those from solder side) Colour to minimum acroutrols: normal 0 |
SIGNAL
CONDITIONS
TEST
Point ALUSTMENT SPECIAL FEATURES Circular IF Signal Signal parterin For U250 Picture TV: Normal ● Sound: Values to minimum Sound: Values to minimum Sound: Values to minimum Sound: Values to minimum Fignal (350 mV/ms on 750 mV/ms on partering values on 700 mV/ms on 750 mV/ms on 750 mV/ms on partering values on 700 mV/ms on 750 mV/ms on partering values on 700 mV/ms on 750 mV/ms on 750 mV/ms on partering values on 700 mV/ms on 750 mV/ms on partering values on 700 mV/ms on 750 mV/ms on partering values on 700 mV/ms on 750 mV/ms on partering values on 700 mV/ms on partering values on 700 mV/ms on 750 mV/ms on 771 more finan of partering values on 710 mV/ms on 750 mV/ms on 750 mV/ms on 771 more finan of partering values on 710 mV/ms on 750 mV/ms on 771 more finan of partering values on 710 mV/ms on 750 mV/ms on 771 mV/ms on 750 mV/ms on 771 more finan of partering values on 710 mV/ms on 750 mV/ms on 771 more finan of partering values on 710 mV/ms on 750 mV/ms on 750 mV/ms on 771 more finan of partering values on more finan of partering values on more finan of partering values on more finan of partering values on on the partering values on on the partering values on the partering values on the partering values on the partering values on the partering values on the partering valu |
ADJUSTNIENT
SIGNAL
CONDITIONS
TEST
PONT ADJUSTNIENT SPECIAL FEATURES B1 Power supply Entrular Pattern TV: Normal © B1 Source B1 Normal © SPECIAL FEATURES B1 Power supply Entrular Pattern Level of apply Figinal (3, 3, MHz) of Synchronize. AFC OUT AFC OUT Adjust I/R800 to obtain: +118V. ±0.5V AFC Bard nit B1 200 mVms on 75.0 in M/ms on 75.0 in Synchronize. AFC OUT Adjust I/201 to obtain a voltage of 3,5V. ±0.2V Interesting a should be disconrected so that to does not interfere with the avoitage of 3,5V. ±0.2V. AFC OUT Affect Affect NTC Adjust I/200 to obtain a voltage of 3,5V. ±0.2V. Interfere with the avoitage of 3,5V. ±0.2V. Interfere with the avoitage of 3,5V. ±0.2V. Interfere with the avoitage of 3,5V. ±0.2V. Interfere with the avoitage of 3,5V. ±0.2V. Interfere with the avoitage of 3,5V. ±0.2V. Interfere with the avoitage of 3,5V. ±0.2V. Interfere with the avoitage of 3,5V. ±0.2V. Interfere with the avoitage of 3,5V. ±0.2V. Interfere with the avoitage of 3,5V. ±0.2V. Interfere with the avoitage of 3,5V. ±0.2V. Interfere with the avoitage of 3,5V. ±0.2V. Interfere with the avoitage of 3,5V. ±0.2V. Interfere with the avoitage of 3,5V. ±0.2V. Interfere with the avoitage of 3,5V. ±0.2V. Interfere with the avoitage of |
Nº5C (Cut-off). Pactory picture control normal has the following OSD positions: Brightness: 32 (Push key "+" 32 times starting at minimum position.) Contrast: 57
Colour: 26
The service line is obtained by connecting a resistor of 100 Ω from the test point (R718-C713) to ground. If it is shorted to ground directly, the TV set might pass to Stand-by (due to actuation of the deflection circuit protection).
There can be found 2 positions of the L201 core for which the voltage in R211 is of 3,5V, but the only correct position is that in which that the voltage goes up as the core is introduced in the body of de L201, and the picture is acceptable.
Adjust to brightness. Position 34 (Push key "+" 34 times starting at minimum position.)
Page 8
Page 9
13.- CHASSIS ELECTRICAL PARTS LIST
| Ref. No. | Part No. | Description |
|---|---|---|
| YG 5 * | 0080112113 | Copper Side Shield IF |
| YG 6 ¥ | 0080112022 | Component Side Shield IF |
| 0360306708 | S 2055 N | |
| 0050 | 0300300700 | LA 7832 |
| 0300706101 | ||
| YR10 | 0200224517 | Heatsink Z Deflection |
| YR10A | 0640705117 | Eyelet 2,5-3 |
| YR11 | 0010106300 | Spring CLIP 56379 |
| YR12 | 0970200804 | Silicon Grease YG6260 |
| Assy PE | ||
| Q800 | 0360310809 | MOS 2SK 2750 600V/3,5A |
| YR50 | 0200224129 | Heatsink L 54,6X16 |
| YR50A | 0640705117 | Eyelet 2,5-3 |
| YR51 | 0010110401 | Spring CLIP 56363 |
| VP56 | 0970200804 | Silicon Grease YG6260 |
Page 10
| Ref. No. | Part No. | Description | - في | |
|---|---|---|---|---|
| PCB SOCK | ET TRC | |||
| CONNECTO | RS | |||
| CON FG | 0330144106 | Ribbon Wire Holder 3 P. | ||
| CON FI | 0330144304 | Ribbon Wire Holder 5 P. | ||
| CON.FG | 0160065223 | Polarized Band, Gray 3P. 400+6+6 | ||
| CON FI | 0160231205 | Polarized Band Gray 5P 550+6+6 | ||
| CON.FK | 0640202610 | Earth Wire 270 mm. | ||
| , | CAPACITOR | 25 | ||
| C501 | 0240131516 | Ceramic 470 pF. 2% 100V. | ||
| C502 | 0240131516 | Ceramic 470 pF. 2% 100V. | ||
| C503 | 0240131516 | Ceramic 470 pF. 2% 100V. | ||
| C504 | 0240590901 | Ceramic 2200pF +80-20% 2KV. | ||
| C505 | 0250283868 | Electrolytic 4,7 µF. 250V. | ||
| C540 | 0250461290 | Electrolytic 100 µF. 16V | ||
| DIODES | 0260420904 | 111 41 40 | ||
| D541 | 0300130601 | IN 4140 | ||
| 0750150328 | 21" EC-4A Sockat PCB | |||
| 1 | 0750150526 | 21 EC-4A SOCKELFCB | ||
| TRANSISTO | RS | |||
| Q501 | 0360331029 | JC 558 B | ||
| Q502 | 0360162408 | BF 869 | ||
| Q503 | 0360162408 | BF 869 | ||
| Q504 | 0360162408 | BF 869 | ||
| Q540 | 0360331029 | JC 558 B | ||
| RESISTORS | 0700722702 | |||
| R501 | 0790733703 | Carbon 300 02 5% 1/4W. | ||
| R502 | 0790140401 | Carbon 560 O 5% 1/6W | ||
| R503 | 0790135909 | Carbon 470 O 5% 1/6W | ||
| R505 | 0790147102 | Carbon 4 7 KO 5% 1/4W | ||
| R506 | 0790131908 | Carbon 220 Q 5% 1/6W | ||
| R507 | 0790577175 | Metal Oxide 12 KΩ 5% 2W. | ||
| R508 | 0790131908 | Carbon 220 Ω 5% 1/6W. | ||
| R509 | 0790577175 | Metal Oxide 12 KΩ 5% 2W. | ||
| R510 | 0790131908 | Carbon 220 Ω 5% 1/6W. | ||
| R511 | 0790577175 | Metal Oxide 12 KΩ 5% 2W. | ||
| R512 | 0790123400 | Carbon 47 Ω 5% 1/6W. | ||
| R513 _ | 0790123400 | Carbon 47 Ω 5% 1/6W. | ||
| R514 | 0790123400 | Carbon 47 Ω 5% 1/6W. | ||
| R515 | 0790036917 | Carbon 1,5 KΩ 5% 1/2W. | ||
| R516 | 0790147102 | Carbon 4,7 K0 5% 1/4W. | ||
|
R517
P518 |
0790030917 | Carbon 4 7 KO 5% 1/2W | ||
| R519 | 0790036917 | Carbon 1 5 KO 5% 1/2W | ||
| R520 | 0790147102 | Carbon 4.7 KΩ 5% 1/4W. | ||
| R521 | 0790134001 | Carbon 390 Ω 5% 1/6W | ||
| R522 P | 0790134001 | Carbon 390 Ω 5% 1/6W | ||
| R522 V | 0790733901 | Carbon 360 Ω 5% 1/6W | ||
| R523 | 0790036917 | Carbon 1,5 KΩ 5% 1/2W. | ||
| R524 | 0790175707 | Carbon 1 MΩ 5% 1/6W. | ||
| R527 P | 0790134001 | Carbon 390 Ω 5% 1/6W | ||
| R527 V | 0790733901 | Carbon 360 Ω 5% 1/6W | ||
| R528 P | 0790733901 | Carbon 360 Ω 5% 1/6W. | ||
| R528 V | 0790134001 | Carbon 390 12 5% 1/6W. | ||
| ł | R040 | 0790145106 | Carbon 3,3 K2 5% 1/6W | |
| R541 | 0/30131300 | |||
| RESISTORS | ||||
| VR501 | 0770511152 | VR 220 Ω | ||
| VR502 | 0770511152 | VR 220 Ω | ||
| VR503 | 0770511459 | VR 10 KΩ | ||
| VR504 | 0770511459 | VR 10 KΩ | ||
| VR505 | 0770511459 | VR 10 KΩ | ||
| SUCKET | 0330159906 | UKI SOCKEI | ||
| Ref. No. | Part No. | Description |
|---|---|---|
| 0000411100 | ||
|
CF200
CF201 |
0090411109 |
Ceramic Filter 5,5 MH.
Ceramic Filter 5.5 MHz. |
| CONNECTO | RS | - |
| CN FB | 0330191701 | 2P. Socket |
| CN FC | 0330115106 | 2P. Socket X RTM 1/6/8 |
| CN FCA | 0640850210 | Eyelet 1,6-3 |
| CN FE | 0330115106 | 2P. Socket X RTM 1/6/8 |
| CN FEA | 0640850210 | Eyelet 1,6-3 |
| CN FF2 | 0330190000 | 2 P. Socket |
| CN FG | 0330144106 | Ribbon Wire Holder 3 P |
| CN FI | 0330144304 | Ribbon Wire Holder 5 P. |
| CAPACITOR | s | |
| C100 | 0250320793 | Electrolytic 10 µF. 16V. |
| 0240143214 | Ceramic 10 nF. +80-20% 63V. | |
| C102 | 0240143214 | Electrolytic 6.8 µE 50V |
| C104 | 0240123711 | Ceramic 100 pF 2% 100V |
| C105 | 0240111716 | Ceramic 10 pF. 2% 100V. |
| C106 | 0240119917 | Ceramic 47 pF. 2% 100V. |
| C107 | 0270281124 | Polyester 33 nF. 10% 100V. |
| C108 | 0270281124 | Polyester 33 nF. 10% 100V. |
| C109 | 02/0220/26 | Polyester 10 nF. 10% 250V. |
| C111 | 0240119917 | Ceramic 47 pF. 2% 100V. |
| C112 | 0270400989 | Polvester 330 nF, 10% 63V. |
| C114 | 0240123711 | Ceramic 100 pF. 2% 100V. |
| C115 | 0250220456 | Electrolytic 1 µF. 100V. |
| C116 | 0250220456 | Electrolytic 1 µF. 100V. |
| C118 | 0250220456 | Electrolytic 1 µF. 100V. |
| C119 | 0250320793 | Electrolytic 10 µF. 16V. |
| C120 | 0250220456 | Electrolytic 1 µF. 100V. |
| C121 | 0250220456 | Electrolytic 1 µF. 100V. |
| C126 | 0270381031 | Polyester 220 nF. 10% 63V. |
| C170 | 0250280864 | Electrolytic 4.7 µF. 25V. |
| C175 | 0250410891 | Electrolytic 47 µF. 16V. |
| C181 | 0240115618 | Ceramic 22 pF. 2% 100V. |
| C182 | 0240117218 | Ceramic 33 pF. 2% 100V. |
| C190 | 0240143214 | Ceramic 10 nF. +80-20% 63V |
| C191 | 0270381031 | Polyester 220 nF. 10% 63V. |
| C193 | 0270341431 | Polyester 100 nF. 10% 63V. |
| C200 | 0240111716 | Ceramic 10 pF. 2% 100V. |
| C201 | 0250220456 | Electrolytic 10 µF 16V |
| C203 | 0240551242 | Ceramic 1000 pF. +80-20% 50V. |
| C204 | 0250320793 | Electrolytic 10 µF. 16V. |
| C206 | 0270341431 | Polyester 100 nF. 10% 63V. |
|
C207
C230 |
0200320793 |
Electrolytic 10 µF, 16V.
Ceramic 68 pE 2% 100V |
| C232 | 0240143214 | Ceramic 10 nF. +80-20% 63V |
| C250 | 0250461290 | Electrolytic 100 µF. 16V |
| C256 | 0250360492 | Electrolytic 22 µF. 16V. |
| C301 | 0240144410 | Ceramic 22 nF. +80-20% 63V. |
| C302 | 02/0341431 | Ceramic 470 pE 10% 63V. |
| C304 | 0250220456 | Electrolytic 1 µF. 100V. |
| C305 | 0250410891 | Electrolytic 47 µF. 16V. |
| C306 | 0250220456 | Electrolytic 1 µF. 100V. |
| C307 | 0250240496 | Electrolytic 2,2 µF. 63V. |
| C312 | 0240561100 | Ceramic 1000 pF. +80-20% 63V. |
| C318 | 0240142414 | Ceramic 4700 pF 10% 100\/ |
| C320 | 0250320793 | Electrolytic 10 µF. 16V. |
| C323 | 0270341431 | Polyester 100 nF. 10% 63V. |
| C324 | 0250570462 | Electrolytic 1000 µF. 25V. |
|
C325
C327 |
0200030425 |
Electrolytic 4/U µF. 16V.
Polyester 220 pE 10% 62V |
| C400 | 0240144410 | Ceramic 22 nF. +80-20% 63V |
Page 11
| Ref. No. | Part No. | Description | er. |
|---|---|---|---|
| C401 | 0250500667 | Electrolytic 220 uF. 16V. | |
| C402 | 0270341431 | Polyester 100 nF. 10% 63V. | |
| C403 | 0270341431 | Polyester 100 nF. 10% 63V. | |
| C404 | 0250240496 | Electrolytic 2,2 µF. 63V. | |
| C405 | 0240114611 |
Ceramic 18 pF. 2% 100V.
Polyester 4700 pE 10% 250V |
|
| C407 | 0270180023 | Polyester 100 pF. 10% 63V. | |
| C409 | 0240143214 | Ceramic 10 nF. +80-20% 63V. | |
| C410 | 0240143214 | Ceramic 10 nF. +80-20% 63V. | |
| C411 | 0240143214 | Ceramic 10 nF. +80-20% 63V. | |
| C412 | 0240141614 | Ceramic 3900 pF.10% 100V. | |
|
C413
C414 |
0270341431 | Polyester 100 nF 10% 63V. | |
| C415 | 0270341431 | Polyester 100 nF. 10% 63V. | |
| C416 | 0240551242 | Ceramic 1000 pF. +80-20% 50V. | |
| C417 | 0240143214 | Ceramic 10 nF. +80-20% 63V. | |
| C418 | 0240143214 | Ceramic 10 nF. +80-20% 63V. | |
|
C419
C420 |
0240143214 | Polyester 100 nF 10% 63V | |
| C422 | 0250360492 | Electrolytic 22 µF. 16V. | |
| C424 * | 0240123711 | Ceramic 100 pF. 2% 100V. | |
| C425 | 0250530425 | Electrolytic 470 µF. 16V. | |
| C427 * | 0270341431 | Polyester 100 nF. 10% 63V. | |
| C430 | 0250320793 | Electrolytic 47 µF 16V | |
| C601 | 0240142414 | Ceramic 4700 pF. 10% 100V | |
| C602 | 0250222841 | Electrolytic 1µF. 50V. | |
| C603 | 0240139618 | Ceramic 2200 pF.10% 100V. | |
| C604 | 0270341431 | Polyester 100 nF. 10% 63V. | |
| C607 | 02/03/0566 | Polypropylene 10 nF 5% 1 5KV. | |
| C651 V | 0260217120 | Polypropylene 9100 pF. 5% 1,5KV. | |
| C651A | 0640850210 | Eyelet 1,6-3 | |
| C654 | 0270450232 | Polyester 820 nF. 5% 250V. | |
| C655 | 0240133355 | Ceramic 680 pF. 10% 1KV. | |
| C657 | 0270341431 | Polyester 2200 pF 10% 63V. | |
| C661 P | 0260420278 | Polypropylene 470 nF. 5% 400V. | |
| C661 V | 0260400270 | Polypropylene 330 nF. 5% 400V. | |
| C661A | 0640850210 | Eyelet 1,6-3 | |
| C662 | 0250220456 | Electrolytic 1 µF. 100V. | |
| C665 | 0240133355 | Polvester 100 nF. 10% 250V. | |
| C668 | 0250240496 | Electrolytic 2,2 µF. 63V. | |
| C671 | 0250248267 | Electrolytic 2,2 µF. 160V. | |
| C672 | 0240132035 | Ceramic. 470 pF. 10% 1KV. | |
| C701 | 0250501564 | Electrolytic 2200 µF. 25V. | |
| C703 | 0270341431 | Polyester 100 nF. 10% 63V. | |
| C704 | 0270100522 | Polyester 1000 pF. 10% 400V. | |
| C705 | 0270220726 | Polyester 10 nF. 10% 250V. | |
| C706 | 0250600913 | Electrolytic 2200 µF. 16V. | |
| C710 | 0270381031 | Polyester 220 nF. 10% 63V. | |
| C711 | 0240119917 | Ceramic 47 pF. 2% 100V. | |
| C713 | 0270342603 | Policarb. 100 nF. 5% 63V. | |
| C714 | 0270220726 | Polyester 10 nF. 10% 250V. | |
| 0270401508 | Polyester 330 nF. 20% 2/5V.AC | ||
| C805 | 0240134767 | Ceramic 1000 pF. ±20% 1KV. | |
| C807 | 0240134767 | Ceramic 1000 pF. ±20% 1KV. | |
| C808 | 0240134767 | Ceramic 1000 pF. ±20% 1KV. | |
| C809 *A | 0240136135 | Ceramic 1000 pF. 20% 4KV | |
| C810 | 0250464708 | Electrolytic 100 µF. 400V. | |
| C810A | 0040705117 |
Eyelet 2,5-5
Ceramic 1000 pF +20% 1KV |
|
| C812 | 0270100522 | Polyester 1000 pF. 10% 400V. | |
| C813 | 0240390914 | Ceramic 47 pF. 5% 1KV. | |
| C814 | 0270281231 | Polyester 33 nF. 10% 400V. | |
| C815 | 0250412897 | ||
| C818 | 0240561100 | Ceramic 1000 pF. +80-20% 63V. | |
| C820 | 0240430306 | Ceramic 100 pF. 2% 100V. | |
| C821 * ∆ | 0240136135 | Ceramic 1000 pF. 20% 4KV | |
| C822 | 0270341431 | Polyester 100 nF. 10% 63V. |
| Ref. No. | Part No. | Description |
|---|---|---|
| C850 | 0240430710 | Ceramic 100 pE 5% 1KV |
| C851 | 0250132776 | Electrolytic, 100 µF, 200V. |
| C854 | 0250531944 | Electrolytic 470µF. 25V. |
| C856 | 0250531944 | Electrolytic 470µF. 25V. |
| C857 | 0250320793 | Electrolytic 10 µF. 16V. |
| C858 | 0250320793 | Electrolytic 10 µF. 16V. |
| C859 | 0250220464 | Electrolytic 1 µF. 100V. |
| C900 | 0240123711 | Ceramic 100 pF 2% 100V |
| C902 | 0250320793 | Electrolytic 10 µF. 16V. |
| C904 | 0250320793 | Electrolytic 10 µF. 16V. |
| C906 | 0250320793 | Electrolytic 10 µF. 16V. |
| C912 * | 0240131417 | Ceramic 470 pF. 10% 100V. |
| 0240131417 | Ceramic 470 pF. 10% 100V. | |
| C917 | 0240131417 | Ceramic 470 pF. 10% 100V. |
| C918 | 0250320793 | Electrolytic 10 µF. 16V. |
| C919 | 0250320793 | Electrolytic 10 µF. 16V. |
| C922 | 0240143214 | Ceramic 10 nF. +80-20% 63V. |
| C942 | 0250320793 | Electrolytic 10 µF. 16V. |
| DIODES | ||
| D100 | 0360126304 | RED 3mm. |
| D101 | 0360130801 | 1N 4148 |
| D102 | 0360130801 | 1N 4148 |
| D103 | 0360130801 |
1N 4148
1N 4148 |
| D120 | 0470040007 | Jumper Lead 0.6 mm. |
| D251 | 0360135107 | Zener BZX79C8V2 |
| D252 | 0360135107 | Zener BZX79C8V2 |
| D253 | 0360135107 | Zener BZX79C8V2 |
| D302 | 0360130801 |
1N 4148
Zonor BZX79C5V/1 |
| D400 | 0360130801 | 1N 4148 |
| D601 | 0360103204 | Zener BZX79C5V1 |
| D653 | 0360377006 | ERB44-04 |
| D654 | 0360376909 | ERB44-02 |
| D655 | 0360130801 | 1N 4148 |
| D657 | 0360135107 | 1N 4007 RI |
| D659 | 0360130801 | 1N 4148 |
| D660 | 0360005409 | Zener BZX79C24 |
| D661 P | 0360135107 | Zener BZX79C8V2 |
| D661 V | 0360103204 | Zener BZX/9C5V1 |
| D663 | 0360377006 | ERB44-04 |
| D664 | 0360107106 | Zener BZX79C15 |
| D670 | 0360130801 | 1N 4148 |
| D701 | 0360130629 | 1N 4007 RL |
| L1/02 | 0360130801 | 1N 4148 |
| D703 | 0470040007 | Jumper Lead 0.6 mm. |
| D800 | 0360130629 | 1N 4007 RL |
| D801 | 0360130629 | 1N 4007 RL |
| D802 | 0360130629 | 1N 4007 RL |
| D803 | 0360376800 | |
| D805 | 0360376909 | ERB44-02 |
| D806 | 0360130801 | 1N 4148 |
| D850 | 0360376404 | ERB44-06 |
| D851 | 0360376701 | Schottky RK 19 V1 |
| D853 | 0360130819 | 1N 4148 |
| D854 | 0360130819 | 1N 4148 |
| D855 | 0360103204 | Zener BZX79C5V1 |
| D859 | 0360005508 | Zener BZX79C9V1 |
| D900 | 0360004709 | Zener BZX79C12 |
| D902 | 0360004709 |
Zener BZX79012
Zener BZX79012 |
| D904 | 0360004709 | Zener BZX79C12 |
| D909 | 0360004709 | Zener BZX79C12 |
| D911 | 0360004709 | Zener BZX79C12 |
| 0760100704 | Fuse Terminal Taned | |
| 0/00/00/01 | i use i enninar rapeu |
Page 12
| Ref. No. | Part No. | Description |
|---|---|---|
| F800 🛆 | 0330161902 | Fuse T 2 A./250V. TIME-LAG |
| INTEGRA | TED CIRCUITS | |
| IC100 | 0360471916 | SDA 5251-A004 |
| IC125 | 0360478101 | AT24C02-10PC |
| 10190 | 0360706014 | HZ 133-02 RE |
| IC400 | 0360513444 | TDA 8361 N5 |
| IC401 | 0360142202 | U 3661 M |
| IC701 | 0360708101 | LA 7832 |
| IC800 | 0360467203 | MC44603P |
| 1C900 | 0360706600 | LA 7016 |
| IP125 | 0800105603 | EC-4A BM 21" NVM DATA |
| 0000310220 | Peaking Coll 4.7 uH 40% | |
| L101 | 062000519229 | Pipe Core 3.5X4.5 |
| L105 | 0090319864 | Peaking Coil 6,8 µH 5% |
| L200 | 0090315029 | Peaking Coil 10 µH. 10% |
| L201 | 0090502303 | Coil 38,9 MH.C/COND.100pF |
| L202 | 0090315029 | Peaking Coil 10 µH. 10% |
| L210 | 0090304627 | Peaking Coil 1 µH. 10% |
| L250 | 0090315763 | Peaking Coll 100 µH 10% |
| L303 | 0790528400 | Fuse 2.2 O 5% 0 75W |
| L304 | 0470040007 | Jumper Lead 0.6 mm. |
| L400 | 0090319260 | Peaking Coil 4,7 µH. 10% |
| L402 * | 0620005504 | Pipe Core 4330 030 38741 EMB. |
| L403 * | 0090319260 | Peaking Coil 4,7 µH. 10% |
| L404 * | 0090319260 | Peaking Coil 4,7 µH. 10% |
| L405 * | 0090319260 | Peaking Coil 4,7 µH. 10% |
| 0090315060 | Linearity Coll | H11 I70SH-T10 | |
| L652 V | 0090206707 | Linearity Coil LH11J105SH-T10 |
| L652A | 0640850210 | Eyelet 1,6-3 |
| L654 | 0090310806 | Adjustable Width Coil 27/130 µH. |
| L654A | 0640850210 | Eyelet 1,6-3 |
| L801 \star 🛆 | 0090412602 | Mains Filter 2X18 MH. 250 VAC. 0,5A |
| L801A | 0640850210 | Eyelet 1,6-3 |
| 0090304627 | Pipe Core 3 5X4 5 | |
| L850 | 0620005116 | Pipe Core 3.5X4.5 |
| L851 | 0620005116 | Pipe Core 3,5X4,5 |
| L852 | 0620005116 | Pipe Core 3,5X4,5 |
| L901 | 0790036305 | Carbon 2,2 KΩ 5% 1/4W. |
| L902 * | 0790036305 | Carbon 2,2 KΩ 5% 1/4W. |
| L903 ¥ | 0790036305 | Carbon 2,2 KΩ 5% 1/4W. |
| 0090315029 | ||
| PCB11 */ | 0750150229 | 21" EC-4A MAIN PCB |
| PTC800 | 0810101212 | DUAL PTC 18 Ω ±25% |
| 1 KANSIST | 0360330024 | IC 548 B |
| Q105 | 0360189112 | PH2369 |
| Q106 | 0360330021 | JC 548 B |
| Q107 | 0360330021 | JC 548 B |
| Q111 | 0360330021 | JC 548 B |
| Q120 | 0360330021 | JC 548 B |
|
Q121
0200 |
0360330021 | |
| Q200 | 0300330021 | JC 558 B |
| Q251 | 0360331029 | JC 558 B |
| Q252 | 0360331029 | JC 558 B |
| Q253 | 0360331029 | JC 558 B |
| Q300 | 0360330021 | JC 548 B |
| Q301 | 0360330021 | JC 548 B |
| Q302 | 0360331029 | JC 558 B |
|
Q400
Q401 |
0300331029 | JC 538 B |
| Q430 | 0360330021 | JC 548 B |
| Q431 | 0360331029 | JC 558 B |
| Q600 | 0360169916 | BC 879 Darlington |
| Ref. No. | Part No. | Description |
|---|---|---|
| Q650 | 0360306708 | S 2055 N |
| Q650A | 0640705117 | Eyelet 2,5-3 |
| Q703 | 0360331029 | JC 558 B |
| 0850 | 0360310809 | MOS 2SK2750 600V/3,5A |
| Q851 | 0360306104 | 2SB 764 F |
| Q852 | 0360330021 | JC 548 B |
| Q853 | 0360331029 | JC 558 B |
| Q854 | 0360331029 | JC 558 B |
| Q855 | 0360306203 | 2SD 863 E |
| Q856 | 0360331029 | JC 558 B |
| Q859 | 0360331029 | JC 558 B |
| Q860 | 0360330021 | JC 548 B |
| Q866 | 0360330021 | JC 548 B |
| Q900 | 0360330021 | JC 548 B |
| Q901 | 0360330021 | JC 548 B |
| RI100 | 0600122204 | Infrared Receiver SBX8030-F |
| RESISTORS | ||
| R100 | 0790133607 | Carbon 330 Ω 5% 1/6W. |
| R101 | 0790352520 | Metal Film 4,02 KΩ 1% 0,4W. |
| R102 | 0790126700 | Carbon 100 Ω 5% 1/6W. |
| R103 | 0790126700 | Carbon 100 Ω 5% 1/6W. |
| R105 | 0790146401 | Carbon 3.9 KO 5% 1/6W |
| R106 | 0790143606 | Carbon 2.2 KO 5% 1/6W |
| R107 | 0790153605 | Carbon 15 KΩ 5% 1/6W |
| R108 | 0790578306 | Metal Film 15 KΩ 1% 0,4W. |
| R109 | 0790588529 | Metal Film 100 KΩ 1% 0,4W. |
| R111 | 0790135701 | Carbon 470 Ω 5% 1/6W. |
| R112 | 0790155600 | Carbon 22 KΩ 5% 1/6W. |
|
R113
P114 |
0/90126/00 | Carbon 100 Ω 5% 1/6W. |
| R114 | 0790151500 | Carbon 10 KO 5% 1/6W |
| R116 | 0790150601 | Carbon 8,2 KΩ 5% 1/6W. |
| R117 | 0790149405 | Carbon 6,8 KΩ 5% 1/6W. |
| R118 | 0790149405 | Carbon 6,8 KΩ 5% 1/6W. |
| R119 | 0790126700 | Carbon 100 Ω 5% 1/6W. |
| R120 | 0790138804 | Carbon 1 KΩ 5% 1/6W. |
| R124 | 0790120700 | Carbon 100 Ω 5% 1/6W. |
| R125 | 0790147607 | Carbon 4.7 KO 5% 1/6W/ |
| R126 | 0790147607 | Carbon 4.7 KΩ 5% 1/6W. |
| R127 | 0790151500 | Carbon 10 KΩ 5% 1/6W. |
| R128 | 0790162309 | Carbon 82 KΩ 5% 1/6W. |
| R129 | 0790174007 | Carbon 750 KΩ 5% 1/6W. |
| R130 | 0790143606 | Carbon 2,2 KΩ 5% 1/6W. |
| R131 | 0700165202 | |
| R133 | 0790155600 | Carbon 22 KO 5% 1/6W |
| R135 | 0790160501 | Carbon 56 KΩ 5% 1/6W. |
| R136 | 0790755003 | Carbon 20 KΩ 5% 1/6W. |
| R137 | 0790758007 | Carbon 36 KΩ 5% 1/6W. |
| R139 | 0790769103 | Carbon 330 KΩ 5% 1/6W. |
| R140 | 0790180509 | Carbon 2,2 MΩ 5% 1/4W. |
| R141 | 0790178107 | Carbon 1,5 MΩ 5% 1/4W. |
| R142 | 0790155600 | |
| R144 | 0790157408 | Carbon 33 KO 5% 1/6W |
| R145 | 0790126700 | Carbon 100 Ω 5% 1/6W. |
| R146 | 0790364129 | Metal Film 22,1 KΩ 1% 0,4W. |
| R147 | 0790750004 | Carbon 7,5 KΩ 5% 1/6W. |
| R148 | 0790143606 | Carbon 2,2 KΩ 5% 1/6W. |
| R149 | 0790151708 | Carbon 12 KΩ 5% 1/6W. |
| K150 | 0790143606 | Carbon 2,2 KΩ 5% 1/6W. |
| R151 | 0700148605 | |
| R153 | 0790148605 | Carbon 5.6 KO 5% 1/6W |
| R154 | 0790153605 | Carbon 15 KΩ 5% 1/6W |
| R155 | 0790138804 | Carbon 1 KΩ 5% 1/6W. |
| R156 | 0790142509 | Carbon 1,8 KΩ 5% 1/6W. |
Page 13
| Ref. No. | Part No. | Description |
|---|---|---|
| R157 | 0790151500 | Carbon 10 KΩ 5% 1/6W. |
| R158 | 0790155600 | Carbon 22 KΩ 5% 1/6W. |
| R159 | 0790163000 | Carbon 100 KΩ 5% 1/6W |
|
R160
R161 |
0790756308 | Carbon 27 Q 5% 1/6W. |
| R162 | 0790123400 | Carbon 47 Ω 5% 1/6W. |
| R163 | 0790123400 | Carbon 47 Ω 5% 1/6W. |
| R165 | 0790144505 | Carbon 2,7 KΩ 5% 1/6W. |
| R167 | 0790151500 | Metal Film 5.11 KΩ 1% 0.4W. |
| R168 | 0790159503 | Carbon 47 KΩ 5% 1/6W |
| R169 | 0790151500 | Carbon 10 KΩ 5% 1/6W. |
| R170 | 0790151500 | Carbon 10 KΩ 5% 1/6W. |
|
R175
R177 |
0790123000 | Carbon 10 KΩ 5% 1/6W. |
| R179 | 0790138804 | Carbon 1 KΩ 5% 1/6W. |
| R180 | 0790138804 | Carbon 1 KΩ 5% 1/6W. |
|
R181
P182 |
0790147607 | Carbon 47 KO 5% 1/6W |
| R185 | 0790138804 | Carbon 1 KΩ 5% 1/6W. |
| R186 | 0470040007 | Jumper Lead 0,6 mm. |
| R188 | 0790151500 | Carbon 10 KΩ 5% 1/6W. |
|
R189
R190 |
0790578140 | Metal Oxide 15 KΩ 5% 2W. |
| R191 | 0790153605 | Carbon 15 KΩ 5% 1/6W |
| R200 | 0790149405 | Carbon 6,8 KΩ 5% 1/6W. |
| R201 | 0790155600 | Carbon 22 KΩ 5% 1/6W |
|
R202
R203 |
0790149405 | Carbon 6,8 KΩ 5% 1/6W. |
| R204 | 0790137707 | Carbon 680 Ω 5% 1/6W |
| R205 | 0790138804 | Carbon 1 KΩ 5% 1/6W. |
| R206 | 0790135701 | Carbon 470 02 5% 1/6W. |
| R207 | 0790141600 | Carbon 1,5 KΩ 5% 1/6W. |
| R209 | 0790135701 | Carbon 470 Ω 5% 1/6W. |
| R210 | 0790135909 | Carbon 560 Ω 5% 1/6W. |
|
R212
R217 |
0790135701 | Carbon 270 Ω 5% 1/6W. |
| R218 | 0790135701 | Carbon 470 Ω 5% 1/6W. |
| R235 | 0790137707 | Carbon 680 Ω 5% 1/6W |
| R251 | 0790147607 | Carbon 4,7 KΩ 5% 1/6W |
|
R252
R253 |
0790147607 | Carbon 4,7 KΩ 5% 1/6W. |
| R254 | 0790147607 | Carbon 4,7 KΩ 5% 1/6W. |
| R255 | 0790147607 | Carbon 4,7 KΩ 5% 1/6W. |
|
R256
R262 |
0790147607 | Carbon 5.6 KΩ 5% 1/6W. |
| R300 | 0790159503 | Carbon 47 KΩ 5% 1/6W |
| R301 | 0790159503 | Carbon 47 KΩ 5% 1/6W |
| R302 | 0790168504 | Carbon 270 KΩ 5% 1/6W. |
| R303 | 0790157408 | Carbon 33 KΩ 5% 1/6W. |
| R306 | 0790155600 | Carbon 22 KΩ 5% 1/6W. |
| R307 | 0790151500 | Carbon 10 KΩ 5% 1/6W. |
| R308 | 0790155600 | Carbon 22 Ky 5% 1/6w. |
| R312 | 0790145106 | Carbon 3,3 KΩ 5% 1/6W |
| R316 | 0790148605 | Carbon 5,6 KΩ 5% 1/6W. |
| R317 | 0790111207 |
Carbon 4,7 12 5% 1/4W.
Carbon 180 O 5% 1/6W |
| R320 | 0790151500 | Carbon 10 KΩ 5% 1/6W. |
| R321 | 0790151500 | Carbon 10 KΩ 5% 1/6W. |
| R322 | 0790163000 | Carbon 100 KΩ 5% 1/6W |
| R323 | 0790138804 |
Carbon 1 N2 5% 1/6Ψ.
Carbon 150 Ω 5% 1/6Ψ |
| R400 | 0790163000 | Carbon 100 KΩ 5% 1/6W |
| R401 | 0790151500 | Carbon 10 KΩ 5% 1/6W. |
| R402 | 0790151500 | Carbon 10 KΩ 5% 1/6W. |
| R403 | 0790138804 |
Carbon 1 K2 5% 1/000.
Carbon 6.8 KO 5% 1/6W |
| R408 | 0790153605 | 6 Carbon 15 KΩ 5% 1/6W |
| R409 | 0790131601 | Carbon 220 Ω 5% 1/2W. |
| Ref. No. | Part No. | Description |
|---|---|---|
| R410 | 0790150601 | Carbon 8,2 KΩ 5% 1/6W. |
| R411 | 0470040007 | Jumper Lead 0,6 mm. |
| R412 | 0470040007 | Jumper Lead 0,6 mm. |
| R413 ¥ | 0790126700 | Carbon 100 Ω 5% 1/6W. |
|
R414
R415 |
0790126700 | Carbon 100 Q 5% 1/6W. |
| R417 | 0470040007 | Jumper Lead 0,6 mm. |
| R420 | 0470040007 | Jumper Lead 0,6 mm. |
| R421 | 0470040007 | Jumper Lead 0,6 mm. |
| R422 | 0790026207 | Carbon 560 Ω 5% 1/4W. |
|
R423
P425 |
0790028207 | lumper Lead 0.6 mm |
| R430 | 0790138804 | Carbon 1 KΩ 5% 1/6W. |
| R431 | 0790142509 | Carbon 1,8 KΩ 5% 1/6W. |
| R432 | 0790135909 | Carbon 560 Ω 5% 1/6W. |
| R433 | 0790137202 | Carbon 680 Ω 5% 1/4W. |
|
R600
R601 P |
0790132104 |
Carbon 270 02 5% 1/4w.
Metal Film 0.56 O.5% 0.61W |
| R601 V | 0790523401 | Metal Film 1 Ω 1% 0,6W. |
| R602 | 0790552418 | Metal Film 220 Ω 5% 2W. |
| R603 | 0790151500 | Carbon 10 KΩ 5% 1/6W. |
| R604 | 0790174106 | Carbon 820 KΩ 5% 1/4W. |
| R606 | 0790756308 | Carbon 27 KO 5% 1/6W. |
|
R607
R608 |
0790140401 | Carbon 560 Q 5% 1/6W |
| R611 | 0790539001 | Metal Film 18 Ω 5% 1W. |
| R612 | 0790538813 | Metal Film 15 Ω 5% 1W. |
| R641 P | 0790532402 | Metal Oxide 4,7 Ω 5% 1,5W. |
| R641 V | 0090206608 | Coil 25 µH 10% 1,5A. |
| R650 | 0790161608 | |
| R651 (4) | 0790531701 | Carbon 10 KO 5% 1/6W |
| R655 | 0790155600 | Carbon 22 KΩ 5% 1/6W. |
| R656 | 0780163309 | Wirewound 8,2 Ω 10% 5W. |
| R661 | 0790138804 | Carbon 1 KΩ 5% 1/6W. |
| R662 | 0790027502 | Carbon 1 KΩ 5% 1/4W. |
| R663 | 0790558316 | Metal Film 820 Ω 1% 0,61W. |
| R673 | 0790138804 | Carbon 1 KQ 5% 1/6W. |
| R674 | 0790159503 | Carbon 47 KΩ 5% 1/6W |
| R675 | 0790147607 | Carbon 4,7 KΩ 5% 1/6W. |
| R676 | 0790151708 | Carbon 12 KΩ 5% 1/6W. |
| R677 | 0790159503 | Carbon 47 KΩ 5% 1/6W |
| R679 | 0/905/0/00 | Jumper Lead 0.6 mm. |
| R701 | 0470040007 | Jumper Lead 0,6 mm. |
| R702 | 0790142509 | Carbon 1,8 KΩ 5% 1/6W. |
| R703 | 0790151500 | |
| R704 | 0790756308 | Carbon 27 KΩ 5% 1/6W |
| R706 | 0790526701 | Metal Film 1.5 Ω 1% 0.6W. |
| R707 | 0790151500 | Carbon 10 KΩ 5% 1/6W. |
| R708 | 0790151500 | Carbon 10 KΩ 5% 1/6W. |
| R709 P | 0790036800 | Carbon 1,5 KΩ 5% 1/4W. |
| R709 V | 0700121601 |
Carbon 1,8 KW 5% 1/4W.
Carbon 220 O 5% 1/2W |
| R710 P | 0790551113 | Power Metal Film 180 Ω 5% 1W. |
| R712 | 0790036800 | Carbon 1,5 KΩ 5% 1/4W. |
| R713 | 0790036305 | Carbon 2,2 KΩ 5% 1/4W. |
| R714 | 0470040007 | Jumper Lead 0,6 mm. |
| R715 | 0790123400 | Carbon 47 Ω 5% 1/6W. |
| R717 | 0790103000 | Carbon 3.3 MO 5% 1/4W |
| R718 | 0790604607 | Metal Film 3,3 MΩ 1% 0.6W. |
| R722 | 0790151500 | Carbon 10 KΩ 5% 1/6W. |
| R724 | 0790148605 | 6 Carbon 5,6 KΩ 5% 1/6W. |
| R800 🛆 | 0790185524 | Solid 5,6 MΩ 10% 1/2W. |
| R801 | 0780147815 | 5 Wirewound 3,9 Ω 10% 6W. |
| R802 | 0790125702 | Carbon 75 Ω 5% 1/4W. |
| R804 | 0790588313 | |
| R806 | 0790750004 | Carbon 7,5 KΩ 5% 1/6W. |
| 1 |
Page 14
| Ref. No. | Part No. | Description |
|---|---|---|
| R807 | 0790151500 | Carbon 10 KΩ 5% 1/6W. |
| R808 | 0790175707 | Carbon 1 MΩ 5% 1/6W. |
| R809 | 0790160907 | Carbon 62 KΩ 5% 1/6W. |
| R810 | 0790756308 | Carbon 27 KΩ 5% 1/6W. |
| R812 | 0790523344 | Metal Film 1 0 5% 2W |
| R813 | 0790158307 | Carbon 39 KΩ 5% 1/6W. |
| R814 | 0790583603 | Metal Film 62 KΩ 5% 2W. |
| R816 | 0790184113 | Carbon 4,7 MΩ 5% 1/2W. |
| R818 | 0790123103 | Carbon 47 Ω 5% 1/4W. |
| R819 21 | 0790185524 | Solid 5,6 MΩ 10% 1/2W. |
| R821 | 0790135206 | Carbon 470 O 5% 1/4W |
| R822 | 0790147607 | Carbon 4,7 KΩ 5% 1/6W. |
| R823 | 0790027502 | Carbon 1 KΩ 5% 1/4W. |
| R824 🛆 | 0790513014 | Fuse 0,33 Ω 5% 0,5W. |
| R850 | 0790565923 | Metal Film 2,43 KΩ 1% 0,4 W. |
| R851 | 0790346522 | Metal Film 1,40 KΩ 1% 0,4W. |
| R853 | 0790120700 | Carbon 2 2 KO 5% 1/6W |
| R854 | 0790541312 | Metal OX. RES. 27 Ω 5% 2W. |
| R857 | 0790552418 | Metal Film 220 Ω 5% 2W. |
| R858 | 0790164107 | Carbon 120 KΩ 5% 1/4W. |
| R860 | 0790151500 | Carbon 10 KΩ 5% 1/6W. |
| R861 | 0700454500 | Carbon 1,5 KΩ 5% 1/4W. |
| R863 | 0790151500 |
Carbon 10 K2 5% 1/6vv.
Metal Film 1 91 KO 1% 0 4W |
| R864 | 0790135305 | Carbon 470 Ω 5% 1/2W. |
| R866 | 0790330518 | Metal Film 100 Ω 5% 2W. |
| R867 | 0790144505 | Carbon 2,7 KΩ 5% 1/6W. |
| R868 | 0790151500 | Carbon 10 KΩ 5% 1/6W. |
| R877 | 0790027502 | Carbon 1 KΩ 5% 1/4W. |
| R879 | 0790151500 | Carbon 22 KO 5% 1/6W |
| R903 | 0470040007 | Jumper Lead 0.6 mm. |
| R906 | 0790158109 | Carbon 39 KΩ 5% 1/4W. |
| R907 | 0790756308 | Carbon 27 KΩ 5% 1/6W. |
| R909 🕰 | 0790540900 | Fuse 27 Ω 5% 0,33W. |
|
R910
P012 |
0790157408 | Carbon 33 KΩ 5% 1/6W. |
| R913 | 0790138804 | Carbon 1 KΩ 5% 1/6W. |
| R914 | 0790151708 | Carbon 12 KΩ 5% 1/6W. |
| R915 | 0790151500 | Carbon 10 KΩ 5% 1/6W. |
| R917 | 0790151500 | Carbon 10 KΩ 5% 1/6W. |
| R910 | 0790125702 | Carbon 75 O 5% 1/6W. |
| R920 | 0790125702 | Carbon 75 Ω 5% 1/4W. |
| R921 | 0790125702 | Carbon 75 Ω 5% 1/4W. |
| R922 | 0790125702 | Carbon 75 Ω 5% 1/4W. |
| R923 | 0790026207 | Carbon 560 Ω 5% 1/4W. |
|
K924
R025 |
0790026207 | Carbon 560 0 5% 1/4W. |
| R926 | 0790137202 | Carbon 680 Ω 5% 1/4W |
| R927 | 0790125702 | Carbon 75 Ω 5% 1/4W. |
| R928 | 0790125702 | Carbon 75 Ω 5% 1/4W. |
| R950 | 0790131908 | Carbon 220 Ω 5% 1/6W. |
| R951 | 0790131908 | Carbon 220 Ω 5% 1/6W. |
| SF200 * | 0090411208 | SAW Filter OFWG 1968 M |
| SW100 | 0130212327 | 4 Key Assy L=3,85 MM |
| sw800 🛆 | 0140203209 | Power Switch |
| S900 | 0330161308 | Scart Connector 21 PIN BLACK |
| S901 | 0330133109 | Video RCA Connector EK105Y |
| 3902 | 0330133208 | AUGIO RUA CONNECTOR EK 105W |
| TUNER | ||
| TU250 * | 0850101502 | UV 915E/IEC Tuner |
| Ref. No. | Part No. | Description | |
|---|---|---|---|
| TRANSFOR | RMERS | ||
| T600 | 0940105307 | Driver Transformer | |
| т650 🛆 | 0940108202 | FBT 21" EC-4A HFT867M | |
| T650A | 0640705117 | Eyelet 2,5-3 | |
| 1650CF | 0330160508 | ||
| 0330100007 | BOWER TROPS EC 44 TYT 0476 04 | ||
| T800A | 0640850210 | Eyelet 1,6-3 | |
| VR200 | 0770511251 | ||
| VR600 | 0770511459 | VR 10 KΩ | |
| VR701 | 0770511350 | VR 2,2 KΩ | |
| VR702 | 0770511053 | VR 100 Ω | |
| VR800 | 0770511350 | VR 2,2 KΩ | |
| X180 | 0090121500 | Quartz Crystai 18.000 MHz | |
| X400 | 0090121104 | Quartz Crystal, 4,4336190 MHz. | |
| ELECTRICA | L ASSY | ||
| AM 1 | 0010203909 | Insulating Ring HV CABLE | |
| BR 1 | 0010203313 | Holder DC GBR-HB7 | |
| BR 2 P | 0010203404 | Wire Band 430/4.8 | |
| BR 2 V | 0010203313 | Holder DC GBR-HBZ | |
| BR 3 V | 0010203503 | Wire Band 98/2.5 | |
| BR10 | 0010202208 | Wire Band 98/2.5 | |
|
BR12
BB12 |
0010202208 | Wire Band 98/2.5 | |
| BR15 | 0010202208 | Wire Band 98/2.5 | |
| BILLIO | 0010202200 | ||
| 0220070004 | |||
| 0330270224 | 2P Connector W/WireS 370+9 mm. | ||
| 0330206208 | 2 WAY Connector Case W/Lead | ||
| CN.FF2 | 0330246802 | 2 WAY Connector Case W/Lead | |
| 0000057400 | Descuration Onth Off | ||
| 0090257106 | Degaussing Coll 21" | ||
| 0090200300 | |||
| SC001 | 0170200406 | Shield Mesh 2 mm. | |
| SC1000 | 0330100009 | Connector | |
| SC1001 | 0010001311 | Spring Ground CRT | |
| SPK 1 | 0030115208 | Speaker 8 Ω 5W. 50X90 | |
| TRC P 🛆 | 1000107605 | A51EAL155X10/X11 21" C.R.T. | |
| TRC V \Lambda | 1000107902 | A51EFS83X191 21" C.R.T. | |
| BAT | 0660100603 | Dry Battery 1,5V. SUM-3 | |
| EM 1 | 0190203604 | Packing Carton 21" E7JPS/EXP | |
| EM 2 | 0190175406 | Upper Cushion Assy E7JS | |
| EM 3 | 0190175505 | Down Cushion Assy E7JS | |
| 0420242208 | Instruc. Book SANYO | ||
| 0000122311 | |||
| Note: P Ex | clusive com | ponent for A51EAL155X10 CRT | |
| V Ex | clusive com | ponent for A51EFS83X191 CRT | |
| A11 · 4 | |||
| All information | tion in this | manual is correct at the start of | |
| production. | Sanyo reser | ves its right to modify components | |
| iures in orde | r to comply with their continuous | ||
| milliovellief | it pulley. | | | | |
Page 15
Page 16
Page 17
Page 18
Page 19
Page 20
NTO DE NORMAS
uente del receptor TV hay is del Manual de Servicio, idicados con ∗ o ⊥ deben iales SANYO.
mentos especialmente (ESD). lación de circuitos debidas precauciones
tán expresados en ohms
- enores de 1 están expresados tán expresados en pF. a es correcta en el inicio de tho de modificarlo para tinua.
- ramas se han efectuado con ajustes normalizados e imagen
COMPLIANCE TO STANDARDS
When any TV receptor component is substituted, it is necessary to check the list of components in the Service Manual and all of those marked with * or _____ must be replaced with original spare SANYO parts
WARNING! This TV set contains components which are MARNING! This IV set contains components which ar particulary sensitive to static electricity (ESD) It is recomended that all due precaution be taken handling integrated circuits and semiconductors.
NOTES:
- -Resistor values are expressed in Ohms
- Resistor values are expressed in Ohms K = 1000, M = 1000000. Capacitor values lower than 1 are expressed in uF and values higher than 1 are expressed in pF. The information in this scheme is correct at the beginning of the series; SANYO reserves the right to modify this in accordance with on-going product improvement policy. The measuraments of voltages and oscillograms were carried out with a TV set tuned to channel-21, normal adjustments and colour bar pattern.
NOTA SUL RISPETTO DELLE NORME
Quando si sosttituisce qaulsiasi componente del recevitore TV deve consultare l'elenco dei componenti nel Manuale per la Manutenzione. Tutti i componenti contrassengati con * o devono essere sostituiti con ricambi originali SANYO.
ATTENZIONE! Questo televisore contiene elementi specialmente sensibili all'elettricità statica (ESD). Consigliamo di realizzare gli interventi sui circuiti integrati e sui semiconduttori con le dovute precauzion
- NOTE: 1.-Tutti i valori delle resistenze sono in OHM, K=1.000, M=1.000.000. 2.-I valori di capacità indicati con un numero minori di 1 son in uF maggiori di 1 sono in pF. 3.-Tutte le informacioni di questo schema sono corrette all'inizio della serie. Seguendo la propria politica di continuo miglioramento dei propri prodotti, la SANYO si riserva il diritto di apportare modifiche senza preavviso.
- Le misure di tensione e gli oscillogrami sono stati effettuati con la TV sintonizzata sul canale 21, regolaz normalizzate e immagine del monoscopio.
Page 21
Page 22
Page 23
MAIN CIRCUIT P.C.B. SOLDER SIDE P.C.B. CIRCUITO GENERAL CARA S P.C.B. PANNELLO PRINCIPALE LAT
Page 24
MAIN CIRCUIT P.C.B. SOLDER SIDE
- P.C.B. CIRCUITO GENERAL CARA SOLDADURAS
- P.C.B. PANNELLO PRINCIPALE LATO SOLDATURE
Page 25
SOCKET CIRCUIT COMPO LOCALIZACION DE COMPO LOCALIZZAZIONE DI COMF
Page 26
MAIN CIRCUIT COMPONENTS LOCATION LOCALIZACION DE COMPONENTES CIRCUITO GENERAL LOCALIZZAZIONE DI COMPONENTI PANNELLO PRINCIPALE
SOCKET CIRCUIT COMPONENTS LOCATION LOCALIZACION DE COMPONENTES CIRCUITO ZOCALO LOCALIZZAZIONE DI COMPONENTI PANNELLO CINESCOPIO
Page 27
SECAM L CIRCUIT P.C.B. COMPONENTS SIDE P.C.B. CIRCUITO SECAM L CARA COMPONENTES P.C.B. PANNELLO SECAM L LATO COMPONENTI
SEC P.C P.C
Page 28
IDE IENTES NENTI
SECAM L CIRCUIT P.C.B. SOLDER SIDE P.C.B. CIRCUITO SECAM L CARA SOLDADURAS P.C.B. PANNELLO SECAM L LATO SOLDATURE
Page 29
SOCKET CIRCUIT COMPONENTS LE LOCALIZACION DE COMPONENTES LOCALIZZAZIONE DI COMPONENTI
E DADURAS .DATURE
Page 30
SOCKET CIRCUIT COMPONENTS LOCATION LOCALIZACION DE COMPONENTES CIRCUITO ZOCALO LOCALIZZAZIONE DI COMPONENTI PANNELLO CINESCOPIO
Page 1
Page 2
Page 3
Page 4
Page 5
Page 6
Page 7
Page 8
Page 9
Page 10
Page 11
Page 12
Page 13
Page 14
Page 15
Page 16
Page 17
Page 18
Page 19
Page 20
Page 21
Page 22
Page 23
Page 24
Page 25
Page 26
Page 27
Page 28
Page 29
Page 30
Loading...