Sanyo PLC-XW15 User Manual

Owner's Manual

PLC-XW15

Multimedia Projector

MODEL

2

Before operating this projector, read this manual thoroughly and operate the projector properly.
This projector provides many convenient features and functions. Operating the projector properly enables you to
manage those features and maintains it in better condition for a considerable time.
Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other
accidents.
If your projector seems to operate improperly, read this manual again, check operations and cable connections and try
the solutions in the “Trouble-shooting” section of the end of this booklet. If the problem still persists, contact the sales
dealer where you purchased the projector or the service center.

TO THE OWNER

SAFETY PRECAUTIONS

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE
OWNER'S MANUAL WITH THIS UNIT.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

● This projector produces intense light from the projection lens. Do not stare directly into the lens as possible.
Eye damage could result. Be especially careful that children do not stare directly into the beam.

● This projector should be set in the way indicated. If not, it may result in a fire hazard.

● Take appropriate space on the top, sides and rear of the projector

cabinet for allowing air circulation and cooling the projector.
Minimum distance should be taken. If the projector is to be built
into a compartment or similarly enclosed, the minimum distances
must be maintained. Do not cover the ventilation slot on the
projector. Heat build-up can reduce the service life of your
projector, and can also be dangerous.

● Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation
holes.

● If the projector is not to be used for an extended time, unplug the projector from the power outlet.

READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.

SIDE and TOP

REAR

20cm

50cm 50cm

50cm

3

SAFETY INSTRUCTIONS

All the safety and operating instructions should be read before
the product is operated.

Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.

Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm,

or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.

Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...

Do not use attachments not recommended by the
manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.

An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.

Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.

The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.

This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.

Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.

This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.

Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.

Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.

Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the

operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.

e. If the projector has been dropped or the cabinet has been

damaged.

f. When the projector exhibits a distinct change in

performance-this indicates a need for service.

When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask
the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.

Voor de klanten in Nederland

Bij dit product zijn batterijen
geleverd.
Wanneer deze leeg zijn,
moet u ze niet weggooien
maar inleveren als KCA.

4

COMPLIANCES

Federal Communication Commission Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.

AC Power Cord for the United Kingdom :

This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin
face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the
same rating, marked thus . If the fuse cover is detachable, never use the plug with the cover omitted. If a
replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug
(i.e. red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions.
If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.
The end of the flexible cord should be suitably prepared and the correct plug fitted. (See Over)

WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET
OUTLET.

The Wires in this mains lead are coloured in accordance with the following code:

Green-and-yellow ············ Earth
Blue ································· Neutral

Brown ······························ Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings
identifying the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked
by the letter E or by the safety earth symbol or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or
coloured red.

WARNING : THIS APPARATUS MUST BE EARTHED.

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada :

AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure
that the plug will fit into the power outlet. Do not try to defeat this safety feature.
Should you be unable to insert the plug into the outlet, contact your electrician.

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

AC POWER CORD REQUIREMENT

GROUND

ASA

5

TABLE OF CONTENTS

FEATURES AND DESIGN 6

BEFORE OPERATION 14

COMPUTER MODE 22

VIDEO MODE 29

SETTING 32

APPENDIX 34

PREPARATION 7

NAME OF EACH PART OF THE PROJECTOR 7
SETTING-UP THE PROJECTOR 8

CONNECTING THE AC POWER CORD 8
POSITIONING THE PROJECTOR 9
ADJUSTABLE FEET 9
MOVING THE PROJECTOR 10

CONNECTING THE PROJECTOR

11

TERMINALS OF THE PROJECTOR 11
CONNECTING TO THE VIDEO EQUIPMENT 12
CONNECTING TO THE COMPUTER 13

OPERATION OF THE REMOTE CONTROL 14

OPERATING RANGE 14
REMOTE CONTROL BATTERIES INSTALLATION 15

TOP CONTROLS AND INDICATORS 16
OPERATING ON-SCREEN MENU 17

HOW TO OPERATE THE ON-SCREEN MENU 17
FLOW OF ON-SCREEN MENU 17
MENU BAR 18

SELECTING COMPUTER MODE 22
SELECTING COMPUTER SYSTEM 22

COMPATIBLE COMPUTER SPECIFICATIONS 23

PC ADJUSTMENT 24
PICTURE IMAGE ADJUSTMENT 26

ADJUST PICTURE IMAGE MANUALLY 26
NORMAL FUNCTION 26
AUTO IMAGE FUNCTION 27

PICTURE POSITION ADJUSTMENT 27
PICTURE SCREEN ADJUSTMENT 28

SELECTING VIDEO MODE 29
SELECTING VIDEO SOURCE 29
SELECTING COLOR SYSTEM 30
PICTURE SCREEN ADJUSTMENT 30
PICTURE IMAGE ADJUSTMENT 31

ADJUSTING THE PICTURE IMAGE MANUALLY 31
NORMAL FUNCTION 31

SETTING MENU 32
SETTING LANGUAGE 33

OPERATING WIRELESS MOUSE 34
MAINTENANCE 35

TEMPERATURE WARNING INDICATOR 35
AIR FILTER CARE AND CLEANING 35
CLEANING THE PROJECTION LENS 35
LAMP REPLACEMENT 36
LAMP REPLACEMENT MONITOR TIMER 36

TROUBLESHOOTING 37
TECHNICAL SPECIFICATIONS 39

BASIC OPERATION 19

TURNING ON / OFF THE PROJECTOR 19
ADJUSTING THE IMAGE 20

ZOOM ADJUSTMENT 20
FOCUS ADJUSTMENT 20
KEY STONE ADJUSTMENT 20
NO SHOW FUNCTION 21
PICTURE FREEZE FUNCTION 21
P-TIMER FUNCTION 21

SOUND ADJUSTMENT 21

SOUND VOLUME ADJUSTMENT 21
SOUND MUTE ADJUSTMENT 21

TRADEMARKS

● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.

● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.

● Windows and PowerPoint are registered trademarks of Microsoft Corporation.

● Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its

respective corporation.

6

FEATURES AND DESIGN

This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of
use. The projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal
display (LCD) technology.

◆ Compatibility

This projector widely accepts various video and
computer input signals including;

● Computers

IBM-compatible and Macintosh computers up
to 1280 x 1024 resolution.

● 6 Color Systems

NTSC, PAL, SECAM, NTSC 4.43, PAL-M or
PAL-N color system can be connected.

● Component Video

Component video signals, such as a DVD
player output high definition TV signals
including 480i, 480p, 575i, 575p, 720p, 1035i
or 1080i, can be connected.

● S-Video

S-Video signals, such as a S-VHS VCR
output signals, can be connected.

◆ High Resolution Image

This projector provides 1024 x 768 dots resolution
for computer input and 550 horizontal TV lines.
The resolution from the computer between XGA
(1024 x 768) and SXGA (1280 x 1024) is
compressed into 1024 x 768 dots. This projector
cannot display image of over 1280 x 1024 dots.
When the resolution of your computer is over than
1280 x 1024, reset the computer output for lower
resolution.

◆ Multi-Scan System

This projector has Multi-Scan System to conform to
almost all computer output signals quickly. There
is no need for troublesome manual adjustment of
frequency and other settings.

◆ Keystone Correction

Positioning height of the projector may result in
distorted images being displayed in a trapezoid
shape. Keystone Correction solves this problem
by digitally altering the projection to produce
undistorted images.

◆ Multilanguage Menu Display

Operation menu is displayed in; English, Deutsch,
Français, Italiano, Español, or Japanese.

◆ One-Touch Auto Imaging

Incoming computer video signals are recognized
and the best setting is automatically selected by
the Auto Image function.
No complicated setup is necessary and projection
is always precise.

◆ Digital Zoom (Computer Mode only)

The Digital Zoom magnifies the image up to 16
times, allowing you to focus on crucial information
at a presentation.

◆ Compact Design

This projector is extremely compact in size and
weight. It is designed to carry and work anywhere
you wish to use.

◆ Power Management

Power Management function is provided to reduce
power consumption while the projector is not in
use.
This Power Management function operates to turn
the Projection Lamp off when the projector detects
signal interruption and any button is not pressed
over 5 minutes. The Projection Lamp is
automatically turned on again when the projector
detects the signal or any operation button is
pressed.
This projector is shipped with this function ON.

◆ Wireless Mouse

The Remote Control Unit supplied with this
projector has Wireless Mouse function for the
connected computer. This function enables you to
operate both projector and computer with this
Remote Control Unit only.

7

PREPARATION

NAME OF EACH PART OF THE PROJECTOR

These Air Intake Vents
should not be blocked.

BOTTOM OF THE CABINET

BACK OF THE CABINET

POWER CORD CONNECTOR

FRONT OF THE CABINET

LAMP COVER

ADJUSTABLE FEET

AND

FEET LOCK LATCHES

PROJECTION LENS

SPEAKER

(Monaural)

INFRARED

REMOTE RECEIVER

LENS COVER

This projector is equipped with cooling
fans for protection from overheating.
Pay attention to the following to ensure
proper ventilation and avoid a possible
risk of fire and malfunction.

● Do not cover the vent slot.

● Keep sides and rear clear of any

obstructions. Obstructions may block
cooling air.

AIR INTAKE VENTS

(Both sides and Rear)

TERMINALS

AND CONNECTORS

AIR INTAKE VENTS

AND AIR FILTERS

ZOOM RING

FOCUS RING

HOT AIR EXHAUSTED !

Air blown from the exhaust vent is hot.
When using or installing the projector, the
following precautions should be taken.

● Do not put a flammable object near this vent.

● Keep the side grills at least 3’ (1m) away

from any object, especially heat-sensitive
object.

● Do not touch this area, especially screws
and metallic parts. This area will become
hot while the projector is used.

This projector detects the internal
temperature and automatically controls the
operating power of the Cooling Fans.

EXHAUST VENT

NOTE ON THE POWER CORD

The AC Power Cord must meet the requirement of the country where you use the projector.
Confirm the AC plug type with the chart below and the proper AC power cord must be used.
If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.

SETTING-UP THE PROJECTOR

8

PREPARATION

To the POWER CORD
CONNECTOR on the
projector.

Projector side AC Outlet side

Ground

To the AC Outlet.

(120 V AC)

For Continental Europe

For the U.S.A. and Canada

This projector uses nominal input voltages of 100-120 V
or 200-240 V AC. The projector automatically selects the
correct input voltage. It is designed to work with single­phase power systems having a grounded neutral
conductor. To reduce the risk of electrical shock, do not
plug into any other type of power system.
Consult your authorized dealer or service station if you
are not sure of the type of power supply being in use.
Connect the projector with the peripheral equipment
before turning the projector on. (Refer to pages 11 ~ 13
for connection.)

CAUTION

For safety, unplug the AC Power Cord when the appli­ance is not used.
When this projector is connected to the outlet with the
AC Power Cord, the appliance is in Stand-by Mode
and consumes a little electric power.

CONNECTING THE AC POWER CORD

Connect the AC Power Cord (supplied)
to the projector.
The AC outlet must be near this
equipment and must be easily
accessible.

For the U.K.

To the AC Outlet.

(200 - 240 V AC)

To the AC Outlet.

(200 - 240 V AC)

9

PREPARATION

POSITIONING THE PROJECTOR

● This projector is designed to project on a flat
projection surface.

● The projector can be focused from 5.2’(1.6m) ~

26.3’(8.0m).

● Refer to the figure below to adjust the screen size.

Screen Size

(W x H) mm

Height (H1)

34”

Height (H2)

690 x 518

18.82”(478mm)

1.57”(40mm)

60”

1219 x 914

33.2”(844mm)

2.8”(70mm)

100”

2032 x 1524

55.4”(1407mm)

4.6”(117mm)

150”

3048 x 2286

83.1”(2110mm)

6.9”(176mm)

200”

4064 x 3048

110.8”(2814mm)

9.2”(234mm)

ADJUSTABLE FEET

Picture tilt and projection angle can be adjusted by
rotating the ADJUSTABLE FEET. Projection angle can
be adjusted to 7.6 degrees.

Lift the front of the projector and pull the FEET LOCK
LATCHES on both sides of the projector.

1

ADJUSTABLE FEET

FEET LOCK
LATCHES

H1

H2

200”

167”

150”

125”

100”

83”

60”
50”

41”

26.3’ (8.0m)

19.7’ (6.0m)

13.1’ (4.0m)

7.8’ (2.4m)

5.2’ (1.6m)

34”

Release the FEET LOCK LATCHES to lock the
ADJUSTABLE FEET and rotate the ADJUSTABLE FEET
to fine tune the position and the tilt.

2

To shorten the ADJUSTABLE FEET, lift the front of the
projector and pull and undo the FEET LOCK LATCHES.

The position and the keystone distortion of the image can
be adjusted using the Menu Operation. (Refer to P 20,
28 and 30.)

3

ROOM LIGHT

The brightness in the room has a great
influence on the picture quality. It is
recommended to limit ambient lighting in
order to provide the best image.

Max. Zoom

Min. Zoom

10

PREPARATION

When moving the projector, replace the lens cover and retract the feet to prevent damage to the lens and
cabinet.
When this projector is not in use for an extended period, put it into the case (carrying bag) supplied with this
projector.

CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR

● Do not drop or bump the projector, otherwise damages or malfunctions may result.

● When carrying the projector, use a suitable carrying case.

● Do not transport the projector by using a courier or transport service in an unsuitable transport case. This

may cause damage to the projector. To transport the projector through a courier or transport service,
consult your dealer for best way.

MOVING THE PROJECTOR

CAUTION

The Carrying Bag (supplied) is intended for protection from dust and scratches on the surface of the cabinet, and
it is not designed to protect the LCD projector from external forces. Do not transport the projector through a
courier or transport services with this bag. The projector can be damaged. When handling the projector, do not
drop or bump the projector, subject it to strong forces or put other things on the cabinet.

11

CONNECTING THE PROJECTOR

TERMINALS OF THE PROJECTOR

COMPUTER INPUT TERMINAL

Terminal : HDB15-PIN

Connect the display output terminal of the computer to
COMPUTER INPUT terminal of this projector with the
VGA Cable (supplied). When connecting the
Macintosh computer, the MAC Adapter (not supplied)
is required.

Red Input

Ground (Horiz.sync.)

Green Input

Sense 2

Blue Input

Ground (Red)

Ground (Green)

Ground (Blue)

1

5

2

4

3

6
7
8

No Connect

Horiz. sync.

Ground (Vert.sync.)

Sense 1

Sense 0

Vert. sync.

Reserved

9

13

10

12

11

14
15

Pin Configuration

Terminal : DIN 8-PIN

Connect control port (PS/2, Serial or ADB port) on your
computer to this terminal with the Control Cable (the Control
Cable for PS/2 port is supplied).

Pin Configuration

CONTROL PORT CONNECTOR

-----

CLK

DATA

GND

-----

-----

GND

-----

R X D

-----

-----

GND

RTS

T X D

GND
GND

-----

ADB

-----

GND

-----

-----

-----

GND

PS/2 Serial ADB
1
2
3
4
5
6
7
8

Connect the computer output to
this terminal.
(Refer to P13.)

When controlling the computer with
the Remote Control of this projector,
connect the mouse port of your
personal computer to this terminal.
(Refer to P13.)

Connect an external audio
amplifier to this terminal.
(Refer to P12, 13.)

Connect the S-VIDEO output
from the video equipment to this
terminal. (Refer to P12.)

Connect the audio output from
the computer to this terminal.
(Refer to P13.)

Connect the audio output from
the video equipment to this
terminal. (Refer to P12.)

COMPUTER INPUT TERMINAL

CONTROL PORT CONNECTOR

COMPUTER AUDIO INPUT JACK

AUDIO INPUT JACK

VIDEO INPUT JACKS

(VIDEO/Y, Pb/Cb, Pr/Cr)

S-VIDEO INPUT JACK

AUDIO OUTPUT JACK (STEREO)

Connect the composite video
output from the video equipment
to the VIDEO/Y jack or connect
the component video outputs to
the Y/VIDEO, Pb/Cb and Pr/Cr
jacks. (Refer to P12.)

This projector uses a micro
processor to control the unit.
Occasionally, the micro
processor may malfunction and
need to be reset. This can be
done by pressing the RESET
button with a pen, which will
shut down and restart the unit.
Do not use the RESET function
excessively.

RESET BUTTON

VIDEO

Y – Pb/Cb – Pr/Cr

RESET

AUDIO OUT

AV

AUDIO

IN

COMPUTER IN

S – VIDEO

COMPUTER

CONTROL PORT

2

34

9 678

13

1

12

11

5

15

10

14

8 7 6

3

5

4

1

2

12

CONNECTING THE PROJECTOR

CONNECTING TO THE VIDEO EQUIPMENT

Video Source (example)

Video Cassette Recorder Video Disc Player

Video Cables ✽

S-VIDEO

Cable ✽

Audio Amplifier

Audio Speaker (stereo)

Audio Cable

(Stereo)

✽

Terminals

of the Projector

Use any of VIDEO jack Y-Pb/Cb-Pr/Cr
jacks or S-VIDEO jack.

• When both VIDEO jack and S­VIDEO jack are connected, the S­VIDEO jack has priority over the
VIDEO jack.

• When both Y-Pb/Cb-Pr/Cr jacks and
S-VIDEO jack are connected, the Y­Pb/Cb-Pr/Cr jacks has priority over
the S-VIDEO jack.

S-VIDEO Output

Audio Input

Cables used for connection (✽ = Cables are not supplied with this projector.)

• Video Cable (RCA x 1 or RCA x 3)

✽

• S-VIDEO Cable ✽

• Audio Cable (RCA x 2- Mini Plug x 1 (stereo) or Mini Plug (stereo)) ✽

NOTE :
When connecting the cable, the power cords of
both the projector and the external equipment
should be disconnected from AC outlet. Turn the
projector and peripheral equipment on before the
computer is switched on.

Audio Output

Audio

Cable ✽

Y Pb/Cb Pr/Cr R L

(stereo)

External Audio Equipment

AV AUDIO IN

S-VIDEO

Y-Pb/Cb-Pr/Cr

VIDEO

AUDIO OUT

Component video output equipment.

(such as DVD player or

high-definition TV source.)

Composite

Video Output

Component

Video Output

VIDEO

Y – Pb/Cb – Pr/Cr

S – VIDEO

RESET

COMPUTER IN

AUDIO OUT

AV

COMPUTER

AUDIO

IN

CONTROL PORT