Sanyo PLC-XU22N User Manual

Multimedia Projector

MODEL PLC-XU22N

Owner's Manual

INFORMATION TO THE USER

NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

TO THE OWNER

As the owner of a new Multimedia Projector, you are probably eager to try out your new projector. Before you do, we suggest that your spend a little time reading this manual to familiarize yourself with the operating procedures, so that you will receive maximum satisfaction from the many features included in your new projector.

This owner's manual will acquaint you with your projector's features. Reading it will help us too. Through the years, we have found that many service requests were not caused by problems with our projectors. They were caused by problems that could have been prevented, if the owner had followed the instructions in the manual.

You can often correct operating problems yourself. If your projector fails to work properly, see "TROUBLESHOOTING" section on pages 44 ~ 45 and try the solution marked for each problem.

SAFETY PRECAUTIONS

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This Projector has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature.

This projector produces intense light from the projection lens. Do not stare directly into the lens as possible eye damage could result. Be especially careful that children do not stare directly into the beam. The Remote Control Unit, supplied to this projector, emits the laser beam as the Laser Pointer function from the Laser Light Window while pressing the LASER button (for 1 minute). Do not look into the Laser Light Window or shine the laser beam on yourself or other people. Eye damage may result.

This projector should be set in the way indicated. If not, It may result in fire hazard.

If the projector will not be used for an extended time, unplug the projector from the power outlet.

READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE OWNER'S MANUAL WITH THIS UNIT.

2

IMPORTANT SAFETY INSTRUCTIONS

All the safety and operating instructions should be read before the product is operated.

Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

Do not use attachments not recommended by the manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall of shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers.

Do not expose this unit to rain or use near water... for

example, in a wet basement, near a swimming pool, etc...

Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.

The openings should never be covered with cloth of other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.

This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided.

This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.

Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by persons walking on it.

d.If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.

e.If the projector has been dropped or the cabinet has been damaged.

f.When the projector exhibits a distinct change in performance-this indicates a need for service.

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.

		This projector is equipped with a
		grounding type AC line plug.
		Should you be unable to insert the
		plug into the outlet, contact your
		electrician. Do not defeat the
	GROUND	safety purpose of this grounding
		type plug.

Follow all warnings and instructions marked on the projectors.

For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges.

An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector.

Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power cord or plug is damaged or frayed.

b.If liquid has been spilled into the projector.

c.If the projector has been exposed to rain or water.

If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained.

Do not cover the ventilation slot on the projector.

Heat build-up can reduce the service life of your projector, and can also be dangerous.

20cm

WALL

	PROJECTOR	PROJECTOR
	(FRONT)	(SIDE)
50cm	50cm	50cm

3

17

TABLE OF CONTENTS

FEATURES AND DESIGN

5 COMPUTER MODE

23

PREPARATION

NAME OF EACH PART OF THE PROJECTOR SETTING-UP THE PROJECTOR

POSITIONING THE PROJECTOR ADJUSTABLE FEET

CONNECTING THE AC POWER CORD VENTILATION

MOVING THE PROJECTOR

CONNECTING THE PROJECTOR

TERMINALS OF THE PROJECTOR CONNECTING TO THE VIDEO EQUIPMENT CONNECTING TO THE COMPUTER

BEFORE OPERATION

OPERATION OF THE REMOTE CONTROL

LASER POINTER FUNCTION

REMOTE CONTROL BATTERIES INSTALLATION

TOP CONTROLS AND INDICATORS OPERATING ON-SCREEN MENU

HOW TO OPERATE THE ON-SCREEN MENU FLOW OF ON-SCREEN MENU

		SELECTING COMPUTER MODE	23
	6	SELECTING COMPUTER SYSTEM	23
		PC ADJUSTMENT	24
	6	COMPATIBLE COMPUTER SPECIFICATION	26
		PICTURE IMAGE ADJUSTMENT	27
	7	PICTURE POSITION ADJUSTMENT	28
	7	PICTURE SCREEN ADJUSTMENT	29
	7
	8
	8	VIDEO MODE	30
	9
		SELECTING VIDEO MODE	30
	10	SELECTING COLOR SYSTEM	30
		PICTURE SCREEN ADJUSTMENT	30
	10	PICTURE IMAGE ADJUSTMENT	31
	11
	12	MCI MODE	32
	14	OPERATING THE PC CARD SLOT	32
		SELECTING MCI MODE	33
	14	SHOW THE DATA IN THE MEMORY CARD	34
		WRITE DATA INTO THE MEMORY CARD	35
	14	PICTURE IMAGE ADJUSTMENT	36
	15	PICTURE POSITION ADJUSTMENT	36
	16
		PICTURE SCREEN ADJUSTMENT	37
	17
		SMART MEDIA AND PC CARD ADAPTER	38
	17

BASIC OPERATION

TURNING ON / OFF THE PROJECTOR ADJUSTING THE IMAGE

ZOOM ADJUSTMENT

FOCUS ADJUSTMENT KEYSTONE ADJUSTMENT NO SHOW FUNCTION PICTURE FREEZE FUNCTION

SOUND ADJUSTMENT

SOUND VOLUME ADJUSTMENT SOUND MUTE ADJUSTMENT

		SETTING	40
	20	SETTING MENU	40
		SETTING LANGUAGE	40

		APPENDIX	41
	21	OPERATING WIRELESS MOUSE	41
	22	MAINTENANCE	42
	22	TEMPERATURE WARNING INDICATOR	42
	22
		AIR FILTER CARE AND CLEANING	42
	22	CLEANING THE PROJECTION LENS	42
	22	LAMP REPLACEMENT	43
		LAMP REPLACEMENT MONITOR TIMER	43

TROUBLESHOOTING	44
TECHNICAL SPECIFICATIONS	46

TRADEMARKS

●Apple, Macintosh, and PowerBook are trademarks or

●IBM and PS/2 are trademarks or registered

●Windows and PowerPoint are registered trademarks of

●Each name of corporations or products in the respective corporation.

4

FEATURES AND DESIGN

This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. The projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology.

Compatibility

This projector is compatible with many different types of personal computers and video devices, including;

●IBM-compatible computers, including laptops, up to 1280 x 1024 resolution.

●Apple Macintosh and PowerBook computers up to 1280 x 1024 resolution.

●Various video equipment using any of the world wide video standards, including NTSC, NTSC4.43, SECAM, PAL, PAL-M and PAL-N.

Image Resolution

Picture Image of the computer is projected in the resolution of 1024 x 768 and it is provided just as appearing on your computer's monitor. Screen resolutions between 1024 x 768 and 1280 x 1024 are compressed to 1024 x 768, and this projector cannot display screen resolutions above 1280 x 1024. If your computer's screen resolution is higher than 1280 x 1024, reset it to a lower resolution before you connect the projector.

PC CARD SLOT

This projector has the PC CARD SLOT for easier presentation. Pictures can be projected just by inserting a memory card including image data and the presentation data can be edited by the software "Media Card Imager" (supplied) easily. Refer to the pages 32 ~ 39 and the Owner's Manual for Media Card imager for operations.

Laser Pointer Function

The Remote Control Unit of this projector has the Laser Pointer function providing convenience and smartness for your presentations.

Other Features

This projector has Motor Zoom/Focus, No Show, Picture Freeze, Keystone and Mute functions. And the Air Pad Remote Control is equipped.

Portability

This projector is quite compact in size and weight. Having a sophisticated shape like an attaché case with a retractable carrying handle, the projector will help you make powerful presentation wherever you go.

Automatic Multiscanning System

This projector automatically tune to the most personal computers currently distributed by simply connecting. It is free from complicated adjustments to project picture images from PC.

Accessories

This projector comes with the parts listed below. Check to make sure all are included. If any parts are missing, contact to a sales dealer.

●Owner's Manual.

●AC Power Cord.

●Wireless Remote Control Unit.

●Batteries for Remote Control Unit.

●VGA Cable.

●Control Cable for PS/2 Port.

●Media Card Imager for Windows 95 (CD-ROM) and Owner’s Manual for this software.

●SmartMedia and PC Card Adapter.

●Lens Cover.

●Dust Cover.

Multilanguage Menu Display

Operation menu is displayed in; English, Deutsch, Français, Italiano, Español, or Japanese

5

PREPARATION

NAME OF EACH PART OF THE PROJECTOR

FRONT OF THE CABINET

PROJECTION LENS

PC CARD SLOT

LENS COVER

INFRARED REMOTE RECEIVER

BACK OF THE CABINET

EXHAUST VENT

HOT AIR EXHAUSTED !

Air blown from the exhaust vent is hot. When using or installing the projector, following attention should be taken.

● Do not put a flammable object near this part.

Keep heat-sensitive objects away from the exhaust vent.

●Do not touch this part especially screws and metallic parts. This part will become hot while the projector is used.

POWER CORD CONNECTOR

BOTTOM OF THE CABINET

AIR INTAKE VENTS

These Air Intake Vents should not be blocked.

CARRY HANDLE

SPEAKER (Monaural)

INFRARED

REMOTE RECEIVER

ADJUSTABLE FEET

AND

FEET LOCK LATCHES

LAMP COVER

6

PREPARATION

SETTING-UP THE PROJECTOR

POSITIONING THE PROJECTOR

●This projector is basically designed to project on a flat projection surface.

●The projector can be focused from 4.6’(1.4m) ~ 35.4’(10.8m).

●Refer to the figure below to adjust the screen size.

35.4’ (10.8m)

24.0’ (7.3m)

300”

18.0’ (5.5m)

11.8’ (3.6m)

200”

150”

231”

H1

4.6’ (1.4m)

100”

154”

40”

77”

115”

H2

30”

Screen Size

30”

60”

100”

150”

200”

300”

(W x H) mm

610 x 457

1219 x 914

2032 x 1524

3048 x 2286

4064 x 3048

6096 x 4572

Height (H1)

17.1”(435mm)

34.3”(870mm)

57.1”(1451mm)

85.7”(2177mm)

114.3”(2903mm)

171.4”(4354mm)

Height (H2)

0.9”(22mm)

1.7”(44mm)

2.9”(73mm)

4.3”(109mm)

5.7”(145mm)

8.6”(218mm)

ROOM LIGHT

The brightness in the room has a great influence on the picture quality. It is recommended to limit ambient lighting in order to provide the best image.

ADJUSTABLE FEET

Picture tilt and projection angle can be adjusted by rotating the ADJUSTABLE FEET. Projection angle can be adjusted to 10 degrees.

1	Lift the front of the projector and pull the FEET LOCK
	LATCHES on both sides of the projector.
2	Release the FEET LOCK LATCHES to lock the
	ADJUSTABLE FEET and rotate the ADJUSTABLE
	FEET for fine tune of the position and the tilt.
3	To shorten the ADJUSTABLE FEET, lift the front of the
	projector and pull and undo the FEET LOCK LATCHES.

The position and the keystone distortion of the image can be also adjusted with the Menu Operation. (Refer to P 21, 29, 30 and 37.)

ADJUSTABLE FEET

FEET LOCK LATCHES

7

PREPARATION

CONNECTING THE AC POWER CORD

This projector uses nominal input voltages of 100-120 V AC. The projector automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system.

Consult your authorized dealer or service station if your are not sure of the type of power supply being in use. Connect the projector with the peripheral equipment before turning the projector on. (Refer to pages 10 ~ 13 for connection.)

CAUTION

For the safety, unplug the AC Power Cord when the appliance is not used.

When this projector is connected to the outlet with the AC Power Cord, the appliance is in Stand-by Mode and consumes a little electric power.

Connect the AC power supply cord (provided) to the projector.

The socket-outlet must be near this equipment and must be easily accessible.

Projector side (Female)		AC outlet side (Male)

VENTILATION

This projector is equipped cooling fans for protection from overheating. ensure the ventilation and avoid a possible risk of fire and malfunction.

●Do not cover the vent slot.

●Keep the rear grill at least one meter away from any object.

●Make sure that there is no object on both sides of the projector. Those obstacles may prevent the projector from taking the cooling air through the side Air Intake Vent Slots.

Pay attention to the following to

EXHAUST VENT

(REAR SIDE)

AIR INTAKE VENTS (BOTH SIDES)

8

PREPARATION

MOVING THE PROJECTOR

Use the Carry Handle when moving the Projector.

When moving the projector, replace the lens cover and rotate the feet fully clockwise (to shorten the feet) to prevent from damage to the lens and the cabinet.

When this projector is not used for the extended period, replace the lens cover, tuck the Adjustable Feet and apply the dust cover supplied to this projector.

CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR

●Do not drop or give a shock to the projector, otherwise damages or malfunctions may result.

●When carrying the projector, use a carrying case recommended by Sanyo.

●Do not transport the projector by using a courier or transport service in an unsuitable transport case. This may cause damage to the projector. To transport the projector through a courier or transport service, use a case recommended by Sanyo.

●For carrying or transportation cases, contact a Sanyo authorized dealer.

9

CONNECTING THE PROJECTOR

TERMINALS OF THE PROJECTOR

S-VIDEO INPUT JACK

Connect the S-VIDEO output from the video equipment to this terminal.

(Refer to P11.)

AUDIO INPUT JACKS

Connect the audio outputs from the video equipment to these terminals.

(Refer to P11.)

● When the audio output is monaural, connect it to the Left jack.

COMPUTER INPUT TERMINAL

Connect the computer output to this terminal.

(Refer to P12, 13.)

MONITOR OUTPUT TERMINAL

This terminal outputs the signal from the COMPUTER IN terminal. Connect to the monitor to this terminal.

(Refer to P12, 13.)

VIDEO INPUT JACK

	S-VIDEO
	R-AUDIO-L(MONO)	VIDEO	AUDIO
			IN
			OUT

Connect the video output from the video equipment to this terminal.

(Refer to P11.)

COMPUTER AUDIO INPUT JACK

Connect the audio output from the computer to this terminal. (Refer to P12, 13.)

COMPUTER IN

AUDIO OUTPUT JACK (STEREO)

MONITOR OUT	Connect the audio amplifier to
	this terminal.
CONTROL PORT	(Refer to P12, 13.)

CONTROL PORT CONNECTOR

When controlling the computer with the Remote Control of this projector, connect the mouse port of your personal computer to this terminal. It is also used for write on or read from the data of the PC CARD SLOT in MCI mode.

(Refer to P12, 13, 35.)

COMPUTER INPUT / MONITOR OUTPUT TERMINAL

Terminal : HDB15-PIN

Connect the display output terminal of the computer to COMPUTER INPUT with the VGA Cable (supplied). And connect the monitor to MONITOR OUTPUT with the monitor cable (not supplied). When connecting the Macintosh computer, the MAC/VGA Adapter (not supplied) is required.

Pin Configuration					1	Red Input	9	Non Connect
					2	Green Input	10	Ground (Vert.sync.)
					3	Blue Input	11	Sense 0
5	4	3	2	1	4	Sense 2	12	Sense 1
10	9		8	7 6	5	Ground (Horiz.sync.)	13	Horiz. sync.
15	14	13	12	11	6	Ground (Red)	14	Vert. sync.
					7	Ground (Green)	15	Reserved
					8	Ground (Blue)

CONTROL PORT CONNECTOR

Terminal : DIN 8-PIN

Connect control port (PS/2, Serial or ADB port) on your computer to this terminal with the Control Cable (the Control Cable for PS/2 port is supplied).

Pin Configuration					PS/2	Serial	ADB
				1	-----	R X D	-----
				2	CLK	-----	ADB
8	7	6		3	DATA	-----	-----
				4	GND	GND	GND
5	4	3
2	1			5	-----	RTS	-----
				6	-----	T X D	-----
				7	GND	GND	-----
				8	-----	GND	GND

10

CONNECTING THE PROJECTOR

CONNECTING TO THE VIDEO EQUIPMENT

Video Source (example)
Video Cassette Recorder	Video Disc Player

Used cables for connection

•VIDEO CABLE

•S-VIDEO CABLE

•AUDIO CABLE (stereo)

These cables are not supplied with this projector.

Video / Audio Output	S-VIDEO Output

Video Audio Cable

S-VIDEO Cable

	S-VIDEO
	R-AUDIO-L(MONO)	VIDEO	AUDIO
			IN

OUT

COMPUTER IN

MONITOR OUT

Use the either of VIDEO jack or S-VIDEO jack. When the both jacks are connected, the S-VIDEO jack has priority over the VIDEO jack.

Terminals

of the Projector

CONTROL PORT

NOTE :

When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

Audio Cable (Stereo)

External Audio Equipment					Audio Input
	Audio Speaker
	(stereo)				Audio Amplifier

11

CONNECTING THE PROJECTOR

CONNECTING TO THE COMPUTER

To connect with the computer, refer to the figure below.

Used cables for connection

•VGA CABLE

•CONTROL CABLE FOR PS/2 PORT

•CONTROL CABLE FOR SERIAL PORT,or ADB PORT

•MAC ADAPTER

•MONITOR CABLE

•PC AUDIO CABLE (stereo)

These cables are not supplied with this projector.

IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA / SXGA)

Desktop type

Laptop type

Monitor

Audio Speaker

(stereo)

Audio Amplifier

To each terminal of your computer

To the Monitor

Monitor Output

Serial port PS/2 port

MAC Adapter

Set the slide

ON	DIP	switches following
1 2	3 4 5 6	the chart on the

next page.

Terminal

Terminal

ADB port Audio Output				Audio Input

Terminal

Audio Cable (stereo)

Control Cable for ADB Port

Control Cable for PS/2 Port

Control Cable for Serial Port

VGA Cable

Monitor Cable

NOTE :

When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

12

CONNECTING THE PROJECTOR

	S-VIDEO
	R-AUDIO-L(MONO)	VIDEO	AUDIO
			IN

OUT

COMPUTER IN

MONITOR OUT

CONTROL PORT

COMPUTER

MONITOR

CONTROL

AUDIO

AUDIO

IN

OUT

PORT

IN

OUT

Use one of these Control Cables corresponding with the terminal of your computer.

MAC ADAPTER (Not supplied)

Set the switches as shown
in the table below depend-		ON
ing on the RESOLUTION				ON				DIP
MODE that you want to				1	2	3	4	5	6
use before your turn on the		OFF
projector and computer.
	1	2	3	4					5	6
13" MODE (640 x 480)	ON	ON	OFF	OFF				OFF		OFF
16" MODE (832 x 624)	OFF	ON	OFF	ON				OFF		OFF
19" MODE (1024 x 768)	OFF	ON	ON	OFF				OFF		OFF
21" MODE (1152 x 870)	ON	ON	ON	ON				OFF		OFF

13

BEFORE OPERATION

OPERATION OF THE REMOTE CONTROL

Left Side

ON

ALL

OFF

ALL-OFF SWITCH

When using the Remote Control Unit, turn this switch to “ON” and turn it “ALL OFF” when it is not used.

VIDEO BUTTON

Used to select VIDEO source. (P30)

COMPUTER/MCI BUTTON

Used to select source either COMPUTER or MCI mode. (P23, 33)

MENU BUTTON

Used to call MENU operation. (P17-19)

SELECT BUTTON

Used to execute the item selected or to expand the image in DIGITAL ZOOM mode. (P29, 37)

It is also used as a PC mouse in Wireless Mouse Operation. (P41)

LASER BUTTON

Used to operate laser pointer function. The laser beam is emitted while pressing this button within 1 minute. When using the laser pointer for more than 1 minute, release the button and press it again.

COMPUTER/ MCI VIDEO ON-OFF

ZOOM FOCUS VOLUME

MUTE D.ZOOM PAGE

MENU

LASER

KEYSTONE

NO SHOW	FREEZE
AUTO IMAGE	NORMAL

POWER ON-OFF BUTTON

Used to turn the projector on or off. (P20)

POINT BUTTON

Used to move the pointer on the MENU, to adjust the item, or to pan the image in DIGITAL ZOOM mode. (P29, 37)

It is also used as a PC mouse in Wireless Mouse Operation. (P41)

When pressing the center of this button, it works as the SELECT button.

RIGHT CLICK BUTTON

Used to compress the image in DIGITAL ZOOM mode. (P29, 30, 37)

It is also used as a PC mouse in Wireless Mouse Operation. (P41)

LASER POINTER FUNCTION

This remote control emits a laser beam as the Laser Pointer from the Laser Light Window. When the LASER button is pressed, the laser light goes on. And when the button is pressed more than 1 minute or the button is released, light goes off. Laser light is emitted with the RED light which tells the laser beam being emitted.

The laser emitted is a class II laser; therefore, do not look into the Laser Light Window or shine the laser beam on yourself or other people. The three marks bellow are the caution labels for the laser beam.

CAUTION : Use of controls or adjustments or performance of procedures other than those specified herein may result hazardous radiation exposure.

These caution labels are put on the remote control.

Laser Light Window

14

BEFORE OPERATION

	COMPUTER/
	MCI	VIDEO ON-OFF
ZOOM BUTTON
Used to adjust zoom.	ZOOM	FOCUS VOLUME
(P21)
FOCUS BUTTON	MUTE	D.ZOOM	PAGE
Used to adjust focus.
(P21)
	MENU

MUTE BUTTON

Used to mute sound.(P22)

LASER

NO SHOW BUTTON

Used to turn the picture into black image. (P22)

AUTO IMAGE BUTTON

Use to operate AUTO IMAGE function. (P28)

KEYSTONE
NO SHOW	FREEZE
AUTO IMAGE	NORMAL

VOLUME

Used to (P22)

D.ZOOM

Used to turn into DIGITAL mode. (P29,

PAGE BUTTONS

Used to move to next / previous page of the data in memory card. This buttons are activated in MCI mode only. (P34)

FREEZE

Used to stop (P22)

NORMAL

Used to reset picture

by the factory (P27, 31, 36)

KEY STONE

Used to stone distortion (P22, 29, 30,

Operating Range

Point the remote control toward the projector (Receiver Window) whenever pressing the buttons. Maximum operating range for the remote control is about 16.4’ (5m) and 60° front and rear of the projector

60°

16.4’ (5 m)

16.4’ (5 m)

60°

REMOTE CONTROL BATTERIES INSTALLATION

1	2	3	the compartment
	Press the lid down-	Two AA size batteries
	ward and slide it.	For correct polarity (+
		and –), be sure the
		battery terminals are in
		contact with the pins in
		the compartment.

To insure safe operation, please observe the following precautions :

●Use (2) AA type alkaline batteries.

●Replace two batteries at the same time.

● Do not use a new battery with a used battery.

●Avoid contact with water or liquid.

●Do not expose the Remote Control Units to moisture, or heat.

●Do not drop the remote control unit.

●If batteries have leaked on the remote control, carefully wipe the case clean and load new batteries.

15