Multimedia Projector
MODEL PLC-XU20E
Owner's Manual
TO THE OWNER
As the owner of a new Multimedia Projector, you are probably eager to try out your new projector. Before you do, we suggest that your spend a little time reading this manual to familiarize yourself with the operating procedures so that you will receive maximum satisfaction from the many features included in your new projector.
This owner's manual will acquaint you with your projector's features. Reading it will help us too. Through the years, we have found that many service requests were not caused by problems with our projectors. They were caused by problems that could have been prevented, if the owner had followed the instructions in the manual.
You can often correct operating problems yourself. If your projector fails to work properly, see "TROUBLESHOOTING" section on pages 35 ~ 36 and try the solution marked for each problem.
SAFETY PRECAUTIONS
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
This projector produces intense light from the projection lens. Do not stare directly into the lens as possible eye damage could result. Be especially careful that children do not stare directly into the beam. The Remote Control Unit, supplied to this projector, emits the laser beam as the Laser Pointer function from the Laser Light Window while pressing the LASER button (for 1 minute). Do not look into the Laser Light Window or shine the laser beam on yourself or other people. Eye damage may result.
This projector should be set in the way indicated. If not, It may result in fire hazard.
If the projector will not be used for an extended time, unplug the projector from the power outlet.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.
IMPORTANT :
For your protection in the event of theft or loss of this LCD projector, please record the Model Number and Serial Number located on the rear of unit and retain this information. Refer to these numbers whenever you call upon your authorized dealer regarding this product.
Do not discard shipping carton and packing materials. These items may be needed for storage or future servicing.
Model No :
Serial No :
2
IMPORTANT SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before the product is operated.
Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
Do not use attachments not recommended by the manufacturer as they may cause hazards.
Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturer.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.
The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.
This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided.
This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.
Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by persons walking on it.
Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector.
Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions:
a.When the power cord or plug is damaged or frayed.
b.If liquid has been spilled into the projector.
c.If the projector has been exposed to rain or water.
d.If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.
e.If the projector has been dropped or the cabinet has been damaged.
f.When the projector exhibits a distinct change in performance-this indicates a need for service.
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.
Follow all warnings and instructions marked on the projectors.
For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges.
An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained.
Do not cover the ventilation slot on the projector.
Heat build-up can reduce the service life of your projector, and can also be dangerous.
20cm
WALL
|
PROJECTOR |
PROJECTOR |
|
(FRONT) |
(SIDE) |
50cm |
50cm |
50cm |
3
TABLE OF CONTENTS
FEATURES AND DESIGN |
5 |
COMPUTER MODE |
22 |
|
|
SELECTING COMPUTER MODE |
22 |
PREPARATION |
6 |
SELECTING COMPUTER SYSTEM |
22 |
AUTOMATIC MULTISCANNING SYSTEM |
22 |
||
|
|
COMPATIBLE COMPUTER SPECIFICATIONS |
23 |
NAME OF EACH PART OF THE PROJECTOR |
6 |
PC ADJUSTMENT |
24 |
SETTING-UP THE PROJECTOR |
7 |
PICTURE IMAGE ADJUSTMENT |
26 |
POSITIONING THE PROJECTOR |
7 |
ADJUST PICTURE IMAGE MANUALLY |
26 |
ADJUSTABLE FEET |
7 |
NORMAL FUNCTION |
26 |
CONNECTING THE AC POWER CORD |
8 |
AUTO IMAGE FUNCTION |
27 |
VENTILATION |
8 |
PICTURE POSITION ADJUSTMENT |
27 |
MOVING THE PROJECTOR |
9 |
PICTURE SCREEN ADJUSTMENT |
28 |
CONNECTING THE PROJECTOR |
10 |
VIDEO MODE |
29 |
TERMINALS OF THE PROJECTOR CONNECTING TO THE VIDEO EQUIPMENT CONNECTING TO THE COMPUTER
BEFORE OPERATION
OPERATION OF THE REMOTE CONTROL
LASER POINTER FUNCTION
REMOTE CONTROL BATTERIES INSTALLATION
10 |
SELECTING VIDEO MODE |
29 |
|
11 |
SELECTING COLOUR SYSTEM |
29 |
|
12 |
PICTURE SCREEN ADJUSTMENT |
29 |
|
|
PICTURE IMAGE ADJUSTMENT |
30 |
|
14 |
ADJUSTING THE PICTURE IMAGE MANUALLY |
30 |
|
NORMAL FUNCTION |
30 |
||
|
|||
14 |
SETTING |
31 |
|
14 |
|||
15 |
|
|
TOP CONTROLS AND INDICATORS |
16 |
SETTING MENU |
31 |
OPERATING ON-SCREEN MENU |
17 |
SETTING LANGUAGE |
31 |
HOW TO OPERATE THE ON-SCREEN MENU |
17 |
|
|
FLOW OF ON-SCREEN MENU |
17 |
|
|
MENU BAR |
18 |
APPENDIX |
32 |
|
|
||
BASIC OPERATION |
19 |
|
|
TURNING ON / OFF THE PROJECTOR ADJUSTING THE IMAGE
ZOOM ADJUSTMENT
FOCUS ADJUSTMENT KEY STONE ADJUSTMENT NO SHOW FUNCTION
PICTURE FREEZE FUNCTION
SOUND ADJUSTMENT
SOUND VOLUME ADJUSTMENT SOUND MUTE ADJUSTMENT
19 |
TEMPERATURE WARNING INDICATOR |
33 |
|
20 |
AIR FILTER CARE AND CLEANING |
33 |
|
CLEANING THE PROJECTION LENS |
33 |
||
20 |
|||
LAMP REPLACEMENT |
34 |
||
20 |
|||
LAMP REPLACEMENT MONITOR TIMER |
34 |
||
20 |
|||
TROUBLESHOOTING |
35 |
||
21 |
|||
TECHNICAL SPECIFICATIONS |
37 |
||
21 |
|||
21 |
|
|
|
21 |
|
|
|
21 |
|
|
TRADEMARKS
●Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
●IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
●Windows and PowerPoint are registered trademarks of Microsoft Corporation.
●Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its respective corporation.
4
FEATURES AND DESIGN
This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. The projector utilizes built-in multimedia features, a palette of 16.77 million colours, and matrix liquid crystal display (LCD) technology.
Compatibility
This projector is compatible with many different types of personal computers and video devices, including;
●IBM-compatible computers, including laptops, up to 1280 x 1024 resolution.
●Apple Macintosh and PowerBook computers up to 1280 x 1024 resolution.
●Various video equipment using any of the world wide video standards, including NTSC, NTSC4.43, SECAM, PAL, PAL-M and PAL-N.
Automatic Multiscanning System
This projector automatically tunes to most personal computers currently distributed by simply connecting. It is free from complicated adjustments to project picture images from most Personal Computers.
Multilanguage Menu Display
Operation menu is displayed in; English, Deutsch, Français, Italiano, Español, or Japanese.
Image Resolution
Picture Image of the computer is projected in the resolution of 1024 x 768 and it is provided just as appearing on your computer's monitor. Screen resolutions between 1024 x 768 and 1280 x 1024 are compressed to 1024 x 768, and this projector cannot display screen resolutions above 1280 x 1024. If your computer's screen resolution is higher than 1280 x 1024, reset it to a lower resolution before you connect the projector.
Portability
This projector is quite compact in size and weight. Having a sophisticated shape like an attaché case with a retractable carrying handle, the projector will help you make powerful presentation wherever you go.
Laser Pointer Function
The Remote Control Unit of this projector has the Laser Pointer function providing convenience and smartness for your presentations.
Other Features
This projector has Motor Zoom/Focus, No Show, Picture Freeze, Keystone and Mute functions. And the Air Pad Remote Control is equipped.
Accessories
This projector comes with the parts listed below. Check to make sure all are included. If any parts are missing, contact to a sales dealer.
●Owner's Manual.
●AC Power Cord.
●Wireless Remote Control Unit.
●Batteries for Remote Control Unit.
●VGA Cable.
●Control Cable for PS/2 Port.
●Lens Cover.
●Dust Cover
5
PREPARATION
NAME OF EACH PART OF THE PROJECTOR
FRONT OF THE CABINET
PROJECTION LENS
LENS COVER
INFRARED REMOTE RECEIVER
BACK OF THE CABINET
EXHAUST VENT
HOT AIR EXHAUSTED !
Air blown from the exhaust vent is hot. When using or installing the projector, following attention should be taken.
● Do not put a flammable object near this part.
●Keep heat-sensitive objects away from the exhaust vent.
●Do not touch this part especially screws and metallic parts. This part will become hot while the projector is used.
POWER CORD CONNECTOR
BOTTOM OF THE CABINET
AIR INTAKE VENTS
These Air Intake Vents should not be blocked.
CARRY HANDLE
SPEAKER (Monaural)
INFRARED
REMOTE RECEIVER
ADJUSTABLE FEET
AND
FEET LOCK LATCHES
LAMP COVER
6
PREPARATION
SETTING-UP THE PROJECTOR
POSITIONING THE PROJECTOR
●This projector is basically designed to project on a flat projection surface.
●The projector can be focused from 1.4m ~ 10.8m.
●Refer to the figure below to adjust the screen size.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
10.8m |
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
7.3m |
|
|
|
300” |
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5.5m |
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
3.6m |
|
|
|
200” |
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
1.4m |
|
|
|
100” |
|
150” |
|
|
154” |
|
|
|
231” |
|
|
H1 |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
40” |
|
|
115” |
|
|
|
|
|
|||||||||||||||
|
|
|
|
|
|
|
|
77” |
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
H2 |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
30” |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
Screen Size |
|
30” |
|
|
|
|
60” |
|
|
|
|
100” |
|
|
|
150” |
|
|
200” |
300” |
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(W x H) mm |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
610 x 457 |
|
|
|
1219 x 914 |
|
2032 x 1524 |
|
|
|
3048 x 2286 |
|
|
4064 x 3048 |
6096 x 4572 |
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Height (H1) |
435mm |
|
|
|
|
870mm |
|
|
|
|
1451mm |
|
|
|
2177mm |
|
|
2903mm |
4354mm |
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Height (H2) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
22mm |
|
|
|
|
44mm |
|
|
|
|
73mm |
|
|
|
109mm |
|
|
145mm |
218mm |
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ROOM LIGHT
The brightness in the room has a great influence on the picture quality. It is recommended to limit ambient lighting in order to provide the best image.
ADJUSTABLE FEET
Picture tilt and projection angle can be adjusted by rotating the ADJUSTABLE FEET. Projection angle can be adjusted to 10 degrees.
1 |
Lift the front of the projector and pull the FEET LOCK |
LATCHES on both sides of the projector. |
|
2 |
Release the FEET LOCK LATCHES to lock the |
ADJUSTABLE FEET and rotate the ADJUSTABLE |
|
|
FEET for fine tune of the position and the tilt. |
3 |
To shorten the ADJUSTABLE FEET, lift the front of the |
projector and pull and undo the FEET LOCK LATCHES. |
The position and the keystone distortion of the image can be also adjusted with the Menu Operation. (Refer to pages 20, 28 and 29.)
ADJUSTABLE FEET
FEET LOCK LATCHES
7
PREPARATION
CONNECTING THE AC POWER CORD
This projector uses nominal input voltages of 200 - 240 V AC. The projector automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system.
Consult your authorized dealer or service station if your are not sure of the type of power supply being in use. Connect the projector with the peripheral equipment before turning the projector on. (Refer to pages 10 ~ 13 for connection.)
CAUTION
For the safety, unplug the AC Power Cord when the appliance is not used.
When this projector is connected to the outlet with the AC Power Cord, the appliance is in Stand-by Mode and consumes a little electric power.
Connect the AC power supply cord (supplied) to the projector.
The socket-outlet must be near this equipment and must be easily accessible.
VENTILATION
This projector is equipped cooling fans for protection from overheating. ensure the ventilation and avoid a possible risk of fire and malfunction.
●Do not cover the vent slot.
●Keep the rear grill at least one meter away from any object.
●Make sure that there is no object on both sides of the projector. Those obstacles may prevent the projector from taking the cooling air through the side Air Intake Vent Slots.
Pay attention to the following to
EXHAUST VENT
(REAR SIDE)
AIR INTAKE VENTS (BOTH SIDES)
8
PREPARATION
MOVING THE PROJECTOR
Use the Carry Handle when moving the Projector.
When moving the projector, replace the lens cover and rotate the feet fully clockwise (to shorten the feet) to prevent from damage to the lens and the cabinet.
When this projector is not used for the extended period, replace the lens cover, tuck the Adjustable Feet and apply the dust cover supplied to this projector.
CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR
●Do not drop or give a shock to the projector, otherwise damages or malfunctions may result.
●When carrying the projector, use a carrying case recommended by Sanyo.
●Do not transport the projector by using a courier or transport service in an unsuitable transport case. This may cause damage to the projector. To transport the projector through a courier or transport service, use a case recommended by Sanyo.
●For carrying or transportation cases, contact a Sanyo authorized dealer.
9
CONNECTING THE PROJECTOR
TERMINALS OF THE PROJECTOR
S-VIDEO INPUT JACK
Connect the S-VIDEO output from the video equipment to this terminal.
(Refer to P11.)
AUDIO INPUT JACKS
Connect the audio outputs from the video equipment to these terminals.
(Refer to P11.)
● When the audio output is monaural, connect it to the Left jack.
COMPUTER INPUT TERMINAL
Connect the computer output to this terminal.
(Refer to P12, 13.)
MONITOR OUTPUT TERMINAL
This terminal outputs the signal from the COMPUTER IN terminal. Connect to the monitor to this terminal.
(Refer to P12, 13.)
S-VIDEO |
|
||
R-AUDIO-L(MONO) |
VIDEO |
AUDIO |
|
IN |
|||
|
|
||
|
|
OUT |
|
COMPUTER IN |
|
|
MONITOR OUT
CONTROL PORT
VIDEO INPUT JACK
Connect the video output from the video equipment to this terminal.
(Refer to P11.)
COMPUTER AUDIO INPUT JACK
Connect the audio output from the computer to this terminal. (Refer to P12, 13.)
AUDIO OUTPUT JACK (STEREO)
Connect the audio amplifier to this terminal.
(Refer to P11, 12, 13.)
CONTROL PORT CONNECTOR
When controlling the computer with the Remote Control of this projector, connect the mouse port of your personal computer to this terminal.
(Refer to P12, 13.)
COMPUTER INPUT / MONITOR OUTPUT TERMINAL
Terminal : HDB15-PIN
Connect the display output terminal of the computer to COMPUTER INPUT terminal of thus projector with the VGA Cable (supplied). And connect to the monitor to MONITOR OUTPUT with the monitor cable (not supplied). When connecting the Macintosh computer, the MAC Adapter (not supplied) is required.
Pin Configuration |
|
1 |
Red Input |
9 |
Non Connect |
|||
|
2 |
Green Input |
10 |
Ground (Vert.sync.) |
||||
|
|
|
|
|
||||
|
|
|
|
|
3 |
Blue Input |
11 |
Sense 0 |
5 |
4 |
3 |
2 |
1 |
4 |
Sense 2 |
12 |
Sense 1 |
10 |
9 |
|
8 |
7 6 |
5 |
Ground (Horiz.sync.) |
13 |
Horiz. sync. |
15 |
14 |
13 |
12 |
11 |
6 |
Ground (Red) |
14 |
Vert. sync. |
|
|
|
|
|
||||
|
|
|
|
|
7 |
Ground (Green) |
15 |
Reserved |
|
|
|
|
|
8 |
Ground (Blue) |
|
|
CONTROL PORT CONNECTOR
Terminal : Mini DIN 8-PIN
Connect control port (PS/2, Serial or ADB port) on your computer to this terminal with the Control Cable (the Control Cable for PS/2 port is supplied).
Pin Configuration |
|
|
PS/2 |
Serial |
ADB |
||
|
1 |
----- |
R X D |
----- |
|||
|
|
|
|
||||
|
|
|
|
2 |
CLK |
----- |
ADB |
8 |
7 |
6 |
|
3 |
DATA |
----- |
----- |
|
4 |
GND |
GND |
GND |
|||
5 |
4 |
3 |
|
||||
2 |
1 |
|
|
5 |
----- |
RTS |
----- |
|
|
|
|
6 |
----- |
T X D |
----- |
|
|
|
|
7 |
GND |
GND |
----- |
|
|
|
|
8 |
----- |
GND |
GND |
10
CONNECTING THE PROJECTOR
CONNECTING TO THE VIDEO EQUIPMENT
Video Source (example) |
|
Video Cassette Recorder |
Video Disc Player |
Used cables for connection
•VIDEO CABLE
•S-VIDEO CABLE
•AUDIO CABLE (stereo)
These cables are not supplied with this projector.
Video / Audio Output |
S-VIDEO Output |
||
|
|
|
|
|
|
|
|
Video Audio Cable |
S-VIDEO Cable |
S-VIDEO |
|
||
R-AUDIO-L(MONO) |
VIDEO |
AUDIO |
|
IN |
|||
|
|
OUT
COMPUTER IN
MONITOR OUT
Use the either of VIDEO jack or S-VIDEO jack. When the both jacks are connected, the S-VIDEO jack has priority over the VIDEO jack.
Terminals
of the Projector
CONTROL PORT
NOTE :
When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.
Audio Cable (Stereo)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
External Audio Equipment |
Audio Input |
|||||
|
|
|||||
|
|
|
|
|||
|
Audio Speaker |
|
|
|||
|
(stereo) |
Audio Amplifier |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
11
CONNECTING THE PROJECTOR
CONNECTING TO THE COMPUTER
To connect with the computer, refer to the figure below.
Used cables for connection
•VGA CABLE
•CONTROL CABLE FOR PS/2 PORT
•CONTROL CABLE FOR SERIAL PORT,or ADB PORT
•MAC ADAPTER
•MONITOR CABLE
•PC AUDIO CABLE (stereo)
These cables are not supplied with this projector.
IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA / SXGA)
Desktop type
Laptop type
Monitor
Audio Speaker
(stereo)
Audio Amplifier
To each terminal of your computer
To the Monitor |
Monitor Output |
Serial port PS/2 port |
MAC Adapter |
Set the slide
ON |
DIP |
switches following |
1 2 |
3 4 5 6 |
the chart on the |
next page.
Terminal |
Terminal |
ADB port Audio Output |
Audio Input |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Terminal
Audio Cable (stereo)
Control Cable for ADB Port
Control Cable for PS/2 Port
Control Cable for Serial Port
VGA Cable
Monitor Cable
NOTE :
When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.
12