Sanyo PLC-XU116 - 4500 Lumens, PLC-XU116 User Manual

Download

Page 1

EXPAND SERIAL COMMAND

FUNCTIONAL SPECIFICATIONS

PLC-XU116

Ver. 1.00

SANYO Electric Co., Ltd DS Company Projector Division

Page 2

- CONTENTS -

1.	Ove	erview	8
2.	Ser	rial Interface Specification	8
2	2.1	Transfer Specification	8
2	2.2	Connection	8
3.	Not	tes for communication	9
4.	Nar	me Definition	9
5.	Fur	nctional Execution Command Table1	0
5	5.1	Image Command Table1	0
5	5.2	PC Adjust Control Command Table 1	0
5	5.3	Input Control Command Table 1	0
5	5.4	Screen Command Table1	1
5	5.5	Lamp Command Table1	1
5	5.6	Sound Command Table1	1
5	5.7	Setting Command Table1	1
5	5.8	Other Command Table 1	2
6.	Sta	tus Read Command Table1	3
6	5.1	Image Status Read Command Table1	3
6	5.2	PC Adjust Status Read Command Table 1	3
6	5.3	Video Status Read Command Table1	3
6	6.4	Input Status Read Command Table1	3
6	5.5	Screen Status Read Command Table 1	4
6	6.6	Lamp Status Read Command Table1	4
6	5.7	Sound Status Read Command Table 1	4
6	6.8	Setting Status Read Command Table 1	4
6	5.9	Other Status Read Command 1	5
7.	Erre	or Code Table 1	6
8.	Fur	nctional Execution Command1	7
8	8.1	Format1	7
8	3.2	Transfer Example 1	7
8	3.3	Operation Requirements 1	7
8	8.4	Image Command 1	8
	8.4.	.1 CF_BRIGHT Command 1	8
	8.4.	.2 CF_CONT Command 1	8
	8.4.	.3 CF_COLOR Command 1	8
	8.4.	.4 CF_TINT Command 1	8
	8.4.	.5 CF_SHARP Command1	9
	8.4.	.6 CF_GAMMA Command 1	9
	8.4.	.7 CF_WBAL - Command1	9
	8.4.	.8 CF COLTEMP Command	0

Page 3

8.4.9	CF_PROGV Command	. 20
8.4.10	CF_NZRED Command	. 20
8.4.11	CF_IMAGE Command	. 21
8.4.12	CF_IMAGEADJ Command	. 21
8.5 PC	Adjust Control Command	. 22
8.5.1	CF_FSYNC Command	. 22
8.5.2	CF_TDOTS Command	. 22
8.5.3	CF_CLAMP Command	. 22
8.5.4	CF_H – POS Command	. 23
8.5.5	CF_V – POS Command	. 23
8.5.6	CF_DDOTS Command	. 23
8.5.7	CF_DLINE Command	. 24
8.5.8	CF_PCSTORE Command	. 24
8.5.9	CF_PCMODEFREE Command	. 24
8.6 Inp	out Control Command	. 25
8.6.1	CF_INPUT Command	. 25
8.6.2	CF_SOURCE Command	. 25
8.6.3	CF_INPUT1 Command	. 26
8.6.4	CF_INPUT2 Command	. 26
8.6.5	CF_INPUT3 Command	. 26
8.6.6	CF_INPUT4 Command	. 26
8.6.7	CF_INPUT5 Command	. 26
8.6.8	CF_INPUT_%1_%2 Command	. 27
8.6.9	CF_SYSTEM Command	. 28
8.7 Sc	reen Control Command	. 29
8.7.1	CF_SCREEN Command	. 29
8.7.2	CF_DZCENT Command	. 29
8.7.3	CF_KEYSTONE Command	. 30
8.7.4	CF_KYSTNMODE Command	. 30
8.7.5	CF_CORNER-UL Command	. 30
8.7.6	CF_CORNER-UR Command	. 31
8.7.7	CF_CORNER-DL Command	. 31
8.7.8	CF_CORNER-DR Command	. 31
8.7.9	CF_CORNERTESTPAT Command	. 32
8.7.10	CF_VSCALE Command	. 32
8.7.11	CF_VPOS Command	. 33
8.7.12	CF_HSCALE Command	. 33
8.7.13	CF_HPOS Command	. 34
8.8 Lai	mp Command	. 35
8.8.1	CF LAMPH Command	35

Page 4

	8.8.2	CF_LAMPMODE Command	35
8.	.9 Sou	and Command	36
	8.9.1	CF_VOLUME Command	36
	8.9.2	CF_MUTE Command	36
8.	.10 Set	ting Command	37
	8.10.1	CF_LANG Command	37
	8.10.2	CF_MENUPOSITION Command	37
	8.10.3	CF_AUTOSETUPPCADJ Command	37
	8.10.4	CF_AUTOSETUPKEYSTONE Command	38
	8.10.5	CF_INPUTSEARCH Command	38
	8.10.6	CF_AUTOSETUP	38
	8.10.7	CF_BACKGND Command	38
	8.10.8	CF_DISP Command	39
	8.10.9	CF_LOGO Command	39
	8.10.10	CF_USBTERMINAL Command	40
	8.10.11	CF_CEIL Command	40
	8.10.12	CF_REAR Command	40
	8.10.13	CF_POINTER Command	40
	8.10.14	CF_P-MANE Command	41
	8.10.15	CF_P-MANETIME Command	41
	8.10.16	CF_ON-STA Command	41
	8.10.17	CF_STANDBYMODE Command	41
	8.10.18	CF_CCAPTIONDISP Command	42
	8.10.19	CF_CCAPTIONCOLOR Command	42
	8.10.20	CF_RCODE Command	42
	8.10.21	CF_KEYDIS Command	43
	8.10.22	CF_PJPINCODE Command	43
	8.10.23	CF_FANMODE Command	43
	8.10.24	CF_FANCONTROL Command	44
	8.10.25	CF_FILTIMER Command	44
	8.10.26	CF_FILH Command	44
	8.10.27	CF_FDEFAULT Command	44
8.	.11 Oth	er Command	45
	8.11.1	CF_KEYENU Command	45
	8.11.2	CF_MENU Command	45
	8.11.3	CF_POWER Command	45
	8.11.4	CF_FREEZE Command	46
	8.11.5	CF_VMUTE Command	46
	8.11.6	CF_PTIMER Command	46
9.	Status F	Read Command	47

Page 5

9.1	0.1 Format
9.2	0.2 Transfer Example 47
9.3	Оре	eration Condition	47
9.4	Ima	ge Status Read Command	48
9.4	.1	CR_BRIGHT Command	48
9.4	.2	CR_CONT Command	48
9.4	.3	CR_COLOR Command	48
9.4	.4	CR_TINT Command	48
9.4	.5	CR_SHARP Command	48
9.4	.6	CR_GAMMA Command	49
9.4	.7	CR_WBAL – R Command	49
9.4	.8	CR_WBAL – G Command	49
9.4	.9	CR_WBAL – B Command	49
9.4	.10	CR_COLTEMP Command	49
9.4	.11	CR_NZRED Command	50
9.4	.12	CR_PROGV Command	50
9.4	.13	CR_IMAGE Command	50
9.4	.14	CR_IMGGMD Command	50
9.5	PC	Adjust Status Read Command	51
9.5	5.1	CR_FSYNC Command	51
9.5	.2	CR_TDOTS Command	51
9.5	.3	CR_CLAMP Command	51
9.5	.4	CR_H – POS Command	51
9.5	.5	CR_V – POS Command	52
9.5	.6	CR_DDOTS Command	52
9.5	.7	CR_DLINE Command	52
9.5	.8	CR_PCSTORE Command	52
9.6	Vide	eo Status Read Command	53
9.6	5.1	CR_SERSYS Command	53
9.7	Inpu	ut Status Read Command	54
9.7	.1	CR_INPUT Command	54
9.7	.2	CR_SOURCE Command	54
9.7	.3	CR_SRCINP1 Command	54
9.7	.4	CR_SRCINP2 Command	54
9.7	.5	CR_SRCINP3 Command	54
9.7	.6	CR_SRCINP4 Command	55
9.7	.7	CR_SRCINP4 Command	55
9.7	.8	CR_SYSTEM Command	56
9.7	.9	CR_SYSLIST Command	57
9.7	.10	CR_MODELIST Command	57

Page 6

9.8 Sc	reen Status Read Command	. 58
9.8.1	CR_SCREEN Command	. 58
9.8.2	CR_KYSTNMODE Command	. 58
9.8.3	CR_ CORNERTESTPAT Command	. 58
9.8.4	CR_VSCALE Command	. 58
9.8.5	CR_VPOS Command	. 59
9.8.6	CR_HSCALE Command	. 59
9.8.7	CR_HPOS Command	. 59
9.9 La	mp Status Read Command	. 60
9.9.1	CR_LAMPREPL Command	. 60
9.9.2	CR_LAMPH Command	. 60
9.9.3	CR_LAMPCORRESPH Command	. 60
9.9.4	CR_LAMPMODE Command	. 60
9.9.5	CR_LAMPMSTS Command	. 61
9.9.6	CR_PROJH Command	. 61
9.9.7	CR_HMLAMP Command	. 61
9.10 So	und Status Read Command	. 62
9.10.1	CR_VOLUME Command	. 62
9.10.2	CR_MUTE Command	. 62
9.11 Se	tting Status Read Command	. 63
9.11.1	CR_LANG Command	. 63
9.11.2	CR_AUTOSETUPPCADJ Command	. 63
9.11.3	CR_AUTOSETUPKEYSTONE Command	. 63
9.11.4	CR_INPUTSEARCH Command	. 63
9.11.5	CR_BACKGND Command	. 64
9.11.6	CR_DISP Command	. 64
9.11.7	CR_LOGO Command	. 64
9.11.8		. 64
9.11.9	CR_CEIL Command	. 64
9.11.10	CR_REAR Command	. 65
9.11.11	CR_POINTER Command	. 65
9.11.12	CR_P-MANE Command	. 65
9.11.13	CR_P-MANETIME Command	. 65
9.11.14	CR_ON-STA Command	. 65
9.11.15	CR_STANDBYMODE Command	. 66
9.11.16	CR_CCAPTIONDISP Command	. 66
9.11.17	CF_CCAPTIONCOLOR Command	. 66
9.11.18	CR_RCODE Command	. 66
9.11.19	CR_SECURITY Command	. 66
9.11.20	CR_KEYDIS Command	. 67

Page 7


67	21 CR_PJLOCKNOW Command	9.11.21
67	22 CR_PJLOCKMENU Command	9.11.22
	23 CR_FANMODE Command	9.11.23
	24 CR_FANCONTROL Command	9.11.24
68	25 CR_FILH Command	9.11.25
68	26 CR_FILREPL Command	9.11.26
68	27 CR_FILTIMER Command	9.11.27
69	Other Status Read Command	9.12 Oth
69	1 CR_STATUS Command	9.12.1
69	2 CR_SIGNAL Command	9.12.2
69	3 CR_VMUTE Command	9.12.3
69	4 CR_FREEZE Command	9.12.4
	5 CR_PTIMER Command	9.12.5
	6 CR_TEMPWARN Command	9.12.6
71	7 CR_TEMP Command	9.12.7
	8 CR TEMPFAIL Command	9.12.8

Page 8

1. Overview

1.1 This Functional Specification defines communication functions for PLC-XU116.
1.2 Compatible to Firmware Ver. 1.x of the projector.
1.3 Most commands can be used to control projector remotely from PC by RS-232C. Therefore, the commands are defined as Expand Serial Commands.

2. Serial Interface Specification

2.1 Transfer Specification

ltem	Specification
Synchronous System	Asynchronous
Transmission Speed	9600 / 19200
Data Length	8 bit
Parity	N/A
Stop Bit	1
Flow Control	N/A

Note1) Transmission Speed : initial setting value is 19200

Note2) Transmission Speed can be changed in service mode.

2.2 Connection

Dedicated serial cable must be used for a connection to a computer and a projector.

Page 9

3. Notes for communication

1. Expand Serial Command is defined as one command / one line that starts with "C" and ends with carriage return (0x0D)
2. There are two types of commands: Functional Execution Command and Status Read Command.

- Example of Functional Execution Command:"CF BRIGHT 032"[CR]

- Example of Status Read Command: "CR RIGHT" [CR]

Note) " " means a space

3. When it takes more than one second to receive one command, it is not executed.

When it takes more than one second to receive carriage return (0X0D) after the projector receives the first data "C". it clears the information of buffer.

4. On command pipelining, wait for the interval of 100ms till sending next command after receiving a response.

When a computer sends next command before receiving a response, the projector may not operate properly except when there is no response for more than 5 seconds.

5. It takes about 5 seconds for internal initialization after plugging in AC power. During this time commands cannot be processed. Do not issue any command.

4. Name Definition

1. Data from a controller to a projector is represented as COMMAND, and data from a projector to a controller for the incoming command is represented as RESPONSE.
2. [CR] : Carriage Return Code

Command ends with cartridge return code.

Response also ends with carriage return code.

3. _: Space Code

A space Code is indicated by (_).

4. %1 : Parameter in Command

When there are several parameters, they are defined as %2, %3...

5. %%% : Error code returned from a projector

Acceptable: "000".

Unacceptable: See [7. Error Code Table].

6. %a : Parameter in Response Command

When there are several parameters, they are defined as %b, %c...

Page 10

5. Functional Execution Command Table

5.1 Image Command Table

Execute command	ltem
CF_BRIGHT_%1[CR]	Set Brightness value
CF_CONT_%1[CR]	Set Contrast value
CF_COLOR_%1[CR]	Set Color value
CF_TINT_%1[CR]	Set Tint value
CF_SHARP_%1[CR]	Set Sharpness value
CF_GAMMA_%1[CR]	Set Gamma value
CF_WBAL-R_%1[CR]	Set White Balance Red value
CF_WBAL-G_%1[CR]	Set White Balance Green value
CF_WBAL-B_%1[CR]	Set White Balance Blue value
CF_COLTEMP_%1[CR]	Set Color Temp. value
CF_PROGV_%1[CR]	Set /Cancel Progressive Scan
CF_NZRED_%1[CR]	Set/Cancel Noise reduction
CF_IMAGE_%1[CR]	Set Image mode
CF_IMAGEADJ_%1[CR]	Reset/Store for Image Adjustment

5.2 PC Adjust Control Command Table

Execute command	Item
CF_FSYNC_%1[CR]	Set Fine Sync value
CF_TDOTS_%1[CR]	Set Total Dots value
CF_CLAMP_%1[CR]	Set Clamp Value
CF_H-POS_%1[CR]	Set Horizontal Position value
CF_V-POS_%1[CR]	Set Vertical Position value
CF_DDOTS_%1[CR]	Set Display Dots value
CF_DLINE_%1[CR]	Set Display Line value
CF_PCSTORE_%1[CR]	Store current values of PC Adjust at Mode 1-5
CF_PCMODEFREE_%1[CR]	Relese registered values of Mode1-5.

5.3 Input Control Command Table

Execute command	ltem
CF_INPUT_%1[CR]	Select Input
CF_SOURCE_%1[CR]	Select Input Source
CF_INPUT1 _%1[CR]	Select computer-1 and set Input selected in %1
CF_INPUT2_%1[CR]	Select computer-2 and set Input selected in %1
CF_INPUT3_%1[CR]	Select Video and set Input selected in %1
CF_INPUT4_%1[CR]	Select S-video and set Input selected in %1
CF_INPUT5_%1[CR]	Select Network and set Input selected in %1
CF_INPUT_%1_%2[CR]	Select Input and Source
CF_SYSTEM_%1[CR]	Select System

Page 11

5.4 Screen Command Table

Execute command	ltem
CF_SCREEN_%1[CR]	Select Screen size
CF_DZCENT_%1[CR]	Cancel Digital Zoom mode
CF_KEYSTONE_%1[CR]	Set Keystone
CF_KYSTNMODE_%1[CR]	Set Keystone Store mode
CF_CORNER-UL_%1[CR]	Correct top-left corner
CF_CORNER-UR_%1[CR]	Correct top-right corner
CF_CORNER-DL_%1[CR]	Correct bottom-left corner
CF_CORNER-DR_%1[CR]	Correct bottom-right corner
CF_CORNERTESTPAT_%1[CR]	Select test pattern for Corner correction.
CF_VPOS_%1[CR]	Set value of Vertical position
CF_HSCALE_%1[CR]	Set value of Horizontal scale
CF_HPOS_%1[CR]	Set value of Horizontal position

5.5 Lamp Command Table

Execute command	ltem
CF_LAMPH_%1[CR]	Reset Lamp use time
CF_LAMPMODE_%1[CR]	Select Lamp mode

5.6 Sound Command Table

Execute command	ltem
CF_VOLUME_%1[CR]	Set Volume value
CF_MUTE_%1[CR]	Control ON/OFF of Sound Mute

5.7 Setting Command Table

Execute command	ltem
CF_LANG_%1[CR]	Select language for OSD
CF_MENUPOSITION_%1[CR]	Move menu position.
CF_AUTOSETUPPCADJ_%1 [CR]	Set Auto PC in Auto Setup
CF_AUTOSETUPKEYSTONE_%1 [CR]	Set Auto Keystone in Auto Setup
CF_INPUTSEARCH_%1[CR]	Set up Input search function
CF_AUTOSETUP_%1[CR]	Excute Auto Setup
CF_BACKGND_%1[CR]	Set screen mode for the case of no signal
CF_DISP_%1[CR]	Set Display function
CF_LOGO_%1_%2[CR]	Set Logo function
CF_USBTERMINAL_%1[CR]	Switch usage of USB terminal
CF_CEIL_%1[CR]	Set Ceiling function
CF_REAR_%1[CR]	Set Rear function
CF_POINTER_%1[CR]	Set Pointer mode
CF_P-MANE_%1[CR]	Set Power management function
CF_P-MANETIME_%1[CR]	Set Power management time
CF_ON-STA_%1[CR]	Set Power ON Start function
CF_STANDBYMODE_%1[CR]	Set Standby Mode
CF_CCAPTIONDISP_%1[CR]	Set channel of Closed caption
CF_CCAPTIONCOLOR_%1[CR]	Set color of Closed caption
CF_RCODE_%1[CR]	Select Remote Control Reception Code
CF_KEYDIS_%1[CR]	Disable RC/Projector keys
CF_PJPINCODE_%1[CR]	Input PIN code to release PJ Locj
CF_FANMODE_%1[CR]	Select Fan mode
CF_FANCONTROL_%1[CR]	Select Fan control mode
CF_FILTIMER_%1[CR]	Set time when Filter warning OSD is displayed
CF_FILH_%1[CR]	Reset Filter used time
CF_FDEFAULT_%1[CR]	Set the value to Factory Default

Page 12

5.8 Other Command Table

Execute command	Item
CF_KEYEMU_%1[CR]	Behave the same as corresponding key of projector top panel
CF_MENU_%1[CR]	Switch ON/OFF of each Menu.
CF_POWER_%1[CR]	Switch ON/OFF of Power.
CF_FREEZE _%1[CR]	Set Freezefunction.
CF_VMUTE _%1[CR]	Set No show function.
CF_PTIMER _%1[CR]	Set P-Timer function.

Page 13

6. Status Read Command Table

6.1 Image Status Read Command Table


Status read command	Item
CR_BRIGHT[CR]	Get Brightness value
CR_CONT[CR]	Get Contrast value
CR_COLOR[CR]	Get Color value
CR_TINT[CR]	Get Tint value
CR_SHARP[CR]	Get Sharpness value
CR_GAMMA[CR]	Get Gamma value
CR_WBAL-R[CR]	White Balance Red value
CR_WBAL-G[CR]	White Balance Green value
CR_WBAL-B[CR]	White Balance Blue value
CR_COLTEMP[CR]	Get setting value of Color temperature
CR_NZRED[CR]	Get setting status of Noise reduction
CR_PROGV[CR]	Get setting status of Progressive scan
CR_IMAGE[CR]	Get Selected Image status
CR_IMGGMD[CR]	Get setting value of Image Gamma

6.2 PC Adjust Status Read Command Table

Status read command	Item
CR_FSYNC[CR]	Get setting value of Fine Sync
CR_TDOTS[CR]	Get setting value of Total Dots
CR_CLAMP[CR]	Get setting value of Clamp
CR_H-POS[CR]	Get setting value of Horizontal Position
CR_V-POS[CR]	Get setting value of Vertical Position
CR_DDOTS[CR]	Get setting value of Display Dots
	Get setting value of Display Line
CR_PCSTORE[CR]	Get Free or Stored status for PC Adj. mode1-5

6.3 Video Status Read Command Table

Status read command	Item
	Get selected current signal. When in Auto mode, it
	returns a result by Auto detect.

6.4 Input Status Read Command Table

Status read command	Item
CR_INPUT[CR]	Get selected Input No.
CR_SOURCE[CR]	Get selected source of currently selected Input
CR_SRCINP1[CR]	Get selected source of Computer 1
CR_SRCINP2[CR]	Get selected source of Computer 2
CR_SRCINP3[CR]	Get selected source of Video
CR_SRCINP4[CR]	Get selected source of S-video
CR_SRCINP5[CR]	Get selected source of Network
CR_SYSTEM[CR]	Get selected system status in Input mode
CR_SYSLIST[CR]	Get selectable System table
CR_MODELIST[CR]	Get selectable Mode table

Page 14

6.5 Screen Status Read Command Table

Status read command	ltem
CR_SCREEN[CR]	Get selected screen size
CR_KYSTNMODE[CR]	Get setting status of Keystone Store mode
CR_CORNERTESTPAT[CR]	Get setting status of Test pattern for Coner correction.
CR_VSCALE[CR]	Get setting status of Vertical Scale
CR_VPOS[CR]	Get setting status of Vertical Position
CR_HSCALE[CR]	Get setting status of Horizontal Scale
CR_HPOS[CR]	Get setting status of Horizontal Position

6.6 Lamp Status Read Command Table

Status read command	Item
CR_LAMPREPL[CR]	Get the information for Lamp replacement time
CR_LAMPH[CR]	Get lamp total running time
CR_LAMPCORRESPH[CR]	Get corresponding lamp use time
CR_LAMPMODE[CR]	Get Lamp Mode status
CR_LAMPSTS[CR]	Get lamp lighting status
CR_PROJH[CR]	Get projector total running time
CR_HMLAMP[CR]	Get lamp number

6.7 Sound Status Read Command Table

Status read command	Item
CR_VOLUME[CR]	Get Volume value
CR_MUTE[CR]	Get Sound Mute setting status

6.8 Setting Status Read Command Table

Status read command	ltom
Status read command	item
CR_LANG[CR]	Get selected language
CR_AUTOSETUPPCADJ	Get setting status of Auto PC in Auto setup
	Get setting status of Keystone in Auto setup
CR_INPUTSEARCH[CR]	Get setting status of Input search
	Get setting status screen mode for the case of no
	signal
CR_DISP[CR]	Get setting status of Display
CR_LOGO[CR]	Get setting status of Logo
CR_USBTERMINAL[CR]	Get setting status of USB terminal
CR_CEIL [CR]	Get setting status of Ceiling
CR_REAR[CR]	Get setting status of Rear
	Get setting status of Pointer
CR_P-MANE[CR]	Get setting status of Power management
CR_P-MANETIME[CR]	Get setting time for Power management
CR_ON-STA[CR]	Get setting status of ON Start
CR_STANDBYMODE[CR]	Get setting status of Standby Mode
CR_CCAPTIONDISP[CR]	Get setting status of channel of Closed caption
CR_CCAPTIONCOLOR[CR]	Get setting status of color of Closed caption
CR_RCODE[CR]	Get selected Remote Control Code
CR_SECURITY[CR]	Get setting status of Security
CR_KEYDIS[CR]	Get RC/KEY disability status
CR_PJLOCKNOW[CR]	Get if PJ Lock is actually in operation
CR_PJLOCKMENU[CR]	Get setting statsus of PJ Lock on Menu
CR_FANMODE[CR]	Get selected Fan mode
CR_FANCONTROL[CR]	Get selected Fan Control Mode
CR_FILH[CR]	Get Filter used time
CR_FILREPL[CR]	Get the information for Filter replacement time
CR_FILTIMER[CR]	Get time when Filter warning OSD is displayed

Page 15

6.9 Other Status Read Command

Status read command	Item
CR_STATUS[CR]	Get setting status of Projector behavior
CR_SIGNAL[CR]	Get Signal Status if there is a signal or not
CR_VMUTE[CR]	Get setting status of No Show
CR_FREEZE[CR]	Get setting status of Freeze
CR_PTIMER[CR]	Get the operating status of Presentation Timer
CR_TEMPWARN[CR]	Get if temperature is close to abnormal temperature
CR_TEMP[CR]	Get current temperature status
CR_TEMPFAIL[CR]	Get temperature when sensors approach abnormal temperature

Page 16

7. Error Code Table

Error Code	Contents
?	-When the received data cannot be decoded -Parameter determination error (digit number error, including invalid value, etc.)
101	The function is not available in the selected Mode
102	Selected value is out of range (Not reflected)
103	Command mismatched to Hardware (command for Optional function which is not installed)
201	When reached upper or lower limit of increasing or decreasing data
301	Command cannot be executed during capturing display. Resend the command after a while
302	Command cannot be executed during Auto PC operation. Resend the command after a while
303	Command cannot be executed while Memory Card Viewer is in process. Resend the command after a while
402	Command cannot be executed during PIN code operation. Resend the command after a while.

Note) These error codes are applied to Expand Command, not to Basic Command

Page 17

8. Functional Execution Command

8.1 Format

1. PC issues commands in format as below:

%1 : Parameter (Character line)

: Space (To separate COMMAND and Parameter)

2. The projector decodes the received command and when it is ready to receive the next

command, it returns the response.

"000" [CR] : (0x06. 0x0D) When receiving Functional Execution Command

"nnn" [CR] : Except "000", when it is unable to execute command by any specific reason.

See Error Code Table for details

3. When the received data cannot be decoded, the projector returns "?" [CR]

8.2 Transfer Example

When setting projector's total dots to 1344 by Expand Serial Command

PC → PJ: "CF_TDOTS_1344" [CR]

PC ← PJ: "000"[CR] - Acceptable

8.3 Operation Requirements

1. Functional Execution Command is limited when the projector status is as below.

However, Status Read Command is effective even under these conditions.

Projector Status	Available Functional Execution Command
Standby	C00: POWER ON
Countdown in process	C00: POWER ON (Terminates Countdown) C01: POWER OFF C02: POWER OFF (Terminates Countdown)
Cooling down in process	N/A
Cooling down in process due to Abnormal Temperature	N/A
Abnormal Temperature	N/A
Power Failure (For 60 seconds after Power Failure occurred)	N/A
Power Save / Cooling down in process	N/A
Power Save in process	C00: POWER ON C01: POWER OFF

Note:) When the projector receives the other command in this above status, it returns error code

to show the status.

When the projector receives the following functional execution commands, OSD menu is closed

except for pop-up menu

2. Functional Execution Commands are invalid when projector is in standby under Eco mode

Page 18

8.4 Image Command

8.4.1 CF BRIGHT Command

Command	"CF_BRIGHT_%1"[CR]
%1	"000~063" Directly select Brightness setting value "UP" Current Brightness setting value + 1 "DN" Current Brightness setting value – 1
Details	Set Brightness value of user control The value set by this command will not be saved to projector. Therefore, when turning into Stanby status or ALL is OFF, the value returns to original setting. (The value is held in Suspend mode.) This command is available in normal Power ON status.
Bosponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.4.2 CF_CONT Command

Command	"CF_CONT_%1"[CR]
%1	"000~063" Directly select Contrast setting value "UP" Current Contrast setting value + 1 "DN" Current Contrast setting value – 1
Details	Set Contrast value of user control The value set by this command will not be saved to projector. Therefore, when turning into Stanby status or ALL is OFF, the value returns to original setting. (The value is held in Suspend mode.) This command is available in normal Power ON status.
Acceptable		"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.4.3 CF_COLOR Command


Command	"CF_COLOR_9	"CF_COLOR_%1"[CR]
%1	"000~063" Directly select Color setting value "UP" Current Color setting value + 1 "DN" Current Color setting value - 1
Details	Set Color value of user control The value set by this command will not be saved to projector. Therefore, when turning into Stanby status or ALL is OFF, the value returns to original setting. (The value is held in Suspend mode.) This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.4.4 CF_TINT Command

Command	"CF_TINT_%1"[CR]
%1	"000~063" Directly select Tint setting value "UP" Current Tint setting value + 1 "DN" Current Tint setting value – 1
Details	Set Tint value of user control The value set by this command will not be saved to projector. Therefore, when turning into Stanby status or ALL is OFF, the value returns to original setting. (The value is held in Suspend mode.) This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 19

8.4.5 CF_SHARP Command

Command	"CF_SHARP_%1"[CR]
%1	"000~015" Directly select Sharpness setting value "UP" Current Sharpness setting value + 1 "DN" Current Sharpness setting value - 1
Details	Set Sharpness The value set turning into Sta value is held in This command	value of user control by this command will not be saved to projector. Therefore, when inby status or ALL is OFF, the value returns to original setting. (The Suspend mode.) is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.4.6 CF_GAMMA Command

Command	"CF_GAMMA_%1"[CR]
%1	"000~015" Directly set Gamma setting value "UP" Current Gamma setting value + 1 "DN" Current Gamma setting value – 1
Details	Set Gamma value of user control The value set by this command will not be saved to projector. Therefore, when turning into Stanby status or ALL is OFF, the value returns to original setting. (The value is held in Suspend mode.) This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.4.7 CF_WBAL - Command

Command	"CF_WBAL-%1_%2"[CR]
%1	" R" Red " G" Green " B" Blue
%2	"000~063" Directly select Color value specified by White Balance%1 "UP" Current Color value set by White Balance%1 + 1 "DN" Current Color value set by White Balance%1 - 1
Details	Set Color value set by White Balance%1 of user control The value set by this command will not be saved to projector. Therefore, when turning into Stanby status or ALL is OFF, the value returns to original setting. (The value is held in Suspend mode.) This command is available in normal Power ON status.
Bosponso	Acceptable	"000"[CR]
iveshouse	Unacceptable	"Error Code"[CR]

Page 20

8.4.8 CF_COLTEMP Command

Command	"CF_COLTEMP_%1"[CR]
%1	"000" Xlow "001" Low "002" Mid "003" High
Details	Set Color Temperature. (Available only in the normal Power ON status) The value set by this command will not be saved to the projector. Therefore, when turning into Stanby status or ALL is OFF, the value returns to original setting. (The value is held in Suspend mode.) This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.4.9 CF PROGV Command

Command	"CF_PROGV_%1"[CR]
%1	"FILM" Select Progressive Mode FILM "L1" Select Progressive Mode L1 "L2" Select Progressive Mode L2 "OFF" Cancel Progressive scan "UP"Switch Progressive mode forward OFF → L1 → L2 → FILM → OFF "DN"Switch Progressive mode backward OFF → FILM → L2 → L1 → OFF
Details	Set / cancel Progressive scan The value set by this command will not be saved to projector. Therefore, when turning into Stanby status or ALL is OFF, the value returns to original setting. (The value is held in Suspend mode.) This command is available in normal Power ON status.
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.4.10 CF_NZRED Command

Command	"CF_NZRED_%1"[CR]
%1	"OFF" Cancel Noise Reduction "L1" Noise Reduction for moving image "L2" Noise Reduction for still image "UP"Switch Progressive mode forward OFF → L1 → L2 → FILM → OFF "DN"Switch Progressive mode backward OFF → FILM → L2 → L1 → OFF
Details	Noise Reduction based on frame correlation Select L1 or L2 depending on motion detection L2 is more effective in reducing noise than L1, however, L2 can have a blur in moving image The value set by this command will not be saved to projector. Therefore, when turning into Stanby status or ALL is OFF, the value returns to original setting. (The value is held in Suspend mode.) This command is available in normal Power ON status.
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 21

8.4.11 CF_IMAGE Command

Command	"CF_IMAGE_%	"CF_IMAGE_%1"[CR]
%1	"DYNAMIC" Dynamic (Fixed value to enable projection with a sharp, powerful picture tone) "STAND" Standard (Image adjust value is set to factory default) "REAL" Real (Fixed value to display graphic image with natural tone) "CINEMA" Cinema (Fixed value to focus on tone reproduction for movie) "BLACKBOARD" – Blackboard (Fixed value to project image onto green-colored blackboard) "COLORBOARD " – Colorboard(Fixed value to project image onto colored board) "CUSTOM1" Image1 (the value set and stored by a user) "CUSTOM3" Image3 (the value set and stored by a user) "CUSTOM4" Image4 (the value set and stored by a user)
Details	Select Image Mode Parameter "CUSTOM1" to "CUSTOM4" is the same as "Image1" to "Image4" displayed when selecting Image on OSD menu. The value set by this command is stored in EEPROM and its setting is effective even after ALL is OFF. This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
response	Unacceptable	"Error Code"[CR]

8.4.12 CF_IMAGEADJ Command

Command	"CF_IMAGEADJ_%1"[CR]
%1	"RST" Reset Image adjustment "STR1" Store current Image adjustment to Image 1 "STR2" Store current Image adjustment to Image 2 "STR3" Store current Image adjustment to Image 3 "STR4" Store current Image adjustment to Image 4 Reset / store Image adjustment. Parameter "STR1" to "STR4" is the same as "Image1" to "Image4" displayed when adjusting Image on OSD menu and selecting "Store" The value stored to "Image1-4" is saved and its setting is effective even after ALL is OFF. This command is available in normal Power ON status.
Details
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 22

8.5 PC Adjust Control Command

8.5.1 CF FSYNC Command

Command	"CF_FSYNC_%1"[CR]
%1	"0000~0031" Directly select Fine Sync setting value "UP" Current Fine Sync setting value + 1 "DN" Current Fine Sync setting value - 1
Details	Set Fine Sync value of PC signal The value set by this command will not be saved to projector. Therefore, when turning into Stanby status or ALL is OFF, the value returns to original setting. This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"101"[CR] when Input for Video is selected

8.5.2 CF TDOTS Command

Command	"CF_TDOTS_%1"[CR]
%1	"mmmm~nnnn" Directly select Total Dots setting value "mmmm" shows minimum value, it is current Display Dots value + Horizontal Position value. "nnnn" shows maximum value, which is not over 140MHz. "UP" Current Total Dots setting value + 1 "DN" Current Total Dots setting value - 1
Details	Set Total Dots of PC signal The value set by this command will not be saved to projector. Therefore, when turning into Stanby status or ALL is OFF, the value returns to original setting. This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"101" [CR] when Input for Video is selected

8.5.3 CF_CLAMP Command

Command	"CF_CLAMP_%1"[CR]
%1	"mmmm~nnnn" Directly select Clamp setting value "mmmm" shows minimum value, fixed-value "0001". "nnnn" shows maximum value: it depends on input signal. "UP" Current Clamp setting value + 1 "DN" Current Clamp setting value - 1
Details	Set Clamp value of PC signal The value set by this command will not be saved to projector. Therefore, when turning into Stanby status or ALL is OFF, the value returns to original setting. This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"101" [CR] when Input for Video is selected

Page 23

8.5.4 CF_H – POS Command

Command	"CF_H-POS_%1"[CR]
%1	"0000~nnnn" Directly select Horizontal Position setting value "nnnn" shows maximum value, it is current Total Dots value - Display Dots value "UP" Current Horizontal Position setting value + 1 "DN" Current Horizontal Position setting value - 1
Details	Set Horizontal Position value of PC signal. The value set by this command will not be saved to projector. Therefore, when turning into Stanby status or ALL is OFF, the value returns to original setting. This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"101"[CR] when Input for Video is selected

8.5.5 CF_V – POS Command

Command	"CF_V-POS_%1"[CR]
%1	"0000~nnnn" Directly select Vertical Position setting value "nnnn" shows maximum value, it is current Total Line value - Display Line value "UP" Current Vertical Position setting value + 1 "DN" Current Vertical Position setting value - 1
Details	Set Vertical Position value of PC signal The value set by this command will not be saved to projector. Therefore, when turning into Stanby status or ALL is OFF, the value returns to original setting. This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"101"[CR] When Input source is Video system

8.5.6 CF_DDOTS Command

Command	"CF_DDOTS_%1"[CR]
%1	"0256"~"nnnn" Directly select Display Dots setting value "nnnn" shows maximum value, it is current Total Dots value - Horizontal Position value Even number is available and when odd number is set, it is rounded out. "UP" Current Display Dots setting value + 2 "DN" Current Display Dots setting value - 2
Details	Set Display Dots value of PC signal The value set by this command will not be saved to projector. Therefore, when turning into Stanby status or ALL is OFF, the value returns to original setting. This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"101"[CR] When Input for Video is selected

Page 24

8.5.7 CF_DLINE Command

Command	"CF_DLINE_%1"[CR]
%1	"0100"~"nnnn" Directly select Display Line setting value "nnnn" shows maximum value, it is current Total Line value – Vertical Position value "UP" Current Display Line setting value + 1 "DN" Current Display Line setting value – 1
Details	Set Display Line value of PC signal The value set by this command will not be saved to projector. Therefore, when turning into Stanby status or ALL is OFF, the value returns to original setting. This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"101" [CR] When Input for Video is selected

8.5.8 CF_PCSTORE Command

Command	"CF_PCSTORE_%1"[CR]
%1	"MODE1" Store current PC Adjust status to Mode1 "MODE2" Store current PC Adjust status to Mode2 "MODE3" Store current PC Adjust status to Mode3 "MODE4" Store current PC Adjust status to Mode4 "MODE5" Store current PC Adjust status to Mode5
Details	Store current PC Adjust status (each parameter status such as Total dots) to Mode1~Mode5. This command operates the same way as storing to Mode1-Mode5 in PC Adjust MENU. This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"101" [CR] When Input for Video is selected

8.5.9 CF PCMODEFREE Command

Command	"CF_PCMODEFREE_%1"[CR]
%1	"MODE1" Set Mode1 to Free status "MODE2" Set Mode2 to Free status "MODE3" Set Mode3 to Free status "MODE4" Set Mode4 to Free status "MODE5" Set Mode5 to Free status
Details	Delete the registered data in Mode1-Mode5 and turns it to Free status. This command operates the same as turning Mode1-Mode5 to Free in PC Adjust Menu. This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"101"[CR] When Input for Video is selected

Page 25

8.6 Input Control Command

8.6.1 CF INPUT Command

Command	"CF_INPUT_%1"[CR]
%1	"CONPUTER1" Select Computer1 Input "COMPUTER2" Select Computer2 Input "VIDEO" Select Video Input "S-VIDEO" Select S-video "NETWORK" Select Network "UP" Switch Input setting forward Computer1 → Computer2 → Video →S-video→ Network → "DN"Switch Input setting backward Network → S-video → Video → Computer2 →Computer1→
Details	Select Input The same operation as "INPUT" button of the projector and Remote Control. This command is available in normal Power ON status.
Posponso	Acceptable	"000"[CR]
rresponse	Unacceptable	"Error Code"[CR]

8.6.2 CF_SOURCE Command

Command	"CF_SOURCE	_%1"[CR]
%1	Input is Computer 1	"ANALOG" Select Analog Input "YPBPR" Select Component Input "SCART" Select Scart Input "UP" Switch Input as follows Analog →YPBPR →Scart → "DN" Switch Input as follows Scart →YPBPR →Analog →
	Input is Computer 2	"DIGITAL" Select DVI Input "HDCP" Select DVI HDCP Input "ANALOG" Select Analog Input "UP" Switch Input as follows DIGITAL → HDCP → ANALOG → DIGITAL "DN" Switch Input as follows ANALOG → HDCP → DIGITAL →ANALOG →
	Input is Video	"VIDEO" Select Composite Video Input "UP" "DN" Although there is no option of source, projector accepts parameter "UP" "DN"
	Input is S-video	"S - VIDEO" Select S-Video Input "UP" "DN" Although there is no option of source, projector accepts parameter "UP" "DN"
	Input is Wireless	Network Select Network "UP" "DN" Although there is no option of source, projector accepts parameter "UP" "DN"
Details	Select Source of currently selected Input When Input specified by %1 is inappropriate for selected Input, the projector returns "101" and the command is not executed. This command is available in normal Power ON status.
Posponco	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 26

8.6.3 CF_INPUT1 Command

Command	"CF_INPUT1_%1_"[CR]
%1	"ANALOG"Select Analog RGB Input "YPBPR" Select Component "SCART" Select SCART
Details	Select Computer 1 input and source specified by %1 at the same time. This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.6.4 CF_INPUT2 Command

Command	"CF_INPUT2_%1_"[CR]
%1	"DIGITAL"Select DVI Input "HDCP"Select DVI HDCP Input "ANALOG" Select Analog RGB Input
Details	Select Computer 2 input and source specified by %1 at the same time. This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.6.5 CF_INPUT3 Command

Command	"CF_INPUT3_%1_"[CR]
%1	"VIDEO" Select Composite video Input
Details	Select Videoinput. This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.6.6 CF_INPUT4 Command

Command	"CF_INPUT4_%1_"[CR]
%1	"S-VIDEO" Select S-video Input
Details	Select S-Video input. This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.6.7 CF_INPUT5 Command

Command	"CF_INPUT5 _%1"[CR]
%1	"Network" Select Network
Details	Select Network. This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 27

8.6.8 CF_INPUT_%1_%2 Command

Command	"CF_INPUT_%1_%2"[CR]
%1	"COMPUTER1" Select Computer1 Input "COMPUTER2" Select Computer2 Input "VIDEO" Select Analog Input "S-VIDEO" Select S-video Input
%2	When %1 is COMPUTER1 "ANALOG"Select Analog RGB Input "YPBPR"Select Component "SCART"Select SCART When %1 is COMPUTER2 "DIGITAL"Select DVI Input "HDCP"Select DVI HDCP Input "ANALOG"Select DVI HDCP Input When %1 is VIDEO "VIDEO" Select Video Input When %1 is S-VIDEO "S-VIDEO" Select S-Video Input
Details	Select Input specified by %1 and also Source specified by %2 at once This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 28

8.6.9 CF_SYSTEM Command

Command	"CF_SYSTEM_%1"[CR]
		"VGA1" Select VGA1
%1	Input is Computer	: "XGA1" Select XGA1 : "WXGA3" Select WXGA3 "1080l" Select 1080l "1035l" Select 1035l "720P" Select 720P "575P" Select 720P "575P" Select 75P "480P" Select 575P "480P" Select 575l "480l" Select 480l "MODE1"~ "MODE5" Select Mode 1~Mode 5
	Input is PC-Digital/ AV-HDCP	"D-XGA1" Select D-XGA1 : "D-WXGA3" Select D-WXGA3 "D-1080I" Select D-1080I "D-1035I" Select D-1035I "D-720P" Select D-720P "D-575P" Select D-575P "D-480P" Select D-480P
	Input is Video	"AUTO"
Details	Select System When Input sp returns "101"[C This command Note1) "NTSC" only wf Note2) "1080!" when In Note3) D-XGA	of currently selected Input becified by %1 is inappropriate for selected Input, the projector R] and the command is not executed is available in normal Power ON status. / "NTSC4.43" / "PAL" / "SECAM" / "PAL-M" / "PAL-N" is available hen Input is VIDEO / S-VIDEO / "1035I" / "720P" / "575P" / "480P" / "575I" / "480I" is available only hput is Y / Pb/Cb / Pr/Cr 1//D-480P is available only when Input is applicable.
	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 29

8.7 Screen Control Command

8.7.1 CF SCREEN Command

Command	"CF_SCREEN_%1"[CR]
%1	Input is Computer	"NORMAL"
%1	Input is Video	"NORMAL" Select Normal mode "WIDE" Select Wide mode "CUSTOM" Select Custom size "UP"Switch selectable screen size forward * Normal → Wide → Custom → Normal "DN"Switch selectable screen size backward * Custom → Wide → Normal → Custom
Details	Select image size on screen. When Input specified by %1 is inappropriate for selected Input, the projector returns "101" [CR] and the command is not executed. "DZOOM UP" and "DZOOM DN" start effecting from the first command. This command is available in normal Power ON status. Note) When Input is computer and AV sorts signals (480i / 575ietc) are entered, the signal recognized as Video Input.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.7.2 CF DZCENT Command

Command	"CF_DZCENT_%1"[CR]
%1	"CENT" Ca	"CENT" Cancel Digital Zoom (CENT: "CENTER")
Details	Cancel Digital Zoom When image is expanded or shrunk, reset its value. This command is available in normal Power ON status and when Input is Computer.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"101"[CR] when Input for Video is selected

Page 30

8.7.3 CF_KEYSTONE Command

Command	"CF_KEYSTONE_%1"[CR]
%1	"UP" Correct Keystone distortion to reduce upper part of image "FUP" Correct Keystone distortion to reduce upper part by 2steps "DN" Correct Keystone distortion to reduce lower part of image "FDN" Correct Keystone distortion to reduce lower part by 2steps "LEFT" Correct Keystone distortion to reduce left part of image "FLFT " Correct Keystone distortion to reduce left part by 2steps "RIGHT" Correct Keystone distortion to reduce right part of image "FRGT" Correct Keystone distortion to reduce right part of image "RGT" Correct Keystone distortion to reduce right part by 2steps "RST" Return to its default value
Details	Change Keystone distortion correction This command is available in normal Power ON status.
	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR] "201"[CR]When reaching the Keystone correction limit or reaching 1 step to correction limit and "FDN"/"FUP" is received. (The command is not executed)

8.7.4 CF_KYSTNMODE Command

Command	"CF_KYSTNMODE_%1"[CR]
%1	"STR" Set Keystone store mode to Store "RST" Set Keystone store mode to Reset
Details	Set Keystone store mode This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.7.5 CF_CORNER-UL Command

Command	"CF_CORNER-UL_%1"[CR]
%1	"UP" Correct the horizontal line of image upwards "DN" Correct the horizontal line of image downwards "LEFT" Correct the vertical line of image to the left "RIGHT" Correct the vertical line of image to the right
Details	Correct the top-left corner of the image. (Available in normal Power ON status only) The correction starts with the first command received Projector returns error code ""101 and no operation is made when exceeding the correction limit
Deenenee	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 31

8.7.6 CF_CORNER-UR Command

Command	"CF_CORNER-UR_%1"[CR]
%1	"UP" Correct the horizontal line of image upwards "DN" Correct the horizontal line of image downwards "LEFT" Correct the vertical line of image to the left "RIGHT" Correct the vertical line of image to the right
Details	Correct the top-right corner of the image. (Available in normal Power ON status only) The correction starts with the first command received Projector returns error code "101 and no operation is made when exceeding the
	correction limit,
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.7.7 CF_CORNER-DL Command

Command	"CF_CORNER-DL%1"[CR]
%1	"UP" Correct the horizontal line of image upwards "DN" Correct the horizontal line of image downwards "LEFT" Correct the vertical line of image to the left "RIGHT" Correct the vertical line of image to the right
Details	Correct the bottom-left corner of the image. (Available in normal Power ON status only) The correction starts with the first command received Projector returns error code "101 and no operation is made when exceeding the correction limit,
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.7.8 CF_CORNER-DR Command

Command	"CF_CORNER-DR_%1"[CR]
%1	"UP" Correct the horizontal line of image upwards "DN" Correct the horizontal line of image downwards "LEFT" Correct the vertical line of image to the left "RIGHT" Correct the vertical line of image to the right
Details	Correct the bo status only) The correction Projector return	ottom-right corner of the image. (Available in normal Power ON starts with the first command received
	correction limit,
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 32

8.7.9 CF_CORNERTESTPAT Command

	Command	"CF_CORNERTESTPAT_%1"[CR]
	%1	"RED"Select Red "WHITE" Select White "BLUE" Select Blue "OFF" Select Off
	Details	Display test patterns for Correctcorrection. (Available in normal Power ON status only) The value set by this command is stored in EEPROM and its setting is effective even after ALL is OFF.
Acce		Acceptable	"000"[CR]
	Response	Unacceptable	"Error Code"[CR]

8.7.10 CF_VSCALE Command

Command	"CF_VSCALE_%1"[CR]
%1	"032" +32 "031" +31 : "002" +2 "001" +1 "000" +0 "-01"1 "-02"2 : "-31"31 "-32"32 "UP" Vertical Scale setting value + 1 "DN" Vertical Scale setting value - 1
Details	Set Vertical Scale This command is available in normal Power ON status. Note1) When Screen setting is not in Custom mode, projector changes image mode into Custom by receiving this command. Note2) When there is no signal detected, projector returns 101 and the command does not excute.
Posponso	Acceptable	"000"[CR]
response	Unacceptable	"Error Code"[CR]

Page 33

8.7.11 CF_VPOS Command

Command	"CF_VPOS_%1"[CR]
%1	"015" +15 "014" +14 : "002" +2 "001" +1 "000" +0 "-01"1 "-02"1 "-02"2 : "-14"15 "UP" Vertical Position setting value + 1 "DN" Vertical Position setting value - 1
Details	Set Vertical Position This command is available in normal Power ON status. Note1) When Screen setting is not in Custom mode, projector changes image mode into Custom by receiving this command. Note2) When there is no signal detected, projector returns 101 and the command does not excute
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.7.12 CF_HSCALE Command

Command	"CF_HSCALE_%1"[CR]
%1	"032" +32 "031" +31 : "002" +2 "001" +1 "000" +1 "000" +0 "-01"1 "-02"2 : "-31"31 "-32"32 "UP" Horizontal Scale setting value + 1 "DN" Horizontal Scale setting value - 1
Details	Set Horizontal Scale This command is available in normal Power ON status. Note1) When Screen setting is not in Custom mode, projector changes image mode into Custom by receiving this command. Note2) When there is no signal detected, projector returns 101 and the command does not excute.
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 34

8.7.13 CF_HPOS Command

Command	"CF_HPOS_%1"[CR]
%1	"015" +15 "014" +14 : "002" +2 "001" +1 "000" +0 "-01"1 "-02"2 : "-14"14 "-15"15 "UP" Horizontal Position setting value + 1 "DN" Horizontal Position setting value - 1
Details	Set Horizontal Position This command is available in normal Power ON status. Note1) When Screen setting is not in Custom mode, projector changes image mode into Custom by receiving this command. Note2) When there is no signal detected, projector returns 101 and the command does not excute.
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 35

8.8 Lamp Command

8.8.1 CF LAMPH Command

Command	"CF_LAMPH_%1"[CR]
%1	"RST"
Details	Reset Lamp use time counter. (Available in normal Power ON status only).
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.8.2 CF_LAMPMODE Command

Command	"CF_LAMPMODE_%1"[CR]
%1	"HIGH" Set lamp to High mode "NORMAL" Set lamp to Normal mode "ECO" Set lamp to 3L mode "UP" Switch Lamp mode forward. (High - Normal - Eco – High) "DN" Switch Lamp mode backward. (Eco - Normal -High –Eco)
Details	Select Lamp Mode The value set by this command is stored in EEPROM and its setting is effective even after ALL is OFF. This command is available in normal Power ON status.
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 36

8.9 Sound Command

8.9.1 CF VOLUME Command

Command	"CF_VOLUME_%1"[CR]
%1	"000-063" "UP" "DN"	Directly select Volume setting value Current Volume setting value +1 Current Volume setting value -1
Details	Control Volume value The same operation of Volume Up/Down as projector and RC, and directly select Volume setting value. When setting Volume value, the Sound Mute ON status is canceled just like RC operation. The value set by this command is stored in Projector. This command is available in normal Power ON status.
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.9.2 CF_MUTE Command

Command	"CF_MUTE_%1"[CR]
%1	"ON" Set Sound Mute to ON "OFF" Set Sound Mute to OFF
Details	Control Sound Mute ON/OFF This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 37

8.10 Setting Command

8.10.1 CF_LANG Command

Command	"CF_LANG_%1"[CR]
%1	"ENG" "DEU" "FRA" "ESP" "NED" "SVE" "SVE" "KOR" "KOR" "FIN" "POL" "HUN" "ROM" "THA"	Select English Select German Select French Select Italian Select Spanish Select Portuguese Select Dutch Select Swedish Select Russian Select Russian Select Chinese Select Chinese Select Korean Select Korean Select Korean Select Finnish Select Finnish Select Polish Select Hungarian Select Romanian Select Thai
Details	Set language for OSD The language set by this command is stored in EEPROM and its setting is effective after ALL is OFF. This command is available in normal Power ON status.
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.10.2 CF_MENUPOSITION Command

Command	"CF_MENUPOSITION_%1"[CR]
%1	"SET" Move the menu display to next position
Details	Change the menu position This command is available in normal Power ON status. The language set by this command is stored in EEPROM and its setting is effective after ALL is OFF. Position: top left - top right – center – bottom left-bottom right top left
Boononoo	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.10.3 CF AUTOSETUPPCADJ Command

Command	"CF_AUTOSETUPPCADJ_%1"[CR]
%1	"ON" Set Auto PC ADJ. function to ON "OFF" Set Auto PC ADJ. function to OFF
Details	Set/Cancel Auto PC adj. function This command is available in normal Power ON status. Note) It is unable to set Keystone, PC ADJ. and Input search to OFF at once. e.g. If projector receives Auto PC ADJ. OFF command while Keystone and Input search are OFF, it returns error code "101".
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 38

8.10.4 CF_AUTOSETUPKEYSTONE Command

Command	"CF_AUTOSETUPKEYSTONE_%1"[CR]
%1	"AUTO" "MANUAL" "OFF"	Set Auto Keystone function to Auto Set Auto Keystone function to Manual Set Auto Keystone function to OFF
Details	Set Keystone function of Auto setup This command is available in normal Power ON status. Note) It is unable to set Keystone, PC ADJ. and Input search to OFF at once. e.g. If projector receives Keystone OFF command while Auto PC ADJ. and Input search are OFF, it returns error code "101"
Posponso	Acceptable	"000"[CR]
rresponse	Unacceptable	"Error Code"[CR]

8.10.5 CF_INPUTSEARCH Command

Command	"CF_INPUTSEARCH_%1"[CR]
%1	"OFF" Set Input search operation to OFF "ON1" Set Input search operation to On1 "ON2" Set Input search operation to On2
Details	Set Input search operation mode. The status set by this command is stored in EEPROM and its setting is effective after ALL is OFF This command is available in normal Power ON status. Note) It is unable to set Keystone, PC ADJ. and Input search to OFF at once. e.g. If projector receives Input search OFF command while Auto PC ADJ. and Keystone are OFF, it returns error code "101"
Posponso	Acceptable	"000"[CR]
Tresponse	Unacceptable	"Error Code"[CR]

8.10.6 CF AUTOSETUP

Command	"CF_AUTOSETUP_%1"[CR]
%1	"START" Execute Auto Setup
Details	Excute Auto Setup Note) CF commands does not execute while Auto setup is in process. If the command is sent during this, projector returns error code "302"
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.10.7 CF_BACKGND Command

Command	"CF_BACKGND_%1" [CR]
%1	"BLUE" Select Blue Back "USER" Select User "BLACK" Select Black Back "UP" Switch forward (Blue Back→User→Black Back→Blue Back) "DN" Switch backward (Blue Back→Black Back→User→Blue Back)
Details	Set Screen status for no signal.(Available only in the normal Power ON status) The status set by this command is stored in EEPROM and the setting remains even after the power is turned to ALL OFF status. *When %1="USER" is received, error code "101" is returned, in the case of Capture non-practice.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

Page 39

8.10.8 CF_DISP Command

Command	"CF_DISP_%1"[CR]
%1	"ON" Select Display "OFF" Cancel Display "CNTDWNOFF" Count down OFF "UP" Switch Display mode forward (On → Count down OFF → Off → On → · · ) "DN" Switch Display mode backward (On → Off → Count down OFF → On → · · )
Details	Set / Cancel Display The value set by this command is stored in EEPROM and its setting is effective even after ALL is OFF. This command is available in normal Power ON status.
Bosponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.10.9 CF_LOGO Command

Command	"CF_LOGO_%1_%2"[CR]
%1	"0000"-"9999" Set LOGO PIN CODE directly
%2	"OFF" Disable Logo function "DFLT" Display Default Logo "USER" Display Captured Logo "UP" Switch Logo setting forward (OFF → DFLT → User → OFF → · ·) "DN" Switch Logo setting backward (OFF → User → DFLT → OFF → · ·)
Details	Set / Cancel Logo The value set by this command is stored in EEPROM and its setting is effective even after ALL is OFF This command is available in normal Power ON status. %1 Set LOGO PIN CODE - When LOGO LOCK is in operation PIN CODE is correct Command is valid (Acceptable) PIN CODE is incorrect Command is invalid (Error Code "102") PIN CODE is out of %1 range Command is invalid (Error Code "? ") -When LOGO LOCK is not in operation PIN CODE is within %1 range Command is invalid (Error Code "? ") -When LOGO LOCK is not in operation PIN CODE is out of %1 range Command is invalid (Error Code "? ") -When LOGO LOCK is not in operation PIN CODE is out of %1 range Command is invalid (Error Code "? ") Note) Receiving correct LOGO PIN CODE while LOGO LOCK is in operation enables to change LOGO setting, but it does not release LOGO LOCK. (LOGO LOCK continues.) Projector returns Error Code "101" by receiving USER in %2 when capture has not operated
Boononoo	Acceptable	"000"[CR]
rresponse	Unacceptable	"Error Code"[CR]

Page 40

8.10.10 CF_USBTERMINAL Command

Command	"CF_USBTERMINAL_%1"[CR]
%1	"DISPLAY"Select Display "MOUSE" Select Mouse control
Details	Switch usage of USB terminal. The value set by this command is stored in EEPROM and its setting is effective even after ALL is OFF This command is available in normal Power ON status.
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.10.11 CF CEIL Command

Command	"CF_CEIL_%1"[CR]
%1	"ON" Set Ceiling to ON "OFF" Set Ceiling to OFF
Details	Set/Cancel Ceiling setting. The value set by this command is stored in EEPROM and its setting is effective even after ALL is OFF This command is available in normal Power ON status.
Bosponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.10.12 CF REAR Command

Command	"CF_REAR_%1"[CR]
%1	"ON" Set Rear to ON "OFF" Set Rear to OFF
Details	Set/Cancel Rear setting. When Rear is ON, image is left/right reversed. The status set by this command is stored in EEPROM and its setting is effective after ALL is OFF This command is available in normal Power ON status.
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.10.13 CF_POINTER Command

Command	"CF_POINTER_%1"[CR]
%1	"SPOTLIGHTMAX" Select Maximum Spotlight "SPOTLIGHTMID" Select Medium Spotlight "SPOTLIGHTMIN" Select Minimum Spotlight "ARROW" Select Arrow "FINGER" Select Finger mark "LASER" Select Laser mark
Details	Select Pointer style This command is available in normal Power ON status.
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 41

8.10.14 CF_P-MANE Command

Command	"CF_P - MANE_%1"[CR]
%1	"OFF" Set Power Management to OFF "READY" Set Power Management to Ready "SHUTDOWN" Set Power Management to Shut Down mode "UP" Switch Power management setting (Off → Ready → Shutdown → Off) "DN" Switch Power management setting (Off → Shutdown → Ready → Off)
Details	Set/Cancel Power Management The status set by this command is stored in EEPROM and its setting is effective after ALL is OFF This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.10.15 CF P-MANETIME Command

Command	"CF_P-MANETIME_%1"[CR]
% 1	"01" ~ "30" "UP" "DN"	Directly select setting time by the minute Plus one minute (01 → 02 → ···· → 30 → 01) Minus one minute(30 → 29 → ··· → 01 → 30)
Details	Set Power Management time The status set by this command is stored in EEPROM and its setting is effective after ALL is OFF This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.10.16 CF ON-STA Command

Command	"CF_ON - STA_%1"[CR]
%1	"ON" Set Power On Start to ON "OFF" Set Power On Start to OFF "UP" Switch setting (On → Off → On → ···) "DN" Switch setting (On → Off → On → ···) Note) "UP" and "DN" behave the same.
Details	Set/Cancel Power ON Start The status set by this command is stored in EEPROM and its setting is effective after ALL is OFF This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.10.17 CF STANDBYMODE Command

Command	"CF_STANDBYMODE_%1"[CR]
%1	"ECO" Less standby electricity "NORMAL" Normal standby electricity (Selecting NETWORK)
Details	Switch Standby Mode setting. This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 42

8.10.18 CF_CCAPTIONDISP Command

Command	"CF_CCAPTIONDISP_%1"[CR]
%1	"OFF" Select Off "CC1" Select CC1 "CC2" Select CC2 "CC3" Select CC3 "CC4" Select CC4
Details	Select channel of Closed caption. The status set with this command is stored in EEPROM and its setting is effective even after ALL is OFF. This command is available in normal Power ON status. Closed caption is available under conditions below; Entered signal is appropriate (Video, NTSC signal of S-video, Component=480i) and System is fixed to NTSC or 480i.
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.10.19CF CCAPTIONCOLOR Command

Command	"CF_CCAPTIONCOLOR_%1"[CR]
%1	"COLOR" Select Color "WHITE" Select White
Details	Select color of Closed caption. The status set with this command is stored in EEPROM and its setting is effective even after ALL is OFF. This command is available in normal Power ON status. Closed caption is available under conditions below; Entered signal is appropriate (Video, NTSC signal of S-video, Component=480i) and System is fixed to NTSC or 480i.
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.10.20 CF RCODE Command

Command	"CF_RCODE_"	"CF_RCODE_%1"[CR]
%1	"001" Select Code1 "002" Select Code2 "003" Select Code3 "004" Select Code4 "005" Select Code5 "006" Select Code6 "007" Select Code7 "008" Select Code8 "UP" Switch Code setting of Remote Control forward (Code1 → Code2 → Code3 → Code8 → Code1) "DN" Switch Code setting of Remote Control backward (Code8 → Code7 → Code6 → Code1 → Code8)
Details	Select Code of Remote Control The status set by this command is stored in EEPROM and its setting is effective after ALL is OFF This command is available in normal Power ON status.
Bosponso	Acceptable	"000"[CR]
response	Unacceptable	"Error Code"[CR]

Page 43

8.10.21 CF_KEYDIS Command

Command	"CF_KEYDIS_%1"[CR]
%1	"NONE" RC & Projector keys are valid (All are valid) "RC" RC keys are invalid "KEY" Projector keys are invalid
Details	Diable RC/Projector keys This command is available in normal Power ON status.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.10.22 CF_PJPINCODE Command

Command	"CF_PJPINCODE_%1"[CR]
%1	"0000" – "9999	"Set PJ PIN CODE directly
Details	Set PJ PIN CO PIN CODE can -When PJ LOC PIN CODE is PIN CODE is PIN CODE is ON CODE is of PIN CODE is of PIN CODE is of This command and Count dow Also when PJ everytime lamo	DE to release PJ LOCK. not be changed by this command. K is in operation s correct Command is valid (Acceptable) s incorrect Command is invalid(Error Code"102") s out of %1 range Command is invalid (Error Code "? ") K is not in operation i thin %1 range Command is valid (Acceptable) ut of %1 range Command is invalid (Error Code "? ") is valid during a dialog "PJ PIN CODE" is displayed after Power On n. LOCK setting is "On1", it is necessary to transmit this command burns on
	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.10.23 CF_FANMODE Command

Command	"CF_FANMODE_%1"[CR]
%1	"L1" Set Fan Mode to L1 "L2" Set Fan Mode to L2
Details	Switch Fan Mo When L1 is sel When L2 is se rotates longer t The status set even after ALL This command	de ected, fan noise after POWER OFF is louder. lected, fan noise after POWER OFF becomes quiet, however, fan han L1. by this command is stored in EEPROM and its setting is effective is OFF. is available in normal Power ON status.
Bosponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 44

8.10.24 CF_FANCONTROL Command

Command	"CF_FANCONTROL_%1"[CR]
%1	"OFF"
Details	Set Fan contro The status set even after ALL This command	I setting. by this command is stored in EEPROM and its setting is effective is OFF. is available in normal Power ON status.
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.10.25 CF_FILTIMER Command

Command	"CF_FILTIMER_%1"[CR]
%1	"100" Set 100 hours "200" Set 200 hours "300" Set 300 hours "OFF" No warning display "UP" Switch Filter timer forward (Off → 100 → 200 → 300 → Off) "DN" Switch Filter timer backward
Details	Set timer of Filter replacement /clean-up warning display.
Response	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.10.26 CF FILH Command

Command	"CF_FILH_%1"[CR]
%1	"RST"Reset Filter used time
Details	Reset filter used time
Dooponoo	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.10.27 CF_FDEFAULT Command

Command	"CF_FDEFAULT_%1"[CR]
%1	"RST"
Details	Set the value to Factory Default This command is available in normal Power ON status.
Boononoo	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 45

8.11 Other Command

8.11.1 CF KEYENU Command

Command	"CF_KEYENU_%1"[CR]
%1	"RIGHT" Shift Pointer on OSD Menu to right "LEFT" Shift Pointer on OSD Menu to left "UP" Shift Pointer on OSD Menu to right "DN" Shift Pointer on OSD Menu to right "SELECT" Behave the same as Select key of Remote control "AUTOPC" Execute Auto PC adj
Details	This command behave the same as corresponding keys of Remote Control / Projector Auto PC adj. keeps operating even though projector receives this command again while Auto PC adj. is in process.
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.11.2 CF_MENU Command

Command	"CF_MENU_%1"[CR]
%1	"ON" Display OSD Menu "OFF" Cancel OSD menu
Details	Display / Cancel On Screen Display Menu This command is available in normal Power ON status.
Posponso	Acceptable "000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.11.3 CF_POWER Command

Command	"CF_POWER_%1"[CR]
	"ON" "OFF"	Power ON projector Power OFF Projector
	Note1) Count o	lown can be terminated by sending this command.
%1	Note2) Projector returns error code due to unable of command execution depends on its condition.
	Note3) Although projector ruturns "OK", operation may not be proceeding properly. (e.g. After returning "000" for Power ON command, projector gets abnormal temperature.) Use Status read command to get projector states.
Details	Power ON / OFF projector.
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 46

8.11.4 CF_FREEZE Command

Command	"CF_FREEZE_%1"[CR]
%1	"ON" Set Freeze to ON "OFF" Set Freeze to OFF "UP" Switch setting (On → Off → On → ···) "DN" Switch setting (On → Off → On → ···) Note) "UP" and "DN" behave the same.
Details	Set/Cancel Freeze setting. Although projector returns "000", receiving another Freeze command does not release Freeze operation. This command is available in normal Power ON status.
Posponso	Acceptable "000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.11.5 CF VMUTE Command

Command	"CF_VMUTE_%1"[CR]
%1	"ON" Set No show ON "OFF" Set No show OFF "UP" Switch setting (On → Off → On → ···) "DN" Switch setting (On → Off → On → ···) Note) "UP" and "DN" behave the same.
Details	Set/Cancel No show setting. This command is available in normal Power ON status.
Bosponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

8.11.6 CF PTIMER Command

Command	"CF_PTIMER_	%1"[CR]
%1	"SET"Excute P-TIMER
Details	Display / Suspend / Cancel P-TIMER This command behaves the same as "P-TIMER" key of Remote Control / Projector.
Posponso	Acceptable	"000"[CR]
Response	Unacceptable	"Error Code"[CR]

Page 47

9. Status Read Command

9.1 Format

1) PC issues commands in format as below:

"CR_Command" [CR]

Command : Character Line

2) When projector receives the appropriate command, it returns a character line as the

required data

"000__"%1 [CR]

%1: Required Data (Character Line. See [Basic Status Read Command Table])

3) When the received data cannot be decoded, the projector returns "?"[CR]

9.2 Transfer Example

Get total dots of projector by Expand Commands

PC → PJ: "CR_TDOTS" [CR]

PC ← PJ: "000_1344" [CR]

9.3 Operation Condition

1) Basically Status Read Commands should be always operated.
2) Status Read Commands are invalid when projector is in standby under Eco mode

Page 48

9.4 Image Status Read Command

9.4.1 CR BRIGHT Command

Command	"CR_BRIGHT"[CR]
Details	Get Brightness value of user control
Response	Acceptable	"000_% a"[CR]
	%a	"000"~"063"
	Unacceptable	"Error Code"[CR]

9.4.2 CR_CONT Command

Command	"CR_CONT"[CR]
Details	Get Contrast value of user control
	Acceptable	"000_% a"[CR]
Response	%a	"000"~"063"
Response	Unacceptable	"Error Code"[CR]

9.4.3 CR COLOR Command

Command	"CR_COLOR"[CR]
Details	Get Color value of user control
	Acceptable	"000_%a"[CR]
Response	%a	"000"~"063"
Response	Unacceptable	"Error Code"[CR]

9.4.4 CR_TINT Command

Command	"CR_TINT"[CR]
Details	Get Tint value of user control
Response	Acceptable	"000_%a"[CR]
	%a	"000"~"063"
	Unacceptable	"Error Code"[CR] When the command is invalid due to condition such as Input source "?"[CR] When unclear command is received

9.4.5 CR_SHARP Command

Command	"CR_SHARP"[CR]
Details	Get Sharpness value of user control
Response	Acceptable	"000_%a"[CR]
	%a	"000"~"015"
	Unacceptable	"Error Code"[CR]

Page 49

9.4.6 CR GAMMA Command

Command	"CR_GAMMA"[CR]
Details	Get Gamma value of user control
Response	Acceptable	"000_%a"[CR]
	%a	"000"~"015"
	Unacceptable	"Error Code"[CR]

9.4.7 CR_WBAL – R Command

Command	"CR_WBAL-R"[CR]
Details	Get White Balance Red value of user control
Response	Acceptable	"000_%a"[CR]
	%a	"000"~"063"
	Unacceptable	"Error Code"[CR]

9.4.8 CR_WBAL – G Command

Command	"CR_WBAL-G"[CR]
Details	Get White Balance Green value of user control
	Acceptable	"000_%a"[CR]
Response	%a	"000"~"063"
	Unacceptable	"Error Code"[CR]

9.4.9 CR WBAL – B Command

Command	"CR_WBAL-B"[CR]
Details	Get White Balance Blue value of user control
	Acceptable	"000_%a"[CR]
Response	%a	"000"~"063"
Response	Unacceptable	"Error Code"[CR]

9.4.10 CR COLTEMP Command

Command	"CR_COLTEMP"[CR]
Details	Get Color Temp. setting value
	Acceptable	"000_%a"[CR]
Response	%a	"000" Xlow "001" Low "002" Mid "003" High "BLACK" Blackboard(Green) mode selected "COLOR" Colorboard selected "BLANK" White Balance has been changed
	Unacceptable	"Error Code"[CR]

Page 50

9.4.11 CR_NZRED Command

Command	"CR_NZRED"[CR]
Details	Get setting status of Noise Reduction
	Acceptable	"000_%1"[CR]
Response	%1	"L1" Noise Reduction for moving image "L2" Noise Reduction for still image "OFF" Noise Reduction is OFF
Response	Unacceptable	"Error Code"[CR]

9.4.12 CR_PROGV Command

Command	"CR_PROGV"[CR]
Details	Get setting status of Progressive scan
	Acceptable	"000_%a"[CR]
Response	%a	"L1" Progressive Mode L1 is selected "L2" Progressive Mode L2 is selected "FILM" Progressive Model FILM is selected "OFF" Progressive scan is disabled
	Unacceptable	"Error Code"[CR]

9.4.13 CR IMAGE Command

Command	"CR_IMAGE"[CR]
Details	Get image setting status Required data "CUSTOM1" to "CUSTOM4" is the same as "Image1" to "Image4" displayed when selecting IMAGE on OSD menu
	Acceptable	"000_%a"[CR]
Response	%a	"DYNAMIC" Dynamic "STAND" Standard "REAL" Real "CINEMA" Cinema "BLACKBOARD" Blackboard "COLORBOARD" Colorboard "CUSTOM1"~"CUSTOM4" Image1~4
Response	Unacceptable	"Error Code"[CR] When the command is invalid due to condition such as Input source "?"[CR] When unclear command is received

9.4.14 CR IMGGMD Command

Command	"CR_IMGGMD"[CR]
Details	Get Image Gar	Get Image Gamma setting status
	Acceptable	"000_%a"[CR]
Response	%a	"DYN" Dynamic "STD" Standard "REL" Real "CNM" Cinema "BKB" Blackboard "CLB" Colorboard
	Unacceptable	"Error Code"[CR]

Page 51

9.5 PC Adjust Status Read Command

9.5.1 CR FSYNC Command

Command	"CR_FSYNC"[CR]
Details	Get Fine Sync value
	Acceptable	"000_%a"[CR]
_	%a	"0000"~"0031"
Response	Unacceptable	"Error Code"[CR] When the command is invalid due to condition such as Input source "?"[CR] When unclear command is received

9.5.2 CR_TDOTS Command

Command	"CR_TDOTS"[CR]
Details	Get Total Dots value
	Acceptable	"000_%a"[CR]
Response	%a	"nnnn"~"mmmm" (nnnn = Display Dots + Horizontal Position) (mmmm= Maximum value depends on input signal)
Response	Unacceptable	"Error Code"[CR] When the command is invalid due to condition such as Input source "?"[CR] When unclear command is received

9.5.3 CR CLAMP Command

Command	"CR_CLAMP"[CR]
Details	Get Clamp value
Response	Acceptable	"000_%a"[CR]
	%a	"0001"~"nnnn" ("nnnn" depends on input signal)
	Unacceptable	"Error Code"[CR] When the command is invalid due to condition such as Input source "?"[CR] When unclear command is received

9.5.4 CR H – POS Command

Command	"CR_H - POS"[CR]
Details	Get Horizontal Position value
Response	Acceptable	"000_%a"[CR]
	%a	"0000"~"nnnn" (nnnn = Total Dots - Display Dots)
	Unacceptable	"Error Code"[CR] When the command is invalid due to condition such as Input source "?"[CR] When unclear command is received

Page 52

9.5.5 CR_V – POS Command

Command	"CR_V - POS"[CR]
Details	Get Vertical Position value
Response	Acceptable	"000_%a"[CR]
	%a	"0000"~"nnnn" (nnnn = Total Line - Display Line)
	Unacceptable	"Error Code"[CR] When the command is invalid due to condition such as Input source "?"[CR] When unclear command is received

9.5.6 CR_DDOTS Command

Command	"CR_DDOTS"[CR]
Details	Get Display Dots value
	Acceptable	"000_%a"[CR]
Response	%a	"0256"~"nnnn" (nnnn = Total Dots – Horizontal Position value)
Response	Unacceptable	"Error Code"[CR] When the command is invalid due to condition such as Input source "?"[CR] When unclear command is received

9.5.7 CR DLINE Command

Command	"CR_DLINE"[CR]
Details	Get Display Lin	Get Display Line value
	Acceptable	"000_%a"[CR]
Response	%a	"0100"~"nnnn" (nnnn = Total Line – Vertical Position value)
	Unacceptable	"Error Code"[CR] When the command is invalid due to condition such as Input source "?"[CR] When unclear command is received

9.5.8 CR PCSTORE Command

Command	"CR_PCSTORE"[CR]
Details	Get Free/Stored status of MODE1 - MODE5 for PC Adjust Each data consists of 5 bytes. Each byte indicates the status of MODE1~MODE5 respectively. (F:Free S:Stored)
Response	Acceptable	"000_%a"[CR]
	%a	"FFFFF" All Free "SFFFF" MODE1 is Stored, others are Free : "FFFFS" MODE5 is Stored, others are Free "SSSSS" All Stored
	Unacceptable	"Error Code"[CR]

Page 53

9.6 Video Status Read Command

9.6.1 CR SERSYS Command

Command	"CR_SERSYS"	"CR_SERSYS"[CR]
Details	Get currently selected signal Returns auto-detected signal in Auto mode Only available for Video input. (N/A when Input is computer)
	Acceptable	"000_%a"[CR]
Response	%a	"1080I60" 1080i 60Hz "1080I50" 1080i 50Hz "1035I" 1035i "720P" 720p "575P" 575p "480P" 480p "575I" 575i (includes Composite signal such as PAL) "480I" 480i (includes Composite signal such as NTSC) "NO_SIGNAL" There is no signal
	Unacceptable	"101"[CR] When Input for PC is selected "?"[CR]

Page 54

9.7 Input Status Read Command

9.7.1 CR INPUT Command

Command	"CR_INPUT"[CR]
Details	Get selected INPUT No.
Response	Acceptable	"000_%1"[CR]
	Request data	"1"-"5"
	Unacceptable	"Error Code"[CR]

9.7.2 CR_SOURCE Command

Command	"CR_SOURCE"[CR]
Details	Get selected S	Get selected Source
	Acceptable	"000_%1"[CR]
Response	Request data	"DIGITAL" DVI Input is selected "ANALOG" Analog (RGB) Input is selected "SCART" SCART is selected "HDCP" HDCP is selected "VIDEO" Video Input is selected "S-VIDEO" S-Video Input is selected "YPBPR" Component Input is selected "NETWORK" Network is selected
	Unacceptable	"Error Code"[CR]

9.7.3 CR SRCINP1 Command

Command	"CR_SRCINP1" [CR]
Details	Get selected se	Get selected source of Input 1
	Acceptable	"000_%1"[CR]
Response	Request data	"ANALOG" Analog RGB Input is selected "YPBPR" YPBPR Input is selected "SCART" Scart Input is selected
	Unacceptable	"Error Code"[CR]

9.7.4 CR SRCINP2 Command

Command	"CR_SRCINP2" [CR]
Details	Get selected source of Input 2_CMP2
	Acceptable	"000_%1"[CR]
Response	Request data	"DIGITAL" DVI Input is selected "HDCP" HDCP Input is selected "ANALOG" Analog Input is selected
	Unacceptable	"Error Code"[CR]

9.7.5 CR SRCINP3 Command

Command	"CR_SRCINP3" [CR]
Details	Get selected se	Get selected source of Input 3_Video
Response	Acceptable	"000_%1"[CR]
	Request data	"VIDEO" Composite Video Input is selected
	Unacceptable	"Error Code"[CR]

Page 55

9.7.6 CR_SRCINP4 Command

Command	"CR_SRCINP4" [CR]
Details	Get selected source of Input 4_S-video
	Acceptable	"000_%1"[CR]
Response	Request data	"S - VIDEO" S-Video Input is selected
	Unacceptable	"Error Code"[CR]

9.7.7 CR_SRCINP5 Command

Command	"CR_SRCINP5" [CR]
Details	Get selected source of Input 5_Network
	Acceptable	"000_%1"[CR]
Response	Request data	"NETWORK" Network is selected
	Unacceptable	"Error Code"[CR]

Page 56

9.7.8 CR_SYSTEM Command

Command	"CR_SYSTEM"[CR]
Details	Get sel	ected System
	Acceptable		"000_%1"[CR]
	%1	Input is PC Analog	"VGA1" VGA1 is selected "VGA2" VGA2 is selected : "XGA1"
Response		Input is PC-Digital/ AV-HDCP	"D - XGA1" D-XGA1 is selected "D - WXGA3" D-WXGA3 is selected "D - 1080l" D-1080i is selected "D - 1035l" D-1035i is selected "D - 720P" D-720p is selected "D - 575P" D-575p is selected "D - 480P" D-480p is selected When there is no signal, projector returns error code"101"
		Input is Y,Pb/Cb,Pr /Cr	"AUTO" Auto is selected "1080i"1080i is selected "1035i"
		Input is Video,S-Vi deo	"AUTO" Auto is selected "NTSC" NTSC is selected "NTSC443" NTSC4.43 is selected "PAL" PAL is selected "SECAM" SECAM is selected "PAL - M" PAL-M is selected "PAL - N" AL-N is selected Projector returns selected System status regardless of the signal input.
		Input is Network	"NETWORK" Network is selected Projector returns selected System status regardless of the signal input.
	Una	cceptable	""Error Code"[CR]

Page 57

9.7.9 CR_SYSLIST Command

Command	"CR_SYSLIST"[CR]
Details	Get selectable	System titles
	Acceptable	"000_%1_%2%x" [CR]
Response	%1	- When Input is PC-Analog "XGA1"
	Unacceptable	""Error Code"[CR]

9.7.10 CR_MODELIST Command

Command	"CR_MODELIST"[CR]
Details	Get selectable Mode titles
	Acceptable	"000_%1_%2%x" [CR]
Response	%1 %2 : %x	Returns Error code "101" when Input is other than PC-Analog Returns Error code "101" when Input is PC-Analog but no signal When Input is PC-Analog and signal is found, returns selectable Mode among Mode1 – 5 "MODE1" : : "MODE5
	Unacceptable	"Error Code"[CR]

Page 58

9.8 Screen Status Read Command

9.8.1 CR SCREEN Command

Command	"CR_S	"CR_SCREEN"[CR]
Details	Get se	Get selected on-screen image size
	Acce	ptable	"000_%a"[CR]
Response	%a	Input is PC	"NORMAL" Normal mode is selected "TRUE" True mode is selected "WIDE" Wide mode is selected "FULL" Full mode is selected "CUSTOM" Custom mode is selected When the screen is set to D.Zoom, projector returns the previous status (NORMAL )
	%a	Input is Video	"NORMAL" Normal mode is selected "WIDE" Wide is selected "CUSTOM" Custom size is selected
	Unacceptable		"Error Code"[CR] When the command is invalid due to condition such as Input source "?"[CR] When unclear command is received

9.8.2 CR KYSTNMODE Command

Command	"CR_KYSTNMODE"[CR]
Details	Get setting status of Keystone Store Mode
	Acceptable "000_%a"[CR]
Response	%a	"STR" Store mode is "Store" "RST" Store mode is "Reset"
	Unacceptable	"Error Code"[CR]

9.8.3 CR_CORNERTESTPAT Command

Command	"CR_CORNERTESTPAT" [CR]
Details	Get setting status of Testpattern for Corner correction
	Acceptable	"000_%1"[CR]
Response	%a	"RED" Red is selected "WHITE" White is selected "BLUE" Blue is selected "OFF" Test patter is Off
	Unacceptable	"Error Code"[CR]

9.8.4 CR_VSCALE Command

Command	"CR_VSCALE"[CR]
Details	Get setting stat	us of Vertical Scale Store Mode
	Acceptable	"000_%1[CR]
Response	%1	"-32" ~ "032"
Response	Unacceptable	"Error Code"[CR]

Page 59

9.8.5 CR_VPOS Command

Command	"CR_VPOS"[CR]
Details	Get setting status of Vertical Position Store Mode
Acceptable "000_%1"[CR]		"000_%1"[CR]
Response	%1	"-15" ~ "015"
Response	Unacceptable	"Error Code"[CR]

9.8.6 CR_HSCALE Command

Command	"CR_HSCALE"[CR]
Details	Get setting stat	us of Horizontal Scale Store Mode
	Acceptable	"000_%1"[CR]
Response	%1	"-32" ~ "032"
	Unacceptable	"Error Code"[CR]

9.8.7 CR_HPOS Command

Command	"CR_HPOS"[CR]
Details	Get setting stat	us of Horizontal Position Store Mode
	Acceptable	"000_%1"[CR]
Response	%1	"-15" ~ "015"
	Unacceptable	"Error Code"[CR]

Page 60

9.9 Lamp Status Read Command

9.9.1 CR LAMPREPL Command

Command	"CR_LAMPREPL"[CR]
Details	Get information of Lamp Replacement time
	Acceptable	"000_%1"[CR]
Response	%1	"1Y" Over lamp replacement time "1N" Within lamp replacement time "1" means the number of lamps. (1 lamp model→ "1") "Y"/"N" means if it has reached its replacement time or not. e.g. "1Y"projector is 1 lamp model and Lamp is over its replacement time
	Unacceptable	"Error Code"[CR]

9.9.2 CR_LAMPH Command

Command	"CR_LAMPH"[CR]
Details	Get total running time of lamp by hour (h) *Actual running time, not corresponding value
	Acceptable	"000_%1"[CR]
Response	%1	"00000"~"999999"
Response	Unacceptable	"Error Code"[CR]

9.9.3 CR_LAMPCORRESPH Command

Command	"CR_LAMPCORRESPH"[CR]
Details	Get total runnir * Correspondin	ng time of lamp by hour (h) g value, not actual running time
	Acceptable	"000_%1"[CR]
Response	%1	"00000"~"99999"
	Unacceptable	"Error Code"[CR]

9.9.4 CR LAMPMODE Command

Command	"CR_LAMPMODE"[CR]
Details	Get setting status of Lamp Mode
Response	Acceptable	"000_%1"[CR]
	%1	"NORMAL" Lamp Mode is Normal "ECO" Lamp Mode is Eco
	Unacceptable	"Error Code"[CR]

Page 61

9.9.5 CR_LAMPMSTS Command

Command	"CR_LAMPST	S"[CR]
Details	Get Lighting sta	atus of lamp
	Acceptable	"000_%1"[CR]
Response	%1	"n ***" A number of should be among 1-4. First character shows how many lamps are incorporated in projector. (1,2 or 4) Secound character shows follwing status in order of lamp number. "I" Lamp is ON "O" Lamp is OFF "X" Lamp failure e.g. "11" ······ 1 lamp model and Lamp is ON "2IO······ 2 lamps model and No.1 Lamp is ON and No.2Lamp is OFF "4IOXI" ···· 4 lamps model and No.1,No.4 lamps are ON. No.2 lamp is OFF and No.3 model is failed.
	Unacceptable	"Error Code"[CR]

9.9.6 CR PROJH Command

Command	"CR_PROJH"[CR]
Details	Get total running time of Projector by hour (h)
	Acceptable	"000_%1"[CR]
Response	%1	"0000000"~"0099999"
Response	Unacceptable	"Error Code"[CR]

9.9.7 CR_HMLAMP Command

Command	"CR_HMLAMP"[CR]
Details	Get lamp numb	per.
	Acceptable	"000_%1"[CR]
Response	%1	"001"
Response	Unacceptable	"Error Code" [CR]

Page 62

9.10 Sound Status Read Command

9.10.1 CR VOLUME Command

Command	"CR_VOLUME"[CR]
Details	Get Volume value of user control
Response	Acceptable	"000_%a"[CR]
	%a	"000"~"063"
	Unacceptable	"Error Code" [CR]

9.10.2 CR MUTE Command


Command	"CR_MUTE"[CR]
Details	Get sound mute setting status
Acceptable "000_%a"[CR]		"000_%a"[CR]
Response	%a	"ON" Sound Mute is ON "OFF" Sound Mute is OFF
Response	Unacceptable	"Error Code" [CR]

Page 63

9.11 Setting Status Read Command

9.11.1 CR LANG Command

Command	"CR_LANG"[CR]
Details	Get selected la	inguage
	Acceptable	"000_%a"[CR]
Response	%a	"ENG"
	Unacceptable	"Error Code"[CR]

9.11.2 CR_AUTOSETUPPCADJ Command

Command	"CR_AUTOSETUPPCADJ" [CR]
Details	Get Auto PC adj. setting status in Auto setup
Response	Acceptable	"000_%a"[CR]
	%a	"ON" Auto PC ADJ. in Auto setup is ON "OFF" Auto PC ADJ. in Auto setup is OFF
	Unacceptable	"Error Code"[CR]

9.11.3 CR_AUTOSETUPKEYSTONE Command

Command	"CR_AUTOSETUPKEYSTONE" [CR]
Details	Get Keystone setting status in Auto setup
	Acceptable	"000_%a"[CR]
Response	%a	"AUTO" Auto Keystone is Auto "MANUAL" Auto Keystone is Manual "OFF" Auto Keystone is OFF
	Unacceptable	"Error Code"[CR]

9.11.4 CR INPUTSEARCH Command

Command	"CR_INPUTSEARCH"[CR]
Details	Get setting status of Input search
	Acceptable	"000_%a"[CR]
Response	%a	"OFF" Input search is OFF "ON1" Input search is On1 "ON2" Input search is On2
	Unacceptable	"Error Code"[CR]

Page 64

9.11.5 CR_BACKGND Command

Command	"CR_BACKGND" [CR]
Details	Get setting status of Screen for no signal
	Acceptable	"000_%1" [CR]
Response	%1	"BLUE"Blue Back is selected "USER" User is selected "BLACK" Black Back is selected
	Unacceptable	"Error Code" [CR]

9.11.6 CR_DISP Command

Command	"CR_DISP"[CR]
Details	Get setting status of Display
Response	Acceptable	"000_%a"[CR]
	%a	"ON" Display is ON "OFF" Display is OFF "CNTDWNOFF" Countdown OFF
	Unacceptable	"?"[CR]

9.11.7 CR_LOGO Command

Command	"CR_LOGO"[CR]
Details	Get setting status of Logo
	Acceptable	"000_%1"[CR]
Response	%1	"OFF" Logo function is OFF "DFLT" Default Logo is selected "USER" User Logo is selected
Response	Unacceptable	"?"[CR]

9.11.8 CR USBTERMINAL

Command	"CR_USBTERMINAL" [CR]
Details	Get setting status of USB terminal
Response	Acceptable	"000_%1"[CR]
	%1	"DISPLAY"Display is selected "MOUSE"Mouse control is selected
	Unacceptable	"Error Code" [CR]

9.11.9 CR_CEIL Command

Command	"CR_CEIL" [CR]
Details	Get setting status of Ceiling
Response	Acceptable	"000_%1"[CR]
	%1	"ON" Ceiling is ON "OFF" Ceiling is OFF
	Unacceptable	"Error Code" [CR]

Page 65

9.11.10 CR_REAR Command

Command	"CR_REAR" [CR]
Details	Get setting status of Rear
Response	Acceptable	"000_%1"[CR]
	%1	"ON" Rear is ON "OFF" Rear is OFF
	Unacceptable	"Error Code" [CR]

9.11.11 CR_POINTER Command

Command	"CR_POINTER" [CR]
Details	Get Pointer setting status
	Acceptable	"000_%a"[CR]
Response	%a	"SPOTLIGHTMAX" Spotlight Maximum mode "SPOTLIGHTMID" Spotlight Medium mode "SPOTLIGHTMIN" Spotlight Minimum mode "ARROW" Arrow Mode "FINGER" Finger Mark Mode "LASER" Laser Mark Mode
	Unacceptable	"Error Code" [CR]

9.11.12 CR P-MANE Command

Command	"CR_P-MANE"[CR]
Details	Get Power management setting status
	Acceptable	"000_%a"[CR]
Response	%a	"OFF" Power Management is OFF "READY" Power Management is Ready "SHUTDOWN" Power Management is set to Shut Down mode
Response	Unacceptable	"Error Code" [CR]

9.11.13 CR_P-MANETIME Command

Command	"CR_P-MANETIME"[CR]
Details	Get time to start Power Management
	Acceptable	"000_%a"[CR]
Response	%a	"001"~"030"1 minute to 30 minutes
Response	Unacceptable	"Error Code" [CR]

9.11.14 CR_ON-STA Command

Command	"CR_ON-STA"[CR]
Details	Get Power ON Start setting status
	Acceptable	"000_%a"[CR]
Response	%a	"ON" Power ON Start is ON "OFF" Power ON Start is OFF
	Unacceptable	"Error Code" [CR]

Page 66

9.11.15 CR_STANDBYMODE Command

Command	"CR_STANDBYMODE" [CR]
Details	Get Standby Mode setting status
Response	Acceptable	"000_%a"[CR]
	%a	"ECO" Eco Mode "NORMAL" Normal Mode(Network is selected)
	Unacceptable	"?"[CR]

9.11.16 CR CCAPTIONDISP Command

Command	"CR_CCAPTIONDISP"[CR]
Details	Get selected channel of Closed caption
	Acceptable "000_%a"[CR]
Response		"OFF" Off "CC1" CC1 is selected
	%a	"CC2" CC2 is selected "CC3" CC3 is selected "CC4" CC4 is selected
	Unacceptable	"Error Code"[CR]

9.11.17 CF CCAPTIONCOLOR Command

Command	"CF_CCAPTIONCOLOR_%1"[CR]
Details	Get selected color of Closed caption
	Acceptable	"000"[CR]
Response	%a	"COLOR" Color is selected "WHITE" White is selected
Response	Unacceptable	"Error Code"[CR]

9.11.18 CR RCODE Command


Command	"CR_RCODE"[CR]
Details	Get selected Remote Control Code
	Acceptable	"000_%a"[CR]
Response	%a	"001" Code1 is selected "002" Code2 is selected "003" Code3 is selected "004" Code3 is selected "005" Code5 is selected "006" Code6 is selected "007" Code6 is selected "008" Code8 is selected
	Unacceptable	"Error Code" [CR]

9.11.19 CR SECURITY Command

Command	"CR_SECURITY" [CR]
Details	Get Security Mode setting status
Response	Acceptable	"000_%1[CR]
	%1	"ON" PJ Lock setting on Menu is ON-1 or ON-2 "OFF"PJ Lock setting on Menu is OFF
	Unacceptable	"Error Code" [CR]

Page 67

9.11.20 CR_KEYDIS Command

Command	"CR_KEYDIS"(CR)
Details	Get disablility status of RC/Projector keys (valid or invalid)
Response	Acceptable	"000_%a"[CR]
	%a	"NONE" RC / Projector keys are valid "RC" RC keys are invalid "KEY" Projector keys are invalid
	Unacceptable	"Error Code" [CR]

9.11.21 CR PJLOCKNOW Command

Command	"CR_PJLOCKNOW" [CR]
Details	Get if PJ lock is actually in operation
	Acceptable	"000_%1[CR]
Response	%1	"LOCK" PJ Lock is in operation. PJ Lock status is ON-1 or ON-2 on Menu, and PJ PIN CODE is not entered so that projector is actually locked. "FREE" PJ Lock is released. PJ Lock status is OFF, or, status is ON-1 or ON-2 on Menu but PJ PIN CODE is entered correctly so that PJ Lock is released.
Response	Unacceptable	"Error Code" [CR]

9.11.22 CR PJLOCKMENU Command

Command	"CR_PJLOCKMENU" [CR]
Details	Get status of PJ Lock on Menu
	Acceptable	"000_%1[CR]
Response	%1	"ON1" PJ Lock status is On-1 "ON2" PJ Lock status is On-2 "OFF" PJ Lock status is OFF
	Unacceptable	"Error Code" [CR]

9.11.23 CR FANMODE Command

Command	"CR_FANMODE"[CR]
Details	Get selected Fan mode
Response	Acceptable	"000_%a"[CR]
	%a	"L1" Fan mode is L1 "L2" Fan mode is L2
	Unacceptable	"Error Code" [CR]

9.11.24 CR_FANCONTROL Command

Command	"CR_FANCONTROL"[CR]
Details	Get selected Fan control setting status
Response	Acceptable	"000_%a"[CR]
	%a	"OFF" Fan control is OFF "ON1" Fan control is ON1 "ON2" Fan control is ON2 "ON3" Fan control is ON3
	Unacceptable	"Error Code" [CR]

Page 68

9.11.25 CR_FILH Command

Command	"CR_FILH"[CR]
Details	Get Filter used time
Response	Acceptable	"000_%1"[CR]
	%1	"00000"~"99999" 0 hour to 99999 hours
	Unacceptable	"Error Code"[CR]

9.11.26 CR_FILREPL Command

Command	"CR_FILREPL"[CR]
Details	Get the information of Filter replacement time
Response	Acceptable	"000_%1"[CR]
	%1	"1Y" Over filter replacement time "1N" Within filter replacement time
	Unacceptable	"Error Code"[CR]

9.11.27 CR_FILTIMER Command

Command	"CR_FILTIMER" [CR]
Details	Get setting time which filter warning OSD is displayed
	Acceptable	"000_%1"[CR]
Response	%1	"100" 100 hours "200" 200 hours "300" 300 hours "OFF" No OSD display
	Unacceptable	"Error Code"[CR]

Page 69

9.12 Other Status Read Command

9.12.1 CR STATUS Command

Command	"CR_STATUS"(CR)
Details	Get status of Projector behavior. This command affects the same as "CR0" of Basic Serial command, but this has an error code.
	Acceptable	"000_%1"[CR]
Response	%1	"00"= Power ON "80"= Stand by "40"= Count down "20"= Cooling down "10"= Power failure "28"= Cooling down due to abnormal temperature "88"= Stand by after Cooling down "24"= Power saving cooling down "04"= Power saving "21"= Cooling down due to Lamp failure "81"= Stand by after Cooling down due to Lamp failure
Response	Unacceptable	"Error Code"[CR]

9.12.2 CR_SIGNAL Command

Command	"CR_SIGNAL"(CR)
Details	Get Signal status if there is signal or not
Response	Acceptable	"000_%a"[CR]
	%a	"ON" Signal is found "OFF" There is no signal
	Unacceptable	"Error Code" [CR]

9.12.3 CR_VMUTE Command

Command	"CR_VMUTE"[CR]
Details	Get setting status of No Show
Response	Acceptable	"000_%a"[CR]
	%a	"ON" No Show is ON, User Logo (My picture) is displayed "OFF" No Show is OFF
	Unacceptable	"Error Code" [CR]

9.12.4 CR_FREEZE Command

Command	"CR_FREEZE"[CR]
Details	Get setting status of Freeze
Response	Acceptable	"000_%a"[CR]
	%a	"ON" Freeze is ON "OFF" Freeze is OFF
	Unacceptable	"Error Code" [CR]

Page 70

9.12.5 CR_PTIMER Command

Command	"CR_PTIMER"[CR]
Details	Get status of Presentation Timer
Response	Acceptable	"000_%a"[CR]
	%a	"ON" Presentation timer is in operation "STOP" Presentation timer is paused "OFF" Presentation timer is not operating
	Unacceptable	"Error Code" [CR]

9.12.6 CR_TEMPWARN Command

Command	"CR_TEMPWARN"[CR]
Details	Get the temperature inside a projector and its condition if it is abnormal temperature or close to abnormal temperature If there are several sensors installed, it is possible to get information from all the sensors at once.
	Acceptable	"000_%a_%b_%c"[CR]
Response	%a %b %c	%a Sensor 1 status %b Sensor 2 status %c Sensor 3 status "W" Approach or reach abnormal temperature (dangerous temperature) "S" Far from abnormal temperature (safe temperature) "N" Sensor detects no abnormal temperature [Example] "S_W_S"[CR] means Sensor 1 detects safe temperature, Sensor 2 detects abnormal temperature and Sensor 3 detects safe temperature Note) When the temperature difference between Sensor 1 and 3 reaches specific value, some of the models detect it as Abnormal temperature difference between Sensor 1 and 3 reaches specific value, some of the models detect it the temperature difference between Sensor 1 and 3 is dangerous state or not. The 3rd data means temperature abnormality due to Sensor 3 When abnormal temperature abnormality) is returned.
	Unacceptable	"Error Code" [CR]

Page 71

9.12.7 CR_TEMP Command

Command	"CR_TEMP"[C	R]
Details	Get current temperature inside a projector. If there are several sensors installed, it is possible to get information from all the sensors at once.
	Acceptable	"000_%1_%2_%3"[CR]
Response	%1,%2,%3	"000_%1_%2_%3"[CR] %1= Sensor 1 temperature (Outside temperature) %2= Sensor 2 temperature (Inside temperature1) %3= Sensor 3 temperature (Inside temperature2) %1,%2 are consists of 6 bites fixed There must be 1 space between %1 and %2, and, %2 and %3 e.g31.5F "_" means a space and "_" changes into "-", when temperature gets below freezing. e.g05.5F The last character shows if corresponding sensor is under abnormal temperature. "F" Abnormal temperature "W"Close to abnormal temperature(Temperature is as high to display Warning) "S"Not close to abnormal temperature (Temperature is low enough and safe.) "N"Applicable sensor does not detect abnormal temperature
	%1,%2,%3	When several sensors are incorporated, projector returns values continuously. e.g. "_31.5F35.2S38.0W"[CR] A data of sensor 1 comes first and a data of sensor 2 follws after 1 space. As described respectively in e.g., sensor 1 detects abnormal temp., sensor 2 detects 35.2 degrees which means safety, and sensor 3 is 38 degrees which is close to abnormal temp. In case projector cannot return its data due to some hard ware failure, the last character becomes "E" such as "_00.0E". Some of the projectors get abnormal temperature because of heat of Lamp ballast in Standby mode or Powering ON. Therefore detection of abnormal temperature is suspended while Standby mode or adequate time after Power ON, and during that time projector returns "N" as a temperature data.
	Unacceptable	"Error Code"[CR]

Page 72

9.12.8 CR_TEMPFAIL Command

Command	"CR_TEMPFA	L"[CR]
Details	Get the temperature inside a projector when abnormal temperature occurs. If there are several sensors installed, it is possible to get information from all the sensors at once.
	Acceptable	"000_%a_%b_%c"[CR]
Response	%a %b %c	%a Sensor 1 temp. (External temp.) %b Sensor 2 temp. (Internal temp.1) %c Sensor 3 temp. (Internal temp.2) [Example] "_31.5F"[CR] "_" indicates a space. When the temperature sinks to -, the first character is "." like "-05.5F"[CR] The last character means the sensor's status if it reaches abnormal temperature Exceeding critical temp
	Unacceptable	"Error Code" [CR]