Sanyo PLC-XP40L, PLC XP45L User Manual

Owner’s Manual

PLC-XP40L

Multimedia Projector

MODEL

PLC-XP45L

✽ Projection lens is optional.

2

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE
OWNER'S MANUAL WITH THIS UNIT.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Before operating this projector, read this manual thoroughly and operate the projector properly.
This projector provides many convenient features and functions. Operating the projector properly enables you to
manage those features and maintains it in better condition for a considerable time.
Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other
accidents.
If your projector seems to operate improperly, read this manual again, check operations and cable connections and try
the solutions in the “Trouble-shooting” section of the end of this booklet. If the problem still persists, contact the sales
dealer where you purchased the projector or the service center.

TO THE OWNER

SAFETY PRECAUTIONS

WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

● This projector produces intense light from the projection lens. Do not stare directly into the lens as possible.
Eye damage could result. Be especially careful that children do not stare directly into the beam.

● This projector should be set in the way indicated. If not, it may result in a fire hazard.

● Take appropriate space on the top, sides and rear of the projector

cabinet for allowing air circulation and cooling the projector.
Minimum distance should be taken. If the projector is to be built
into a compartment or similarly enclosed, the minimum distances
must be maintained. Do not cover the ventilation slot on the
projector. Heat build-up can reduce the service life of your
projector, and can also be dangerous.

● Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation
holes.

● Remote Control Unit, supplied to this projector, emits the laser beam as the laser pointer function from Laser
Light Window while pressing LASER button (for 1 minute / LASER POINTER INDICATOR lights red to indicate
laser emission). Do not look into Laser Light Window or shine the laser beam on yourself or other people. Eye
damage may result.

● If the projector is not to be used for an extended time, unplug the projector from the power outlet.

READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.

SIDE and TOP REAR

20cm

50cm 50cm

50cm

3

SAFETY INSTRUCTIONS

All the safety and operating instructions should be read before
the product is operated.

Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.

Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm,

or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.

Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...

Do not use attachments not recommended by the
manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.

An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.

Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.

The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.

This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.

Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.

This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.

Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.

Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.

Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the

operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.

e. If the projector has been dropped or the cabinet has been

damaged.

f. When the projector exhibits a distinct change in

performance-this indicates a need for service.

When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask
the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.

4

COMPLIANCES

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada :

AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the
plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be
unable to insert the plug into the outlet, contact your electrician.

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

AC POWER CORD REQUIREMENT

Federal Communication Commission Notice

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures :

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such

changes or modifications should be made, you could be required to stop operation of the equipment.
Model Number : PLC-XP40L/PLC-XP45L

Trade Name : Sanyo
Responsible party : SANYO FISHER COMPANY
Address : 21605 Plummer Street, Chatsworth, California 91311

Telephone No. : [phone]

GROUND

5

TABLE OF CONTENTS

FEATURES AND DESIGN 6

BEFORE OPERATION 14

COMPUTER MODE 22

VIDEO MODE 30

SETTING 35

APPENDIX 37

PREPARATION 7

NAME OF EACH PART OF PROJECTOR 7
SETTING-UP PROJECTOR 8

CONNECTING AC POWER CORD 8
LENS INSTALLATION 9
POSITIONING PROJECTOR 9
LENS SHIFT ADJUSTMENT 9
ADJUSTABLE FEET 10
MOVING PROJECTOR 10

CONNECTING PROJECTOR 11

TERMINALS OF PROJECTOR 11
CONNECTING TO COMPUTER 12
CONNECTING TO VIDEO EQUIPMENT 13

OPERATION OF REMOTE CONTROL 14

LASER POINTER FUNCTION 14
REMOTE CONTROL BATTERIES INSTALLATION 15

TOP CONTROLS AND INDICATORS 16
OPERATING ON-SCREEN MENU 17

HOW TO OPERATE ON-SCREEN MENU 17
FLOW OF ON-SCREEN MENU OPERATION 17
MENU BAR 18

SELECTING INPUT SOURCE 22
SELECTING COMPUTER SYSTEM 22
PC ADJUSTMENT 23

AUTO PC ADJUSTMENT 23
MANUAL PC ADJUSTMENT 24
COMPATIBLE COMPUTER SPECIFICATIONS 26

PICTURE IMAGE ADJUSTMENT 27

IMAGE LEVEL SELECT 27
IMAGE LEVEL ADJUSTMENT 28

PICTURE SCREEN ADJUSTMENT 29

SELECTING INPUT SOURCE 30
SELECTING VIDEO SYSTEM 31
PICTURE IMAGE ADJUSTMENT 32

IMAGE LEVEL SELECT 32
IMAGE LEVEL ADJUSTMENT 33

PICTURE SCREEN ADJUSTMENT 34

SETTING MENU 35

OPERATING WIRELESS MOUSE 37
MAINTENANCE 38

WARNING TEMP. INDICATOR 38
AIR FILTER CARE AND CLEANING 38
CLEANING PROJECTION LENS 38
LAMP REPLACEMENT 39
LAMP REPLACE COUNTER 39

TROUBLESHOOTING 40
TECHNICAL SPECIFICATIONS 42

BASIC OPERATION 19

TURNING ON / OFF PROJECTOR 19
ADJUSTING SCREEN 20

ZOOM ADJUSTMENT 20
FOCUS ADJUSTMENT 20
LENS SHIFT ADJUSTMENT 20
KEYSTONE ADJUSTMENT 20
PICTURE FREEZE FUNCTION 21
NO SHOW FUNCTION 21
P-TIMER FUNCTION 21

SOUND ADJUSTMENT 21

TRADEMARKS

● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.

● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.

● Windows and PowerPoint are registered trademarks of Microsoft Corporation.

● Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its

respective corporation.

6

FEATURES AND DESIGN

This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This
projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD)
technology.

◆ Compatibility

This projector widely accepts various video and
computer input signals including;

● Computers

IBM-compatible or Macintosh computer up to 1280
x 1024 resolution.

● 6 Color Systems

NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL­N color system can be connected.

● Component Video

Component video signal, such as a DVD player
output high definition TV signals including 480i,
480p, 575i, 575p, 720p, 1035i or 1080i, can be
connected.

● S-Video

S-Video signal, such as a S-VHS VCR output
signal, can be connected.

◆ High Resolution Image

This projector provides 1024 x 768 dots resolution for
computer input and 800 horizontal TV lines. Resolution
from a computer between XGA (1024 x 768) and SXGA
(1280 x 1024) is compressed into 1024 x 768 dots. This
projector cannot display image of over 1280 x 1024 dots.
When resolution of your computer is over than 1280 x
1024, reset a computer output for lower resolution.

◆ Multi-Scan System

This projector has Multi-Scan System to conform to
almost all computer output signals quickly. There is no
need for troublesome manual adjustment of frequency
and other settings.

◆ Keystone Correction

Positioning height of a projector may result in distorted
image being displayed in a trapezoid shape. Keystone
Correction solves this problem by digitally altering
projection to produce undistorted images.

◆ Multilanguage Menu Display

Operation menu is displayed in; English, German,
French, Italian, Spanish, Portuguese, Dutch, Swedish,
Chinese, Korean or Japanese.

◆ One-Touch Auto PC Adjustment

Incoming computer video signals are recognized and
best adjustment is automatically set by Auto PC
Adjustment. No complicated setup is necessary and
projection is always precise.

◆ Digital Zoom (for Computer)

Digital Zoom function adjusts image size to approx. 1/4 ~
49 times of original image size, allowing you to focus on
crucial information at a presentation.

◆ Compact Design

This projector is extremely compact in size and weight.
It is designed to carry and work anywhere you wish to
use.

◆ Power Management

Power Management function is provided to reduce power
consumption while a projector is not in use.
This Power Management function operates to turn
Projection Lamp off when a projector detects signal
interruption and any button is not pressed over 5
minutes. Projection Lamp is automatically turned on
again when a projector detects signal or any operation
button is pressed.
This projector is shipped with this function ON.

◆ Wireless Mouse

Remote Control Unit supplied with this projector has
Wireless Mouse function for a connected computer. This
function enables you to operate both projector and
computer with Remote Control Unit only.

◆ Digital Visual Interface

This projector is equipped with DVI 24-pin terminal for
connecting DVI output from a computer.

◆ Laser Pointer Function

Remote Control Unit supplied with this projector includes
Laser Pointer function. This function helps you to make
a smart presentation on a projected screen.

◆ Motor-driven Lens Shift

Projection lens can be moved up and down with motor­driven lens shift function. This function makes it easy to
provide projected image where you want.
Zoom and focus can be also adjusted with motor-driven
operation.

7

PREPARATION

NAME OF EACH PART OF PROJECTOR

BOTTOM OF CABINET

BACK OF CABINET

HOT AIR EXHAUSTED !

Air blown from exhaust vent is hot. When
using or installing a projector, following
precautions should be taken.

● Do not put a flammable object near this vent.

● Keep rear grills at least 3’(1 m) away from

any object, especially heat-sensitive object.

● Do not touch this area, especially screws
and metallic parts. This area will become
hot while a projector is used.

This projector detects internal temperature
and automatically controls operating power
of Cooling Fans.

FRONT OF CABINET

LAMP COVER

ADJUSTABLE FEET

AND

FEET LOCK LATCHES

This projector is equipped with cooling
fans for protection from overheating.
Pay attention to following to ensure
proper ventilation and avoid a possible
risk of fire and malfunction.

● Do not cover vent slots.

● Keep side clear of any objects.

Obstructions may block cooling air.

AIR INTAKE VENTS

PROJECTION LENS

SPEAKERS

INFRARED

REMOTE RECEIVER

LENS COVER

POWER CORD

CONNECTOR

EXHAUST VENT

TERMINALS

AND CONNECTORS

TOP CONTROLS

AND INDICATORS

INFRARED

REMOTE RECEIVER

CARRYING

HANDLE

AIR INTAKE

VENT

NOTE ON POWER CORD

AC Power Cord must meet requirement of country where you use a projector.
Confirm an AC plug type with chart below and proper AC Power Cord must be used.
If supplied AC Power Cord does not match your AC outlet, contact your sales dealer.

SETTING-UP PROJECTOR

8

PREPARATION

To POWER CORD
CONNECTOR on your
projector.

Projector side AC Outlet side

Ground

To the AC Outlet.

(120 V AC)

For Continental Europe

For the U.S.A. and Canada

This projector uses nominal input voltages of 100-120 V or 200-240
V AC. This projector automatically selects correct input voltage. It
is designed to work with single-phase power systems having a
grounded neutral conductor. To reduce risk of electrical shock, do
not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure
of type of power supply being in use.
Connect a projector with a peripheral equipment before turning a
projector on. (Refer to pages 11 ~ 13 for connection.)

CAUTION

For safety, unplug AC Power Cord when an appliance is not
used.
When this projector is connected to outlet with AC Power Cord,
an appliance is in Stand-by Mode and consumes a little electric
power.

CONNECTING AC POWER CORD

Connect AC Power Cord (supplied) to a projector.
AC outlet must be near this equipment and must
be easily accessible.

For the U.K.

To the AC Outlet.

(200 - 240 V AC)

To the AC Outlet.

(200 - 240 V AC)

9

PREPARATION

Projection lens can be moved up and down with motor-driven lens shift function. This function makes it easy to
provide projected image where you want. U/D ratio can be adjusted 10 : 0 ~ 1 : 1 (refer to figure below.). Refer
to P 20 for operation.

Highest (10 : 0) Lowest (1 : 1)

POSITIONING PROJECTOR

LENS SHIFT ADJUSTMENT

This projector is designed to project on a flat projection
surface.

ROOM LIGHT

Brightness in a room has a great influence on picture
quality. It is recommended to limit ambient lighting in
order to provide best image.

SCREEN

Before setting up a projector, install Projection Lens on
Projector.

1. Before installation, check where a projector is used and
prepare suitable lens. For specifications of a Projection Lens,
contact sales dealer where you purchased a projector.

2. For installation, refer to installation manual in the optional
lens.

LENS INSTALLATION

COVER CAP

When install the lens, remove the cover cap in the projector.

NOTE;

1

10 : 0

1

10

PREPARATION

CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR

● Do not drop or bump a projector, otherwise damages or malfunctions may result.

● When carrying a projector, use a suitable carrying case.

● Do not transport a projector by using a courier or transport service in an unsuitable transport case. This

may cause damage to a projector. To transport a projector through a courier or transport service, consult
your dealer for best way.

MOVING PROJECTOR

Use Carry Handle when moving a Projector.
When moving a projector, replace lens cover and retract
feet to prevent damage to lens and cabinet.
When this projector is not in use for an extended period,
put it into case (dust cover) supplied with this projector.

ADJUSTABLE FEET

Picture tilt and projection angle can be adjusted by
rotating ADJUSTABLE FEET. Projection angle can be
adjusted to 10.5 degrees.

Lift front of a projector and pull FEET LOCK LATCHES
on both sides of a projector.

1

ADJUSTABLE FEET FEET LOCK

LATCHES

Release FEET LOCK LATCHES to lock ADJUSTABLE
FEET and rotate ADJUSTABLE FEET to fine tune
position and tilt.

2

To shorten ADJUSTABLE FEET, lift front of a projector
and pull and undo FEET LOCK LATCHES.

Position and keystone distortion of image can be adjusted
using Menu Operation. (Refer to P 20 and 35.)

3

11

CONNECTING PROJECTOR

TERMINALS OF PROJECTOR

When controlling computer
with Remote Control Unit of
this projector, connect mouse
port of your personal computer
to this connector. (Refer to
P12.)

Connect S-VIDEO
output from video
equipment to this
jack. (Refer to P13.)

Connect an audio output
(stereo) from computer to
these jacks.
(Refer to P12.)

Connect an audio output
from video equipment to
these jacks.
(Refer to P13.)

CONTROL PORT CONNECTOR

COMPUTER AUDIO

INPUT (1 and 2) JACKS

AUDIO INPUT JACKS

VIDEO INPUT JACKS

S-VIDEO INPUT JACK

Connect composite video
output from video equipment
to VIDEO/Y jack or connect
component video outputs to
VIDEO/Y, Cb/Pb and Cr/Pr
jacks. (Refer to P13.)

Connect computer (digital/analog)
output to one of these terminals.
(Refer to P12.)

COMPUTER INPUT

TERMINALS (DIGITAL/ANALOG)

This projector has input and output terminals on its back for connecting computers and video equipment. Refer to figures on
pages 11 to 13 and connect properly.

This projector uses a micro processor
to control this unit, and occasionally,
this micro processor may malfunction
and need to be reset. This can be
done by pressing RESET button with a
pen, which will shut down and restart
unit. Do not use RESET function
excessively.

RESET BUTTON

When controlling computer with
Remote Control Unit of this
projector, connect mouse port
of your personal computer to
this terminal. (Refer to P12.)

USB CONNECTOR (Series B)

✽ Do not press this button. This button

is used for our optional accessories.

Connect component video
output (Y, Cb, Cr or Y, Pb, Pr)
from video equipment to
VIDEO/Y, Cb/Pb and Cr/Pr
jacks or connect computer
output {5 BNC Type (Green,
Blue, Red, Horiz. Sync and
Vert. Sync.)} from computer
to G, B, R, H/V and V jacks.
(Refer to P12 and 13.)

5 BNC INPUT JACKS

When using Wired/Wireless
Remote Control Unit as Wired
Remote Control, Connect
Wired Remote Control Unit to
this jack with Remote Control
Cable (supplied).

R/C JACK

INPUT 1

ANALOG DIGITAL(DVI-D)

RESET

USB

AUDIO 1 AUDIO 2

G B R H/V V

VIDEO/Y Cb/Pb Cr/Pr

VIDEO/Y Cb/Pb Cr/Pr

INPUT 2

INPUT 3

R–AUDIO –L

(

MONO

R/C JACK

CONTROL PORT

S–VIDEO

)

12

CONNECTING PROJECTOR

CONNECTING TO COMPUTER

IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)

VGA Cable

Monitor Output

Desktop type

Laptop type

Control Cable

for Serial Port ✽

Terminal

Serial port PS/2 portAudio Output

CONTROL

PORT

COMPUTER

AUDIO IN 1 or 2

COMPUTER IN ANALOG

Use one of these Control
Cables corresponding with
terminal of your computer.

ADB port

Cables used for connection (✽ = Cable or adapter is not supplied with this projector.)

Control Cable

for PS/2 Port

Control Cable

for ADB Port

✽

Audio
Cable

✽

(stereo)

NOTE :

When connecting cable, power cords of both
a projector and external equipment should
be disconnected from AC outlet. Turn a
projector and peripheral equipment on
before computer is switched on.

USB port

MAC Adapter

Set slide switches
according to chart
below.

• VGA Cable (HDB 15 pin)

• DVI-Digital Cable (for Single Link T.M.D.S.)

✽

• BNC Cable ✽

• Control Cable for PS/2 Port, Serial Port or ADB Port

• USB Cable ✽

• MAC Adapter (When connecting to Macintosh computer)

• Audio Cables (RCA x 2 and Mini Plug (stereo) x 1)

✽

Terminals

of a Projector

Terminal

Terminal

DVI
Cable

✽

Monitor Output

USB

COMPUTER IN DIGITAL

Set switches as shown in table
below depending on RESOLU­TION MODE that you want to use
before you turn on projector and
computer.

◆ MAC ADAPTER

USB
Cable

✽

BNC
Cable

✽

INPUT 1

ANALOG DIGITAL(DVI-D)

RESET

USB

AUDIO 1 AUDIO 2

GBRH/VV

VIDEO/Y Cb/Pb Cr/Pr

VIDEO/Y Cb/Pb Cr/Pr

INPUT 2

INPUT 3

R–AUDIO–L

(

MONO

R/C JACK

CONTROL PORT

S–VIDEO

)

13" MODE (640 x 480)
16" MODE (832 x 624)
19" MODE (1024 x 768)

123456

OFF OFF OFF OFF

ON

OFF

OFFON ON

ON ON
ON ON

OFF OFF OFF

OFFOFF OFF OFF

ON

1

OFF OFFON ONON ON21" MODE (1152 x 870)

2 3 4 5 6

DIP

13

CONNECTING PROJECTOR

CONNECTING TO VIDEO EQUIPMENT

Video Source (example)

Video Cassette Recorder Video Disc Player

S-VIDEO
Cable ✽

Terminals

of a Projector

S-VIDEO Output

Cables used for connection (✽ = Cable is not supplied with this projector.)

• Video Cable (RCA x 1 or RCA x 3)

✽

• BNC Cable ✽

• S-VIDEO Cable ✽

• Audio Cable (RCA x 2) ✽

NOTE :
When connecting cable, power cords of
both a projector and external equipment
should be disconnected from AC outlet.

Audio Cable
(RCA x 2) ✽

AUDIO IN

S-VIDEO

Y - Cb/Pb - Cr/Pr

VIDEO

Component video output equipment.

(such as DVD player or high-definition TV source.)

Composite

Video Output

Component Video Output

(Y, Cb/Pb, Cr/Pr)

Component Video Output

(Y, Cb/Pb, Cr/Pr)

Y - Cb/Pb - Cr/Pr

Video Cables
(RCA x 1 or

RCA x 3

) ✽

BNC Cable ✽

Audio Output

Composite

Video Output

VIDEO

INPUT 1

ANALOG DIGITAL(DVI-D)

RESET

USB

AUDIO 1 AUDIO 2

G B R H/V V

VIDEO/Y Cb/Pb Cr/Pr

VIDEO/Y Cb/Pb Cr/Pr

INPUT 2

INPUT 3

R–AUDIO–L

(

MONO

R/C JACK

CONTROL PORT

S–VIDEO

)

14

BEFORE OPERATION

OPERATION OF REMOTE CONTROL

ALL-OFF SWITCH

Left Side

When using Remote Control Unit,
turn this switch to “ON.” And turn it
to “ALL OFF” when it is not used.

This Remote Control Unit emits a laser beam as laser pointer function from Laser Light Window. When LASER button is
pressed, laser light goes on. And when LASER button is being pressed for more than 1 minute or LASER button is released,
light goes off. LASER POINTER INDICATOR lights RED and Laser is emitted with RED light to indicate laser beam is being
emitted.
Laser emitted is a class

II laser; therefore, do not look into Laser Light Window or shine laser beam on yourself or other

people. Three marks bellow are caution labels for laser beam.
CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result

hazardous radiation exposure.

Laser Light Window

These caution labels are put on remote control.

LASER POINTER FUNCTION

Used to select input source.
(P22)

Used to execute item
selected, or to expand
or compress image in
DIGITAL ZOOM +/–
mode. (P29)
It is also used as a PC
mouse in Wireless
Mouse Operation. (P37)

POWER ON-OFF BUTTON

Used to turn projector on or
off. (P19)

MENU BUTTON

Used to select MENU
operation. (P17, 18)

INPUT BUTTON

LASER BUTTON

Used to operate Laser Pointer
Function. Laser beam is
emitted while pressing this
button within 1 minute.
When using this Laser Pointer
for more than 1 minute, release
LASER button and press it
again.

Used to move a pointer on ON­SCREEN MENU, adjust each
item, or pan image in DIGITAL
ZOOM +/– mode. (P29)
It is also used as a PC mouse
in Wireless Mouse Operation.
(P37)

✽ When pressing center of this

button, it works as SELECT
button.

POINT BUTTON

Used as a PC mouse in
Wireless Mouse Operation.
(P37)

RIGHT CLICK BUTTON

Used to operate P-TIMER
function. (P21)

Lights red while laser beam
is emitted from Laser Light
Window.

LASER POINTER INDICATOR

P-TIMER BUTTON

LASER POINTER INDICATOR

SELECT BUTTON

ON

ALL OFF

ZOOM

LOCK

MUTE

MENU

NO SHOW

AUTO PC ADJ .

FOCUS

D.ZOOM

LASER

KEYSTONE

P-TIMER

ON-OFF

VOLUME

INPUT

LENS SHIFT

FREEZE

IMAGE

15

BEFORE OPERATION

To insure safe operation, please observe following precautions :

● Use (2) AA, UM3 or R06 type alkaline batteries.

● Replace two batteries at same time.

● Do not use a new battery with an used battery.

● Avoid contact with water or liquid.

● Do not expose Remote Control Unit to moisture, or heat.

● Do not drop Remote Control Unit.

● If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries.

● Danger of explosion if battery is incorrectly replaced.

● Dispose of used batteries according to batteries manufacturers instructions and local rules.

Press lid down­ward and slide it.

Remove battery
compartment lid.

Slide batteries into
compartment.

Replace compartment lid.

Two AA size batteries

For correct polarity (+ and
–), be sure battery
terminals are in contact
with pins in compartment.

Remote Control Batteries Installation

1

2

3

Operating Range

Point Remote Control Unit toward
projector (Receiver Window)
whenever pressing any button.
Maximum operating range for
Remote Control Unit is about 16.4’
(5m) and 60° in front and rear of a
projector.

16.4’
(5 m)

60°

16.4’
(5 m)

Used to adjust zoom.
(P20)

MUTE BUTTON

Used to mute sound.(P21)

ZOOM BUTTON

FOCUS BUTTON

Used to adjust focus.
(P20)

NO SHOW BUTTON

Used to turn picture into
black image. (P21)

AUTO PC ADJ. BUTTON

Use to operate AUTO PC
Adjustment function. (P23)

VOLUME BUTTON

Used to adjust volume.
(P21)

D.ZOOM BUTTON

Used to select DIGITAL
ZOOM +/– mode and
resize image. (P29)

KEYSTONE BUTTON

Used to correct
keystone distortion.
(P20, 35)

FREEZE BUTTON

Used to freeze picture.
(P21)

IMAGE BUTTON

Used to select image
level. (P27, 32)

60°

LENS SHIFT BUTTON

Used to select LENS
SHIFT function. (P20)

WIRED REMOTE JACK

When using as Wired
Remote Control, connect
Remote Control Cable to
this jack.
Battery installation is
required when using as
Wired Remote Control.

ZOOM

LOCK

MUTE

MENU

NO SHOW

FOCUS

D.ZOOM

LASER

KEYSTONE

ON-OFF

VOLUME

INPUT

LENS SHIFT

FREEZE

AUTO PC ADJ .

IMAGE

P-TIMER

16

BEFORE OPERATION

TOP CONTROLS AND INDICATORS

Used to open or close
MENU operation. (P17,

18)

MENU BUTTON

IMAGE BUTTON

READY INDICATOR

SELECT BUTTON

POWER ON–OFF BUTTON

INPUT BUTTON

WARNING TEMP. INDICATOR

LAMP INDICATOR

POINT (VOLUME + / – ) BUTTONS

LAMP REPLACE INDICATOR

Used to select image
level. (P27, 32)

Lights green when a
projector is ready to be
turned on. And it
flashes green in Power
Management mode.
(P36)

Becomes dim when a
projector is turned on.
And bright when a
projector is in stand-by
mode.

Turns to yellow when
life of projection lamp
draws to an end. (P39)

Flashes red when
internal projector
temperature is too
high. (P38)

Used to select input
source. (P22)

Used to select an item or adjust
value in ON-SCREEN MENU. They
are also used to pan image in
DIGITAL ZOOM

+/– mode. (P29)

POINT LEFT/RIGHT buttons are
also used as VOLUME +/– buttons.

Used to execute item
selected. It is also used
to expand / compress
image in DIGITAL
ZOOM mode. (P29)

Used to turn a projector
on or off. (P19)

Used to adjust zoom.
(P20)

FOCUS BUTTON

Used to adjust focus.
(P20)

ZOOM BUTTON

This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top.

LENS SHIFT BUTTON

Used to select LENS
SHIFT function. (P20)

AUTO PC ADJ. BUTTON

Used to operate AUTO PC
Adjustment function. (P23)

17

HOW TO OPERATE ON-SCREEN MENU

FLOW OF ON-SCREEN MENU OPERATION

Display ON-SCREEN MENU

Press MENU button to display ON-SCREEN MENU (MENU
BAR). A red frame is POINTER.

Move POINTER (red frame) to MENU ICON that you want to
select by pressing POINT RIGHT / LEFT buttons.

Adjust ITEM DATA by pressing POINT RIGHT / LEFT
buttons.
Refer to following pages for details of respective
adjustments.

Press POINT DOWN button and move POINTER (red frame
or red arrow) to ITEM that you want to adjust, and then press
SELECT button to show ITEM DATA.

Select Menu to be adjusted

Control or adjust item through ON-SCREEN MENU

1

2

4

3

You can control and adjust this projector through ON-SCREEN
MENU. Refer to following pages to operate each adjustment on
ON-SCREEN MENU.

2 MOVING POINTER

3 SELECT ITEM

Move pointer (✽ see below) or adjust value of item by pressing
POINT button(s) on Top Control or on Remote Control Unit.

Select item or set selected function by pressing SELECT button.

OPERATING ON-SCREEN MENU

✽ Pointer is icon on ON-SCREEN MENU to select item. See fig-

ures on section "FLOW OF ON-SCREEN MENU OPERATION"
below.

Used to select item.

SELECT BUTTON

Used to move Pointer
UP/ DOWN/ RIGHT/
LEFT.

POINT BUTTONS

TOP CONTROL

MENU BAR

POINTER
(red frame)

MENU ICON

ITEM DATA
Press POINT LEFT/RIGHT
buttons to adjust value or
set function.

SELECT

BUTTON

POINTER (red frame)
Press POINT DOWN button to
move POINTER.

1 DISPLAY MENU

Press MENU button to display ON-SCREEN MENU.

ITEM

Used to select item.

SELECT BUTTON

Used to move Pointer
UP/ DOWN/ RIGHT/
LEFT.

POINT BUTTON

WIRELESS REMOTE CONTROL

18

BEFORE OPERATION

MENU BAR

PC SYSTEM MENU

Used to select
computer system.
(Refer to P22, 23)

IMAGE ADJUST MENU

Used to adjust
computer image.
[Contrast / Brightness
/ White Balance
(R/G/B) / Gamma]
(Refer to P28)

SETTING MENU

Used to change
settings of projector
or reset Lamp
Replace Counter.
(Refer to P35,-37)

SOUND MENU

Used to adjust
volume or mute
sound.
(Refer to P21)

IMAGE SELECT MENU

Used to select
image level among
Standard, Real
and Image 1 ~ 4.
(Refer to P27)

FOR PC SOURCE

Press MENU BUTTON while connecting to PC input source.

AV SYSTEM MENU

Used to select
system of selected
video source.
(Refer to P31)

IMAGE ADJUST MENU

Used to adjust picture image.

[Contrast / Brightness / Color /
Tint / White balance (R/G/B) /
Sharpness / Gamma/Noise
Reduction/Progressive]

(Refer to P33, 34)

FOR VIDEO SOURCE

Press MENU BUTTON while connecting to VIDEO input source.

Same function as
Menu for PC source.

INPUT MENU

Used to select
input source
(Input 1, Input 2
or Input 3).
(Refer to P30)

PC ADJUST MENU

Used to adjust
parameters to
match with input
signal format.
(Refer to P23-25)

IMAGE SELECT MENU

Used to select image
level among
Standard, Cinema
and Image 1 ~ 4.
(Refer to P32)

SCREEN MENU

Used to set size of
image to Normal
or Wide.
(Refer to P34)

GUIDE WINDOW

Shows selected
item of ON­SCREEN MENU.

Same function as
Menu for PC source.

INPUT MENU

Used to select
input source (Input
1, Input 2 or Input

3). (Refer to P22)

SCREEN MENU

Used to adjust size
of image. [Normal
/ True / Wide /
Digital zoom +/–]
(Refer to P29)

19

BEFORE OPERATION

TURNING ON PROJECTOR

Connect a projector's AC Power Cord into an AC outlet. LAMP
Indicator lights RED, and READY Indicator lights GREEN.

Press POWER ON-OFF button on Top Control or on Remote
Control Unit to ON. LAMP Indicator dims, and Cooling Fans
start to operate. Preparation Display appears on a screen and
count-down starts. Signal from PC or Video source appears
after 30 seconds.

2

3

TURNING OFF PROJECTOR

Press POWER ON-OFF button on Top Control or on Remote
Control Unit, and a message "Power off?" appears on a screen.

Press POWER ON-OFF button again to turn off projector. LAMP
Indicator lights bright and READY Indicator turns off. After
projector is turned off, Cooling Fans operate (for 90 seconds).
During this "Cooling Down" period, this appliance cannot be
turned on.

1
2

TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE
TURNING IT OFF.

TURNING ON / OFF PROJECTOR

When WARNING TEMP. Indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on
projector again.
When WARNING TEMP. Indicator continues to flash, follow procedures below:

1. Press POWER ON-OFF button to turn a projector off and disconnect AC Power Cord from an AC outlet.

2. Check Air Filters for dust accumulation.

3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 38.)

4. Turn a projector on again.
If WARNING TEMP. Indicator should still continue to flash, contact sales dealer where you purchased this projector or

service center.

1

Complete peripheral connections (with Computer, VCR, etc.)
before turning on projector. (Refer to "CONNECTING TO
PROJECTOR" on pages 11~13 for connecting that equipment.)

3

When projector has cooled down, READY Indicator lights
GREEN again and you can turn projector on. After cooling down
completely, disconnect AC Power Cord.

30

Preparation Display disappears after 30 seconds.

Power off?

Message disappears after 4 seconds.

When “Power Management” function is ON, projector detects signal interruption and turns off Projection Lamp automatically.
Refer to “Power Management” on pages 35 and 36.

NOTE : When “On start” function is ON, this projector is turned

on automatically by connecting AC Power Cord to an
AC outlet. (Refer to pages 35, 36.)

20

KEYSTONE ADJUSTMENT

1

Press KEYSTONE ▲/▼ button on Remote Control Unit or select
Keystone on SETTING menu. (Refer to page 35.) Keystone
dialog box appears.

2

Correct keystone distortion by pressing KEYSTONE ▲/▼ button
or POINT UP/DOWN button(s). Press KEYSTONE ▲ button or
POINT UP button to reduce upper part of image, and press
KEYSTONE ▼ button or POINT DOWN button to reduce lower
part.

Reduce upper width with KEY STONE ▲ button or
POINT UP button.

Reduce lower width with KEY STONE ▼ button or
POINT DOWN button.

If a projected picture has keystone distortion, correct image with KEYSTONE adjustment.

BASIC OPERATION

ADJUSTING SCREEN

Message disappears after 4 seconds.

Message disappears after 4 seconds.

Zoom

Focus

ZOOM ADJUSTMENT

FOCUS ADJUSTMENT

1

Press ZOOM button on Top Control or ZOOM ▲/▼ button on
Remote Control Unit. Message “Zoom” is displayed.

2

Press ZOOM ▲ button or POINT UP button to make image
larger, and press ZOOM

▼ button or POINT DOWN button to

make image smaller.

1

Press FOCUS button on Top Control or FOCUS ▲/▼ button on
Remote Control Unit. Message “Focus” is displayed.

2

Adjust focus of image by pressing FOCUS ▲/▼ button or
POINT UP/DOWN button(s) .

Message disappears after 4 seconds.



Lens shift





LENS SHIFT ADJUSTMENT

1

Press LENS SHIFT button on Top Control or on Remote Control
Unit. Message “Lens shift” is displayed.

2

Press POINT UP button to move image up, press POINT DOWN
button to move image down.

21

BASIC OPERATION

Press FREEZE button on Remote Control Unit to freeze picture on-screen. To cancel FREEZE function, press FREEZE
button again or press any other button except POINT / SELECT / RIGHT CLICK / P-TIMER / LASER button.

Press NO SHOW button on Remote Control Unit to black out image.
To restore to normal, press NO SHOW button again or press any
other button except POINT / SELECT / RIGHT CLICK / P-TIMER /
LASER button.

NO SHOW FUNCTION

PICTURE FREEZE FUNCTION

Message disappears after 4 seconds.

No show

Press P-TIMER button on Remote Control unit. Timer display “00 : 00”
appears on screen and timer starts to count time (00 : 00 ~ 59 : 59).
To stop P-TIMER display, press P-TIMER button. And then, press P­TIMER button again to cancel P-TIMER function.

P-TIMER FUNCTION

1
2

Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
SOUND Menu icon.

Volume

Press VOLUME (+/–) button(s) on Top Control or on Remote Control
Unit to adjust volume. Volume dialog box appears on screen for a few
seconds.
(+) button to increase volume, and (–) button for decreasing.

Mute

Press MUTE button on Remote Control Unit to cut off sound. To
restore sound to its previous level, press MUTE button again or press
Volume (+/–) button(s).

To increase volume, press POINT RIGHT button, and press POINT
LEFT button for decreasing.

Press POINT LEFT/RIGHT button(s) to cut off sound. Dialog box
display is changed to “On” and sound is cut off. To restore sound to
its previous level, press POINT LEFT/RIGHT button(s) again.

Press POINT DOWN button to move a red frame pointer to item
that you want to select, and then press SELECT button.

Indicates roughly
level of volume.

Close SOUND Menu.

SOUND ADJUSTMENT

DIRECT OPERATION

MENU OPERATION

Volume

Mute

Indicates roughly level of
volume.

Press MUTE button to set
Mute function On or Off.

Display disappears after 4 seconds.

SOUND MENU

SOUND Menu icon

22

COMPUTER INPUT

SELECTING INPUT SOURCE

DIRECT OPERATION

Choose Computer by pressing INPUT button on Top Control or on
Remote Control Unit.
If projector cannot reproduce proper image, select correct input source
through MENU OPERATION (see below).

INPUT button

INPUT 1

INPUT 2

INPUT 3

Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.

Press POINT DOWN button and a red-arrow icon will appear.
Move arrow to "RGB", and then press SELECT button.

1

3

When connect a computer output [5 BNC Type (Green, Blue, Red,
Horiz. Sync and Vert. Sync.)] from a computer to G, B, R, H/HV and V
jacks.

WHEN SELECT INPUT 2 (5 BNC INPUT JACKS )

SELECTING COMPUTER SYSTEM

WHEN SELECT INPUT 1 (COMPUTER INPUT TERMINALS )

Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.

Press POINT DOWN button to move a red arrow pointer to Input
1 and then press SELECT button. Source Select Menu will
appear.

1
2

Input 1

INPUT MENU

Move a pointer to either Digital or Analog and then press
SELECT button.

3

When your computer is connected to COMPUTER
INPUT (DIGITAL) terminal, select RGB (Digital).

Digital

When your computer is connected to COMPUTER INPUT
(ANALOG) terminal, select RGB (Analog).

Analog

MENU OPERATION

Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to select Input and press SELECT
button.

Another dialog box INPUT SELECT

Menu will appear.

Press POINT DOWN button and a red-arrow icon will appear.
Move arrow to INPUT source that you want to select, and then
press SELECT button.

1

2

Move a pointer to Digital or
Analog and press SELECT
button.

Move a pointer (red arrow) to
Input 1 and press SELECT
button.

INPUT Menu icon

Source Select Menu

Input 2

INPUT MENU

Move a pointer to RGB and
press SELECT button.

INPUT Menu icon

Move a pointer (red arrow) to
Input 2 and press SELECT
button.

Source Select Menu

INPUT Menu icon

Press POINT DOWN button to move a red arrow pointer to Input
2 and then press SELECT button. Source Select Menu will
appear.

2

23

COMPUTER INPUT

This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to
“COMPATIBLE COMPUTER SPECIFICATION” on page 26). When selecting Computer, this projector automatically tunes
to incoming signal and projects proper image without any special setting. (Some computers need setting manually.)

Note : Projector may display one of following messages.

When projector cannot recognize connected signal as PC
system provided in this projector, Auto PC Adjustment
function operates to adjust projector and message “Auto”
is displayed on SYSTEM Menu icon.
When image is not provided properly, manual adjustment
is required. (Refer to P24 and 25.)

There is no signal input from computer. Make sure
connection of computer and a projector is set correctly.
(Refer to TROUBLESHOOTING on page 40.)

Auto

––––

PC SYSTEM Menu icon
Displays system being
selected.

PC SYSTEM MENU

SELECT COMPUTER SYSTEM MANUALLY

PC SYSTEM Menu icon
Displays system being selected.

Systems on this dialog box can
be selected.

Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to PC
SYSTEM Menu icon.

Press POINT DOWN button to move a red arrow pointer to
system that you want to set, and then press

SELECT button.

1
2

PC SYSTEM MENU

Custom Mode (1~5) set in PC
ADJUST Menu. (P24, 25)

This projector automatically selects PC system among those provided
in this projector and PC system can be also selected manually.

PC ADJUSTMENT

AUTO PC ADJUSTMENT

Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your
computer. Auto PC Adjustment function can be operated as follows.

Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to PC
ADJUST Menu icon.

1
2

Press POINT DOWN button to move a red frame pointer to
AUTO PC Adj. icon and then press SELECT button twice.
This Auto PC Adjustment can be also executed by pressing
AUTO PC ADJ. button on Remote Control Unit.

Move a red frame pointer to AUTO PC
Adj. icon and press SELECT button.

PC ADJUST MENU

Auto PC Adj.

PC ADJUST Menu icon

Store adjustment parameters.
Adjustment parameters from Auto PC Adjustment can be memorized
in this projector. Once parameters are memorized, setting can be
done just by selecting Mode in PC SYSTEM Menu (P23). Refer to
step 3 of MANUAL PC ADJUSTMENT section (P25).

NOTE

● Fine sync, Total dots and Picture Position of some computers can not be fully adjusted with this Auto PC Adjustment
function. When image is not provided properly through this function, manual adjustments are required. (Refer to page 24,

25.)

● Auto PC Adjustment function cannot be operated in Digital Signal input on DVI terminal and “RGB”, “720p (HDTV)”,
“1035i (HDTV)” or “1080i (HDTV)” is selected on PC SYSTEM Menu.

D-VGA, D-SVGA or D-XGA

When digital computer signal is received on DVI terminal,
above message is displayed on PC SYSTEM Menu icon.

AUTOMATIC MULTI-SCAN SYSTEM

24

COMPUTER INPUT

MANUAL PC ADJUSTMENT

This projector can automatically tune to display signals from most personal computers currently distributed. However, some
computers employ special signal formats which are different from standard ones and may not be tuned by Multi-Scan system
of this projector. If this happens, projector cannot reproduce a proper image and image may be recognized as a flickering
picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special
signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This
enables you to recall setting for a specific computer whenever you use it.

Note : This PC ADJUST Menu cannot be operated when in digital signal input on DVI terminal and “RGB” is selected on PC

SYSTEM MENU (P23).

Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to PC
ADJUST Menu icon.

1
2

Press POINT DOWN button to move a red frame pointer to item
that you want to adjust and then press SELECT button.
Adjustment dialog box will appear. Press POINT LEFT/RIGHT
button to adjust value.

Move a red frame icon to item and press
SELECT button.

PC ADJUST MENU

PC ADJUST Menu icon

Adjusts an image as necessary to eliminate flicker from display.
Press POINT LEFT/RIGHT button to adjust value.(From 0 to 31.)

Fine sync

Number of total dots in one horizontal period. Press POINT
LEFT/RIGHT button(s) and adjust number to match your PC image.

Total dots

Adjusts horizontal picture position. Press POINT LEFT/RIGHT
button(s) to adjust position.

Horizontal

Adjusts vertical picture position. Press POINT LEFT/RIGHT
button(s) to adjust position.

Vertical

Press SELECT button to show information of computer selected.

Current mode

Adjusts clamp position. When image has a dark bar(s), try this
adjustment.

Clamp

Press SELECT button at this icon to
adjust “Clamp,” “Display area (H/V)” or
set “Full screen.”

Press POINT LEFT/RIGHT
button to adjust value.

Shows status
(Stored / Free) of
selected Mode.

Selected Mode

Press SELECT button at
Current mode icon to show
information of computer
connected.

Current mode

25

COMPUTER INPUT

NOTE : Display area (H/V) and Full screen cannot be adjusted when

“1035i (HDTV)” or “1080i (HDTV)” is selected on PC
SYSTEM Menu (P23).

Selects area displayed with this projector. Select resolution at
Display area dialog box.

Display area

Adjustment of horizontal area displayed with this projector. Press
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SELECT button.

Display area H

Adjustment of vertical area displayed with this projector. Press
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SELECT button.

Display area V

Press POINT LEFT/RIGHT button(s) to switch Full screen function to
“On” or “Off.” Set “On” to resize image with 4 x 3 aspect ratio to fit
screen.

Full screen

Reset

Store

Closes PC ADJUST MENU.

Quit

Other icons operates as follows.

3

To store adjustment parameters, move a red frame pointer to
Store icon and then press SELECT button. Move a red arrow
pointer to any of Mode 1 to 5 that you want to store and then
press SELECT button.

Reset all adjust parameters on adjustment dialog box to previous
figure.

Mode free

Vacant Mode Shows values of “Total dots,”

“Horizontal,” “Vertical,” “Display

area H,” and “Display area V.”

Store icon

Mode free icon

Close this dialog box.

To store adjustment data.

To clear adjustment data.

To clear adjustment parameters previously set, move a red
frame pointer to Mode free icon and then SELECT button. Move
a red arrow pointer to Mode that you want to clear and then
press SELECT button.

Display area

Press POINT LEFT
/RIGHT button(s) to
adjust value and then
press SELECT button.

Press SELECT button at
Display area icon and Display
area dialog box appears.

This Mode has parameters being stored.

26

COMPUTER INPUT

COMPATIBLE COMPUTER SPECIFICATIONS

Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less
than 160 MHz of Dot Clock.

NOTE : Specifications are subject to change without notice.

ON-SCREEN

DISPLAY

RESOLUTION

H-Freq.

(kHz)

V-Freq.

(Hz)

VGA 1

640 x 480 31.47 59.88
VGA 2 720 x 400 31.47 70.09
VGA 3 640 x 400 31.47 70.09
VGA 4 640 x 480 37.86 74.38
VGA 5 640 x 480 37.86 72.81
VGA 6 640 x 480 37.50 75.00

MAC LC13

640 x 480 34.97 66.60

MAC 13 640 x 480 35.00 66.67

MAC 16 832 x 624 49.72 74.55

MAC 19 1024 x 768 60.24 75.08
MAC 21

1152 x 870

68.68 75.06

SVGA 1 800 x 600

35.156 56.25
SVGA 2 800 x 600 37.88 60.32
SVGA 3 800 x 600 46.875 75.00
SVGA 4 800 x 600 53.674 85.06
SVGA 5 800 x 600 48.08 72.19
SVGA 6 800 x 600 37.90 61.03
SVGA 7 800 x 600 34.50 55.38
SVGA 8 800 x 600 38.00 60.51
SVGA 9 800 x 600 38.60 60.31

SVGA 11 800 x 600 38.00 60.51

ON-SCREEN

DISPLAY

RESOLUTION

H-Freq.

(kHz)

V-Freq.

(Hz)

XGA 11 1024 x 768

XGA 13

1024 x 768

XGA 14 1024 x 768

61.00

XGA15 1024 x 768

46.90 58.20

XGA 8 1024 x 768

47.00 58.30

XGA 9

1024 x 768

(Interlace)

58.03 72.0

SXGA 1 1152 x 864
SXGA 2 1280 x 1024

63.48 79.35

SXGA 3 1280 x 1024

36.00 43.59

SXGA 4

1280 x 1024

64.20 70.40

62.50 58.60

63.90 60.00

63.34 59.98

XGA 1 1024 x 768
XGA 2 1024 x 768
XGA 3 1024 x 768
XGA 4 1024 x 768

48.36 60.00

68.677 84.997

XGA 6 1024 x 768

60.023 75.03

XGA 7 1024 x 768

56.47 70.07

48.50 60.02

44.00 54.58

XGA 5 1024 x 768 60.31 74.92

VGA 7 640 x 480 43.269 85.00

RGB

––––––––
(Interlace)

15.625

25

RGB

––––––––
(Interlace)

15.734 30

SVGA 10 800 x 600 32.70 51.09

ON-SCREEN

DISPLAY

RESOLUTION

H-Freq.

(kHz)

V-Freq.

(Hz)

D-VGA

640 x 480 31.469 59.940

D-SVGA 800 x 600 37.879 60.317

D-XGA

1024 x 768

48.363

60.004

ON-SCREEN

DISPLAY

RESOLUTION

H-Freq.

(kHz)

V-Freq.

(Hz)

When a input signal is digital from DVI terminal, refer to chart below.

XGA 10

1024 x 768 62.04 77.07

SXGA 5 1280 x 1024
SXGA 6 1280 x 1024
SXGA 7

1280 x 1024

SXGA 8 1280 x 1024

63.74 60.01

SXGA 11 1152 x 900

71.69 67.19

81.13 76.107

63.98 60.02

61.20 65.20

720p (HDTV)

––––––––

(Progressive)

45.00 60.00

SXGA 9 1280 x 1024

SXGA 10 1280 x 960

79.976 75.025

60.00 60.00

1080i (HDTV)

––––––––
(Interlace)

33.75 30.00

1035i (HDTV)

––––––––
(Interlace)

33.75 30.00

SXGA 12

1152 x 900

SXGA 13

1280 x 1024

(Interlace)

SXGA 14

1280 x 1024

(Interlace)

71.40 75.60

50.00 43.00

50.00 47.00
SXGA 15 1280 x 1024
SXGA 16 1280 x 1024
SXGA 17 1152 x 900
SXGA 18

1280 x 1024

(Interlace)

63.37 60.01

76.97 72.00

61.85 66.00

46.43 43.35
SXGA 19

1280 x 1024 63.79 60.18

MAC

1280 x 960 75.00 75.08

MAC

1280 x 1024 80.00 75.08

XGA 12

1024 x 768

(Interlace)

35.522 43.48

75.70

27

COMPUTER INPUT

PICTURE IMAGE ADJUSTMENTS

IMAGE LEVEL SELECT (MENU)

Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
IMAGE SELECT Menu icon.

1
2

Press POINT DOWN button to move a red frame pointer to level
that you want to set and then press SELECT button.

Move a red frame icon to level and
press SELECT button.

Level being selected.

IMAGE SELECT MENU

Normal picture level preset on this projector.

Standard

Picture level with improved halftone for graphics.

Real

User preset picture adjustment in IMAGE ADJUST Menu (P28).

IMAGE 1~4

IMAGE SELECT
Menu icon

IMAGE LEVEL SELECT (DIRECT)

Select image level among Standard, Real, Image 1, Image 2, Image 3
and Image 4 by pressing IMAGE button on Top Control or on Remote
Control Unit.

IMAGE button

Standard

Real

Image 1

Image 2

Image 3

Image 4

Normal picture level preset on this projector.

Picture level with improved halftone for graphics.

User preset picture adjustment in IMAGE ADJUST Menu (P28).

Standard

Real

IMAGE 1~4

28

COMPUTER INPUT

Press POINT LEFT/RIGHT buttons
to adjust value.

Reset all adjustment to previous figure.

Reset

Store

Closes IMAGE MENU.

Quit

Other icons operates as follows.

Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
IMAGE ADJUST Menu icon.

1
2

Press POINT DOWN button to move a red frame pointer to item
that you want to adjust and then press SELECT button. Level of
each item is displayed. Adjust each level by pressing POINT
LEFT/RIGHT button(s).

Move a red frame pointer to
item to be selected and then
press SELECT button.

IMAGE ADJUST MENU

IMAGE LEVEL ADJUSTMENT

Press POINT LEFT button to decrease contrast, and POINT RIGHT
button to increase contrast. (From 0 to 63.)

Press POINT LEFT button to adjust image darker, and POINT
RIGHT button to adjust brighter. (From 0 to 63.)

Contrast

Brightness

Press either POINT LEFT button or POINT RIGHT button to obtain
better balance of contrast. (From 0 to 15.)

Gamma

3

To store manually preset image, move a red frame pointer to
Store icon and press SELECT button. Image Level Menu will
appear. Move a red frame pointer to Image 1 to 4 where you
want to set and then press SELECT button.

Image Level Menu
Move a red frame pointer to any
of Image 1 to 4 where you want
to set and then press SELECT
button.

Store icon
Press SELECT button at this icon to
store adjustment.

IMAGE ADJUST
Menu icon

Press POINT LEFT button to lighten red tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)

White balance (Red)

Press POINT LEFT button to lighten green tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)

White balance (Green)

Press POINT LEFT button to lighten blue tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)

White balance (Blue)

Selected Image level

29

COMPUTER INPUT

PICTURE SCREEN ADJUSTMENT

This projector has a picture screen resize function, which enables you to display desirable image size.

Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
SCREEN Menu icon.

When Digital zoom + is selected, ON-SCREEN MENU disappears
and message “D. Zoom +” is displayed. Press SELECT button to
expand image size. And press POINT UP/DOWN/LEFT/RIGHT
button(s) to pan image. Panning function can work only when image
is larger than screen size.
A projected image can be also expanded by pressing D.ZOOM ▲
button on Remote Control Unit.

1

To cancel Digital Zoom +/– mode, press any button except D.ZOOM
▲/▼, SELECT, POINT and AUTO PC ADJ. buttons.

Move red frame to function and press
SELECT button.

Press POINT DOWN button and move a red frame pointer to
function that you want to select and then press SELECT button.

2

Wide

Digital zoom +

NOTE

● True and Digital zoom +/– cannot be operated
when “RGB”, “1035i (HDTV)” or “1080i (HDTV)” is
selected on PC SYSTEM Menu (P23).

● Wide cannot be selected when “720p (HDTV)”,
“1035i (HDTV)” or “1080i (HDTV)” is selected on

PC SYSTEM Menu (P23).

● This projector cannot display any resolution higher
than 1280 X 1024. If your computer’s screen
resolution is higher than 1280 X 1024, reset
resolution to lower before connecting projector.

● Image data in other than XGA (1024 x 768) is
modified to fit screen size in initial mode.

● Panning function may not operate properly if
computer system prepared on PC ADJUST Menu
is used.

Provides image to fit screen size.

Normal

True

SCREEN MENU

SCREEN Menu icon

When Digital zoom – is selected, ON-SCREEN MENU disappears
and message “D. Zoom –” is displayed. Press SELECT button to
compress image size.
A projected image can be also compressed by pressing D.ZOOM

▼

button on Remote Control Unit.

Digital Zoom –

Provides image in its original size. When original image size is larger
than screen size (1024 x 768), this projector enters “Digital zoom +”
mode automatically.

Provides image to fit wide video aspect ratio (16 : 9) by expanding
image width uniformly. This function can be used for providing a
squeezed video signal at 16 : 9.

30

VIDEO INPUT

When video input signal is connected to Y-Pb/Cb­Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.

Y,Pb/Cb,Pr/Cr

SELECTING INPUT SOURCE

Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.

1

Move a pointer to source
and press SELECT button.

Source Select Menu (VIDEO)

Move a pointer to source that you want to select and then press
SELECT button.

3

When video input signal is connected to VIDEO jack,
select Video.

Video

When video input signal is connected to S-VIDEO jack,
select S-Video.

S-Video

When connecting to those equipment, select a type of Video
source in SOURCE SELECT (VIDEO) Menu.

WHEN SELECT INPUT 3 (AV TERMINALS )

WHEN SELECT INPUT 2 (5 BNC INPUT JACKS )

Input 2

INPUT MENU

Move a pointer to Video or
Y, Pb/Cb, Pr/Cr and press
SELECT button.

INPUT Menu icon

Move a pointer (red arrow) to
Input 2 and press SELECT
button.

Source Select Menu

Input 3

INPUT MENU

INPUT Menu icon
Move a pointer (red arrow) to

Input 3 and press SELECT
button.

Press POINT DOWN button to move a red arrow pointer to Input
3 and then press SELECT button. Source Select Menu will
appear.

2

When video input signal is connected to Y-Pb/Cb­Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.

Y,Pb/Cb,Pr/Cr

When video input signal is connected to VIDEO jack,
select Video.

Video

When connecting to those equipment, select a type of Video
source in SOURCE SELECT Menu.

Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.

1

Move a pointer to source that you want to select and then press
SELECT button.

3

Press POINT DOWN button to move a red arrow pointer to Input
2 and then press SELECT button. Source Select Menu will
appear.

2

31

VIDEO INPUT

AV SYSTEM MENU (VIDEO OR S-VIDEO)

AV SYSTEM MENU (COMPONENT VIDEO)

SELECTING VIDEO SYSTEM

Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to AV
SYSTEM Menu icon.

Press POINT DOWN button to move a red arrow pointer to
system that you want to select and then press SELECT button.

1
2

If projector cannot reproduce proper video image, it is necessary to
select a specific broadcast signal format among PAL, SECAM, NTSC,
NTSC 4.43, PAL-M, and PAL-N.

Move pointer to system
and press SELECT
button.

PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N

Projector automatically detects incoming Video signal, and adjusts
itself to optimize its performance.
When Video System is 1035i or 1080i, select system manually first.

If projector cannot reproduce proper video image, it is necessary to
select a specific component video signal format among 480i, 575i,
480p, 575p, 720p, 1035i and 1080i.

Auto

COMPONENT VIDEO SIGNAL FORMAT

VIDEO JACK OR S-VIDEO JACK

Y, Pb/Cb, Pr/Cr JACKS

Projector automatically detects incoming Video system, and adjusts
itself to optimize its performance.
When Video System is PAL-M or PAL-N, select system manually first.

Auto

AV SYSTEM Menu icon
This box indicates system
being selected.

Move pointer to system
and press SELECT
button.

AV SYSTEM Menu icon
This box indicates system
being selected.

32

VIDEO INPUT

PICTURE IMAGE ADJUSTMENTS

IMAGE LEVEL SELECT (MENU)

Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
IMAGE SELECT Menu icon.

1
2

Press POINT DOWN button to move a red frame pointer to level
that you want to set and then press SELECT button.

Move red frame pointer to level
and press SELECT button.

Level being selected.

IMAGE SELECT MENU

Normal picture level preset on this projector.

Standard

Picture level adjusted for picture with fine tone.

Cinema

User preset picture adjustment in IMAGE ADJUST Menu (P34).

IMAGE 1~4

IMAGE SELECT
Menu icon

IMAGE LEVEL SELECT (DIRECT)

Select image level among Standard, Cinema, Image 1, Image 2,
Image 3 and Image 4 by pressing IMAGE button on Top Control or on
Remote Control Unit.

Normal picture level preset on this projector.

Standard

Picture level adjusted for picture with fine tone.

Cinema

User preset picture adjustment in IMAGE ADJUST Menu (P34).

IMAGE 1~4

IMAGE button

Standard

Cinema

Image 1

Image 2

Image 3

Image 4

33

VIDEO INPUT

Press POINT LEFT/RIGHT buttons
to adjust value.

Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
IMAGE ADJUST Menu icon.

1
2

Press POINT DOWN button to move a red frame pointer to item
that you want to adjust and then press SELECT button. Level of
each item is displayed. Adjust each level by pressing POINT
LEFT/RIGHT button(s).

Move a red frame pointer to
item to be selected and then
press SELECT button.

IMAGE ADJUST MENU

IMAGE LEVEL ADJUSTMENT

Press POINT LEFT button to decrease contrast, and POINT RIGHT
button to increase contrast. (From 0 to 63.)

Press POINT LEFT button to adjust image darker, and POINT
RIGHT button to adjust brighter. (From 0 to 63.)

Contrast

Brightness

Press either POINT LEFT button or POINT RIGHT button to obtain
better balance of contrast. (From 0 to 15.)

Gamma

Press SELECT button at this icon to
display other items.

IMAGE ADJUST
Menu icon

Press POINT LEFT/RIGHT buttons
to adjust value.

Press POINT LEFT button to lighten color, and POINT RIGHT button
to deeper color. (From 0 to 63.)

Press POINT LEFT button or POINT RIGHT button to obtain proper
color. (From 0 to 63.)

Color

Tint

Press POINT LEFT button to soften image, and POINT RIGHT
button to sharpen image. (From 0 to 15.)

Sharpness

Press POINT LEFT button to lighten red tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)

White balance (Red)

Press POINT LEFT button to lighten green tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)

White balance (Green)

Press POINT LEFT button to lighten blue tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)

White balance (Blue)

Press SELECT button at this icon to
store value.

Press SELECT button at this icon to
display previous items.

Press POINT LEFT/RIGHT button(s) to change progressive scan
mode. Dialog box display is changed to “Off” and progressive scan
mode to off. Press POINT LEFT/RIGHT button(s) again, progressive
scan mode to on.

Press POINT LEFT/RIGHT button(s) to change noise reduction mode.
Dialog box display is changed to “On to reduce noise (rough parts) of
image. Press POINT LEFT/RIGHT button(s) again, to change noise
reduction mode to off.

Noise reduction

Progressive scan

NOTE :

Tint cannot be adjusted when video system is PAL,
SECAM, PAL-M or PAL-N.

Noise Reduction cannot be operated when video
signal types and systems as follow.

● Composite video signal (SECAM, NTSC4.43,
PAL-M and PAL-N systems).

● S-video signal (SECAM, PAL-M and PAL-N
systems).

● Component video signal.

Progressive cannot be operated when “480p”,
“575p”, “720p”, “1035i” or “1080i” is selected on AV
SYSTEM MENU (P31).

34

VIDEO INPUT

PICTURE SCREEN ADJUSTMENT

This projector has a picture screen resize function, which enables you to display desirable image size.

Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
SCREEN Menu icon.

Press POINT DOWN button and move a red frame pointer to
function that you want to select and then press SELECT button.

1
2

NOTE : SCREEN Menu cannot be operated when

“720p,” “1035i,” or “1080i” is selected on AV
SYSTEM Menu (P31).

Move red frame to function and press
SELECT button.

SCREEN MENU

SCREEN Menu icon

Provides image at a wide screen ratio of 16 : 9.

Wide

Provides image at a normal video aspect ratio of 4 : 3.

Normal

3

To store adjustment data, move a red frame pointer to Store icon
and press SELECT button. Image Level Menu will appear.
Move a red frame pointer to Image Level 1 to 4 and then press
SELECT button.

Image Level Menu
Move a red frame pointer to
image icon to be set and
then press SELECT button.

Store icon

Reset all adjustment to previous figure.

Reset

Store

Closes IMAGE MENU.

Quit

Other icons operates as follows.

35

SETTING

Ceiling

When this function is “On,” picture is top / bottom and left / right
reversed. This function is used to project image from a ceiling
mounted projector.

Rear

When this function is “On,” picture is left / right reversed. This
function is used to project image to a rear projection screen.

Ceiling function

Rear function

Keystone

When image is distorted vertically, select Keystone. ON-SCREEN
MENU disappears and Keystone dialog box is displayed. Correct
keystone distortion by pressing POINT UP/DOWN button(s). Refer
to KEYSTONE ADJUSTMENT on page 20.

SETTING MENU

Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red-frame pointer to
SETTING icon.

1
2

Language

Language used in ON-SCREEN MENU is selectable from among
English, German, French, Italian, Spanish, Portuguese, Dutch,
Swedish, Chinese, Korean and Japanese.

Display

This function decides whether to display On-Screen Displays.

On ··· shows all On-Screen Displays.
Off ···· sets On-Screen Displays disappeared except;

● ON-SCREEN MENU

● “Power off?” message

Set a red frame
pointer to item and
press SELECT
button.

Press POINT DOWN button to move a red-frame pointer to item
that you want to set and then press

SELECT button. Setting

dialog box appears.

Blue back

When this function is “On,” this projector will produce a blue image
instead of video noise on screen when any input source is unplugged
or turned off.

Logo

When this function is “On,” projector displays our logo when starting
up.

When pressing SELECT
button at Language,
Language Menu appears.

Move a pointer to item and
then press POINT
LEFT/RIGHT button(s).

SETTING MENU

SETTING Menu icon

36

SETTING

This function turns Projection Lamp off when this projector detects
signal interruption and is not used for a certain period in order to
reduce power consumption and maintain Lamp-life. (This projector is
shipped with this function ON.)

Power Management function operates to turn Projection Lamp off
when input signal is interrupted and any button is not pressed over 5
minutes. This function operates as follows;

1. When any input signal is interrupted, “No signal” and counting
down display appears (for 5 minutes).

2. After counting down for 5 minutes, projector lamp and READY
indicator are turned off.

3. When READY indicator flashing, Projection Lamp can be
turned on again (Power Management mode).
In this Power Management mode, Projection Lamp is
automatically turned on when input signal connected or
projector is operated with any button on Top Control or on
Remote Control Unit again.

Power management

This function is used to reset Lamp Replace Counter. When
replacing Projection Lamp, reset Lamp Replace Counter by using
this function. Refer to page 39 for operation.

Lamp counter reset

Remote control

This projector has two different remote control codes; factory-set
normal code (Code 1) and secondary code (Code 2). This switching
function prevents remote control operation mixture (jam) when
operating several projectors or video equipment together.
When operating projector in “Code 2,” both projector and Remote
Control Unit must be switched to “Code 2.”

To change code of Projector;

Set Remote control in SETTING MENU to “Code 2.”

To change code of Remote Control Unit;

Press both MENU and IMAGE buttons on Remote Control Unit
together for over 10 seconds.

After changing code, make sure Remote Control operates properly.
To return to normal code (Code 1), operate both projector and
Remote Control in ways above again.

NOTE : When batteries of Remote Control Unit are replaced or ALL-

OFF switch is turned to “ALL-OFF,” remote transmit code
automatically returns to normal code (Code 1).

On start

When this function is “On,” projector is automatically turned on just
by connecting AC Power cord to a wall outlet.

Note ; Be sure to turn projector off properly (refer to section

“TURNING OFF PROJECTOR” on P19). If projector is turned
off in wrong steps, On Start function does not operate
properly.

Time left until Lamp off.

Move pointer to item and then press
POINT LEFT/RIGHT button(s).

Move pointer to Lamp counter reset and then press
SELECT button. Message “Lamp replace counter
reset?” is displayed.

Press SELECT button at this icon to
display other items.

Press SELECT button at this icon to
display previous items.

On start

37

SETTING/APPENDIX

OPERATING WIRELESS MOUSE

INSTALLATION

Wireless Remote Control Unit is not only able to operate this projector but also usable as a wireless mouse for most
Personal Computers. POINT buttons and two CLICK buttons are used for wireless mouse operation.
This Wireless Mouse function is available only when PC mouse pointer is displayed on a projected screen. When ON­SCREEN MENU or any message / dialog box is displayed on screen instead of PC mouse pointer, this Wireless Mouse
function cannot be used.

Connect mouse port (or USB port) of your computer to Control
Port (or USB connector) of this projector with Control Cable (or
USB cable). (Refer to page 11, 12 for connection.)

Turn a projector on first, and then turn on your computer. When
computer is switched on first, Wireless Mouse may not work
properly.

1
2

To use Wireless Remote Control Unit as Wireless Mouse for a Personal Computer, installation of mouse driver (not supplied)
is required. Make sure that mouse driver is properly installed in your computer. And make sure that mouse port (or USB
port) of a Personal Computer is activated.

OPERATING WIRELESS MOUSE

When controlling a PC mouse pointer, operate Wireless Mouse with POINT button, SELECT button, and RIGHT CLICK
button on Wireless Remote Control Unit.

Used to move PC mouse pointer. Pointer is moved corresponding
with direction you are pressing.

POINT button

This button has same function as left button in a PC mouse.

SELECT (LEFT CLICK) button

This button has same function as right button in a PC mouse. This
button is not available for controlling this projector.

RIGHT CLICK button

Note : When your computer has no mouse

port, connect Serial Port of your
computer to Control Port of a projector
with Control Cable for Serial Port (not
supplied).

POINT button (Move pointer)

SELECT button
(left button of mouse)

RIGHT CLICK button
(right button of mouse)

USB

Projector mode

Select " " when controlling a projector with computer.
NOTE: Before you control a projector by computer, install USB driver

(optionally sold parts) and set up computer following instruc­tion in USB driver package. Contact your authorized dealer.

This Projector is equipped with USB port for interactive operation
between a projector and computer. Set mode following steps below.

Wireless Mouse mode

Select " " when controlling a computer with Remote Control of
this projector.

Closes SETTING MENU.

Quit

Move pointer to item and then press
POINT LEFT/RIGHT button(s).

Press SELECT button at this icon to
display previous items.

USB

38

APPENDIX

CLEANING PROJECTION LENS

Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch a surface.

When a projector is not in use, replace Lens Cover.

1

3

Lightly wipe a cleaning cloth over Projection Lens.

2

Follow these steps to clean Projection Lens:

MAINTENANCE

WARNING TEMP. INDICATOR

WARNING TEMP. Indicator flashes red when an internal temperature of a projector exceeds normal temperature. This
Indicator stops flashing when temperature of a projector returns to normal.
When WARNING TEMP. Indicator continues to flash, check items listed below.

Ventilation Slots of a projector may be blocked. In such an event, reposition a projector so that Ventilation Slots are
not obstructed.

AIR FILTER CARE AND CLEANING

Air Filter may be clogged with dust particles. Clean Air Filter by following section AIR FILTER CARE AND CLEANING
below.

1
2

If WARNING TEMP. Indicator remains on after performing above checks, Cooling Fans or Internal Circuits may be
malfunctioning. Contact service personnel from an authorized dealer or a service station.

3

AIR FILTER
Pull up and remove.

Turn off a projector, and disconnect AC power cord from AC
outlet.

Turn a projector upside down and remove Air Filter (2 used) by
pulling latches upward.

1
2

Air Filter prevents dust from accumulating on surface of Projection Lens and Projection Mirror. Should Air Filter become
clogged with dust particles, it will reduce Cooling Fans’ effectiveness and may result in internal heat build up and adversely
affect life of a projector. Clean Air Filter following steps below:

Clean Air Filter with a brush or wash out dust and particles.

3

Replace Air Filter properly. Make sure that Air Filter is fully
inserted.

4

CAUTION

Do not operate a projector with Air Filter removed. Dust
may accumulate on LCD Panel and Projection Mirror
degrading picture quality.
Do not put small parts into Air Intake Vents. It may result
in malfunction of a projector.

RECOMMENDATION

We recommend avoiding dusty/smoky environments when operating a projector. Usage in these environments
may cause poor image quality.

When using under dusty or smoky conditions, dust may accumulate on a lens, liquid crystal panels, or optical elements
inside a projector. This condition may degrade quality of a projected image.
When above symptoms are noticed, contact your authorized dealer or service station for proper cleaning.

39

APPENDIX

LAMP REPLACEMENT

When life of Projection Lamp of this projector draws to an end, LAMP REPLACEMENT indicator lights yellow. When a
projected image becomes dark or color of an image becomes unnatural, replacement of Projection Lamp is required.

Turn off a projector and disconnect AC plug. Allow a projector to
cool for at least 45 minutes.

Loosen 2 screws with a screwdriver and pull out Lamp Assembly
by grasping Handle.

1

3

Replace Lamp Assembly with a new one and tighten 2 screws
back. Make sure that Lamp Assembly is set properly. Replace
Lamp Cover and tighten 2 screws.

4

Remove 2 screws with a screwdriver and open Lamp Cover.

2

Connect AC Power Cord to a projector and turn it on.

6

Follow these steps to replace lamp assembly.

Reset Lamp Replace Counter (refer to section “Lamp Replace
Counter” below).

5

LAMP
ASSEMBLY

HANDLE

LAMP COVER

NOTE : Do not reset Lamp Replace Counter when Projection

Lamp is not replaced.

ORDER REPLACEMENT LAMP

Replacement Lamp can be ordered through your dealer. When ordering Projection Lamp, give following
information to dealer.

● Model No. of your projector : PLC-XP40L/PLC-XP45L

● Replacement Lamp Type No. : POA-LMP38

(Service Parts No. 610 293 5868)

LAMP REPLACE COUNTER

Be sure to reset Lamp Replace Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP
REPLACE Indicator stops lighting.

Turn projector on, press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to
move a red frame pointer to SETTING Menu icon (refer to page 35, 36).

1

Press POINT DOWN button to move a red frame pointer to “Lamp counter reset” and then press

SELECT button.

Message "Lamp replace counter reset?" is displayed. Move pointer to [Yes] and then press SELECT button.

2

Do not reset Lamp Replace Counter except after Projection Lamp is replaced.

Another confirmation dialog box appears and select [Yes] to reset Lamp Replace Counter.

3

CAUTION

Do not drop a lamp assembly or touch a glass
bulb! Glass can shatter and may cause injury.

CAUTION

For continued safety, replace with a lamp
assembly of same type.
Allow a projector to cool for at least 45
minutes before you open Lamp Cover. Inside
of a projector can become very hot.

40

APPENDIX

TROUBLESHOOTING

Before calling your dealer or service center for assistance, check matters below once again.

1. Make sure you have connected a projector to your computer or video equipment as described in section "CONNECTING
PROJECTOR" on pages 11 ~ 13.

2. Check cable connection. Verify that all computer, video and power cord are properly connected.

3. Verify that all power is switched on.

4. If a projector still does not produce an image, re-start your computer.

5. If an image still does not appear, unplug a projector from your computer and check your computer monitor's display.
Problem may be with your graphics controller rather than with a projector. (When you reconnect a projector, be sure to
turn computer and monitor off before you power up a projector. Power equipment back on in order of : Projector and
computer.)

6. If problem still exists, check following chart.

No power.

● Plug a projector into your AC outlet.

● Make sure READY Indicator lights.

● Wait 90 seconds after a projector is turned OFF when turning a projector back on.

NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as

follows:

1. LAMP indicator lights bright and READY indicator turns off.

2. After 90 seconds, READY indicator lights green again and a projector may be
turned on by pressing Power ON-OFF button.

● Check WARNING TEMP. indicator. If indicator flashes red, a projector cannot be turned
on.
(See "TURNING ON/OFF PROJECTOR" section on page 19.)

● Check Projection Lamp. (Refer to page 39.)

Image is out of
focus.

● Adjust focus of a projector.

● Make sure a projection screen is at least 4.6’ (1.4m) from a projector.

● Check Projection Lens to see if it needs cleaning.

NOTE : Moving a projector from a cool temperature location to a warm temperature location

may result in moisture condensation on Projection Lens. In such an event, leave a
projector OFF and wait until condensation disappears.

Picture is Left/Right
reversed.

● Check Ceiling / Rear feature. (See “SETTING” section on page 35.)

Problem: Try these Solutions

Picture is
Top/Bottom
reversed.

● Check Ceiling feature. (See “SETTING” section on page 35.)

Some displays are
not seen during
Operation.

● Check Display feature.(See “SETTING” section on page 35.)

No image.

● Check connection between your computer or video equipment and a projector.

● When turning a projector on, it takes about 30 seconds to display an image.

● Check system that you select is corresponding with your computer or video equipment.

● Make sure temperature is not out of Operating Temperature (5°C ~ 35°C).

No sound.

● Check audio cable connection from audio input source.

● Adjust audio source.

● Press VOLUME (+) button.

● Press MUTE button.

41

APPENDIX

Remote Control Unit
does not work.

● Check batteries.

● Check ALL-OFF switch on Remote Control Unit is set to “ON.”.

● Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.

● Make sure you are not too far from a projector when using Remote Control Unit.

Maximum operating range is 16.4’ (5m).

Problem: Try these Solutions

Wireless Mouse
function does not
work.

● Check cable connection between a projector and your computer.

● Check mouse setting on your computer.

● Turn a projector on before turning on a computer.

SERVICE

WARNING: High voltages are used to operate this projector. Do not attempt to open cabinet.

You can often correct operating problems yourself. If a projector fails to work properly, see "TROUBLESHOOT­ING" section on page 40, 41. To correct failure, try "Solutions".

If after following all operating instructions, you find that service is necessary, contact Sanyo Service Station or
store where you purchased unit.
Give model number and explain difficulty. We will advise you how to obtain service.

This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety
standards against risk of fire, casualty and electrical hazards.

The CE Mark is a Directive conformity mark of the European Community (EC).

Multi-media Projector

42

APPENDIX

Accessories

● Specifications are subject to change without notice.

TECHNICAL SPECIFICATIONS

1.3" TFT Active Matrix type, 3 panels

15.7 lbs (7.1 kg)

12.6" x 6.6" x 16.8" (319 mm x 168 mm x 429.5 mm)

1024 x 768 dots
2,359,296 (1024 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N

Up and Down
800 TV lines (HDTV)

INT. SP. Stereo (R and L), 2 watt RMS (T.H.D. 10%)

41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)

Owner’s Manual
AC Power Cord
Wireless/Wired Remote Control Transmitter and Batteries
Remote Control Cable
VGA Cable
MAC/VGA Adapter
3 Types Control Cable (For PS/2, Serial and ADB port)
Protective Dust Cover

Projector Type

Net Weight

Dimensions

(W x H x D)

Panel Resolution
Number of Pixels
Color System

Scanning Frequency

Horizontal Resolution

Built-in Speakers

Operating Temperature
Storage Temperature

LCD Panel System

200 watt type

Projection Lamp

0˚ to 10.5˚

Feet Adjustment

Power Source : AA, UM3 or R06 Type x 2
Operating Range : 16.4’ (5m) / ±30˚
Dimensions : 2.2” x 1.3” x 7.6” (55mm x 34mm x 192mm)
Net Weight : 0.36 lbs (165 g) (including batteries)
Laser Pointer : Class II Laser

(Max. Output : 1mW / Wave length : 650±20nm)

Remote Control Transmitter

480i, 480p, 575i, 575p, 720p, 1035i and 1080i

High Definition TV Signal

AC 100 ~ 120 V (3.6 A Max. Ampere), 50 / 60 Hz

(The U.S.A and Canada)

AC 200 ~ 240 V (1.8 A Max. Ampere), 50 / 60 Hz

(Continental Europe and The U.K.)

Voltage and
Power Consumption

H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz

Motorized Lens Shift

DVI Terminal (Digital), HDB 15-pin Terminal (Analog)
and Stereo Mini Type Jack (Audio)

Input 1 Jacks

BNC Type x 5 (G or VIDEO/Y, B or Cb/Pb, R or Cr/Pr, H and V), Stereo Mini
Type Jack (Audio)

Input 2 Jacks

RCA Type x 3 (VIDEO/Y, Cb/Pb and Cr/Pr), RCA Type x 2 (Audio R and L)
and DIN 4-pin (S-Video)

Input 3 Jacks

DIN 8-pin (Control port), USB port (Series B receptacle) and Wired Remote Jack

Other Jacks

43

APPENDIX

CONFIGURATIONS OF TERMINALS

COMPUTER INPUT-1 TERMINAL (ANALOG)

Terminal : HDB15-PIN

Connect display output terminal of computer to this terminal with VGA Cable (supplied). When connecting Macintosh
computer, MAC Adapter (not supplied) is required.

Red Input

Ground (Horiz.sync.)

Green Input

Sense 2

Blue Input

Ground (Red)
Ground (Green)
Ground (Blue)

1

5

2

4

3

6
7
8

+5V Power

Horiz. sync.

Ground (Vert.sync.)

DDC Data

Sense 0

Vert. sync.
DDC Clock

9

13

10

12

11

14
15

Pin Configuration

Terminal : Mini DIN 8-PIN

Connect control port (PS/2, Serial or ADB port) on your computer to this connector with Control Cable (supplied).

Pin Configuration

CONTROL PORT CONNECTOR

-----

CLK

DATA

GND

-----

-----

GND

-----

R X D

-----

-----

GND

RTS / CTS

T X D

GND
GND

-----

ADB

-----

GND

-----

-----

-----

GND

PS/2 Serial

ADB
1
2
3
4
5
6
7
8

COMPUTER INPUT-1 TERMINAL (DIGITAL)

Terminal : DVI 24-pin

Connect display output terminal of computer to this terminal with DVI cable (for Single Link T.M.D.S. / not supplied).

T.M.D.S. Data2–

No Connect

T.M.D.S. Data2+

No Connect

T.M.D.S. Data2 Shield

DDC Clock
DDC Data
No Connect

1

5

2

4

3

6
7
8

Pin Configuration

T.M.D.S. Data1–

No Connect

T.M.D.S. Data1+

No Connect

T.M.D.S. Data1 Shield

+5V Power
Ground (for +5V)
Hot Plug Detect

9

13

10

12

11

14
15
16

T.M.D.S. Data0–

No Connect

T.M.D.S. Data0+

No Connect

T.M.D.S. Data0 Shield

T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock–

17

21

18

20

19

22
23
24

Vcc

- Data

+ Data

Ground

1
2
3
4

USB CONNECTOR (Series B)

Pin Configuration

Connect USB port terminal on your computer or peripheral equipment to this connector with USB Cable (not supplied).

5

34

10

9 678

15

14

13

2

1

12

11

1

2

3

4

5

6

9

10

11

12

13

14

17

18

19

20

21

22

7

8

15

16

23

24

8 7 6

3

5

4

1

2

2

1

34

Printed in Japan
Part No. 610 298 6082 (1AA6P1P3218-- MA8AL)

SANYO Electric Co., Ltd