Sanyo PLC-XF46N-E User Manual

Download

Page 1

Owner's Manual

PLC-XF46N/E

Multimedia Projector

MODEL

✽ Projection lens is optional.

Page 2

CAUTION : TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE OWNER’S MANUAL WITH THIS UNIT.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Before operating this projector, read this manual thoroughly and operate the projector properly.

This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintain it in better condition for a considerable time.

Improper operation may result in not only shortening the product life, but also malfunctions, fire hazard, or other accidents.

If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the “Troubleshooting” section in the end of this booklet. If the problem still persists, contact the dealer where you purchased the projector or the service center.

Safety Precaution

WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

– This projector produces intense light from the projection

lens. Do not stare directly into the lens as much as possible. Eye damage could result. Be especially careful that children do not stare directly into the beam.

– Install the projector in a proper position. If not, it may result

in a fire hazard.

– Provide appropriate space on the top, sides and rear of the

projector cabinet for allowing air circulation and cooling the projector. Minimum clearances must be maintained. If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. Do not cover the ventilation slot on the projector. Heat build-up can reduce the service life of your projector, and can also be dangerous.

– If the projector is not to be used for an extended time,

unplug the projector from the power outlet.

NOTE: This symbol mark and recycle system are applied only

to EU countries and not applied to the countries in the other area of the world.

Your SANYO product is designed and manufactured with high quality materials and components which can be recycled and reused.

This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste.

Please dispose of this equipment at your local community waste collection/recycling centre. In the European Union there are separate collection systems for used electrical and electronic products.

Please help us to conserve the environment we live in!

CAUTION ON HANGING FROM THE CEILING

When hanging the projector from the ceiling, clean the air intake vents, air filters, and top of the projector periodically with a vacuum cleaner. If you leave the projector without cleaning for a long time, the dust will block the operation of the cooling function, and it may cause a breakdown or a disaster.

DO NOT SET THE PROJECTOR IN GREASY, WET, OR SMOKY CONDITIONS SUCH AS IN A KITCHEN TO PREVENT A BREAKDOWN OR A DISASTER. IF THE PROJECTOR COMES IN CONTACT WITH OIL OR CHEMICALS, IT MAY BECOME DETERIORATED.

READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.

SIDE and TOP

REAR

TO THE OWNER

3.3' (1m)

Page 3

SAFETY INSTRUCTIONS

All the safety and operating instructions should be read before the product is operated.

Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

Follow all warnings and instructions marked on the projector.

For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges.

Do not expose this unit to rain or use near water... for example, in a wet basement, near a swimming pool, etc...

Do not use attachments not recommended by the manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers.

An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.

The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.

This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided.

Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector.

This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.

Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by persons walking on it.

Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally by following the

operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.

e. If the projector has been dropped or the cabinet has been

damaged.

f. When the projector exhibits a distinct change in

performance-this indicates a need for service.

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.

Voor de klanten in Nederland

Bij dit product zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA.

CAUTION

Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75.

Ne peut être utilisé dans une salle d’ordinateurs telle que définie dans la norme ANSI/NFPA 75 Standard for Protection of Electronic Computer/Data Processing Equipment.

Page 4

COMPLIANCES

AC Power Cord for the United Kingdom :

This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus . If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions. If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed. The end of the flexible cord should be suitably prepared and the correct plug fitted. (See Over)

WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET OUTLET.

The Wires in this mains lead are coloured in accordance with the following code:

Green-and-yellow ············ Earth Blue ································· Neutral

Brown ······························ Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

WARNING : THIS APPARATUS MUST BE EARTHED.

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada :

AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA). AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable to insert the plug into the outlet, contact your electrician.

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

AC POWER CORD REQUIREMENT

Federal Communication Commission Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

CAUTION!

This is a Class A equipment. This equipment can cause interference in residential areas; in this case, the operator can be asked to take adequate countermeasures.

GROUND

ASA

Page 5

FEATURES AND DESIGN 6

BEFORE OPERATION 17

COMPUTER INPUT 26

VIDEO INPUT 34

SETTING 39

APPENDIX 42

PREPARATION 7

NAME OF EACH PART OF PROJECTOR 7 SETTING-UP PROJECTOR 8

CONNECTING AC POWER CORD 8 LENS INSTALLATION 9 POSITIONING PROJECTOR 9 LENS SHIFT ADJUSTMENT 9 PICTURE LEVEL AND TILT ADJUSTMENT 10 INSTALLING PROJECTOR IN PROPER POSITION 10 MOVING PROJECTOR 11

CONNECTING PROJECTOR 12

TERMINALS OF PROJECTOR 12 CONNECTING TO COMPUTER 15 CONNECTING TO VIDEO EQUIPMENT 16

SIDE CONTROLS AND INDICATORS 17 OPERATION OF REMOTE CONTROL 19

REMOTE CONTROL BATTERIES INSTALLATION 20

OPERATING ON-SCREEN MENU 21

HOW TO OPERATE ON-SCREEN MENU 21 FLOW OF ON-SCREEN MENU OPERATION 21 MENU BAR 22

SELECTING INPUT SOURCE 26 SELECTING COMPUTER SYSTEM 26 PC ADJUSTMENT 28

AUTO PC ADJUSTMENT 28 MANUAL PC ADJUSTMENT 29

PICTURE IMAGE ADJUSTMENT 31

IMAGE LEVEL SELECT 31 IMAGE LEVEL ADJUSTMENT 32

PICTURE SCREEN ADJUSTMENT 33

SELECTING INPUT SOURCE 34 SELECTING VIDEO SYSTEM 35 PICTURE IMAGE ADJUSTMENT 36

IMAGE LEVEL SELECT 36 IMAGE LEVEL ADJUSTMENT 37

PICTURE SCREEN ADJUSTMENT 38

SETTING MENU 39

MAINTENANCE 42

WARNING TEMP. INDICATOR 42 AIR FILTER CARE AND CLEANING 42 LAMP MANAGEMENT 43 LAMP REPLACEMENT 44 LAMP REPLACE COUNTER 45

TROUBLESHOOTING 47

MENU TREE 48 INDICATORS AND PROJECTOR CONDITION 50 COMPATIBLE COMPUTER SPECIFICATIONS 51

TECHNICAL SPECIFICATIONS 53

CONFIGURATIONS OF TERMINALS 54 DIMENSIONS 55

BASIC OPERATION 23

TURNING ON / OFF PROJECTOR 23

TURNING ON PROJECTOR 23 TURNING OFF PROJECTOR 23

ADJUSTING SCREEN 24

ZOOM ADJUSTMENT 24 FOCUS ADJUSTMENT 24 LENS SHIFT ADJUSTMENT 24 KEYSTONE ADJUSTMENT 24 PICTURE FREEZE FUNCTION 25 NO SHOW FUNCTION 25 P-TIMER FUNCTION 25

TRADEMARKS

● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.

● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.

● Windows and PowerPoint are registered trademarks of Microsoft Corporation.

● Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its

respective corporation.

Page 6

FEATURES AND DESIGN

This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology.

◆ Compatibility

This projector widely accepts various video and computer input signals including;

● Computers

IBM-compatible or Macintosh computer up to 1600 x 1200 resolution.

● 6 Color Systems

NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PALN color system can be connected.

● Component Video

Component video signal, such as a DVD player output high definition TV signals including 480i, 480p, 575i, 575p, 720p, 1035i, 1080i-50 or 1080i60, can be connected.

● S-Video

S-Video signal, such as a S-VHS VCR output signal, can be connected.

◆ High Resolution Image

◆ Multi-Scan System

This projector has Multi-Scan System to conform to almost all computer output signals quickly. There is no need for troublesome manual adjustment of frequency and other settings.

◆ Keystone Correction

Positioning height of a projector may result in distorted image being displayed in a trapezoid shape. Keystone Correction solves this problem by digitally altering projection to produce undistorted images.

◆ Multilanguage Menu Display

Operation menu is displayed in; English, German, French, Italian, Spanish, Portuguese, Dutch, Swedish, Russian, Chinese, Korean or Japanese.

◆ One-Touch Auto PC Adjustment

Incoming computer video signals are recognized and best adjustment is automatically set by Auto PC Adjustment. No complicated setup is necessary and projection is always precise.

◆ Digital Zoom (for Computer)

Digital Zoom function adjusts image size to approx. 1/4 ~ 49 times of original image size, allowing you to focus on crucial information at a presentation.

◆ Power Management

Power Management function is provided to reduce power consumption while a projector is not in use. This Power Management function operates to turn Projection Lamp off when a projector detects signal interruption and any button is not pressed over 5 minutes. Projection Lamp is automatically turned on again when a projector detects signal or any operation button is pressed. This projector is shipped with this function ON.

◆ Digital Visual Interface

This projector is equipped with DVI 29-pin terminal for connecting DVI output from a computer.

◆ Progressive Scan Function

This function converts interlace video signals into progressive scan signals and provide fine picture quality.

◆ Motor-driven Lens Shift

Projection lens can be moved up, down left and right with motor-driven lens shift function. This function makes it easy to provide projected image where you want. Zoom and focus can be also adjusted with motor-driven operation.

◆ Multi Versatile Platform

This projector applies various input/output terminals and 4 terminal slots for expansion to tune to diversity of signals from computers and video equipment.

4-built-in Terminal Slots enable you to arrange any combinations of input sources just by changing Terminal Boards. For Terminal Boards, contact sales dealer where you purchased a projector.

◆ Selectable Terminal Slots

◆ Network board (Optional)

Network board is an optional product to control and set up a projector via the network cable by accessing to the connected projector using the web browser on your computer. It can be controlled and set up the projector remotely. Contact the sales dealer where you purchased this projector for optional parts.

This projector provides 1024 x 768 dots resolution for computer input and 800 horizontal TV lines. Resolution from a computer between XGA (1024 x 768) and UXGA (1600 x 1200) is compressed into 1024 x 768 dots. This projector cannot display image of over 1600 x 1200 dots. When resolution of your computer is over than 1600 x 1200, reset a computer output for lower resolution.

Page 7

PREPARATION

NAME OF EACH PART OF PROJECTOR

BOTTOM OF CABINET

BACK OF CABINET

HOT AIR EXHAUSTED !

Air blown from exhaust vent is hot. When using or installing a projector, following precautions should be taken.

● Do not put a flammable object near this vent.

● Keep rear grills at least 3.3’ (1m) away from

any object, especially heat-sensitive object.

● Do not touch this area, especially screws and metallic parts. This area will become hot while a projector is used.

This projector detects internal temperature and automatically controls operating power of Cooling Fans.

FRONT OF CABINET

LAMP COVER

ADJUSTABLE FEET

This projector is equipped with cooling fans for protection from overheating. Pay attention to following to ensure proper ventilation and avoid a possible risk of fire and malfunction.

● Do not cover vent slots.

● Keep bottom clear of any objects.

Obstructions may block cooling air.

AIR INTAKE VENTS

PROJECTION LENS

INFRARED

REMOTE RECEIVER

LENS CAP

POWER CORD

CONNECTOR

EXHAUST VENT

MAIN ON / OFF

SWITCH

INFRARED

REMOTE RECEIVER

CARRYING HANDLE

LEVEL AND TILT ADJUST HANDLE

AIR FILTER

ADJUSTABLE FEET

Do not turn on a projector with lens cap attached. High temperature from light beam may damage lens cap and result in fire hazard.

CAUTION

Page 8

PREPARATION

SETTING-UP PROJECTOR

This projector uses nominal input voltages of 120 V or 200-240 V AC. This projector automatically selects correct input voltage. It is designed to work with singlephase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system. Consult your authorized dealer or service station if you are not sure of type of power supply being in use. Connect a projector with peripheral equipment before turning a projector on. (Refer to pages 13 ~ 16 for connection.)

CONNECTING AC POWER CORD

Connect AC Power Cord (supplied) to a projector. AC outlet must be near this equipment and must be easily accessible.

To POWER CORD CONNECTOR on a projector.

Projector side AC Outlet side

Ground

NOTE ON POWER CORD

AC Power Cord must meet requirement of country where you use a projector. Confirm AC plug type with chart below and proper AC power cord must be used. If supplied AC Power Cord does not match AC outlet, contact your sales dealer.

To the AC Outlet.

(120 V AC)

For Continental Europe

For the U.S.A. and Canada

For the U.K.

To the AC Outlet.

(200 - 240 V AC)

To the AC Outlet.

(200 - 240 V AC)

Page 9

PREPARATION

POSITIONING PROJECTOR

Before setting up a projector, install Projection Lens on a Projector.

1. Before installation, check where a projector is used and prepare suitable lens. For specifications of Projection Lens, refer to manual separately attached or contact sales dealer where you purchased a projector.

2. For installation, refer to installation manual supplied to a Projector.

LENS INSTALLATION

When moving or setting up a projector, be sure to replace a Lens Cap to protect a surface. And be careful not to hold or subject a lens to strong forces. It may damage lens, cabinet, or mechanical parts.

Projection lens can be moved up, down, left and right with motor-driven lens shift function. This function makes it easy to provide projected image where you want.

LENS SHIFT ADJUSTMENT

MOVED UP OR DOWN

MOVED LEFT OR RIGHT

Use LENS SHIFT button and POINT UP/DOWN button to move image up or down. (Refer to page 24.)

Use LENS SHIFT button and POINT LEFT/RIGHT button to move image left or right. (Refer to page 24.)

This projector is designed to project on a flat projection surface.

ROOM LIGHT

Brightness in room has a great influence on picture quality. It is recommended to limit ambient lighting in order to provide best image.

This projector is equipped with cooling fan to protect it from overheating. Pay attention to following to ensure proper ventilation and avoid a possible risk of fire and malfunction.

● Do not cover vents with papers or other materials.

●

Keep rear grill at least 3.3 feet (1 m) away from any object.

● Make sure that there are no objects under a projector. An object under a projector may prevent a projector from taking cooling air through bottom vent.

VENTILATION

AIR INTAKE VENT (BOTTOM SIDE)

EXHAUST VENT (REAR SIDE)

SCREEN

Page 10

PREPARATION

PICTURE LEVEL AND TILT ADJUSTMENT

Picture tilt and projection angle can be adjusted with handles on both sides of a projector. Projection angle can be adjusted to 5.7 degrees upper way.

LEVEL AND TILT ADJUST HANDLE

ADJUSTABLE FEET

Height of front feet can be adjusted by turning handles.

KNOB

Press knob on handle. Handle pop out.

Turn handles (right and left) until picture is projected on proper position. Adjust height of rear adjustable feet by rotating them until projector properly stabled on table.

Press knob and retract handle.

REAR ADJUSTABLE FEET. (Refer to P7).

INSTALLING PROJECTOR IN PROPER POSITION

Install the projector properly. Improper installation may reduce the lamp lifetime and cause a fire hazard.

Do not tilt the projector more than 10 degrees above and below.

Do not point the projector up to project an image.

Do not point the projector down to project an image.

Do not put the projector on either side to project an image.

NO UPWARD

NO DOWNWARD

NO SIDEWAYS

10˚

Page 11

MOVING PROJECTOR

CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR

● Do not drop or bump a projector, otherwise damages or malfunctions may result.

● When carrying a projector, use a suitable carrying case.

● Do not transport a projector by using a courier or transport service in an unsuitable transport case. This

may cause damage to a projector. To transport a projector through a courier or transport service, consult your dealer and best case should be applied.

For safety, be sure to hold Carrying Handles on both sides by 2 or more people when moving a projector. Moving it unproperly may result in damage of cabinet or person's injury. Replace lens cap and retract feet to prevent damage to lens and cabinet.

Pull up lock buttons on each side of carrying handles and release locks.

CARRYING HANDLE

LOCK BUTTONS

Pull carrying handles out fully until it's locked (with a click). Move a projector by holding two handles by 2 or more people.

To retract carrying handles, pull up lock buttons and release lock of handles and press handles fully in until it's locked.

Pull up lock buttons to release lock.

PREPARATION

Page 12

CONNECTING PROJECTOR

TERMINALS OF PROJECTOR

This projector applies various input/output terminals and 4 terminal slots for expansion to tune to diversity of signals from computers and video equipment. 4-built-in Terminal Slots enable you to arrange desired combinations of input sources just by changing Terminal Boards. For Terminal Boards, contact sales dealer where you purchased a projector.

Pull out terminal by holding handle.

Remove 2 Screws on terminal.

REPLACEMENT OF TERMINAL

Tighten screws to secure terminal.

Replace terminal. Insert terminal along Guide to fit Plug into Socket.

ANALOG RGB

R/Pr G/Y B/Pb H/HV V

CONTROL PORT

DVI

INPUT 1

R/C JACK

USB

RESET

(MONO)

CONTROL PORT

AUDIO

CONTROL PORT

S-VIDEO

VIDEO/Y

INPUT 2INPUT 3

INPUT 4

AUDIO

SERIAL PORT IN

SERIAL PORT OUT

AUDIO OUT

Page 13

CONNECTING PROJECTOR

The port is not functioning in this model.

Connect S-VIDEO output from video equipment to this jack. (Refer to P16.)

Connect audio output from computer or video equipment to these jacks. (Refer to P15, 16.)

CONTROL PORT CONNECTORS

AUDIO INPUT JACKS

5 BNC INPUT JACKS

S-VIDEO INPUT JACK

Connect component video output (Cr, Y, Cb or Pr, Y, Pb) from video equipment to R/Pr, G/Y and B/Pb jacks or connect computer output [5 BNC Type (Red, Green, Blue, Horiz. Sync and Vert. Sync.)] from computer to R/Pr, G/Y, B/Pb, H/HV and V jacks. (Refer to P15,

16.)

Connect computer output (Digital/Analog DVI-I type) to this terminal. (Refer to P15.) HD (HDCP Compatible) signal can also be connected. (Refer to P16.)

DVI INPUT TERMINAL

INPUT/OUTPUT TERMINALS AND JACKS

Connect computer output (Analog HDB 15-pin type) to this terminal. (Refer to P15.)

HDB 15-PIN INPUT TERMINAL

AV INPUT (VIDEO/Y, C) JACKS

Connect composite video output from video equipment to VIDEO/Y jack or connect Separate Y/C video outputs to VIDEO/Y and C jacks. (Refer to P16.)

INPUT 2

INPUT 1 INPUT 1, 2, 3, 4

INPUT 1, 2, 4

INPUT 3

INPUT 4

INPUT 3

SERIAL PORT IN

SERIAL PORT OUT

R/C JACK

AUDIO OUT

USB

RESET

R/Pr G/Y B/Pb H/HV V

VIDEO/Y

ANALOG RGB

AUDIO

DVI

S-VIDEO

AUDIO

CONTROL PORT

(MONO)

CONTROL PORT

INPUT 1

INPUT 2INPUT 3

(MONO)

INPUT 4

Page 14

CONNECTING PROJECTOR

Connect an external audio amplifier to these jacks. (Refer to P15, 16.)

AUDIO OUTPUT JACKS

This projector uses a micro processor to control unit. Occasionally, micro processor may malfunction and need to be reset. This can be done by pressing RESET button with a pen, which will shut down and restart unit. Do not use RESET function excessively.

RESET BUTTON

When using Wired / Wireless Remote Control Unit as Wired Remote Control, Connect Wired Remote Control Unit to this jack with Remote Control Cable (supplied). (Refer to page 19.)

R/C JACK

USB PORT (Series B)

DVI

AUDIO

CONTROL PORT

R/C JACK

USB

(MONO)

RESET

(MONO)

AUDIO

CONTROL PORT

(MONO)

CONTROL PORT

(MONO)

R/Pr G/Y B/Pb H/HV V

VIDEO/Y

ANALOG RGB

S-VIDEO

INPUT 1

INPUT 2INPUT 3

INPUT 4

Page 15

CONNECTING PROJECTOR

CONNECTING TO COMPUTER

IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA / SXGA/WXGA/UXGA)

VGA Cable

Monitor Output

Desktop type Laptop type

Audio Cable

(stereo)

✽

Audio Output

Audio Input

AUDIO OUT

Cables used for connection (✽ = Cables are not supplied with this projector.)

• VGA Cable (HDB 15 pin)

• DVI Cable

✽

• BNC Cable (BNC x 5) ✽

• Audio Cables (RCA x 2) ✽

Audio Cable

(stereo) ✽

NOTE :

When connecting cable, power cords of both a projector and external equipment should be disconnected from AC outlet. Turn a projector and peripheral equipment on before computer is switched on.

Terminals of

a Projector

Audio Amplifier

Audio Speaker

(stereo)

External Audio Equipment

Monitor Output

DVI Cable ✽

BNC Cable

✽

Monitor Output

SERIAL PORT IN

SERIAL PORT OUT

R/C JACK

USB

AUDIO OUT

RESET

(MONO)

DVI

R/Pr G/Y B/Pb H/HV V

VIDEO/Y

ANALOG RGB

S-VIDEO

AUDIO

CONTROL PORT

(MONO)

AUDIO

CONTROL PORT

(MONO)

AUDIO

(MONO)

AUDIO

CONTROL PORT

(MONO)

INPUT 1

INPUT 2INPUT 3INPUT 4

Page 16

CONNECTING PROJECTOR

Page 17

BEFORE OPERATION

IMAGE BUTTON

Used to select image level. (P31, 36)

AUTO PC ADJ.

IMAGE

SELECT

ZOOM FOCUS

LENS SHIFT

ON-OFF

INPUT 1/2

INPUT 3/4

SIDE CONTROLS AND INDICATORS

Used to adjust zoom. (P24)

INPUT 3/4 BUTTON

POWER ON–OFF BUTTON

FOCUS BUTTONS

Used to select input source either INPUT 3 or INPUT 4. (P26, 34)

Used to adjust focus. (P24)

Used to select an item or adjust value in MENU. It is also used to pan image in DIGITAL ZOOM mode. (P33)

Used to execute item selected. It is also used to expand image in DIGITAL ZOOM mode. (P33)

Used to turn a projector on or off. (P23)

ZOOM BUTTONS

Used to select LENS SHIFT function. (P24)

SELECT BUTTON

POINT BUTTONS

LENS SHIFT BUTTON

SIDE CONTROLS

MENU BUTTON

Used to open or close MENU operation. (P21, 22)

INPUT 1/2 BUTTON

Used to select input source either INPUT 1 or INPUT 2. (P26, 34)

SIDE CONTROLS

REAR INDICATORS

FRONT INDICATORS

AUTO PC ADJ. BUTTON

Page 18

BEFORE OPERATION

READY

LAMP

REPLACE

WARNING

TEMP.

READY INDICATOR

LAMP INDICATOR

LAMP REPLACE INDICATOR

This indicator lights green when a projector is ready to be turned on. And it flashes green in Power Management mode. (P40, 42, 50)

This indicator is dim when a projector is turned on. And bright when a projector is in stand-by mode. (P50)

INDICATORS

WARNING TEMP. INDICATOR

This indicator flashes red when internal projector temperature is too high. (P42, 50)

WARNING

TEMP.

READY

LAMP

REPLACE

LAMP

FRONT INDICATORS

REAR INDICATORS

This LAMP REPLACE indicator lights yellow when any of Projection Lamps is nearing its end, and flashes when any of them becomes out. Check which lamp needs to be replaced on Lamp Status Display.

(P42-44, 50)

Page 19

BEFORE OPERATION

OPERATION OF REMOTE CONTROL

LIGHT BUTTON

Lights the buttons on the remote control for about 10 seconds.

Used to select input source. (P26, 34)

POWER ON-OFF BUTTON

Used to turn projector on or off. (P23)

MENU BUTTON

Used to select MENU operation. (P21, 22)

INPUT 1, 2, 3, 4 BUTTONS

AUTO PC ADJ. BUTTON

Used to operate AUTO PC Adjustment function. (P28)

FREEZE BUTTON

Used to freeze picture. (P25)

SELECT BUTTON

POINT (UP / DOWN / LEFT / RIGHT) BUTTONS

Used to select an item or adjust value in ON-SCREEN MENU. They are also used to pan image in DIGITAL ZOOM +/– mode. (P33)

Used to execute item selected. It is also used to expand / compress image in DIGITAL ZOOM mode. (P33)

Used to adjust zoom. (P24)

ZOOM BUTTONS

FOCUS BUTTON

Used to adjust focus. (P24)

NO SHOW BUTTON

Used to turn picture into black image. (P25)

D.ZOOM BUTTON

Used to select DIGITAL ZOOM +/– mode and resize image. (P33)

KEYSTONE BUTTON

Used to correct keystone distortion. (P24, 39)

IMAGE SEL. BUTTON

Used to select image level. (P31, 36)

WIRED REMOTE JACK

When using as Wired Remote Control, connect Remote Control Cable (supplied) to this jack. Battery installation is required when using as Wired Remote Control.

LENS SHIFT BUTTON

Used to select LENS SHIFT function. (P24)

IMAGE ADJ. BUTTON

Used to adjust image level. (P37-38)

Used to operate P-TIMER function. (P25)

P-TIMER BUTTON

Page 20

BEFORE OPERATION

16.4’ (5 m)

60°

16.4’ (5 m)

60°

To insure safe operation, please observe following precautions :

● Use (2) AA or R06 type alkaline batteries.

● Replace two batteries at same time.

● Do not use a new battery with an used battery.

● Avoid contact with water or liquid.

● Do not expose Remote Control Unit to moisture, or heat.

● Do not drop Remote Control Unit.

● If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries.

● Danger of explosion if battery is incorrectly replaced.

● Dispose of used batteries according to batteries manufacturers instructions and local rules.

Pull up lid and remove it.

Remove battery compartment lid.

Slide batteries into compartment.

Replace compartment lid.

Two AA size batteries

For correct polarity (+ and –), be sure battery terminals are in contact with pins in compartment.

REMOTE CONTROL BATTERIES INSTALLATION

1 2 3

Operating Range

Point Remote Control Unit toward projector (Infrared Remote Receiver) whenever pressing any button. Maximum operating range for Remote Control Unit is about 16.4’ (5m) and 60° in front and rear of a projector.

Page 21

BEFORE OPERATION

HOW TO OPERATE ON-SCREEN MENU

FLOW OF ON-SCREEN MENU OPERATION

Display ON-SCREEN MENU

Press MENU button to display ON-SCREEN MENU (MENU BAR). A red frame is POINTER.

Move POINTER (red frame) to MENU ICON that you want to select by pressing POINT LEFT / RIGHT buttons.

Adjust ITEM DATA by pressing POINT LEFT / RIGHT buttons. Refer to following pages for details of respective adjustments.

Press POINT DOWN button and move POINTER (red frame or red arrow) to ITEM that you want to adjust, and then press SELECT button to show ITEM DATA.

Select Menu to be adjusted

Control or adjust item through ON-SCREEN MENU

You can control and adjust this projector through ON-SCREEN MENU. Refer to following pages to operate each adjustment on ON-SCREEN MENU.

2 MOVING POINTER

3 SELECT ITEM

Move pointer (✽ see below) or adjust value of item by pressing POINT button(s) on Side Control or on Remote Control Unit.

Select item or set selected function by pressing SELECT button.

OPERATING ON-SCREEN MENU

✽ Pointer is a icon on ON-SCREEN MENU to select item. See fig-

ures on section "FLOW OF ON-SCREEN MENU OPERATION" below.

Used to select item.

SELECT BUTTON

Used to move Pointer UP/ DOWN/ RIGHT/ LEFT.

POINT BUTTONS

SIDE CONTROL

MENU BAR

POINTER (red frame)

MENU ICON

ITEM DATA Press POINT LEFT/RIGHT buttons to adjust value or set function.

SELECT

BUTTON

POINTER (red frame) Press POINT DOWN button to move POINTER.

1 DISPLAY MENU

Press MENU button to display ON-SCREEN MENU.

ITEM

Used to select the item.

SELECT BUTTON

Used to move a Pointer UP/ DOWN/ RIGHT/ LEFT.

POINT BUTTONS

REMOTE CONTROL UNIT

MENU BUTTON

AUTO PC ADJ.

LENS SHIFT

SELECT

IMAGE

Page 22

BEFORE OPERATION

MENU BAR

PC SYSTEM MENU

Used to select computer system. (Refer to P27)

IMAGE ADJUST MENU

Used to adjust computer image. [Contrast/Brightness /Color Temp. /White Balance (R/G/B) /Sharpness/Gamma /Noise Reduction /Progressive] (Refer to P32)

SETTING MENU

Used to change settings of projector or reset Lamp Replace Counter. (Refer to P39-41)

IMAGE SELECT MENU

Used to select image level among Standard, Real and Image 1 ~ 4. (Refer to P31)

FOR PC SOURCE

Press MENU BUTTON while connecting to PC input source.

AV SYSTEM MENU

Used to select system of selected video source. (Refer to P35)

IMAGE ADJUST MENU

Used to adjust picture image.

[Contrast/Brightness/Color /Tint/Color Temp. /White balance (R/G/B) /Sharpness/Gamma /Noise Reduction/Progressive]

(Refer to P37, 38)

FOR VIDEO SOURCE

Press MENU BUTTON while connecting to VIDEO input source.

Same function as Menu for PC source.

INPUT MENU

Used to select input source (Input 1, Input 2, Input 3 or Input 4). Refer to P34

PC ADJUST MENU

Used to adjust parameters to match with input signal format. (Refer to P28-30)

IMAGE SELECT MENU

Used to select image level among Standard, Cinema and Image 1 ~ 4. (Refer to P36)

SCREEN MENU

Used to set size of image to Normal or Wide. (Refer to P38)

GUIDE WINDOW

Shows selected item of ONSCREEN MENU.

Same function as Menu for PC source.

INPUT MENU

Used to select input source (Input 1, Input 2, Input 3 or Input 4). Refer to P26

SCREEN MENU

Used to adjust size of image. [Normal / True / Wide / Digital zoom +/–] (Refer to P33)

Page 23

BASIC OPERATION

TURNING ON PROJECTOR

TURNING OFF PROJECTOR

TURNING ON / OFF PROJECTOR

Power off?

Message disappears after 4 seconds.

Connect a projector's AC Power Cord into a wall outlet and turn MAIN ON/OFF SWITCH to ON. LAMP indicator lights RED, and READY indicator lights GREEN.

Press POWER ON-OFF button on Side Control or on Remote Control Unit to ON. LAMP indicator dims, and Cooling Fans start to operate. Preparation Display appears on a screen and countdown starts. Signal from source appears after 20 seconds. Current Input position and Lamp status are also displayed on screen for 5 seconds. (Refer to "LAMP MANAGEMENT" on page 43.)

Press POWER ON-OFF button on Side Control or on Remote Control Unit, and a message "Power off?" appears on a screen.

TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF.

Complete peripheral connections (with Computer, VCR, etc.) before turning on projector. (Refer to "CONNECTING TO PROJECTOR" on Pages 13~16 for connecting that equipment.)

Preparation Display disappears after 20 seconds.

When Power Management function is ON, projector detects signal interruption and turns off Projection Lamp automatically. Refer to “Power Management” on pages 39 and 40.

Press POWER ON-OFF button again to turn off projector. LAMP indicator lights bright and READY indicator turns off. After approximate 90 seconds, READY indicator will light green again and projector may be turned on by pressing POWER ON-OFF button.

Cooling fans will operate for approximate 2 minutes after projector is turned off. To power down completely, turn MAIN ON/OFF SWITCH to OFF and disconnect AC Power Cord.

LAMP STATUS

INPUT 1

2 4

When WARNING TEMP. indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on projector again.

When both WARNING TEMP. and READY indicators to flash, follow procedures below:

1. Turn MAIN ON/OFF SWITCH to OFF.

2. Turn a projector on again.

When WARNING TEMP. indicator continues to flash, follow procedures below:

1. Turn MAIN ON/OFF SWITCH to OFF and disconnect AC Power Cord from an AC outlet.

2. Check Air Filters for dust accumulation.

3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 42.)

4. Turn a projector on again.

If WARNING TEMP. indicator should still continue to flash, contact sales dealer where you purchased this projector or service center.

Page 24

BASIC OPERATION

KEYSTONE ADJUSTMENT

Press KEYSTONE button on Remote Control Unit or select Keystone on SETTING menu. (Refer to page 39.) Keystone dialog box appears.

Correct keystone distortion by pressing POINT UP/DOWN button(s). Press POINT UP button to reduce upper part of image, and press POINT DOWN button to reduce lower part.

Reduce upper width with POINT UP button. Reduce lower width with POINT DOWN button.

If a projected picture has keystone distortion, correct image with KEYSTONE adjustment.

ADJUSTING SCREEN

Message disappears after 4 seconds.

Zoom

Focus

ZOOM ADJUSTMENT

FOCUS ADJUSTMENT

Press ZOOM ▲/▼ button on Side Control or on Remote Control Unit. Message “Zoom” is displayed.

Press ZOOM ▲ button to make image larger, and press ZOOM ▼ button to make image smaller.

Press FOCUS ▲/▼ button on Side Control or on Remote Control Unit. Message “Focus” is displayed.

Adjust focus of image by pressing FOCUS ▲/▼ button(s) .

LENS SHIFT ADJUSTMENT

Message disappears after 4 seconds.

Lens shift

Press the LENS SHIFT button on Side Control or on the Remote Control Unit. Message “Lens shift” is displayed.

Press POINT UP button to move image up, press POINT DOWN button to move image down, press POINT LEFT to move image left and press POINT RIGHT to move image right.

Message disappears after 4 seconds.

Page 25

BASIC OPERATION

Press FREEZE button on Remote Control Unit to freeze picture on-screen. To cancel FREEZE function, press FREEZE button again or press any other button except POINT UP/DOWN/LEFT/RIGHT and SELECT button.

PICTURE FREEZE FUNCTION

Press NO SHOW button on Remote Control Unit to black out a image. To restore to normal, press NO SHOW button again or press any other button except POINT UP/DOWN/LEFT/RIGHT and SELECT button.

NO SHOW FUNCTION

Message disappears after 4 seconds.

No show

Press P-TIMER button on Remote Control unit. Timer display “00 : 00” appears on a screen and timer starts to count time (00 : 00 ~ 59 : 59). To stop P-TIMER display, press P-TIMER button. And then, press P-TIMER button again to cancel P-TIMER function.

P-TIMER FUNCTION

Page 26

COMPUTER INPUT

SELECTING COMPUTER SYSTEM

WHEN SELECT INPUT 1 (DVI INPUT TERMINAL )

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to INPUT Menu icon.

Press POINT DOWN button to move a red arrow pointer to Input 1 and then press SELECT button. Source Select Menu will appear.

Input 1

INPUT MENU

Move a pointer to source that you want to select and then press SELECT button.

SELECTING INPUT SOURCE

MENU OPERATION

DIRECT OPERATION

Select INPUT source by pressing INPUT 1/2, INPUT 3/4 or INPUT 1 - INPUT 4 buttons on Side Control or on Remote Control Unit.

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to select Input and press SELECT button.

Another dialog box INPUT SELECT

Menu will appear.

Press POINT DOWN button to move arrow to INPUT source that you want to select, and then press SELECT button.

INPUT 1/2 button

INPUT 1

INPUT 2

Move a pointer (red arrow) to source and press SELECT button.

Move a pointer (red arrow) to Input 1 and press SELECT button.

INPUT Menu icon

Source Select Menu

INPUT 3/4 button

INPUT 3

INPUT 4

INPUT Menu icon

When your computer is connected on DVI terminal, select RGB (PC Digital).

RGB (AV HDCP)

When your computer is connected on DVI terminal, select RGB (Analog).

RGB (PC Digital)

RGB (Scart)

When scart video equipment is connected on DVI terminal, select RGB (Scart).

If a HDCP-compatible signal source is connected on DVI terminal, select RGB (AV HDCP).

NOTE; HDCP (High-bandwidth Digital Content Protection) is a system for protecting digital entertainment content which is delivered by DVI (Digital Visual Interface) from being copied. The specification of HDCP is decided and controlled by Digital Content Protection, LLC. Should the specification be changed, this projector may not display the digital content protected by HDCP.

RGB (Analog)

Page 27

COMPUTER INPUT

This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA, SXGA, WXGA or UXGA (refer to “COMPATIBLE COMPUTER SPECIFICATIONS” on page 51-52). When selecting Computer, this projector automatically tunes to incoming signal and projects proper image without any special setting. (Some computers need setting manually.)

Note : Projector may display one of following messages.

When projector cannot recognize connected signal as PC system provided in this projector, Auto PC Adjustment function operates to adjust projector and message “Auto” is displayed on SYSTEM Menu icon. (Refer to P28.) When image is not provided properly, manual adjustment is required. (Refer to P29 and 30.)

There is no signal input from computer. Make sure connection of computer and a projector is set correctly. (Refer to TROUBLESHOOTING on page 47.)

Auto

––––

PC SYSTEM Menu icon Displays system being selected.

PC SYSTEM MENU

SELECT COMPUTER SYSTEM MANUALLY

PC SYSTEM Menu icon Displays system being selected.

Systems on this dialog box can be selected.

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to PC SYSTEM Menu icon.

Press POINT DOWN button to move a red arrow pointer to system that you want to set, and then press

SELECT button.

PC SYSTEM MENU

Custom Mode (1~5) set in PC ADJUST Menu. (P29, 30)

This projector automatically selects PC system among those provided in this projector and PC system can be also selected manually.

AUTOMATIC MULTI-SCAN SYSTEM

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to INPUT Menu icon.

Move a pointer to "RGB", and then press SELECT button.

When connect a computer output [5 BNC Type (Red, Green, Blue, Horiz. Sync and Vert. Sync.)] from a computer to R/Pr, G/Y, B/Pb, H/HV and V jacks.

WHEN SELECT INPUT 2 (5 BNC INPUT JACKS )

Input 2

INPUT MENU

Move a pointer to RGB and press SELECT button.

INPUT Menu icon

Move a pointer (red arrow) to Input 2 and press SELECT button.

Source Select Menu

Press POINT DOWN button to move a red arrow pointer to Input 2 and then press SELECT button. Source Select Menu will appear.

Page 28

COMPUTER INPUT

PC ADJUSTMENT

AUTO PC ADJUSTMENT

Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your computer. Auto PC Adjustment function can be operated as follows.

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to PC ADJUST Menu icon.

Press POINT DOWN button to move a red frame pointer to AUTO PC Adj. icon and then press SELECT button twice. This Auto PC Adjustment can be also executed by pressing AUTO PC ADJ. button on Side Control or on Remote Control Unit.

Move a red frame pointer to AUTO PC Adj. icon and press SELECT button.

PC ADJUST MENU

Auto PC Adj.

PC ADJUST Menu icon

Store adjustment parameters. Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, setting can be done just by selecting Mode in PC SYSTEM Menu (P27). Refer to step 3 of MANUAL PC ADJUSTMENT section (P30).

NOTE

● Fine sync, Total dots and Picture Position of some computers can not be fully adjusted with this Auto PC Adjustment function. When image is not provided properly through this function, manual adjustments are required. (Refer to page 29, 30.)

● Auto PC Adjustment function cannot be operated in Digital Signal input on DVI terminal and “480i”, “575i”, “480p”, “575p”, “720p (HDTV)”, “1035i (HDTV)”, “1080i/50 (HDTV)” or “1080i/60 (HDTV)” is selected on PC SYSTEM Menu (P27).

Page 29

COMPUTER INPUT

MANUAL PC ADJUSTMENT

This projector can automatically tune to display signals from most personal computers currently distributed. However, some computers employ special signal formats which are different from standard ones and may not be tuned by Multi-Scan system of this projector. If this happens, projector cannot reproduce a proper image and image may be recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture. This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This enables you to recall setting for a specific computer whenever you use it.

Note : This PC ADJUST Menu cannot be operated in Digital Signal input on DVI terminal is selected on PC SYSTEM MENU

(P27).

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to PC ADJUST Menu icon.

Press POINT DOWN button to move a red frame pointer to item that you want to adjust and then press SELECT button. Adjustment dialog box will appear. Press POINT LEFT/RIGHT button to adjust value.

Move a red frame icon to item and press SELECT button.

PC ADJUST MENU

PC ADJUST Menu icon

Adjusts an image as necessary to eliminate flicker from display. Press POINT LEFT/RIGHT button to adjust value.(From 0 to 31.)

Fine sync

Number of total dots in one horizontal period. Press POINT LEFT/RIGHT button(s) and adjust number to match your PC image.

Total dots

Adjusts horizontal picture position. Press POINT LEFT/RIGHT button(s) to adjust position.

Horizontal

Adjusts vertical picture position. Press POINT LEFT/RIGHT button(s) to adjust position.

Vertical

Press SELECT button to show information of computer selected.

Current mode

Adjusts clamp position. When a image has a dark bar(s), try this adjustment.

Clamp

Press SELECT button at this icon to adjust “Clamp,” “Display area (H/V)” or set “Full screen.”

Press POINT LEFT/RIGHT button to adjust value.

Shows status (Stored / Free) of selected Mode.

Selected Mode

Press SELECT button at Current mode icon to show information of computer connected.

Current mode

Page 30

COMPUTER INPUT

NOTE : Fine sync, Display area, Display area H, Display area V and

Full screen cannot be adjusted when “480i”, “575i”, “480p”, “575p”, “720p (HDTV)”, “1035i (HDTV)”, “1080i/50 (HDTV)” or “1080i/60 (HDTV)” is selected on PC SYSTEM Menu (P27).

Selects area displayed with this projector. Select resolution at Display area dialog box.

Display area

Adjustment of horizontal area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button.

Display area H

Adjustment of vertical area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button.

Display area V

Press POINT LEFT/RIGHT button(s) to switch Full screen function to “On” or “Off.” Set “On” to resize image with 4 x 3 aspect ratio to fit a screen.

Full screen

Reset

Store

Closes PC ADJUST MENU.

Quit

Other icons operates as follows.

To store adjustment parameters, move a red frame pointer to Store icon and then press SELECT button. Move a red arrow pointer to any of Mode 1 to 5 that you want to store and then press SELECT button.

Reset all adjust parameters on adjustment dialog box to previous figure.

Mode free

Vacant Mode Shows values of “Total dots,”

“Horizontal,” “Vertical,” “Display area H,” and “Display area V.”

Store icon

Mode free icon

Close this dialog box.

To store adjustment data.

To clear adjustment data.

To clear adjustment parameters previously set, move a red frame pointer to Mode free icon and then press SELECT button. Move a red arrow pointer to Mode that you want to clear and then press SELECT button.

Display area

Press POINT LEFT /RIGHT button(s) to adjust value and then press SELECT button.

Press SELECT button at Display area icon and Display area dialog box appears.

This Mode has parameters being stored.

Page 31

COMPUTER INPUT

PICTURE IMAGE ADJUSTMENT

IMAGE LEVEL SELECT (MENU)

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to IMAGE SELECT Menu icon.

Press POINT DOWN button to move a red frame pointer to level that you want to set and then press SELECT button.

Move a red frame icon to level and press SELECT button.

Level being selected.

IMAGE SELECT MENU

Normal picture level preset on this projector.

Standard

Picture level with improved halftone for graphics.

Real

User preset picture adjustment in IMAGE ADJUST Menu (P32).

IMAGE 1~4

IMAGE SELECT Menu icon

IMAGE LEVEL SELECT (DIRECT)

Select image level among Standard, Real, Image 1, Image 2, Image 3 and Image 4 by pressing IMAGE/IMAGE SEL. button on Side Control or on Remote Control Unit.

IMAGE button

Standard

Real

Image 1

Image 2

Image 3

Image 4

Normal picture level preset on this projector.

Picture level with improved halftone for graphics.

User preset picture adjustment in IMAGE ADJUST Menu (P32).

Standard

Real

IMAGE 1~4

Page 32

COMPUTER INPUT

Press POINT LEFT/RIGHT buttons to adjust value.

Reset all adjustment to previous figure.

Reset

Store

Closes IMAGE ADJUST MENU.

Quit

Other icons operates as follows.

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to IMAGE ADJUST Menu icon.

Press POINT DOWN button to move a red frame pointer to item that you want to adjust and then press SELECT button. Level of each item is displayed. Adjust each level by pressing POINT LEFT/RIGHT button(s).

Move a red frame pointer to item to be selected and then press SELECT button.

IMAGE ADJUST MENU

IMAGE LEVEL ADJUSTMENT

Press POINT LEFT button to decrease contrast, and POINT RIGHT button to increase contrast. (From 0 to 63.)

Press POINT LEFT button to adjust image darker, and POINT RIGHT button to adjust brighter. (From 0 to 63.)

Contrast

Brightness

Press either POINT LEFT button or POINT RIGHT button to obtain better balance of contrast. (From 0 to 15.)

Gamma

To store manually preset image, move a red frame pointer to Store icon and press SELECT button. Image Level Menu will appear. Move a red frame pointer to Image 1 to 4 where you want to set and then press SELECT button.

Image Level Menu Move a red frame pointer to any of Image 1 to 4 where you want to set and then press SELECT button.

Store icon Press SELECT button at this icon to store adjustment.

IMAGE ADJUST Menu icon

Press POINT LEFT button to lighten red tone and POINT RIGHT button to deeper tone. (From 0 to 63.)

White balance (Red)

Press POINT LEFT button to lighten green tone and POINT RIGHT button to deeper tone. (From 0 to 63.)

White balance (Green)

Press POINT LEFT button to lighten blue tone and POINT RIGHT button to deeper tone. (From 0 to 63.)

White balance (Blue)

Selected Image level

Press POINT LEFT button to soften image, and POINT RIGHT button to sharpen image. (From 0 to 15.)

Sharpness

Progressive

Press POINT LEFT/RIGHT button(s) to change progressive scan mode. Dialog box display is changed to “Off” and progressive scan mode to off. Press POINT LEFT/RIGHT button(s) again, progressive scan mode to on.

NOTE :

Color temp.

Press either POINT LEFT button or POINT RIGHT button to Color temp. level that you want to select. (XLow, Low, Mid or High)

Press POINT LEFT/RIGHT button(s) to change noise reduction mode. Dialog box display is changed to “On” to reduce noise (rough parts) of image. Press POINT LEFT/RIGHT button(s) again, to change noise reduction mode to off.

Noise reduction

● Noise reduction can be operated when “480i”,

“575i”, “480p”, “575p”, “720p (HDTV)”, “1035i (HDTV)”, “1080i/50 (HDTV)” or “1080i/60 (HDTV)” is selected on PC SYSTEM MENU (P27) only.

● Progressive can be operated when “480i”, “575i”, “1035i (HDTV)”, “1080i/50 (HDTV)” or “1080i/60 (HDTV)” is selected on PC SYSTEM MENU (P27) only.

Page 33

COMPUTER INPUT

PICTURE SCREEN ADJUSTMENT

This projector has a picture screen resize function, which enables you to display desirable image size.

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to SCREEN Menu icon.

When Digital Zoom + is selected, ON-SCREEN MENU disappears and message “D. Zoom +” is displayed. Press SELECT button to expand image size. And press POINT UP/DOWN/LEFT/RIGHT button(s) to pan image. Panning function can work only when image is larger than screen size. Press D.ZOOM button on Remote Control Unit. The message “D. Zoom +” is displayed. Press SELECT button to expand image size.

To cancel Digital Zoom +/– mode, press any button except SELECT, POINT UP/DOWN/LEFT/RIGHT and AUTO PC ADJ. buttons.

Move a red frame to function and press SELECT button.

Press POINT DOWN button and move a red frame pointer to function that you want to select and then press SELECT button.

Wide

Digital Zoom +

NOTE

● Picture screen adjustment cannot be operated when “720p (HDTV)”, “1035i (HDTV)”, “1080i/50 (HDTV)” or “1080i/60 (HDTV)” is selected on PC SYSTEM Menu (P27).

● True and Digital Zoom +/– cannot be operated when “480i”, “575i”, “480p” or “575p” is selected on PC SYSTEM Menu (P27).

● This projector cannot display any resolution higher than 1600 X 1200. If your computer’s screen resolution is higher than 1600 X 1200, reset resolution to lower before connecting projector.

● Image data in other than XGA (1024 x 768) is modified to fit screen size in initial mode.

● Panning function may not operate properly if computer system prepared on PC ADJUST Menu is used.

Provides image to fit screen size.

Normal

True

SCREEN MENU

SCREEN Menu icon

When Digital Zoom – is selected, ON-SCREEN MENU disappears and message “D. Zoom –” is displayed. Press SELECT button to compress image size. Press D.ZOOM button twice on Remote Control Unit. The message “D. Zoom –” is displayed. Press SELECT button to compress image size.

Digital Zoom –

Provides image to fit wide video aspect ratio (16 : 9) by expanding image width uniformly. This function can be used for providing a squeezed video signal at 16 : 9.

Provides image in its original size. When original image size is larger than screen size (1024 x 768), this projector enters “Digital zoom +” mode automatically.

Page 34

VIDEO INPUT

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to INPUT Menu icon.

Press POINT DOWN button to move a red arrow pointer to Input 3 and then press SELECT button. Source Select Menu will appear.

Move a pointer to source and press SELECT button.

Source Select Menu (VIDEO)

Move a pointer to source that you want to select and then press SELECT button.

When video input signal is connected to VIDEO jack, select Video.

Video

When video input signal is connected to S-VIDEO jack, select S-Video.

S-Video

When video input signal is connected to VIDEO/Y, C jacks, select Y/C.

Y/C

When connecting to those equipment, select a type of Video source in SOURCE SELECT (VIDEO) Menu.

WHEN SELECT INPUT 3 (AV TERMINAL )

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to INPUT Menu icon.

Move a pointer to "Y, Pb/Cb, Pr/Cr" and then press SELECT button.

When connect component video output (Cr, Y, Cb or Pr, Y, Pb) from video equipment to R/Pr, G/Y and B/Pb jacks.

WHEN SELECT INPUT 2 (5 BNC SLOT )

Input 2

INPUT MENU

Move a pointer to Y, Pb/Cb, Pr/Cr and press SELECT button.

INPUT Menu icon

Move a pointer (red arrow) to Input 2 and press SELECT button.

Source Select Menu

Input 3

INPUT MENU

INPUT Menu icon

Move a pointer (red arrow) to Input 3 and press SELECT button.

Press POINT DOWN button to move a red arrow pointer to Input 2 and then press SELECT button. Source Select Menu will appear.

SELECTING INPUT SOURCE

MENU OPERATION

DIRECT OPERATION

Select INPUT source by pressing INPUT 1/2, INPUT 3/4 or INPUT 1 - INPUT 4 buttons on Side Control or on Remote Control Unit.

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to select Input and press SELECT button.

Another dialog box INPUT SELECT

Menu will appear.

INPUT 1/2 button

INPUT 1

INPUT 2

INPUT 3/4 button

INPUT 3

INPUT 4

INPUT Menu icon

Press POINT DOWN button to move arrow to INPUT source that you want to select, and then press SELECT button.

Page 35

VIDEO INPUT

AV SYSTEM MENU (VIDEO OR S-VIDEO)

AV SYSTEM MENU (COMPONENT VIDEO)

SELECTING VIDEO SYSTEM

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to AV SYSTEM Menu icon.

Press POINT DOWN button to move a red arrow pointer to system that you want to select and then press SELECT button.

If projector cannot reproduce proper video image, it is necessary to select a specific broadcast signal format among PAL, SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N.

Move pointer to system and press SELECT button.

PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N

Projector automatically detects incoming Video signal, and adjusts itself to optimize its performance. When Video System is 1035i, 1080i50 or 1080i60, select system manually first.

If projector cannot reproduce proper video image, it is necessary to select a specific component video signal format among 480i, 575i, 480p, 575p, 720p, 1035i , 1080i50 or 1080i60.

Auto

COMPONENT VIDEO SIGNAL FORMAT

VIDEO JACK OR S-VIDEO JACK

Y, Pb/Cb, Pr/Cr JACKS

Projector automatically detects incoming Video system, and adjusts itself to optimize its performance. When Video System is PAL-M or PAL-N, select system manually first.

Auto

AV SYSTEM Menu icon This box indicates system being selected.

Move pointer to system and press SELECT button.

AV SYSTEM Menu icon This box indicates system being selected.

Auto

1080i/60

1080i/50

720p

575p

480p

575i

480i

1035i

Page 36

VIDEO INPUT

PICTURE IMAGE ADJUSTMENT

IMAGE LEVEL SELECT (MENU)

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to IMAGE SELECT Menu icon.

Press POINT DOWN button to move a red frame pointer to level that you want to set and then press SELECT button.

Move a red frame pointer to level and press SELECT button.

Level being selected.

IMAGE SELECT MENU

Normal picture level preset on this projector.

Standard

Picture level adjusted for picture with fine tone.

Cinema

User preset picture adjustment in IMAGE ADJUST Menu (P38).

IMAGE 1~4

IMAGE SELECT Menu icon

IMAGE LEVEL SELECT (DIRECT)

Select image level among Standard, Cinema, Image 1, Image 2, Image 3 and Image 4 by pressing IMAGE/IMAGE SEL. button on Side Control or on Remote Control Unit.

Normal picture level preset on this projector.

Standard

Picture level adjusted for picture with fine tone.

Cinema

User preset picture adjustment in IMAGE ADJUST Menu (P38).

IMAGE 1~4

IMAGE button

Standard

Cinema

Image 1

Image 2

Image 3

Image 4

Page 37

VIDEO INPUT

Press POINT LEFT/RIGHT buttons to adjust value.

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to IMAGE ADJUST Menu icon.

Move a red frame pointer to item to be selected and then press SELECT button.

IMAGE ADJUST MENU

IMAGE LEVEL ADJUSTMENT

Press POINT LEFT button to decrease contrast, and POINT RIGHT button to increase contrast. (From 0 to 63.)

Press POINT LEFT button to adjust image darker, and POINT RIGHT button to adjust brighter. (From 0 to 63.)

Contrast

Brightness

Press either POINT LEFT button or POINT RIGHT button to obtain better balance of contrast. (From 0 to 15.)

Gamma

Press SELECT button at this icon to display other items.

IMAGE ADJUST Menu icon

Press POINT LEFT/RIGHT buttons to adjust value.

Press POINT LEFT button to lighten color, and POINT RIGHT button to deeper color. (From 0 to 63.)

Press POINT LEFT button or POINT RIGHT button to obtain proper color. (From 0 to 63.)

Color

Tint

Press POINT LEFT button to soften image, and POINT RIGHT button to sharpen image. (From 0 to 15.)

Sharpness

Press POINT LEFT button to lighten red tone and POINT RIGHT button to deeper tone. (From 0 to 63.)

White balance (Red)

Press POINT LEFT button to lighten green tone and POINT RIGHT button to deeper tone. (From 0 to 63.)

White balance (Green)

Press POINT LEFT button to lighten blue tone and POINT RIGHT button to deeper tone. (From 0 to 63.)

White balance (Blue)

Press SELECT button at this icon to store value.

Press SELECT button at this icon to display previous items.

Noise reduction

Progressive

NOTE :

Tint cannot be adjusted when video system is PAL, SECAM, PAL-M or PAL-N.

Progressive cannot be operated when “480p”, “575p” or “720p” is selected on AV SYSTEM MENU (P35).

Color temp.

Press either POINT LEFT button or POINT RIGHT button to Color temp. level that you want to select. (XLow, Low, Mid or High)

Page 38

VIDEO INPUT

PICTURE SCREEN ADJUSTMENT

This projector has a picture screen resize function, which enables you to display desirable image size.

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to SCREEN Menu icon.

Press POINT DOWN button and move a red frame pointer to function that you want to select and then press SELECT button.

NOTE : SCREEN Menu cannot be operated when

“720p”, “1035i”, “1080i/50” or “1080i/60” is selected on AV SYSTEM Menu (P35).

Move a red frame to function and press SELECT button.

SCREEN MENU

SCREEN Menu icon

Provides image at a wide screen ratio of 16 : 9.

Wide

Provides image at a normal video aspect ratio of 4 : 3.

Normal

To store adjustment data, move a red frame pointer to Store icon and press SELECT button. Image Level Menu will appear. Move a red frame pointer to Image Level 1 to 4 and then press SELECT button.

Image Level Menu Move a red frame pointer to image icon to be set and then press SELECT button.

Store icon

Reset all adjustment to previous figure.

Reset

Store

Closes IMAGE ADJUST MENU.

Quit

Other icons operates as follows.

Page 39

SETTING

Ceiling

When this function is “On,” picture is top/bottom and left/right reversed. This function is used to project image from a ceiling mounted projector.

Rear

When this function is “On,” picture is left/right reversed. This function is used to project image to a rear projection screen.

Ceiling function

Rear function

Keystone

When image is distorted vertically, select Keystone. ON-SCREEN MENU disappears and Keystone dialog box is displayed. Correct keystone distortion by pressing POINT UP/DOWN button(s). Refer to KEYSTONE ADJUSTMENT on page 24.

SETTING MENU

Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red-frame pointer to SETTING icon.

Language

Language used in ON-SCREEN MENU is selectable from among English, German, French, Italian, Spanish, Portuguese, Dutch, Swedish, Russian, Chinese, Korean and Japanese.

Display

This function decides whether to display On-Screen Displays.

On ··· shows all On-Screen Displays. Off ···· sets On-Screen Displays disappeared except;

● ON-SCREEN MENU

● “Power off?” message

● “No signal” message

● “Please wait....”

● P-Timer counter

Set a red frame pointer to item and press SELECT button.

Press POINT DOWN button to move a red-frame pointer to item that you want to set and then press

SELECT button. Setting

dialog box appears.

Blue back

When this function is “On,” this projector will produce a blue image instead of video noise on screen when any input source is unplugged or turned off.

Logo

When this function is “On,” projector displays our logo when starting up.

When pressing SELECT button at Language, Language Menu appears.

Move a pointer to item and then press POINT LEFT/RIGHT button(s).

SETTING MENU

SETTING Menu icon

Optional Control Number

Refer to page 12.

Page 40

SETTING

This function turns Projection Lamp off when this projector detects signal interruption and is not used for a certain period in order to reduce power consumption and maintain Lamp-life. (This projector is shipped with this function ON.)

Power Management function operates to turn Projection Lamp off when input signal is interrupted and any button is not pressed over 5 minutes. This function operates as follows;

1. When any input signal is interrupted, “No signal” and counting down display appears (for 5 minutes).

2. After counting down for 5 minutes, projector lamp and READY indicator are turned off.

3. When READY indicator flashing, Projection Lamp can be turned on again (Power Management mode). In this Power Management mode, Projection Lamp is automatically turned on when input signal connected or projector is operated with any button on Side Control or on Remote Control Unit again.

Power management

Time left until Lamp off.

Press SELECT button at this icon to display other items.

Lamp Mode

NOTE : After changing Lamp Mode, it cannot be switched again for 90 seconds.

This Projector is equipped with 4 Projection Lamps and a number of using lamps can be switched to 4 lamps or 2 lamps. Using 2 lamps maintain life of Projection Lamps.

To change over Lamp Mode

1. Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to select SETTING and press SELECT button. Setting dialog box appears.

2. Press POINT DOWN button to move a red frame pointer to “Lamp mode”. Set "4 lamps mode" or "2 lamps mode" by pressing POINT LEFT/RIGHT button(s). When Lamp Mode is set from "4 lamps mode" to "2 lamps mode" image becomes little darker. When Lamp Mode is set from "2 lamps mode" to "4 lamps mode" image become brighter gradually.

Press SELECT button at this icon to display previous items.

Move a pointer to item and then press POINT LEFT/RIGHT button(s).

This function allows you to change brightness of the screen.

···· normal brightness.

···· brightness according with the input signal.

···· lower brightness reduces the lamp power consumption

and extends the lamp life.

Lamp control

Page 41

SETTING

On start

When this function is “On,” projector is automatically turned on just by switching MAIN ON/OFF SWITCH on.

Note ; Be sure to turn projector off properly (refer to section

“TURNING OFF PROJECTOR” on P23). If projector is turned off in wrong steps, On Start function does not operate properly.

This projector provides eight different remote control codes (Code 1-Code 8); the factory-set, initial code (Code 1) and the other seven codes (Code 2 to Code 8). This switching function prevents remote control interference when operating several projectors or video equipment at the same time. For example operating the projector in “Code 7”, both the projector and the remote control must be switched to “Code 7”.

To change the code for the projector;

Select a remote control code in this Setting Menu.

To change the code for the remote control;

Check the Reset Switch to "Use position" in the compartment lid on back of the remote control. And then while holding down the MENU button, press the IMAGE button number of times corresponding to the remote control code for the projector.

To reset the code for the remote control;

Slide the Reset Switch to "Reset position" in the compartment lid on back of the remote control.

Remote control

When pressing the SELECT button at Remote control, the remote control code menu appears.

Use position

Reset position

Reset switch

Lamp counter reset

This function returns all setting values except the lamp counter to the factory default settings.

Closes SETTING MENU.

Quit

Factory default

This function is used to reset the lamp replace counter. When replacing the projection lamp, reset the lamp replace counter by using this function. See page 45 for operation.

Select Factory default and this box appears. Select [Yes], and the next box appears.

Factory default

Select [Yes] to activate it.

Remote control

Page 42

APPENDIX

READY

LAMP

REPLACE

WARNING

TEMP.

AIR FILTER CARE AND CLEANING

Turn power off, and disconnect AC power cord from AC outlet.

Pull out air filter from a projector.

Pulling up center frame of air filter top, separate air filter top and air filter from air filter base.

Clean each parts with brush out dust and particles. Be sure to dry them out.

Assemble sheet and air filter and replace air filter to a projector.

AIR FILTER

AIR FILTER TOP

AIR FILTER BASE

AIR FILTER

CAUTION

Do not operate a projector with Air Filter removed. Dust may accumulate on LCD Panel and Mirror degrading picture quality. Do not put small parts into Air Intake Vents. It may result in malfunction of a projector.

MAINTENANCE

WARNING TEMP. INDICATOR

Ventilation Slots of a projector may be blocked. In such an event, reposition a projector so that Ventilation Slots are not obstructed.

Air Filter may be clogged with dust particles. Clean Air Filter by following section AIR FILTER CARE AND CLEANING on this page.

If WARNING TEMP. Indicator remains on after performing above checks, Cooling Fans or Internal Circuits may be malfunctioning. Contact the service station.

The Warning Temp. Indicator flashes red to let you know the internal temperature of the projector exceeds the normal level. If the temperature goes up further, the projector will be turned off automatically and the Ready indicator will go out. (The Warning Temp. Indicator continues flashing.) After the cooling-off period, the Ready Indicator lights on again and the projector can be turned on by pressing the On/Off button on the remote control unit or on the side control. When you turn on the projector, the Warning Temp. Indicator will go out. If the Warning Temp. Indicator is still flashing, check the followings;

FRONT INDICATORS

When both of the Warning Temp. and Ready indicators are flashing:

Warning Temp. Indicator

Ready Indicator

When the projector detects an internal problem, it will shut down automatically and both of the Warning temp. and Ready Indicators starts flashing. In this condition, the projector cannot be turned on even if you press the On/Off button on the remote control unit or on the side control. If this case happenes, disconnect and reconnect the AC power cord, and then turn on the projector again to check its operation. If the projector shuts down again or fails to be turned on, the internal check and repair will be required. Plug off the AC power cord and contact service station.

WARN ING

TEMP.

READY

LAMP

REPLACE

LAMP

Page 43

APPENDIX

LAMP MANAGEMENT

This Projector is equipped with 4 Projection Lamps to ensure brighter image and those lamps are controlled by Lamp Management Function. Lamp Management Function detects status of all lamps and shows status on screen or on LAMP REPLACE indicator. This function also automatically controls Lamp Mode when any of lamps is out for end of life or malfunctions.

Projection Lamp lights normally.

Lamp Replace Indicator

This LAMP REPLACE indicator lights yellow when any of Projection Lamps is nearing its end, and flashes when any of them becomes out. Check number of lamp on Lamp Status Display and replace lamp.

Yellow Lamp

Dim Lamp

X Mark on Lamp

Red Lamp

LAMP REPLACE INDICATOR

Projection Lamp is turned off.

Projection Lamp is nearing its end. When image becomes darker or color becomes unnatural, replace lamp. (LAMP REPLACE indicator lights yellow.)

(LAMP REPLACE indicator flashes yellow.) Projection lamp is defective or fails to be turned on. Restart a projector on, and make sure lamp is on. If this mark still appears, replace lamp corresponding with number marked X.

LAMP STATUS DISPLAY

Lamp Mode Changeover

Lamp Management Function automatically changes combination of lighting lamp (Lamp Mode) by detecting status of lamp. When any of 4 lamps becomes out, Lamp Mode is changed over from 4 lamps to 2 lamps. And when any of 2 lamps are out, a projector operates with 1 lamp. Lamp Mode can be switched to 4 lamps or 2 lamps manually. Refer to SETTING section on page 39, 40

2 4

4 LAMP MODE

2 LAMP MODE (Example)

1 LAMP MODE (Example)

Lamp Status Display

Lamp Status Display appears on screen when power switch is on or changed input position (input 1, input 2, Input 3 or input 4). This shows status of each lamp as; ON, OFF, NEAR END, or OUT. Refer to following for each status.

LAMP STATUS

INPUT 1

2 4

Page 44

APPENDIX

Check number of lamp to be replaced on Lamp Status Display.

Remove two screws on Lamp Cover and press button to open Lamp Cover. (See right figure.)

Loosen two screws and pull out Lamp Assembly to be replaced by grasping handle.

Turn off a projector and disconnect AC Power Cord. Allow a projector to cool down for at least 45 minutes.

Replace Lamp Assembly with a new one and tighten two screws. Make sure Lamp is set properly

Follow these steps to replace lamp assembly.

Replace Lamp Cover and tighten two screws.

Connect AC Power Cord to a projector and turn a projector on.

Reset Lamp Replacement Counter. (Refer to section "Lamp Replace Counter" on page 45.)

NOTE : Do not reset LAMP REPLACEMENT COUNTER when

lamp is not replaced.

BUTTON

SCREWS

LAMP COVER

SCREWS

Make sure which number of lamp needs to be replaced on Lamp Status Display. Figure shows case of replacing LAMP 2.

LAMP 1

LAMP 2

LAMP 3

LAMP 4

CAUTION : DO NOT OPERATE A PROJECTOR WHILE ANY OF LAMPS IS REMOVED. IT MAY RESULT IN MALFUNCTIONS, FIRE HAZARD, OR OTHER ACCIDENTS.

NOTES ON LAMP REPLACEMENT

To maintain quality of picture (better balance of color and brightness in entire screen), we recommend replacing all 4 lamps at a time.

LAMP REPLACEMENT

When the life of the Projection Lamp of this projector draws to an end, the LAMP REPLACE indicator lights yellow. If this indicator lights yellow, replace the projection lamp with a new one promptly.

For continued safety, replace with a lamp assembly of the same type. Do not drop a lamp assembly or touch a glass bulb! The glass can shatter and may cause injury.

Allow a projector to cool, for at least 45 minutes before you open Lamp Cover. The inside of a projector can become very hot.

CAUTION

REAR INDICATORS

READY

LAMP

REPLACE

WARNING

TEMP.

RNING

TEMP.

READY

LAMP

REPLACE

LAMP

FRONT INDICATORS

LAMP REPLACE INDICATOR

TURN OFF THE UV LAMP BEFORE OPENING THE LAMP COVER.

WARNING:

Page 45

APPENDIX

ORDER REPLA

CEMENT LAMP

Replacement Lamp can be ordered through your dealer. When ordering a Projection Lamp, give the following information to the dealer.

●

Model No. of your projector : PLC-XF46N/E

● Replacement Lamp Type No. : POA-LMP100

(Service Parts No. 610 327 4928)

Move pointer to Lamp counter reset and then press SELECT button. Move arrow to

replaced lamp number (Lamp 1, Lamp 2, Lamp 3 or Lamp 4) and then press

SELECT button.

Be sure to reset Lamp Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP REPLACE indicator stops lighting.

Turn projector on, press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to SETTING Menu icon.

Press POINT DOWN button to move a red frame pointer to “Lamp counter reset” and then press

SELECT button.

Do not reset Lamp Replace Counter except after Projection lamp is replaced.

Another confirmation dialog box appears and select [Yes] to reset Lamp Replace Counter.

Move arrow to replaced lamp number (Lamp 1, Lamp 2, Lamp 3 or Lamp 4) and then press

SELECT button. Message "Lamp replace counter Reset?" is displayed. Move pointer to [Yes] and then press SELECT button.

NOTE: Be sure to reset correct lamp number otherwise LAMP

REPLACE indicator continues lighting.

Message "Lamp replace counter Reset?" is displayed. Move pointer to [Yes] and then press SELECT button.

Select [Yes] to activate it.

LAMP REPLACE COUNTER

2 4

Page 46

APPENDIX

This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may result in accidents, injury, or create a fire hazard.

● Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no

guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a shorter period of time than other similar lamps.

● If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE INDICATOR

lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. ( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual. ) Continuous use of the lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion.

● A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its

lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used.

IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.

If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector except those who are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken glass.

LAMP HANDLING PRECAUTIONS

SERVICE

WARNING: High voltages are used to operate this projector. Do not attempt to open cabinet.

You can often correct operating problems yourself. If a projector fails to work properly, see "TROUBLESHOOTING" section on page 47. To correct failure, try "Solutions".

If after following all operating instructions, you find that service is necessary, contact Sanyo Service Station or store where you purchased unit. Give model number and explain difficulty. We will advise you how to obtain service.

This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty and electrical hazards.

The CE Mark is a Directive conformity mark of the European Community (EC).

Pixelworks ICs used.

Page 47

APPENDIX

TROUBLESHOOTING

Before calling your dealer or service center for assistance, check matters below once again.

1. Make sure you have connected a projector to your computer or video equipment as described in section "CONNECTING PROJECTOR" on pages 13 ~ 16.

2. Check cable connection. Verify that all computer, video and power cord are properly connected.

3. Verify that all power is switched on.

4. If a projector still does not produce an image, re-start your computer.

5. If an image still does not appear, unplug a projector from your computer and check your computer monitor's display.Problem may be with your graphics controller rather than with a projector. (When you reconnect a projector, be sure to turn a computer and monitor off before you power up a projector. Power equipment back on in order of : Projector and computer.)

6. If problem still exists, check following chart.

No power.

● Plug a projector into your AC outlet.

● Turn MAIN ON/OFF switch to ON.

● Press POWER ON/OFF switch to ON.

● Make sure READY Indicator lights.

● Wait 90 seconds after a projector is turned OFF when turning a projector back on.

NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as

follows:

1. LAMP indicator lights bright and READY indicator turns off.

2. After 90 seconds, READY indicator lights green again and a projector may be turned on by pressing Power ON-OFF button.

● Check WARNING TEMP. and READY indicator. If both WARNING TEMP. and READY indicator flashes, a projector cannot be turned on. (See "TURNING ON/OFF PROJECTOR" section on page 23.)

● Check Projection Lamp. (Refer to page 44.)

Image is out of focus.

● Adjust focus of a projector.

● Check Projection Lens to see if it needs cleaning.

NOTE : Moving a projector from a cool temperature location to a warm temperature location

may result in moisture condensation on Projection Lens. In such an event, leave a projector OFF and wait until condensation disappears.

Picture is Left/Right reversed.

● Check Ceiling / Rear feature. (See “SETTING” section on page 39.)

Problem: Try these Solutions

Picture is Top/Bottom reversed.

● Check Ceiling feature. (See “SETTING” section on page 39.)

Some displays are not seen during Operation.

● Check Display feature.(See “SETTING” section on page 39.)

No image.

● Check connection between your computer or video equipment and a projector.

● When turning a projector on, it takes about 20 seconds to display an image.

● Check system that you select is corresponding with your computer or video equipment.

● Make sure temperature is not out of Operating Temperature (5°C ~ 35°C).

Remote Control Unit does not work.

● Check batteries.

● Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.

● Make sure you are not too far from a projector when using Remote Control Unit.

Maximum operating range is 16.4’ (5m).

● Check remote control code from Remote Control Unit. (See “SETTING” section on page 41.)

Page 48

APPENDIX

System (1)

SVGA 1 SVGA 2 SVGA 3

Auto PC Adj. Fine sync. Total dots Horizontal Vertical Current mode Clamp Display area

Display area - H Display area - V Full screen Reset Mode free Store

Quit

Standard Real Image 1 Image 2 Image 3 Image 4

Image Adjust

Contrast Brightness Color Temp

Red Green Blue

Gamma

Store

Quit

Normal True Wide Digital Zoom + Digital Zoom –

0 - 31

On/Off

0 - 63 0 - 63

Input

RGB (Analog)

RGB (Scart)

Go to System (1)

Input 2

Y, Pb/Cb, Pr/Cr

Computer Input

Input 3

Go to System (2)

Input 1

Video

S-Video

PC Adjust

640 x 480 720 x 400 800 x 600 1024 x 768 1152 x 864 1280 x 1024 1400 x 1050

Mode 1 Mode 2 Mode 3 Mode 4 Mode 5

Image Select

High

0 - 63 0 - 63 0 - 63

0 - 15

Image 1 Image 2 Image 3 Image 4

Screen

1600 x 1200

Quit

Yes/No

Quit

Mid

Reset

Yes/No

RGB

Low

XLow

Sharpness 0 - 15

N/A

Go to System (2)

Computer Input/Video Input

✽N/A

- - - not applicable

MENU TREE

Go to System (1)

Go to System (3)

Y/C

MODE 1

MODE 2

Quit

Noise reduction Off/On

Progressive Off/On

Input 4

Go to System (1)

RGB (PC Digital)

N/A

RGB (AV HDCP)

N/A

Page 49

APPENDIX

Auto PAL SECAM NTSC NTSC 4.43 PAL-M PAL-N

Video Input

Auto

1080i/50 1035i 720p 575p 480p 575i 480i

Standard Cinema Image 1 Image 2 Image 3 Image 4

Quit

0 - 63 0 - 63 0 - 63 0 - 63

Off/On

Language

Image Select

System (3)

System (2)

Image Adjust

Contrast Brightness Color Tint

Red Green Blue Sharpness

Reset Store

Gamma

Progressive

0 - 63 0 - 63 0 - 63 0 - 15 0 - 15

Image 1 Image 2 Image 3 Image 4

Screen

Setting

English German French Italian Spanish Portuguese Dutch Swedish

Chinese Korean Japanese

On/Off

On/Off On/Off

On/Off

4 Lamp/2 Lamp

Code 1

Yes / No

Keystone

Blue back

Display

Logo

Ceiling Rear

Power management

On start

Lamp mode

Remote control

Factory default

Yes/No

Quit

Code 2 Code 3 Code 4 Code 5 Code 6 Code 7 Code 8 Quit

Quit

Russian

HighColor Temp Mid Low XLow

Yes / NoLamp counter reset

Computer Input/Video Input

1080i/60

Off/OnNoise reduction

Normal

Normal/Auto/EcoLamp control

Quit

Wide

Page 50

APPENDIX

INDICATORS AND PROJECTOR CONDITION

Check the Indicators for projector condition.

• • • on : red

• • • dim

• • • off

• • • flashing : red

The projector is OFF. (The MAIN switch OFF position or the AC Power Cord is unplugged.)

The projector is READY to be turned on with the POWER ONOFF button.

The temperature inside the projector is abnormally high. The projector cannot be turned on. When the projector is cooled down enough and the temperature returns to normal, the READY indicator lights green and the projector can be turned on. (The WARNING TEMP. indicator keeps flashing.) Check and clean the Air Filter.

The projector is being cooled down. It cannot be turned on until the READY indicator lights green.

Projector Condition

The projector is operating normally.

The projector is cooled down enough and the temperature returns to normal. When turning on the projector, the WARNING TEMP. indicator stops flashing. Check and clean the Air Filter.

Indicators

READY

green

LAMP

red

The projector detects an abnormal condition and cannot be turned on. Unplug the AC Power Cord and plug it again to turn on the projector. If the projector is turned off again, disconnect the AC Power Cord and contact the dealer or the service center for service and checkup. Do not leave the projector on. It may cause electric shock or a fire hazard.

The projector is in the Power management mode.

✽

WARNING

TEMP.

red

LAMP

REPLACE

yellow

• • • on : green

• • • flashing : green

Page 51

APPENDIX

COMPATIBLE COMPUTER SPECIFICATIONS

––––––––

(Interlace)

1024 x 768

(Interlace)

ON-SCREEN

DISPLAY

RESOLUTION

H-Freq.

(kHz)

V-Freq.

(Hz)

VGA 1

640 x 480 31.47 59.88 VGA 2 720 x 400 31.47 70.09 VGA 3 640 x 400 31.47 70.09 VGA 4 640 x 480 37.86 74.38 VGA 5 640 x 480 37.86 72.81 VGA 6 640 x 480 37.50 75.00

MAC LC13

640 x 480 34.97 66.60

MAC 13 640 x 480 35.00 66.67

MAC 16 832 x 624 49.72 74.55

MAC 19 1024 x 768 60.24 75.08 MAC 21

1152 x 870

68.68 75.06

45.00 60.00

SVGA 1 800 x 600 35.156 56.25 SVGA 2 800 x 600 37.88 60.32 SVGA 3 800 x 600 46.875 75.00 SVGA 4 800 x 600 53.674 85.06 SVGA 5 800 x 600 48.08 72.19 SVGA 6 800 x 600 37.90 61.03 SVGA 7 800 x 600 34.50 55.38 SVGA 8 800 x 600 38.00 60.51 SVGA 9 800 x 600 38.60 60.31

SVGA 11 800 x 600 38.00 60.51

ON-SCREEN

DISPLAY

RESOLUTION

H-Freq.

(kHz)

V-Freq.

(Hz)

XGA 11

1024 x 768

XGA 13 1024 x 768 XGA 14 1024 x 768

61.00 75.70

XGA15 1024 x 768

46.90 58.20

XGA 8 1024 x 768

47.00 58.30

XGA 9

1024 x 768

(Interlace)

58.03 72.00

SXGA 1 1152 x 864 SXGA 2 1280 x 1024

63.48 79.35

SXGA 3 1280 x 1024

36.00 87.17

SXGA 4

1280 x 1024

64.20 70.40

SXGA 5 1280 x 1024

62.50 58.60

SXGA 6 1280 x 1024

63.90 60.00

SXGA 7

1280 x 1024

63.34 59.98

SXGA 8 1280 x 1024

63.74 60.01

SXGA 11

1152 x 900

71.69 67.19

SXGA 12

1152 x 900

81.13 76.107

SXGA 13

1280 x 1024

(Interlace)

63.98 60.02

SXGA 14

1280 x 1024

(Interlace)

61.20 65.20

71.40 75.60

50.00 86.00

50.00 94.00

XGA 1 1024 x 768 XGA 2 1024 x 768 XGA 3 1024 x 768 XGA 4 1024 x 768

48.36 60.00

68.677 84.997

XGA 6 1024 x 768

60.023 75.03

XGA 7 1024 x 768

56.476 70.07

48.50 60.02

44.00 54.58

SXGA 9 1280 x 1024

SXGA 10 1280 x 960

79.976 75.025

60.00 60.00

SXGA 15 1280 x 1024 SXGA 16

1280 x 1024 SXGA 17 1152 x 900 SXGA 18

1280 x 1024

(Interlace)

63.37 60.01

76.97 72.00

61.85 66.00

46.43

86.70

SXGA 19

1280 x 1024 63.79 60.18

XGA 5 1024 x 768 60.31 74.92

VGA 7 640 x 480 43.269 85.00

Page 52

APPENDIX

NOTE : Specifications are subject to change without notice.

ON-SCREEN

DISPLAY

RESOLUTION

H-Freq.

(kHz)

V-Freq.

(Hz)

D-VGA

640 x 480 31.47 59.94

D-480p

720 x 480

(

Progressive

)

31.47 59.88

D-575p

768 x 575

(

Progressive

)

31.25 50.00

D-SVGA

800 x 600 37.879 60.32

D-XGA

1024 x 768 43.363 60.00

ON-SCREEN

DISPLAY

RESOLUTION

H-Freq.

(kHz)

V-Freq.

(Hz)

D-WXGA 1

1366 x 768

48.36

60.00

D-WXGA 4

1360 x 768

56.16

72.00

D-1035i

1920 x 1035

(Interlace)

33.75 60.00

D-1080i/60

1920 x 1080

(

Interlace

)

33.75 60.00

D-1080i/50

1920 x 1080

(Interlace)

28.125 50.00

D-WXGA 2

1360 x 768 47.70

60.00

D-WXGA 3

1376 x 768 48.36

60.00

D-720p

1280 x 720

(

Progressive

)

45.00 60.00

D-WXGA 5

1368 x 768

46.50

50.00

D-SXGA 1

1280 x 1024 63.980

60.020

When a input signal is digital from DVI terminal, refer to chart below.

D-SXGA 2

1280 x 1024

60.276

58.069

Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed.

D-SXGA 3

1280 x 1024

31.650

29.80

1400 x 1050

63.970

60.19

D-SXGA+ 1

D-UXGA 1

1600 x 1200

75.00

60.00

OPTIONAL PARTS

The parts listed below are optionally supplied. When ordering those parts, give the name and Type No. to the sales dealer.

● DVI Board (HDCP Compatible) Type No. : POA-MD18DVI

● 5 BNC Board Type No. : POA-MD16VD1

● Video/Y,C & S-Video Board Type No. : POA-MD03VD2A

● D-Sub 15 Board Type No. : POA-MD04VGA

● Network Board Type No. : POA-MD13NET/POA-MD13NET2

● Dual SDI Board Type No. : POA-MD17SDID

● DVI Board Type No. : POA-MD11DVI

Page 53

APPENDIX

Owner’s Manual (CD-ROM) Quick setup manual AC Power Cord Wireless/Wired Remote Control Transmitter and Batteries Remote Control Cable VGA Cable 6 Types Light-Block Sheet (For option lens) 2 Types Lens Attachment (For option lens) Real Color Manager Pro

Accessories

TECHNICAL SPECIFICATIONS

1.8" TFT Active Matrix type, 3 panels

Multi-media Projector

80.3 lbs (36.5 kg)

22.9" x 10" x 30.9" (581 mm x 252 mm x 783 mm)

1024 x 768 dots

2,359,296 (1024 x 768 x 3 panels)

PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N

Up, Down, Left and Right

800 TV lines

41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)

14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)

Projector Type

Net Weight

Dimensions

(W x H x D)

Panel Resolution Number of Pixels Color System

Scanning Frequency Horizontal Resolution

Operating Temperature Storage Temperature

LCD Panel System

300 watt type x 4

Projection Lamp

0˚ to 5.7˚

Feet Adjustment

Power Source : AA or R06 Type x 2 Operating Range : 16.4’ (5m) / ±30˚ Dimensions : 1.97” x 1.06” x 6.61” (50mm x 27mm x 168mm) Net Weight : 4.6 oz (129 g) (including batteries)

Remote Control Transmitter

480i, 480p, 575i, 575p, 720p, 1035i, 1080i-50 and 1080i-60

High Definition TV Signal

AC 120 V (16 A Max. Ampere), 50 / 60 Hz

(The U.S.A and Canada)

AC 200 ~ 240 V (9.0 A Max. Ampere), 50 / 60 Hz

(Continental Europe and The U.K.)

Voltage and Power Consumption

H-sync. 15 ~ 120 KHz, V-sync. 50 ~ 120 Hz

Motorized Lens Shift

DVI-I Terminal (Digital/Analog), RCA Type (Audio R and L) and DIN 8-pin (Control port)

Input 1 Jacks

BNC Type x 5 (R/Pr, G/Y, B/Pb, H/HV and V), RCA Type (Audio R and L) and DIN 8-pin (Control port)

Input 2 Jacks

BNC Type x 2 (VIDEO/Y, C), RCA Type (Audio R and L) and DIN 4-pin (S-Video)

Input 3 Jacks

Serial port in (DB 9), Serial port out (DB 9), USB port, Audio out (RCA Type R and L) and Wired Remote Jack

Other Jacks

HDB 15-pin Terminal (Analog), RCA Type (Audio R and L) and DIN 8-pin (Control port)

Input 4 Jacks

● Specifications are subject to change without notice.

● LCD panels are manufactured to the highest possible standards. At least 99.99% of the pixels are effective,

however a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels.

● Each projector has its own characteristics. When projecting with several projectors on the same screen or side by side, you may recognize different

white balance and color uniformity on each projector.

Page 54

APPENDIX

Vcc

- Data

+ Data

Ground

1 2 3 4

USB PORT TERMINAL

Pin Configuration

Connect USB port output terminal of computer or peripheral equipment to this terminal with USB port Cable (not supplied).

CONFIGURATIONS OF TERMINALS

HDB 15-PIN TERMINAL (ANALOG)

Connect display output terminal of computer to this terminal with VGA Cable (supplied).

Red Input

Ground (Horiz.sync.)

Green Input

Sense 2

Blue Input

Ground (Red) Ground (Green) Ground (Blue)

6 7 8

+5V Power

Horiz. sync.

Ground (Vert.sync.)

DDC Data

Sense 0

Vert. sync. DDC Clock

14 15

Pin Configuration

DVI-I TERMINAL (DIGITAL/ANALOG)

This terminal accepts only Digital (TMDS) or Analog (RGB) output signal. Connect display output terminal of computer to this terminal with DVI cable (not supplied).

T.M.D.S. Data2–

No Connect

T.M.D.S. Data2+

No Connect

T.M.D.S. Data2 Shield

DDC Clock DDC Data Analog Vert. sync

6 7 8

Pin Configuration

T.M.D.S. Data1–

No Connect

T.M.D.S. Data1+

No Connect

T.M.D.S. Data1 Shield

+5V Power Ground (for +5V) Hot Plug Detect

14 15 16

T.M.D.S. Data0–

No Connect

T.M.D.S. Data0+

No Connect

T.M.D.S. Data0 Shield

T.M.D.S. Clock Shield T.M.D.S. Clock+ T.M.D.S. Clock–

22 23 24

Analog Red Input

Analog Ground (R/G/B)

Analog Green Input

Analog Horiz. sync

Analog Blue Input

-----

RxD

TxD

-----

Ground

-----

1 2 3 4

6 7 8 9 -----

Connect serial port output terminal of computer to this terminal with Serial Cable (not supplied).

Pin Configuration

SERIAL PORT IN/OUT TERMINAL

9 678

12345

6789

Page 55

APPENDIX

DIMENSIONS

Unit : inch (mm)

22.87 (581.0)

10.15 (258.0)

2.36 (60.0)

5.7°

9.90 (251.5)

30.83 (783.0)

17.56 (446.0)

22.87 (581.0)

8.62 (219.0)

9.25 (235.0)

5.18 (131.5)

10.61 (269.5)

22.93 (582.5)

17.56 (446.0)

7.01 (178.0)

8.27 (210.0)

7.01 (178.0)

3.26 (82.8)

1.57 (40.0)

8.27 (210.0)

Screw Holes for Ceiling Mount Screws: 9-M8 Depth: 0.315 (8.0)

4.23 (107.5)

9.72 (247.0)

6.81 (173.0)

14.74 (374.5)

1.38 (35.0)

Page 56

1AA6P1P5138-- (KF6A)

SANYO Electric Co., Ltd

Page 57

- 1 -

LCD PROJECTOR

LENS REPLACEMENT AND INSTALLATION PROCEDURES

CAUTION

When installing or replacing the Projection Lens, refer to this manual. For installation of the lens, use the parts designated in the manual. Do not use the installation manual and Light-Block Sheets in the lens package. Check the following parts supplied to this projector.

NOTES ON LENS INSTALLATION

●

Lens installation and replacement should be made by the qualified service personnel.

●

Be sure to install the lens following this procedure precisely.

●

Do not touch or remove any parts except the lens and related parts. It may result in malfunctions, electrical shock, fire hazard or other accidents.

●

Before installing or replacing the lens, check that the Model No. of the Projection Lens matches to the projector.

●

When moving or setting up the projector, be sure to replace the Lens Cover to protect the surface. And be careful not to hold or subject the lens to strong forces. It may damage the lens, cabinet, or mechanical parts.

●

For details of the lens and installation, contact the sales dealer where you purchased the projector.

● LIGHT-BLOCK SHEETS 6 pcs.

● LENS ATTACHMENT (01) 1 pce.

● LENS ATTACHMENT (02) 1 pce.

This projector applies the Projection Lenses listed below. Use the suitable lens for where the projector is used.

AVAILABLE LENS

Model NO.

LNS-W01 LNS-W01Z

LNS-T01 LNS-T01Z

LNS-T02

LNS-W02 LNS-W02Z

LNS-M01 LNS-M01Z

LNS-S02 LNS-S02Z

Type

Fixed Short Throw Lens

Fixed Long Throw Lens

Long Throw Zoom Lens

Short Throw Zoom Lens I

Semi-Long Throw

Zoom Lens

Standard Zoom Lens II

Zoom

Motor Driven

Fixed Manual

Focus

Fixed

Motor Driven

Manual

Motor Driven

LNS-W03

LNS-S03

Short Throw Zoom Lens II

Standard Zoom Lens III

Fixed Manual

Motor Driven Motor Driven

LNS-W04 Wide Zoom Lens Motor Driven Motor Driven

LNS-W06 Wide Zoom Lens Motor Driven Motor Driven

LNS-T03 Long Throw Zoom Lens Manual Manual

Page 58

- 2 -

NOTE : The installation procedure and needed parts

for lens installation depend on the type of the

Projection Lens. Check the Model No. of the

Projection Lens and be sure to install or replace the

lens following procedure below.

Remove Lens Cover. Remove 2 Screws A. Push

part B and pull Upper Lens Cover up.

(See Fig. 1.)

Remove 4 Screws C. Pull Lower Lens Cover

toward front and remove. (See Fig. 2.)

Remove 2 Screws D and Cover Plate on the

back of Upper Lens Cover. (See Fig. 3.)

LENS REPLACEMENT AND INSTALLATION PROCEDURE

Fig-1

UPPER LENS

COVER

Fig-2

LOWER LENS

COVER

COVER PLATE

UPPER LENS

COVER

Fig-3

Page 59

- 3 -

LENS LOCK SCREW

DRIVER IN THE LENS

LOCATE MOTOR

ON RIGHT SIDE

LENS ATTACHMENT

Part No. (610 275 6029)

CONNECTOR

Fig-4

LENS MOTOR LEAD

Fig-6

Fig-5

Fig-7

LENS LOCK

LEVER

LENS

ATTACHMENT

SOCKET

Lens attachments For each lens.

LNS-W01, LNS-W01Z, LNS-W02Z, LNS-W03, LNS-T01, LNS-T01Z, LNS-T02, LNS-T03, LNS-S02, LNS-S02Z, LNS-S03, LNS-M01Z, LNS-W04, LNS-W06

Lens Attachment 01

POA-LNA-01

(610 303 8742)

LNS-W02, LNS-M01

Lens Attachment 02

POA-LNA-02

(610 304 6228)

Lens Model No.

LENS ATTACHMENT

TYPE No. (PART No.)

LENS LOCK RELEASE

LENS LOCK

Remove Lens Cap on the rear (mounting side) of Projection Lens and mount Lens on the lens

Attachment with 4 Screws. (Use screws attached on lens.)

Grasp (release lock) the Lens Lock Lever and turn it fully upward. (See Fig. 6.)

Install the Lens into the projector. Grasp the Lens Lock Lever and turn the Lever fully downward until lever is Locked (clicked position) properly. (See Fig. 7.) When installing the Motor Driven Lens, be sure to mount Lens Motor on right side. (See Fig. 4.) After installing the lens, make sure the Lens is not loose and properly installed.

Connect the Lens Motor Lead connector to the socket on the right-top of the lens attachment. (Motor Driven Lens only.) See Fig. 5.

Grasp (unlock) Lens Lock Lever and pulling upward.

Grasp (unlock) Lens Lock Lever and fully pulled downward until it is locked (clicked).

Page 60

- 4 -

This projector has 6 Light-Block Sheets. Use 2 Light-Block Sheets corresponding with lens. (Refer to the list

below.) Use 1 Light-block Sheet for MODEL LNS-W03

Set 2 Light-Block Sheets through the lens.

Make sure the shape of the Light-Block Sheets are correct and be sure to set them as shown in the Fig. 8.

NOTE:

●

Be sure to set each Light-Block Sheet as shown in Fig-8.

●

Make sure the mark (TOP and BACK) on Light-Block Sheets are correct and set them properly.

Light-Block Sheets For each lens.

Fig-8

LIGHT BLOCK SHEETS

Make sure the sheet figures are

correct and put in proper position.

LIGHT BLOCK SHEET

Make sure the sheet figure is

correct and put in proper position.

MODEL LNS-W03

Lens Model No.

LNS-S02, LNS-S02Z

LNS-M01, LNS-T02, LNS-W02 LNS-M01Z, LNS-W02Z

LNS-W01, LNS-T01, LNS-W01Z LNS-T01Z, LNS-S03, LNS-W04 LNS-W06

Type No. (Part No.)

TYPE FA1 (610 322 7559)

TYPE FA2 (610 322 7894)

TYPE FB1 (610 322 7719)

TYPE FB2 (610 322 7351)

TYPE FC1 (610 322 8136)

TYPE FC2 (610 322 4329)

LNS-W03

TYPE FB1 (610 322 7719)

Page 61

- 5 -

Adjust focus of the Projection Lens. (LNS-W01, LNS-W01Z, LNS-T01, LNS-T01Z and LNS-W03 only.)

Set up the projector and project image on the screen. Loosen Focus Lens Lock Screw and rotate

Projection Lens to obtain proper focus. After adjusting focus, be sure to lock Projection Lens with Focus

Lens Lock Screw securely. (See Fig. 4.) Adjust focus of Projection Lens MODEL LNS-W03, following

Focus Adjustment on page 6.

Replace Lower Lens Cover. Slide Light-Block Sheets into the guide of Lower Lens Cover and set them

in front of the flap. (See Fig. 9.) Fix Lower Lens Cover with 4 Screws C. (See Fig. 2.)

Replace Upper Lens Cover. Slide Light-Block Sheets into the guide of Upper Lens Cover and set them

in front of the flap. (See Fig. 9.) Fix Upper Lens Cover with 2 Screws A. (See Fig. 1.)

Turn the projector on and operate Lens shift, Zoom and Focus fully to check Light-Block Sheets.

If Light-Block Sheets interfere with those operations, check Light-Block Sheets are set properly.

Fig-9

LOWER LENS

COVER

UPPER LENS

COVER

LIGHT-BLOCK

SHEETS

FLAP

Slide into front

of the flap.

Slide into front

of the flap.

FLAP

Slide both upper sides of LIGHT BLOCK

Sheets in between and

CABINET

GUIDE

Page 62

- 6 -

Focus Lock Screw

Focus Lock Ring

● mark (yellow)

FOCUS ADJUSTMENT (For Model LNS-W03)

Set up the projector and project image on the screen.

1. Loosen the Focus Lock Screw on the projection lens.

2. Rotate the projection lens to obtain proper focus on center area of the screen.

When the distance of the screen and lens is 1 meter, set

● mark (yellow) of the lens on Focus Lock Screw

position.

3. Lock the Focus Lock Screw securely.

When proper focus is not observed at outer area of the screen, proceed following adjustments.

4. Loosen the Focus Lock Ring on the projection lens. (Turn the Lock Ring counter-clockwise.)

5. Rotate the lens to obtain proper focus on outer area of the screen.

6. Lock the Focus Lock Ring securely. (Turn the Lock Ring to clockwise.)

If proper focus is not observed over the entire screen, repeat above adjustments 1~ 6.

Page 63

- 7 -

BE SURE TO CHECK FOR SAFETY

After installing or replacing the lens, be sure to check the following for safety.

1. Check the lens is securely fixed with the screws.

2. Check no wiring is damaged or tangled on the gear of the lens motor or

the other mechanical parts.

3. Check no part is missing, and no mounting part is loose.

Some parts are not used for installation or replacement. Keep these parts for later use.

NOTE: Figures in this manual may differ from the actual product.

When the lens is attached to the projector and images are being projected onto the screen, the peripheral focus may be out of focus in some localized areas. If this happens, insert the accessory in between the lens attachment and the lens to correct the focus.

Correcting the focus

Spacer “1” Color; Clear Thickness; 0.1 mm

60-inch projection

Screen

Inserting the spacers corrects the distance for best diagonal focus at the screen. The corrected distance is determined by the thickness of the spacers that are used. As a guide, the distance is adjusted by approximately 30 mm for each 0.1-mm thickness of the spacers. There are three types of spacers provided, and there are four of each spacer type. Use these spacers to correct the distance as required.

C’

D’

A’

B’

Distance

Lens

Lens attachment

Spacer “2” Color; Black Thickness; 0.2 mm

Spacer “3” Color; Cream Thickness; 0.3 mm

Correction distance 30 mm/for 60-inch projection

Correction distance 60 mm/for 60-inch projection

Correction distance 90 mm/for 60-inch projection

Page 64

- 8 -

NOTE: Following table shows approximate measurement. Actual measurement depends on lens and projectors.

SPECIFICATIONS (Throw distance and screen size, screen of lens shift. )

LENS SHIFT (UP/DOWN)

LENS SHIFT (SIDE TO SIDE)

Right max

Upper max

Down max

Left max

LNS-S02

LNS-S02Z

100

120

150 180 200 250 300 350 400 500 600

H1 H2

LNS-W02

LNS-W02Z

LNS-T02

LNS-M01

LNS-M01Z

LNS-S03

LNS-W01

LNS-W01Z

LNS-T01

LNS-T01Z

1.9

1.5

1.4

1.1

5.1

3.8

3.6

2.9

------

3.0

2.4

2.1

1.7

7.5

5.5

5.4

4.3

------

4.1

3.2

2.9

2.3

10.0

7.3

7.2

5.7

------

5.2

4.0

3.6

2.8

12.5

9.1

9.0

7.1

5.3

6.3

4.9

4.4

3.4

14.9

10.8

8.5

6.3

8.0

6.1

5.5

4.3

18.6

13.5

10.5

10.7

8.0

9.6

7.4

6.7

5.2

22.3

16.1

16.2

12.6

12.9

9.6

10.7

8.2

7.4

5.7

24.8

17.9

18.0

14.0

14.3

10.6

13.4

10.4

9.3

7.2

31.0

22.3

22.5

17.5

18.0

13.3

16.2

12.5

11.2

8.6

37.2

26.7

27.0

21.0

21.6

16.0

18.9

14.6

13.1

10.1

43.3

31.1

31.5

24.4

25.2

18.7

21.6

16.7

15.0

11.5

49.5

35.5

36.0

27.9

28.8

21.4

27.1

20.9

18.7

14.4

61.8

44.3

45.0

34.8

36.1

26.8

32.6

25.1

22.5

17.3

74.2

53.1

54.0

41.8

43.4

32.2

0.9

5.6

1.4

8.4

1.9

11.2

2.4

14.0

2.9

16.8

3.6

21.0

4.4

25.3

4.9

28.1

6.1

35.1

7.4

42.1

8.6

49.2

9.8

56.2

12.3

70.3

14.8

84.3

W1 W2

0 10

1 8 4 6

1 8

1 8 4 6

1 8

1 8 4 6

LNS-W03

7.5

11.1

14.8

0.6

0.9 1.3

1.6

1.9

2.4

2.9

3.3

4.1

4.9

5.8

6.6

8.3

9.9

5.3

7.8

10.2

12.7

18.4

15.1

22.0

18.8

27.4

22.5

32.8

25.0

36.4

31.1

45.5

37.3

54.5

43.4

63.5

49.6

72.6

61.9

90.6

74.2

108.7

LNS-T03

LNS-W04

LNS-W06

------

2.4

1.8

1.4

3.2

2.5

2.4

1.9

4.0

3.1

3.0

2.4

4.9

3.8

3.7

2.9

6.1

4.7

4.6

3.6

7.4

5.7

5.6

4.4

8.2

6.3

6.2

4.9

10.3

7.9

7.8

6.1

12.4

9.5

9.4

7.3

14.5

11.2

11.0

8.5

16.6

12.8

12.5

9.7

20.8

16.0

15.7

12.2

------

19.2

------

14.6

1 8

Model No.

Zoom

MIN

MAX

NONE

U/D (MAX)

SIDE (MAX)

SCREEN SIZE (INCH) AND THROW DISTANCE (m)

LENS SHIFT/

CENTER RATIO

MIN

MAX

MIN

MAX

MIN

MAX

MIN

MAX

MIN

MAX

MIN

MAX

MIN

MAX

NONE

W2W1

W2 W1

Sanyo PLC-XF46N-E User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

TO THE OWNER

SAFETY INSTRUCTIONS

COMPLIANCES

TABLE OF CONTENTS

FEATURES AND DESIGN

PREPARATION

NAME OF EACH PART OF PROJECTOR

SETTING-UP PROJECTOR

CONNECTING AC POWER CORD

POSITIONING PROJECTOR

LENS INSTALLATION

LENS SHIFT ADJUSTMENT

PICTURE LEVEL AND TILT ADJUSTMENT

INSTALLING PROJECTOR IN PROPER POSITION

MOVING PROJECTOR

CONNECTING PROJECTOR

TERMINALS OF PROJECTOR

CONNECTING TO COMPUTER

BEFORE OPERATION

SIDE CONTROLS AND INDICATORS

OPERATION OF REMOTE CONTROL

REMOTE CONTROL BATTERIES INSTALLATION

HOW TO OPERATE ON-SCREEN MENU

FLOW OF ON-SCREEN MENU OPERATION

OPERATING ON-SCREEN MENU

MENU BAR

BASIC OPERATION

TURNING ON PROJECTOR

TURNING OFF PROJECTOR

TURNING ON / OFF PROJECTOR

KEYSTONE ADJUSTMENT

ADJUSTING SCREEN

ZOOM ADJUSTMENT

FOCUS ADJUSTMENT

LENS SHIFT ADJUSTMENT

PICTURE FREEZE FUNCTION

NO SHOW FUNCTION

P-TIMER FUNCTION

COMPUTER INPUT

SELECTING COMPUTER SYSTEM

SELECTING INPUT SOURCE

PC ADJUSTMENT

AUTO PC ADJUSTMENT

MANUAL PC ADJUSTMENT

PICTURE IMAGE ADJUSTMENT

IMAGE LEVEL ADJUSTMENT

PICTURE SCREEN ADJUSTMENT

VIDEO INPUT

SELECTING INPUT SOURCE

SELECTING VIDEO SYSTEM

PICTURE IMAGE ADJUSTMENT

IMAGE LEVEL ADJUSTMENT

PICTURE SCREEN ADJUSTMENT

SETTING

SETTING MENU

APPENDIX

AIR FILTER CARE AND CLEANING

MAINTENANCE

WARNING TEMP. INDICATOR

LAMP MANAGEMENT

LAMP REPLACEMENT

LAMP REPLACE COUNTER

TROUBLESHOOTING

MENU TREE

INDICATORS AND PROJECTOR CONDITION

COMPATIBLE COMPUTER SPECIFICATIONS

TECHNICAL SPECIFICATIONS

CONFIGURATIONS OF TERMINALS

DIMENSIONS

LCD PROJECTOR