Sanyo PLC-XF10N, PLC-XF10NL User Manual

Multimedia Projector

MODEL PLC-XF10N

MOD PLC-XF10NL

(

Without Lens

)

Owner's
Manual

2

WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This Projector has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the
power outlet. Do not try to defeat this safety feature.

Intense light source. Do not stare directly into the projection lens as possible eye damage could result.
Be especially careful that children do not stare directly into the beam.

The Remote Control Unit, supplied to this projector, emits the laser beam as the Laser Pointer function from the
Laser Light Window while pressing the LASER button. Do not look into the Laser Light Window or shine the laser
beam on yourself or other people. Eye damage may result.

If the Projector will not be used for an extended time, unplug the new Projector from the power outlet.
This Projector should be set in the way indicated. Never hang the projector, or fall down on its side.

It may result in fire hazard.

READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.

As the owner of a new Multi-media Projector, you are probably eager to try out your new projector. Before you do, we suggest
that you spend a little time reading this manual to familiarize yourself with the operating procedures, so that you will receive
maximum satisfaction from the many features included in your new projector.
This owner's manual will acquaint you with your projector's features. Reading it will help us too. Through the years, we have
found that many service requests were not caused by problems with our projectors. They were caused by problems that
could have been prevented, if the owner had followed the instructions in the manual.
You can often correct operating problems yourself. If your projector fails to work properly, see "TROUBLESHOOTING"
section on pages 55 ~ 56 and try the solutions marked for each problem.

SAFETY PRECAUTIONS

TO THE OWNER

INFORMATION TO THE USER

NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the owner's manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE CONSTITUTING
A RISK OF ELECTRIC SHOCK IS
PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE
OWNER'S MANUAL WITH THIS UNIT.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

PROJECTOR

(FRONT)

PROJECTOR

(SIDE)

WALL

50cm

50cm

50cm50cm

Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:

a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the

operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified technician
to restore the projector to normal operation.

e. If the projector has been dropped or the cabinet has been

damaged.

f. When the projector exhibits a distinct change in

performance-this indicates a need for service.

When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.

Upon completion of any service or repairs to this projector,
ask the service technician to perform routine safety checks
to determine that the projector is in safe operating condition.

This projector is equipped with a
grounding type AC line plug.
Should you be unable to insert the
plug into the outlet, contact your
electrician. Do not defeat the safety
purpose of this grounding type plug.

Follow all warnings and instructions marked on the
projectors.

For added protection to the projector during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will
prevent damage due to lightning and powerline surges.

An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance
and cart combination to overturn.

If the projector is to be built into a compartment or similarly
enclosed, the minimum distances must be maintained.

Do not cover the ventilation slot on the projector.
Heat build-up can reduce the service life of your projector,

and can also be dangerous.

3

IMPORTANT SAFETY INSTRUCTIONS

All the safety and operating instructions should be read
before the product is operated.

Read all of the instructions given here and retain them for
later use. Unplug this projector from AC power supply
before cleaning. Do not use liquid or aerosol cleaners. Use
a damp cloth for cleaning.

Do not use attachments not recommended by the
manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or
table. The projector may fall, causing serious injury to a
child or adult, and serious damage to the projector. Use
only with a cart or stand recommended by the
manufacturer, or sold with the projector. Wall or shelf
mounting should follow the manufacturer's instructions,
and should use a mounting kit approved by the
manufacturer.

Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...

Slots and openings in the back and bottom of the cabinet
are provided for ventilation, to insure reliable operation of
the equipment and to protect it from overheating.

The openings should never be covered with cloth or other
material, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or
over a radiator or heat register.

This projector should not be placed in a built-in installation
such as a bookcase unless proper ventilation is provided.

This projector should be operated only from the type of
power source indicated on the marking label. If you are not
sure of the type of power supplied, consult your authorized
dealer or local power company.

Do not overload wall outlets and extension cords as this
can result in fire or electric shock. Do not allow anything to
rest on the power cord. Do not locate this projector where
the cord will be abused by persons walking on it.

Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points
or short out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the projector.

Do not attempt to service this projector yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.

GROUND

4

TABLE OF CONTENTS

PAGE

PAGE

FEATURES AND DESIGN 5

INTRODUCTION 5
COMPATIBILITY 5

IMAGE RESOLUTION 5
AUTOMATIC MULTISCANNING SYSTEM 5

SCREEN MODE 5
MULTILANGUAGE 5
UNPACKING THE PROJECTOR 5
TRADEMARKS 5

INSTALLATION 6-9

NAME OF EACH PART OF THE PROJECTOR 6
SETTING-UP THE PROJECTOR 7
MOVING THE PROJECTOR 8
POWER REQUIREMENTS 9

CONNECTING THE PROJECTOR 10-21

TERMINAL OF THE PROJECTOR 10-11
CONNECTING THE COMPUTER 12-19
CONNECTING THE VIDEO EQUIPMENT 20-21

BEFORE OPERATION 22-31

CONTROLS AND INDICATOR 22-23
OPERATION OF THE REMOTE CONTROL 24-28

WIRELESS REMOTE CONTROL UNIT 24-26
WIRELESS REMOTE CONTROL UNIT 27-28

CONTROL THE PROJECTOR 29-31

DIRECT OPERATION 29
MENU OPERATION 30-31

BASIC OPERATION 32-51

TURNING ON/OFF THE PROJECTOR 32
DIRECT OPERATION 33-34

MODE SELECT 33
SOUND VOLUME ADJUSTMENT 33
SOUND MUTE FUNCTION 33
ZOOM ADJUSTMENT 33
FOCUS ADJUSTMENT 33
LENS SHIFT ADJUSTMENT 33
DIGITAL ZOOM FUNCTION 34
NORMAL PICTURE FUNCTION 34
FREEZE PICTURE FUNCTION 34
NO SHOW FUNCTION 34

P-TIMER FUNCTION 34
AUTO IMAGE FUNCTION 34
CURSOR FUNCTION 34

MENU OPERATION 35-36

MODE SELECT 35
SOUND ADJUSTMENT 36
LANGUAGE ADJUSTMENT 36

VIDEO MODE 37-39

COLOR SYSTEM SELECT 37
VIDEO SOURCE SELECT 37
PICTURE IMAGE ADJUSTMENT 38
PICTURE SCREEN ADJUSTMENT 39

COMPUTER MODE 40-49

COMPUTER SYSTEM SELECT 40
COMPATIBLE COMPUTER SPECIFICATIONS 41
AUTO IMAGE FUNCTION 42
PICTURE IMAGE ADJUSTMENT 43
PICTURE POSITION ADJUSTMENT 44
PC ADJUSTMENT 45-48
PICTURE SCREEN ADJUSTMENT 49

OTHER FUNCTION SETTING 50-52

BLUE BACK 50-51
DISPLAY 50-51
REVERSE T/B 50-51
REVERSE L/R 50-51
SPLIT WIPE 50-51
POWER MANAGEMENT 50-51
USB (Mouse or Control) 50-51
REMOTE CONTROL (Mode 1 or Mode 2) 50-51
LAMP AGE 52

APPENDIX 53-57

MAINTENANCE 53-55

TEMPERATURE WARNING INDICATOR 53
AIR FILTER CARE AND CLEANING 53
LAMP REPLACEMENT 54
CLEANING THE LENS 55

TROUBLESHOOTING 55-56
TECHNICAL SPECIFICATIONS 57

The multimedia projector that combines powerful and sophisticated features with easy-to-use, intuitive controls. Built-in
multimedia features include audio, a palette of 16.77 million colors and active matrix liquid crystal display (LCD) technology.
The projector is ideal for high-performance business, training and imaging applications that demand exceptional color
quality.

The projector is compatible with many different types of personal computers and video devices, including:

● IBM-compatible computers, including laptops, up to 1280 x 1024 resolution.

● Apple Macintosh and PowerBook computers up to 1280 x 1024 resolution.

● Various VCRs, video disc players, video cameras, DVD players, satellite TV tuners or other AV equipment using any of the

worldwide video standards, including NTSC, NTSC4.43, PAL, PAL-M, PAL-N and SECAM.

The resolution of the projector's projected image is 1024 x 768. The projector displays computer images just as they appear
on your computer's monitor. Screen resolutions between 1024 x 768 and 1280 x 1024 are compressed to 1024 x 768. The
projector cannot display screen resolutions above 1280 x 1024. If your computer's screen resolution is higher than 1280 x
1024, reset it to a lower resolution before you connect the projector.

This projector can detect display signals from most personal computers currently distributed. It is free from complicated
adjustments to project picture images from PC.

Screen display can be selected among;

Computer mode --- True, Digital zoom (Expand, Compress, Panning)
Video mode --- Regular (4:3), Wide (16:9)

MENU DISPLAY is displayed with; English, German, French, Italian, Spanish and Japanese.

The projector comes with the parts listed below. Check to find all the parts are included. If any parts are missing, contact an
authorized dealer or service station.

● Owner's Manual. ● AC Power Cord.

● Wireless Remote Control Unit. ● Wireless/Wired Remote Control Unit.

● Remote Control Cable. ● Batteries for Remote Control Units.

● VGA Cable. ● Mouse Cable for PS/2 port.

● Mouse Cable for serial port. ● Mouse Cable for ADB port.

● VGA/MAC Adapter. ● Protective Dust Cover

● Lens Cover.

● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc.

● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.

● Windows is a trademarks or registered trademarks of Microsoft Corporation.

● Other trademarks are the property of their respective owners.

5

FEATURES AND DESIGN

INTRODUCTION

COMPATIBILITY

IMAGE RESOLUTION

UNPACKING THE PROJECTOR

TRADEMARKS

SCREEN MODE

AUTOMATIC MULTISCANNING SYSTEM

MULTILANGUAGE

6

EXHAUST VENT

CAUTION HOT AIR!
Air blown from the exhaust vent is hot.
Observe the following when handling your

projector or choosing a location to install it.

● Keep heat-sensitive objects away from the
exhaust port.

● If you set the projector on top of a metallic
surface, the surface will become hot because of
the hot air exhaust. Be careful when handling.

● Do not touch the cabinet near to the exhaust
vent area, and especially screws and metallic
parts. These parts will become hot while the
projector is used.

FRONT OF THE PROJECTOR

REAR OF THE PROJECTOR

SPEAKER

INFRARED
REMOTE
RECEIVER

PROJECTION LENS

REMOVABLE
LENS COVER

INFRARED
REMOTE
RECEIVER

MAIN ON/OFF
SWITCH

CARRY
HANDLE

POWER CORD
CONNECTOR

ADJUSTABLE
FEET

AIR INTAKE VENT

BOTTOM OF THE PROJECTOR

AIR INTAKE
VENT

LAMP
COVER

NAME OF EACH PART OF THE PROJECTOR

INSTALLATION

200"
154"

26.9' (8.2 m)

600"
462"

80.7' (24.6 m)

7

40"

77"

115"

154"

231"

308"

462"

600"

100"

150"

200"

300"

400"

760 mm 760 mm

100"
SCREEN

POSITIONING:

ROOM LIGHT

● This projector is basically designed to project on a flat projection surface.

● This projector can be focused from 4.9' (1.5 m) ~ 80.7' (24.6 m).

● Refer to the figure below as an example when positioning the projector to the screen.

The projector should be placed in a room with
limited light. Picture quality will be directly
affected by lightning conditions.

Minimum Zoom

Maximum Zoom

DISTANCE

Screen
Size

Max. Zoom
Min. Zoom

Distance

40"

4.9' (1.5 m)

100"

77"

13.1' (4.0 m)

150"
115"

20' (6.1 m)

300"
231"

40' (12.2 m)

400"
308"

53.8' (16.4 m)

THIS PROJECTOR SHOULD BE SET IN THE WAY INDICATED. NEVER HANG
THE PROJECTOR, OR FALL DOWN ON ITS SIDE. IT MAY RESULT IN FIRE
HAZARD.

Picture tilt and projection angle can be adjusted by twisting
ADJUSTABLE FEET. Projection angle can be adjusted up
to 4 degrees by rotating Adjustable Feet.

MOVE THE PROJECTED IMAGE POSITION
Adjust the projected image position (maximum 760mm

downward or upward on the 100" screen) by using lens shift
function. (See page 33.)

UP

UP

DOWN

DOWN

ADJUSTABLE FEET

ADJUSTABLE FEET

SETTING-UP THE PROJECTOR

INSTALLATION

8

Use the carry handle when moving the projector.
Replace the lens cover and rotate the adjustable feet fully
clockwise.

CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR

● Do not drop or give a shock to the projector, otherwise damage or malfunction may result.

● When carrying the projector, use a Sanyo recommended Carrying Case.

● Do not transport the projector by using a courier or transport service in an unsuitable transport case. This may cause

damage to the projector. To transport the projector through a courier or transport service, use a Sanyo recommended
Case.

● For a carrying or transportation cases, contact a Sanyo authorized dealer.

This projector is equipped with a cooling fan to protect it from
overheating. Pay attention to the following to ensure the ventilation
and avoid a possible risk of fire and malfunction.

● Do not cover the vents with papers or other materials.

●

Keep the rear grill at least 3.3' (1m) away from any object.

● Make sure that there are no objects under the projector.
An object under the projector may prevent the projector
from taking the cooling air through the bottom vent.

VENTILATION

AIR INTAKE VENT
(BOTTOM SIDE)

EXHAUST VENT
(REAR SIDE)

MOVING THE PROJECTOR

INSTALLATION

9

Your projector uses nominal input voltages of 100-120 VAC. The projector
automatically selects the correct input voltage. The projector is designed to work
with single-phase power systems having a grounded neutral conductor. To reduce
the risk of electrical shock, do not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure what type of
power is supplied to your building.

Connect the AC power supply cord
(supplied) to the projector.
The socket-outlet must be near this
equipment and must be easily
accessible.

INSTALLATION

POWER REQUIREMENTS

Projector side (Female)

AC outlet side (Male)

10

SIDE OF THE PROJECTOR (CONNECT THE COMPUTER)

COMPUTER INPUT-1 TERMINAL (ANALOG HDB 15-PIN)

Used to connect a computer to the projector.

COMPUTER INPUT-1 TERMINAL (DIGITAL MDR 20-PIN)

Used to connect a computer to the projector.

COMPUTER INPUT-2 JACKS (BNC TYPE x 5)

Used to connect a computer to the projector.

MONITOR OUTPUT TERMINAL (ANALOG HDB 15-PIN)

Used to connect a monitor to the projector.

COMPUTER AUDIO INPUT-1 JACKS (R and L)

Used to connect an audio output from the computer to the
projector.

COMPUTER AUDIO INPUT-2 JACKS (R and L)

Used to connect an audio output from the computer to the
projector.

AUDIO MONITOR OUTPUT JACKS (R and L)

Used to connect an audio input from audio equipment to the
projector.

CONTROL PORT-1 CONNECTOR

Used to connect a mouse cable to the projector.

CONTROL PORT-2 CONNECTOR

Used to connect a mouse cable to the projector.

USB PORT-1 CONNECTOR

Used to connect a computer to the projector.

USB PORT-2 CONNECTOR

Used to connect a computer to the projector.

SERIAL PORT TERMINAL (DB9)

Used to connect a computer to the projector.

WIRED REMOTE JACK

When using the wired remote control, connect the
remote cable to this jack.

USB 1 AUDIO 1

R

ANALOG

ANALOG RGB

COMPUTER OUT

COMPUTER IN-2 COMPUTER IN-1

RGB H V

L

(MONO)

(MONO)

CONTROL PORT 1

USB 2

R/C JACK SERIAL PORT

AUDIO 2

AUDIO OUT

RL

RL

CONTROL PORT 2

DIGITAL

10

1

13

11

2

3

4

7

6 5

9

8

12

1
2

3
4
5

6

8
9

10
11

12
13

7

CONNECTING THE PROJECTOR

TERMINAL OF THE PROJECTOR

11

VIDEO/Y C/Cb(B-Y) Cr(R-Y) S-VIDEO

RL

(MONO)

AUDIO

VIDEO/Y C/Cb(B-Y) Cr(R-Y) S-VIDEO

RL

(MONO)

AUDIO

VIDEO/Y C/Cb(B-Y) Cr(R-Y) S-VIDEO

RL

AUDIO

VIDEO IN-1VIDEO IN-2MONITOR OUT

14

17

20

15

18

19

21

22

16

SIDE OF THE PROJECTOR (CONNECT THE VIDEO EQUIPMENT)

VIDEO INPUT JACKS-1 (BNC TYPE x 3)

Used to connect a video source to the projector.

S-VIDEO INPUT JACK-1

Used to connect a S-VHS video source to the projector.

AUDIO INPUT JACKS-1 (R and L)

Used to connect an audio source to the projector.

VIDEO INPUT JACKS-2 (BNC TYPE x 3)

Used to connect a video source to the projector.

S-VIDEO INPUT JACK-2

Used to connect a S-VHS video source to the projector.

14
15
16

17
18

AUDIO INPUT JACKS-2 (R and L)

Used to connect an audio source to the projector.

VIDEO MONITOR OUTPUT JACKS (BNC TYPE x 3)

Permits video connection to a monitor.

VIDEO MONITOR (S-VIDEO) OUTPUT JACK

Permits S-VHS video connection to a monitor.

AUDIO MONITOR OUTPUT JACKS (R and L)

Permits audio connection to a monitor.

19
20
21

22

CONNECTING THE PROJECTOR

––––––––

ADB
––––––––
––––––––
––––––––
––––––––
––––––––
––––––––

GND
––––––––
––––––––
––––––––

Serial Port

ADB Port

1
2
3
4
5
6
7
8

9
10
11
12

PS/2 Port

T x D
––––––––
––––––––
––––––––
––––––––
––––––––

READY

––––––––

GND
––––––––
––––––––
––––––––

––––––––

CLK

DATA
––––––––
––––––––
––––––––
––––––––
––––––––

GND
––––––––
––––––––
––––––––

12

CONNECTING THE COMPUTER

CONNECTING THE PROJECTOR

Personal computers can be connected to the HDB15-pin (VGA) terminal on the projector.

● Connect the computer to these terminals using the VGA cable and VGA/MAC adapter (provided).
CAUTION: For projectors, the VGA cable provided is designed to reduce RFI (Radio Frequency Interference) emissions.

For regulatory compliance reasons, this cable must be used and must not be replaced by any other cable.

Digital output signal from the computer can be connected to the DIGITAL terminal (MDR 20-pin). When using this input,
Graphic Accelerator Board designed for this projector should be installed into your computer and set-up the computer
configuration following instruction included in the Graphic Accelerator Board package. Refer to DIGITAL INPUT
CONNECTION on page 15 and 17.

Personal computers can be connected to the computer input (Red, Green, Blue, Horiz. Sync. and Vert. Sync.) on the
projector.

● Connect the computer to these jacks using the BNC cables (not provided).

● Connect audio outputs from your computer to these jacks using the audio cable (not provided).

● When the computer is operated by projector's remote control unit, connect three different type of cables (provided)

between projector control port and computer mouse port or serial port.

■ CONTROL PORT

AA

B

CONTROL PORT CABLE REMOVAL
HINT

Disconnect control port cable with
following steps.

1. Hold the portion (A)
of the connector
with one hand.

2. Pull the portion (B)
arrow direction and
remove connector.

CONNECTING TO THE COMPUTER INPUT 1 TERMINAL (ANALOG HDB 15-PIN)

CONNECTING TO THE COMPUTER INPUT 1 TERMINAL (DIGITAL MDR 20-PIN)

CONNECTING TO THE COMPUTER INPUT 2 JACKS (BNC x 5)

CONNECTING TO THE COMPUTER AUDIO INPUT JACKS (1 and 2)

CONNECTING TO THE MULTI-POLE 12-PIN (CONTROL PORT) CONNECTORS (1 and 2)

COMPUTER TYPE

IBM Compatible computer with PS/2 mouse port.
IBM Compatible computer with serial port.
Apple Macintosh computer with ADB mouse port.

CABLE

Mouse Cable for PS/2 port.
Mouse Cable for Serial port.
Mouse Cable for ADB port.

2

5

6

10

9

12

1

4

3

7

8

11

These jacks will contain the audio information of the selected program source being viewed on the screen (Computer 1,
Computer 2, Video 1 or Video 2). If you have selected program source Computer 2 the audio signal connected to the
Computer 2 audio input jack will be available at the audio monitor output jacks.
Use RCA type audio for connection.

● If the audio input of the audio equipment is stereo, be sure to connect the right and left channels to the respective right
and left jacks.

● If the audio input of the audio equipment is monaural, connect it to the left jack.

Vcc

- Data

+ Data

Ground

1
2
3
4

This terminal output the information of the selected computer source being viewed on the screen (Computer 1 or Computer 2).
When video source ("Video 1" or "Video 2") is selected, this terminal outputs Computer 1 input information.

An external monitor can be connected to the HDB15-pin (VGA) terminal on the projector.

● Connect the monitor to this terminal using the VGA cable (not provided).

13

––––––––

R x D
T x D

––––––––

Ground
––––––––
––––––––
––––––––
––––––––

1
2
3
4
5
6
7
8
9

■ SERIAL PORT
DB9-PIN

TERMINAL

■ USB PORT

Pin No./Signal

1 Red input
2 Green input
3 Blue input
4 Sense 2
5 Ground (Horiz.sync.)
6 Ground (Red)
7 Ground (Green)
8 Ground (Blue)

Pin No./Signal

9 Non Connect
10 Ground (Vert. sync.)
11 Sense 0
12 Sense 1
13 Horiz. sync
14 Vert. sync
15 Reserved

HDB 15-PIN
TERMINAL

CONNECTING THE PROJECTOR

CONNECTING TO THE MONITOR OUTPUT TERMINAL (ANALOG HDB 15-PIN)

CONNECTING TO THE AUDIO MONITOR OUTPUT (VARIABLE) JACKS

CONNECTING TO THE SERIAL PORT (DB 9-PIN) TERMINAL

CONNECTING TO THE USB PORT CONNECTORS (1 and 2)

● If you control the projector by computer, you must connect a cable (not provided)
from your computer to this terminal.

This Projector is designed for connecting with USB Port of the computer or peripheral
equipment that is to be standard.

54321

109876

15 14 13 12 11

12345

6789

2

1

34

14

USB 1 AUDIO 1

R

ANALOG

ANALOG RGB

COMPUTER OUT

COMPUTER IN-2 COMPUTER IN-1

RGB H V

L

(MONO)

(MONO)

CONTROL PORT 1

USB 2

R/C JACK SERIAL PORT

AUDIO 2

AUDIO OUT

RL

RL

CONTROL PORT 2

DIGITAL

COMPUTER OUTPUT
(HDB15-PIN TYPE)

COMPUTER

MONITOR CABLE
(NOT PROVIDED)

COMPUTER
OUTPUT
(BNC TYPE x 5)

SERIAL PORT
INPUT

AUDIO CABLE
(NOT PROVIDED)

AUDIO CABLE
(NOT PROVIDED)

COMPUTER
AUDIO INPUT 1 or 2

CONTROL PORT
OUTPUT 1 or 2

MOUSE CABLE FOR
PS/2 PORT
(PROVIDED)

MOUSE CABLE FOR
SERIAL PORT
(PROVIDED)

PS/2 PORT
INPUT

VGA CABLE
(PROVIDED)

L R

R L

Speaker (L)

Speaker (R)

Amp.

L

R

R
L

AUDIO
INPUT

SPEAKER
OUT

MONITOR
OUTPUT

BNC CABLE x 5
(NOT PROVIDED)

COMPUTER
AUDIO OUTPUT

SERIAL PORT CABLE
(NOT PROVIDED)

SERIAL
PORT
OUTPUT

COMPUTER
AUDIO OUTPUT

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be

disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

COMPUTER
INPUT 1
(ANALOG)

CONNECTING THE PROJECTOR

CONNECTING AN IBM-COMPATIBLE DESKTOP COMPUTER

COMPUTER
INPUT 2

15

CONNECTING THE PROJECTOR

USB 1 AUDIO 1

R

ANALOG

ANALOG RGB

COMPUTER OUT

COMPUTER IN-2 COMPUTER IN-1

RGB H V

L

(MONO)

(MONO)

CONTROL PORT 1

USB 2

R/C JACK SERIAL PORT

AUDIO 2

AUDIO OUT

RL

RL

CONTROL PORT 2

DIGITAL

COMPUTER

MONITOR CABLE
(NOT PROVIDED)

SERIAL PORT
INPUT

AUDIO CABLE
(NOT PROVIDED)

AUDIO CABLE
(NOT PROVIDED)

COMPUTER
AUDIO INPUT 1

CONTROL PORT
OUTPUT 1

MOUSE CABLE FOR
PS/2 PORT
(PROVIDED)

MOUSE CABLE FOR
SERIAL PORT
(PROVIDED)

PS/2 PORT
INPUT

L R

R L

Speaker (L)

Speaker (R)

Amp.

L

R

R
L

AUDIO
INPUT

SPEAKER
OUT

COMPUTER
AUDIO OUTPUT

SERIAL PORT CABLE
(NOT PROVIDED)

SERIAL
PORT
OUTPUT

COMPUTER
AUDIO OUTPUT

COMPUTER
INPUT 1
(DIGITAL)

CONNECTING AN IBM-COMPATIBLE DESKTOP COMPUTER

(DIGITAL INPUT CONNECTION)

DIGITAL FLAT
PANEL CABLE
(NOT PROVIDED)

GRAPHIC
ACCELERATOR
BOARD

DIGITAL
OUTPUT

ANALOG
OUTPUT

INSTALL (PLUG)
INTO PCI BUS SLOT

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be

disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

Before using with digital connection, install (Plug in) Graphic Accelerator
Board into PCI bus slot of the computer and set up the computer
following instructions in the Graphic Accelerator Board package.

NOTE: This connection need optionally sold Graphic Accelerator Board.

For this information, contact to your authorized dealer.

16

USB 1 AUDIO 1

R

ANALOG

ANALOG RGB

COMPUTER OUT

COMPUTER IN-2 COMPUTER IN-1

RGB H V

L

(MONO)

(MONO)

CONTROL PORT 1

USB 2

R/C JACK SERIAL PORT

AUDIO 2

AUDIO OUT

RL

RL

CONTROL PORT 2

DIGITAL

SERIAL
PORT
OUTPUT

COMPUTER

COMPUTER OUTPUT
(DB15-PIN TYPE)

SERIAL PORT
INPUT

PS/2 PORT
INPUT

AUDIO CABLE
(NOT PROVIDED)

AUDIO CABLE
(NOT PROVIDED)

VGA CABLE
(PROVIDED)

MOUSE CABLE FOR
PS/2 PORT
(PROVIDED)

MOUSE CABLE FOR
SERIAL PORT
(PROVIDED)

R L

R L

Speaker (L)

Speaker (R)

Amp.

L

R

R

L

AUDIO
INPUT

SPEAKER
OUT

COMPUTER
AUDIO OUTPUT

COMPUTER
AUDIO INPUT 1

CONTROL PORT
OUTPUT 1

COMPUTER
AUDIO OUTPUT

SERIAL PORT CABLE
(NOT PROVIDED)

CONNECTING THE PROJECTOR

CONNECTING AN IBM-COMPATIBLE LAPTOP COMPUTER

COMPUTER
INPUT 1
(ANALOG)

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be

disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

USB 1 AUDIO 1

R

ANALOG

ANALOG RGB

COMPUTER OUT

COMPUTER IN-2 COMPUTER IN-1

RGB H V

L

(MONO)

(MONO)

CONTROL PORT 1

USB 2

R/C JACK SERIAL PORT

AUDIO 2

AUDIO OUT

RL

RL

CONTROL PORT 2

DIGITAL

Before using with digital connection, install (Plug in) Graphic
Accelerator PC card into card bus slot of the computer and set up
the computer following instructions in the Graphic Accelerator PC
card package.

SERIAL
PORT
OUTPUT

COMPUTER

SERIAL PORT
INPUT

PS/2 PORT
INPUT

AUDIO CABLE
(NOT PROVIDED)

AUDIO CABLE
(NOT PROVIDED)

MOUSE CABLE FOR
PS/2 PORT
(PROVIDED)

MOUSE CABLE FOR
SERIAL PORT
(PROVIDED)

R L

R L

Speaker (L)

Speaker (R)

Amp.

L

R

R

L

AUDIO
INPUT

SPEAKER
OUT

COMPUTER
AUDIO OUTPUT

COMPUTER
AUDIO INPUT 1

CONTROL PORT
OUTPUT 1

COMPUTER
AUDIO OUTPUT

SERIAL PORT CABLE
(NOT PROVIDED)

COMPUTER
INPUT 1
(DIGITAL)

DIGITAL FLAT
PANEL CABLE
(NOT PROVIDED)

17

CONNECTING THE PROJECTOR

CONNECTING AN IBM-COMPATIBLE LAPTOP COMPUTER

(DIGITAL INPUT CONNECTION)

GRAPHIC
ACCELERATOR
PC CARD

DIGITAL
OUTPUT

ANALOG
OUTPUT

INSTALL (PLUG)
INTO PC CARD
BUS SLOT

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be

disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

NOTE: This connection need optionally sold Graphic Accelerator PC card.

For this information, contact to your authorized dealer.

USB 1 AUDIO 1

R

ANALOG

ANALOG RGB

COMPUTER OUT

COMPUTER IN-2 COMPUTER IN-1

RGB H V

L

(MONO)

(MONO)

CONTROL PORT 1

USB 2

R/C JACK SERIAL PORT

AUDIO 2

AUDIO OUT

RL

RL

CONTROL PORT 2

DIGITAL

123456

ON

18

CONNECTING THE PROJECTOR

CONTROL PORT
OUTPUT 1 or 2

COMPUTER

MONITOR CABLE
(NOT PROVIDED)

COMPUTER
OUTPUT
(BNC TYPE x 5)

BNC CABLE x 5
(NOT PROVIDED)

COMPUTER
OUTPUT

COMPUTER
AUDIO OUTPUT1 or 2

AUDIO CABLE
(NOT PROVIDED)

AUDIO CABLE
(NOT PROVIDED)

MOUSE CABLE FOR
ADB PORT
(PROVIDED)

COMPUTER
INPUT 2

VGA/MAC ADAPTER
(PROVIDED)

R L

R L

Speaker (L)

Speaker (R)

Amp.

L

R

R

L

AUDIO
INPUT

SPEAKER
OUT

COMPUTER
AUDIO OUTPUT

SERIAL PORT CABLE
(NOT PROVIDED)

SERIAL
PORT
OUTPUT

COMPUTER
INPUT 1
(ANALOG)

CONNECTING A MACINTOSH DESKTOP COMPUTER

VGA CABLE
(PROVIDED)

COMPUTER
AUDIO OUTPUT

MONITOR
OUTPUT

ON

2

34

5

61

ON

OFF

VGA/MAC ADAPTER

SW1 ~ SW6

Set the dip switches as shown in the table below depending on
the RESOLUTION MODE that you want to use before you turn
on the projector and computer.

ADB PORT
INPUT

ADB PORT
INPUT

SW1

ON
OFF
OFF

ON

RESOLUTION MODE
13" MODE (640

x

480)

16" MODE (832

x

624)

19" MODE (1024

x

768)

21" MODE (1152

x

870)

SW6

OFF
OFF
OFF
OFF

SW5
OFF
OFF
OFF
OFF

SW4

OFF

ON

OFF

ON

SW3

OFF
OFF

ON
ON

SW2

ON
ON
ON
ON

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be

disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.