Multimedia Projector
MODEL PLC-SU32
Owner’s Manual
TO THE OWNER
Before operating this projector, read this manual thoroughly and operate the projector properly.
This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time.
Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.
If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the “TROUBLESHOOTING” section at the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the projector or the service center.
SAFETY PRECAUTIONS
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
●This projector produces intense light from the projection lens. Do not stare directly into the lens as possible. Eye damage could result. Be especially careful that children do not stare directly into the beam.
●This projector should be set in the way indicated. If not, it may result in a fire hazard.
● Take appropriate space on the top, sides and rear of the projector |
|
SIDE and TOP |
|
REAR |
|
|||||
cabinet for allowing air circulation and cooling the projector. 20cm |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Minimum distance should be taken. If the projector is to be built |
|
|
|
|
|
|
|
|
|
|
into a compartment or similarly enclosed, the minimum distances |
|
|
|
|
|
|
|
|
||
must be maintained. Do not cover the ventilation slot on the |
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|||
projector. Heat build-up can reduce the service life of your |
|
50cm |
|
50cm |
|
|
50cm |
|
||
|
|
|
|
|
||||||
projector, and can also be dangerous. |
|
|
|
|
|
|
|
|
●Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation holes.
●Remote Control Unit, supplied to this projector, emits the laser beam as the laser pointer function from Laser Light Window while pressing LASER button (for 1 minute / LASER POINTER INDICATOR lights red to indicate laser emission). Do not look into Laser Light Window or shine the laser beam on yourself or other people. Eye damage may result.
●If the projector is not to be used for an extended time, unplug the projector from the power outlet.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE OWNER'S MANUAL WITH THIS UNIT.
2
SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before the product is operated.
Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the manufacturer as they may cause hazards.
Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers.
An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.
The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.
This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided.
Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector.
This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.
Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by persons walking on it.
Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions:
a.When the power cord or plug is damaged or frayed.
b.If liquid has been spilled into the projector.
c.If the projector has been exposed to rain or water.
d.If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.
e.If the projector has been dropped or the cabinet has been damaged.
f.When the projector exhibits a distinct change in performance-this indicates a need for service.
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.
Voor de klanten in Nederland
Bij dit product zijn batterijen geleverd.
Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA.
3
COMPLIANCES
Federal Communication Commission Notice
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.
Model Numbers |
: PLC-SU32 |
Trade Name |
: Sanyo |
Responsible party |
: SANYO FISHER COMPANY |
Address |
: 21605 Plummer Street, Chatsworth, California 91311 |
Telephone No. |
: (818)998-7322 |
AC POWER CORD REQUIREMENT
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada :
AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be
unable to insert the plug into the outlet, contact your electrician. |
GROUND |
|
AC Power Cord for the United Kingdom :
This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus ASA . If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions.
If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed. The end of the flexible cord should be suitably prepared and the correct plug fitted. (See Over)
WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET OUTLET.
The Wires in this mains lead are coloured in accordance with the following code: Green-and-yellow ············ Earth
Blue ································· Neutral Brown ······························ Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
WARNING : THIS APPARATUS MUST BE EARTHED.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
4
TABLE OF CONTENTS
FEATURES AND DESIGN |
6 |
COMPUTER INPUT |
22 |
|
|
|
SELECTING INPUT SOURCE |
22 |
|
PREPARATION |
7 |
SELECTING COMPUTER SYSTEM |
22 |
|
COMPATIBLE COMPUTER SPECIFICATIONS |
23 |
|||
NAME OF EACH PART OF PROJECTOR |
7 |
PC ADJUSTMENT |
24 |
|
AUTO PC ADJUSTMENT |
24 |
|||
SETTING-UP PROJECTOR |
8 |
MANUAL PC ADJUSTMENT |
25 |
|
CONNECTING AC POWER CORD |
8 |
PICTURE IMAGE ADJUSTMENTS |
27 |
|
POSITIONING PROJECTOR |
9 |
IMAGE LEVEL SELECT |
27 |
|
ADJUSTABLE FEET |
9 |
IMAGE LEVEL ADJUSTMENT |
28 |
|
MOVING PROJECTOR |
10 |
PICTURE SCREEN ADJUSTMENT |
29 |
|
CONNECTING PROJECTOR |
11 |
VIDEO INPUT |
30 |
|
TERMINALS OF PROJECTOR |
11 |
SELECTING INPUT SOURCE |
30 |
|
CONNECTING TO COMPUTER |
12 |
SELECTING VIDEO SYSTEM |
31 |
|
CONNECTING TO VIDEO EQUIPMENT |
13 |
PICTURE IMAGE ADJUSTMENTS |
32 |
|
|
|
IMAGE LEVEL SELECT |
32 |
|
|
|
IMAGE LEVEL ADJUSTMENT |
33 |
|
BEFORE OPERATION |
14 |
PICTURE SCREEN ADJUSTMENT |
34 |
|
|
|
|||
OPERATION OF REMOTE CONTROL UNIT |
14 |
SETTING |
35 |
|
LASER POINTER FUNCTION |
14 |
|
|
|
REMOTE CONTROL BATTERIES INSTALLATION |
15 |
SETTING MENU |
35 |
|
TOP CONTROLS AND INDICATORS |
16 |
|||
|
|
|||
OPERATING ON-SCREEN MENU |
17 |
|
|
|
HOW TO OPERATE ON-SCREEN MENU |
17 |
APPENDIX |
37 |
|
FLOW OF ON-SCREEN MENU OPERATION |
17 |
|||
MENU BAR |
18 |
|
|
|
|
|
LAMP REPLACEMENT |
37 |
|
BASIC OPERATION |
19 |
|
|
|
TURNING ON / OFF PROJECTOR |
19 |
MAINTENANCE |
40 |
|
ADJUSTING SCREEN |
20 |
WARNING TEMP. INDICATOR |
40 |
|
ZOOM ADJUSTMENT |
20 |
AIR FILTER CARE AND CLEANING |
40 |
|
CLEANING PROJECTION LENS |
40 |
|||
FOCUS ADJUSTMENT |
20 |
|||
TROUBLESHOOTING |
41 |
|||
KEYSTONE ADJUSTMENT |
20 |
|||
PICTURE FREEZE FUNCTION |
20 |
TECHNICAL SPECIFICATIONS |
43 |
|
NO SHOW FUNCTION |
21 |
CONFIGURATIONS OF TERMINALS |
44 |
|
P-TIMER FUNCTION |
21 |
OPTIONAL PARTS |
45 |
|
SOUND ADJUSTMENT |
21 |
|
|
TRADEMARKS
●Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
●IBM, VGA, XGA, and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
●Windows and PowerPoint are registered trademarks of Microsoft Corporation.
●Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its respective corporation.
5
FEATURES AND DESIGN
This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology.
Compact Design |
|
Keystone Correction |
|
|
|
This projector is extremely compact in size and weight. It is designed to carry and work anywhere you wish to use.
Compatibility
This projector widely accepts various video and computer input signals including;
●Computers
IBM-compatible or Macintosh computer up to 1280 x 1024 resolution.
●6 Color Systems
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL- N color system can be connected.
●Component Video
Component video signal, such as a DVD player output high definition TV signals including 480i, 480p, 575i, 575p, 720p, 1035i or 1080i, can be connected.
●S-Video
S-Video signal, such as a S-VHS VCR output signal, can be connected.
High Resolution Image
This projector provides 800 x 600 dots resolution for computer input and 750 horizontal TV lines. Resolution from a computer between SVGA (800 x 600) and SXGA (1280 x 1024) is compressed into 800 x 600 dots. This projector cannot display image of over 1280 x 1024 dots. When resolution of your computer is over than 1280 x 1024, reset a computer output for lower resolution.
Multi-Scan System
This projector has Multi-Scan System to conform to almost all computer output signals quickly. There is no need for troublesome manual adjustment of frequency and other settings.
Positioning height of a projector may result in distorted image being displayed in a trapezoid shape. Keystone Correction solves this problem by digitally altering projection to produce undistorted images.
Power Management
Power Management function is provided to reduce power consumption while a projector is not in use.
This Power Management function operates to turn Projection Lamp off when a projector detects signal interruption and any button is not pressed over 5 minutes. Projection Lamp is automatically turned on again when a projector detects signal or any operation button is pressed.
This projector is shipped with this function ON.
Digital Visual Interface
This projector is equipped with DVI 29-pin terminal for connecting DVI output from a computer.
Laser Pointer Function
Remote Control Unit supplied with this projector includes Laser Pointer function. This function helps you to make a smart presentation on a projected screen.
Wireless Mouse
Remote Control Unit supplied with this projector has Wireless Mouse function for a connected computer. This function enables you to operate both projector and computer with Remote Control Unit only.
Multilanguage Menu Display
Operation menu is displayed in; English, German, French, Italian, Spanish, Portuguese, Dutch, Swedish, Chinese, Korean or Japanese.
One-Touch Auto PC Adjustment
Incoming computer video signals are recognized and the best adjustment is automatically set by Auto PC Adjustment. No complicated setup is necessary and projection is always precise.
Media Card Imager (Optional)
Optional Media Card Imager is available for this projector. For the Media Card Imager, contact the dealer where you purchased this projector.
Digital Zoom (for Computer)
Digital Zoom function adjusts the image size to approx. 1/4 ~ 49 times of original image size, allowing you to focus on crucial information at a presentation.
Wireless Imager (Optional)
This projector can be operated through Wireless LAN by attaching Wireless imager that is optionally supplied. For the Wireless Imager, contact the dealer where you purchased the projector.
6
PREPARATION
NAME OF EACH PART OF PROJECTOR
FRONT
CARRY HANDLE
INFRARED
REMOTE RECEIVER
PROJECTION LENS
BACK
TOP CONTROLS
AND INDICATORS
POWER CORD CONNECTOR
BOTTOM
LAMP COVER
ADJUSTABLE FEET
AND
FEET LOCK LATCHES
EXHAUST VENTS
HOT AIR EXHAUSTED !
Air blown from Exhaust Vents is hot. When using or installing projector, following precautions should be taken.
● Do not put any flammable object near these vents.
● Keep front grills at least 3’(1m) away from any object, especially heatsensitive object.
● Do not touch this area, especially screw and metallic part. This area will become hot while a projector is used.
This projector detects internal temperature and automatically controls operating power of Cooling Fans.
LENS COVER
INFRARED
REMOTE RECEIVER
SPEAKER
TERMINALS
AND CONNECTORS
AIR FILTER
AIR INTAKE VENTS
(Back and Bottom)
This projector is equipped with Cooling Fans for protection from overheating. Pay attention to the following to ensure proper ventilation and avoid a possible risk of fire and malfunction.
● Do not cover vent slots.
●Keep back and bottom clear of any object. Obstructions may block cooling air.
7
PREPARATION
SETTING-UP PROJECTOR
CONNECTING AC POWER CORD
This projector uses nominal input voltages of 100-120 V or 200-240 V AC. This projector automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure of the type of power supply being in use.
Connect a projector with a peripheral equipment before turning a projector on. (Refer to pages 11 ~ 13 for connection.)
CAUTION
For safety, unplug AC Power Cord when an appliance is not used.
When this projector is connected to the outlet with AC Power Cord, an appliance is in Stand-by Mode and consumes a little electric power.
Connect AC Power Cord (supplied) to a projector. The AC outlet must be near this equipment and must be easily accessible.
NOTE ON THE POWER CORD
AC Power Cord must meet requirement of the country where you use a projector.
Confirm an AC plug type with the chart below and proper AC Power Cord must be used.
If supplied AC Power Cord does not match your AC outlet, contact your sales dealer.
Projector side |
|
|
|
|
|
AC Outlet side |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
For the U.S.A. and Canada |
For Continental Europe |
For the U.K. |
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ground |
|
|
|
|
To POWER CORD |
|
|
|
|
|
To the AC Outlet. |
|
To the AC Outlet. |
|
|
|||
CONNECTOR on your |
|
|
To the AC Outlet. |
|
(200 - 240 V AC) |
|
|
(120 V AC) |
|
|
|||
projector. |
|
|
(200 - 240 V AC) |
|
|
|
|
|
|
|
|
||
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
8
PREPARATION
POSITIONING PROJECTOR
●This projector is designed to
●The projector can be focused
●Refer to the figure below to
H1 : H2 = 9 : 1
ROOM LIGHT
The brightness in a room has a great influence on picture quality. It is recommended to limit ambient lighting in order to provide the best image.
26.
|
|
|
21.3’ (6.5m) |
|
Max. Zoom |
|
|
|
13.1’ (4.0m) |
|
|
Min. Zoom |
|
|
5.3’ (1.6m) |
|
160” |
|
||
|
|
|
153” |
|
|
|
|
|
100” |
|
|
|
|
|
|
115” |
|
|
|
|
|
|
|
|
|
|
|
|
40” |
77” |
|
|
|
|
|
31” |
|
|
|
|
H2 |
|
|
|
|
|
|
|
Screen Size |
31" |
40” |
100” |
160” |
200” |
300” |
|
|
|
|
|
|
|
(W x H) mm |
630 x 472 |
813 x 610 |
2032 x 1524 |
3251 x 2438 |
4064 x 3048 |
6096 x 4572 |
|
||||||
Zoom (min) |
5.3' (1.6m) |
6.9' (2.1m) |
17.4' (5.3m) |
27.9' (8.5m) |
34.8' (10.6m) |
––––– |
Zoom (max) |
––––– |
5.2' (1.6m) |
13.1' (4.0m) |
21.3' (6.5m) |
26.6' (8.1m) |
40.0' (12.2m) |
ADJUSTABLE FEET
Picture tilt and projection angle can be adjusted by rotating ADJUSTABLE FEET. Projection angle can be adjusted to 15.6 degrees.
1 |
Lift the front of a projector and pull FEET LOCK LATCHES |
|
on the both sides of a projector. |
2 |
Release FEET LOCK LATCHES to lock ADJUSTABLE FEET |
|
and rotate ADJUSTABLE FEET to fine tune position and tilt. |
3 |
To retract ADJUSTABLE FEET, lift the front of a projector |
|
and pull and undo FEET LOCK LATCHES. |
|
Keystone distortion of a projected image can be adjusted by |
|
Menu Operation. (Refer to P20 and 35.) |
CAUTION
|
|
FEET LOCK |
Avoid positioning a projector with the angle of more than 20 |
ADJUSTABLE FEET |
LATCHES |
|
||
degrees. Projection Lamp may malfunction. |
|
|
9
PREPARATION
MOVING PROJECTOR
Use Carry Handle when moving a projector.
When moving a projector, replace Lens Cover and retract Adjustable Feet to prevent damage to the lens and cabinet.
When a projector is not in use for an extended period, put it into the case (carrying bag) supplied with a projector.
CAUTION
Carrying Bag (supplied) is intended for protection from dust and scratches on the surface of a cabinet, and it is not designed to protect an appliance from external forces. Do not transport a projector through a courier or transport services with this bag. The projector can be damaged. When handling a projector, do not drop, bump, subject it to strong forces or put other things on the cabinet.
CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR
●Do not drop or bump a projector, otherwise damages or malfunctions may result.
●When carrying a projector, use a suitable carrying case.
●Do not transport a projector by using a courier or transport service in an unsuitable transport case. This may cause damage to a projector. To transport a projector through a courier or transport service, consult your dealer for best way.
10
CONNECTING PROJECTOR
TERMINALS OF PROJECTOR
This projector has input and output terminals on its back for connecting computers and video equipment. Refer to figures on pages 11 to 13 and connect properly.
S-VIDEO INPUT JACK |
|
AUDIO INPUT JACKS |
VIDEO INPUT JACKS |
||
Connect the S-VIDEO |
Connect the audio output |
Connect the composite video |
|||
output from video |
from video equipment to |
output from video equipment |
|||
equipment to |
this |
these jacks. |
|
to VIDEO/Y jack or connect |
|
jack. (Refer to P13.) |
(Refer to P13.) |
|
the component video outputs |
||
|
|
When the audio output |
to VIDEO/Y, Pb/Cb and |
||
|
|
is monaural, connect it |
Pr/Cr jacks. (Refer to P13.) |
||
|
|
to L (MONO) jack. |
|
||
COMPUTER IN |
|
VIDEO |
Pb / Cb – Pr / Cr |
|
|
DVI - I |
R – AUDIO IN – L (MONO) Y – |
|
|||
|
S – VIDEO |
AUDIO IN |
R – AUDIO OUT – L |
||
|
|
|
COMPUTER |
|
RESET |
MCI / WI |
|
|
|
|
|
|
|
MONITOR OUT |
USB |
CONTROL PORT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MONITOR OUTPUT |
|
|
|
COMPUTER AUDIO |
||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TERMINAL |
|
|
|
|
|
|
INPUT JACK |
|||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
Connect a monitor to |
Connect the audio output |
||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
this terminal. This |
(stereo) from computer to |
||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
terminal outputs a |
this jack. (Refer to P12.) |
||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
computer input signal. |
|
|
|
|
|
|
|
|
|||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
(Refer to P12.) |
|
|
|
|
|
|
|
|
COMPUTER INPUT (DIGITAL/ANALOG)
Media Card Imager / Wireless Imager
TERMINAL
Connect computer output (Digital / Analog DVI-I type), Media Card Imager*, or Wireless Imager* to this terminal.
*optional accessories
AUDIO OUTPUT JACKS
Connect an external audio amplifier to these jacks.
(Refer to P12, 13.)
RESET BUTTON
This projector uses a micro processor to control this unit, and occasionally, this micro processor may malfunction and need to be reset. This can be done by pressing RESET button with a pen, which will shut down and restart the unit. Do not use RESET function excessively.
CONTROL PORT CONNECTOR
When controlling the computer with Remote Control Unit of this projector, connect the mouse port of your personal computer to this connector. (Refer to P12.)
USB CONNECTOR (Series B)
When controlling the computer with Remote Control Unit of this projector, connect USB port of your personal computer to this connector. (Refer to P12.)
Do not press this button. This button is used for our optional accessories.
11
CONNECTING PROJECTOR
CONNECTING TO COMPUTER
Cables used for connection ( = Cable or adapter is not supplied with this projector.)
• VGA Cable (HDB 15 pin) |
• USB Cable |
• Control Cable for PS/2 Port |
• MAC Adapter (When connecting to Macintosh computer) |
• DVI-Digital Cable (for Single Link T.M.D.S.) |
• DVI/VGA Adapter |
• Control Cable for Serial Port , or ADB Port |
• Audio Cables (RCA x 2 and Mini Plug (stereo) x 1) |
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)
|
Desktop type |
Laptop type |
Monitor Output |
Monitor Input Audio Output |
USB port Serial port PS/2 port ADB port |
MAC Adapter
Set slide switches according to the chart below.
|
VGA |
Audio |
DVI Cable |
Cable |
Cable |
|
(stereo) |
|
|
|
VGA Cable
USB |
Cable |
Control Cable for Serial Port
Terminal |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Control Cable |
Control Cable |
|||
for PS/2 Port |
for ADB Port |
Terminal |
Terminal |
|
COMPUTER IN DVI-I |
MONITOR OUT |
AUDIO IN COMPUTER |
USB |
Use one of these Control |
|||
|
|
|
|
|
|
|
Cables corresponding with |
|
DVI/VGA |
|
|
|
|
|
|
the terminal |
of your |
|
|
|
|
|
|
computer. |
|
|
Adapter |
COMPUTER IN |
|
|
VIDEO |
|
|
|
|
R – AUDIO IN – L (MONO) |
Pb / Cb – Pr / Cr |
|
CONTROL PORT |
|
||||
|
DVI - I |
Y – |
|
|
||||
COMPUTER IN DVI-I |
|
|
|
|
|
|
|
|
|
|
S – VIDEO |
AUDIO IN |
R – AUDIO OUT – L |
|
|
||
|
|
|
COMPUTER |
|
RESET |
|
|
|
|
|
|
|
|
|
|
|
|
|
MCI / WI |
|
|
|
|
|
|
|
|
|
MONITOR OUT |
USB |
CONTROL PORT |
|
|
||
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
Terminals |
|
|
|
|
|
|
|
|
of the Projector |
|
|
|
|
|
|
|
AUDIO OUT |
|
|
NOTE : |
|
|
|
|
|
|
|
|
|
|
|
|
When connecting the cable, the power |
|
|
||||||||||
cords of both the projector and the external |
|
|
||||||||||
equipment should be disconnected from |
|
|
||||||||||
AC outlet. Turn the projector and |
Audio Cable |
|
||||||||||
peripheral equipment on before the |
|
|||||||||||
computer is switched on. |
|
|
|
|
|
|
|
(stereo) |
|
|||
MAC ADAPTER (Not supplied) |
|
|
|
|
|
|
|
|
|
|||
Set switches as shown in the table ON |
|
|
|
|
|
|
|
Audio Input |
|
|||
below depending on RESOLU- |
|
|
|
ON |
|
|
DIP |
|
||||
TION MODE that you want to use |
|
|
1 |
2 |
3 |
4 |
5 |
6 |
|
|
||
before you turn on projector and |
OFF |
|
|
|
|
|
|
|
External Audio Equipment |
|||
computer. |
|
|
|
|
|
|
|
|
|
|
|
Audio Speaker |
|
1 |
2 |
3 |
4 |
|
|
5 |
|
|
6 |
Audio Amplifier |
|
13" MODE (640 x 480) |
ON |
ON |
OFF |
OFF |
OFF |
|
OFF |
(stereo) |
||||
16" MODE (832 x 624) |
OFF |
ON |
OFF |
ON |
OFF |
|
OFF |
|
|
|||
19" MODE (1024 x 768) |
OFF |
ON |
ON |
OFF |
OFF |
|
OFF |
|
|
|||
21" MODE (1152 x 870) |
ON |
ON |
ON |
ON |
OFF |
|
OFF |
|
|
12
CONNECTING PROJECTOR
CONNECTING TO VIDEO EQUIPMENT
Cables used for connection ( = Cable is not supplied with this projector.)
•Video Cable (RCA x 1 or RCA x 3)
•S-VIDEO Cable
•Audio Cable (RCA x 2)
Video Source (example) |
|
|
Component video output equipment. |
|
|
|
|
Video Cassette Recorder |
Video Disc Player |
(such as DVD player or high-definition TV source.) |
S-VIDEO Output |
Composite |
Component Video Output |
Audio Output |
||||||||||||||||||||||
Video Output |
(Y, Pb/Cb, Pr/Cr) |
(R, L) |
|||||||||||||||||||||||
|
|
|
|||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
S-VIDEO |
Video Cable |
Video Cable |
Audio Cable |
Cable |
(RCA x 1) |
(RCA x 3) |
(RCA x 2) |
S-VIDEO |
VIDEO |
Y - Pb/Cb - Pr/Cr |
AUDIO IN |
|
|
COMPUTER IN |
|
VIDEO |
Pb / Cb – Pr / Cr |
|
|
DVI - I |
R – AUDIO IN – L (MONO) Y – |
|
||
|
|
S – VIDEO |
AUDIO IN |
R – AUDIO OUT – L |
|
|
|
|
COMPUTER |
|
RESET |
|
|
|
|
|
|
Use any of VIDEO jack, S-VIDEO |
|
|
|
|
|
jack, or Y-Pb/Cb-Pr/Cr jacks. |
MCI / WI |
|
|
|
|
• When both VIDEO jack and S- |
|
MONITOR OUT |
|
|
|
VIDEO jack are connected, S- |
|
USB |
CONTROL PORT |
||
|
|
|
|||
VIDEO jack has priority over |
|
|
|
|
|
VIDEO jack. |
|
|
|
|
Terminals |
• When both Y-Pb/Cb-Pr/Cr jacks |
|
|
|
|
|
and S-VIDEO jack are connected, |
|
|
|
|
of the Projector |
Y-Pb/Cb-Pr/Cr jacks has priority |
|
|
AUDIO OUT |
||
over S-VIDEO jack. |
|
|
Audio Cable (Stereo)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Audio Input |
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
NOTE : |
|
|
|
External Audio Equipment |
|
|
||||||||||||
|
|
|
|
When connecting the cable, the power |
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Audio Speaker |
|
|||
|
|
|
|
cords of both the projector and the external |
|
|
|
Audio Amplifier |
|
|
|
|||||||||||
|
|
|
|
equipment should be disconnected from |
|
|
|
|
|
|
(stereo) |
|
||||||||||
|
|
|
|
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
AC outlet. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
13
BEFORE OPERATION
OPERATION OF REMOTE CONTROL UNIT
Left Side
ON
ALL
OFF
ALL-OFF SWITCH
When using Remote Control Unit, turn this switch to “ON.” And turn it to “ALL OFF” when it is not used.
LASER POINTER INDICATOR
Lights red while laser beam is emitted from Laser Light Window.
MENU BUTTON
Used to select MENU operation. (P17, 18)
SELECT BUTTON
Used to execute the item selected, or to expand or compress the image in DIGITAL ZOOM +/– mode. (P29)
It is also used as a PC mouse in Wireless Mouse Operation. (P39)
LASER BUTTON
Used to operate Laser Pointer Function. Laser beam is emitted while pressing this button within 1 minute.
When using this Laser Pointer for more than 1 minute, release LASER button and press it again.
ON-OFF
ZOOM FOCUS VOLUME
LOCK
MUTE D.ZOOM INPUT
MENU
LASER
KEYSTONE |
|
NO SHOW |
FREEZE |
AUTO PC ADJ. |
IMAGE |
P-TIMER |
|
POWER ON-OFF BUTTON
Used to turn projector on or off. (P19)
INPUT BUTTON
Used to select input source. (P22, 30)
POINT BUTTON
Used to move a pointer on ON-SCREEN MENU, adjust each item, or pan image in DIGITAL ZOOM +/– mode. (P29)
It is also used as a PC mouse in Wireless Mouse Operation. (P39)
When pressing the center of this button, it works as SELECT button.
RIGHT CLICK BUTTON
Used as a PC mouse in Wireless Mouse Operation. (P39)
P-TIMER BUTTON
Used to operate P-TIMER function. (P21)
LASER POINTER FUNCTION
This Remote Control Unit emits a laser beam as the laser pointer function from Laser Light Window. When LASER button is pressed, the laser light goes on. And when LASER button is being pressed for more than 1 minute or LASER button is released, light goes off. LASER POINTER INDICATOR lights RED and Laser is emitted with RED light to indicate laser beam is being emitted.
The laser emitted is a class II laser; therefore, do not look into Laser Light Window or shine the laser beam on yourself or other people. The three marks bellow are the caution labels for the laser beam.
CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result hazardous radiation exposure.
These caution labels are put on the Remote Control Unit.
LASER POINTER INDICATOR
Laser Light Window
14
BEFORE OPERATION
ZOOM BUTTON |
|
ON-OFF |
Used to adjust zoom. |
|
|
(P20) |
ZOOM |
FOCUS VOLUME |
|
||
|
LOCK |
|
FOCUS BUTTON |
MUTE |
D.ZOOM INPUT |
Used to adjust focus. |
|
|
(P20) |
|
|
|
MENU |
|
MUTE BUTTON |
|
|
Used to mute sound.(P21) |
|
|
KEYSTONE BUTTON
Used to correct keystone distortion. (P20, 35)
NO SHOW BUTTON
Used to turn the picture into black image. (P21)
AUTO PC ADJ. BUTTON
Used to operate AUTO PC Adjustment function. (P24)
LASER
KEYSTONE |
|
NO SHOW |
FREEZE |
AUTO PC ADJ. |
IMAGE |
P-TIMER |
|
VOLUME BUTTON
Used to adjust volume. (P21)
D.ZOOM BUTTON
Used to select DIGITAL ZOOM +/– mode and resize image. (P29)
Operating Range
Point Remote Control Unit toward projector (Receiver Window) whenever pressing any button. Maximum operating range for Remote Control Unit is about 16.4’ (5m) and 60° in front and rear of the projector.
16.4’
(5 m) 60°
FREEZE BUTTON
Used to freeze the picture. (P20)
IMAGE BUTTON
Used to select image level. (P27, 32)
60°
16.4’ (5 m)
|
REMOTE CONTROL BATTERIES |
1 |
2 |
Press the lid downward and slide it.
Two AA size batteries
For correct polarity (+ and –), be sure the battery terminals are in contact with the pins in the compartment.
To insure safe operation, please observe the following precautions :
●Use (2) AA, UM3 or R06 type alkaline batteries.
●Replace two batteries at the same time.
●Do not use a new battery with an used battery.
●Avoid contact with water or liquid.
●Do not expose Remote Control Unit to moisture, or heat.
●Do not drop Remote Control Unit.
●If a battery has leaked on Remote Control Unit, carefully wipe the case clean and load new batteries.
●Danger of explosion if battery is incorrectly replaced.
●Dispose of used batteries according to battery manufacturer's instructions and local rules.
15