Sanyo PLC-HP7000L Quick Reference Guide
Use this book as a reference guide when setting up the projector. For
detailed information about installation, setup, and operation of the
projector, refer to the owner’s manual on the CD-ROM.
READ THE SAFETY INSTRUCTIONS IN THE OWNER’S MANUAL
(CD-ROM) BEFORE USING THE PROJECTOR.
Quick Reference Guide
Multimedia Projector
MODEL
PLC-HP7000L
Projection lens is optional.
2
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE EXCEPT LAMP REPLACEMENT.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES
THAT DANGEROUS VOLTAGE
CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS
UNIT.
THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE
OWNER'S MANUAL WITH THIS UNIT.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SAFETY PRECAUTIONS
– Do not cover the ventilation slot on the
projector. Heat build-up can shorten the
service life of your projector, and can also be
dangerous.
– If the projector is unused for an extended
time, unplug the projector from the power
outlet.
– Do not project the same image for a long
time. The afterimage may remain on the
LCD panels by the characteristic of panel.
– Do not set the projector in greasy, wet,
or smoky conditions such as in a kitchen
to prevent a breakdown or a disaster. If
the projector comes in contact with oil or
chemicals, it may become deteriorated.
Hot air is exhausted from the exhaust vent.
When using or installing the projector, the
following precautions should be taken.
– Do not put any flammable object or spray can
near the projector, hot air is exhausted from
the air vents.
– Keep the exhaust vent at least 1 m away from
any objects.
– Do not touch peripheral parts of the
exhaust vent, especially screws and
metallic parts. These areas will become
hot while the projector is being used.
– Do not put anything on the cabinet.
Objects put on the cabinet will not only get
damaged but also may cause fire hazard
by heat.
WARNING:
● THIS APPARATUS MUST BE EARTHED.
● TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
– This projector produces intense light from the
projection lens. Do not stare directly into the
lens, otherwise eye damage could result. Be
especially careful that children do not stare
directly into the beam.
– Install the projector in a proper position.
Improper positioning may reduce the lamp life
and result in severe accident or fire hazard.
– Allowing the proper amount of space on the
top, sides, and rear of the projector cabinet is
critical for proper air circulation and cooling of
the unit.
Exhaust Vent
(Hot air exhaust)
Air Intake Vent
Authorized Representative and Address:
SANYO Sales & Marketing Europe GmbH
Stahlgruberring 4, D-81829 Munich, Germany
Manufacturer and Address:
SANYO Electric Co., Ltd.
1-1, Sanyo-cho, Daito City, Osaka 574-8534,
Japan
Air flow
CAUTION
Not for use in a computer room as defined in the
Standard for the Protection of Electronic Computer/
Data Processing Equipment, ANSI/NFPA 75.
1.5' (50 cm)
1.5' (50 cm) 1.5' (50 cm)
3' (1 m)
SIDE and TOP
REAR
3
All the safety and operating instructions should
be read before the product is operated.
Read all of the instructions mentioned here and
retain them for later use. Unplug this projector
from AC power supply before cleaning. Do not
use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
Follow all warnings and instructions marked on
the projector.
For added protection to the projector during a
lightning storm, or when it is left unattended
and unused for long periods of time, unplug it
from the wall outlet. This will prevent damage
due to lightning and power line surges.
Do not expose this unit to rain or use near
water... for example, in a wet basement, near a
swimming pool, etc...
Do not use attachments not recommended by
the manufacturer as they may cause hazards.
Do not place this projector on an unstable cart,
stand, or table. The projector may fall, causing
serious injury to a child or adult, and serious
damage to the projector. Use only with a cart
or stand recommended by the manufacturer, or
sold with the projector. Wall or shelf mounting
should follow the manufacturer’s instructions,
and should use a mounting kit approved by the
manufacturers.
An appliance and cart
combination should be
moved with care. Quick
stops, excessive force, and
uneven surfaces may cause
the appliance and cart
combination to overturn.
Slots and openings in the
back and bottom of the cabinet are provided for
ventilation, to ensure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with
cloth or other materials, and the bottom
opening should not be blocked by placing the
projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed
near or over a radiator or heat register.
This projector should not be placed in a built-in
installation such as a book case unless proper
ventilation is provided.
Never push objects of any kind into this
projector through cabinet slots as they may
touch dangerous voltage points or short out
parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
Do not install the projector near the ventilation
duct of air-conditioning equipment.
This projector should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supplied, consult your authorized dealer or
local power company.
Do not overload wall outlets and extension
cords as this can result in fire or electric shock.
Do not allow anything to rest on the power
cord. Do not locate this projector where the
cord may be damaged by persons walking on
it.
Do not attempt to service this projector
yourself as opening or removing covers may
expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer
servicing to qualified service personnel under
the following conditions:
a. When the power cord or plug is damaged or
frayed.
b. If liquid has been spilled into the
projector.
c. If the projector has been exposed to rain
or water.
d. If the projector does not operate normally
by following the operating instructions.
Adjust only those controls that are covered
by the operating instructions as improper
adjustment of other controls may result in
damage and will often require extensive
work by a qualified technician to restore the
projector to normal operation.
e. If the projector has been dropped or the
cabinet has been damaged.
f. When the projector exhibits a distinct
change in performance- this indicates a
need for service.
When replacement parts are required, be sure
the service technician has used replacement
parts specified by the manufacturer that have
the same characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to
this projector, ask the service technician to
perform routine safety checks to determine that
the projector is in safe operating condition.
English
4
FOR EU USERS
The symbol mark and recycling systems described below apply to EU countries and do not apply
to countries in other areas of the world.
Your product is designed and manufactured with high quality materials and components which
can be recycled and/or reused.
The symbol mark means that electrical and electronic equipment, batteries and accumulators, at
their end-of-life, should be disposed of separately from your household waste.
Note:
If a chemical symbol is printed beneath the symbol mark, this chemical symbol means that the
battery or accumulator contains a heavy metal at a certain concentration.
This will be indicated as follows: Hg: mercury, Cd: cadmium, Pb: lead
In the European Union there are separate collection systems for used electrical and electronic
equipment, batteries and accumulators.
Please, dispose of them correctly at your local community waste collection/
recycling centre.
Please, help us to conserve the environment we live in!
Compliances
NOTE FOR CUSTOMERS IN THE US
Hg LAMP(S) INSIDE THIS PRODUCT
CONTAIN MERCURY AND MUST BE
RECYCLED OR DISPOSED OF ACCORDING
TO LOCAL, STATE OR FEDERAL LAWS.
TÜRK KULLANICILAR İÇİN
Bu ürün, EEE yönetmeliğine uygundur.
(ELEKTRİKLİ VE ELEKTRONİK
EŞYALARDA BAZI ZARARLI MADDELERİN
KULLANIMININ SINIRLANDIRILMASINA
DAİR YÖNETMELİK)
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Do not make any changes or modifications to the equipment unless otherwise specified in the
instructions. If such changes or modifications should be made, you could be required to stop operation
of the equipment.
Canadian Radio Interference Regulations
This Class A digital apparatus meets all requirements of the Canadian ICES-003.
WARNING
This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
5
AC Power Cord for the United Kingdom:
This cord is already fitted with a moulded plug incorporating a fuse, the value of which is
indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA
approved BS 1362 fuse must be used of the same rating, marked thus
A S A
. If the fuse cover
is detachable, never use the plug with the cover omitted. If a replacement fuse cover is
required, ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or
orange). Fuse covers are available from the Parts Department indicated in your User
Instructions. If the plug supplied is not suitable for your socket outlet, it should be cut off and
destroyed. The end of the flexible cord should be suitably prepared and the correct plug
fitted.
WARNING: A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A
LIVE SOCKET OUTLET.
The Wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow ············ Earth
Blue ·······························Neutral
Brown ·····························Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the
coloured markings identifying the terminals in your plug proceed as follows: The wire which
is coloured green-and-yellow must be connected to the terminal in the plug which is marked
by the letter E or by the safety earth symbol
or coloured green or green-and-yellow. The
wire which is coloured blue must be connected to the terminal which is marked with the letter
N or coloured black. The wire which is coloured brown must be connected to the terminal
which is marked with the letter L or coloured red.
WARNING: THIS APPARATUS MUST BE EARTHED.
The AC Power Cord supplied with this projector meets the requirement for use in the country you
purchased it.
AC Power Cord for the United States and Canada:
AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to
be sure that the plug will fit into the power outlet. Do not try to defeat this safety
feature. Should you be unable to insert the plug into the outlet, contact your
electrician.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY
ACCESSIBLE.
AC Power Cord Requirement
Unplug the power cords of both the projector and external equipment from the AC outlet
before connecting cables.
English
6
Moving the Projector
Use the handle grip when moving the projector.
Retract the adjustable feet to prevent damage to the
lens and cabinet when carrying.
When this projector is not in use for an extended period,
put it into a suitable case to protect the projector.
Handle grip
Use the projector properly in specified positions. Improper positioning may shorten the lamp life and
result in severe accident or fire hazard.
This projector can project the picture in upward, downward, or inclined position in perpendicular
direction to the horizontal plane. When installing the projector in downwardly inclined position, install
the projector bottom side up.
Avoid positioning the projector as described below when installing.
Positioning Precautions
Do not tilt the projector
more than 10 degrees from
side to side.
Do not put the projector
on either side to project an
image.
10˚
10˚
10° 10°
10°
10°
In upward projection, do not tilt
the projector over 10 degrees
right and left.
In downward projection, do not
tilt the projector over 10 degrees
right and left.
Installing the Projector in Proper Directions
– Do not drop or bump the projector, otherwise
damages or malfunctions may result.
– When carrying the projector, use a suitable
carrying case.
– Do not transport the projector by courier or
any other transport service in an unsuitable
transport case. This may cause damage
to the projector. For information about
transporting the projector by courier or any
other transport service, consult your dealer.
– Do not put the projector in a case before it is
cooled enough.
CAUTION IN CARRYING OR
TRANSPORTING THE PROJECTOR
7
This projector uses nominal input voltages of 100–240 V AC and it automatically selects the correct
input voltage.
Connecting the AC Power Cord
Note:
Unplug the AC power cord when the projector
is not in use. When this projector is connected
to an outlet with
the AC power cord, it is in
Stand-by mode and consumes a little electric
power.
CAUTION
The AC outlet must be near this equipment
and must be easily accessible.
To the AC outlet.
(200 - 240 V AC)
NOTE ON THE POWER CORD
AC power cord must meet requirement of the country where you use the projector.
Confirm the AC plug type with the chart below and proper AC power cord must be used.
If supplied AC power cord does not match your AC outlet, contact your sales dealer.
To power cord
connector on your
projector.
Projector side
AC outlet side
Ground
To the AC outlet.
(120 V AC)
For the U.S.A. and Canada
To the AC outlet.
(200 - 240 V AC)
For the U.K.
For Continental Europe
CAUTION
Projection lens is a motorized lens. Please note the followings when using the projector.
● Do not touch the lens while it is moving as this could cause injury to the fingers.
● Never allow children to touch the lens.
Cautions in Handling the Projector
Do not hold the lens or the top cover when lifting or moving the projector. Doing so may cause
damage to the lens and the projector.
Care must be taken when handling the projector; do not drop, bump, subject it to strong forces, or
put other things on the cabinet.
Ground
Connect the AC power cord
(supplied) to the projector.
English
Loading...