Sanyo PDP32H1W User Manual
Owner's Manual
PDP-32H1W
Multimedia Plasma Monitor
MODEL
2
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE
OWNER'S MANUAL WITH THIS UNIT.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Before operating this Plasma Monitor, read this manual thoroughly and operate the Plasma Monitor properly.
This Plasma Monitor provides many convenient features and functions. Operating the Plasma Monitor properly
enables you to manage those features and maintains it in better condition for a considerable time.
Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other
accidents.
If your Plasma Monitor seems to operate improperly, read this manual again, check operations and cable connections
and try the solutions in the “Trouble-shooting” section of the end of this booklet. If the problem still persists, contact
the sales dealer where you purchased the Plasma Monitor or the service center.
TO THE OWNER
SAFETY PRECAUTIONS
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
● This Plasma Monitor should be set in the way indicated. If not, it may result in a fire hazard.
● Take appropriate space on the top, sides and rear of the Plasma Monitor cabinet for allowing air circulation and
cooling the Plasma Monitor. Minimum distance should be taken. If the Plasma Monitor is to be built into a
compartment or similarly enclosed, the minimum distances must
be maintained. Do not cover the ventilation slot on the Plasma
Monitor. Heat build-up can reduce the life of your Plasma
Monitor, and can also be dangerous.
● If the Plasma Monitor is not to be used for an extended time,
unplug the Plasma Monitor from the power outlet.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.
SIDE and TOP
REAR
CAUTION IN INSTALLING
●
Handle the
Plasma
Monitor carefully when installing it and do not drop.
●
Locate set away from heat, excessive dust, and direct sunlight.
●
For correct installation and mounting it is strongly recommended to use a trained, authorized dealer. Failure to
follow correct mounting procedures could result in damage to the equipment or injury to the installer.
10 cm
10 cm
10 cm
6 cm
NOTE :
When Plasma Monitor is not used for a long period of time, unlighting dots may be observed. This is caused by
characteristic of the Plasma Monitor. If this occurs, turn the Plasma Monitor on and leave it on about 1 hour. These
dots will gradually disappear.
3
SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before
the product is operated.
Read all of the instructions given here and retain them for later
use. Unplug this
Plasma Monitor
from AC power supply
before cleaning. Do not use liquid or aerosol cleaners. Clean
only with dry cloth.
Follow all warnings and instructions marked on the
Plasma
Monitor
.
For added protection to the
Plasma Monitor
during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet. This will
prevent damage due to lightning and power line surges.
Do not expose this Plasma Monitor to rain or use near water...
for example, in a wet basement, near a swimming pool, etc...
The Plasma Monitor shall not be exposed to dripping or
splashing. No objects filled with liquids, such as vases, shall
be placed on the Plasma Monitor.
Only use attachments/accessories specified by the
manufacturer.
Do not place this
Plasma Monitor
on an unstable cart, stand,
or table. The
Plasma Monitor
may fall, causing serious injury
to a child or adult, and serious damage to the
Plasma
Monitor
. Use only with a cart or stand recommended by the
manufacturer, or sold with the
Plasma Monitor
.
CAUTION:
This
Plasma Monitor
for use only with following Stand and
Mount Unit
. Use with other stands or mount units is capable of
resulting in instability causing possible injury.
SANYO Floor stand KA-TD-H10W
SANYO Tilt mount unit KA-TI-H10
SANYO Wall mount unit KA-WA-H10WV
SANYO Ceiling mount unit KA-CH-H10
An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
Slots and openings in the back and top of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
Do not block any ventilation openings. Install in accordance
with the manufacturer's instructions. Do not install near any
heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
This
Plasma Monitor
should not be placed in a built-in
installation such as a book case unless proper ventilation is
provided.
Never push objects of any kind into this
Plasma Monitor
through cabinet slots as they may touch dangerous voltage
points or short out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the
Plasma Monitor
.
This
Plasma Monitor
should be operated only from the type
of power source indicated on the marking label. If you are not
sure of the type of power supplied, consult your authorized
dealer or local power company.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Protect the power cord from being walked on
or pinched particularly at plugs. convenience receptacles, and
the point where they exit from the apparatus.
Do not attempt to service this
Plasma Monitor
yourself as
opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified
service personnel.
Unplug this
Plasma Monitor
from wall outlet and refer
servicing to qualified service personnel under the following
conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the
Plasma Monitor
.
c. If the
Plasma Monitor
has been exposed to rain or water.
d. If the
Plasma Monitor
does not operate normally by
following the operating instructions. Adjust only those
controls that are covered by the operating instructions as
improper adjustment of other controls may result in damage
and will often require extensive work by a qualified
technician to restore the
Plasma Monitor
to normal
operation.
e. If the
Plasma Monitor
has been dropped or the cabinet
has been damaged.
f. When the
Plasma Monitor
exhibits a distinct change in
performance-this indicates a need for service.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this
Plasma
Monitor
, ask the service technician to perform routine safety
checks to determine that the
Plasma Monitor
is in safe
operating condition.
AC Power Cord has a grounding-type
AC line plug. This is a safety feature to
be sure that the plug will fit into the
power outlet. Do not try to defeat this
safety feature. Should you be unable to
insert the plug into the outlet, contact
your electrician.
Voor de klanten in Nederland
Bij dit product zijn batterijen
geleverd.
Wanneer deze leeg zijn,
moet u ze niet weggooien
maar inleveren als KCA.
GROUND
4
COMPLIANCES
The AC Power Cord supplied with this Plasma Monitor meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada :
AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the
plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be
unable to insert the plug into the outlet, contact your electrician.
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
AC POWER CORD REQUIREMENT
Declaration of Conformity
Model Number : PDP-32H1W
Trade Name : Sanyo
Responsible party : SANYO Manufacturing Corporation
Address : 3333 Sanyo Road, Forrest City, AR 72335
Telephone No. : (870) 633-5030
●This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
GROUND
5
TABLE OF CONTENTS
FEATURES AND DESIGN 6
BEFORE OPERATION 16
COMPUTER MODE 28
VIDEO MODE 32
SETTING 34
APPENDIX 37
PREPARATION 7
NAME OF EACH PART OF PLASMA MONITOR 7
SETTING-UP PLASMA MONITOR 9
CONNECTING PLASMA MONITOR
11
TERMINALS OF PLASMA MONITOR 11
CONNECTING TO VIDEO EQUIPMENT 13
CONNECTING TO COMPONENT VIDEO EQUIPMENT
14
CONNECTING TO COMPUTER 15
OPERATION OF REMOTE CONTROL 16
OPERATING ON-SCREEN MENU 18
SELECTING INPUT SOURCE 28
SELECTING COMPUTER SYSTEM 28
PC ADJUSTMENT 29
SELECTING INPUT SOURCE 32
SELECTING VIDEO SYSTEM 33
SCREEN SAVER FUNCTION 34
SETTING MENU 35
CLEANING THE PLASMA MONITOR 36
TROUBLESHOOTING 37
FUNCTIONS OF PRODUCT SAFETY FEATURES
38
INFORMATION MENU 39
TECHNICAL SPECIFICATIONS 40
BASIC OPERATION 20
TRADEMARKS
● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
● Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its
respective corporation.
TURNING ON / OFF PLASMA MONITOR 20
OFF TIMER 21
SELECTING INPUT SOURCE 22
PICTURE IMAGE LEVEL SELECT 23
IMAGE LEVEL ADJUSTMENT 24
WIDE SCREEN OPERATIONS 25
SOUND ADJUSTMENT 27
6
FEATURES AND DESIGN
This Plasma Monitor is designed with the most advanced technology. The Plasma Monitor utilizes built-in
multimedia features, a palette of 16.77 million colors, and Plasma Display Panel technology.
◆ Compatibility
This Plasma Monitor widely accepts various video and
computer input signals including;
● 6 Color Systems
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PALN color system can be connected.
● Component Video
Component video signals, such as a DVD player
output high definition TV signals including 480i,
480p, 575i, 720p, 1035i or 1080i, can be
connected.
● S-Video
S-Video signals, such as a S-VHS VCR output
signals, can be connected.
● Computers
IBM-compatible and Macintosh computers.
◆ High Definition Plasma Panel
This Plasma Monitor has 852 x 1,024 dots High
Definition Plasma Display Panel. This Plasma Display
Panel has High brightness and wide viewing angle.
◆ Multi-Scan System
This Plasma Monitor has Multi-Scan System to
conform to almost all computer output signals quickly.
There is no need for complicated manual adjustment of
frequency and other settings.
◆ Input Terminals
● D-SUB, RGB input for PC (Up to XGA)
● Component input for DVD
● S-Video / Video for VCR
◆ Dynamic AI (Automatic Image control)
◆ RS232C Terminal
◆ Slim design
● Do not bump or scratch the panel surface as this causes flaws on the surface of the screen.
● Do not display one non-movement still picture on the screen for a long time. Otherwise, an
afterimage or ghost may appear on a part of the panel. To prevent this symptoms, apply the screen
saver function in the Plasma Monitor.
● There may be some tiny black points and/or blight points on the Plasma Display Panel. These points
are normal.
CARE FOR USING PLASMA MONITOR
This Plasma Monitor provides AI (Automatic Imaging
control) circuit which compensates picture contrast and
brightness levels dynamically and reproduces bright and
high-contrast pictures.
This Plasma Monitor can be controlled through
RS232C terminal. It allows you to use other AV systems.
Slim design allows you to get the most advantage. When
installing the Plasma Monitor in limited space, and it is
well designed for easy installation.
7
PREPARATION
NAME OF EACH PART OF PLASMA MONITOR
FRONT
INFRARED
REMOTE RECEIVERS
FRONT CONTROLS
AND INDICATORS
Used to select MENU
operation. (P18)
MENU BUTTON
INPUT BUTTON
MAIN ON/OFF SWITCH
VOLUME BUTTONS
Used to select input source.
(P22)
Used to adjust volume.
(P27)
Used to turn Plasma
Monitor on or off. (P20)
POWER INDICATOR
PLASMA DISPLAY
PANEL
Used to set and adjust the
menu data on On-Screen
Menu. (P18)
CURSOR BUTTON
OK BUTTON
Used to execute the
selected menu on OnScreen Menu. (P18)
Used to select the menu on
On-Screen Menu. (P18)
CURSOR BUTTON
FRONT CONTROLS
Light in green when power is on.
Light in red when power is off with Remote
Control (standby mode), or the Plasma Monitor
is in Power Save mode. (P20)
OK
MENU
INPUT
VOLUME
8
PREPARATION
NAME OF EACH PART OF PLASMA MONITOR
BACK
COOLING FANS
This Plasma Monitor detects
internal temperature and
automatically controls
operating power of Cooling
Fans.
POWER CORD
CONNECTOR
TERMINALS
AND CONNECTORS
(BACK)
TERMINALS
AND CONNECTORS
(SIDE)
SPEAKER OUTPUT
TERMINALS
(RIGHT)
SPEAKER OUTPUT
TERMINALS
(LEFT)
(Refer to page 11)
(Refer to page 12)
For using this Plasma Monitor, Optional Stand or Mounting Bracket is needed. Those optional units are
not included within this Monitor Set. Your Sales dealer can advice you of best optional unit for using
Plasma Monitor. Contact your sales dealer for detail.
NOTES ON USING PLASMA MONITOR
This Plasma Monitor can be installed in
two ways, normal (horizontal) and vertical.
DO NOT INSTALL UNSPECIFIED
DIRECTION, OR COOLING AIR
CIRCULATION IS PREVENTED AND IT
MAY RESULT IN FIRE HAZARD.
INST
ALL PLASMA MONITOR IN PROPER DIRECTION
Front Controls should
be located lower.
Horizontal
Vertical
9
SETTING-UP PLASMA MONITOR
PREPARATION
This Plasma Monitor uses nominal input voltages of 100120 V AC. The Plasma Monitor automatically selects the
correct input voltage. It is designed to work with singlephase power systems having a grounded neutral
conductor. To reduce the risk of electrical shock, do not
plug into any other type of power system.
Consult your authorized dealer or service station if you
are not sure of the type of power supply being in use.
Connect Plasma Monitor with the peripheral equipment
before turning Plasma Monitor on. (Refer to pages 13 ~
15 for connection.)
CAUTION
For safety, unplug the AC Power Cord when the
appliance is not used.
CONNECTING AC POWER CORD
Connect AC Power Cord
(supplied) to
Plasma Monitor.
The AC outlet must be near
this equipment and must be
easily accessible.
NOTE ON THE POWER CORD
The AC Power Cord must meet the requirement of the country where you use the Plasma Monitor.
Confirm the AC plug type with the chart below and the proper AC Power Cord must be used.
If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.
Table Top Stand
When you connect The Plasma Monitor to AC
outlet, attach the supplied ferrite cores. Set the
ferrite cores on the both ends of the AC power
cord . Close the lid tightly until the clamps click.
ATTACHING THE FERRITE CORES
Ferrite cores (supplied)
To the POWER CORD CONNECTOR
on Plasma Monitor
Plasma Monitor side AC Outlet side
Ground
To the AC Outlet.
(120 V AC)
For the U.S.A. and Canada
10
PREPARATION
INSTALLATION OF OPTIONAL SPEAKERS AND STAND
Place the Speakers to each side of the Plasma Monitor
and attach Right and Left brackets with the specified
screws. Mount each screw on proper screw hole position
and fix it securely.
Connect the red wire to the red terminal on both of the
Plasma Monitor and the speakers and connect the black
wire to the black terminal to make correct polarity.
Right Speaker
Assemble Table top stand according to the installation
manual of the stand.
Mount the stand on the back of the Plasma Monitor by
fixing the Arms with screws (3 pcs. for each arm).
● Through installation work, handling with more than two people is recommended.
● When holding (moving or lifting) the Plasma Monitor, hold the Monitor's body. Do not
handle it by holding the attached accessory parts (the Speakers), otherwise damage
could be result.
● Provide space that enough larger than the screen size. The surface must be flat and
maintained with soft material (cloth or blanket) for protecting the screen surface.
● Before placing the Plasma Monitor Screen facing down, make sure there is no object under the screen.
Leaving any object may cause damage on the screen surface.
Please read the each option's instruction manual (or installation manual) for the installation.
CAUTION IN INSTALLATION
SPEAKERS
TABLE TOP STAND
Left Speaker
Speaker Terminal
Red:(+), Black:(-)
Table top stand
Arm
11
CONNECTING PLASMA MONITOR
TERMINALS OF PLASMA MONITOR
This Plasma Monitor has INPUT TERMINALS and OUTPUT TERMINALS on its side and back, for connecting
computers and video equipment. Refer to the figure on pages 13 to 15 and connect properly.
SIDE
When using Remote Control Unit as
Wired Remote Control, Connect
Remote Control Unit to this jack with
Remote Control Cable (supplied).
(Refer to page 17.)
WIRED R/C JACK
Connect Headphone (stereo).
HEADPHONE JACK
When controlling this Plasma
Monitor by computer, connect
your computer to this terminal.
RS-232C TERMINAL
RS-232C
HEADPHONE
WIRED R/C
12
CONNECTING PLASMA MONITOR
Connect analog RGB signal outputs or
component video outputs to these jacks.
Connect analog RGB signal outputs to R,
G, B, HD and VD jacks. (Refer to P15.)
Connect component video outputs to Y,
Pb/Cb and Pr/Cr jacks. (Refer to P14.)
● RGB/COMPONENT (BNC-type)
● AUDIO R and L (RCA-type)
COMPONENT/RGB INPUT JACKS
Connect computer outputs to this
terminals. (Refer to P15.)
● RGB (D-SUB)
● AUDIO R/L (Stereo Mini Jack)
PC INPUT TERMINALS
Connect video and audio outputs from
video equipment. (Refer to P13.)
● S-VIDEO (Mini DIN 4-type)
● VIDEO (RCA-type)
● AUDIO R and L(MONO) (RCA-type)
VIDEO1 INPUT JACKS
MONITOR OUTPUT JACKS
Connect video and audio outputs from
video equipment. (Refer to P13.)
● S-VIDEO (Mini DIN 4-type)
● VIDEO (BNC-type)
● AUDIO R and L (RCA-type)
VIDEO2 INPUT JACKS
BACK
Connect another monitor, video
recorder or external audio amplifier
to these jacks. (Refer to P13~15.)
These jacks are for signals from
VIDEO1 and VIDEO2 INPUT
JACKS only.
● VIDEO (RCA-type)
● AUDIO R and L (RCA-type)
VIDEO1 IN
S-VIDEO
S-VIDEO
VIDEO
VIDEO
VIDEO2 IN
R-AUDIO-L(MONO)
-
AUDIO-L
R
VD HD R B G
VIDEO
R-AUDIO-L
MONITOR OUT
PC IN
Pb /CbPr /Cr
COMPONENT/RGB IN
D-SUB
Y
R
-
AUDIO-L
AUDIO(R/L)
13
CONNECTING PLASMA MONITOR
CONNECTING TO VIDEO EQUIPMENT
Video Source (example)
Video Cassette Recorder Video Disc Player
Video Cable
(RCA x 3)
S-VIDEO
Cable
Audio Speaker
(stereo)
Audio Cable
(RCA x 2)
S-VIDEO
Output
Audio Amplifier
Cables used for connection ( Cables are not supplied with this Plasma Monitor.)
• 21-PIN Video Cable (RCA x 6)
• Video Cable (RCA x 1)
• Video Cable (RCA x 3)
• S-VIDEO Cable
• Audio Cable (RCA x 2)
NOTE :
When connecting Plasma Monitor, AC Power
Cords of both Plasma Monitor and external
equipment should be disconnected from AC outlet.
BNC/RCA
Adapter
(supplied)
External Audio
Equipment
R L
S-VIDEO
VIDEO
R L
Composite Video
and Audio Output
Audio Cable
(RCA x 2)
VIDEO and AUDIO
R/L(MONO)
Video
Cable
(RCA x 1)
Composite Video
and Audio Input
S-VIDEO
S-VIDEO
Output
Composite Video
and Audio Output
Another
Video Source
External Monitor
Video Cable
(RCA x 3)
S-VIDEO
Cable
VIDEO and AUDIO R/L
21PIN
Video Cable
(RCA x 6)
HD R B G
Composite Video/RGB
and Audio Output
R L
Composite video
cable must be
connected on
"HD" terminal.
This composite
signal can not be
displayed on the
screen.
BNC/RCA
Adapters
(supplied)
S-VIDEO
S-VIDEO
VIDEO1 IN
-
AUDIO-L(MONO)
R
VIDEO
VIDEO
-
AUDIO-L
R
VIDEO2 IN
-
AUDIO-L
R
VIDEO
MONITOR OUT
VD HD R B G
Pb /CbPr /Cr
COMPONENT/RGB IN
D-SUB
Y
PC IN
R
-
AUDIO-L
AUDIO(R/L)
14
CONNECTING PLASMA MONITOR
CONNECTING TO COMPONENT VIDEO EQUIPMENT
Component
Video
Source (example)
DVD player
Video Cable
(RCA x 3)
Cables used for connection (Cables are not supplied with this Plasma Monitor.)
• Video Cable (RCA x 3) or (BNC x 3)
• Audio Cable (RCA x 2)
NOTE :
When connecting Plasma Monitor, AC Power
Cords of both Plasma Monitor and external
equipment should be disconnected from AC outlet.
Audio Output
R L
Y
Component video output equipment.
(such as DVD player or
high-definition TV source.)
Audio Cable
(RCA x 2)
Component Video
Output
Video
Cable
(BNC x 3)
Pr/Cr Pb/Cb
or
Audio Speaker
(stereo)
Audio Cable
(RCA x 2)
Audio Amplifier
External Audio
Equipment
R L
BNC/RCA
Adapter
(supplied)
VIDEO1 IN
PC IN
D-SUB
AUDIO(R/L)
S-VIDEO
S-VIDEO
VIDEO
VIDEO
VIDEO2 IN
-
AUDIO-L(MONO)
R
-
AUDIO-L
R
VIDEO
MONITOR OUT
-
R
AUDIO-L
VD HD R B G
Pb /CbPr /Cr
COMPONENT/RGB IN
R
-
Y
AUDIO-L
Loading...