Sanyo MOV-112S, MOV-212S User Manual

INSTRUCTION MANUAL

MOV-112S MOV-212S

Sterilizer

Библиотека Ладовед.

OCR Юрий Войкин 2008г.

MOV-212S

Note:

1. No part of this manual may be reproduced in any form without the expressed written permission of SANYO.

2. The contents of this manual are subject to change without notice.

3. Please contact SANYO if any point in this manual is unclear or if there are any inaccuracies.

CONTENTS

PRECAUTIONS FOR SAFE OPERATION P. 2

CAUTIONS FOR USAGE P. 6

ENVIRONMENTAL CONDITIONS P. 6

STERILIZER COMPONENTS P. 7 INSTALLATION P. 10 BEFORE COMMENCING OPERATION P. 11

OPERATING INSTRUCTIONS P. 12

ALARM & SAFETY FUNCTIONS P. 17

ROUTINE MAINTENANCE P. 18

TROUBLE SHOOTING P. 19 DISPOSAL OF UNIT P. 19

SPECIFICATIONS P. 20

PERFORMANCE P. 20

SAFETY CHECK SHEET P. 21

PRECAUTIONS FOR SAFE OPERATION

It is imperative that the user complies with this manual as it contains important safety advice.

Items and procedures are described so that you can use this unit correctly and safely. If the precautions advised are followed, this will prevent possible injury to the user and

any other person.

Precautions are illustrated in the following way:

WARNING

Failure to observe WARNING signs could result in a hazard to personnel

possibly resulting in serious injury or death.

CAUTION

Failure to observe CAUTION signs could result in injury to personnel and

damage to the unit and associated property.

Symbol shows;

this symbol means caution.

this symbol means an action is prohibited.

this symbol means an instruction must be followed.

Be sure to keep this manual in a place accessible to users of this unit.

< Label on the unit > This mark is labeled on the cover in which the electrical components of high voltage are enclosed to prevent the electric shock.

The cover should be removed by a qualified engineer or a service personnel only.

PRECAUTIONS FOR SAFE OPERATION

WARNING

Do not use the unit outdoors. Current leakage or electric shock may result if the unit is exposed to

rain water.

Only qualified engineers or service personnel should install the unit. The installation by unqualified personnel may cause electric shock or fire.

Install the unit on a sturdy floor. If the floor is not strong enough or the installation site is not adequate, this may result in injury from the unit falling or tipping over.

Never install the unit in a humid place or a place where it is likely to be splashed by water.

Deterioration of the insulation may result which could cause current leakage or electric shock.

Never install the unit under the water main or vapor pipe. Deterioration of the insulation may result which could cause current leakage or electric shock.

(\j Never install the unit in a flammable or volatile location. This may cause explosion or fire.

Never install the unit where acid or corrosive gases are present as current leakage or electric

shock may result due to corrosion.

Use a dedicated power source as indicated on the rating label attached to the unit.

Remove dust from the power supply plug before inserting in a power source. A dusty plug or

improper insertion may pose a hazard.

Use a power supply outlet with ground (earth) to prevent electric shock. If the power supply outlet is not grounded (earthed), it will be necessary to install a ground by qualified engineers.

x~\ Never ground the unit through a gas pipe, water main, telephone line or lightning rod. Such

grounding may cause electric shock in the case of an incomplete circuit.

Do not insert metal objects such as a pin or a wire into any vent, gap or any outlet for inner air

circulation. This may cause electric shock or injury by accidental contact with moving parts.

(\j Never store volatile or flammable substances in this unit. This may cause explosion or fire.

Use this unit in a safe area if using poisonous, harmful or radioactive substances. Improper use may be harmful to your health or the environment.

Disconnect the power supply to the unit prior to any repair or maintenance in order to prevent

electric shock or injury.

PRECAUTIONS FOR SAFE OPERATION

!\WARNING

Ensure you do not inhale or consume medication or aerosols from around the unit at the time of

maintenance. These may be harmful to your health.

Never splash water directly onto the unit as this may cause electric shock or short circuit.

Never disassemble, repair, or modify the unit yourself. Any such work carried out by an

unauthorized person may result in fire or injury due to a malfunction.

Disconnect the power supply plug if there is anything wrong with the unit. Continued abnormal

operation may cause electric shock or fire.

If the unit is to be stored unused in an unsupervised area for an extended period, ensure that children

do not have access and that doors cannot be closed completely.

The disposal of the unit should be undertaken by appropriate personnel. Remove doors to

prevent accidents such as suffocation.

Prepare a safety check sheet when you request any repair or maintenance for the safety of service personnel.

PRECAUTIONS FOR SAFE OPERATION

CAUTION

Select a level and sturdy floor for installation. This precaution will prevent the unit from tipping.

Improper installation may result in water spillage or injury from the unit tipping over.

Connect the unit to a power source as indicated on the rating label attached to the unit. Use of

any other voltage or frequency other than that on the rating label may cause fire or electric shock.

tfB Fix the shelves securely. Incomplete installation may cause injury or damage.

When removing the plug from the power supply outlet, grip the power supply plug, not the cord.

Pulling the cord may result in electric shock or fire by short circuit.

Never damage or break the power supply plug or cord. Do not use the supply plug if its cord is loose. This may cause fire or electric shock.

Do not touch any electrical parts such as the power supply plug or any switches with a wet hand.

This may cause electric shock.

Check the setting when resuming the operation after power failure or switch off. The stocked

materials may be affected if the setting is changed.

Do not put a container with water or heavy articles on the unit. It may cause injury if the articles

fall. Current leakage or electric shock may result form deterioration of insulation by spilled water.

Do not climb onto the unit and do not put articles on the unit. This may cause injury by tipping or

damage to the unit.

Never touch the inside chamber, door glass, exhaust vent or inside of the door when the unit is

operating with high temperature setting as it may cause burn.

Ml Hold the handle when closing the door. This will reduce the likelihood of a trapped finger.

Never place your hand on the glass or use excessive force on the glass. Intentional force may

break the glass resulting in injury from the broken glass.

Do not lean on the door. This may cause injury, current leakage, or electric shock if the unit tips over

or door becomes detached.

Disconnect the power supply plug before moving the unit. Take care not to damage the power cord.

A damaged cord may cause electric shock or fire.

• В Be careful not to tip over the unit during movement to prevent damage or injury.

^^ Disconnect the power plug when the unit is not used for long periods.

(\) Do not put the packing plastic bag within reach of children as suffocation may result.

CAUTIONS FOR USAGE

1. This unit is not explode-proof construction. Never store the materials which cause flammable or volatile gas and never store the flammable or volatile liquid in the unit.

2. The door glass, inside door panel, and exhaust vent are very hot when the unit is used with high

temperature setting. Never touch such portion directly with the hands.

3. Avoid to open the door when the chamber temperature is more than 100°C as it is dangerous. The door opening may cause ignition of flammable material or break of equipment resulting from sudden temperature change.

4. Do not block the air intake vent on the chamber floor by the stocked articles. The blockage can cause unstable chamber temperature and shorten the heater life.

5. When cleaning, do not use brushes, acids, benzine, thinner, soap, cleaner or hot water. These will

cause discoloring or damage to coated surfaces. On plastic or rubber parts, they will cause

transformation, discoloration or degeneration. Never apply volatile chemicals (like benzine etc.) on plastic

or rubber parts. When neutral detergent is used, be sure to wipe it up thoroughly with a wet cloth

afterwards. Before cleaning the box, refer to page 18.

6. When placing objects inside, remove traces of water as much as possible.

7. When stacking the unit, always use stacking kit available as an optional component.

ENVIRONMENTAL CONDITIONS

This equipment is designed to be safe under the following conditions (based on the IEC 1010-1):

1.Indoor use;

2. Altitude up to 2000 m;

3. Ambient temperature 5°C to 35°C

4. Maximum relative humidity 80% for temperature up to 31 °C decreasing linearly to 50% relative humidity at 40°C;

5. Mains supply voltage fluctuations not to exceed ±10% of the nominal voltage;

6. Other supply voltage fluctuations as stated by the manufacturer;

7. Transient overvoltages according to Installation Categories (Overvoltage Categories) II; For mains

supply the minimum and normal category is II;

8. Pollution degree 2 in accordance with IEC 664.

+ 15 hidden pages