SANYO LC86P5632 Datasheet

Ordering number : ENN*6688

CMOS IC

LC86P5632

8-Bit Single Chip Microcontroller

with One-Time Programmable PROM

Preliminary
Overview

The LC86P5632 is a CMOS 8-bit single chip microcontroller with one-time PROM for the LC865600 series.
This microcontroller has the function and the pin description of the LC865600 series mask ROM version, and 32K-byte
PROM.
DIP/QFP package are available for shipping as well as LC865600 series. It is suitable to set up first release, prototyping,
developing and testing of set.

Features

(1) Option switching by PROM data

The option function of the LC865600 series can be specified by the PROM data.

LC86P5632 can be checked the function of the trial pieces using the mass production board.
(2) Internal one-time PROM capacity : 32768 bytes
(3) Internal RAM capacity : 512 bytes

Used PROM or RAM capacity are equal ROM or RAM capacity of mask ROM version which applies LC86P5632.

Mask ROM version PROM capacity RAM capacity

LC865632 32512 bytes 512 bytes
LC865628 28672 bytes 512 bytes
LC865624 24576 bytes 512 bytes
LC865620 20480 bytes 384 bytes
LC865616 16384 bytes 384 bytes
LC865612 12288 bytes 384 bytes
LC865608 8192 bytes 384 bytes

Programming service

We offers various services at nominal charges. These include the ROM writing, the ROM reading, the package stamping
and the screening. Contact our representative for further information.

Ver.1.01
22699

91400 RM (IM) HK No.6688-1/23

LC86P5632

(4) Operating supply voltage : 4.5V to 6.0V
(5) Instruction cycle time : 0.98µs to 400µs
(6) Operating temperature : -30°C to +70°C
(7) The pin and the package compatible with the LC865600 series mask ROM devices
(8) Applicable mask ROM version : LC865632/ LC865628/ LC865624/LC865620/LC865616/
LC865612/ LC865608
(9) Factory shipment : DIP64S, QFP64E

Notice for use

LC86P5632 is provided for the first release and small shipping of the LC865600 series.
At using, take notice of the followings.

(1) A point of difference LC86P5632 and LC865600 series

Item LC86P5632 LC865632/28/24/20/16/12/08
Port form at reset Please refer “Port form at reset “ on next page.
Operation after reset

releasing

Operating supply voltage
range (VDD)
Total output current
[∑IOAH(1)]
[∑IOAH(2)]
Power dissipation
[IDDOP(1)]
[IDDOP(2)]
[IDDOP(3)]
[IDDOP(4)]

• A kind of the option corresponding of the LC86P5632

A kind of option Pins, Circuits Contents of the option

Input/output form of
Input/output ports

Pull-up MOS Tr. Of port7 port7

The port operation related the option is different at reset. Refer to the next table.

The option is specified until 3ms
after going to a ‘H’ level to the reset
terminal by dgrees. The program

The program is executed from 00H of
the program counter immediately after

going to a ‘H’ level to reset terminal.
is executed from 00H of the
program counter.

4.5V to 6.0V 2.7V to 6.0V

Refer to ‘electrical characteristics’ on the semiconductor news.

Port 0
(Specified in a bit)

1. Input : No pull-up MOS Tr.
Output : N-channel open drain

2. Input : P ull-up MOS Tr.

Output : CMOS
Port 1,2
(Specified in a bit)

1. Input : P rogrammable pull-up MOS Tr.
Output : N-channel open drain

2. Input : Pro grammable pull-up MOS Tr.

Output : CMOS
Port 3,4,5
(Specified in a bit)

1. Input : No Programmable pull-up MOS

Tr.

Output : N-channel open drain

2. Input : P rogrammable pull-up MOS Tr.

Output : CMOS

1. Pull-up MOS Tr. not provided

(Specified in a bit)

2. Pull-up MOS Tr. provided

P74

*

has on pull-up resistor option.

No.6688-2/23

LC86P5632

• Port form at reset

Pin Contents of the option LC86P5632 LC865632/28/24 /20/16/12/08

Input : Not pull-up MOS Tr.

P0

Output : N-channel open drain
Input : Pull-up MOS Tr.
Output : CMOS

(Same as the mask version) Input mode without pull-up

MOS Tr. (Output is OFF)

Input mode

•The pull-up MOS Tr. is not provided

Input mode without pull-up

MOS Tr. (Output is OFF)
during reset or several hundred
microseconds after releasing reset.
After that, the pull-up MOS Tr. is
provided. (Output is OFF)

Input : Programmable pull-up

P1,

P2

MOS Tr.

(Same as the mask version) Input mode without pull-up

MOS Tr. (Output is OFF)

Output : N-channel open drain
Input : Programmable pull-up

MOS Tr.

(Same as the mask version) Input mode without pull-up

MOS Tr. (Output is OFF)

Output : CMOS
P3,
P4,

P5

Input : Not Programmable

pull-up MOS Tr.
Output : N-channel open drain
Input : Programmable pull-up

MOS Tr.

(Same as the mask version) Input mode without pull-up

MOS Tr. (Output is OFF)

(Same as the mask version) Input mode without pull-up

MOS Tr. (Output is OFF)
Output : CMOS
Pull-up MOS Tr. not provided (Same as the mask version) Input mode without pull-up

P7

MOS Tr.
Pull-up MOS Tr. provided

Input mode

•The pull-up MOS Tr. is not provided

Input mode without pull-up

MOS Tr.

during reset or several hundred
microseconds after releasing reset.
After that, the pull-up MOS Tr. is
provided.

(2) Option

LC86P5632 uses 256 bytes which is addressed on 7F00 H to 7FFFH in the program memory as option data area . This
area does not affect the execution of program but the program memory capacity of LC865632 is 32512 bytes which is
addressed on 0000H to 7EFFH.
The option data is created by the option specified program “SU865000.EXE”. The created option data is linked to the
program area by linkage loader “L865000.EXE”.

No.6688-3/23

LC86P5632

(3) ROM space

7FFFH
7F00H
7EFFH
6FFFH
5FFFH
4FFFH
3FFFH
2FFFH
1FFFH

Option data

area 256 bytes

Option

Data Area

Option

Data Area

Option

Data Area

Option

Data Area

Option

Data Area

Option

Data Area

0000H

Program area

32K bytes

LC865632

Program area

28K bytes

LC865628

Program area

24K bytes

LC865624

Program area

20K bytes

LC865620

Program area

16K bytes

LC865616

Program area

12K bytes

LC865612

Program area

8K bytes

LC865608

(4) Ordering information

1. When ordering the identical mask ROM and PROM devices simultaneously.
Provide an EPROM containing the target memory contents together with the separate order forms for each of the
mask ROM and PROM versions.

2. When ordering a PROM device.
Provide an EPROM containing the target memory contents together with an order form.

How to use

(1) Specification of option

Programming data for PROM of the LC86P5632 is required.
Debugged evaluation file (EVA file) must be converted to an INTEL-HEX formatted file (HEX file) with file converter
program, EVA2HEX.EXE. The HEX file is used as the programming data for the LC86P5632.

(2) How to program for the PROM

LC86P5632 can be programmed by the EPROM programmer with attachment ; W86EP5032D,
W86EP5032Q.

• Recommended EPROM programmer

Productor EPROM programmer
Advantest R4945, R4944, R4943

Andou AF-9704
AVAL PKW-1100, PKW-3000

Minato electronics MODEL 1890A

• “27512 (Vpp=12.5V) Intel high speed programming” mode available. The addr ess must be set to
“0000H to 7FFFH” and a jumper (DASEC) must be set to ‘OFF’ at programming

(3) How to use the data security function

“Data security” is the disabled function to read the data of the PROM.
The following is the process in order to execute the data security.

1. Set ‘ON’ the jumper of attachment.

2. Program again. Then EPROM programmer displays the error. The error means normally activity of the data
security. It is not a trouble of the EPROM programmer or the LSI.

.

No.6688-4/23

LC86P5632

Notes

• Data security is not executed when the data of all address have ‘FF’ at the sequence 2 above.

• The programming by a sequential operation “BLANK⇒PROGRAM⇒VERIFY” cannot be executed data security at the
sequence 2 above.

• Set to ‘OFF’ the jumper after executing the data security.

Data security

Data security

1 pin mark

of LSI

1 pin

Not data security

1 pin

Not data security

W86EP5032D W86EP5032Q

No.6688-5/23

P11/SI0/SB0

P14/SI1/SB1

P72/INT2/T0IN
P73/INT3/T0IN

Package Dimension

(unit : mm)

3071

P10/SO0

P12/SCK0

P13/SO1

P15/SCK1

P16/BUZ

P17/PWM

TEST1

RES

XT1/

P74
XT2
VSS

CF1
CF2

VDD
P80/AN0
P81/AN1
P82/AN2
P83/AN3
P84/AN4
P85/AN5
P86/AN6
P87/AN7

P70/INT0
P71/INT1

P30
P31
P32
P33

LC86P5632

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33

P07
P06
P05
P04
P03
P02
P01
P00
P27
P26
P25
P24
P23
P22
P21
P20
VDDVPP
VSS
P51
P50
P47
P46
P45
P44
P43
P42
P41
P40
P37
P36
P35
P34

SANYO : DIP-64S(750mil)

No.6688-6/23

LC86P5632

P17/PWM

P16/BUZ

P15/SCK1

P14/SI1/SB1

P13/SO1

P12/SCK0

P11/SI0/SB0

P10/SO0

P07

P06

P05

P04

P03

P02

P01

P00

TEST1

RES

P74

XT1/

XT2
VSS

CF1
CF2

VDD
P80/AN0
P81/AN1
P82/AN2
P83/AN3
P84/AN4
P85/AN5
P86/AN6
P87/AN7

48474645444342

49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64

1

2

3

4

5

414039383736353433

6

7

8

9

10

11

12

13

14

15

32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17

16

P27
P26
P25
P24
P23
P22
P21
P20
VDDVPP
VSS
P51
P50
P47
P46
P45
P44

P70/INT0

P71/INT1

P30

P31

P32

P33

P34

P35

P36

P37

P40

P41

P42

P43

P72/INT2/T0IN

P73/INT3/T0IN

Package Dimension

(unit : mm)

3159

SANYO: QIP-64E

Notes

• The QFP packages should be heat-soaked for 12 hours at 125°C immediately prior to mounting (This baking is called
pre-baking).

• After pre-baking, a controlled environment must be maintained until soldering. The environment must be held at a
temperature of 30°C or less and a humidity level of 70% or less. Please solder within 24 hours.

No.6688-7/23