Sanyo LA4140 Specifications
Ordering number:ENN528D
Monolithic Linear IC
LA4140
0.5W AF Power Amplifier
Features
• Output power 0.5W typ (VCC=6V, RL=8Ω, THD=10%).
• Low quiescent current.
• Wide operating voltage range : V
=3.5 to 12V.
CC
• 9-pin SIP permitting sets to be small-sized and eliminating the need to use a heat sink.
Specifications
Absolute Maximum Ratings at Ta = 25˚C
retemaraPlobmySsnoitidnoCsgnitaRtinU
egatloVylppuSmumixaMV
tnerruCtuptuOmumixaMI
noitapissiDrewoPelbawollA*xamdP 057*Wm
erutarepmeTgnitarepOrpoT 07+ot02–
erutarepmeTegarotSgtsT 051+ot04–
* Pd max : Installed on 50×50mm2 PCB, See figure of Pd max – Ta.
xam
CC
O
Package Dimensions
unit:mm
3017C-SIP9
[LA4140]
1.5
4.8
1.0
1
0.99
edomtnecseiuQ 41V
RedomgnitarepO
61= Ω 41V
L
RedomgnitarepO
8= Ω 21V
L
2.54
22.3
0.5
0.51 min
9
1.3
SANYO : SIP9
3.0
5.7 max
3.2
0.25
1.35
005Am
˚C
˚C
Recommended Operating Conditions at Ta = 25˚C
retemaraPlobmySsnoitidnoCsgnitaRtinU
egatloVylppuSV
ecnatsiseRdaoLR
CC
L
Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft’s
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges,or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
6V
Ω
8
12800TH (KT)/O217KI/4195MW/9300KI, TS No.528–1/5
LA4140
Operating Characteristics at Ta = 25˚C, VCC=6V, RL=8Ω, Rg=600Ω, Rf =47Ω, f=1kHz
retemaraPlobmySsnoitidnoC
tnerruCtnecseiuQI
niaGegatloVGV740525Bd
rewoPtuptuOoP%1=DHT54.05.0V
noitrotsiDcinomraHlatoTDHTWm001=oP3.00.1%
ecnatsiseRtupnIr
egatloVesioNtuptuOV
Equivalent Circuit
OCC
i
IN
k01=gR Ω zHk02otzH05foretlifaiv,4.00.1Vm
sgnitaR
nimpytxam
11Am
k51
tinU
Ω
Notice for Using IC
(1) Maximum Ratings
Enough margin converting supply voltage drifting should be prepared and disigning over maximum ratings
should be absolutely avoided because operation near these ratings causes going across the ratings and leading to
destruction.
(2) Terminating Pins
Turning the circuit on leaving pin to pin of IC shorted causes destruction of failure. Turn on ascertaining that
solder has never shorted pins when setting IC to printed board.
(3) Location
When used in a radio receiver, IC is designed to locate apart from a bar antenua enough.
(4) Printed Pattern Designing
As designing a printed pattern, lines of power supply, output adn ground are to be widely short and pattern and
peripheral parts are considerably set not to feedback from output to input.
Also, a capacitor C8 at power line, C5 and C9 of anti-oscillator are to be arranged near to pins of IC.
Application
No.528–2/5
Loading...