Sanyo FVM3982 Owner's Manual

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit fully into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. If an outside antenna is connected to the television equipment, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. In the U.S. Selection 810-21 of the National Electrical Code provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrodes.

16. An outside antenna system should not be located in the vicinity of overhead power lines or other electrical light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

EXAMPLE OF ANTENNA GROUNDING ACCORDING TO NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

“Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.”

17. Wall or Ceiling Mounting—The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

18. Apparatus shall not be exposed to dripping or splashing, and no objects filled with liquids, such as vases, shall be placed on it.

19. When the MAINS plug is used as the disconnect device, the disconnect device shall remain readily operable.

RISK OF ELECTRIC SHOCK DO NOT OPEN!

CAUTION: TO REDUCE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

FCC INFORMATION ________________________________________________

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

CAUTION: FCC Regulations state that improper modifications or unauthorized changes to this unit may void the user’s authority to

operate the unit.

Please read before operating your HDTV!

PROTECTING THE LCD SCREEN

CAUTION: The screen can be damaged if

it is not maintained properly.

•

Do not use hard objects such as hard cloth or paper to clean the screen.

•

Do not use excessive pressure when cleaning the screen; excessive pressure can cause permanent discoloration or dark spots.

•

NEVER spray liquids on the screen.

HANDLING PRECAUTIONS

•

Handle by the cabinet only.

•

Handling by two or more people is recommended.

•

Never touch the screen when handling.

•

Handling damage is not covered under warranty.

•

Do not remove the protective film covering the front cabinet while handling the HDTV.

POSITIONING THE HDTV

•

Always use a firm and flat surface when positioning your HDTV.

•

Do not position the unit in a confined area.

•

Allow adequate space for proper ventilation.

•

Do not position the HDTV where it is easily reachable by small children and may present risk of injury.

•

Once HDTV is positioned, remove the protective film covering front cabinet.

Wall mounting of the HDTV must be performed by a skilled person.

If stand base disassembly is required:

Place HDTV face down on a padded or cushioned flat surface to protect the screen and finish.

Remove the four (4) screws securing the foot stand. CAUTION: Hold the stand firmly as you remove the last screw.

Use the four (4) screws included in the literature package to secure the HDTV to a wall mounting kit.

NOTE: Wall mounting kit is not included.

VESA standard interface: 200 x 200

Mounting screws measurements:

M6 (6mm) Diameter, Length—12mm (maximum)

WALL MOUNTING (OPTIONAL)

NOTE: Skip these steps if you are wall

mounting the TV.

Place HDTV face down on a padded or cushioned flat surface to protect the screen and finish.

Carefully insert the stand base to the bottom of the HDTV and secure it by inserting four (4) screws as indicated in the diagram below.

NOTE: Stand base screws are located

in the literature package.

Position the HDTV on a firm and flat surface with adequate space for proper ventilation.

STAND ASSEMBLY ______

GETTING STARTED

Install two (2) “AAA” batteries in the remote control. (Not included)

PRECAUTIONS:

• Replace both batteries at the same time. Do not use a new battery with a used battery.

• There’s a risk of explosion if a battery is replaced by an incorrect type.

• Keep away from moisture.

• Be sure to match the “+” and “–” signs on the batteries with marks inside the remote control.

• Please properly dispose of used up batteries.

WARNING: The batteries (or battery pack) shall not be exposed to excessive heat such as sunshine, fire or the like.

BATTERY INSTALLATION

Hook up your antenna or your cable service to the HDTV’s ANT terminal with the use of a 75 OHM coaxial cable.

NOTE: Keep your indoor antenna at

least 3 ft. away from the television set and any other electronic equipment.

The tuner in this HDTV can receive:

• Digital and Analog off air signals

from an antenna

• Analog or ClearQAM cable channels

from a direct Cable TV connection.

ANTENNA CONNECTION FOR OFF-AIR SIGNALS OR CABLE

ANTENNA

CABLE

ANALOG / DIGITAL

ANTENNA IN

AV INPUT SELECTION

Press the INPUT key to select the correct AV input for the video source you wish to watch.

NOTE: Unused AV inputs may be disabled with the Input Setting feature.

Finish Setup

Repeat

Channel Search Result: Succesfully Completed

If you are having problems, call us toll-free at 1-800-877-5032

Analog Channels

Video 1 Video 2 HDMI 1 HDMI 2

Digital Channels16 26

Before proceeding, please make sure to correctly hook up your antenna or cable connection and all AV equipment to your HDTV.

1. PLUG IN AC POWER CORD

120V AC, 60Hz

2. TURN ON TV

3. TV SET LOCATION SELECTION:

Select “Home Mode” to set the HDTV’s backlight to an Energy Star qualified level, or select “Store Mode” to set the backlight to a retail display level.

4. CHANNEL AND SIGNAL SEARCH:

Select “Signal Search” and press ENTER to perform a channel search from an Antenna or a direct Cable connection, and a signal search from devices hooked up to the HDTV’s AV input jacks.

5. SIGNAL SEARCH RESULT SCREEN

The final setup screen displays analog and digital channels found, as well as AV inputs detected.

Select Finish Setup and press ENTER.

NOTE: If you wish to repeat the

process, select Repeat.

INITIAL CHANNEL SEARCH

Need help? www.sanyoctv.com 1-800-877-5032 Need help? www.sanyoctv.com 1-800-877-5032

class

Printed in Mexico, March 2012

US2P / 39-Z6SF / GXBM

Sanyo Manufacturing Corp. 3333

Sanyo Road, Forrest City, AR 72335

This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth.

The American Academy of Pediatrics discourages media use by children younger than two years. For more information, visit www.aap.org.

SPECIFICATIONS

Power Requirement:

Source: AC 120V, 60Hz

AC Power Consumption: 120 watts

Weight: 20 lbs (w/stand)

Dimensions _________________________

WIDTH HEIGHT DEPTH

w/stand 36.7 25.1 8.8

w/out stand 22.8 4.3

NOTE: Dimensions are in inches

SANYO television customers should contact MRM Recycling at 888-769-0149 or visit their website at www.mrmrecycling.com regarding SANYO’s waste management plan.

CONTAINS MERCURY LAMPS, DISPOSE OF PROPERLY

As an Energy Star®Partner, Sanyo Manufacturing Corporation has determined that this product meets the Energy Star

guide-

lines for energy efficiency.

TRADEMARKS ________

Manufactured under license from Dolby Laboratories. “Dolby” is a trademark of Dolby Laboratories.

HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Manufactured under license from Audyssey Laboratories. U.S. and foreign patents pending. Audyssey Dynamic Volume

is a registered

trademark of Audyssey Laboratories.

ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency (EPA). ENERGY STAR is a joint program of the U.S. Environmental Protection Agency and the U.S. Department of Energy helping us all save money and protect the environment through energy efficient products and practices.

Changes to default as-shipped television configuration and settings or enabling certain optional features and functionalities will change the energy consumption of the television, this may increase energy consumption beyond the limits required for ENERGY STAR qualification.

HDTV INPUT/OUTPUT REFERENCE ________________________________________

HDTV BACK PANEL

HDTV SIDE PANEL

HDMI (INPUT1 or INPUT2)

Use HDMI INPUT1 & 2 to hookup HD digital devices such as a Blu-ray player, HD Cable Box, HD Satellite Receiver or Video-game System. Connect your digital device’s HDMI output to any of the two (2) HDMI inputs on your HDTV with the use of an HDMI cable.

NOTE: A DVI connection is possible via the HDMI (DVI) INPUT1

using an appropriate cable or adapter and connecting the audio to the Stereo Mini AUDIO jack.

USB

USB input jack is used to connect a USB mass storage

device to watch digital images stored in JPEG format.

AUDIO mini stereo jack (3.5mm)

For AUDIO signal from DVI device.

Digital Audio Output (Coaxial)

Hookup a multichannel receiver with the use of a phonotype digital audio cable.

Analog / Digital Antenna Input

Hook up your indoor or outdoor digital antenna, or a direct Cable service (Analog or ClearQAM).

VIDEO INPUT2

Green (Y), blue (Pb), and red (Pr) Video inputs plus the white and red Audio inputs.

COMPONENT connection will accept SDTV, EDTV and HDTV video signals. Use it for great image quality from digital devices such as a DVD player or Video Game system.

Match your digital device’s Component output jacks to the Component input jack set (VIDEO2) on your HDTV.

NOTE: A composite connection is possible via VIDEO INPUT2

using the Y (VIDEO) jack and the L/R audio jacks (see Video2 Setting.)

VIDEO INPUT1

Composite yellow (Video), plus white and red (Audio) input jacks.

COMPOSITE connections are used to hookup your analog equipment such as a VCR or an older DVD player.

NOTE: Match the color of your device’s output jack, the

connector and the HDTV’s input jack.

(38.5” diagonal)

1080p HDTV LCD

080p HDTV L

Part No.:

1JC0P1P0017 - -

Model No.:

FVM3982

Owner’s

Manual

(English)

ENERGY STAR

HDMI

DIGITAL

AUDIO

OUTPUT

REMOTE CONTROL OPERATION _______________________________

Channel Scan Memory lists all Analog and Digital channels found. It also lists Analog channels that were not found, which can be added.

Use the CURSOR  keys to move the channel select bar through all enabled and disabled channels.

NOTE: You can use the

 keys to

change page.

Press ENTER to enable or disable the selected channel.

NOTE: For information on local digital channels, visit www.antennaweb.org

Channel Scan Memory

Move SelectENTERPageCH ExitEXITReturnMENU

Analog

Digital

Analog

Digital

03-1

03-2

06-1

WREG-DT

WCVB

WEXT

NICK

VBCT

IMPORTANT FACT: This HDTV maintains only one database of digital channels. Therefore, when you search for cable channels, the database of antenna digital channels will be deleted. You will only be able to receive those ClearQAM channels your cable company provides.

Input Setting feature allows the removal of unused inputs from the AV input loop.

Use the CURSOR  keys to select an AV input. Press ENTER to disable (uncheck) or enable (check) the highlighted input.

NOTE: At least one input must and will remain checked. Unchecked box means the input will be skipped

Input Setting

Channel Setting

Move

Select

ENTER ExitEXIT

ReturnMENU

Channel Search

Channel Scan Memory

Input Setting

Video2 Setting

Video1

Video2

HDMI1

HDMI2

USB

:Skip

Use this feature to establish either a Component or Composite connection to the VIDEO INPUT 2 jacks on your HDTV.

Use the CURSOR  keys to select the type of connection you’ll use in VIDEO INPUT 2.

Press ENTER, a blue mark will appear next to the selected option indicating it as the active option.

Video2 Setting

SETUP

Display the On Screen menu and use the CURSOR keys to select Setup. Press ENTER.

Menu Language

Choose between English, Spanish and French for your On Screen menu’s display language.

Press ENTER on the desired language.

Captioning is textual information transmitted along with the picture and sound. Turning Captioning ON (by pressing the CAPTION key during normal TV viewing) causes the HDTV to open these captions (digital or analog) and superimpose them on the screen.

NOTE: Local broadcasters decide which caption signals to transmit.

Use the CURSOR  and keys to modify Font, Background, and Foreground of digital caption text.

Digital Caption

This feature allows you to set a Current Time for your HDTV and enable a Switch On Time for the HDTV to turn on at a specific time of day.

When On Timer Function is set to ON, the TV will automatically turn on at the previously set Switch on Time.

Use the CURSOR  and keys to modify the Current Time and/or Switch On Time.

Clock Timer

Use this feature to automatically block programs with content you deem as inappropriate for viewing by your children.

NOTE: This feature is designed to com-

ply with the United States of America’s FCC V-Chip regulations. Therefore, it may not function with broadcasts that originate in other countries.

ADJUSTING THE V-CHIP RATINGS

Select ON and press ENTER. Select Adjust (Standard) and press ENTER.

NOTE: Blocking a rating will automati-

cally block all higher ratings. Unblocking a rating will automatically unblock all lower ratings.

For V-Chip (Movie) ratings select Movie and press ENTER, and then select the desired MPAA rating limit. Press the

EXIT key to close the V-Chip menu.

V-Chip (parental control)

For V-Chip (TV) ratings select TV and press ENTER. Use the CURSOR   keys to select a rating and press ENTER. Use the CURSOR   keys to set the rating’s status as Blocked or Viewable. Once ratings are set, press the EXIT key to close the V-Chip menu.

NOTE: Some TV ratings offer more

detailed settings such as Dialogue, Language, Sexual, and Violence.

Setup

Menu Language

V – Chip

Digital Caption

Energy Solution

Clock Timer

Mode (Home/Store)

Off

Adjust (standard)

Move

Select

ENTER ExitEXIT

ReturnMENU

ADVANCED V-CHIP SYSTEM (RRT5)

RRT5 (V-Chip Regional Ratings 5) is an advanced V-Chip ratings system for over the air digital channels. When the HDTV detects compatible RRT5 data, it’s downloaded & stored in memory, and the Setup V-Chip screen is then modified to show the Adjust (Advanced) option.

Use the CURSOR   and keys to highlight the different options, and use the ENTER key to block or unblock the selected rating.

NOTE: When vertical scroll bars appear,

press

CURSOR

 to gain

access to the additional ratings.

MORE INFORMATION

Additional information about MPAA (Motion Picture Association of America) and V-Chip rating can be found at: www.mpaa.org and www.v-chip.org, respectively.

Display the On Screen menu and use the CURSOR keys to select Picture. Press ENTER.

You may choose between Vivid, Mild, and Standard, which have predetermined fixed picture parameter values, or choose the Manual option for customized personal settings.

NOTE: Each AV input can have its

own picture mode (pre-determined or manual.) Current input’s selected option is indicated by a blue marker.

MANUAL PICTURE SETTINGS

Manual parameters to adjust include:

•

Color

•

Tint

•

Contrast • Brightness

•

Sharpness • Color Temperature

The Detailed Setting option allows for the adjustment of several additional parameters such as:

•

Signal Balancer• Noise Reduction

•

White Balance• Edge Enhancer

•

H-Size / V-Size • Dynamic Contrast

Picture

Vivid

Mild

Standard

Manual

Color

Tint

Contrast

Brightness

Sharpness

Color Temperature

Detailed Setting

Default

Move

Select

ENTER ExitEXIT

ReturnMENU

ADJUSTING A PICTURE SETTING

Use the CURSOR  keys to highlight the picture parameter you wish to adjust. Press the ENTER key to enter the value adjustment screen. Modify the selected parameter’s value by pressing the CURSOR keys.

NOTE: CURSOR  keys select the

next/previous parameter without returning to the previous menu screen.

Once adjustments are complete, press the EXIT key to return to normal TV viewing.

Display the On Screen menu and use the CURSOR keys to select Sound. Press ENTER.

Choose sound setting option:

Auto – Sound settings are linked to the current Picture option and parameters are adjusted accordingly.

Dynamic, Mild, Standard – Predetermined sound parameters not linked with any Picture option.

MANUAL SOUND SETTINGS

The Manual option provides different parameters that can be personally adjusted:

•

Bass & Treble

•

Bass Extension

•

Audyssey Dynamic Volume

•

Detailed Setting

– Equalizer: Personalize audio highs

and lows.

Manual

Move

Select

ENTER ExitEXIT

ReturnMENU

Bass

Treble

Bass Extension

Audyssey Dynamic Volume

Detailed Setting

Default Sound

Medium

ADJUSTING A SOUND SETTING

Use the CURSOR  keys to highlight the sound parameter you wish to adjust. Press the ENTER key to enter the value adjustment screen. Modify the selected parameter’s value by pressing the CURSOR keys.

NOTE: CURSOR  keys select the

next/previous parameter without returning to the previous menu screen.

Once adjustments are complete, press the EXIT key to return to normal TV viewing.

Audyssey Dynamic Volume solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. Audyssey Dynamic EQ is integrated into Dynamic Volume so that as the playback volume is adjusted automatically, the perceived bass response, tonal balance, surround impression and dialog clarity remain the same.

NOTE: A thumbnail hide icon will appear if a picture cannot be decoded or if no thumbnail data is available.

View pictures on your HDTV with the use of a USB mass storage device (not included.)

USB FLASH

DRIVE

PHOTO VIEWER

USB INPUT

USING THE PHOTO VIEWER

Press ENTER on a thumbnail photo to enable the Rotate, Full View and Start Slideshow functions.

Once in Full View mode: Use the CURSOR keys to change

picture.

Press ENTER to show the full view options menu.

•

Rotate

•

Zoom In / Out

•

Pan

•

Slideshow setup

•

Start Slideshow• Browse Photo

SLIDE SHOW

In the Slideshow Setup menu you may turn the Shuffle and Quick Change options ON or OFF.

Press ENTER on Start Slideshow either from the Thumbnail View Screen or from the full view options menu to start the slideshow from the current picture.

V-Chip (continued)

HDTV SIDE PANEL

Your Sanyo HDTV is registered at the time of purchase,

please keep sales receipt for future reference.

For your protection in the event of theft or loss of this product, please fill in the information requested below and KEEP IN A SAFE PLACE FOR YOUR OWN PERSONAL RECORDS.

Model No. ______________________ Serial No. _____________________________

Purchase date ___________________ Purchase Price _________________________

Where Purchased _________________________

(Located on back of unit)

ONE-YEAR LIMITED PARTS AND LABOR

WARRANTY

THIS LIMITED PARTS AND LABOR WARRANTY IS VALID ONLY ON SANYO TELEVISIONS PURCHASED AND USED IN THE UNITED STATES OF AMERICA, CANADA, AND PUERTO RICO, EXCLUDING ALL OTHER U.S. TERRITORIES AND PROTECTORATES. THIS LIMITED WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL PURCHASER, AND DOES NOT APPLY TO PRODUCTS USED FOR INDUSTRIAL OR COMMERCIAL PURPOSES.

WARRANTY APPLICATION

FOR ONE YEAR from the date of original retail purchase Sanyo Manufacturing Corporation (SMC) warrants this TV to be free from manufacturing defects in materials and workmanship under normal use and conditions for parts and labor.

For the FIRST 90 DAYS from the date of original retail purchase, Sanyo Manufacturing Corporation will replace any defective TV via exchange at the retailer. To ensure proper

warranty application, keep the original-dated-sales receipt for evidence of purchase. Return the defective TV to the retailer along with the receipt and the included accessories, such as the remote control. The defective TV will be exchanged for the same model, or a replacement model of equal value, if necessary. Replacement model will be contingent on availability and at the sole discretion of Sanyo Manufacturing Corporation.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

OBLIGATIONS

For one year

from the date of purchase, Sanyo Manufacturing Corporation warrants this product to be free from defects in material and workmanship under normal use and conditions. During the first 90 days under this warranty for any manufacturing defect or malfunction Sanyo Manufacturing Corporation will provide a new TV via exchange at the retailer.

HOW TO MAKE A CLAIM UNDER THIS WARRANTY

Please call 1-800-877-5032. Please be prepared to give us the television’s model number and serial number when you call. The model number and serial number are printed on a

label attached to the back of the unit.

For customer assistance, call toll free 1-800-877-5032.

This warranty expresses specific contractual rights; retail purchasers may have additional statutory rights which vary from state to state.

(EFFECTIVE: March 1, 2007)

(Located on back of unit)

PICTURE

SOUND

POWER. Turns your HDTV On or Off.

INPUT. Selects the video source to

view. Holding down the key displays the Input List.

ECO. Modifies the Energy Saver level.

AUDIO. Selects the desired Audio

mode. Stereo, Mono, or SAP (when available.)

ON TIMER. Displays the current switch on time (if activated.)

CAPTION. Cycles through the available Caption modes (when available.)

RESET. Pressing it twice restores your HDTV to its factory settings. All user customized settings will be cleared.

SLEEP. Displays the “Off” Timer. While Off Timer is on-screen, press the “0” key to Set the amount of time (in 30 minute increments) at which the HDTV will turn off.

NUMERIC KEYS. Choose a channel directly.

CH . Scan through the channels in the memory database.

VOL +

––

. Increases or decreases the

audio level.

RECALL. Switch between current chan- nel and last selected channel or input.

SUB CH. Use for the direct selection of digital subchannels. For example: for channel 39.1 press the

3 and 9 keys,

followed by the dash

––

, and 1 keys.

MUTE. Mute or restore the sound.

INFO. Displays the Channel Information

banner.

PIX SHAPE. Cycles through the various aspect ratios. The different settings either stretch, zoom, or fill the image on your screen. Bars may appear on top and bottom of your screen (or on left and right sides) depending on the broadcasted signal or program.

DYN VOL. Modifies the Dynamic Volume feature settings

MENU. Displays or the on-screen menu. Use as “back” key in menu navigation.

HELP. Displays the on-screen Help menu.

CURSOR

. Move the on-screen

cursor in the desired direction.

ENTER. Set or confirm selected option.

EXIT. Exits the on-screen menu.

Auto – Searches the detected mode,

Cable or Air.

Cable – Searches for analog and unscrambled (ClearQAM) digital cable channels.

Air (Antenna) – Searches for analog and digital off-air channels.

Digital Add-On – Searches digital channels adding newly found digital channels to the channel database.

Channel Search

Display the On Screen menu and use the CURSOR  keys to select

Channel Setting. Press ENTER.

ON-SCREEN MENU OPERATION

CHANNEL

Energy Solution

ECO (ENERGY SAVER)

ECO controls the LCD backlight brightness to reduce power consumption.

– Level 1: Energy Saver feature is off. – Level 2: Low power consumption. – Level 3: Lowest power consumption.

Press ENTER on the desired level.

LIGHT SENSOR

This feature detects ambient room light brightness and uses that reading to control the panel brightness level and picture parameters to reduce the HDTV’s power consumption.

NOTE: When room lighting is dark,

the panel brightness and/or the picture setting parameters such as brightness and contrast are lowered. When room lighting is bright, parameters are affected opposite.

Use the CURSOR  keys to select On or OFF and press ENTER.

AUTO SHUT-OFF

When Auto Shut-off feature is set to ON, it will allow the HDTV to automatically turn off when no video and/or audio signals are being received.

NOTES: By factory default, this fea-

ture is set to ON. The HDTV will automatically turn off if no AV signals are received in a time span of 15 minutes.

Use the CURSOR  keys to select On or OFF and press ENTER.

Use the Mode (Home/Store) option if you would like to change the initial Energy Saving Mode chosen at HDTV’s first power on.

Home Mode - For saving energy and power consumption reduction.

Store Mode - High brightness and contrast for display at retailer store.

NOTE: Only Home Mode qualifies for Energy Star.

Press ENTER on the desired mode.

Mode (Home/Store)

Insert the flash drive into the USB port, the TV will display the Photo Viewer screen, select Shuffle Play or Browse Photos and press ENTER to begin.

ECO ONTIMER

SUB CH

INFO DYN VOL