Sanyo EDD-T1550 Owners Manual

OWNER'S MANUAL

ECD-T1550

• PLL Synthesizer Stereo Radio

• Digital Compact Disc Player

• Automatic Memory Storing

• Motorized Hidden Panel

• Preset Equalization

• Auxiliary Input Jack

• Credit Card Remote Control

• Multi-Color LCD

• Plays CD-R/RW discs

CONTENTS

Installation......................................3

Take out screw before installation ...3

DIN Front-Mount (Method A)...........3

Installing the unit ..........................3

Removing the unit ........................4

DIN Rear-Mount (Method B)............5

Using the front panel.....................6

Wiring Connection.........................7

Operation........................................8

Switching on/off the unit..................9

Faceplate release ............................9

Sound adjustment ...........................9

Loudness .........................................9

Set the clock....................................9

Mute ................................................9

Equalization .....................................9

Liquid crystal display.......................9

Flashing LED ...................................9

Remote sensor ...............................9

Reset function .................................9

Radio operation ...............................10

Switching to radio mode ..............10

Selecting the frequency band ......10

Selecting station ..........................10

Local/distant ................................10

Automatic memory storing&

program scanning ........................10

Station storing..............................10

Mono/stereo.................................10

CD operation ...................................10

Switching to CD mode .................10

Selecting tracks............................11

Pausing playing............................11

Previewing all tracks ....................11

Repeating the same track ............11

Playing all tracks in random.........11

Ejecting a disc..............................11

Disc notes........................................11

Specification....................................12

Trouble shooting ..............................13

INSTALLATION

Notes:

• Choose the mounting location where the unit will not interfere with the normal activity of the driver.

• Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly. Test to see if the system is working properly.

• Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.

• Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.

• Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop.

• If installation angle exceeds 30˚ from horizontal, the unit might not give its optimum performance.

30˚

• Avoid installing the unit where it would be subject to high temperature, such as direct sunlight, hot air from the heater, or where it would be subject to dust, dirt or excessive vibration.

DIN FRONT/REAR-MOUNT

This unit can be properly installed either from “Front” (conventional DIN Frontmount) or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods.

TAKE OUT SCREW BEFORE INSTALLATION

Before install the unit, please remove the two screws.

Take out screw before installation

DIN FRONT-MOUNT (Method A)

Installation Opening

This unit can be installed in any dashboard having an opening as show below:

53 mm

182 mm

Installing the unit

Be sure you test all connections first, and then follow these steps to install the unit.

1. Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery's negative (-) terminal.

2. Disconnect the wire harness and the antenna.

3. The two supplied keys release tabs inside the unit's sleeve so you can remove it. Insert the keys as far as they will go (with the notches facing up) into the appropriate slots at the middle left and right sides of the unit. Then slide the sleeve off the back of the unit.

INSTALLATION

Sleeve

L Key

R Key

4. Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective. Bend open the appropriate tabs behind the dashboard to secure the sleeve in place.

Dashboard

Tabs

Screwdriver

5. Reconnect the wire harness and the antenna and be careful not to pinch any wires or cables.

6. Slide the unit into the sleeve until it locks into place.

7. To further secure the unit, use the supplied metal strap to secure the back of the unit in place. Use the supplied hardware (Hex Nut (M5mm) and Spring Washer) to attach one end of the strap to the mounting bolt on the back of the unit. If necessary, bend the metal strap to fit your vehicle's mounting area. Then use the supplied hardware (Tapping Screw (5x25mm) and Plain Washer) to attach the other end of

metal strap to a solid metal part of the vehicle under the dashboard. This strap also helps ensure proper electrical

grounding of the unit.

Spring Washer

Metal Strap

Mounting Bolt

Hex Nut

Plain Washer

Tapping Screw

8. Reconnect the cable to the vehicle battery's negative (-) terminal.

Removing the unit

1. Make sure the ignition is turned off, then disconnect the cable from the vehicle battery’s negative (-) terminal.

2. Remove the metal strap attached the back of the unit (if attached).

3. Insert the release frame key into the groove at the right side of the frame, then prize out to remove the frame. (You can also use the key to remove the frame from the left side.)

Frame

4. After releasing the frame, insert the release unit keys supplied with the accessory into the grooves at both sides of the unit as shown in figure until they click. Pulling the keys makes it possible to remove the unit from the dashboard.

INSTALLATION

DIN REAR-MOUNT (Method B)

Ta b

1. Factory-installed radio bracket

2. Car radio mounting bracket

3. Screw

4. After aligning the car radio mounting bracket with the factory-installed radio bracket, tighten the screws (M5x4mm) at 2 places on each side.

5. When fixing factory-installed radio bracket with the screws, use a standard-tipped screwdriver to pry the tabs of the car radio mounting bracket to make them fit into the holes in the factory-installed radio bracket.

6. Movable panel frame

+ 11 hidden pages