Sanyo ECD-T1560 User Manual

ECD-T1560

SIRIUS SATELLITE RADIO OPERATING MANUAL

MOD

50W x 4

ECD-T1560

MANU/SKIP/CH

LOUD/ENT/ENT

BAND

DSP

AUX INMONMUTLOC/S-MOD

VOLUME A-Z/0-9

SEL

SET

P.SCN/MP3

AS/PS

RPT

PAU

SCN

SHF

CAT/DIR

DISC6 DISC

Motorized Stealth Panel High Power FM/AM Stereo Receiver Compact Disc Player/MP3 Player/With ESP ISO Mounting with Removable Trim Ring Sirius Function Remote Control CD-R/RW Compatibility

(English)

SIRIUS OPERATION……………. 2~3

SIRIUS OPERATION

MOD

50W x 4

ECD-T15 60

MANU/SKIP/CH

LOUD/ENT/ENT

BAND

DSP

AUX INMONMUTLOC/S-MOD

VOLUME A-Z/0-9

SEL

SET

P. S C N/ M P 3

AS/PS

PAU

RPT

SCN

CAT/DIR

SHF

DISC6 DISC

SWITCHING TO SIRIUS MODE……………………..…(1)

Press MOD button (1) to select Sirius mode.

SELECTING USER-PRESET CHANNEL……………..(2)

At Sirius mode, the Sirius user-preset channel group (3 groups) is toggled cyclically through the

group by quickly pressing the BAND/LOUD/ENT button (2).

The channel will change in the following order:

SR1 SR2 SR3

SELECTING CHANNEL UP/DOWN……………………(3)

Press the MANU/SKIP/CH or button (3) to select the channel up or down.

SEARCHING STATION…………………………….……(4)

When the AS/PS/P.SCAN/MP3 button (4) is pressed, the channel searches for each user preset

station from SR1 to SR2 to SR3.

When an available channel is detected, the station will be held at that preset number and play for

5 seconds. After that, it will mute and search for another available station

STORING PRESET STATIONS ..........................….....(8)

The preset buttons (8) can be used to store 6 stations for convenient access to your favorite

stations.

• Programming stations ..... 1. Select the desired station you want to store in memory.

2. Press and hold one of the preset buttons (8) for more than 2

seconds until the corresponding preset button number appears.

Repeat steps 1. and 2. to program additional stations.

• Quick tuning .................... Press one of the six preset buttons (8) shortly to select a preset

station directly.

SIRIUS MODE SELECTION .........….............…….…..(5)

Press LOC/S-MOD button (5) to switch Category mode, Skip mode or normal. It is used as the

selection of each:

Normal Category mode Direct Tune Skip Channel mode

When Category mode or Skip mode is engaged, the “CATEGORY” or “SKIP” function is turned

on in the display. When Category mode or Skip mode is released, the “CATEGORY” or “SKIP”

function is turned off. When Direct mode is engaged, “DIRECT” of alphanumeric display is turned

on.

Select Category and TUNE UP/DOWN within selected Category

Use CAT/DIR button (7) or CAT/DIR button (6) to select desire Category and press

BAND/LOUD/ENT button (2).

In Category mode, stations can be tuned within the same category.

- When the user wishes to search by Category, press LOC/S-MOD button (5) can be pressed

until it goes into Category search mode.

- Press CAT/DIR

category.

- To change channels, press LOC/S-MOD button (5) again to Normal mode, and then press

MANU/SKIP/CH

button (7) or CAT/DIR button (6) up and down to get to the desired

or button (3) to select the channel up or down.

The operation of skip channel function

In Skip mode, pressing LOC/S-MOD button (5) for more than 3 seconds sets the SKIP channel

mode. Details for set or release skip channel is as follows.

Use MANU/SKIP/CH

mode sequentially.

- Press BAND/LOUD/ENT button (2) to select skip or release the following channel. (If the

channel was skipped, the “SKIP” icon will be displayed.

- Press LOC/S-MOD button (5) for more than 3 seconds again to return to basic mode

automatically after 10 seconds.

Note:

In skip mode, use MANU/SKIP/CH or button (3) to show skipped channels.

or button (3) to be switched to SKIP channel set or release

How to direct tune

1. In direct mode, display shows DIRECT and “000” channel number. (Hundred Digit flashing

on/off)

2. Use MANU/SKIP/CH

3. Press LOC/S-MOD button (5) again to confirm entry of the hundred digit and the 10s digit is

flashing on/off.

4. Use MANU/SKIP/CH

5. Press LOC/S-MOD button (5) again to confirm entry of the 10s digit and the 1s digit is

flashing on/off.

6. Press LOC/S-MOD button (5) again to confirm entry of the 1s digit.

7. Press BAND/LOUD/ENT button (2) to direct tune.

or button (3) to select hundred digit.

or button (3) to select 10s digit.

ECD-T1560

MOD

50W x 4

ECD-T1560

MANU/SKIP/CH

LOUD/ENT/ENT

BAND

DSP

AUX INMONMUTLOC/S-MOD

VOLUME A-Z/0-9

SEL

SET

P.SCN/MP3

AS/PS

RPT

PAU

SCN

SHF

CAT/DIR

DISC6 DISC

Motorized Stealth Panel High Power FM/AM Stereo Receiver Compact Disc Player/MP3 Player/With ESP ISO Mounting with Removable Trim Ring Sirius Function (see separate booklet on Sirius Radio operation) Remote Control CD-R/RW Compatibility

(English)

OPERATING INSTRUCTIONS……………. 2~27

CONTENTS

COMPACT DISC CARE ...........................................................................................................3

DIGITAL DISPLAY .....................................................................................................................4

DETACHABLE FRONT PANEL .................................................................................................5

GENERAL OPERATION ............................................................................................................6

RADIO OPERATION..................................................................................................................8

CD OPERATION ........................................................................................................................10

CDC OPERATION .....................................................................................................................12

MP3 OPERATION......................................................................................................................14

MIXED-CD OPERATION ...........................................................................................................17

AUX MODE OPERATION ..........................................................................................................18

REMOTE CONTROL .................................................................................................................19

ERROR SIGNS ..........................................................................................................................20

HINTS FOR PROPER AND SAFE OPERATION ......................................................................21

TROUBLE SHOOTING .............................................................................................................. 22

ACCESSORIES AND HARDWARE...........................................................................................23

INSTALLATION..........................................................................................................................23

UNIT REMOVAL ........................................................................................................................24

ELECTRICAL CONNECTIONS .................................................................................................25

LINE OUT CONNECTIONS .......................................................................................................26

AUXILIARY INPUT CONNECTIONS .........................................................................................26

CAUTION

• This unit is designed to operate on 12 volts DC, NEGATIVE ground electrical systems only.

• When fuse replacement is necessary, use only a 15 amp fuse. Do not replace with a higher

rated fuse. If the fuse blows often, carefully check all electrical connections for any short

circuits and have your car’s voltage regulator checked also.

• Do not install the unit where it will be exposed to direct sunlight or hot air discharged from the

car heater.

• Do not expose the unit to water or moisture.

• To avoid damaging the unit, never insert anything other than a compact disc into the disc slot.

• This unit should not be adjusted or repaired by anyone except qualified service personnel.

If servicing is required, return the unit to an authorized SANYO mobile audio dealer.

• Use the Controls or adjustments or performance of procedures other than those specified

herein may result in hazardous radiation exposure.

• Changes or modifications not expressly approved by SANYO may void the user’s authority to

operate this equipment.

COMPACT DISC CARE

Dirt, dust, scratches and warpage can cause deterioration in the sound or intermittent skipping some tracks during play.

TEXT

ReWritable

• This unit has been designed to play compact discs bearing the identification logo shown on the left. No other discs can be played.

• Do not use non-conventional discs such as heart- shaped, octagonal discs, etc. The player could be damaged.

Recommended CD-R/RW Media

Data may not be properly written to CD-R/RW media depending on the quality of the media. If this happens, the data may not be reproduced correctly. We recommend the following manufacturers to insure proper quality of the media.

CD-R Media

TDK USA Corp., Taiyo Yuden (U.S.A.), Inc., Ricoh Corporation, Eastman Kodak Company, Maxell Corporation of America, Mitsubishi Chemical Corporation, Fuji Photo Film U.S.A., Inc., Mitsui Chemicals, Inc., Sony Corporation of America, Philips Electronics North America Corporation, Imation Corp.

CD-RW Media

TDK USA Corp., Ricoh Corporation, Mitsubishi Chemical Corporation.

Additionally, CD-R media compatible with various speeds such as 2X and 1X-4X are available. Please refer to the instruction manuals of the drive and the recording software you are using to selection of the correct media.

• Fingerprints and dust should be carefully wiped off the signal surface of the disc (glossy side) with a soft cloth. Wipe in a straight motion from the inside to the outside of the disc. Unlike conventional records, the compact disc has no grooves to collect dust and debris. Small dust particles will have no effect on reproduction quality.

• Do not insert a disc which is cracked into the unit.

• Do not apply paper or write anything on the surface of the disc.

• To prevent warping the disc, do not expose it to direct sunlight, high humidity or high tem

eratures for extended periods of time.

• Never use chemicals such as record cleaning sprays, antistatic sprays or fluids, benzene or thinner to clean compact discs. These chemicals will permanently damage the plastic surface of the disc.

• When not using the disc player for extended periods of time, remove the compact disc and return it to the plastic storage case. This will protect the disc from dust and exposure to

the sun.

DIGITAL DISPLAY

Radio Frequency, Time, CD Track Number, Audio Control

CD-IN indicator

Selected Mode

SAT

Stereo

Local

Channel name indicator

CLASSIC

SAT

POP

Channel name

ROCK

Category

Mono

Skip

Artist

Loud

Subwoofer

Song title

USING THE FRONT PANEL

1. When the ignition key is switched to “ACC

ON”, the panel of the unit will change from State 1 to

State 2, the hidden panel will turn up.

2. Press (power) button to turn on the unit. Then

press

horizontal position (see State 3).

3. Insert a disc in the disc slot, the panel will automatically turn up to State 2. Press

button again, the panel will turn down to eject the disc. If you don’t insert a disc in again, the

panel will automatically turn up in about 10 seconds. If you don’t want to wait, press

button, the panel will also turn up.

4. When the ignition key is switched to “ACC OFF”, the front panel will change from State 2 to

State 1 if there is nothing plugged into the AUX IN jack.

If there is a portable audio player connected to the unit through the AUX IN jack, the front

panel will remain State 2.

(eject) button, the panel will turn down to

(eject)

RETURNING TO THE INITIAL SETTINGS

When the front panel is open, you can find the RESET button on the top right corner of the panel. Press the button, the Microcomputer of the unit returns to the initial settings. If the display window is not properly shown or the unit malfunctions, press the RESET button.

Reset button

GENERAL OPERATION

MOD

50W x 4

ECD-T1560

MANU/SKIP/CH

LOUD/ENT/ENT

BAND

DSP

AUX INMONMUTLOC/S-MOD

VOLUME A-Z/0-9

SEL

SET

P. S C N / M P3

AS/PS

PAU

RPT

SCN

CAT/DIR

SHF

DISC6 DISC

TURNING THE POWER ON........................Any button

When the hidden panel turns up (in State 2), switch on the unit by pressing any button (except

button).

TURNING THE POWER OFF ...............................….. (1)

When system is on, press the button (1) to turn off the unit.

VOLUME LEVEL CONTROL.......................................(2)

Rotate the VOLUME dial (2) to adjust the volume level.

ADJUSTING THE SOUND

CHARACTERISTICS ..................................…......(2), (3)

Press the SEL/SET button (3) shortly:

1. Each time you press the SEL/SET button (3) shortly, the item changes as follows;

VOL BAS TRB BAL FAD

(Volume) (Bass) (Treble) (Balance) (Fader)

2. Rotate the VOLUME dial (2) to adjust the selected item. Make the adjustment within 5

seconds after selecting. After 5 seconds, the display window will revert to display priority.

Adjustment Range

BASS (BAS 00)

TREBLE (TRB 00) TRB –10 TRB 10

BALANCE (BAL L=R)

FADER (FAD F=R)

BAS –10 BAS 10

10L 10R

10F 10R

Beep Sound Adjustment:

Press and hold the SEL/SET button (3) for several seconds to enter beep sound adjustment

mode, then rotate the VOLUME dial (2) clockwise or counter-clockwise to select as follows:

BEEP 2ND BEEP ALL BEEP OFF

- BEEP 2ND mode:

The beep is only generated when all allowed double function button is pressed for several

seconds.

e.g.

When preset button is pressed.

When BAND/LOUD/ENT button is pressed.

When AS/PS/P.SCAN/MP3 button is pressed.

- BEEP ALL mode:

The beep is generated when every button is pressed.

- BEEP OFF mode: The beep is disabled.

MODE SELECTION...................................……..….....(4)

Press MOD/SW button (4) to choose desired listening mode. (e.g. radio mode to SIRIUS mode

to CD (MP3) mode to CDC (or AUX) mode)

SUBWOOFER FUNCTION...........................…...….....(4)

Press MOD/SW button (4) for several seconds to toggle sub-woofer output. Press it for several

seconds again to release this mode.

DISPLAY INFORMATION..................………………....(5)

When pressed quickly, the DSP button (5) changes the display as follows.

- In AM/FM mode:

-> Frequency ->CLOCK ->

- In Sirius mode:

-> Channel Name -> Song Title -> Artist Name -> Category Name -> CLOCK ->

- In CD mode:

-> CD ->CLOCK ->

- In CDC (or AUX) mode:

-> CDC (or AUX) ->CLOCK ->

Each display time is 5 seconds, the display will return to the first position after 5 seconds.

SET THE CLOCK……………............................(5),(8),(9)

Press the DSP button (5) to show the clock on the LCD display. Then hold the button until the clock flashes. During this mode, press the MANU/SKIP/CH button (8) to change hours or

MANU/SKIP/CH

button (9) to change minutes.

LOUDNESS EFFECT...................................……..…..(6)

Press BAND/LOUD/ENT button (6) for several seconds to reinforce the bass output. Press it for

several seconds again to release this function.

EQUALIZATION......................……............…………..(7)

Press EQ button (7) to turn on equalization function and to select desired audio mode. There are

five kinds of modes as below:

FLAT CLASSICS POP M ROCK M DSP OFF

MUTE FUNCTION...................................……..….…(10)

Press MUT button (10) to mute down the sound instantly. If any button is pressed in the mute

state, the mute state is released.

ESP FUNCTION

The unit has the electronic shockproof function. It can be shockproof for more than 20 seconds.

+ 21 hidden pages