Sanyo DVD-SL20V Service Manual

FILE NO.

Service Manual

CONTENTS

DVD Video Player

DVD-SL20V

PRODUCT CODE No. 137 114 09

REFERENCE No. SM5810309

Specification ..................................................................... 1

Laser beam safety precaution .......................................... 1

DVD Mechanism replacement ......................................... 2

Mechanism Replacement ................................................ 3

Trouble shooting .............................................................. 5

Service mode ................................................................... 7

How to load software for MPEG P.W.Board .................... 10

Exploded View (Cabinet & Chassis) ................................ 11

Parts List .......................................................................... 12

Exploded View (DVD Mechanism) ...................................15

Parts List .......................................................................... 15

IC Block Diagram & Description ....................................... 16

Wiring Connection ............................................................ 33

Block diagram (DVD back end) ........................................ 32

(KR)

STANDBY

REMOTE CONTROLLER RB-SL20

NEXTPREV

FWD SLOWREV SLOW

PAUSE/STEP

PLAY

REV FWD

CLEAR

MODE

123C

456

789

ENT

SETUP MENU

AUDIO TITLE RETURN

PICTURE

MODE

ANGLE

REPLAY

ZOOM ANGLE

LAST MEMO

SURROUND

ON SCREEN

PROGRAM

OPEN/CLOSE

REPEAT A-B REPEAT

SUBTITLE CHANGE

SUBTITLE

ON/OFF

Schematic Diagram (DVD) ............................................... 34

Schematic Diagram (MPEG) ............................................ 36

Wiring Diagram (DVD & MPEG A side) ......................... 38

Wiring Diagram (DVD & MPEG A side Top Left) ........... 40

Wiring Diagram (DVD & MPEG A side Bottom Left) ......42

Wiring Diagram (DVD & MPEG A side Top Right) ......... 44

Wiring Diagram (DVD & MPEG A side Bottom Right) ... 46

Wiring Diagram (DVD & MPEG B side) ......................... 48

Wiring Diagram (DVD & MPEG B side Bottom Left) ......50

Schematic Diagram (FRONT & DENGEN) ...................... 52

Wiring Diagram (DENGEN and FRONT) ....................... 54

Wiring Diagram (MECHA-SW) .......................................56

Wiring Connection ........................................................... rear

- 1 -

SPECIFICATIONS

Playback system:

DVD-Video, CD

Playback standard:

PAL or NTSC

Laser:

Semiconductor laser, wavelength: 650/790 nm Laser output (Continuous wave max.):

1 mW (DVD)

0.5 mW (CD)

Frequency range (digital audio):

4 Hz to 44 kHz (DVD fs: 96 kHz)

Signal to noise ratio:

More than 105 dB

Harmonic distortion (digital audio):

0.003 %

Wow and flutter:

Below measurable level

Outputs:

DIGITAL OUT:

For optical cable

AV EURO CONNECTOR:

For Euro-AV cable

S-VIDEO OUT:

Y: 1.0 Vp-p (75 Ω) NTSC, 1.0 Vp-p (75 Ω) PAL C: 0.286 Vp-p (75 Ω) NTSC, 0.3 Vp-p (75 Ω) PAL

VIDEO OUT:

1.0 Vp-p (75 Ω)

LASER BEAM SAFETY PRECAUTION

• Pick-up that emits a laser beam is used in this CD player section.

CAUTION :

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE

LASER OUTPUT..........0.6 mW Max. (CW)

WAVELENGTH .............790 nm

VIDEO OUT

AUDIO OUT

Y C

R L

COMPONENT VIDEO OUT

DIGITAL OUT

OPT.

S-VIDEO OUT

VIDEO OUT SELECT

COMPONENT

CAUTION – INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.

ADVARSEL – USYNLIG LASER STRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION, UNDGÅ UDS ÆTTELSE FOR STRÅLING.

VARNING – OSYNLIG LASER STRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRR ÄR URKOPPLAD. STRÅLEN ÄR FARLIG. VORSICHT – UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN DECKEL GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT IST. NICHT, DEM STRAHL AUSSETZEN.

VARO – AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

AUDIO OUT:

L: 2 V rms R: 2 V rms

Power requirements:

AC 220 V, 60 Hz

Power consumption:

13 W Less than 2 W (standby mode)

Dimensions:

360(W) x 63.5(H) x 250(D) mm

Weight:

2.1 kg

This is a basic specifications. Specifications subject to change without notice.

- 2 -

1. Cautionary instructions in handling the assy (Safety instructions) Optical pickup The laser beam used in the pickup is classified as "class 2". Exposing your eyes or skin to the beam is harmful. Take care not to do so.

(Caution against static electricity and leakage voltage) Ground securely the work tables, tools, fixtures, soldering irons (including those made of ceramic) and measuring instruments used in the production lines and inspection departments that handle loaders. The workers shall also be grounded.

(Cautionary instructions in handling) Do not touch the object lens when handling a loader, or the lens will be stained, resulting in inadequate playability. There is no power supply protection circuit provided for this product or adjustment/inspection device. Short-circuiting may lead to fire or damage. Take care so as to protect from exposure to water, the entry of metallic pieces or dew condensation. In particular, a strong magnet adjacent to the pickup will not only get inoperative but can damage the pickup if a small metallic piece, such as a screw or swarm, enters. The loader edge can cause injury if inadvertently handled. Do not touch a rotating disk, or injury may result.

This product is a precision device. Handle carefully. A shock or dropping will cause misalignment or destruction. If it should occur, refer to clause 2. This product is so designed as to endure an initial shock equivalent to a drop from a height of approx. 90 cm under the packed condition. After the initial shock, the resistivity will still remain at a level of 50 to 60 G, but the mechanical robustness will weaken. Do not place in a dusty location. The entry and deposition of dirt into or on the pickup lens or moving section will cause malfunction or degradation.

DVD MECHANISM REPLACEMENT

(Connectors) Do not connect or disconnect while power is on. Connecting or disconnecting signal wires or the main power cord when the power is on may destruct the unit or fixture. When connecting, push all the way in securely. An insufficient insertion may cause a bad contact, leading to an erroneous operation. Do not connect or disconnect roughly by an excessively strong force, or a broken wire or bad contact may result. Semiconductors are connected. Do not touch connector terminals directly. If the worker is grounded, there is nothing to worry about static electricity, but the rust on the connector terminal surface caused by the touch may result in bad contact.

(Caution) Before disconnecting FFC cable, make it "SHORT" as shown left. After connecting FFC cable,make it "OPEN" as shownleft.

(Power source) The power source need be good in quality (free from instantaneous interruptions or noises). A low quality power source may well cause malfunction.

(Storage) Do not place or store in a dusty place or a place where dew condensation is possible. The entry and deposition of dirt or dust into or on the pickup lens or moving section will cause malfunction or degradation. Also, dew condensation causes rust; the rust penetrate into the precision part of a pickup, causing malfunction, or degrading the optical quality of the internal lens and reflector, which also leads to malfunction.

(OPEN)(SHORT)

- 4 -

Do not remove the pick-up from base mechanism because of adjustment difficulty.

GREASE CDF-409

GREASE EM-30LG

: Clean the groove by alcohol well.

GREASE EM-30LG

Apply screw lock

GREASE EM-30LG

4. Base mechanism mounting parts.

5. Base mechanism parts.

6. Tray parts.

MECHANISM REPLACEMENT

- 5 -

TROUBLE SHOOTING

Is thevOltageat

pin4and 5 of CN

about 5. 5V

POW ER DO ES NOT

DOESNOT LI

GHT

DISPLA

Check IC483 and peri

pheralcirc ui

th e volt age at pi n

of IC852 about 5. 0V

Is the volt

at pin

of IC851

out 3. 3V?

eck

IC852 and peri

eralcirc

uit.

CheckIC851 and peri

eral

circ ui t.

eck FL1 lineof PO

RBLOC

the volt

pi n1 and 2 of FL601

about-2 8V

plac e FL601 or IC60

LOAD ER DOES NOT ACCEPT OPEN/CLO SE

th e voltag e at pi

d22

of IC160about

Isthe

lose connection

0,CN15

0,CN160, CN

161

andCN

LOADER.

Ch eck 9V li

POWERBLOC

eck

each othe r connectionto

LOAD

eck IC 800 and

pheral

circ

uit.

AC IN,

LOAD

ERMOTOR turn

CheckOPENorSHORTat pi n 64,68, 73

and74 of IC80

Is th e volt ageat pi n

of IC850 about 1. 9V?

Check IC850 and peri

eral circ ui

Is th ere wavefo rm at X8000about 3. 0Vp-p?

eckX8000,IC800 and peri

pheral

circ uit.

Rewrit e ROM DA

Is th e volt

pi n31and 32 of FL601

about-2 5V

Is the voltageat

pi n13and 43 of IC601

about5V

Is thevoltag

at pi

of IC601

about-3 0V

Check FL2 li ne of

POWE

BLOC

Check IC852 and

peri

pheral ci

uit.

Check -3 0V line of

POWER

BLOCK.

PICTURE mode

BLACKand

Change PI CTUR

de to

STANDA

RD .

LOR

PLAYBACK PI

CTUR

COMPOSITEVIDEOOUT

X8230 osc is

.000

Check X8

230

and peripher

circ ui

Check IC820 or

change IC820.

- 6 -

TROUBLE SHOOTING

Is ther

DEO signal

at pi n 103 of IC820.

NO PLAYBACKPICTURE OF COMPOSITEVIDEOOU

NO PLAYBACKPICTUREOFS-VIDEO OUT

CheckCN870and peripheralcirc

ere

from

147 to pin159 ofIC820?

CheckIC130 and peripheralcircui t.

SelectS-VIDEOside.S8400 is S-VIDEOside?

Check IC820 or

change IC820.

ere

VIDE Osignal at

pin105 and 106 of IC82

S8400 is

MPONEN

VIDE Oside

CheckCN872 and peripher

circuit.

Sele

COMPONENT

NO PL

AYBACKPICUREOF COMPONENT

VIDEO(UK,XE:RGB)

OUT

there

VIDE

Osignal at

pin 102,105 and106 of

IC82

eck CN870 and peripher

rcui

DI GI TALAUDI O OUT ON PLAYBACK

Is th ere wa

veform

of IC 859?

the volt

age

at pi n

of IC 859 about 3. 3V?

CheckIC871 and peri phe ralcircui t.

Check IC851 and peripheral ci

rc ui

eck IC130 and peripheral

circui

there waveform at

13,14, 15 and 16 of IC 87

IC800 and peripheral circ

ther

veform atpin

13,14, 15 and16 of

IC87

Pi n 6 of IC859

is LO

Pi n 6 of IC859

is HIGH

OG AU

OOUT

ON PLAY

BACK

there AUDIO signal

pin7and8of IC871?

Is there waveform at pi

1, 2 and3of IC871?

eck IC872,Q8720, Q8820and

peripheral ci

rc ui

Check IC820 and peripheral ci rcuit.

Check IC871 or

change IC871.

Is th ere wavefo rm at pi n

13,14, 15 and 16 of IC87

Check IC800, IC820 and periph

eral

rcui

ange IC859.

(UK,XE:RGB)

- 7 -

SERVICE MODE

B. How to enter Service Mode.

You can enter Service Mode in any one of the following ways (1 to 3).

1. Using the buttons on the main unit Immediately (within one second) after pushing both STOP and POWER buttons simultaneously, push PREV button.

A. Market / Region SETUP

In the initial condition for this model, Market and Region information are undefined. In the following cases, be sure to set up Market/Region.

1. When updating the system using CD-R (Part code : 0PRADC7114--AJ).

2. When replacing a DVD substrate. While Market/Region information are undefined, the message "Region Undefined" is displayed on the screen.

NOTE: Even if the condition is not under 1 or 2 above, if the message "Region Undefined" is displayed, be sure to set up Market/Region.

2. Pushing the covered key located beneath Book Mark key on RB 1500 or REM-S1500.

3. Simultaneously pushing both Shift key and ON SCREEN key on PB-SL20.

- 10 -

SERVICE MODE

D. IMPORTANT NOTE

1. Once the "Market/Region" settings are written into EEPROM (IC801) on the DVD substrate, they cannot be reset. (However, updating the system using CD-R enables you to make new settings.)

2. While the Internal Setup screen is displayed, pushing the Power button enables you to terminate the operations without making any settings.

HOW TO LOAD SOFTWARE FOR MPEG P.W.BOARD

1. Power on, then open tray.

2. It take on CD-ROM for UPDATE software to the tray, and tray close.

3. Display " UP DATE" in the TV screen.

4. For the time being, tray open and FL display remain "UP DATE".

5. When software loading finished, FL display "STANDBY".

6. Next, set up market code and region code by "SERVICE MODE" CD-ROM part code is "0PRADC7114--AJ".

- 11 -

EXPLODED VIEW (CABINET & CHASSIS)

Y10

Y02

Y01

Y03

Y04

Y06

Y07

Y09

Y08

Y05

Y03

Y01

- 12 -

ELECTRICAL-PARTS

REF.NO. PART NO. DESCRIPTION

51 423 028 8207 FUSE 250V 1A,T1A L 250V 52 614 323 3237 ASSY,WIRE,LOADING-DVD 53 645 047 8055 CORD,POWER-1.8MK,FOR KR or 645 039 2528 CORD,POWER-1.75MK,FOR KR 54 614 323 3206 ASSY,WIRE,DVD-DG 55 645 053 8384 FLEXIBLE FLAT CABLE,

PICK-FFC(UL2896-24-P0.5-250MM) 56 645 051 0649 CORE,FERRITE,AC_CORD or 645 031 7637 CORE,FERRITE,AC_CORD 57 645 053 8506 FLEXIBLE FLAT CABLE,

IF-FFC(UL2896-8-P1.0-140MM )

PARTS LIST

PRODUCT SAFETY NOTICE

EACH PRECAUTION IN THIS MANUAL SHOULD BE FOLLOWED DURING SERVICING. COMPONENTS IDENTIFIED WITH THE IEC SYMBOL

IN THE PARTS LIST AND THE SCHEMATIC DIAGRAM DESIGNATED COMPONENTS IN WHICH SAFETY CAN

BE OF SPECIAL SIGNIFICANCE. WHEN REPLACING A COMPONENT IDENTIFIED BY

, USE ONLY THE REPLACEMENT PARTS DESIGNATED, OR PARTS WITH THE SAME RATINGS OF RESISTANCE, WATTAGE OR VOLTAGE THAT ARE DESIGNATED IN THE PARTS LIST IN THIS MANUAL. LEAKAGE-CURRENT OR RESISTANCE MEASUREMENTS MUST BE MADE TO DETERMINE THAT EXPOSED PARTS ARE ACCEPTABLY INSULATED FROM THE SUPPLY CIRCUIT BEFORE RETURNING THE PRODUCT TO THE CUSTOMER.

CAUTION : Regular type resistors and capacitors are not listed. To know those values, refer to the schematic diagram.

Regular type resistors are less than 1/4 W carbon type and chip resistors. Regular type capacitors are less than 50 V and less than 1000 µF type of Ceramic type and Electrical type.

PACKING & ACCESSORIES

REF.NO. PART NO. DESCRIPTION

614 324 6688 CARTON CASE,INNER 614 320 4077 CUSHION,TOP,TOP 614 320 4084 CUSHION,BOTTOM,BOTTOM 614 323 8645 CUSHION,PAD,PAD 614 324 6695 INSTRUCTION MANUAL,INST 645 052 1621 POLY BAG-0100X0250*NC,CABLE 645 011 9736 POLY BAG-0250X0350*NC,

INST MANUAL 645 036 4358 POLY SHEET-0850X0500*NC,SET 645 052 2352 REMOCON,RB-SL20,RB-SL20 645 037 3893 CABLE,A/V(-3)

or 645 023 0806 CABLE,A/V(-3) or 645 017 6012 CABLE,A/V(-3) or 645 003 3414 CABLE,A/V(-3)

CABINET & CHASSIS

REF.NO. PART NO. DESCRIPTION

1 614 322 4525 ASSY,DEC,DVD TRAY 2 614 323 8010 ASSY,CABINET,FRONT 3 614 321 2126 BUTTON,OPEN/CLOSE 4 614 320 3766 BUTTON,PLAY,PLAY 5 614 320 3889 CAP,BUTTON,PLAY,CAP PLAY 6 614 302 0530 DEC,WINDOW LED,STANDBY 7 614 320 3773 BUTTON,POWER,POWER 8 614 321 2331 ASSY,CABINET,BENDING,

AFTER BENDING

9 614 320 3728 ASSY,CABINET,BOTTOM 10 614 313 6545 SPRING,PLATE,SHIELD 11 614 129 1901 FIXER,AC CORD or 614 284 1884 FIXER,AC CORD 12 614 324 6664 PANEL,REAR 13 614 322 5997 MOUNTING,FFC,MOUNTING

FIXING PARTS

REF.NO. PART NO. DESCRIPTION

Y01 411 165 3803 SCR S-TPG BIN 2.3X10,

FRONT PWB FIX

Y02 411 098 4205 SCR S-TPG BIN 3X8,CABINET Y03 411 020 9803 SCR S-TPG BRZ+FLG 3X6,

DVD MECHA

Y04 411 021 6405 SCR S-TPG BIN 3X8,DG PWB Y05 614 130 0382 LUG,AC_CORD_FIX Y06 411 021 6405 SCR S-TPG BIN 3X8,MPEG PWB Y07 411 021 6405 SCR S-TPG BIN 3X8,

SPRING PLATE

Y08 411 021 3701 SCR S-TPG BIN 3X10,

BOTTOM-REAR

Y09 411 021 3701 SCR S-TPG BIN 3X10,

REAR-ELECT PART

Y10 411 021 2704 SCR S-TPG BIN 2.6X6,MOUNTING

FRONT P.W.BOARD ASSY

REF.NO. PART NO. DESCRIPTION

71 614 320 6149 ASSY,PWB FRONT(Only initial) BR601 614 315 5843 HOLDER,FL CN601 614 323 3213 ASSY,WIRE,FRONT-DVD D6001 407 012 4406 DIODE 1SS133 D6002 407 012 4406 DIODE 1SS133 D6040 407 012 4406 DIODE 1SS133 D6041 407 012 4406 DIODE 1SS133 D6042 407 012 4406 DIODE 1SS133 D6044 407 012 4406 DIODE 1SS133 D6045 407 012 4406 DIODE 1SS133 D6046 407 012 4406 DIODE 1SS133 D6401 408 032 5404 LED SLP-9118C-51H-S-T1,

STANDBY DS601 407 220 6803 PHOTO DIODE SPS-444-1-G1 FL601 645 044 8232 FLUORESCENT TUBE IC601 409 519 6907 IC PT6315 S6040 645 006 5958 SWITCH,PUSH 1P-1T or 614 220 5471 SWITCH,TACT or 614 240 1002 SWITCH,TACT or 645 048 3820 SWITCH,PUSH S6041 645 006 5958 SWITCH,PUSH 1P-1T or 614 220 5471 SWITCH,TACT or 614 240 1002 SWITCH,TACT or 645 048 3820 SWITCH,PUSH S6042 645 006 5958 SWITCH,PUSH 1P-1T or 614 220 5471 SWITCH,TACT or 614 240 1002 SWITCH,TACT or 645 048 3820 SWITCH,PUSH S6044 645 006 5958 SWITCH,PUSH 1P-1T or 614 220 5471 SWITCH,TACT or 614 240 1002 SWITCH,TACT or 645 048 3820 SWITCH,PUSH S6045 645 006 5958 SWITCH,PUSH 1P-1T or 614 220 5471 SWITCH,TACT or 614 240 1002 SWITCH,TACT or 645 048 3820 SWITCH,PUSH S6046 645 006 5958 SWITCH,PUSH 1P-1T or 614 220 5471 SWITCH,TACT or 614 240 1002 SWITCH,TACT or 645 048 3820 SWITCH,PUSH

- 13 -

DENGEN P.W.BOARD ASSY

REF.NO. PART NO. DESCRIPTION

72 614 324 8767 ASSY,PWB DENGEN(Only initial) C4809 403 357 8406 ELECT 1000U M 6.3V C4811 403 337 2103 ELECT 100U M 10V or 403 373 8305 ELECT 100U M 10V C4812 403 337 5500 ELECT 22U M 50V or 403 374 0704 ELECT 22U M 50V C4814 403 373 8800 ELECT 330U M 16V C4815 403 337 7207 ELECT 33U M 35V or 403 374 0001 ELECT 33U M 35V C4902 403 082 0201 POLYPRO 470P J 100V C4903 403 332 7202 ELECT 47U M 25V or 403 373 9203 ELECT 47U M 25V C4904 403 145 9103 CERAMIC 220P K 1K C4906 404 088 7409 MT-POLYEST 0.1U K 250V or 404 080 8206 MT-POLYEST 0.1U K 250V or 403 376 2409 MT-POLYEST 0.1U M 250V C4907 404 088 7409 MT-POLYEST 0.1U K 250V or 404 080 8206 MT-POLYEST 0.1U K 250V or 403 376 2409 MT-POLYEST 0.1U M 250V C4908 404 080 8107 CERAMIC 2200P M 400V CN481 614 310 2557 PLUG,14P or 645 006 0892 PLUG,14P D4802 408 043 6704 DIODE RGP10GL-22C-012 D4803 408 044 7304 DIODE SB160L-19C2-004 D4805 408 043 6704 DIODE RGP10GL-22C-012 D4806 408 043 6704 DIODE RGP10GL-22C-012 D4807 407 099 4603 ZENER DIODE MTZJ3.9B D4809 408 044 6307 DIODE SB140L 19C2-004 D4820 407 099 6607 ZENER DIODE MTZJ12B D4902 407 012 4406 DIODE 1SS133 D4904 407 004 9808 DIODE DSK10E or 407 012 0408 DIODE 1N4004 or 407 004 9808 DIODE DSK10E D4905 407 004 9808 DIODE DSK10E or 407 012 0408 DIODE 1N4004 or 407 004 9808 DIODE DSK10E D4906 407 004 9808 DIODE DSK10E or 407 012 0408 DIODE 1N4004 or 407 004 9808 DIODE DSK10E D4907 407 004 9808 DIODE DSK10E or 407 012 0408 DIODE 1N4004 or 407 004 9808 DIODE DSK10E D4910 407 012 4406 DIODE 1SS133 FPC01 645 006 4760 HOLDER,FUSE or 645 031 7903 HOLDER,FUSE FPC02 645 006 4760 HOLDER,FUSE or 645 031 7903 HOLDER,FUSE IC483 409 517 5704 IC KA431AZTF or 409 508 2804 IC KIA431A or 409 508 2705 IC KIA431 or 409 067 7203 IC L5431 IC490 410 431 1208 IC STR-G6351 LF1129 L4801 645 048 4469 INDUCTOR,22U or 645 045 8613 INDUCTOR,10U L4900 645 045 8941 LINE FILTER or 645 038 2024 LINE FILTER PC490 408 047 0005 PHOTO COUPLE H11A817B300 or 407 220 4601 PHOTO COUPLE PC123Y22 or 407 203 8602 PC PS2561-1-V PR481 645 042 2553 PROTECTOR,0.63A 125V PR482 645 042 2560 PROTECTOR,0.75A 125V PR484 645 042 2553 PROTECTOR,0.63A 125V PT490 645 045 6473 TRANS,POWER,PULSE Q4820 405 141 3109 TR KTC3203-Y or 405 024 9907 TR 2SD734-F or 405 025 0200 TR 2SD734-G R4908 402 087 3408 RESISTOR 3.3M J- 1/2W or 402 078 9501 CARBON 3.3M J- 1/2W or 402 078 8108 CARBON 3.3M J- 1/2W WR490 614 017 8203 TERMINAL BOARD WR491 614 017 8203 TERMINAL BOARD

PARTS LIST

DVD/MPEG P.W.BOARD AASY

REF.NO. PART NO. DESCRIPTION

73 614 323 2971 ASSY,PWB DVD/MPEG(Only initial) C1050 403 373 9203 ELECT 47U M 25V C1901 403 373 7902 ELECT 150U M 6.3V C8535 403 373 7902 ELECT 150U M 6.3V CN100 645 037 6207 SOCKET,FFC 24P CN160 614 310 2465 PLUG,5P or 645 005 9292 PLUG,5P CN162 645 043 8882 SOCKET,FPC 8P CN811 614 310 2557 PLUG,14P or 645 006 0892 PLUG,14P CN814 614 310 2557 PLUG,14P or 645 006 0892 PLUG,14P CN870 645 041 1298 JACK,RCA-6 CN871 407 223 4004 PHOTO COUPLE GP1FA551TZ or 407 221 6406 PHOTO COUPLE TOTX179 CN872 645 044 9086 SOCKET,DIN 4P D1101 407 221 1807 DIODE KDS120E or 407 179 1805 DIODE DAP222 D1102 407 221 1906 DIODE KDS121E or 407 162 8507 DIODE DAN222 D8531 407 206 5608 ZENER DIODE UDZS10B D8801 407 221 6505 ZENER DIODE KDZ5.6V or 407 208 9703 ZENER DIODE UDZS5.6B or 407 179 4608 ZENER DIODE UDZ5.6B D8880 407 149 0807 DIODE 1SS355 D8881 407 224 8605 DIODE KDS226 IC100 409 482 3903 IC LA9702WL-MPB IC101 409 521 9606 IC CD4066BCM IC130 409 500 6404 IC LC78661W-D IC141 409 447 3702 IC T224162B-35S or 410 367 3604 IC LC324265AT-25DV-TLM or 409 447 3702 IC T224162B-35S or 410 375 9407 IC LC324265AT-25DV-MPB or 410 388 4505 IC M11B416256A-35T IC160 409 532 0005 IC LA6560-A IC800 409 522 0701 IC ZR36705TQC IC801 410 430 9601 IC S524C20D21-SCT0 or 410 429 7809 IC S524C20D21-SCB0 or 410 429 7908 IC AT24C02N-10SI-2.7 IC802 409 505 0803 IC PST3627U IC806 410 430 9403 IC 74VHCT08AMTCX IC818 410 440 2401 IC ASSY

(IC LE28DW8163T-70T-MPB,

FLASH 8M) IC820 410 422 1408 IC ZR36732 IC821 409 482 0209 IC K4S161622D-TC80 IC850 409 509 9208 IC PQ070XZ01Z IC851 409 509 9208 IC PQ070XZ01Z IC852 409 509 9208 IC PQ070XZ01Z IC859 409 489 9700 IC NC7SZ157P6 IC871 409 500 3304 IC PCM1748E,DAC_2CH IC872 409 426 1903 IC KIA4558F or 409 039 7804 IC NJM4558M L1001 645 034 7887 INDUCTOR,1000 OHM or 645 020 1813 INDUCTOR,1000 OHM L1090 645 034 7887 INDUCTOR,1000 OHM or 645 020 1813 INDUCTOR,1000 OHM L1100 645 034 7887 INDUCTOR,1000 OHM or 645 020 1813 INDUCTOR,1000 OHM L1190 645 034 7887 INDUCTOR,1000 OHM or 645 020 1813 INDUCTOR,1000 OHM L1191 645 034 7887 INDUCTOR,1000 OHM or 645 020 1813 INDUCTOR,1000 OHM L1300 645 034 7887 INDUCTOR,1000 OHM or 645 020 1813 INDUCTOR,1000 OHM L1301 645 034 7887 INDUCTOR,1000 OHM or 645 020 1813 INDUCTOR,1000 OHM L8201 645 034 7887 INDUCTOR,1000 OHM or 645 020 1813 INDUCTOR,1000 OHM L8400 645 040 6430 INDUCTOR,2.2U M L8410 645 040 6430 INDUCTOR,2.2U M L8420 645 040 6430 INDUCTOR,2.2U M L8451 645 040 6430 INDUCTOR,2.2U M

+ 32 hidden pages

Sanyo DVD-SL20V Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual