Sanyo DP58D33 Owner's Manual
HDMI
VIDEO INPUT
2
HDMI
1
(DVI)
(DVI AUDIO)
(VIDEO)
The American Academy of Pediatrics discourages media use by children younger
than two years. For more information,
visit www.aap.org.
Please read before operating your HDTV!
PROTECTING THE LCD
SCREEN
CAUTION: The screen can be damaged if
it is not maintained properly.
•
Do not use hard objects such as hard
cloth or paper to clean the screen.
•
Do not use excessive pressure when
cleaning the screen; excessive pressure
can cause permanent discoloration or
dark spots.
•
NEVER spray liquids on the screen.
HANDLING PRECAUTIONS
•
Handle by the cabinet only.
•
Handling by two or more people is recommended.
•
Never touch the screen when handling.
•
Handling damage is not covered under
warranty.
•
Do not remove the protective film
covering the front cabinet while
handling the HDTV.
POSITIONING THE HDTV
•
Always use a firm and flat surface when
positioning your HDTV.
•
Do not position the unit in a confined
area.
•
Allow adequate space for proper ventilation.
•
Do not position the HDTV where it is
easily reachable by small children and
may present risk of injury.
•
Once HDTV is positioned, remove the
protective film covering front cabinet.
SPECIFICATIONS
NOTE: Design and specifications are
subject to change without notice.
Power Requirement:
Source: AC 120V, 60Hz
AC Power Consumption: 155 watts
Weight: 48.1 lbs (w/stand)
Dimensions _________________________
WIDTH HEIGHT DEPTH
w/stands 51.3 31.5 10.5
w/out stands 51.3 30.4 3.9
NOTE: Dimensions are in inches
SANYO television customers should contact MRM
Recycling at 888-769-0149 or
visit their website at
www.mrmrecycling.com
regarding SANYO’s waste
management plan.
NOTE: Skip these steps if using a wall
mounting kit (not included).
1
Place HDTV face down on a
padded or cushioned flat surface
to protect the screen and finish.
2
Carefully insert both foot stands to
the bottom of the HDTV and secure
them by inserting two (2) long
screws (M4 4x30) in each one as
indicated in the diagram below.
NOTE: Foot stand screws are located in
the literature package.
3
Position the HDTV on a firm and
flat surface with adequate space
for proper ventilation.
STAND ASSEMBLY ______
GETTING STARTED
Hook up your antenna or your cable
service to the HDTV’s ANT terminal
with the use of a 75 OHM coaxial cable.
NOTE: Keep your indoor antenna at
least 3 ft. away from the television set and any other electronic equipment.
The tuner in this HDTV can receive:
•
Digital and Analog off air signals
from an antenna
• Analog or ClearQAM cable channels
from a direct Cable TV connection.
ANTENNA CONNECTION FOR
OFF-AIR SIGNALS OR CABLE
ANTENNA
CABLE
ANALOG / DIGITAL
ANTENNA IN
AV INPUT SELECTION
Press the INPUT key to select the
correct AV input for the video source
you wish to watch.
NOTE: Unused AV inputs may be disabled with the Input Setting feature.
Finish Setup
Repeat
Channel Search Result: Succesfully Completed
If you are having problems, call us toll-free at 1-800-877-5032
Analog Channels
Video HDMI 1 HDMI 2
Digital Channels16 26
HDMI 3
Before proceeding, please make
sure to correctly hook up your
antenna or cable connection and
all AV equipment to your HDTV.
1. PLUG IN AC POWER CORD
120V AC, 60Hz
2. TURN ON TV
3. TV SET LOCATION SELECTION:
Select “
Home Mode
” to set the
HDTV’s backlight to an Energy Star
qualified level, or select “
Store
Mode
” to set the backlight to a retail
display level.
4. CHANNEL AND SIGNAL SEARCH:
Select “
Signal Search
” and press
ENTER to perform a channel search
from an Antenna or a direct Cable
connection, and a signal search
from devices hooked up to the
HDTV’s AV input jacks.
5. SIGNAL SEARCH RESULT SCREEN
The final setup screen displays analog and digital channels found, as
well as AV inputs detected.
Select
Finish Setup
and press
ENTER.
NOTE: If you wish to repeat the
process, select Repeat.
INITIAL CHANNEL SEARCH
Need help? www.sanyoctv.com 1-800-877-5032 Need help? www.sanyoctv.com 1-800-877-5032
class
D
As an Energy Star®Partner, Sanyo
Manufacturing Corporation has
determined that this product
meets the Energy Star
®
guidelines
for energy efficiency.
TRADEMARKS ________
Manufactured under license from Dolby
Laboratories. “Dolby” is a trademark of
Dolby Laboratories.
HDMI, the HDMI Logo and High-Definition
Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in
the United States and other countries.
HDTV INPUT/OUTPUT REFERENCE ________________________________________
HDTV SIDE PANEL
1
ANT Analog / Digital Antenna Input
Hook up your indoor or outdoor digital antenna, or a direct
Cable service (Analog or ClearQAM).
VIDEO INPUT (COMPONENT/COMPOSITE combo)
COMPOSITE Connection
A Composite connection is used to hookup your analog
equipment such as a VCR or an older DVD player.
Match the YELLOW connector from your external device to
the GREEN Y-VIDEO jack on the HDTV.
NOTE: Use the WHITE and RED (L and R) jacks for AUDIO
signal.
COMPONENT Connection
A Component connection will accept SDTV, EDTV and
HDTV video signals. Use it for great image quality from digital devices such as a DVD player or Video Game system.
Match your digital device’s Component output jacks to the
Component input jack set on your HDTV.
NOTE: Use the GREEN (Y), BLUE (Pb) and RED (Pr) jacks for the
VIDEO signal and the WHITE and RED (L and R) jacks for
the AUDIO signal.
HDMI (INPUT1 or INPUT2)
Use HDMI INPUT1 & 2 to hookup HD digital devices such as
a Blu-ray player, HD Cable Box, HD Satellite Receiver or
Video-game System.
Connect your digital device’s HDMI output to any of the two
(2) HDMI inputs on your HDTV’s side panel with the use of
an HDMI cable.
NOTE: A DVI connection is possible via the HDMI (DVI) INPUT1
using an appropriate cable or adapter and connecting the
audio to the L and R (VIDEO INPUT) jacks.
USB
USB input jack is used to connect a USB mass storage
device to watch digital images stored in JPEG format.
DIGITAL AUDIO OUT (Coaxial)
Hookup a multichannel receiver with the use of a phonotype digital audio cable.
HDMI (INPUT3)
Use HDMI INPUT3 to hookup HD digital devices such as a
Blu-ray player, HD Cable Box, HD Satellite Receiver or
Video-game System.
Connect your digital device’s HDMI output to the HDMI3
input on your HDTV with the use of an HDMI cable.
1
2
3
4
5
6
Printed in Mexico, January 2013
US3B / 58-Z7GB / GXHA
Sanyo Manufacturing Corp. 3333
Sanyo Road, Forrest City, AR 72335
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than
the other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit fully into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. If an outside antenna is connected to the television equipment,
be sure the antenna system is grounded so as to provide some
protection against voltage surges and built up static charges.
In the U.S. Selection 810-21 of the National Electrical Code provides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location
of antenna discharge unit, connection to grounding electrodes,
and requirements for the grounding electrodes.
16. An outside antenna system should not be located in the vicinity of overhead power lines or other electrical light or power
circuits, or where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme care
should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
EXAMPLE OF ANTENNA GROUNDING ACCORDING
TO NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
“Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.”
17. Wall or Ceiling Mounting—The product should be mounted to
a wall or ceiling only as recommended by the manufacturer.
18. Apparatus shall not be exposed to dripping or splashing, and no
objects filled with liquids, such as vases, shall be placed on it.
19. When the MAINS plug is used as the disconnect device, the
disconnect device shall remain readily operable.
RISK OF ELECTRIC SHOCK DO NOT OPEN!
CAUTION: TO REDUCE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK
OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
FCC INFORMATION ________________________________________________
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION: FCC Regulations state that improper modifications or unauthorized changes to this unit may void the user’s authority to
operate the unit.
This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require
a safety connection to electrical earth.
Install two (2) “AAA” batteries in the
remote control. (Not included)
PRECAUTIONS:
• Replace both batteries at the same
time. Do not use a new battery with a
used battery.
• There’s a risk of explosion if a battery
is replaced by an incorrect type.
• Keep away from moisture.
• Be sure to match the “+” and “–”
signs on the batteries with marks
inside the remote control.
• Please properly dispose of used up
batteries.
WARNING: The batteries (or battery
pack) shall not be exposed to excessive
heat such as sunshine, fire or the like.
BATTERY INSTALLATION
ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection
Agency (EPA). ENERGY STAR is a joint program of the U.S. Environmental Protection Agency and
the U.S. Department of Energy helping us all save money and protect the environment through
energy efficient products and practices.
Changes to default as-shipped television configuration and settings or enabling certain optional
features and functionalities will change the energy consumption of the television, this may
increase energy consumption beyond the limits required for ENERGY STAR qualification.
2
3
HDMI
3
DIGITAL
AUDIO OUT
HDTV BACK PANEL
5
6
4
WALL MOUNTING (OPTIONAL)
Wall mounting of the HDTV must be
performed by a skilled person.
If foot stand disassembly is required:
•
Place HDTV face down
on a padded or
cushioned flat surface to protect the
screen and finish.
•
Remove the two (2) screws securing
each foot stand. CAUTION: Hold the
stands firmly as you remove the last
screw.
Use the four (4) short screws
included in the literature package
to secure the HDTV to a wall
mounting kit (not included.)
IMPORTANT: Wall mount kit must
comply with VESA standard 400 x
400. All four (4) screws must be
threaded to the wall mount and
HDTV’s back cabinet
Mounting screws measurements:
M6 (6mm) Diameter, Length 12mm
(min.) – 16mm (max.)
58”LED
1080p HDTV LCD
080p HDTV LC
Part No.:
© 2013 Sanyo Manufacturing Corporation
(57.5” diagonal)
1JC0P1P0041- -
Model:
DP58D33
Owner’s
Manual
ENERGY STAR
(English)
REMOTE CONTROL OPERATION _______________________________
Auto – Searches the detected mode,
Cable or Air.
Cable – Searches for analog and
unscrambled (ClearQAM) digital cable
channels.
Air (Antenna) – Searches for analog
and digital off-air channels.
Channel Search
Display the On Screen menu and use
the CURSOR keys to select
Channel.
Press ENTER.
ON-SCREEN MENU
OPERATION
Channel Scan Memory lists all Analog
and Digital channels found. It also lists
Analog channels that were not found,
which can be added.
Use the CURSOR keys to move the
channel select bar through all enabled
and disabled channels.
NOTE: You can use the CHkeys to
change page.
Press ENTER to enable or disable the
selected channel.
NOTE: For information on local digital
channels, visit www.antennaweb.org
Channel Scan Memory
Channel
Auto
Cable
Air (Antenna)
Move
Select
ENTER ExitEXIT
ReturnMENU
TV
Channel Search
Channel Scan Memory
Input Setting
Video Setting
Channel Scan Memory
Move SelectENTERPageCH ExitEXITReturnMENU
TV
Analog
Digital
Digital
Analog
Analog
Analog
Digital
03
03-1
03-2
04
05
06
06-1
WREG-DT
WCVB
WEXT
NICK
NICK
VBCT
IMPORTANT FACT: This HDTV maintains only
one database of digital channels. Therefore,
when you search for cable channels, the
database of antenna digital channels will be
deleted. You will only be able to receive those
ClearQAM channels your cable company
provides.
Input Setting feature allows the
removal of unused inputs from the AV
input loop.
Use the CURSOR keys to select an
AV input. Press ENTER to disable
(uncheck) or enable (check) the highlighted input.
NOTE: At least one input must and
will remain checked.
Unchecked box means the input will
be skipped
Input Setting
Channel
Move
Select
ENTER ExitEXIT
ReturnMENU
TV
Channel Search
Channel Scan Memory
Input Setting
Video Setting
Video
HDMI1
HDMI2
HDMI3
USB
:Skip
Use this feature to establish either a
Component or Composite connection
to the VIDEO INPUT jacks on your TV.
Video Setting
SETUP
Display the On Screen menu and use
the CURSOR keys to select
Setup.
Press ENTER.
Menu Language
Choose between English, Spanish and
French for your On Screen menu’s display language.
Press ENTER on the desired language.
Captioning is textual information transmitted along with the picture and
sound. Turning Captioning ON (by
pressing the CAPTION key during normal TV viewing) causes the HDTV to
open these captions (digital or
analog) and superimpose them on the
screen.
NOTE: Local broadcasters decide
which caption signals to transmit.
Use the CURSOR and keys to
modify
Font, Background,
and
Foreground
of digital caption text.
Digital Caption
This feature allows you to set a
Current Time
for your HDTV and
enable a
Switch On Time
for the HDTV
to turn on at a specific time of day.
When
On Timer Function
is set to ON,
the TV will automatically turn on at the
previously set
Switch on Time
.
Use the CURSOR and keys to
modify the
Current Time
and/or
Switch
On Tim
e.
Clock Timer
Use this feature to automatically block
programs with content you deem as
inappropriate for viewing by your
children.
NOTE: This feature is designed to com-
ply with the United States of
America’s FCC V-Chip regulations. Therefore, it may not function with broadcasts that originate in other countries.
ADJUSTING THE V-CHIP RATINGS
Select
ON
and press ENTER. Select
Adjust (Standard)
and press ENTER.
V-Chip (parental control)
For V-Chip (TV) ratings select TVand
press ENTER. Use the CURSOR
keys to select a rating and press ENTER.
Use the CURSOR keys to set the
rating’s status as
Blocked
or
Viewable.
Once ratings are set, press the EXIT key
to close the V-Chip menu.
Display the On Screen menu and use
the CURSOR keys to select
Picture.
Press ENTER.
You may choose between
Vivid, Mild,
and
Standard
, which have predetermined fixed picture parameter
values, or choose the
Manual
option
for customized personal settings.
NOTE: Each AV input can have its
own picture mode (pre-determined or manual.) Current
input’s selected option is indicated by a blue marker.
MANUAL PICTURE SETTINGS
Manual
parameters to adjust include:
•
Color
•
Tint
•
Contrast • Brightness
•
Sharpness • Color Temperature
The
Detailed Setting
option allows for
the adjustment of several additional
parameters such as:
•
Signal Balancer• Noise Reduction
•
White Balance• Edge Enhancer
•
H-Size / V-Size • Dynamic Contrast
Picture
Vivid
Mild
Standard
Manual
Color
Tint
Contrast
Brightness
Sharpness
Color Temperature
Detailed Setting
Default
Move
Select
ENTER ExitEXIT
ReturnMENU
TV
ADJUSTING A PICTURE SETTING
Use the CURSOR keys to highlight
the picture parameter you wish to
adjust. Press the ENTER key to enter the
value adjustment screen. Modify the
selected parameter’s value by pressing
the CURSOR keys.
NOTE:
CURSOR
keys select the
next/previous parameter without returning to the previous
menu screen.
Once adjustments are complete, press
the EXIT key to return to normal TV
viewing.
Display the On Screen menu and use
the CURSOR keys to select
Sound.
Press ENTER.
Choose sound setting option:
Auto – Sound settings are linked to
the current Picture option and parameters are adjusted accordingly.
Dynamic, Mild, Standard –
Predetermined sound parameters not
linked with any Picture option.
MANUAL SOUND SETTINGS
The
Manual
option provides different
parameters that can be personally
adjusted:
•
Bass & Treble
•
Bass Boost
•
Detailed Setting
– Equalizer:
Personalize audio highs
and lows.
Manual
Move
Select
ENTER ExitEXIT
ReturnMENU
TV
Bass
Treble
Bass Boost
Detailed Setting
Default Sound
ON
ADJUSTING A SOUND SETTING
Use the CURSOR keys to highlight
the sound parameter you wish to adjust.
Press the ENTER key to enter the value
adjustment screen. Modify the selected
parameter’s value by pressing the
CURSOR keys.
NOTE:
CURSOR
keys select the
next/previous parameter without returning to the previous
menu screen.
Once adjustments are complete, press
the EXIT key to return to normal TV
viewing.
View pictures on your HDTV with the
use of a USB mass storage device (not
included.)
USB FLASH
DRIVE
PHOTO VIEWER
USB INPUT
HDTV SIDE PANEL
Your Sanyo HDTV is registered at the time of purchase,
please keep sales receipt for future reference.
For your protection in the event of theft or loss of this product, please fill in the
information requested below and KEEP IN A SAFE PLACE FOR YOUR OWN
PERSONAL RECORDS.
Model No. ______________________ Serial No. _____________________________
Purchase date ___________________ Purchase Price _________________________
Where Purchased _________________________
(Located on back of unit)
ONE-YEAR LIMITED PARTS AND LABOR
WARRANTY
THIS LIMITED PARTS AND LABOR WARRANTY IS VALID ONLY ON SANYO TELEVISIONS
PURCHASED AND USED IN THE UNITED STATES OF AMERICA, CANADA, AND PUERTO
RICO, EXCLUDING ALL OTHER U.S. TERRITORIES AND PROTECTORATES. THIS LIMITED
WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL PURCHASER, AND DOES NOT
APPLY TO PRODUCTS USED FOR INDUSTRIAL OR COMMERCIAL PURPOSES.
WARRANTY APPLICATION
FOR ONE YEAR from the date of original retail purchase Sanyo Manufacturing
Corporation (SMC) warrants this TV to be free from manufacturing defects in materials and
workmanship under normal use and conditions for parts and labor.
For the FIRST 90 DAYS from the date of original retail purchase, Sanyo Manufacturing
Corporation will replace any defective TV via exchange at the retailer. To ensure proper
warranty application, keep the original-dated-sales receipt for evidence of purchase.
Return the defective TV to the retailer along with the receipt and the included
accessories, such as the remote control. The defective TV will be exchanged for the same
model, or a replacement model of equal value, if necessary. Replacement model will be
contingent on availability and at the sole discretion of Sanyo Manufacturing Corporation.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
OBLIGATIONS
For one year
from the date of purchase, Sanyo Manufacturing Corporation warrants
this product to be free from defects in material and workmanship under normal use and
conditions. During the first 90 days under this warranty for any manufacturing defect or
malfunction Sanyo Manufacturing Corporation will provide a new TV via exchange at
the retailer.
HOW TO MAKE A CLAIM UNDER THIS WARRANTY
Please call 1-800-877-5032. Please be prepared to give us the television’s model number
and serial number when you call. The model number and serial number are printed on a
label attached to the back of the unit.
For customer assistance, call toll free 1-800-877-5032.
This warranty expresses specific contractual rights; retail purchasers may have additional statutory rights which vary from state to state.
(EFFECTIVE: March 1, 2007)
(Located on back of unit)
CHANNEL
PICTURE
SOUND
POWER. Turns your HDTV On or Off.
INPUT
.
Selects the video source to
view. Holding down the key displays
the Input List.
NUMERIC KEYS
.
Choose a channel
directly.
SUB CH
.
Use for the direct selection of
digital subchannels. For example: for
channel 39-1 press the
3 and 9 keys,
followed by the dash
––
, and 1 keys.
RECALL
.
Switch between current chan-
nel and last selected channel or input.
MUTE
.
Mute or restore the sound.
VOL +
––
.
Increases or decreases the
audio level.
CH
.
Scan through the channels in
the memory database.
AUDIO
.
Selects the desired Audio
mode. Stereo, Mono, or SAP (when
available.)
PIX SHAPE
.
Cycles through the various aspect ratios. The different settings either stretch, zoom, or fill the
image on your screen. Bars may
appear on top and bottom of your
screen (or on left and right sides)
depending on the broadcasted signal
or program.
CAPTION
.
Cycles through the available
Caption modes (when available.)
MENU. Display or hide the on-screen
menu.
HELP. Displays the on-screen Help menu.
CURSOR
.
Move the on-screen
cursor in the desired direction.
ENTER. Set or select the highlighted
option on the screen.
INFO
.
Displays the Channel Information
banner.
EXIT
.
Exits the on-screen menu.
ON TIMER. Displays the current switch
on time (if activated.)
RESET
.
Pressing it twice restores your
HDTV to its factory settings. All user
customized settings will be cleared.
SLEEP. Displays the “Off” Timer. While
Off Timer is on-screen, press the “0”
key to Set the amount of time (in 30
minute increments) at which the HDTV
will turn off.
ECO
.
Modifies the
Energy Saver
level.
Energy Solution
ECO (ENERGY SAVER)
ECO controls the LCD backlight brightness to reduce power consumption.
– Level 1: Energy Saver feature is off.
– Level 2: Low power consumption.
– Level 3: Lowest power consumption.
Press ENTER on the desired level.
LIGHT SENSOR
This feature detects ambient room
light brightness and uses that reading
to control the panel brightness level
and picture parameters to reduce the
HDTV’s power consumption.
NOTE: When room lighting is dark,
the panel brightness and/or the
picture setting parameters
such as brightness and contrast are lowered. When room
lighting is bright, parameters
are affected opposite.
Use the CURSOR keys to select
On
or
OFF
and press ENTER.
AUTO SHUT-OFF
When Auto Shut-off feature is set to
ON
, it will allow the HDTV to automatically turn off when no video and/or
audio signals are being received.
NOTES: By factory default, this fea-
ture is set to ON. The HDTV
will automatically turn off if
no AV signals are received in
a time span of 15 minutes.
Use the CURSOR keys to select
On
or
OFF
and press ENTER.
Choose to modify the initial Energy
Saving Mode chosen at HDTV’s first
power on.
Home Mode - For saving energy and
power consumption reduction.
Store Mode - High brightness and
contrast for display at retailer store.
Demo Mode - High brightness and
contrast plus TV feature demonstration.
NOTE: Only Home Mode qualifies for
Energy Star.
Mode (Home/Store/Demo)
NOTE: A thumbnail hide icon will
appear if a picture cannot be decoded
or if no thumbnail data is available.
Thumbnail veiw
EXIT
USING THE PHOTO VIEWER
Press ENTER on a thumbnail photo to
enable the
Full View and Start
Slideshow
functions.
Once in
Full View
mode:
Use the CURSOR keys to change
picture.
Press ENTER to show the full view
options menu.
•
Rotate
•
Zoom In / Out
•
Pan
•
Slideshow setup
•
Start Slideshow• Browse Photo
SLIDE SHOW
In the
Slideshow Setup
menu you may
turn the
Shuffle
and
Quick Change
options ONor
OFF
.
Press ENTER on
Start Slideshow
either from the Thumbnail View
Screen or from the full view options
menu to start the slideshow from the
current picture.
Insert the flash drive into the USB port,
the TV will display the Photo Viewer
thumbnail screen.
NOTE: INPUT key can also be used to
select the USB input on your HDTV.
NOTE: Blocking a rating will automati-
cally block all higher ratings.
Unblocking a rating will automatically unblock all lower
ratings.
For V-Chip (Movie) ratings select
Movie
and press ENTER, and then select the
desired MPAA rating limit. Press the
EXIT key to close the V-Chip menu.
ADVANCED V-CHIP SYSTEM (RRT5)
RRT5 (V-Chip Regional Ratings 5) is an
advanced V-Chip ratings system for over
the air digital channels. When compatible RRT5 data is detected, it’s downloaded & stored in memory, and the
Setup V-Chip screen is then modified to
show the
Adjust (Advanced)
option.
Use the CURSOR and keys to
highlight the different options, and use
the ENTER key to block or unblock the
selected rating.
NOTE: When vertical scroll bars appear,
press CURSOR
to gain
access to the additional ratings.
MORE INFORMATION
Additional information about MPAA
(Motion Picture Association of
America) and V-Chip rating can be
found at: www.mpaa.org and
www.v-chip.org, respectively.
Your HDTV will display all signals at the
refresh rate of
120Hz. Motion Sync
is a special Frame
Rate Converter feature that helps
eliminate motion blur and film judder
in scenes with fast moving action.
• On – Full advantage of TV’s refresh
rate capabilities for the best
picture quality.
• Off – Disables the Motion Sync
Frame Rate Converter feature.
NOTE: Off setting is recommended for
some faster paced video games
due to reduced picture delay.
Motion Sync (120 Hz)
Once in the Video Setting menu, use
the CURSOR keys to select
Component (Y/Pb/Pr)
if your hookup
uses five (5) jacks like on the left; or
select
Composite (V)
if your hookup
uses three (3) jacks like on the right.
NOTE: Selecting Auto Detection will
establish the correct Video Setting
depending on the type of connection
used in VIDEO INPUT.
SUB CH
INFO
GXHA
Composite connection
(VIDEO)
VIDEO INPUT
(DVI AUDIO)
Component connection
Loading...