Sanyo DP55360 User Manual

2

Need help? www.sanyoctv.com 1-877-864-9604

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding-type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided
plug does not fit fully into your outlet, consult an electri­cian for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the
manufacturer.

12. Use only with the cart, stand, tripod,
bracket, or table specified by the manu­facturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when
unused for long periods of time.

14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.

15. If an outside antenna is connected to the television
equipment, be sure the antenna system is grounded so
as to provide some protection against voltage surges
and built up static charges. In the U.S. Selection 810-21
of the National Electrical Code provides information with
respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of
antenna discharge unit, connection to grounding elec­trodes, and requirements for the grounding electrodes.

16. An outside antenna system should not be located in the
vicinity of overhead power lines or other electrical light
or power circuits, or where it can fall into such power
lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from
touching such power lines or circuits as contact with
them might be fatal.

EXAMPLE OF ANTENNA GROUNDING ACCORDING
TO NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

“Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the build­ing, as close to the point of cable entry as practical.”

17. Wall or Ceiling Mounting—The product should be
mounted to a wall or ceiling only as recommended by
the manufacturer.

18. Apparatus shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases, shall be
placed on the apparatus.

19. When the MAINS plug is used as the disconnect device,
the disconnect device shall remain readily operable.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN!

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SER­VICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A
RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS
UNIT.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.

IMPORTANT SAFETY INSTRUCTIONS

3

Need help? www.sanyoctv.com 1-877-864-9604

This symbol on the nameplate means
the product is Listed by Underwriter’s
Laboratories Inc. It is designed and
manufactured to meet rigid U.L. safety
standards against risk of fire, casualty
and electrical hazards.

FCC INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

CAUTION: FCC Regulations state that improper modifications or unauthorized changes to this unit may void

the user’s authority to operate the unit.

TRADEMARKS

PC RESOLUTION CHART

This Class B digital apparatus complies with Canadian
ICES-003.

As an Energy Star

®

Partner, Sanyo
Manufacturing Corporation has deter­mined that this product meets the
Energy Star

®

guidelines for energy

efficiency.

Manufactured under license from
Dolby Laboratories. Dolby and the
double-D symbol are trademarks of
Dolby Laboratories.

HDMI, the HDMI Logo and High­Definition Multimedia Interface are
trademarks or registered trademarks
of HDMI Licensing LLC in the United
States and other countries.

Adobe®, Adobe Flash®, and Flash Lite

®

are either registered trademarks or
trademarks of Adobe Systems
Incorporated in the United States
and/or other countries.

4

Need help? www.sanyoctv.com 1-877-864-9604

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . 2

FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

TRADEMARKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

PC RESOLUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

PROTECTING THE SCREEN . . . . . . . . . . . . . . . . . . . . . . . . .4

POSITIONING THE HDTV . . . . . . . . . . . . . . . . . . . . . . . . . . .5

STAND REMOVAL / WALL MOUNTING . . . . . . . . . . . . . . .5

GETTING STARTED—

Remote Control Battery Installation . . . . . . . . . . . . . . . .5

Antenna Connections for off-air or cable . . . . . . . . . . .5

HDTV INPUT/OUTPUT REFERENCE . . . . . . . . . . . . . . . . . . .6

A/V CONNECTIONS (SIDE PANEL) . . . . . . . . . . . . . . . . . . .7

A/V CONNECTIONS (BACK PANEL) . . . . . . . . . . . . . . . . . .8

POWER CONNECTION / INITIAL CHANNEL SEARCH . . .9

REMOTE CONTROL OPERATION . . . . . . . . . . . . . . . . . . . .10

ON-SCREEN MENU OPERATION—

Channel / Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Channel Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Channel Scan Memory . . . . . . . . . . . . . . . . . . . . . . .11

Input Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Video3 Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

HDMI Linking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Digital Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Energy Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Clock Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Motion Sync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

V-Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

PC CONNECTIONS & MENU OPERATION . . . . . . . . . . . .18

PHOTO VIEWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

PROTECTING THE SCREEN

CAUTION: The screen can be damaged if it is not

maintained properly.

•

Do not use hard objects such as hard cloth or
paper to clean the screen.

•

Do not use excessive pressure when cleaning
the screen; excessive pressure can cause
permanent discoloration or dark spots.

•

NEVER spray liquids on the screen.

HANDLING PRECAUTIONS

•

Handle by the cabinet only.

•

Never touch the screen when handling.

•

Handling damage is not covered under warranty.

POSITIONING THE HDTV

•

Always use a firm and flat surface when
positioning your HDTV.

•

Do not position the unit in a confined area.

•

Allow adequate space for proper ventilation.

SPECIFICATIONS

Power Requirement: Source: AC 120V, 60Hz

AC Power Consumption: Weight:

195 watts 75 lbs.

Dimensions:

MODEL WIDTH HEIGHT DEPTH

DP55360 51.2 34.5 10.9

w/o stand 32.3 2.4

NOTE: Dimensions are in inches

Please read before
operating your HDTV!

“The Amercian Academy of Pediatrics discourages
television viewing for children younger than two
years of age”

5

Need help? www.sanyoctv.com 1-877-864-9604

1

Remove the two (2) screws holding the stand
base cover and carefully dislodge.

STAND REMOVAL AND WALL
MOUNTING

(OPTIONAL)

Tools Needed: Phillips screwdriver

IMPORTANT NOTE: Place HDTV face down

on a padded or cushioned flat surface to

protect the screen and finish.

Wall mounting of the HDTV must be performed
by a skilled person.

GETTING STARTED

Install two (2) “AAA” batteries in the remote
control. (Not included)

To ensure safe operation, please observe the
following precautions:

• Replace both batteries at the same time. Do not use a
new battery with a used battery.

• There’s a risk of explosion if a battery is replaced by
an incorrect type.

• Do not expose the Remote Control unit to moisture
or heat.

• Be sure to match the “+” and “

–” signs on the

batteries with marks inside the remote control.

ANTENNA CONNECTION FOR
OFF-AIR SIGNALS OR CABLE

ANTENNA

CABLE

ANALOG / DIGITAL

ANTENNA IN

BATTERY INSTALLATION

Hook up your antenna or your cable service to
the HDTV’s ANT terminal with the use of a 75
OHM coaxial cable.

NOTE: Keep your indoor antenna at least 3 ft. away

from the television set and any other electronic
equipment.

The tuner in this HDTV can receive:

• Digital and Analog off air signals from an antenna

• Analog or ClearQAM cable channels from a direct

Cable TV connection.

2

Remove the four (4) screws securing the
stand base to the HDTV. CAUTION: Hold the
stand firmly as you remove the last screw.

3

Use the screws that are threaded into the four
(4) inserts on the back of your HDTV to secure
it to an appropriate wall mounting kit.

VESA standard interface: 400 x 400

Mounting screws measurements:

M6 (6mm) Diameter, Length—12mm (maximum)

NOTE: Wall mounting kit is not included.

6

Need help? www.sanyoctv.com 1-877-864-9604

S-Video Input (VIDEO1)

NOTE: An S-Video connection will override a connection to

the Video1 (yellow) input jack.

Composite AV Input (VIDEO1) – Yellow (Video),
plus white and red (Audio) input jacks.

Component AV Input (VIDEO2) – Green (Y), blue
(Pb), and red (Pr) Video inputs plus the white and
red Audio inputs.

Stereo Audio Out (L/R) Jacks

HDMI (INPUT2 & 3) – An all digital AV interface

accepting uncompressed video signals up to
1080p for the best picture possible.

Analog / Digital Antenna Input – Connect a 75 OHM
cable from an antenna or direct Cable service.

Digital Audio Output (Coaxial)

AV Component Input (VIDEO3) – Green (Y), blue

(Pb), and red (Pr) Video inputs plus the white and
red Audio inputs.

NOTE: A Composite connection is possible via VIDEO

INPUT3 using the Y (VIDEO) jack and the L/R audio
jacks. (See Video 3 Setting on page 12.)

PC Input and Stereo Audio (Mini)

• MONITOR RGB (D-SUB)

• AUDIO R/L (Stereo Mini Jack)

NOTE: See page 18 for proper PC hookup and setup.

1

2

3

4
5

6

7
8

GETTING STARTED

HDTV INPUT/OUTPUT REFERENCE

1

3

4

2

6

7

8

9

10

11

12

USB Input

View pictures stored in a USB flash drive.
HDMI (INPUT1) – An all digital AV interface

accepting uncompressed video signals up
to 1080p for the very best picture possible.

NOTE: A DVI connection is possible via the HDMI

INPUT1 (DVI) using an appropriate adapter
and the VIDEO3 Audio jacks for sound output.

ETHERNET Port

Hook up your HDTV to the internet with the
use of an appropriate ethernet cable and a
correct internet setup.

NOTE: Please refer to the cTV Guide for the proper

connection to your Local Area Network (LAN).

9

10

11

12

HDTV BACK PANEL

HDTV

SIDE PANEL

5

7

Need help? www.sanyoctv.com 1-877-864-9604

GETTING STARTED

AUDIO / VIDEO CONNECTIONS (SIDE PANEL)

DVD PLAYER

(or similar device)

MULTICHANNEL RECEIVER

(or home theater system)

NOTE: Audio/Video cables

are not supplied.

COMPONENT connections will accept SDTV,
EDTV and HDTV video signals. Use them for great
image quality from digital devices such as a DVD
player or Video Game system.

Match your digital device’s Component output jacks
to either of the two (2) Component input jack sets
(VIDEO2 or VIDEO3) on your HDTV.

USB FLASH DRIVE

USB input jack is used to connect a USB mass
storage device to display digital images on your
HDTV. (JPEG only.)

DVI

HDMI (DVI) INPUT1 can be used to hookup a DVI

device with the use of an appropriate DVI to HDMI
cable or adapter. VIDEO3 Audio in L/R jacks need to
be hooked up to the DVI device as well

NOTE: HDMI INPUT1 may also be used to hookup any digital

device with an HDMI output, without the use of the L/R
audio jacks.

Digital Audio Output is used to output the HDTV’s
Audio through your home theater system.

Hook up the HDTV’s Digital Audio Output to your
home theater system’s input with the use of a
phono-type Digital Audio cable.

DVD PLAYER

(or similar device)

8

Need help? www.sanyoctv.com 1-877-864-9604

GETTING STARTED

AUDIO / VIDEO CONNECTIONS (BACK PANEL)

VCR

(or analog device)

STEREO AMPLIFIER

COMPOSITE connections are used to hookup
your analog equipment such as a VCR or an older
DVD player.

Hook up you analog device’s yellow video output
jack and corresponding audio output jacks to the
HDTV’s Video Input 1 composite jacks.

NOTE: Always match the color of your device’s output jack,

the connector and the HDTV’s input jack.

S-Video jack may be used instead of the yellow
Composite video input with the use of an S-Video
cable connected from your device’s S-Video out­put to the HDTV’s S-Video input.

SATELLITE RECEIVER

(or similar device)

Audio Output L/R are used to hookup an external
stereo Amplifier. Connect your home stereo’s
input jacks to the HDTV’s Audio Output jacks with
a pair of audio red and white connectors.

NOTE: Do not connect external speakers directly to the

HDTV.

Use HDMI INPUT1, 2 & 3 to hookup HD digital
devices such as a Blu-ray player, HD Cable Box,
HD Satellite Receiver or Video-game System.

Connect your digital device’s HDMI output to any
of the three (3) HDMI inputs on your HDTV with
the use of an HDMI cable.

HDMI

9

Need help? www.sanyoctv.com 1-877-864-9604

TURN ON TV (PRESS POWER BUTTON)

Wait for on-screen instructions to set an
Initial Energy Saving Mode, and perform an
Initial Channel/Signal Search.

PLUG IN AC POWER CORD

120V AC, 60Hz

GETTING STARTED (CONTINUED)

INITIAL CHANNEL SEARCH

Before proceeding, please make sure to hook up
your antenna or cable connection and all AV
equipment correctly to your HDTV.

Press the CH key to perform a channel
search from an Antenna or a direct Cable
connection, and a signal search from devices
hooked up to the HDTV’s AV input jacks.

AV INPUT SELECTION

Press the INPUT key to select the correct AV
input for the video source you wish to watch.

TV SET LOCATION SELECTION:

Select “Home Mode” by pressing the CH key to set
the HDTV’s backlight to an Energy Star qualified level,
or select “Store Mode” by pressing CH to set the
backlight to a retail display level.

CHANNEL AND AV SIGNAL SEARCH:

CHANNEL AND SIGNAL SETUP SCREEN

The final setup screen displays analog and digital
channels found as well as AV inputs detected. Pressing
the CH key finalizes the setup process.

NOTE: To repeat the initial setup process press VOL.

Press the CH key if you wish to access an
on screen trouble shooting guide.

NOTE: On screen help is also accesible via the

main menu.

ON SCREEN HELP (OPTIONAL)

INITIAL CHANNEL/SIGNAL SEARCH

SETUP SCREEN

CHANNEL SEARCH PROGRESS SCREEN

INITIAL ENERGY SAVING

MODE SCREEN

CHANNEL/SIGNAL LIST SCREEN

10

Need help? www.sanyoctv.com 1-877-864-9604

REMOTE CONTROL OPERATION

• MUTE Key—Mute or restore the sound.

• RECALL Key—Switch between current channel
and last selected channel.

• NET@ Key—Shortcut key to select the Net input
directly and display the Internet Entry screen.

• HDMI Key—Cycles through the HDMI inputs.

• USB Key—Selects the USB input directly.

• MENU Key—Displays or hides the on-screen
menu.

• HELP Key—Displays on-screen Help menu.

• LiNKS Key—Show or hide the available widgets.
Serves as a Home key for the content services
when navigating the Net input.

• EXIT Key—Exits the on-screen menu.
Return to the previous screen when navigating

the Net input.

• Cursor  (UP)  (DOWN) keys—Move the on­screen cursor up and down.

• Cursor  (LEFT)  (RIGHT) keys—Move the on­screen cursor left and right.

• ENTER Key—Set or select the highlighted option
on the screen.

The PLAY, PAUSE, STOP, REW, FF, W, T, CAMERA,
and XACTI MENU keys control playback features
on a Sanyo Xacti digital camera when the HDMI­CEC feature has been activated on both the HDTV
and the Xacti camera (see HDMI Linking feature
on page 12.)

NOTE: These playback keys may or may not react with

other devices other than the Xacti camera.

• POWER Key—Turns your HDTV On or Off.

• ECO Key—Modifies the Energy Saver level (see
page 13.)

• AUDIO Key—Selects the desired Audio mode.
Stereo, Mono, or SAP (when available.)

• ON TIMER Key—Displays the current switch on
time (see Clock Timer on page 14.)

• CAPTION Key—Cycles through the available
Caption modes.

• RESET Key—Pressing it twice restores your
HDTV to its factory settings. All user customized
settings will be cleared.

• SLEEP Key—Displays the “Off” Timer. While Off
Timer is on-screen, press the “0” key to Set the
amount of time (in 30 minute increments) at
which the HDTV will turn off.

• PIX SHAPE Key—Cycles through the available
aspect ratios. The different settings either
stretch, zoom, or fill the image on your screen.
Bars may appear on top and bottom of your
screen (or on left and right sides) depending on
the broadcasted signal or program.

NOTE: Pix6-7 are setup as Pix1-2 in PC mode. Use of
Pix6-7 in TV mode is not recommended.

• INFO Key—Displays the Channel Information
banner.

• NUMERICAL Keys—Select channels directly.

NOTE: For channels 100 and up, press and hold the
first number, then enter the remaining two numbers.

• ––(sub ch) Key —Allows for the direct selection
of digital subchannels. For example: to select
channel 39.1 press the

3, 9,

––

, and 1 keys.

• INPUT Key—Selects the video source to view.
Holding down the key displays the Input List.

• Volume

++

––

Keys—Increases or decreases the

audio level.

• Channel Keys—Scan through the channels
in the memory database.

CHANNEL / INPUT ____________

11

Need help? www.sanyoctv.com 1-877-864-9604

Auto – Searches the detected mode, Cable or Air.
Cable – Searches for analog and unscrambled

(ClearQAM) digital cable channels.
Air (Antenna) – Searches for analog and digital off-air

channels.
Digital Add-On – Searches digital off-air channels

adding newly found digital channels to the channel
map database.

Channel Search

Display the On Screen menu and use the
CURSOR  keys to select Channel / Input.
Press ENTER.

NOTE: Digital Add-On option is not available when the

current mode is Cable.

ON-SCREEN MENU OPERATION

Channel Scan Memory lists all Analog and Digital
channels found. It also lists Analog channels that were
not found, which can be added.

Use the CURSOR  keys to move the channel select
bar throuh all enabled and disabled channels, or use
the CH  keys to skip all disabled channels.

Press ENTER to enable or disable the selected channel.

Channel Scan Memory

NOTE: For information on local digital channels, visit

www.antennaweb.org

IMPORTANT FACT: This HDTV maintains only one database of
digital channels. Therefore, when you search for cable chan­nels, the database of antenna digital channels will be deleted.
You will only be able to receive those ClearQAM channels your
cable company provides.

Input Setting

CHANNEL SCAN MEMORY SCREEN

INPUT SETTING SCREEN

MAIN MENU SCREEN

CHANNEL SETTING SCREEN

Input Setting feature allows the removal of unused
inputs from the AV input loop.

Use the CURSOR  keys to select an AV input. Press
ENTER to disable (uncheck) or enable (check) the high­lighted input.

NOTE: At least one input must and will remain enabled.

:Skip is for reference only.

12

Need help? www.sanyoctv.com 1-877-864-9604

ON-SCREEN MENU OPERATION

Use this feature to establish either a Component or
Composite connection to the VIDEO INPUT 3 jacks on
your HDTV.

Use the CURSOR  keys to select the type of hook up
that will be used in the Video3 input.

Press ENTER, a blue mark will appear next to the
selected option.

Video3 Setting

With a Sanyo Xacti Digital Video/Movie
Camera hooked up to your HDTV’s
HDMI input, setting the HDMI-CEC
Function to ON enables you the use of
keys on your GXEB remote to operate
your Xacti camera.

Xacti-LINK

NOTE: The HDMI-CEC function of the Xacti camera must also

be turned ON to enable the Xacti-Link.

NOTE: Designed for use with a Sanyo Xacti Digital

VIdeo/Movie Camera, and may not support all HDMI­CEC functions of other equipment.

Use the HDMI-CEC Function to enable or disable all
available CEC functions.

HDMI Power ON Sync and Power OFF Sync enable
specific features including the automatic power ON
process and power OFF process.

HDMI Linking

HDMI LINKING SCREEN

VIDEO3 SETTING SCREEN

CHANNEL SETTING ___________