Sanyo DP50843 Quick Start Manual
Please READ and REMOVE this guide before operating your HDTV!
Part No. 1JC6P1P0437--
QUIK ‘N EASY
Setup Guide
Simple step by step procedures for correct HD hookups
and initial setup process.
Attach the Foot Stands to the HDTV.
Please use the longer M6 (6x30) screws included in the literature package.
For additional information, consult your HDTV’s owner’s manual.
Hook up your Audio/Video equipment to the HDTV.
Use Component or HDMI connections, and a High Definition source
for the best picture possible. Your AV equipment Output Jacks
must be connected to the HDTV’s Input Jacks. Always match the
color of the jacks and connectors.
Hook up your antenna or direct Cable service.
An indoor antenna should be placed at least 3 ft away from the HDTV.
EXPERIENCE THE BEST IMAGE QUALITY ON YOUR HDTVEXPERIENCE THE BEST IMAGE QUALITY ON YOUR HDTV
EXPERIENCE THE BEST IMAGE QUALITY ON YOUR HDTV
CONNECTION TYPE CABLE/CONNECTOR IMAGE QUALITY
Video Input 2
2
1
Antenna or
direct Cable service
DIGITAL
AUDIO
OUTPUT
Video Input 1
Off-air HD signal or Digital Cable
HDMI
BEST
BEST
BETTER
GOOD
For the best HD experience, be sure to use HD devices and/or HD off-air
signals transmitting HD content.
AUDIO
OUTPUT
Connect the AC cord to power outlet.
Use the POWER key to turn on your HDTV.
Finalize the completed Setup process.
Use the CURSOR keys to highlight the Finish Setup
option and press the ENTER key.
You can now watch and enjoy TV programming on your HDTV!
Channel Search Result: Succesfully Completed
Use the on-screen menu to select your HDTV’s location.
Use the CURSOR keys to highlight the desired option and press
the ENTER key.
Please select proper location for your TV,
display will be adjusted fo best results.
Store mode is for the
retail display setup.
Backlight set for high
brightness.
STORE
STORE
Store
Use keys to highlight your choice and then press ENTER key.
Home mode is for
household setup.
Backlight set to lower
energy consumption.
Home
Analog Channels
Video 1 Video 2 HDMI 1 HDMI 2
Finish Setup
If you are having problems, call us toll-free at 1-800-877-5032
Use keys to highlight your choice and then press ENTER key.
Digital Channels16 26
Repeat
Choose the correct Input source.
Use the INPUT key on your remote control to select
from the available Input sources on your HDTV.
NOTE: If you receive Satellite or Cable service
through a set top box, tune to the correct input on
your HDTV and use the receiver and its remote for
channel viewing.
Si necesita ayuda en ESPAÑOL, marque al 1-800-877-5032 y un asesor
estará dispuesto a ofrecerle ayuda con cualquiera de sus dudas.
Perform a Signal search.
Use the CURSOR keys to highlight the Signal Search
option and press the ENTER key.
Please allow the HDTV a few minutes to complete the process.
2
POWER ON
1 2
Please connect all antennas
and signals to the jacks
and terminals.
Signal search
Use keys to highlight your choice and then press ENTER key.
HDMI, the HDMI Logo, and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
Make sure all of your
equipment is switched on.
Skip
Use the following codes to program your cable or satellite provider’s
remote control to work with your new HDTV.
Direct TV
Dish Network
Comcast
Cox
Verizon
ATT
10154, 960
590, 683, 589, 542, 652
10154
0154, 0088
0181, 0826, 0920
1045, 1062, 1095, 1380
(to activate INPUT feature)
NOTE: If these do not work, refer
to your Cable or Satellite manual.
Loading...