Sanyo DC-DA1100 (XE) Service Manual

Page 1
Service Manual
FILE NO.
Micro Component System
DC-DA1100 (XE)
PRODUCT CODE No. 129 694 01
REFERENCE No.
SP: This service manual consists of "DC-DA1100U/XE" (Main unit : 129 693 01) and
"SX-DA1100/XE" (Speaker system : 165 104 01).
Contents
Laser beam safety precaution .......................................... 1
Tape adjustments ............................................................ 1
Tuner adjustments ........................................................... 2
CD pick-up maintenance .................................................. 2
Exploded view
(Cabinet & Chassis) ...................................................... 3
Parts list ........................................................................... 4
Exploded view & Parts list (Tape mechanism) ................ 7
IC block diagram & description ........................................ 7
LCD display description ................................................... 14
Wiring connection ............................................................ 15
CD
Schematic diagram
(FRONT) ....................................................................... 16
(CD)...............................................................................18
(TUNER) ....................................................................... 22
(AMPLIFIER ) ................................................................ 26
Wiring diagram
(FRONT & CD) .............................................................. 20
(TUNER) ....................................................................... 24
(AMPLIFIER) ................................................................. 28
(POWER TRANSFORMER & KEY) .............................. 30
Page 2
- 1 -
LASER BEAM SAFETY PRECAUTION
• Pick-up that emits a laser beam is used in this CD player section.
TAPE ADJUSTMENTS
R / P HEAD
RED
WHITE
YELLOW EARTH
b. Adjusting head azimuth
1. Load a test tape (VTT-738, etc. :10kHz) for azimuth adjustment.
2. Press the PLAY button.
3. Use a cross-tip screwdriver to turn the screw for normal azimuth adjustment so that the left and right outputs are maximized at the same phase during normal playback.
4. Press the STOP button.
1
2
3
4
4
MOTOR SPEED ADJUSTMENT
c. Adjusting motor speed
1. Insert the test tape (MTT-111 or etc. 3,000 Hz).
2. Press the PLAY button.
3. Use a flat-tip screwdriver to turn the SVR to adjust so that the frequency counter becomes 3,000 Hz.
4. Press the STOP button.
d. Replacing the moto
e. Checking the mechanism torques
• Clean the head, capstan and pinch roller before making any measurement.
Measurement Take-up torque Back tension Tape tension
Cassette for PLAY : TW-2111A PLAY : TW-2111A Drive-power cassette
measurement F.FWD/REW : TW-2231 TW-2412
PLAY 30 ~ 70gr.cm 1.0 ~ 6.0gr.cm 80 gr or more
F.FWD/REW 55 gr or more - -
CAUTION – INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM. ADVARSEL – USYNLIG LASER STRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION, UNDGÅ UDS ÆTTELSE FOR STRÅLING. VARNING – OSYNLIG LASER STRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRR ÄR URKOPPLAD. STRÅLEN ÄR FARLIG. VORSICHT – UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN DECKEL GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT IST. NICHT, DEM STRAHL AUSSETZEN. VARO – AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄ
TEESEEN.
CAUTION :
THIS PRODUCT CONTAINS A LOW POWER LASER DEVICE, TO ENSURE CONTINUED SAFETY DO NOT REMOVE ANY COVERS OR ATTEMPT TO GAIN ACCESS TO THE INSIDE OF THE PRODUCT. REFER ALL SERVICING TO QUALIFIED PERSONNEL.
LASER OUTPUT ..............0.6 mW Max. (CW)
WAVELENGTH ..................790 nm
a. Replacing the head
1. After replacement, demagnetize the heads by using a degausser.
2. Be sure to clean the heads before attempting to make any adjustments.
3. Be sure both channels (1 and 2) are the same level. (Using a dual-channels oscilloscope).
4. All wiring should be returned to the original position after work is completed.
Page 3
- 2 -
TUNER ADJUSTMENTS
E
MW ANT
E
E
E
T002A 94V-0
E
E
E
E
VT
L2205
XF212
IC201
XF211
CT211
Q2001
D2005
D2004
D2102
SH201
D2002
D2003
C2009
J2126
L2003
J2210
C2104
J2209
C2111
C2119
C2121
C2801
C2701
C2106
C2113
C2107
D2101
L2005
Q2101
L2006
J2203
J2206
J2119
C2312
C2108
Q2111
J2308
C2218
Q2201
J2115
J2205
S2001
J2208
CN201
L2002
1AD4B10D2411D
J2305
J2116 J2117
C2112
T2002
T2001
J2124
U
J2121
L2204
J2307
L2007
Q2002
D2104
CN203
Q2102
J2301
Q2110
J2202
XF215
J2302
R2129
CN202
J2118
J2111
J2125
J2113
J2303
J2120
J2304
J2306
CN204
XF210
J2114
D2105
J2123
Q2003
J2122
J2204
J2207
J2201
J2112
J2127
D2006
L2001
IC211
C2131
C2142
R2131
C2024C2005
C2002
R2001
C2001
C2001
C2014
C2014
C2022
C2022
C2001
R2002
C2014
R2005
C2013
R2004
R2003
C2011
C2011
C2015
C2015
R2008
R2008
C2117
C2117
C2122
C2122
C2702
C2702
R2801
R2801
R2701
R2701
C2115
C2115
R2301
R2301
C2114
C2114
R2303
R2303
R2302
R2302
C2120
C2120
C2011
C2012
C2008
C2015
R2014
C2017
C2003
C2003
C2101
C2101
C2802
C2802
C2209
C2209
C2311
C2311
C2003
R2006
R2008
R2007
R2009
C2021
R2101
C2101
C2118
C2117
C2122
C2702
C2802
R2801
R2701
C2103
C2103
R2106
R2106
R2126
R2126
R2910
R2910
C2902
C2902
C2103 C2102
R2104
R2106
C2110
C2126
R2113
R2113
R2900
R2900
R2113
R2117
R2119
C2209
C2020
C2019
C2311
C2207
R2128R2127
R2206
R2201
C2027
C2140
C2025
R2126
C2026
C2115
R2301
C2114
R2303
R2302
R2105
C2010
R2205
C2022
C2029
R2901
R2010
R2011
R2210
R2107
R2910
C2141
R2900
C2902
C2120
L2002 L2205
L2204
TP11
TP24TP25
TP12
TP13
TP14
TP15
T2001
CT211
IC211
T2002
Antenna : 75Ω unbalanced direct, Modulation : 1 kHz Dev. : ±22.5kHz(MONO), ±22.5kHz(MAIN), ±6.75kHz(PILOT) RF Level : dBuV EMF Output Level : about 30mV at TP13, TP14, TP15
Anntena : IRE Loop(SG), Moduration : 1kHz 30% RF Level : dBuV EMF Output Level : about 30mV at TP13, TP14, TP15
CD PICK-UP MAINTENANCE
About pick-up (Optical lens) Cleaning
Clean a lens with swab of the cotton which moistened it with alcohol, cleaning paper or cleaning disc appointed.
Specified cleaning disc : LC-1 (Part code : 645 026 1961 ..... manufactured by SANYO.)
Show a clean procedure in the following in reference by swab of cotton.
1. Cotton swab is wrapped with Cleaning paper.
2. Add the isopropyl alcohol.
3. Gently move the tip of cotton swab just like a draw a whirlpool from inside to outside on the surface of lens.
• Use a plastic screw driver for adjustments.
• MODE : ST (Stereo)
• Speaker impedance : 4 ohms
• TUNING FM : 87.5 - 108MHz AM : 522 - 1611kHz
1. FM
Connection
Input Output
Alignment voltage IC211 Alignment voltage IC211
3-22pin(TP24,25) is 0.0±0.05V 3-22pin is 0.0±0.05V
--- Connect Digital DC voltmeter to 87.5MHz
L2002
1.00±0.05V
--- TP11(H), TP12(E). 108.0MHz --- 5.10±0.50V Check Only
2. AM
Connection
Input Output
Connect Sweep generator to test
point TP13(L), TP14(R) and TP15(E).
--- Connect Digital DC voltmeter to 522kHz
L2205
1.00±0.05V
--- TP11(H )and TP12(E). 1611kHz --- 7.10±0.50V Check Only
Connect to VTVM 603kHz L2204 point TP13(L), TP14(R) and TP15(E).
1404kHz CT211
Remark
Remark
SG
Frequency
Adjustment
Adjustment
T2002
Step
Step
Adjusting
Circuit
Adjusting
Circuit
3
FM Antenna SG=66dBuV
IF
Adjustment
Loop Ant
1
2
1
Tracking
2
IF(0V)
Adjustment
Maximum
98.0MHz
Cover
Voltage
450kHz
at 999kHz
T2001
MaximumLoop Ant
SG
Frequency
Cover
Voltage
Page 4
- 3 -
EXPLODED VIEW (CABINET & CHASSIS)
20
19
10
9
12
25
26
27
28
30
31
32
33
29
8
6
7
11
22
2
13
14
15
17
18
16
3
4
5
1
23
53
21
22
22
24
Y03
Y01
Y02
Y05
Y05
Y04
Y04
Y05
Y06
Y07
55
56
51
52
54
Y11
Y11
Y12
Y14
Y13
Y15
Y15
Y16
Y16
Y19
Y19
Y21
Y20
Y20
Y18
Y18
Y17
Y13
Y08
Y09
Y10
Y10
Y10
Y09
Y07
Y07
71
72
73
74
75
76
57
58
This is a basic exploded view.
Page 5
- 4 -
PARTS LIST
CAUTION : Regular type resistors and capacitors are not listed. To know those values, refer to the schematic diagram.
Regular type resistors are less than 1/4 W carbon type and 0 ohm chip resistors. Regular type capacitors are less than 50 V and less than 1000 µF type of Ceramic type and Electrical type.
N.S.P : Not available as service parts.
PRODUCT SAFETY NOTICE
EACH PRECAUTION IN THIS MANUAL SHOULD BE FOLLOWED DURING SERVICING. COMPONENTS IDENTIFIED WITH THE IEC SYMBOL
!
!!
IN THE PARTS LIST AND THE SCHEMATIC DIAGRAM DESIGNATED COMPONENTS IN WHICH SAFETY AND
PERFORMANCE CAN BE OF SPECIAL SIGNIFICANCE. WHEN REPLACING A COMPONENT IDENTIFIED BY
!
!!
, USE ONLY THE REPLACEMENT PARTS DESIGNATED, OR PARTS WITH THE SAME RATINGS OF RESISTANCE, WATTAGE OR VOLTAGE THAT ARE DESIGNATED IN THE PARTS LIST IN THIS MANUAL. LEAKAGE-CURRENT OR RESISTANCE MEASUREMENTS MUST BE MADE TO DETERMINE THAT EXPOSED PARTS ARE ACCEPTABLY INSULATED FROM THE SUPPLY CIRCUIT BEFORE RETURNING THE PRODUCT TO THE CUSTOMER.
REF.NO. PART NO. DESCRIPTION
PACKING & ACCESSORIES
REF.NO. PART NO. DESCRIPTION
614 330 3848 CARTON CASE 614 329 2494 CUSHION,REAR 614 329 2487 CUSHION,FRONT 614 330 3893 INSTRUCTION MANUAL 614 330 4272 INSTRUCTION SHEET,GREECE 645 046 8322 ASSY,ANTENA,LOOP 614 325 5741 LID,BATTERY,SERVICE 645 057 4559 REMOCON,RB-DA1000 614 330 3602 ASSY,BOX,SPEAKER
CABINET & CHASSIS
REF.NO. PART NO. DESCRIPTION
1 614 329 2098 ASSY,DOOR,DECK 2 614 329 2449 SPRING,DOOR DECK 3 614 329 2258 KNOB,VOLUME 4 614 329 2111 ASSY,PANEL FRONT 5 614 309 7969 ASSY,GEAR,CASSETTE 6 614 329 2210 DEC,WINDOW BUTTON,STOP 7 614 329 6690 DEC,WINDOW BUTTON,
PLAY/PAUSE
8 614 329 6706 DEC,WINDOW BUTTON,
SKIP/SEARCH 9 614 329 2142 BUTTON,TOP,4 KEYS 10 614 329 2159 BUTTON,LEFT,3 KEYS 11 614 329 2135 BUTTON,FUNC,4 KEYS 12 614 329 2166 BUTTON,RIGHT,2 KEYS 13 614 329 2265 KNOB,DECK MECHA,REC 14 614 329 2272 KNOB,DECK MECHA,PLAY 15 614 329 2289 KNOB,DECK MECHA,REW 16 614 329 2296 KNOB,DECK MECHA,FFWD 17 614 329 2302 KNOB,DECK MECHA,STOP/EJECT 18 614 329 2319 KNOB,DECK MECHA,PAUSE 19 614 329 2340 MOUNTING,DECK MECHA 20 614 308 0534 SPRING,PLATE,REC 21 614 310 3899 SPACER,MECHA,CD+DA11 22 614 325 6014 ASSY,MECHA,DA11T3CN-SASH 23 614 307 2072 COVER,PICK-UP 24 614 322 2132 ASSY,GEAR,LID,CD 25 614 329 2357 MOUNTING,CD 26 614 303 0263 LATCH,PUSH,CD DOOR LOCKING 27 614 307 8821 PULLEY 28 614 303 0256 LATCH,MAGNET 29 614 329 2456 SPRING,DOOR CD 30 614 329 2333 LID,CD 31 614 329 2234 DEC,WINDOW CD 32 614 316 1172 STOPPER 33 614 330 3640 ASSY,CABINET,REAR
FIXING PARTS
REF.NO. PART NO. DESCRIPTION
Y01 411 187 2709 SCR S-TPG BIN 2.3X6,
BUTTON TOP+PWB TOP
Y02 411 021 6405 SCR S-TPG BIN 3X8,
BUTTON TOP+PANEL FRONT Y03 411 020 8905 SCR S-TPG BRZ+FLG 3X10,GEAR Y04 411 021 3503 SCR S-TPG BIN 3X10,
PANEL+MTG DECK KNOB
ELECTRICAL PARTS
REF.NO. PART NO. DESCRIPTION
51 614 309 8454 ASSY,WIRE,CD TO CD MECH 52 614 330 3459 FLEXIBLE FLAT CABLE,CD PICK UP 53 423 016 7908 FUSE 250V 2.5A 54 614 330 3466 FLEXIBLE FLAT CABLE,
FRONT TO AMP
55 614 330 3442 FLEXIBLE FLAT CABLE,
TUNER TO FRONT 56 614 274 2013 CORD,ID CONNECTOR,FM ANT 57 645 066 5646 TRANS,POWER 58 645 016 9939 CORD,POWER-1.74MK
FRONT P.W.BOARD ASSY
REF.NO. PART NO. DESCRIPTION
71 614 330 3305 ASSY,PWB,FRONT(Only initial) BR601 614 329 2241 HOLDER,LCD C6200 403 259 0508 NP-ELECT 1U M 50V or 403 373 7001 NP-ELECT 1U M 50V CN601 645 059 0474 SOCKET,FPC 14P,FRONT-AMP CN602 645 059 0498 SOCKET,FPC 16P CN603 645 005 7366 PLUG,2P
Y05 411 021 3503 SCR S-TPG BIN 3X10,
PANEL+DECK MECHA Y06 411 126 1404 SCR S-TPG BIN 2X4,
SPRING DECK REC Y07 411 021 3503 SCR S-TPG BIN 3X10,
FRONT PWB+MOUNT Y08 411 021 3503 SCR S-TPG BIN 3X10,
MTG CD+CD PCB Y09 411 021 1806 SCR S-TPG BIN 2.6X10,
MTG CD+MECHA CD Y10 411 092 0906 WASHER Z 2.6X10X0.5,
MECHA,CD+MOUNTING Y11 411 021 3503 SCR S-TPG BIN 3X10,
MTG CD+TUNER PCB Y12 411 021 3503 SCR S-TPG BIN 3X10,
MTG CD+ASSY,GEAR Y13 411 021 4906 SCR S-TPG BIN 3X20,
PANEL+MOUNTING Y14 411 021 3503 SCR S-TPG BIN 3X10,
MTG CD+AMP PCB Y15 411 021 3503 SCR S-TPG BIN 3X10,
REAR+PWB POWER Y16 411 020 9100 SCR S-TPG BRZ+FLG 3X12,
REAR+P-TRANS Y17 411 021 3503 SCR S-TPG BIN 3X10,
REAR+STOPPER Y18 411 098 7800 SCR S-TPG FLT 3X12,
PANEL+REAR+MOUNTING Y19 411 021 4500 SCR S-TPG BIN 3X16,PANEL+REAR Y20 411 021 3503 SCR S-TPG BIN 3X10,
MTG CD+REAR Y21 411 021 3503 SCR S-TPG BIN 3X10,
C-REAR(ANT TERMINAL)
Page 6
- 5 -
PARTS LIST
REF.NO. PART NO. DESCRIPTION
REF.NO. PART NO. DESCRIPTION
KEY P.W.BOARD ASSY
REF.NO. PART NO. DESCRIPTION
72 614 329 4153 ASSY,PWB,KEY(Only initial) CN604 614 330 3367 ASSY,WIRE,KEY-TU S6003 614 220 5471 SWITCH,TACT or 614 240 1002 SWITCH,TACT or 645 006 5958 SWITCH,PUSH 1P-1T or 645 048 3820 SWITCH,PUSH S6004 645 048 3820 SWITCH,PUSH or 645 006 5958 SWITCH,PUSH 1P-1T or 614 240 1002 SWITCH,TACT or 614 220 5471 SWITCH,TACT
CD P.W.BOARD ASSY
REF.NO. PART NO. DESCRIPTION
73 614 329 4122 ASSY,PWB,CD(Only initial) CN111 645 059 0498 SOCKET,FPC 16P CN113 645 005 8127 PLUG,6P CN122 645 005 8134 PLUG,8P CN123 614 326 6938 ASSY,WIRE D1401 407 012 4406 DIODE 1SS133 D1402 407 012 4406 DIODE 1SS133 D1403 407 012 4406 DIODE 1SS133 D1404 407 099 5204 ZENER DIODE MTZJ5.1B D1410 407 098 3300 DIODE RL153-BF-S2 IC101 409 503 5701 IC LA9242M-MPB IC102 409 539 9704 IC LC78629E IC103 409 486 8706 IC MM1469XH L1451 645 001 4550 INDUCTOR,10U K PR140 645 066 9668 PROTECTOR,0.4A 125V Q1301 405 008 7301 TR 2SB810-F or 405 008 7202 TR 2SB810-E or 405 008 6809 TR 2SB808-F-SPA or 405 008 7103 TR 2SB808-G-SPA Q1401 405 009 5306 TR 2SB927-T or 405 009 5207 TR 2SB927-S or 405 141 3604 TR KTA1273-Y X1451 645 057 1145 OSC,CERAMIC 16.93MHZ or 614 231 2667 RESONATOR
TUNER P.W.BOARD ASSY
REF.NO. PART NO. DESCRIPTION
74 614 330 3312 ASSY,PWB,TUNER(Only initial) CN201 645 038 7715 TERMINAL or 645 025 4703 TERMINAL,ANTENNA CN202 645 059 0498 SOCKET,FPC 16P CN203 614 221 8273 TERMINAL CN204 645 005 7366 PLUG,2P CT211 645 032 5663 TRIMMER,7PF D2002 407 157 8109 VARACTOR DI SVC211-B D2003 407 157 8109 VARACTOR DI SVC211-B D2004 407 012 4406 DIODE 1SS133 D2005 407 012 4406 DIODE 1SS133 D2006 407 012 4406 DIODE 1SS133 D2101 407 012 4406 DIODE 1SS133 D2102 407 105 1602 VARACTOR DI SVC342M-V or 407 105 1305 VARACTOR DI SVC342L-V D2104 407 099 5303 ZENER DIODE MTZJ5.6B D2105 407 012 4406 DIODE 1SS133 IC201 409 016 0200 IC LA1186N-AUDIO IC211 409 474 3201 IC LA1844ML L2001 645 040 2753 INDUCTOR,AIR — L2002 645 040 2746 COIL,AIR — L2003 645 002 1534 INDUCTOR,8.2U K L2005 645 002 1459 INDUCTOR,22U K L2006 645 002 1459 INDUCTOR,22U K L2007 645 002 1459 INDUCTOR,22U K L2204 645 037 2377 TRANS,ANT,796KHZ or 645 058 8792 TRANS,ANT,796KHZ L2205 645 040 2739 TRANS,OSC,796KHZ or 645 058 8822 TRANS,OSC,796KHZ Q2001 405 151 4301 TR KTC3195-Y or 405 151 4806 TR KTC3195-O
D6901 407 012 4406 DIODE 1SS133 D6902 407 012 4406 DIODE 1SS133 D6951 407 235 7406 LED LT7V34-81-URC1,LCD-LIGHT D6952 407 235 7406 LED LT7V34-81-URC1,FRONT-LIGHT IC601 410 517 4208 IC LC72338-9C41-E,MICON L6900 645 001 4550 INDUCTOR,10U K L6901 645 001 4550 INDUCTOR,10U K LC601 614 329 2180 COVER,LED LCD60 645 066 5653 LCD LR601 614 329 2395 REFLECTOR,LCD LS601 614 329 6720 DEC,SHEET LCD Q6200 405 143 8706 TR KTC3199-GR or 405 011 8500 TR 2SC1740S-R or 405 011 8609 TR 2SC1740S-S or 405 017 9600 TR 2SC3330-T or 405 017 9709 TR 2SC3330-U Q6201 405 143 8706 TR KTC3199-GR or 405 011 8500 TR 2SC1740S-R or 405 011 8609 TR 2SC1740S-S or 405 017 9600 TR 2SC3330-T or 405 017 9709 TR 2SC3330-U S6001 614 220 5471 SWITCH,TACT or 614 240 1002 SWITCH,TACT or 645 006 5958 SWITCH,PUSH 1P-1T or 645 048 3820 SWITCH,PUSH S6002 614 240 1002 SWITCH,TACT or 645 006 5958 SWITCH,PUSH 1P-1T or 645 048 3820 SWITCH,PUSH or 614 220 5471 SWITCH,TACT S6007 614 240 1002 SWITCH,TACT or 614 220 5471 SWITCH,TACT or 645 006 5958 SWITCH,PUSH 1P-1T or 645 048 3820 SWITCH,PUSH S6008 614 220 5471 SWITCH,TACT or 614 240 1002 SWITCH,TACT or 645 006 5958 SWITCH,PUSH 1P-1T or 645 048 3820 SWITCH,PUSH S6009 614 220 5471 SWITCH,TACT or 614 240 1002 SWITCH,TACT or 645 006 5958 SWITCH,PUSH 1P-1T or 645 048 3820 SWITCH,PUSH S6010 645 006 5958 SWITCH,PUSH 1P-1T or 645 048 3820 SWITCH,PUSH or 614 240 1002 SWITCH,TACT or 614 220 5471 SWITCH,TACT S6011 614 220 5471 SWITCH,TACT or 614 240 1002 SWITCH,TACT or 645 006 5958 SWITCH,PUSH 1P-1T or 645 048 3820 SWITCH,PUSH S6012 614 220 5471 SWITCH,TACT or 614 240 1002 SWITCH,TACT or 645 006 5958 SWITCH,PUSH 1P-1T or 645 048 3820 SWITCH,PUSH S6013 614 220 5471 SWITCH,TACT or 614 240 1002 SWITCH,TACT or 645 006 5958 SWITCH,PUSH 1P-1T or 645 048 3820 SWITCH,PUSH S6500 645 057 4535 SWITCH,ROTARY(ENCODER) SE601 407 220 6803 PHOTO DIODE SPS-444-1-G1 X6001 645 052 6206 OSC,CRYSTAL 4.5MHZ
S6005 614 220 5471 SWITCH,TACT or 614 240 1002 SWITCH,TACT or 645 048 3820 SWITCH,PUSH or 645 006 5958 SWITCH,PUSH 1P-1T S6006 614 220 5471 SWITCH,TACT or 614 240 1002 SWITCH,TACT or 645 006 5958 SWITCH,PUSH 1P-1T or 645 048 3820 SWITCH,PUSH
Page 7
- 6 -
PARTS LIST
REF.NO. PART NO. DESCRIPTION REF.NO. PART NO. DESCRIPTION
AMPLIFIER P.W.BOARD ASSY
REF.NO. PART NO. DESCRIPTION
75 614 329 4108 ASSY,PWB,AMP(Only initial) C4714 403 058 4608 POLYESTER 0.15U J 50V C4814 403 058 4608 POLYESTER 0.15U J 50V C4913 403 350 9301 ELECT 3300U M 25V or 403 329 5907 ELECT 3300U M 25V C4918 403 377 6307 POLYESTER 1000P J 50V or 403 056 7502 POLYESTER 1000P J 50V CN401 645 006 1875 PLUG,2P,SPEAKER CN402 645 006 1875 PLUG,2P,SPEAKER CN405 645 004 2904 PLUG,4P CN406 645 005 8110 PLUG,4P CN411 645 004 2881 PLUG,2P,POWER CN421 645 055 1017 JACK,PHONE D3.6,HEADPHONE or 645 011 6384 JACK,PHONE D3.6,HEADPHONE CN490 645 012 2736 SOCKET,DIP 8P CN491 645 059 0474 SOCKET,FPC 14P CN492 614 314 4809 ASSY,WIRE or 614 309 8812 ASSY,WIRE D4102 407 012 4406 DIODE 1SS133 D4951 407 099 6003 ZENER DIODE MTZJ9.1B D4953 407 012 4406 DIODE 1SS133 D4961 407 012 4406 DIODE 1SS133 D4962 407 012 4406 DIODE 1SS133 D4963 407 012 4406 DIODE 1SS133 D4980 407 098 3300 DIODE RL153-BF-S2 D4981 407 098 3300 DIODE RL153-BF-S2 D4982 407 098 3300 DIODE RL153-BF-S2 D4983 407 098 3300 DIODE RL153-BF-S2 D4993 407 012 4406 DIODE 1SS133 FCL41 645 006 4760 HOLDER,FUSE or 645 031 7903 HOLDER,FUSE FCL42 645 031 7903 HOLDER,FUSE or 645 006 4760 HOLDER,FUSE HS401 614 307 9866 HEAT SINK IC410 409 384 3506 IC BA3314F IC411 409 474 6103 IC LC75342M IC412 409 295 7402 IC TA8229K
POWER TRANSFORMER P.W.BOARD ASSY
REF.NO. PART NO. DESCRIPTION
76 614 329 4146 ASSY,PWB,PT(Only initial) CN451 614 017 8203 TERMINAL BOARD CN452 614 017 8203 TERMINAL BOARD CN455 645 005 9315 PLUG,2P L4591 645 041 3087 INDUCTOR,180U or 645 038 6053 INDUCTOR,181U
Q2002 405 151 4806 TR KTC3195-O or 405 151 4301 TR KTC3195-Y Q2003 405 017 9709 TR 2SC3330-U or 405 017 9600 TR 2SC3330-T or 405 011 8609 TR 2SC1740S-S or 405 011 8500 TR 2SC1740S-R or 405 143 8706 TR KTC3199-GR Q2101 405 151 5209 TR KRA107M or 405 000 0904 TR DTA114YS Q2102 405 000 3806 TR DTC114YS or 405 143 0007 TR KRC107M Q2110 405 000 3806 TR DTC114YS or 405 143 0007 TR KRC107M Q2111 405 151 4806 TR KTC3195-O or 405 151 4301 TR KTC3195-Y Q2201 405 000 0904 TR DTA114YS or 405 151 5209 TR KRA107M S2001 645 023 5795 SWITCH,LEVER SH201 614 256 3052 SHIELD T2001 645 043 0213 FILTER,450KHZ T2002 645 039 9923 TRANS,IF 10.7MHZ or 645 040 9981 TRANS,IF 10.7MHZ or 645 060 4089 TRANS,IF 10.7MHZ XF210 645 059 0047 FILTER,BP or 645 026 2975 FILTER,BP 108MHZ or 614 252 1045 FILTER,LC XF211 645 054 1223 CERAMIC FILTER 10.70MHZ or 645 010 7665 CERAMIC FILTER 10.70MHZ or 614 240 2917 FILTER,CERAM XF212 645 054 1223 CERAMIC FILTER 10.70MHZ or 645 010 7665 CERAMIC FILTER 10.70MHZ or 614 240 2917 FILTER,CERAM
IC446 409 039 9204 IC NJM78L05A L4780 645 002 1459 INDUCTOR,22U K L4781 645 002 1459 INDUCTOR,22U K L4881 645 002 1459 INDUCTOR,22U K L4902 645 031 5893 TRANS,OSC,85KHZ,O.S.C LG401 645 006 4432 FIXER PR495 645 066 9767 PROTECTOR,1.25A 125V PR496 645 066 9743 PROTECTOR,1.5A 125V Q4103 405 110 5400 TR KRA102M-A or 405 000 0508 TR DTA114ES Q4104 405 000 3103 TR DTC114ES or 405 109 9204 TR KRC102M-A Q4106 405 109 9204 TR KRC102M-A or 405 000 3103 TR DTC114ES Q4108 405 143 0007 TR KRC107M or 405 000 3806 TR DTC114YS Q4740 405 109 9204 TR KRC102M-A or 405 000 3103 TR DTC114ES Q4751 405 033 6805 TR 2SD1468S-S or 405 033 6706 TR 2SD1468S-R or 405 021 0600 TR 2SD1012-G-SPA or 405 021 0204 TR 2SD1012-F-SPA or 405 151 4400 TR KTD1303 Q4840 405 109 9204 TR KRC102M-A or 405 000 3103 TR DTC114ES Q4851 405 151 4400 TR KTD1303 or 405 021 0204 TR 2SD1012-F-SPA or 405 021 0600 TR 2SD1012-G-SPA or 405 033 6706 TR 2SD1468S-R or 405 033 6805 TR 2SD1468S-S Q4902 405 143 8706 TR KTC3199-GR or 405 011 8500 TR 2SC1740S-R or 405 011 8609 TR 2SC1740S-S or 405 017 9709 TR 2SC3330-U or 405 017 9600 TR 2SC3330-T Q4903 405 017 9709 TR 2SC3330-U or 405 017 9600 TR 2SC3330-T or 405 011 8609 TR 2SC1740S-S or 405 011 8500 TR 2SC1740S-R or 405 143 8706 TR KTC3199-GR Q4904 405 017 9709 TR 2SC3330-U or 405 017 9600 TR 2SC3330-T or 405 011 8609 TR 2SC1740S-S or 405 011 8500 TR 2SC1740S-R or 405 143 8706 TR KTC3199-GR Q4951 405 095 1701 TR 2SD2061-F or 405 095 1602 TR 2SD2061-E or 405 138 6403 TR KTD2058Y or 405 158 2102 TR KTC2026-Y Q4992 405 008 2504 TR 2SB698-G or 405 008 2405 TR 2SB698-F or 405 141 3703 TR KTA1271-Y Q4994 405 000 3806 TR DTC114YS or 405 143 0007 TR KRC107M Q4995 405 008 2405 TR 2SB698-F or 405 141 3703 TR KTA1271-Y or 405 008 2504 TR 2SB698-G R4752 402 071 1304 FUSIBLE RES 2.2 JA 1/4W R4852 402 071 1304 FUSIBLE RES 2.2 JA 1/4W R4941 402 081 0205 FUSIBLE RES 27 JA 1/4W S4950 645 038 7586 SWITCH,PUSH,R/PSW SA401 411 021 6405 SCR S-TPG BIN 3X8 SA402 411 021 6405 SCR S-TPG BIN 3X8
Page 8
- 7 -
TM06
TM05
TM04
TM03
TM02
TM01
*
*
*
*
*
EXPLODED VIEW & PARTS LIST(TAPE MECHANISM)
* N.S.P : Not supplied as service parts.
EFMO VVDDVVSSPDO ISET FR PCK TAI
TST11
TEST1 TEST3 TEST5
TEST2 TEST4
VDDV
SS
C2F
DOUT
LV
DD
LV
SS
MUTER/
CONT8
LCHO MUTEL/ CONT7
RV
DD
RV
SS
RCHO
XV
DD
XOUT
XINFSX
XV
SS
4.2M16MEFLGEMPH/
CONT6
CONT5
CONT4
CONT3
CONT2
CONT1
TGL
*RESJP+JP-TOFFTESHFL
RWC
COIN
*CQCK
SQOUT
WRQ
SFSY
SBSY
SBCK
PW
V/*P
CLV-
CLV+
FSEQ
EFMIN
DEFI
10
22
1
12
13
14
49 51 47 50
53
55
57
56
54
15 16 17 20 19 58
PCLL
3418 24 25 26 27 28 29 48 60 61 46 52 45 44 43 39 41 35 40 37 42 38 36
31
30
9
21
6
4
357 2
59 64 11 32 33 62
8
VDD3V
63
23
Slice level
Control
Subcode
Separation
QCRC
Syncrnous Detection
EFM Demodulation
VCO Clock Oscillator
& Clock Control
Crystal Oscillator
System Generator
RAM Address
Generatorl
Digital Output
General
PurposePort
Digital Attenuator
8X Over Sampling
Digital Filter
Interpolalation
Mute
C1 C2 Error Detection&
Correction Flag
Processing
1bit DAC
L.P.F
CLV
Digital Servo
Micro-computer
Inter Fase
Servo Commander
2K
X
8bits
RAM
IC BLOCK DIAGRAM & DESCRIPTION
IC102 LC78629E (DSP for a CD Player)
TAPE MECHANISM
REF.NO. PART NO. DESCRIPTION
614 309 7976 ASSY,MECHA,TM-DA70TN-SH TM01 645 033 8625 E HEAD 6PA TM02 645 041 3025 R.P HEAD TM03 645 009 1612 PINCH ROLLER ARM ASSY TM04 645 009 1766 RF BELT TM05 645 033 3415 MAIN BELT TM06 614 312 0629 ASSY,MOTOR,FOR SERVICE
Page 9
- 8 -
IC BLOCK DIAGRAM & DESCRIPTION
Note) The same potential must be suplied to all power supply pins, i.e., VDD,VVDD,LVDD,RVDD and XVDD.
33
34
35
36
37
38
39
40
41
42
43 44
45 46
47
48
49
50
51
52
53 54
55
56
57
58
59
60
61
62
63
64
TEST4
PCCL
MUTEL/ CONT7
LVDD
LCHO
LVSS
RVSS
RCHO
RVDD
MUTER/ CONT8
XVDD XOUT
XIN XVSS
SBSY
EFLG
PW
SFSY
SBCK
FSX
WRQ RWC
SQOUT
COIN
*CQCK
*RES
TST11
16M
4.2M
TEST5
VDD3V
TEST1
I
I
O
-
O
-
-
O
-
O
-
O
I
-
O
O
O
O
I
O
O
I
O
I
I
I
O
O
O
I
-
I
Left channel mute output pin, General-purpose 7 output pin. Rest to MUTEL function.
Left channel power supply pin.
Left channel output pin.
Left channel ground pin. Must be connected to 0V.
Right channel ground pin. Must be connected to 0V.
Right channel output pin.
Right channel power supply pin.
Right channel mute output pin, General-purpose 8 output pin. Rest to MUTER function.
Lch one-bit DAC
Rch one-bit DAC
Crystal oscillator power supply pin.
Connections for a 16.934MHz crystal oscillating circuit ground pin.
Crystal oscillator ground pin. Must be connected to 0V.
Subcode block synchronization signal pin.
C1,C2,signal and double error correction monitor pin.
Subcode P,Q,R,S,T,U,V and W output pin.
Subcode frame synchronization signal output pin. This signal falls when the subcode are in the standby stase.
Subcode readout clock input pin. This is a Schmitt input. (Must be connected to 0V when unused.)
Output for the 7.35kHz synchronization signal divided from the crystal oscillator pin.
Subcode Q output standby output pin.
Read/ write control input pin. This is a Schmidt input.
Subcode Q output pin.
Command, data input pin from control microprocessor.
Input for both the command input acquisition clock and the SQOUT subcode readout clock input pin. This is Schmidt input.
Reset input pin. This pin must be set low briefly after power is first applied.
Test output pin. Leave open. (Notmally output a low level.)
16.9344MHz clock output pin.
4.2336MHz clock output pin.
Test input pin. A pull-down resistor is built in. Must be connected to 0V.
Internal circuit 3.3V system power supply pin.
Test input pin. A pull-down resistor is built in. Must be connected to 0V.
Test input pin. A pull-down resistor is built in. Must be connected to 0V.
General-purpose I/O command identification pin. A pull-down resistor is built in. Used operate similarly to LC78622E connected to open or 0V. H ; Must be connected to general-purpose port command. L ; Be able to all command control.
No. Symbol I/O Function description
Output pin
to rest
-
-
H output
-
-
-
-
-
-
H output
-
-
-
Incertitude
Incertitude
Incertitude
Incertitude
-
Incertitude
Incertitude
-
Incertitude
-
-
-
L output
Clock output
Clock output
-
-
-
Defect detection signal(DEF) input pin. (Must be connected to 0V when unused.)
PLL
Test input pin. A pull-down resistor is built-in. Must be connected to 0V.
Internal VCO ground pin.Must be connected to 0V.
External VCO control phase comparator output pin.
PDO output current adjustment resistor connection pin.
Internal VCO power supply pin.
VCO frequency range adjustment.
Digital system ground pin. Must be connected to 0V.
Slice level control
EFM signal output pin.
EFM signal input pin.
Test input pin. A pull down resistor is built in. Must be connected to 0V.
Disk motor control output. Can be set to three-value output by microprpcessor command.
Rough servo/phase control automatic switching monitor output pin. Outputs a high level during rough servo and a low level.
Track detection signal input pin. This is a Schmidt input.
Tracking error signal input pin. This is a Schmidt input.
Tracking off output pin.
Tracking gain switching output pin. Increase the gain when low.
Track jump output. Three-value output is also possible when specified by microprocessor command.
1
2
3
4
5
6
7
8
9
10
11
12 13
14
15
16
17
18
19 20
I
I
O
-
AI
-
AI
-
O
I
I
O O
O
I
I
O
O
O O
-
-
-
Incertitude
-
-
L output
L output
-
-
H output
Incertitude
L output
DEFI
TAI
PDO
VVSS
ISET
VVDD
FR
VSS
EFMO
EFMIN
TEST2
CLV+ CLV-
V/*P
HFL
TES
TOFF
TGL
JP+ JP-
No. Symbol I/O Function description
Output pin
to rest
EMF data playback clock monitor pin. Output 4.3218MHz when the normal-speed playback phase command.
Synchhronization signal detection output pin. Output a high level when the synchronization signal detected from the EFM signal and the internaly generated synchronization signal range.
Peripheral circuitry 5V system power suply pin.
General-purpose 1 input/output pin.
General-purpose 2 input/output pin.
General-purpose 3 input/output pin.
General-purpose 4 input/output pin.
General-purpose 5 input/output pin.
De-emphasis monitor pin. A high level indicates playback of a de-emphasis disk, General-purpose 6 output pin. Rest to EMPH function.
C2 flag output pin.
Digital output pin. (EIJA format)
Test input pin. A pull-down resistor is built in. Must be connected to 0V.
21
22
23
24
25
26
27
28
29
30
31
32
PCK
FSEQ
VDD
CONT1
CONT2
CONT3
CONT4
CONT5
EMPH/ CONT6
C2F
DOUT
TEST3
O
O
-
I/O
I/O
I/O
I/O
I/O
O
O
O
I
Controlled by serial data commands. From the microprocessor. Any of these that are unused must be either set up as input pin and connected to 0V, or set up as output pin and left open.
L output
Incertitude
-
Input
L output
Incertitude
Incertitude
-
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_______________
_
_______________
_
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
DEFI
TAI
PDO
VVSS
ISET
VVDD
FR
VSS
EFMO EFMIN TEST2
CLV+
CLV-
V *P HFL TES
EFLG SBSY XVSS XIN XOUT XVDD MUTER CONT8 RVDD RCHO RVSS LVSS LCHO LVDD MUTEL CONT7 PCCL TEST4
TOFF
TGL
JP+
JP-
PCK
FSEQ
VDD
CONT1
CONT2
CONT3
CONT4
CONT5
EMPH CONT6
C2F
DOUT
TEST3
TEST1
VDD3V
TEST5
4.2M
16M
TST11
*RES
*CQOUT
COIN
SQOUT
RWC
WRQ
FSX
SBCK
SFSY
PW
IC102 LC78629E (DSP for a CD Player)
Page 10
- 9 -
IC BLOCK DIAGRAM & DESCRIPTION
FSS
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
48
47
46
45
44
43
41
40
39
38
37
36
35
34
33
42
32313029282726252423222120191817
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Vcc1 LDS LDD BH1 PH1 LF2 VR REF1 Vcc2
DRF CE
DAT CL CLK DEF
NC
TBC
FSC
DGND
SLI
SLC
RFS-
RFSM
CV+
CV-
SLOF
HFL
TES
TOFF
TGL
JP+
JP-SL+SL-SLDSLEQSPDSP-SPGSPI
SP
AGND
FE-FE
FA-FAFD-
FD
TO
JP
TD
TD-
TA
TH
SCH
TESI
TE
TE-
TB
F
E
FIN1
FIN2
APC
RF DET
REF
VCA
I/V
BAL
VCA
INTER FACE
SLC
RF Amp
TE
T.SERVO & T.LOGIC
F.SERVO & F.LOGICK
SPINDLE SERVO
SLED SERVO
IC101 LA9242M-MPB (Servo Processing Signal for a CD Player)
Page 11
- 10 -
IC410 BA3314F (Dula Preamplifier with ALC Detector)
14
13
12
11
10
1
2
3
4
5
6
7
NF1
IN1
GND (SUB)
GND
Vcc
IN2
FILTER
ALC
ALC
NC
NC
NC
OUT 1
OUT 2
NF2
150k
150k
+
+
-
-
9
8
FM
IF
FM
DET
LEVEL
DET
S-CURVE
AM/FM
IF
BUFF
REG
GND
COMP
TUNING
DRIVE
AM
IF
AM
DET
VCC
AGC
PILOT
CANCEL
PILOT
DET
DECODER
ANTI-BIRDIE
STEREO
SW
FF
38k
FF
19k
VCO
304kHz
AM
RF.AMP
AM
MIX
AM
OSC
ALC
BUFF
P-DET
FF
19k
2
1
2345678910 11 12
24 23 22 21 20 19 18 17 16 15 14
13
IC211 LA1844ML (Tuner System)
CONTROL
CIRCUIT
LOGIC
CIRCUIT
CCB
INTERFACE
CONTROL
CIRCUIT
15
14
16
17
18
19
20
21 22 24 25 2623
10 9 7 6 58
11
L4
L3
L2
L1
NC
NC
R1
R2
R3
R4
RSELO RIN RTRE RBASS1 RBASS2 ROUT
LSELO LIN LTRE LBASS1 LBASS2 LOUT
TEST
V
SS
CE
DI
CL
V
DD
Vref
NC
12
13
1
2
30
29
28
27
4
3
LVref
RVref
IC411 LC75342M (Function SW / Electric Volume
/ 2 Band Equalizer)
IC412 TA8229K (Power Amplifier)
5
7
6
48
14 15
11 10
9
VCC1VCC2
IN-1
IN-2
NF1
NF2
RIPPLE
TERMINAL
B.S.1
B.S.2
OUT-1
OUT-2
POWER GND
Ch-1
-
+
3
2
12 13
Ch-2
-
+
PRE
GND1
PRE
GND2
BIAS CIRCUIT
THERMAL CUT-OFF
PROTECTION
IC BLOCK DIAGRAM & DESCRIPTION
Page 12
- 11 -
IC BLOCK DIAGRAM & DESCRIPTION
IC601 IC LC72338-9C41-E (Single-Chip PLL + Controller)
68
66 67
65
19 20
21
22
64
63
62
61
23
24
25
26
27
29
30
28
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
59
60
56
57
58
78
77 E01
E02 COM1 COM2 COM3
Vdd2
Vdd1
S1 S2 S3
S4 S5 S6 S7 S8 S9 S10 S11
S15
S12 S13 S14
S16
S17/PE0 S18/PE1/SCK2
S19/PE2/SO2 S20/PE3/SI2 S21/PF0 S22/PF1/SCK1 S23/PF2/SO1 S24/PF3/SI1
S28/PM3
S25/PM0 S26/PM1 S27/PM2
S29/PN0/BEEP
S31/PN2
S30/PN1
S32/PN3 PJ3/DAC3 PJ2/DAC2 PJ1/DAC1 PJ0/DAC0
PK3 PK2 PK1/INT1 PK0/INT0
PH3/ADI3 PH2/ADI2 PH1/ADI1 PH0/ADI0
1
80
74
XIN
XOUT
FMIN
75
72 73 76
70
71
AMIN
SNS
HOLD
VDD
VSS
HCTR
LCTR
69 79
2 18 17 16 15 14 13 12 11 10
9
8
7
TEST1
TEST2
PA 0 PA 1 PA 2 PA 3 PB0 PB1 PB2 PB3 PC0 PC1 PC2 PC3
6
5
4
3
PG0
SCK0/PG1
SO0/PG2
SI0/PG3
LATCH BUS DRIV.
LATCH BUS DRIV.
LATCH BUS DRIV.
SIO
BUS DRIV.
1 / 2
V-DET
SNSFF
1 / 16,1 / 17
PROGRAMMABLE DIVIDER
LATCH
UNIVERSAL COUNTER (20bits)
RAM
512 x 4bits
ROM
8K x 16bits
ADDRESS DECODER
BUS DRIVER
INSTRUC­TION DECODER
ADDRESS DECODER
PROGRAM COUNTER
STACK
JUDGE
ALU
DAC
ADC
LATCH BUS DRIV.
LATCH BUS DRIV.
LATCH BUS DRIV.
LATCH BUS DRIV.
LATCH BUS DRIV.
LATCH BUS DRIV.
LATCH BUS DRIV.
MPX
INTERRUPT
MPX
MPX
MPX
MPX
MPX
BEEP
LCPA/B
LCDA/B
SEG PLA
LATCH
LCD PORT DRIVER
96
4
4
7
SELECTER
PHASE DETECTOR
UNLOCK F/F
COMMON DRIVER
REFERENCE DIVIDERDIVIDER
Vref BUFFER
RF MIX REG OSC
RF IN GND IF OUT Vcc
1 2 3 4 5 6 7 8 9
IC201 LA1186N-AUDIO (FM Front End)
Page 13
- 12 -
IC BLOCK DIAGRAM & DESCRIPTION
IC601 IC LC72338-9C41-E (Single-Chip PLL + Controller)
Pin name Pin No. I/O I/O Format Functions
PA0 PA1 PA2 PA3
18 17 16 15
I
Pull-down resistor input
Port only for key return signal input. The threshold voltage is set to a relatively low value. When a key matrix is formed by combining PB and PC ports, maximum three simultaneous key presses can be detected. All of four pull-down resistor are set by the IOS instruction with Pn=2, b1 and specification of resistor for each pin is impossible. The input is disabled in clock stop mode.
PB0 PB1 PB2 PB3 PC0 PC1 PC2 PC3
14 13 12 11 10
9 8 7
O
Unbalance CMOS Push-pull
Port only for key source signal output. Since the output transistor circuit is an unbalanced CMOS structure, diodes to prevent short-circuiting due to multiple key presses are not required. In clock stop mode, these pins go to the output high-impedance state and hold this state until an output instruction is executed.
PG0
PG1/SCK0
PG2/SO0
PG3/SI0
6 5 4 3 I/O
CMOS posh-pull
General-purpose output/serial I/O ports. Schmidt type input the IOS instruction performs switching between general-purpose I/O ports and serial I/O ports, and between input and output for general-purpose I/O ports.
• When used as general-purpose I/O ports these pins can be set for input or output in bit units(bit I/O), and are set for use as general-purpose I/O por ts by the IOS instruction with Pn=0. b0=SI/O 0 0 • • • general-purpose port 1 • • • SI/O port Specification of input or output is made by the IOS instruction in bit units. PG • • • Pn=6 0 • • • Input 1 • • • Output
• When used as serial I/O ports these pins are set for serial I/O port use by the IOS instruction with Pn=0. The content of serial I/O data buffer is saved or load by the INR and OUTR instructions. *Pin setup states when used as serial I/O ports PG0 • • • general-purpose input or output PG1 • • • SCK0 output in internal block SCK0 input in external block PG2 • • • SO0 output PG3 • • • SI0 input In clock stop mode, input is disabled and these pins go to the high-impedance state. During the power-on reset, these pins become general-purpose input ports.
4.5MHz crystal oscillator pin.
XIN
XOUT1 80
EO1 EO2
78 77
O
CMOS tristate
-
I
O
Charge pump output pin. These pins go to high-impedance state when the HOLD pin is set low in the hold enable state. In ckock stop mode, during the power-on reset and in the PLL stop state, these pins go to the high-impedance state.
VSS VDD
FMIN
AMIN
HCTR
76
31,73
74
75
70
72
-
I
I
I
I
-Power supply pin.
FMVCO (local oscillator) input pin. This pin is selected by the PLL instruction CW1 (b1=0,b0=don't care). Capacitor coupling must be used for signalinput. Input is disabled when the HOLD pin is set low inthe hold enable state. Input is disable in clock stop mode,during the power-on reset, and in the PLL stop state.
AMVCo (lcal oscillator) input pin. This pin is selected and the band set by the PLL instruction CW1 (b1,b0).
Capacitor coupling must be used for signal input. Input is disabled when the HOLD pin is set low in the hold enable state. Input is disabled in clock stop mode, during the power-on reset, and in the PLL stop state.
b1 b0 Band 1 0 2 to 40MHz (SW) 1 1 0.5 to 10MHz (MW,NW)
Universal counter / general-purpose input port. The IOS instruction b3 with Pn=3 switches the pin function between universal counter input and general-purpose input.
• Frequency measurement The universal counter function is selected by an IOS instruction with Pn=3 and b2=0. HCTR frequency measure­ ment mode is set up by a UCS instruction with b3=0 and b2=0, and counting is started with a UCC instruction after the count time is selected. The CNTEND flag is set when the count completes. To operate this circuit as an AC amplifier in this mode, the input must be capacitor coupled.
• For use as the general-purpose input pin. The general-porpose input port function is selected by an IOS instruction with Pn=3 and b2=1. An internal register (address OEH) input instruction INR(b0) is used to acquire data from this pin. Input is disabled in clock stop mede (the input pin will be pulled down.) During the power-on reset, the universal counter function is selected.
SNS
Voltage sense / general-purpose input pin port. This circuit is designed for a relatively low input threshold voltage.
• For use as the voltage sense pin This input pin is is used to determine whether or not a power failure occurred after recovery from backup (clock stop) mode. An internal sense F/F is used for this determination. The sense F/F is tested with a TUL instruction (b2).
• For use as the general-purpose input port When used as a genaral-purpose input port, the state is sensed by using a TUL instruction (b3). Since unlike other input ports, input is not disablle in clock stop mode and during the power-on reset, special care is required with respect to through currents.
Pin name Pin No. I/O I/O Format Functions
LCTR
PH0/ADI0 PH1/ADI1 PH2/ADI2 PH3/ADI3
71
68 67 66 65
69
I
I
I
Universal counter (freqency and period measurement) / general­purose input port. This IOS instruction b3 with Pn=3 swithes the pin function between universal counter input and general-puropse input.
• Frequency measurement The universal counter function is selected by an IOS instruction with Pn=3 and b3=0. LCTR frequency measure­ ment mode is set up by a UCS instruction with b3=0 and b2=1, and counting is star ted with a UCC instruction after the count time is selected. The CNTEND flag is set when the count completes. To operate this circuit as an AC amplifier in this mode, the input must be capacitor coupled.
• Period measurement With the universal counter function selected, a UCS instruction with b3=1 and b2=0 sets up the period measurement mode and a UCC instruction starts counting after selecting the count time. The CNTEND flag is set when the count completes. In this mode, the signal must be input with DC coupling to tur n off the bias feedback resistor.
• For use as general-purpose input pin use. The general-pur pose input port function is selected by an IOS instruction with Pn=3 and b3=1. An internal register (address OEH) input instruction INR(b1) is used to acquire data from this pin. Input is disabled in clock stop mode. (The input pin will be pulled down.) During the power-on reset. The universal counter function(in HCTR frequency measurement mode) is selected.
HOLD
PLLcontrol and CLOCK STOP mode control pin. Setting this pin low in the hold enable state disables input to the FMIN and AMIN pins and sets the E0 pin to the high-impedance state. To enter clocl stop mode, set the HOLDEN flag, set this pin low, and execute a CKSTP instruction. To clear clock stop mode set this pin high. General-purpose input ports/ADC input pins. The IOS instruction with Pn=7 switches the pin function between genetal-purpose input ports and ADC inputs.
• For use as the general-purpose input port The IOS instruction with Pn=7 specifies the use as general­ pur pose input port in bit units.
• For use as ADC input pin The IOS instruction with Pn=7 specifies the use as ADC in bit units. The IOS instruction with Pn=1 specifies the pin to convert. The UCC instruction (b2) starts a conversion. The ADCE flag will be set when the conversion completes. Note) Executing an input instruction for a port specified for ADI use will always return low since input is disabled. These pins must be set up for general-purpose input port usage before an input instruction is excuted. (In other words, the port must be set to the general-porpose input function before the input instruction is executed.) Input is disabled in clock stop mode. During the power-on reset these pins go to the general-purpose input port function.
PJ0/DAC0 PJ1/DAC1 PJ2/DAC2 PJ3/DAC3
PK0/INT0 PK1/INT1 PK2 PK3
Vdd1 Vdd2
TEST1 TEST2
COM1 COM2 COM3
S1
|
S16
64 63 62 61
22 21 20 19
57 58 79
2
58 57 56
55
|
40
O
I/O
O
O
General-purpose output ports/DAC input pin. The IOS instruction with Pn=9 switches the pin function between general-purpose output ports and ADC inputs. Since these pins are open drain circuit, pull-up resistors are required in exrernal circuit accepting these outputs.
• For use as general-purpose output port The IOS instruction with Pn=9F specifies general-purrpose input por t use in bit units.
• For use as DAC The IOS instruction Pn=9 is used to switch the port in bit units. DA C data is loaded into tne DAC (0 to 3) specified with the DA C instruction, Although PWM waveform is output as soon as the por t is switched, the data prior to that load is output for up to 114µs (1/8.791kHz) after data is loaded. The general-purpose output port function is selected after a power
-on reset, and the output go to the transistor off (H output) state. General-purpose I/O / external interrupt ports
There is no instruction that switches the function between general­purpose ports and external interrupt ports. These pins function for input only when the external interrupt enable flag is set. (Output disables)
• For use as general-purpose I/O port These pins can be set for input or output in bit units (bit I/O). The IOS instruction is used to specify input or output in bit units.
• For use as external interrupt pin This function can be used by setting the external interrupt enable flags (INT0EN and INT1EN) in status register 2. The corresponding pin is automatically set to the input por t. To enable interrupt operation, the interrupt enable flag (INTEN) in status register 1 must also be set. The IOS instruction with Pn=3, b1=INT1, and b0=INT0 is used to select rising or falling edge detection. In clock stop mode, input is disabled and these pins go to the high­impedance state. During the power-on reset, these pins go to the general-purpose input port function.
Nch
open drain
CMOS
push-pull
CMOS
three value
output
CMOS
three value
output
Pin for external application of 2/3 voltage of LCD drive bias. Pin for external application of 1/3 voltage of LCD drive bias. LSI test pin.
These pins must be either left open or connected to ground. LCD driver common output pin.
Driver format 1/3 duty, 1/3 bias. This pin is fixed at the low level in CLOCK STOP mode. This pin is fixed at the low level after a power-on reset.
LCD driver common output pin. Driver format 1/3 duty, 1/3 bias. The frame frequency 100MHz. This pin is fixed at the low level in CLOCK STOP mode. This pin is fixed at the low level after a power-on reset.
Page 14
- 13 -
IC BLOCK DIAGRAM & DESCRIPTION
IC601 IC LC72338-9C41-E (Single-Chip PLL + Controller)
Pin name Pin No. I/O I/O Format Functions
S21/PF0 S22/PF1/SCK1 S23/PF2/SO1 S24/PF3/SI1
S29/PN0/BEEP S30/PN1 S31/PN2 S32/PN3
35 34 33 32
26 25 24 23
I/O
O
LCD driver segment output, general-porpose input/output and serial I/O ports. The PF0 to 3 inputs are in the Schmidt format. The IOS instruction is used to switch between the LCD driver segment output, general-purpose I/O, and serial I/O functions, and to switch between input and output of the general-purpose input port function.
• For use as segment output These pins can be set in 4 bits units. The IOS instruction with Pn=OEH specifies segment output use in bit units. b0=S21 to 24/ PF0 to 3 0 • • • Segment output 1 • • • PE0 to 3
• For use as general-purpose input /output port These pins can be set to input /output in bit units. (1 bit I/O) b1=SI/O 1 0 • • • Genetal-purpose port 1 • • • SI/O port Input /output is specified with the IOS instruction in bit units. PF • • • Pn=5 0 • • • Input 1 • • • Output
• For use as serial I/O port The serial I/O por t function is specified with the IOS instruction (Pn=0). The contents of the serial I/O data buffer can be saved and loaded with the INR and OUTR instructions. *Pin setup states when used as a serial I/O port PF0 • • • General-purpose input /output PF1 • • • SCK1 output in internal clock mode SCK1 output in external clock mode PF2 • • • SO1 output PF3 • • • SI1 input In CLOCK STOP mode, if this port is used as a general-purpose I/O port or as a serial I/O port, the pins go to the input disabled high-impedance state. If used for segment output, the pins are fixed at the low level. The segment output port function is selected after a power-on reset.
Segment output/general-porpose input port 1/ BEEP tone output pins. The IOS instruction is used to switch between the segment output port and the PN0 to 3 functions. The BEEP instruction switches between the general-purpose output port and BEEP tone function.
• For use as segment output These pins can be set in 3 bits units. The IOS instruction with Pn=OEH specifies segment output use in bit units. b2=S29 to 32/ PN0 to 3 0 • • • Segment output 1 • • • PN0 to 3
• For use as general-purpose output. The general-porpose output port function is selected with the BEEP instruction (b3=0). PN1 to 3 are dedicated general-purpose output function pins.
• For use as BEEP output pin The BEEP instruction with b3=1 sets the BEEP output. The BEEP instruction bit b0,b1 and b2 sets the frequency. When this is set as the BEEP port, executing an output instruction will rewrite the inter nal latch data but has no influence on the output. These pins go to the output high-impedance state in clock stop mode. If used for segment output, the pins are fixed at the low level. These pins go to the output high-impedance state during the power-on reset and hold that state until an output instruction is executed.
CMOS
three value
output
and
push-pull
CMOS
three value
output
and
push-pull
Pin name Pin No. I/O I/O Format Functions
S17/PE0 S18/PE1/SCK2 S19/PE2/SO2 S20/PE3/SI2
S25/PM0 S26/PM1 S27/PM2 S28/PM3
39 38 37 36
30 29 28 27
I/O
I/O
LCD driver segment output, general-porpose input/output and serial I/O ports The IOS instruction is used to switch between the LCD driver segment output, general-purpose I/O, and serial I/O functions, and to switch between input and output of the general-purpose input port function.
• For use as segment output These pins can be set in bit units. The IOS instruction with Pn=ODH specifies segment output use in bit units. b0=S17/PE0 0 • • • Segment output b1=S18/PE1 1 • • • PE0 to 3 output b2=S19/PE2 b3=S20/PE3
• For use as general-purpose input /output port These pins can be set for input /output in bit units. (1 bit I/O) b2=SI/O2 0 • • • Genetal-purpose port 1 • • • SI/O por t Input /output is specified with the IOS instruction in bit units. PE • • • Pn=4 0 • • • Input 1 • • • Output
• For serial I/O port The serial I/O port function is specified with the IOS instruction (Pn=0). The contents of the serial I/O data buffer can be saved and loaded with the INR and OUTR instructions. *Pin setup states when used as a serial I/O port PE0 • • • General-purpose input /output PE1 • • • SCK2 output in internal clock mode SCK2 output in external clock mode PE2 • • • SO2 output PE3 • • • SI2 input In CLOCK STOP mode, if this port is used as a general-purpose I/O port or as a serial I/O port, the pins go to the input disabled high-impedance state. If used for segment output, the pins fixed at the low level. The segment output port function is selected after a power-on reset. LCD driver segment output, general-porpose input /output ports. The IOS instruction is used to switch between the LCD driver segment output, general-purpose I/O port, and serial I/O to switch between input and output of the general-purpose input /output port function.
• For use as segment output These pins can be set in 4 bits units. The IOS instruction with Pn=OEH specifies segment output use in bit units. b0=S25 to 28/PM0 to 3 0 • • • Segment output 1 • • • PM0 to 3
• For use as general-purpose input /output port These pins can be set for input /output in bit units. Input /output is specified with the IOS instruction in bit units. PM • • • Pn=OCH 0 • • • Input 1 • • • Output In CLOCK STOP mode, if this port is used as a general-purpose I/O port, the pins go to the input disabled high-impedance state. If used for segment output, the pins are fixed at the low level. The segment output port function is selected after a power-on reset.
CMOS
three
value
output
and
push-pull
CMOS
three
value
output
and
push-pull
XIN
TEST2
SI0/PG3
SO0/PG2
SCK0/PG1
PG0
PC3
PC2
PC1
PC0
PB3
PB2
PB1
PB0
PA 3
PA 2
PA 1
PA 0
PK3
PK2
INT1/PK1
INT0/PK0
PN3/S32
PN2/S31
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
PJ0/DAC0
PJ1/DAC1
PJ2/DAC2
PJ3/DAC3
Vdd1
Vdd2
COM1
COM2
COM3
S1
S2
S3
S4
S5
S6
S7
S8
S9
S10
S11
S12
S13
S14
S15
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65
PN1/S30
BEEP/PN0/S29
PM3/S28 PM2/S27 PM1/S26 PM0/S25 [Vpp]Vdd
SI1/PF3/S24
SO1/PF2/S23
SCK1/PF1/S22
PF0/S21
SI2/PE3/S20
SO2/PE2/S19
SCK2/PE1/S18
PE0/S17
S16
XOUT TEST1 E02 E01 VSS AMIN FMIN Vdd SNS LCTR HCTR HOLD PH0/ADI0 PH1/ADI1 PH2/ADI2 PH3/ADI3
Page 15
- 14 -
LCD DISPLAY DESCRIPTION
PAD NO.
1 2 3 4 5 6 7 8
9 10 11 12 13 14
IC NO.
C1 C2 C3 S1 S2 S3 S4 S5 S6 S7 S8
S9 S10 S11
COM1
COM1
--
-­7A 7B
ON
6A 6B
OFF
T1
5 T5 4A 4B
COM2
--
COM2
-­7F 7G 7C 6F 6G 6C
MHz
PROG.
T6 4F 4G
COM3
--
--
COM3
7E 7D CH 6E 6D TR
kHz
BASS
ST 4E 4D
PAD NO.
15 16 17 18 19 20 21 22 23 24 25 26 27 28
IC NO.
S12 S13 S14 S15 S16 S17 S18 S19 S20 S21 S22 S23 S24 S25
COM1
4M 3A 3B 3M
T2 T9
T8 2A 2B
2h 1A 1B
1h
SURR
COM2
4C 3F 3G 3C T4 T3 4h 2F 2G 2C 1F 1G 1C
SLEEP
COM3
4K 3E 3D 3K
T7
--
3h 2E 2D
MONO
1E 1D 1K AM
1
A
G
K
KK
MM
BF
D
CE
1
1h
3h 4h
2h
T1
T9
T2
T4 T6 T7
T3 T5
T8
23 45 6
7
28
LCD60
IC BLOCK DIAGRAM & DESCRIPTION
28 27 26 25 24 23 22 21 20 19 18 17 16 15
1234567 891011121314
Vcc
Vcc
DRIVER MUTE
D.B UFD.BU FD.B UFD.BU F
D.B UFD.BU FD.B UFD.BU F
Level shift
Level shift
Level shift
Level shift
T.S . D
IC103 MM1469XH (CD Driver)
Page 16
- 15 -
This is a basic wiring connection.
WIRING CONNECTION
L-CH
SPEAKER
BOX
R-CH
SPEAKER
BOX
POWER
TRANSFORMER
P. W.B
KEY P.W.B
CD P.W.B
FRONT P.W.B
CN602(16P)
LCD60
CN601(14P)
CN202
(16P)
CN204
(2P)
CN604
(2P)
CN201
CN122
(8P)
CN111
(16P)
(16P)
CN113
(6P)
(6P)
CN441
(2P)
CN490
(8P)
CN491
(14P)
CN421
PHONES
CN402
(2P)
CN401
(2P)
CN406
(4P)
CN405
(4P)
FU401
T2.5A L 250V
AMPLIFIER P.W.B
TUNER P.W.B
AM LOOP ANT.
CN455
(2P)
P. T
AC IN
CN452
(BL)
CN451
(BW)
MOTOR
SWITCH
R/P HEAD
RED
ORANGE
YELLOW
BROWN
M
TAPE DECK MECHANISM
CN203
(1P)
FM
ANT.
Page 17
- 17 -- 16 -
This is a basic schematic diagram.
SCHEMATIC DIAGRAM (FRONT)
NC.
QSOUND
POWER-RY
BEAT ST_BY +5.6V
GND
AC_SENS
TAPE_PLAY
VOL_DATA
A_MUTE
VF-CE
SYNC_REC.
VOL_CLK
STEREO
SD
AMIF
MONO
LID.SW
BAND1
VT
BAND2
GND
TU_MUTE
AMOSC
KEY2
TU_+B
TU_L
TU_GND
TU_R
R6009
R6114
IC601
R6106
R6105
C6103
C6101
C6100
R6201
C6201
Q6201
Q6200
R6109
R6108
R6107
D6901
C6903
C6900
C6901
R6104
R6111
R6112
R6113
C6200
X6001
C6104
C6105
L6900
C6102
C6205
C6204
C6206
S6500
R6501
R6502
C6501
C6502
R6008R6014 R6013
S6009
S6008
R6007
S6007
S6010
D6902
R6905
C6905
R6012
R6011
R6010
C6012
C6011
C6010
C6202
C6203
C6208
C6912
C6911
C6910
C6913
C6915
C6914
C6918
R6907
S6011
S6012
R6015R6016
R6200
L6901
C6904
R6003R6005 R6004
S6005
S6004
R6002
S6003
S6002
S6001
C6920
C6922
LCD60
S6006
R6001
S6013
C6916
R6951
R6952
D6951
D6952
R6954
R6953
R6906
SE601
CN601
R6908
CN602
33K
47K
LC72338-9C41-E
10K
10K
330P
330P
330P
2.7K
0.01
2SC1740
2SC1740
47K
4.7K
4.7K
1SS133
0.01
10/16
0.01
10K
47K
10K
10K
1/50
4.5MHz
56P
56P
10
100P
100P
100P
100P
JOG
1K
1K
0.01
0.01
6801.2K 820
TU/DOWN
CD STOP
560
CD PLAY
TU/UP
1SS133
100
1000/6.3
10K
10K
10K
100P
100P
100P
1000P
100P
2200P
0.01
0.01
0.01
100P
100P
100P
2200P
47K
POWER
FUNCTION
1.5K2.2K
2.2K
22UH
47/10
8201.5K 1.2K
BASS
SURR.
680
CLOCK TIME
PRESET/PRE.
TU/BAND
100P
0.01
SOUND PRESET
560
MEMORY
1000P
560
560
000
000
560
560
470
10K
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
123
54
12345678910111213141516171819202122232425262728
-2-1
KEY2 GND
CN604
123
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
4
5
6
25
2930323334
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
585756555450515253
4944484746
45
404142433935343332
63
64
26
30
35
TU_+B
TU_L
CD_RESET
62
27
8
9
29
3
10
14
TA_PLAY
21
28
373836
71
66
65
4
5
3
8
14
38
25
62
63
TA_PLAY
65
66
21
28
27
9
10
75
26
23
71
36
TU_+B
TU_GND
13
64
13
37
TU_GND
23
24
24
TU_R
17
TU_L
KEY2
KEY2
75
TU_R
18
18
6
CD_RESET
17
TEST2
CQCK
RWC
DSP_RESET
BAND1
AUX_MUTE
BEAT
IR
BAND2
STEREO
SD
S18
S17
S20
S21
VDD
S22
S23
S24
S25
A
MUTE
SYNC_REC.
S11
S10
S9
S8
S7
S6
S5
S4
S2
S1
COM3
COM2
COM1
(VDD2)
(VDD1)
VF_CE
D_OUT
D_CLK
KY1
DIST
SELECTION
VDD
AMOSC
FMOSC
VSS
EO2
TEST1
XIN
S15
MONO
S19
SQOUT
S14
S13
S12
COIN
PICK_SW.
TU_MUTE
BASS
JOG2
WRQ
TAPE_PLAY
POWER RY
P_CON
DEMO. SELECT
SURR
DRF
S16
AC_SENS
FMIF
AMIF
LID_SW.
EO1
S3
XOUT
(POWER)
JOG1
KY0
EU-1 US JP
SS EU-2 JP
OPEN 0 8.2K
TO TUNER SEC.
DRF
COIN CQCK RWC CD_RESET WRQ
TO CD SEC.
TO AMP SEC.
8.2K 10K 10K
8.2K 8.2K 10K
15K 15K 27K
SQOUT
TU_+B TU_R TU_GND
TO FMOSC
(PICK_SW.)LIMIT
R6115
MODEL JPOOTHER
CLOCK
AUX
CLOCK
(TV)
8.2K
[H:ON/L:OFF]
[H:ON/L:OFF]
[LCD LIGHT]
[FRONT LIGHT]
TU_L
R6009
UMBER
UMBER
TO KEY SEC.
Page 18
- 19 -- 18 -
REF
REF
FSS
CLK
TBC
FSC
CLK
REF
REF
8CM
12CM
FOADJ
FSTA
STOP
REF
GEN
FSTA
VR+0.3V
REF
FSS
FSC
TOFF
REF
REF
REF
STOP
TOSTA
TOADJ
GEN
TBC
LATCH
PONRST
DAT
CL
CE
SLOF
8/12CM
FSTA
LASER
2FREQ
TOSTA
FOSTA
EFBAL
JP-
JP+
TGL
TOFF
TES
HFL
SLOF
CV-
CV+
RF
REF
REF
FOCS
THLD
DEF
CL
DAT
CE
DRF
S.DVCC
VCC
REF
DRF
HFL
VDRF
VHFL
DEF
GAIN
VCA
PH4
BH2
PH1
BH1
RF
LASER
VPPC
RFVCC
FE1
REF
VCA
REF
REF
REF
REF
VCA
BAL
BAL
REF
BPL
VCA
VCC
Q
R
a
D
S.Q.R
SLOFSLOF
SLOF
TO
REF
REF
SPOF
REF
JP+
JP
JP-
CV+
CV-
REF
REF
FE1
REF
FOFF
REF
FSTA
FSERCH
REF
REF
JP
TOFF2
REF
TGHI TGLI
THLDI
THLDI
TGLI
TGHI
OR
GEN
WCOMP
THLD
DEF
TGL
THLDI
TGLI
OR
AND
REF
TES
SHOCK:WCOMP
-HIST.COMP
TU_GND
TU_R TU_L CD_R
CD_GND
CD_L
GND
+B
C1476
X1451
C1313
C1480
R1503
R1502
R1501
R1337
C1333
R1473
R1472
C1470
C1481
C1491
C1457
C1335
C1472
R1332
C1346
C1492
C1493
R1456
C1456
C1452
R1455
C1451
R1454
C1341
R1475
C1475
R1343
IC101
C1339
C1337
C1338
C1336
C1319
R1329
C1320
R1328
C1317
R1326 R1325
C1318
R1324
C1316
C1315
R1318
R1320
R1317
R1315
R1313
C1312
R1314
C1310
R1310
R1311
C1305
R1304
R1336
R1453
C1331
R1335
L1451
C1468
C1467
C1469
R1464
R1465
R1463
R1462
C1329
C1471
R1308
C1330
R1312
IC102
C1332
C1325
C1301
R1301
R1302
C1309
R1309
C1302
R1305
C1304
R1303
C1323
R1333 R1334
C1334
C1321
R1331
R1330
C1324
C1783
R1327
C1773
C1772C1782
R1783 R1773
R1781
R1771
C1350
D1404
Q1301
C1322
IC103
CN113
C1403
C1401
Q1401
PR140
CN111
R1340
R1342
R1344
R1345
C1402
C1404
C1408
C1407
R1346
R1347
CN122
D1410
R1480
R1476
C1405
C1308
C1495
C1485
C1303
C1455
R1498
C1415
R1499
C1340
D1401 D1402 D1403
R1338
C1478
C1477
C1784
0.022
16.93M
0.1
0.022
1.5K
3.3K
3.9K
6.8K
0.22;50
100K
4.7K
68P
100P
0.01
10;25
10;50
0.01
18K
33P
47;10
0.01
10K
0.01
0.1
18K
0.1
680
3300P
560
68P
100K
LA9242M
10;25
0.01
10;25
0.01
4.7;50
6.8K
22;50
6.8K
0.22;50
1K 56K
100P
33K
3300P
0.018
1.5K
8.2K
68K
15K
22K
1000P
22K
0.15
15K
100K
330P
6.8K
330
2.7K
0.01
10K
10;K
68P
68P
100P
1K
560
560
560
4.7;50
68P
27K
10;25
6.8K
LC78629E
0.047
2200P
47;10
100
10
0.047
330
1000P
2.2K
0.033
150K
12P
15K 1K
0.01
3300P
220K
220K
0.033
10;25
56K
10;25
1000P1000P
100K 100K
1K
1K
0.018
MTZJ5.1B
2SB810
1P
MM1469XH
470;10
470;6.3
KTA1273
400mA
82K
82K
82K
82K
0.01
0.01
100;16
0.022
150K
150K
RL153
560
1K
0.01
0.22
0.01
0.01
0.22
0.1
100
220P
100
0.1
1SS133 1SS133 1SS133
330K
100P
0.022
100P
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
32313029282726252423222120191817
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
48474645444342414039383736353433
16 15 14 13 12 11 10 987654321
49505152535455565758596061626364
32313029282726252423222120191817
28 27 26 25 24 23 22 21 20 19 18 17 16 15
1413121110987654321
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
CD_L
CD_R
DRF
WRQ
RWC
SQOUT
COIN
CQCK
A.GND
REST
COIN
SQOUT
CQCK
WRQ
CD_L
CD_R
TU_L
TU_R
TU_GND
A.GND
RWC
DRF
TU_+B
TU_GND
TU_R
TU_L
TU_+B
REST
(SLED +)
(SLED -)
(D-MUTE)
FSX
CONT2
CONT1
TEST2
DVSS
TB
F
E
FIN1
FIN2
FSS
VCC1
LDS
LDD
BH1
PH1
LF2
VR
REFI
VCC2
DRF
CE
DATCLCLK
DEF
NC
TBC
FSC
DGND
SLI
SLC
RFS-
RFSM
CV+
CV-
SLOF
TES
HFL
TOFF
TGL
JP+
JP-
SL+
SL-
SLD
SLEQ
SPD
SP-
SPG
SPI
SP
AGND
FE-FEFA-FAFD-
FD
TO
JP
TD
TD-
TA
TH
SCH
TESI
TE
TE-
VVSS
PDO
ISET
TAI
DEFI
REST
XOUT
XIN
TEST5
TST11
4.2M
16M
CS
TEST1
CQCK
COIN
SQOUT
RWC
WRQ
PW
SBCK
SFSY
XVSS
EFLG
SBSY
XVDD
MUTER
RVDD
RCHO
RVSS
LVSS
LCHO
LVDD
MUTEL
NC
TEST4
TEST3
DOUT
C2F
EMPH
CONT5
CONT4
JP-
JP+
DVDD
CONT3
TGL
TOFF
FSEQ
PCK
TES
HFL
V/P
CLV-
CLV+
FR
EFMIN
EFMO
VVDD
VC
TE
FE
RF
TO FRONT PWB
BASE
MECHANISM
TU_R
RESET
TU_GND TU_+B
WRQ
DRF
LIM_SW
COIN SQOUT
CQCK
RWC
TU_L
5V
REG
VC
VDD
VDD
MUTEININ
IN IN
++
+---
-
+
D
C
B
A
LIMIT
GND
F-
T-
T+
F+
E
VR
SL+
SP+
SL-
GND
MD
SP-
F
LD
D
A
B
C
LD
MD
GND
MD
LD
VR
T+
F+
F-
T-
F
E
LIMIT SW
SPINDLE MOTOR
SLED MOTOR
PICK UP
DT11T3CN
COMMON
SHORT
LAND
TRCKING
COIL
FOCUS
COIL
M
M
SVR
COM
SP+
SP-
SL+
SL-
LIMIT
GND
VREFVREF
+9V
4.3
4.9
3.6
1.6
3.6
4.2
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
0.0
0.0
2.2
2.5
2.2
2.5
2.5
2.5
2.5
2.5
2.9
2.5
2.5
2.5
2.5
2.5
2.3
2.3
2.3
2.3
0.0
0.0
0.0
0.0
4.8
4.8
0.0
4.8
0.0
4.8
2.4
1.6
2.4
2.4
0.0
0.0
2.5
2.5
2.5
2.5
0.0
0.0
4.9
4.9
0.2
0.0
3.6
4.2
2.2
2.2
2.5
1.0
2.5
1.0
2.5
2.5
2.5
2.5
4.9
4.9
0.0
0.0
4.8
0.0
0.0
0.0
0.0
0.0
1.5
1.5
4.8
4.8
0.0
0.0
2.3
2.3
0.0
0.0
0.0
4.8
0.0
4.8
4.8
4.8
0.0
0.0
0.0
0.0
4.8
4.8
4.8
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
4.7
5.1
5.1
2.1
2.1
0.0
0.0
2.1
2.1
5.1
5.1
0.0
4.7
4.8
4.8
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
4.8
4.8
5.0
5.0
8.0
8.2
8.0
8.4
PLAY
STOP
SCHEMATIC DIAGRAM (CD)
This is a basic schematic diagram.
Page 19
- 21 -- 20 -
FRONT P.W. BOARD
WIRING DIAGRAM ( FRONT & CD )
15 10 15 20 25
E
E
E
E
E
DIP
DIP
S6008
S6009
S6010
S6007
IC601
SE601
S6002 S6001
S6013 S6012 S6011
LCD60
Q6201
Q6200
C6900
J6202
J6300
J6211
J6301
J6302
R6907
L6901
J6307
J6205
J6206
J6309
J6213
J6207
J6208 J6209
J6311
J6103
D6901
C6904
J6305
D6902
J6106
J6314
D6951
J6204
D6952
R6200
J6218
J6220
J6219
TU_GND
TU_L
TU_+B
KEY2
AMOSC
TU_MUTE
VT
BAND2
GND
BAND1
LID.SW
MONO
AMIF
SD
STEREO
TU_R
VOL_CLK
SYNC_REC
VF_CE
A_MUTE
VOL_DATA
TAPE_PLAY
AC_SENS
GND
+5.6V
ST_BY
BEAT
POWER_RY
SURR
CN601
TU_L
TU_GND
TU_R
TU_+B
SQOUT
COIN
RWC
CD_RESET
COCK
WRQ
DRF
PICK_SW
S6500
TU/BAND
POWERFUNCTIONMEMORY
TU/UP
TU/DOWN
CD PLAY
CD STOP
PRESET
L6900
C6103
J6316
X6001
C6200
J6221
J6304
C6905
J6212
J6210
J6312
J6303
J6310
J6313
J6203
J6201
J6200
C6912
J6411
J6400 J6401 J6402 J6403 J6404 J6405 J6406 J6407 J6408 J6409 J6410
J6306
1AD4B10D2411B
T002A 94V-0
J6308
CN601
CN602
J6215
J6216
J6214
J6104
J6217
J6105
J6101
CN602
J6315
J6102
J6100
C1401
A
MD
SVR
LD
GND
T­T+
F+
F-
T002A 94V-0
C1330
C1317
C1319
C1320
C1335
CQCK
COIN
SQOUT
RWC
WRQ DRF
L1451
IC103
C
D
F
B
GND
LIMIT
SL+ SL-
SP+ SP-
J1208
J1106
Q1301
J1305
J1200
C1403
J1301
C1338
J1210
J1309
J1307
C1339
Q1401
C1301
C1333
J1214
J1112
J1204
J1303
J1203
J1202
J1201
REST
J1213
D1404
TU+B
TUGND
TU_L
TU_R
J1121
J1110
J1205
CN113
J1321
PR140
C1329
CN122
J1101
J1209
400
CN111
J1311
J1313
C1773
1AD4B10D2410C
J1111
J1315
J1316
J1211
J1314
J1312
J1115
J1310
J1109
C1408
J1118
J1319
J1320
COMMON
VREF
J1302
J1102
LIM SW
J1308
D1401
D1402
D1403
J1119
J1317
J1318
C1457
J1206
J1300
J1212
J1104
J1306
J1108
C1783
J1100
J1207
C1476 C1478
D1410
J1120
J1304
J1322
J1114
J1117
J1113
J1116
C1492
J1107
IC102
IC101
J1103
X1451
J1105
J1215
R6201
R6201
R6112
R6112
C6910
C6910
C6501
C6501
C6203
C6203
C1772
C1772
C1782
C1782
C1475
C1475
C1404
C1404
R1773
R1773
R1465
R1465
R6201
C6201
C6903
R6905
C6901
C6901
C6204
C6204
R6104
R6104
R6015
R6015
R6016
R6016
C6922
C6922
C6916
C6916
C6208
C6208
R6908
R6908
R1318
R1318
C1318
C1318
R1329
R1329
C1302
C1302
R1302
R1302
C1324
C1324
C6901
C6204
R6104
C6206
C6102
C6100
C6101
C6911
R6109
R6002
C6914
C6915
C6913
C6918
R6906
C6920
C6205
R6112
C6910
R6001
R6008
R6106
R6105
C6501
C6502
R6502
R6501
R6952
R6951
R6953
R6954
R6014
R6014
C6105
C6105
C6104
C6104
R6013
R6013
R1301
R1301
C1407
C1407
C1337
C1337
R6014
R6015
R6016
C6203
C6202
R6107
R6108
R6111
C6922
C6010C6011C6012
R6010R6011R6012
C6916
C6208
C6105 C6104
R6113
R6013
R6007
R6908
R6114
R6009
R1343
C1325
R1332
R1333
C1323 R1334
R1336
R1335
C1303
R1305
R1304
R1303
C1309
C1308
C1305
C1304
R1308
R1309
R1310
R1311
C1310
R1312
R1313 C1312
R1315
R1318
R1320
CAN1
R1324
C1318
R1328
R1325
R1327
R1326
R1329
R1453
R1301
C1315
C1316
R1314
C1302R1302
C1341
C1322
C1324
R1456
C1452
C1456
R1455
C1451
C1471
C1772
C1782
R1781
C1346
C1493
C1472
R1783
C1481
R1331 R1330
R1472
R1337
C1336
R1463
C1475
C1470
R1464
C1469
C1468
C1467
R1475
R1503
R1502
R1501
R1473
C1340
C1402
C1313
C1332
R1480
C1404
R1499
C1455
C1485
C1495
C1415
R1454
C1350
R1317
C1321
R1773
R1771
R1462
C1331
R1476
C1405
R1465
C1491
R1347
R1344 R1345 R1340 R1342 R1346
C1407
R1338
C1337
C1480
C1334
C1477
R1498
C1784
This is a basic wiring diagram.
CD P.W. BOARD
Page 20
- 23 -- 22 -
TO CN490 CD GND
TU_EARTH
STEREO
SD
AMIF
MONO
LID_SW
BAND1
VT
BAND2
GND
TU_MUTE
AMOSC
KEY2
TU_+B
TU_L
TU_GND
TU_R
GND
KEY2
IC201
C2005
C2002
C2008
R2003
R2014
C2017
C2003
L2002
L2003
R2001
C2001
R2005
R2002
C2015
C2011
C2012
C2014
C2013
C2009
XF211
XF212
R2113
CT211
C2102
C2103
Q2101
R2101
C2101
C2104
R2104
R2106
C2108
C2106
C2107
C2110
IC211
L2205R2117
Q2201
R2119
R2201
C2209
R2107
C2122
C2120
C2118
C2117
C2702
C2802
C2121
C2119
D2101
C2801
C2701
R2205
Q2102
R2206
C2218
R2701
C2019
C2140
C2021
C2141
Q2110
R2004
R2801
L2204
C2311
Q2111
R2128
R2127
C2207
R2210
D2003
D2002
D2102
C2025
Q2001
R2007
R2009
C2020
R2008
C2027
L2005
L2007
CN201
D2004
D2005
R2006
C2312
L2006
R2105
T2001
S2001-1
R2126
CN203
C2026
C2113
C2115
C2114
R2301
R2302
C2111 R2303
C2112
C2010
TO FRONT GND
T2002
C2022
C2029
D2006
XF215
L2001
FMOSC
R2901
XF210
C2126
C2142
R2131
C2131
Q2002
R2011
R2010
D2104
Q2003
R2129
C2902
R2900
C2024
D2105
CN202
CN204
R2910
LA1186N
0.01
0.022
15P
18
100K
1000P
3P
8.2UH
330K
0.01
22
10K
0.022
15P
5P
0.01
0.022
0.47/50
10K
0.01
0.01
KRA107M
3.9K
0.01 10/25
10K
2.7K
100/10
0.47/50
1/50
0.047
LA1844ML
820K
KRA107M
27K
100
1000P
18K
0.022
0.022
0.033
680P
0.022
0.022
4.7/50
22/25
1SS133
2.2/50
2.2/50
68K
KRC107M
2.2K
100/10
15K
0.022
0.1
1000P
1P
KRC107M
10K
15K
0.022
KTC3195
330K
4.7K
0.022
1.0K
SVC211-B--C
SVC211-B--C
SVC342
1000P
KTC3195-O
560K
330
0.022
220
100P
22UH
22UH
AM ANT TERMANL
1SS133
1SS133
560
10/25
22UH
10K
120K
1000P
1/50
4700P
0.1
68K
22K
10/25 18K
4.7/50
100P
10.7MHZ
1P
0.01
1SS133
450KHz
1K
0.047
22P
56K
560P
KTC3195-O
120K
100
MTZ5.6B
KTC3199-GR
22K
47P
000
0.1
1SS133
000
123456789
121110987654321
24 23 22 21 20 19 18 17 16 15 14 13
123
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
2
1
(E)
(CH)
(CH)
(MW)
(MW)
TP202
TP201
(CH)
TP203
FM 75 OHM
AM LOOP
S2001-2
TO FRONT CN603
2P-9P
(H)
(CH)
0.95 1.63 4.66 0 0 4.66 0 3.98 4.66
0 0
3.56 0
0
4.82
2.11
2.11
4.75
4.9
2.11
2.11
2.09
2.1000
4.84
4.84
4.83
4.84
2.70
3.38
4.75
4.9000
3.57
1.55
3.57 0
3.71
3.55
1.12
1.13
1.16
1.17
2.1
2.1
2.16
0.18
2.75
1.5302.26
1.26
1.53
2.06
2.09
2.07
2.10
4.75
4.90
3.30
3.45
4.70
4.87
4.74
4.90
0 0
00.0
00.0
00.0
00.0
00.0
00.0
FM AM
0
4.5
0.7
R OUT L OUT
0.7
0.8
0
SCHEMATIC DIAGRAM (TUNER)
This is a basic schematic diagram.
Page 21
- 25 -- 24 -
WIRING DIAGRAM (TUNER)
This is a basic wiring diagram.
E
MW ANT
E
E
E
T002A 94V-0
E
E
E
E
VT
L2205
XF212
IC201
XF211
CT211
Q2001
D2005
D2004
D2102
SH201
D2002
D2003
C2009
J2126
L2003
J2210
C2104
J2209
C2111
C2119
C2121
C2801
C2701
C2106
C2113
C2107
D2101
L2005
Q2101
L2006
J2203
J2206
J2119
C2312
C2108
Q2111
J2308
C2218
Q2201
J2115
J2205
S2001
J2208
CN201
L2002
1AD4B10D2411D
J2305
J2116
J2117
C2112
T2002
T2001
J2124
U
J2121
L2204
J2307
L2007
Q2002
D2104
CN203
Q2102
J2301
Q2110
J2202
XF215
J2302
R2129
CN202
J2118
J2111
J2125
J2113
J2303
J2120
J2304
J2306
CN204
XF210
J2114
D2105
J2123
Q2003
J2122
J2204
J2207
J2201
J2112
J2127
D2006
L2001
IC211
C2131
C2142
R2131
C2024C2005
C2002
R2001
C2001
C2001
C2014
C2014
C2022
C2022
C2001
R2002
C2014
R2005
C2013
R2004
R2003
C2011
C2011
C2015
C2015
R2008
R2008
C2117
C2117
C2122
C2122
C2702
C2702
R2801
R2801
R2701
R2701
C2115
C2115
R2301
R2301
C2114
C2114
R2303
R2303
R2302
R2302
C2120
C2120
C2011
C2012
C2008
C2015
R2014
C2017
C2003
C2003
C2101
C2101
C2802
C2802
C2209
C2209
C2311
C2311
C2003
R2006
R2008
R2007
R2009
C2021
R2101
C2101
C2118
C2117
C2122
C2702
C2802
R2801
R2701
C2103
C2103
R2106
R2106
R2126
R2126
R2910
R2910
C2902
C2902
C2103 C2102
R2104
R2106
C2110
C2126
R2113
R2113
R2900
R2900
R2113
R2117
R2119
C2209
C2020
C2019
C2311
C2207
R2128
R2127
R2206
R2201
C2027
C2140
C2025
R2126
C2026
C2115
R2301
C2114
R2303
R2302
R2105
C2010
R2205
C2022
C2029
R2901
R2010
R2011
R2210
R2107
R2910
C2141
R2900
C2902
C2120
Page 22
- 27 -- 26 -
TU_GND TU_RCH TU_LCH CD_RCH A_GND CD_LCH CD_GND CD_+B
VOL_CLK
SYNC_REC.
VOL_STB
A_MUTE
VOL_DATA
TAPE_PLAY
AC_SENS
GND
+5.6V
ST_BY
BEAT
POWER_RY
QSOUND
NC.
(TO CN411)
R4911
Q4902
C4920
R4910
C4919
R4912
C4921
C4918
IC412
R4718
C4713
C4911
R4818
C4813
C4815
C4714
C4715
C4814
C4716
C4913
R4781
C4912
C4816
R4881
C4712
C4812
C4905
C4909
R4905
CN406
L4902
R4941
CN405
Q4951
D4951
R4951
C4952
C4951
R4952
R4752
R4852
C4953
PR495
C4916
Q4751
Q4851
R4756
R4856
R4961
D4963
D4962
R4962
C4751
C4851
C4961
R4717
R4817
R4816
R4716
Q4904
C4906
CN421
R4938
C4811
C4711
C4726
C4826
Q4106
R4106
R4704
R4703
R4803
R4804
C4704
C4804
C4703
C4803
R4901
C4901
C4802
C4702
C4807
C4707
R4710
R4810
C4805
C4705
R4805
R4705
C4806
C4706
R4708
C4708
C4709
R4709
C4808
R4808
R4809
C4809
CN401
CN402
S4950
IC410
Q4103
Q4903
D4102
Q4104
R4107
PR496
D4953
C4962C4963
R4991
CN490
C4984
Q4840
Q4740
R4857
R4859
R4858
R4757
R4759
R4758
R4914
C4110
R4110
R4108
Q4108
C4750
C4850
Q4992
Q4994
R4953
C4915
IC446
D4993
C4994
C4997
R4104
R4105
C4993
Q4995
R4955
R4954
L4780
L4781
L4881
R4860
R4760
C4801
C4701
R4761
R4861
C4731
C4923
C4922
R4923
R4922
C4924
R4924
IC411
C4730
R4963
R4825
R4731
R4725
R4722
R4721
R4728
R4727
R4822
R4821
R4831
R4828
R4827
R4820
R4826
R4726
R4720
R4832R4732
C4828
C4827
C4728
C4727
C4829
C4729
C4725 C4825
C4733
C4722
C4721
C4720
C4833
C4822
C4821
C4820
D4961
CN491
R4762
R4862
L4591
CN452
CN451
CN455
230V 50Hz
CN411
C4980 C4981
D4980
D4981
D4983
D4982
C4982
C4983
12
2SC3330
0.01
10K
0.01
330
10/25
1000P
TA8229K
TA8229K
560
47/10
330/10
560
47/10
100/16
0.15
100/16
0.15
1000/16
3300/25
150
220/25
1000/16
150
3300P
3300P
10/25
220/10
100
27
KTD2058
MTZJ9.1B
470
0.022
47/25
470
2.2
2.2
470/16
1250mA
180P
2SD1012
2SD1012
4.7K
4.7K
10K
1SS133
1SS133
1K
1/50
1/50
1;50
15K
15K
1K
1K
2SC3330
1000P
10K
10/25
10/25
1/50
1/50
KRC102M
10K
3.9K
68
68
3.9K
47/10
47/10
0.022
0.022
390K
47/10
1000P
1000P
2200P
2200P
3.9K
3.9K
1000P
1000P
18K
18K
270P
270P
18K
2200P
560P
1K
2200P
18K
1K
560P
BA3314
KRA102M
TKTC3199
1SS133
KRC102M
47K
1500mA
1SS133
10/1610/16
10K
0.01
KRC102M
KRC102M
8.2K
1.5K
5.6K
8.2K
1.5K
5.6K
2.7K
100/10
1K
3.3K
KRC107M
0.01
0.01
KTA1271
KRC107M
4.7K
1/50
NJM78L05A
1SS133
47/10
0.01
100K
10K
220/25
KTA1271
47K
4.7K
22U
22U
22U
1K
1K
10/25
10/25
1.2K
1.2K
22/16
100P
100P
1K
1K
100P
1K
LC75342
220/16
100
12K
100K
12K
12K
22K
3.3K
1.2K
12K
22K
100K
3.3K
1.2K
3.9K
3.3K
3.3K
3.9K
6.8K6.8K
0.1
0.1
0.1
0.1
2700P
2700P
1/50 1/50
1/50
1/50
1/50
1/50
1/50
1/50
1/50
1/50
1SS133
1K
1K
0.01 0.01
RL153
RL153
RL153
RL153
0.01
0.01
15 14 13 12 11 10 9
12345678
891011 12 13 14
1234567
1
2
3
4
5
6
7
8
123
123456789101112131415
302928272625242322212019181716
1
2
3
4
5
6
7
8
9
10
11
12
13
14
S4950-1~2 R/P SW
S4904: MECHA MOTOR SW
SP471
SP481
LEFT
RIGHT
HEADPHONE
(1/2)
(2/2)
R
P
ALCNC OUT1NCOUT2NF2 NF3
NF1IN1GNDGNDVCCIN2FILTER
MAGNETIC
E HEAD
WOOFER
WOOFER
+
P
R
R/P
HEAD
-
(FUSE)
L-CH
R-CH
MOTOR
S4904
(FUSE)
(FUSE)
S4950-2
TO CD
(AMP BLOCK)
(MYLAR)
TO FRONT BLOCK
P
P
P
P
PPRR
R
R
R
R
S4950-1
S4950-5
S4950-6
S4950-7
S4950-8
S4950-4
S4950-3
L
OUTLBASS2LBASS1LTRELVRINLSELO
AUTUCDTA
TA CD TU AU
R
SELORVRINRTRERBASS1RBASS2ROUT
Vref
VSS CE DI
VDD CL
TESTNC
NCNC
RRRR
LLLL
T4981
T2.5A L 250V
+14V
FUSE(TH)
BW
BL
FU401
0
4.300.6
0
0.1
00 0
5.9
0.6 0.606.3
11.3 5.9 12.0 11.3 0 11.6
PLAY
REC
9.0
12.0
9.6
VOL_CLK
VOL_STB
VOL_DATA
PRODUCT SAFETY NOTICE
Each precaution in this manual should be followed during servicing. Components identified with the IEC symbol
!
!!
and mark in the parts list and the schematic
diagram designated components in which safety and performance can be of special significance. When replacing a component identified by
!
!!
and , use only the replacement parts designated, or parts with the same ratings of resistance, wattage or voltage that are designated in the parts list in this manual. Leakage­current or resistance measurements must be made to determine that exposed parts are acceptably insulated from the supply circuit before returning the product to the customer.
SCHEMATIC DIAGRAM (AMPLIFIER)
This is a basic schematic diagram.
Page 23
- 29 -- 28 -
WIRING DIAGRAM (AMPLIFIER)
This is a basic wiring diagram.
1
15
GND
CD-+B
CD-LCH
A-GND
CD-RCH
TU-LCH
TU-RCH
GND
E
RCLG
E
E
E
E
E
E
E
T2.5A L 250V
E
E
E
E
E
E
E
E
DIP
DIP
R4941
IC412
C4913
CN490
CN406
CN405
FU401
D4983
D4981
D4982
D4980
C4953
C4815
C4715
C4814
C4816
C4716
PR496
D4951
C4951
R4852
C4714
R4752
C4912
C4713
C4813
Q4851
J4313
L4902
C4918
C4811
C4711
C4804
C4704
C4909
J4310
Q4902
C4921
J4123
J4120
Q4904
C4905
J4226
J4334
J4217
C4851
C4751
Q4751
D4961
C4961
C4726
C4826
J4320
D4963
J4314
Q4903
Q4103
D4102
Q4104
D4962
Q4106
CN402
T002A 94V-0
CN421
C4901
J4222
J4335
J4223
CN411
IC410
R-OUT
L-OUT
S4950
J4117
D4953
J4224
J4220
J4221
J4329
C4963
C4962
1250
1500
LG401
Q4740
Q4840
J4307
J4205
J4107
J4330
C4110
Q4108
J4333
J4319
FCL41
FCL42
C4915
J4326
J4321
PR495
1AD4B10D2410A
J4106
J4219
J4218
J4104
J4343
L4881
L4781
J4130
L4780
J4131
J4229
R4952
R4951
Q4992
CN401
J4121
J4116
J4309
J4328
J4315
J4331
J4108
J4303
J4302
C4911
J4122
J4308
J4301
J4102
Q4951
J4202
J4300
J4203
J4201
J4200
VOL_CLK
J4101
J4119
J4332
J4312
J4215
CN480
J4114
(TO CD)
(TO FRONT)
SYNC_REC
VOL_STB
A_MUTE
VOL_DATE
TAPE_PLAY
AC_SENS
GND
+5.6V
ST_BY
BEAT
POWER_RY
QSOUND
J4124
J4324
J4225
J4311
J4325
J4317
J4100
NC
J4336
J4228
J4338 J4339
J4337
C4733
C4725
C4722
C4821
C4825
C4822
C4730
C4833
C4720
C4820
C4721
C4731
J4318
J4212
J4118
J4112
J4214
J4113
J4211
J4210
J4209
J4111
J4109
J4110
J4127 J4128
J4340
J4125
J4227
C4994
D4993
IC446
Q4995
J4129
Q4994
J4342
J4341
J4126
C4701
C4801
CN491
J4105
J4115
J4216
J4322
J4323
C4993
J4103
NIP CUT
C4981
C4981
C4982
C4982
C4983
C4983
C4980
C4980
C4952
C4952
R4818
R4818
R4905
R4905
C4803
C4803
R4810
R4810
R4804
R4804
R4803
R4803
R4710
R4710
R4703
R4703
R4911
R4911
C4709
C4709
C4812
C4812
R4816
R4816
R4961
R4961
R4962
R4962
R4901
R4901
C4807
C4807
R4827
R4827
R4831
R4831
R4731
R4731
R4728
R4728
R4822
R4822
R4828
R4828
C4729
C4729
C4728
C4728
C4829
C4829
R4825
R4825
R4924
R4924
R4953
R4953
R4954
R4954
R4955
R4955
R4862
R4862
C4981
C4982
C4983
C4980
C4952
R4718
R4818
R4905
C4803
C4707
R4705 C4705
R4805 C4805
R4810
R4804
R4803
C4802
C4706
C4806
R4710
C4703
R4704
C4702
R4703
R4912
R4910
C4919
R4911
C4920
C4916
R4914 C4906
C4708
R4708
C4709
R4709
R4809 C4809 R4808 C4808
C4712
C4812
R4816
R4716
R4756
R4961
R4856
R4717
R4817
R4107
R4962
R4781
R4901
R4938
R4991
R4857
R4758
R4858
R4757
R4859
R4759
R4881
R4110
R4108
C4750
C4850
R4105
R4104
C4984
C4807
R4106
IC411
R4821
R4827
R4831
R4725R4731
R4728R4722
R4822
R4828
C4729
C4827
C4828
C4727
C4728
R4732
C4923
R4923
C4922
R4922
R4963
C4829
R4832
R4825
R4726
R4720
R4820
R4826
R4727 R4721
C4924
R4924
C4997
R4953
R4954R4955
R4761 R4760
R4861 R4860 R4862
R4762
Page 24
- 31 -- 30 -
SANYO Electric Co., Ltd.
Osaka, Japan
Mar. / '04 BB Printed in Japan
BW
BL
RE
BK
1AD4B10D2410E
T002A 94V-0
L4591
CN451
CN452
CN455
S6003
S6004
S6005
S6006
SOUND PRESET
BASS
SURROUND
CLOCK
TIME
1AD4B10D2410F
T002A 94V-0
KEY0
GND
CN604
R6005R6004R6003
WIRING DIAGRAM (POWER TRANSFORMER & KEY)
KEYP.W.BOARD
POWER TRANSFORMER P.W. BOARD
This is a basic wiring diagram.
Loading...