Sanyo CE52LH1WP User Manual

CE52LH1WP

Instruction Manual Manuel d'utilisation Manual de instrucciones

LCD Monitor Moniteur d'affichage à cristaux liquides Monitor de LCD

Please read this Instruction book before using your LCD monitor. We wish you many hours of pleasure from your new LCD monitor. Veuillez lire attentivement ce mode d’emploi avant d’utiliser votre moniteur d’affichage à cristaux liquides. Nous espérons que votre

nouveau dispositif d'affichage vous procurera de nombreux instants de bonheur. Lea este manual de instrucciones antes de usar su nuevo monitor. Deseamos que disfrute de él muchas horas.

English Page 2~15 Français Page 16~28

Español Página

29~41

Downloaded From TV-Manual.com Manuals

SAFETY

PRECAUTIONS

Do not allow anything to rest on the power

cord. Do not locate this LCD monitor where the cord will be damaged by people walking on it.

Do not overload wall outlets and extension cords as this can result in fire or electric shock.

A suitable socket outlet must be provided near to the monitor and shall be easily accessible. Do not place this LCD monitor near any heat sources such as radiators, heaters, stoves and other heat-generating products (including amplifiers). Do not place your LCD monitor on an unstable stand, shelf or table. Serious injury to an individual, and damage to the LCD monitor may result if it should fall. Your sales person can recommend an approved wall mounting kit. Aspecial wall mounting kit is available for this model.

This LCD monitor should be operated only from the type of power

source indicated on the monitor or as indicated in the Operating Instructions. If you are not sure of the type of power supply, consult your sales person or your local power company.

For added protection it is strongly recommended that this LCD

monitor has its mains supplied via an approved earth fault

protection device.

WARNING: To prevent injury the LCD monitor must be securely

attached to the wall in accordance with the manufacturers installation instructions.

IMPORTANT:

This product must be earthed

This unit is not disconnected from the mains unless the mains lead is unplugged. The installer must make sure that the waterproof inline coupler is easily accessible.

This monitor is tested to IP66 standard rating. This monitor is not

protected against temporary or continuous

immersion in liquid. Do not use immediately after moving the LCD monitor from a low

temperature to a high temperature environment, as this causes condensation, which may result in fire, electric shock, or other hazards. Before cleaning, unplug the monitor from the wall socket.

Do not mount near an open flame source. Open flames must never be used near this LCD monitor. This LCD monitor should not be built in or enclosed in any way, heat build up will reduce the life of the monitor.

This LCD monitor should have a minimum distance of 5cm away from the wall and the monitor should have 10cm distance around the top and sides. Always mount using recommended and substantial fixtures and fittings.

The rear finned section around the cabinet functions as a heat sink, removing heat away from the monitor. The external surface of the cabinet (finned area) must not be covered or the airflow restricted in anyway by enclosing the LCD monitor.

The operating temperature range of this monitor is guaranteed 0°C ~ 40°C/32°F ~ 104°F. It is not recommended to install the screen in direct sunlight without adequate shading, as this will cause the temperature of the panel to rise above the maximum specified. Doing so may cause a black shadow to appear on the screen which will disappear when the screen temperature returns to within the specification. This “of course” does not produce any harmful effect on the lifetime of the monitor

Do not apply liquid cleaners or aerosol cleaners directly onto the LCD monitor. Use a damp cloth for cleaning.

ADDITIONAL FOR NORTH AMERICA AND CANADA: This monitor must NOT

be permanently mounted to the building structure. It must be mounted in such a way that it can be removed using basic tools. The power supply cord must NOT

be attached to the building

surface. The power supply cord must NOT

be routed through walls, ceiling, floors, or other similar openings in the building structure. The power supply cord MUST

be positioned so as to prevent

physical damage.

Installation and Use

CAUTION: Please read and retain for your safety. This unit has been designed and manufactured to assure your personal safety, but

improper use can result in potential electric shock or fire hazards. In order not to defeat the safeguards incorporated in this monitor observe the following basic rules for its installation, use and servicing.

Important: (UK only)

THIS PRODUCT MUST BE EARTHED

This equipment is fitted with an approved mains lead and an approved non rewireable UK mains plug. To change a fuse in this type of plug proceed as follows:

1. Remove the fuse cover and fuse.

2. Fit a new fuse which should be a BS1362 13 Amp A.S.T.A. or

BSI approved type.

3. Ensure that the fuse cover is correctly refitted. If the fuse cover is lost or damaged the plug must NOT be used

but replaced with a serviceable plug. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a rating of 13 Amp, ensure the fuse cover is correctly fitted. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 13 Amp.

Note: The severed plug must be destroyed to avoid a possible

shock hazard should it be inserted into a 13 Amp socket elsewhere. The wires in this mains lead are coloured in accordance with the

following code:

Blue -------> Neutral Brown ----> Live Green and Yellow ----> Earth

1. The Blue wire must be connected to the terminal whichis

marked with the letter “N” or coloured BLACK.

2. The Brown wire must be connected to the terminal with the letter “L” or coloured RED.

3. The Green and Yellow wire must be connected to the terminal which is marked with the letter “E” or coloured GREEN or GREEN and YELLOW.

Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the wires.

Do not attempt to bypass the safety purpose of the grounding type plug.

THIS UNIT IS NOT DISCONNECTED FROM THE MAINS UNLESS THE MAINS LEAD IS UNPLUGGED.

THE INSTALLER MUST MAKE SURE THE MAINS LEAD IS EASILY ACCESSIBLE.

10cm

5cm

Downloaded From TV-Manual.com Manuals

Important recycling information.

Your SANYO product is designed and manufactured with high quality materials and components which can be recycled and reused.

This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately.

In the European Union there are separate collection systems for used electrical and electronic products.

Please help us to conserve the environment we live in! Note: This symbol mark and recycle system are applied only to

EU countries are not applied to other countries of the world.

Your monitor is fully transistorised and does not contain any user serviceable components. You must not remove the rear cover of the monitor by yourself. The apparatus is working with high voltages and could damage

objects or even endanger people. Leave all required repair and service jobs to an authorised service technician. He will exclusively use such spare parts that are complying with the same safety standards as applicable to the original parts. The use of original spare parts can prevent fire, shock and other hazards.

Unplug the LCD monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions:

 If the power cord or plug is damaged.

 If liquid has been spilt in to the LCD monitor.

 If the LCD monitor has been exposed to rain or water.

 If the LCD monitor has been dropped or the cabinet has been damaged.

 If the LCD monitor exhibits a distinct change in performance.

 If the LCD monitor does not operate normally by following the operating instructions.

Adjust only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage. This will often require extensive work by a qualified technician to restore the monitor to normal operation.

Servicing

SERVICING

Downloaded From TV-Manual.com Manuals

The product (meaning the equipment or appliance to which this documentation relates) incorporates Software (the software applications, utilities and modules embedded within the Product) which is owned by Sanyo or its licensors. Before using the product, please read the End-User License Conditions detailed below. If you do not agree to the terms and conditions of the End-User License, Please do not proceed to use the Product- repack the Product unused and return it to your supplier together with proof of purchase for a full refund. By using the product, you agree to be bound by the terms and conditions of the End-User License.

License Grant, Conditions and restrictions

1. Sanyo grants you a non-exclusive, world-wide (subject to export

controls), non-transferable (except as permitted by 2 below), royalty-free license to use the Software upon and with the Product.

2. You may not transfer any of your license rights in the Software

without the prior written consent of SANYO and if consent is provided then the Software shall only be transferred in conjunction with the transfer of the Product AND provided that the transferee has read and agreed to accept the terms and conditions of this license.

3. You must ensure that the copyright, trademark and other protective

notices contained in the Software are maintained and not altered or removed.

4. The Software provided hereunder is copyrighted and licensed (not

sold). SANYO especially does not transfer title or and ownership rights in the Software to you. The Software provided hereunder may contain or be derived from portions of materials provided to SANYO under license by a third party supplier.

5. Except as expressly permitted by statute you may not;

 use the Software in conjunction with any other computer

hardware other than the product;

 copy all or part of the Software;  incorporate all (or any of) the Software into other programs

developed by (or on behalf of) you and/or used by you;

 reverse-engineer, decompile or disassemble the Software;  make the Software (or any part of it) available, or permit its

redistribution, for use with any computer hardware other than the Product; or rent, lease, gift, loan, sell, distribute or transfer possession of the whole or any part of the Software.

Termination

This license is effective until terminated. This license will terminate automatically without notice if you fail to comply with any of its provisions.

Disclaimer

1. The Software is(to the extent permitted by law) supplied ‘as is’ and

SANYO and its suppliers expressly exclude all warranties, express or implied, including (but not limited to) warranties of satisfactory quality, fitness for purpose and non-infringement (save to the extent that the same are not capable of exclusion at law).

2. In no circumstances will SANYO be liable for any direct, indirect,

consequential, or incidental damage (including loss of profits, business interruption, loss of data or the cost of procurement of substitute goods, technology or services) arising out of the use or the inability to use the Software (save to the extent that such liability is not capable of exclusion at law).

General

1. This End-User License will be governed by laws of England and

the User may only bring claims in the English Courts and SANYO shall be entitled to bring a claim in the courts of any jurisdiction.

2.This End-User License is governed by the laws of the State of

California. The End-User and Sanyo agree that any action to enforce or interpret the terms of this End-User License shall be brought only in the appropriate state or federal court located in Los Angeles County, California.The End-User and Sanyo hereby submit to the exclusive jurisdiction and venue of such court.

3. The above terms and conditions supersede any prior agreement,

oral or written, between you and SANYO relating to the Software.

End-User License

Model Number : CE52LH1WP Trade name : Sanyo Responsible party : SANYO FISHER COMPANY Address : 21605 Plummer Street, Chatsworth, California 91311 Telephone : (818) 998-7322

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interence that may cause undesired operation.

Declaration of Conformity: North America and Canada

The AC Power Cord supplied with this LCD monitor meets the requirement for use in the country in which you purchase it.

AC Power Cord for the United States and Canada:

AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA). AC Power Cord has a grounding-type AC line plug. This is a safety feature to make sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable to insert the plug into the outlet, contact your electrician.

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE

AC Power Cord Requirement

GROUND

Downloaded From TV-Manual.com Manuals

 Connect the display unit to VGA, BNC and Scart connector as

required.

1. Connect the in-line power connector to the Mains Inlet as shown above.

2. Connect the power cord of the LCD monitor to a suitable wall outlet.

 As this product does not have a mains On/Off switch, please

ensure your mains plug is easily accessible.

 The LCD monitor is prepared for a mains voltage AC100~240V,

50Hz/ 60Hz. To completely switch off the mains, or when the display unit is not to be used for an extended period of time, it is advisable to disconnect the power cord from the power outlet.

Please use the correct mains lead supplied with the set for your

area.

3. Warning: To prevent injury, the unit must be securely attached to the wall in accordance with the installation instructions.

 INPUT selection To switch between AV1, RGB, AV2, AV3, PC, DVI or Network press the INPUT button on your remote control repeatedly.

1. AV1

SCART connection / CVBS / RGB / S-VIDEO.

2. RGB

TTL input (5V RGB signals) into SCART terminal

Y,Pb,Pr/ RGBHV connection (AV2)

This LCD monitor has a choice of Y, Pb, Pr or RGB H/V connections. You can connect your DVD player to the Y, Pb, Pr terminals instead of using a scart lead. This can support high definition in analogue component form. RGB H/V can be used as a PC input via the BNC terminals.Both options support a large range of resolutions (page 15).

AV3

Composite (CVBS) signal input AV3 OUT is to output the composite video signal from the VIDEO IN so that you can connect monitors with the use of a loop through function.

5. DVI-D (Digital Video Interface)

This monitor has a DVI connector. This is located at the back of the monitor next to the phono sockets. This input will support a large range of resolutions as shown on page 14. See page 7 for details of menu operation.

6. PC connection

This LCD monitor has a PC connector (PC-IN D-SUB). You can connect a PC to the LCD monitor and use it as a monitor display (see page 9). This input will support a large range of resolutions (see page

14). Audio can be connected via the 3.5mm PC audio in socket.

7. LD Net IN: Has the ability for LD-NET to be connected to control the monitor using a network.

8. External Audio Output

To output the audio signal from AV1, AV2, AV3, PC and DVI. The speaker impedance should be 8 ohms.

9. Use of Monitor Audio Output Connections

The audio monitor out sockets on the rear of the set provide a fixed level audio output for reproducing sound via your audio equipment.

INST

ALLA

TION

Step : 1 Mains Connection

WARNING! High voltages are used in the operation of

this set. Refer service to qualified service personnel.

Step : 2 Connections

LD-Net

Mains Inlet

AV2-IN

AC Mains Outlet

N5VW

AV2-IN

AV2-I N

Downloaded From TV-Manual.com Manuals

REMOTE CONTROL

Remote control battery installation

Install two "AA" 1.5 volt batteries so that the "+" and "-" marks on the batteries match the "+" and "-" marks inside the unit into the remote control handset.

Standby

To switch the monitor on and off. Also see page 7.

Recall

To display input selection information and the Time set. You can also select colour systems in AV1 / AV3 mode as follows: AUTO-> PAL -> SECAM -> NTSC -> NTSC4.43 -> PALM ->PAL N. It can also be automatically adjusted in PC mode by pressing this button for twice .

Up and Down

To select the next or previous item.

Bass Expander

To get an emphasised bass sound ON or OFF.

Back

Used to return to the previous menu.

Input

To switch input source from AV1, RGB, AV2, AV3, PC, DVI or Network mode.

Wide

To select the screen mode Full, Full All, Zoom 16:9, Title in 16:9, Zoom 14:9, Title in 14:9, Normal or Natural wide,.

Refer to page 11.

To enter and exit the main menu, and sub menu.

Level Up/Down

To adjust the sound volume level or enter sub menus

Picture mode selector

Press the ->.<- button repeatedly to select the following picture mode.

Personal-Personal preference mode. Standard-Normal viewing mode. Dynamic-Suitable for brightly lit rooms. Soft- Low contrast setting Eco-Suitable for dimly lit rooms and gives a cinema-like

effect.

F/OK

To confirm the initial setting in the menu.

Freeze

To switch picture still on or off.

TXT/TV

To select Teletext mode.

Main/Sub Picture Swap

To swap Main and Sub picture.

ON/OFF

To switch OFF ->PIP(1) ->PIP(2) ->POP mode in turn. Refer to page 12.

Green

Press this button for more than 5 seconds, installation mode will appear.

Sound Mute

To mute the sound from the speakers. The sound changes as follows : Normal volume <-> Mute

FOR EU USERS

The symbol mark and recycling systems described below apply to EU countries and do not apply to countries in other areas of the world. Your SANYO product is designed and manufactured with high quality materials and components which can be recycled and/or reused.

The symbol mark means that electrical and electronic equipment, batteries and accumulators, at their end-of-life, should be disposed of separately from your household waste.

In the European Union there are separate collection systems for used electrical and electronic equipment, batteries and accumulators. Please, dispose of them correctly at your local community waste collection/recycling centre.

Please, help us to conserve the environment we live in!

Downloaded From TV-Manual.com Manuals

+ 12 hidden pages