Sanyo CE42LM6WP User Manual

INSTRUCTION MANUAL CE42LM6R

CE42LM6DPB CE42LM6WP CE42SR2

LCD Monitor

CE52LH2R CE52LH2WP CE52SR2

Please read this Instruction book before using your LCD monitor. We wish you many hours of pleasure from your new LCD monitor.

GB GB

TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY PRECAUTIONS ....................... 3

Installation and Use .............................. 3

SERVICING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Federal Communications Commission Notice . . . . . . . . . 4

AC Power Cord Requirement . . . . . . . . . . . . . . . . . . . . . . 5

End-User License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

INSTALLATION .............................. 6

Step: 1 Mains Connection ......................... 6

Step: 2 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Remote control battery installation . . . . . . . . . . . . . . . . . . 7

Controls and Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Menu Operation ................................. 8

Picture menu ................................... 8

MENU OPERATION ........................... 9

Picture menu ................................... 9

Sound menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Time menu ..................................... 9

Setup menu .................................... 9

PC Adj. menu ...................................10

INSTALLATION MODE ........................11

Installation Mode ................................11

OPERATION ................................ 12

Selection of picture size . . . . . . . . . . . . . . . . . . . . . . . . . .12

PIP/POP Operation ..............................13

OPERATION (IN TEXT MODE) . . . . . . . . . . . . . . . . . 14

Teletext Operation ...............................14

SPECIFICATIONS/HELPFUL HINTS . . . . . . . . . . . . 15

Speciﬁcation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Helpful hints ....................................15

DIMENSIONS ............................... 16

PC/DVI-D/COMPONENT SIGNAL SUPPORT

TIMING LIST ................................ 17

RS232C COMMAND TABLES .................. 18

Robust monitor (CE42LM6R, CE42LM6DPB, CE52LH2R)

The robust monitor can be used in a wide variety of environments for dusty and oily circumstance such as fast food, digital signage, industrial and public display.

¡NON GLARE ACRYLIC PANEL

This monitor set has a non glare acrylic panel. This offers the protection for the panel surface in the public display applications and easy

to clean the panel.

¡ALUMINUM CABINET & NON HOLES DESIGN

This monitor set uses Anodized aluminum and it has quite unique “Non-Holes” ventilation design which protects against mischief in the

public display applications and less maintenance when used in a dusty or oily environment.

Weather proof monitor (CE42LM6WP, CE52LH2WP)

Weather resistant and water proof in accordance with the IP66 standard.

¡ANTI REFLECTION TAMPER GLASS

This monitor set has a tough anti refection tampered glass. This offers the protection for the panel surface in the public display circum-

stance.

¡ALUMINUM CABINET & NON HOLES DESIGN

This monitor set uses Anodized aluminum and it has quite unique “Non-Holes” ventilation design which protect against mischief in the

public display applications and less maintenance from dust and oil circumstance, and having perfect protection of IP66 weather-resistant approval.

Daylight readable monitor (CE42SR2, CE52SR2)

In addition to Weather proof monitor, it has adaptive brightness in accordance with prevailing light conditions.

¡EXTENSIVE INPUT & OUTPUT TERMINALS (for all products)

This monitor set has various input and output terminals including component (Y,Pb,Pr) or RGBHV input and output with 5-BNC, compos-

ite video input and output with BNC, and RS-232 control port (serial D-Sub 9) input and output which offer the daisy chain connection. There are computer inputs (a D-Sub 15 RGB terminal) and DVI-D input with HDCP for High deﬁnition signals. There are also jacks for external speakers.

Trademarks

Each name of corporations or products in this book is either a registered trademark or a trademark of its respective corporation.

10cm

5cm

GB GB

SAFETY PRECAUTIONS

CAUTION: Please read and retain for your safety. This unit has been designed and manufactured to assure your personal safety, but

improper use can result in potential electric shock or ﬁre hazards. In order not to defeat the safeguards incorporated in this monitor observe the following basic rules for its installation, use and servicing.

Installation and Use

Do not allow anything to rest on the power cord. Do not locate this LCD monitor where the cord will be damaged by people walking on it.

Do not overload wall outlets and extension cords as this can result in ﬁre or electric shock. A suitable socket outlet must be provided near

to the monitor and shall be easily accessible. Do not place this LCD monitor near any heat sources such as radiators, heaters, stoves and other heat-generating products (including ampliﬁers). Do not place your LCD monitor on an unstable stand, shelf or table. Serious injury to an individual, and damage to the LCD monitor may result if it should fall. Your sales person can recommend an approved wall mounting kit. A special wall mounting kit is available for this model.

This LCD monitor should be operated only from the type of power source indicated on the monitor or as indicated in the Operating Instructions. If you are not sure of the type of power supply, consult your sales person or your local power company.

For added protection it is strongly recommended that this LCD monitor has its mains supplied via an approved earth fault protection device.

WARNI NG: To prevent injury the LCD monitor must be securely

attached to the wall in accordance with the manufacturers installation instructions.

IMPORTANT:

This product must be earthed.

This unit is not disconnected from the mains unless the mains lead is unplugged. The installer must make sure that the waterproof inline coupler is easily accessible.

(CE42LM6WP/CE42SR2/CE52LH2WP/CE52SR2 model only)

This monitor is tested to IP66 standard rating. This monitor is not protected against temporary or continuous immersion in liquid.

Do not use immediately after moving the LCD monitor from a low temperature to a high temperature environment, as this causes condensation, which may result in ﬁre, electric shock, or other hazards. Before cleaning, unplug the monitor from the wall socket.

Do not mount near an open ﬂame source. Open ﬂames must never be used near this LCD monitor. This LCD monitor should not be built in or enclosed in any way, heat build up will reduce the life of the monitor.

This LCD monitor should have a minimum distance of 5cm away from the wall and the monitor should have 10cm distance around the top and sides. Always mount using recommended and substantial ﬁxtures and ﬁttings.

The rear ﬁnned section around the cabinet functions as a heat sink, removing heat away from the monitor. The external surface of the cabinet (ﬁnned area) must not be covered or the airﬂow restricted in anyway by enclosing the LCD monitor.

(CE42LM6WP/CE42SR2/CE52LH2WP/CE52SR2 model only)

The operating temperature range of this monitor is guaranteed 0°C ~ 40°C/32°F ~ 104°F. It is not recommended to install the screen in direct sunlight without adequate shading, as this will cause the temperature of the panel to rise above the maximum speciﬁed. Doing so may cause a black shadow to appear on the screen which will disappear when the screen temperature returns to within the speciﬁcation. This “of course” does not produce any harmful effect on the lifetime of the monitor.

Do not apply liquid cleaners or aerosol cleaners directly onto the LCD monitor. Use a damp cloth for cleaning.

ADDITIONAL FOR NORTH AMERICA AND CANADA:

This monitor must NOT be permanently mounted to the building

structure. It must be mounted in such a way that it can be removed using basic tools. The power supply cord must NOT be attached to the building surface. The power supply cord must NOT be routed through walls, ceiling, ﬂoors, or other similar openings in the building structure. The power supply cord MUST be positioned so as to prevent physical damage.

Important: (UK only)

THIS PRODUCT MUST BE EARTHED.

This equipment is ﬁtted with an approved mains lead and an approved non rewireable UK mains plug. To change a fuse in this type of plug proceed as follows:

1. Remove the fuse cover and fuse.

2. Fit a new fuse which should be a BS1362 13 Amp A.S.T.A. or

BSI approved type.

3. Ensure that the fuse cover is correctly reﬁtted.

If the fuse cover is lost or damaged the plug must NOT be used but replaced with a serviceable plug. If the ﬁtted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug ﬁtted in its place. If the mains plug contains a fuse, this should have a rating of 13 Amp, ensure the fuse cover is correctly ﬁtted. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 13 Amp.

Note: The severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13 Amp socket elsewhere.

The wires in this mains lead are coloured in accordance with the following code:

Blue Neutral Brown Live Green and Yellow Earth

1. The Blue wire must be connected to the terminal which is

marked with the letter “N” or coloured BLACK.

2. The Brown wire must be connected to the terminal with the letter “L” or coloured RED.

3. The Green and Yellow wire must be connected to the terminal which is marked with the letter “E” or coloured GREEN or GREEN and YELLOW.

Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the wires.

Do not attempt to bypass the safety purpose of the grounding type plug.

THIS UNIT IS NOT DISCONNECTED FROM THE MAINS UNLESS THE MAINS LEAD IS UNPLUGGED.

THE INSTALLER MUST MAKE SURE THE MAINS LEAD IS EASILY ACCESSIBLE.

GB GB

SERVICING

Servicing

Your monitor is fully transistorised and does not contain any user serviceable components.

You must not remove the rear cover of the monitor by yourself. The apparatus is working with high voltages and could damage objects or even endanger people. Leave all required repair and service jobs to an authorised service technician. He will exclusively use such spare parts that are complying with the same safety standards as applicable to the original parts. The use of original spare parts can prevent ﬁre, shock and other hazards.

Unplug the LCD monitor from the wall outlet and refer servicing to qualiﬁed service personnel under the following conditions:

n If the power cord or plug is damaged.

n If liquid has been spilt in to the LCD monitor.

n If the LCD monitor has been dropped or the cabinet has been damaged.

n If the LCD monitor exhibits a distinct change in performance.

n If the LCD monitor does not operate normally by following the operating instructions.

n If the LCD monitor has been exposed to rain or water. (CE42LM6R/CE42LM6DPB/CE52LH2R model only)

Adjust only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage. This will often require extensive work by a qualiﬁed technician to restore the monitor to normal operation.

Important recycling information.

Your SANYO product is designed and manufactured with high quality materials and components which can be recycled and reused.

This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately.

In the European Union there are separate collection systems for used electrical and electronic products.

Please help us to conserve the environment we live in! Note: This symbol mark and recycle system are applied only to EU countries are not applied to

other countries of the world.

Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Do not make any changes or modiﬁcations to the equipment unless otherwise speciﬁed in the instructions. If such changes or modiﬁcations should be made, you could be required to stop operation of the equipment.

Canadian Radio Interference Regulations

This Class A digital apparatus meets all requirements of the Canadian ICES-003.

WARNI NG

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

GB GB

SERVICING

AC Power Cord Requirement

The AC Power Cord supplied with this LCD monitor meets the requirement for use in the country in which you purchase it.

AC Power Cord for the United States and Canada:

AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certiﬁed by the Canadian Standard Association (CSA).

AC Power Cord has a grounding-type AC line plug. This is a safety feature to make sure that the plug will ﬁt into the power outlet. Do not try to defeat this safety feature. Should you be unable to insert the plug into the outlet, contact your electrician.

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE

GROUND

End-User License

The product (meaning the equipment or appliance to which this documentation relates) incorporates Software (the software applications, utilities and modules embedded within the Product) which is owned by Sanyo or its licensors. Before using the product, please read the End-User License Conditions detailed below. If you do not agree to the terms and conditions of the End-User License, Please do not proceed to use the Product- repack the Product unused and return it to your supplier together with proof of purchase for a full refund. By using the product, you agree to be bound by the terms and conditions of the End-User License.

License Grant, Conditions and restrictions

1. Sanyo grants you a non-exclusive, world-wide (subject to export controls), non-transferable (except as permitted by 2 below), royalty-free

license to use the Software upon and with the Product.

2. You may not transfer any of your license rights in the Software without the prior written consent of SANYO and if consent is provided then the Software shall only be transferred in conjunction with the transfer of the Product AND provided that the transferee has read and agreed to accept the terms and conditions of this license.

3. You must ensure that the copyright, trademark and other protective notices contained in the Software are maintained and not altered or removed.

4. The Software provided hereunder is copyrighted and licensed (not sold). SANYO especially does not transfer title or and ownership rights in the Software to you. The Software provided hereunder may contain or be derived from portions of materials provided to SANYO under license by a third party supplier.

5. Except as expressly permitted by statute you may not;

¡use the Software in conjunction with any other computer hardware other than the product;

¡copy all or part of the Software;

¡incorporate all (or any of) the Software into other programs developed by (or on behalf of) you and/or used by you;

¡reverse-engineer, decompile or disassemble the Software;

¡make the Software (or any part of it) available, or permit its redistribution, for use with any computer hardware other than the Product; or

rent, lease, gift, loan, sell, distribute or transfer possession of the whole or any part of the Software.

Termination

This license is effective until terminated. This license will terminate automatically without notice if you fail to comply with any of its provisions.

Disclaimer

1. The Software is(to the extent permitted by law) supplied “as is” and SANYO and its suppliers expressly exclude all warranties, express or

implied, including (but not limited to) warranties of satisfactory quality, ﬁtness for purpose and non-infringement (save to the extent that the same are not capable of exclusion at law).

2. In no circumstances will SANYO be liable for any direct, indirect, consequential, or incidental damage (including loss of proﬁts, business interruption, loss of data or the cost of procurement of substitute goods, technology or services) arising out of the use or the inability to use the Software (save to the extent that such liability is not capable of exclusion at law).

General

1. This End-User License will be governed by laws of England and the User may only bring claims in the English Courts and SANYO shall be

entitled to bring a claim in the courts of any jurisdiction.

2. This End-User License is governed by the laws of the State of California. The End-User and Sanyo agree that any action to enforce or interpret the terms of this End-User License shall be brought only in the appropriate state or federal court located in Los Angeles County, California.The End-User and Sanyo hereby submit to the exclusive jurisdiction and venue of such court.

3. The above terms and conditions supersede any prior agreement, oral or written, between you and SANYO relating to the Software.

GB GB

INSTALLATION

Step: 1 Mains Connection

n Connect the display unit to VGA, BNC and Scart con-

nector as required.

* This ﬁgure is 42 inch model.

1. Connect the in-line power connector to the Mains Inlet as shown above.

2. Connect the power cord of the LCD monitor to a suitable wall

outlet.

✐ As this product does not have a mains On/Off switch, please

ensure your mains plug is easily accessible.

✐ The LCD monitor is prepared for a mains voltage AC100 ~ 240V,

50Hz/ 60Hz. To completely switch off the mains, or when the display unit is not to be used for an extended period of time, it is advisable to disconnect the power cord from the power outlet.

LD-Net

4. AV3

Composite (CVBS) signal input. AV3-OUT can be used to output the incoming AV3 signal to the other monitor.

5. DVI-D (Digital Video Interface)

DVI-D supports a large range of resolutions as shown on page 17.

AC Mains Outlet

✐ Please use the correct mains lead supplied with the set for your

area.

3. Warning: To prevent injury, the unit must be securely attached to the wall in accordance with the installation instructions.

WARNI NG! High voltages are used in the

operation of this set. Refer service to qualiﬁed service personnel.

Step: 2 Connections

n INPUT selection

To switch either AV1, RGB, AV2, AV3, PC, DVI or Network by pressing the INPUT button on your remote control repeatedly.

1. AV1

SCART connection/CVBS/RGB/S-VIDEO.

2. RGB

TTL input (5V RGB signals) into SCART terminal.

3. Y, Pb, Pr/RGBHV connection (AV2)

Choose Y, Pb, Pr or RGB H/V connection by selecting AV2 Setting in Set up menu (see page 10). You can connect your DVD player to the Y, Pb, Pr terminals instead of using a scart lead. This can support high deﬁnition in analogue component form. RGB H /V can be used as a PC input via the BNC terminals. Both options support a large range of resolutions (page 17). AV2-OUT can be used to output the incoming AV2 signal to the other monitor.

6. PC connection

PC input (PC-IN D-SUB). This input supports a large range of resolutions as shown page 17. Audio can be connected via the 3.5mm PC-AUDIO IN.

7. External Speaker

Output the audio signal from AV1, AV2, AV3, PC and DVI. The speaker impedance is 8 ohms.

8. AV2 / DVI AUDIO IN

Connect the audio output (stereo) from a computer or video equipment connected AV2 or DVI.

9. Monitor Audio OUT

This terminals output ﬁxed level from AUDIO IN.

10. RS232C IN/OUT

When the monitor is controlled by a computer, connect to this jack

with serial control cable. You can connect to another monitor with RS232C OUT. When you connect PC with RS232C, select “ON” at Network standby in Installation mode. If it is selected “OFF”, RS232C terminals do not functional. Also select push button to “SERIAL POART”.

GB GB

INSTALLATION

Remote control

Input

To switch input source from AV1, RGB, AV2, AV3, PC, DVI or Network mode.

Wide

To select the screen mode Full, Full All, Zoom 16: 9, Title in 16:9, Zoom 14:9, Title in 14:9, Normal or Natural wide.

Refer to page 12.

To enter and exit the main menu, and sub menu.

Level Up/Down

To adjust the sound volume level or enter sub menus.

F/OK

To conﬁrm the initial setting in the menu.

Picture mode selector

Press the 9 button repeatedly to select the following picture mode.

Personal - Personal preference mode. Standard - Normal viewing mode. Dynamic - Suitable for brightly lit rooms. Soft - Low contrast setting Eco - Suitable for dimly lit rooms and gives a

cinema-like effect.

Freeze

To switch picture still on or off.

Green

Press this button for more than 5 seconds, installation mode will appear.

Standby

To switch the monitor on and off. Also see page 8.

Recall

To display input selection information and the Time set. You can also select colour systems in AV1/AV3 mode as follows: AUTO \ PAL \ SECAM \

NTSC \ NTSC4.43 \ PAL M \ PAL N.

Auto PC

It can also be automatically adjusted in PC mode by pressing this button for twice .

Back

Used to return to the previous menu.

Up and Down

To select the next or previous item.

Sound Mute

To mute the sound from the speakers. The sound changes as follows: Normal volume [\

Mute.

Bass Expander

To get an emphasised bass sound ON or OFF.

TXT/TV

To select Teletext mode.

Main/Sub Picture Swap

To swap Main and Sub picture.

ON/OFF

To switch OFF \ PIP(1) \ PIP(2) \ POP mode in turn. Refer to page 13.

Remote control battery installation

Install two “AA” 1.5 volt batteries so that the “+” and “–” marks on the batteries match the “+” and “–” marks inside the unit into the remote control handset.

FOR EU USERS

The symbol mark and recycling systems described below apply to EU countries and do not apply to countries in other areas of the world. Your SANYO product is designed and manufactured with high quality materials and components which can be recycled and/or reused.

The symbol mark means that electrical and electronic equipment, batteries and accumulators, at their end-of-life, should be disposed of separately from your household waste.

Note:

If a chemical symbol is printed beneath the symbol mark, this chemical symbol means that the battery or accumulator contains a heavy metal at a certain concentration. This will be indicated as follows: Hg: mercury, Cd: cadmium, Pb: lead

In the European Union there are separate collection systems for used electrical and electronic equipment, batteries and accumulators. Please, dispose of them correctly at your local community waste collection/recycling centre.

Please, help us to conserve the environment we live in!

INSTALLATION

Picture

Brightness Contrast Color Tint (only if NTSC equipment is detected) Sharpness White Tone

White Tone / R / G / B

Advanced Setting

DCDi / ACC/ACM / CCS / DNR / MPEG NR / Film Mode

Sound

Treble Bass Balance

Bass Expander

On / Off

Time

Setup

PC Adj.

Current Time Schedule Weekday

On Program

AV1 / RGB / AV2 / AV3 / PC / DVI / Network

Menu Setup PIP / POP Setup Initial Settings Text Language Tile Mode AV2 Setting

Western / Eastern / Russian / Arabic / Farsi

Tile Mode Active / H/V_Sets / H/V Location / Bezel H/V Adjustment

RGBHV / YPbPr

Auto Adjust H-Position V-Position Clock

Phase

Language / H/V-Position / Duration / Transparence

PIP/POP Mode / Main/Sub Source / PIP Position

Time Action

Active

Power On / Power Off

On / Off

1 - 20

Current Weekday

Native Resolution PC Power save

XGA / WXGA 1366x768

On / Off

GB GB

Controls and Menus

The LCD display has a Standby light to show there is power.

Switching into /from standby mode

The Standby mode is used for switching the LCD monitor off for short periods of time. In standby mode the monitor is switched off but is still receiving mains power.

¡To turn the monitor into standby mode, press the 4 button.

The blue power indicator illuminates more brightly.

¡To turn the monitor ON from standby mode, press the 4 button

again.

Menu Operation

Many of your monitors functions are controlled through the menu function, using the remote control.

During menu operation the bottom of the on screen display will show which controls can be used for menu navigation. Press the MENU button to enter the main menu. Whenever main menu is accessed initially, PICTURE will be the default selection.

A sub menu is selected using the 5 or 6 button and pressing the 1 or 2 button when the required sub menu is highlighted. When you have ﬁnished you can press the BACK button to return to the previous menu, press the MENU button to exit the menu operation.

Control buttons (bottom corner of back cover)

Menu button: Used to display or cancel main menu.

Input/d button: Switch between AV1, RGB, AV2, AV3, PC , DVI

1 or 2 buttons: provide up and down adjustments.

4 button: To switch to standby mode (to switch off completely

If you ﬁnd the power indicator ﬂashing, disconnect power cord from the power outlet and contact our Service desk.

This warning is a sign to let you know that the power protection function of this TV set is now operating.

or Network mode. It is also used to provide sub menu selection from the Main Menu.

disconnect the monitor from the power supply).

Picture menu

1. Press the MENU button. PICTURE will be the default selection.

Press the 1 or 2 button to enter. Set the picture settings for your “personal” preference.

2. Use the 5 or 6 button to select eg. Brightness and the 1 or 2 button to adjust levels.

n White Tone

May be used to adjust the color tone of the picture. Use the 5 or 6 button to select White Tone and press the 1 or 2 button

to enter the sub menu. You can select Personal, Cool, Standard or Warm settings by using the 1 or 2 button. To adjust the color tone of the picture by using the 5 or 6 button to select Red(R), Green(G) or Blue(B) and the 1 or 2 button to adjust levels.

These settings will be stored in personal mode automatically.

GB GB

MENU OPERATION

Picture menu

n Advanced settings

Use the 5 or 6 button to select Advanced settings and press the 1 or 2 button to enter the sub menu as follows.

DCDi (Directional Correlational Deinterlacing) is used to process moving angled edge in deinterlacing to get the smoothest and most natural image. Press the 1 or 2 button on the remote control to select On or Off.

ACC/ACM (ACC: Adaptive Contrast and Color; ACM-II: Active Color Management-II) is used to select adaptive Brightness, Contrast and tone control. Press the 1 or 2 button on the remote control to select suitable mode either Vivid, Cinema, Sport or Off.

CCS (Cross Color Separation) is used to remove residual chroma information from luminance signal which is the result of imperfect decoding of composite video. Press the 1 or 2 button on the remote control to select either Auto, Standard or Off.

DNR (Digital Noise Reduction) is available for noise reduction. Press the 1 or 2 button on the remote control to select either Auto,

Low, Mid, High or Off.

MPEG NR (MPEG Noise Reduction): Removes unwanted ringing and

block noise from images that have undergone MPEG or JPEG compression and decompression. Press the 1 or 2 button on the remote control to select On or Off.

Film Mode (Inverse 3:2 pulldown): Film vs.Video-Detect ﬁlm. Performed on material which underwent technologic conversion to video. Press the 1 or 2 button on the remote control to select On or Off.

Sound menu

Press the MENU button and select Sound using the 5 or 6 buttons, press the 1 or 2 button to enter.

Select and adjust to obtain the best sound settings for your environment using the 5 or 6 button to select Treb le , Bass or Balance and the 1 or 2 button to adjust levels. Bass Expander can also be selected using the 5 or 6 button and pressing the 1 or 2 button to select On or Off. These settings automatically store when you exit the menu. Press the BACK button to return to the previous menu. Press the MENU button to exit menu operation.

Time menu

Press the MENU button and select Time using the 5 or 6 buttons, press the 1 or 2 button to enter. Press the BACK button

to return to the previous menu. Press the MENU button to exit menu operation.

n Current Weekday

Use to set current weekday using the 1 or 2 button.

n Current Time

Use to set the current time using the Numeric buttons.

✐ Other items in Time Menu should not be selected until Current

Time has been set.

n Schedule

Use to set up to 20 separate time schedules for “Power On” or “Power Off”, select 1 ~ 20 using the 1 or 2 button.

n Weekday

Use to set the schedule for “Power On” or “Power Off” of any weekday from Sunday through to Saturday or Everyday using the 1 or 2 button.

n Time

Use to set the schedule for “Power On” or “Power Off” of any time using the Numeric buttons.

n Action

Use to set the schedule for “Power On” or “Power Off” active using the 1 or 2 button. You can set Power On timer in Time menu selecting “ON” in “On Timer Function” in Installation Mode. If it is selected “OFF”, Power On display in Time menu does not functional.

n On Program

Use to select AV1, RGB, AV2 , AV3, PC, DVI or Network for the schedule of “Power On” using the 1 or 2 button.

n Active

Use to select ON or OFF using the 1 or 2 button. When set “OFF” the above items “Schedule”, “Weekday”, “Time”, “Action” or “ON Program” will be inactive. Use NUMERIC buttons [0 ~ 9] to set On Time. (Action “Power On” – 00:00 ~ 23:59)

✐ Once On Time has been set, when the set time is reached, the

monitor will leave the stand-by status and enter to the source automatically.

✐ After On Time has been set, you can go on watching other pro-

grams. When the set time is reached, the monitor will automatically switch to the preset program.

✐ On Program can only be selected whenAction (Power On) has

been set.

✐ Action (Power Off) can be set to turn the monitor into standby at a

selected time

Once On Program has been set, when the set time is reached, the monitor will enter to the preset source automatically. Use the 1 or 2 button to select On program, AV1, RGB, AV2, AV3, PC, DVI or Network.

Setup menu

Press the MENU button and select Setup using the 5 or 6 buttons, press the 1 or 2 button to enter. Press the BACK button to return to the previous menu. Press the MENU button to exit.

n Menu Setup

Whenever Setup menu is accessed initially, Menu Setup will be the default selection. Press the 1 or 2 button to enter the sub menu.

MENU OPERATION

GB GB

V_S ets is used to divide the vertical picture into more than one part,

and the most is also 5 parts (5 monitors). Using the 1 or 2

button to set.

H Location is used to select one part of the horizonal picture to display on the current LCD Monitor using the 1 or 2 button.

V Location is used to select one part of the vertical picture to display on the current LCD Monitor using the 1 or 2 button.

Language is used to select the preferred language. Use the 1 or 2 button to select English, French, German, Italian, Spanish or Dutch.

H-Position changes the OSD position horizontally by using the 1 or 2 button.

V-Position changes the OSD position vertically by using the 1 or 2 button.

Duration is used to set the display time of the MENU by using the 1 or 2 button. (5 ~ 120 seconds)

Transparence is used to adjust transparence of menu display. Use the 1 or 2 button to adjust levels.

n PIP/POP Setup

Use the 5 or 6 button to select PIP/POP Setup and press the 1 or 2 button to enter the sub menu.

Bezel H Adjustment is used to align the image horizontally with respect to the other monitors in the video wall to accomodate the bezel width using the 1 or 2 button. (0 ~ 10)

Bezel V Adjustment is used to align the image vertically with respect to the other monitors in the video wall to accomodate the bezel width using the 1 or 2 button. (0 ~ 10)

n AV2 Setting

Use the 5 or 6 button to select AV2 Setting and press the 1 or 2 button to select YPbPr or RGBHV. Connect your PC to either PC-IN or RGBHV on the rear of the set. Once connected select PC mode or AV2 (RGBHV, see page 5 for AV2 input settings) via the INPUT button on your remote control. The set will become a monitor for the PC.

n Native Resolution

Use the 5 or 6 button to select Native Resolution and press the 1 or 2 button to select XGA or WXGA 1366 x 768.

PIP/ POP Mode: Using the 1 or 2 button select the most suitable mode PIP1, PIP2, POP or Off. (Please refer to page 13.)

✐ When Mode is set to Off, Sub Source and PIP Position will not

work.

Main Source is used to select input source (AV1, RGB, AV2, AV3, PC, DVI or Network ) for main picture by using the 1 or 2 button.

Sub Source is used to select input source (AV1, AV2, AV3, PC or DVI) for sub picture by using the 1 or 2 button.

✐ For a combination of main picture and sub picture: only DVI or

Network input can assemble with other input source. For example, if main source is selected as AV1 input, then the sub source must be DVI or Network input.

PIP Position: Using the 1 or 2 button it can be selected Top Left, Top Right, Bottom Right or Bottom Left.

n Initial Settings

This function returns all setting values except for Installation Mode.

n Text Language

Use the 5 or 6 button to select Text Language and press the 1 or 2 button to select Western, Eastern, Russian, Arabic or

Farsi.

n Tile Mode

This function allows you to split an image to suit your monitor grid format to create a video wall. Use the 5 or 6 button to select Tile Mode and press the 1 or

2 button to enter the sub menu as follows. Tile Mode Active can be set On or Off using the 1 or 2 button.

n PC Power Save

The monitor set automatically turns off with no PC input signal and wakes up with signal while PC Power Save is active. Use the 5 or 6 button to select PC Power Save and press the 1 or 2 button to select ON or OFF.

PC Adj. menu

Press the MENU button and select PC Adj. using the 5 or 6 buttons, press the 1 or 2 button to enter. Press the BACK button

to return to the previous menu. Press the MENU button to exit menu operation.

Auto Adjust is used to automatically detect incoming signal, and adjust itself to optimize its performance by using the 1 or 2 button. If the image is not displayed properly, a manual adjustment is required (Refer to following adjustments).

H-Position is used to move the horizontal picture position by using the 1 or 2 button.

V-Position is used to move the vertical picture position by using the

1 or 2 button. Clock is used to eliminate ﬂicker from the image by using the 1 or

2 button. Phase is used to eliminate disorder from the image by using the 1

or 2 button.

H_Sets is used to divide the horizonal picture into more than one

part, but the most is 5 parts (5 monitors).

Installation Mode

On program

Tuner Menu

Max Volume Winter mode RC inhibition Child Lock Address Baud rate Panel protection AV Auto shut off Network Standby On Timer Function LED light setting

DCR

Network initial Temperature Error IP Address Subnet Gateway DNS

Off

63 Off Off Off

19200

Off Off On Off Off

Off

>>>

000000000000

G2.02 0000

Select Adjust

Exit

GB GB

INSTALLATION MODE

Installation Mode

This LCD monitor allows you to set up the following :

SETTING PROCEDURE

1. Press and hold the GREEN button on the remote control for 5

seconds. (Installation Mode will appear)

2. Use the 5 or 6 button to highlight each option, use the 1 or 2 button to adjust each option. Press the MENU button to exit

the mode.

n Address

Set the address for the LCD monitor (0 ~ 999).

¡ Setting the monitor address in RS232 mode

Each monitor can have a speciﬁc Address, which helps command that monitor individually and will not effect to other monitors connected to a controlling PC Address format command. The addressing format command is used for operating multiple monitor sets from a single PC via the RS232C command line.

n Baud rate

Select Baud rate using the 5 or 6 button. To set transmission speed RS232 or LD-NET communication for 19200 or 9600 Baud rate by pressing the 1 or 2 button.

n Panel protection

To prevent image sticking which may occur showing still picture for a long time, select “Panel Protect” using the 5 or 6 button, once highlighted you can select ON or OFF by pressing the 1 or 2 button.

n AV Auto shut off

With no picture input signal to AV1, RGB, AV2(YPbPr), AV3, DVI, Network, set turns off automatically. Select “AV Auto Shut Off” using the 5 or 6 button, once highlighted you can select On or Off by pressing the 1 or 2 button.

n Network Standby

You can save power consumption selecting “Off” at Network Standby in Installation mode, both RS232C and LD-NET do not functional. To make them functional, select “ON” in this menu.

n On Program

Select ON program using the 5 or 6 button, select the start up position using the 1 or 2 buttons. (Off/AV1/RGB/AV2/AV3/PC/DVI or Network)

n Max Volume

Select Max volume using the 5 or 6 button, use the 1 or 2 buttons to set the maximum volume required.

n Winter mode

This Function can be activated when the LCD monitor is used during cold temperature conditions, approximately 38˚F/4˚C or below to maintain picture performance. Using the 5 or 6 button select winter mode, once highlighted you can select ON or OFF by pressing the 1 or 2 button. IMPORTANT: The AC cord should not be disconnected during the operation of Winter mode function. When in winter mode, power consumption is higher than normal standby consumption. This is entirely due to the operation of heating circuitry. We strongly recommend to turn off Winter mode when the ambient temperature is above 38˚F/4˚C.

n RC inhibition

You can prevent unwanted remote control operation by selecting RC Inhibition. Select using the 5 or 6 button. Press the 1 or 2 button to select On or Off. To re-instate RC operation press and hold the green button on the remote control and select RC inhibition OFF.

n Child Lock

You can prevent unwanted operation of the LCD monitor via the buttons on the rear of the monitor. Select using the 5 or 6 button. Press the 1 button to select On or OFF. The “Child Lock” OSD will appear if buttons are pressed when child lock is On.

✐ Standby operates normally when childlock is set “On”.

n On Timer Function

You can save power consumption selecting “Off” at On Timer function in Installation mode. On Timer in Time menu does not functional. To make them functional, select “ON” in this menu.

n LED Light setting

Select LED Light setting using the 5 or 6 button, once highlighted you can select On or Off by pressing the 1 or 2 button.

n DCR

The picture contrast improved while DCR is ON. Select DCR using the 5 or 6 button, once highlighted you can select On or Off by pressing the 1 or 2 button.

n Network Initial

This function automatically installs the IP Address, Subnet, Gateway and DNS information.

n Temperature Error

The recorded number of abnormal temperature is occurred is indicated here.

n IP Address /Subnet /Gateway/DNS

These 4 items display the LD-Net information. If LD-NET is NOT connected, all the items would be displayed as “000000000000”.

✐ Disconnecting the mains supply before exiting Installation Mode

will cancel the following features On program, RC inhibition, Address and Baud Rate.

TITLES ON SCREEN

GB GB

OPER ATION

Selection of picture size

Select screen size from FULL, FULL ALL, ZOOM 16:9, TITLE IN 16:9, ZOOM 14:9, TITLE IN 14:9, NORMAL or NATURAL WIDE by pressing the WIDE button repeatedly on the Remote Control.

✐ When in AV2 (RGBHV) or PC mode FULL or NORMAL can be

selected.

Note: Full - Set display area 100%

✐ Only in DVI or AV2 (YPbPr) displaying high resolution content

FULL and FULL ALL are selectable.

Note: FULL - Set display area 95%

FULL ALL - Set display area 100%

All other inputs AV1, AV3, DVI or AV2 (YPbPr) (displaying lower resolutions) can select all picture sizes.

n Full/Full All