Sanyo CE30LD3BK-B Instruction Manual

Download

30LD3BK-B

Please read this Instruction book before using your television.

We wish you many hours of pleasure from your new television.

Colour Television

INSTRUCTION MANUAL

The product (meaning the equipment or appliance to which this documentation relates) incorporates Software (the software applications, utilities and modules embedded within the Product) which is owned by Sanyo or its licensors. Before using the product, please read the End-User Licence Conditions detailed below. If you do not agree to the terms and conditions of the End-User Licence, Please do not proceed to use the Product- repack the Product unused and return it to your supplier together with proof of purchase for a full refund. By using the product, you agree to be bound by the terms and conditions of the End-User Licence.

Licence Grant, Conditions and restrictions

Sanyo grants you a non-exclusive, world-wide (subject to export controls), non-transferable (except as permitted by 2 below), royalty-free licence to use the Software upon and with the Product.

You may not transfer any of your licence rights in the Software without the prior written consent of SANYO and if consent is provided then the Software shall only be transferred in conjunction with the transfer of the Product AND provided that the transferee has read and agreed to accept the terms and conditions of this licence.

You must ensure that the copyright, trademark and other protective notices contained in the Software are maintained and not altered or removed.

The Software provided hereunder is copyrighted and licenced (not sold). SANYO especially does not transfer title or and ownership rights in the Software to you. The Software provided hereunder may contain or be derived from portions of materials provided to SANYO under licence by a third party supplier.

Except as expressly permitted by statute

you may not;

●

use the Software in conjunction with any other computer hardware other than the product;

●

copy all or part of the Software;

●

incorporate all (or any of) the Software into other programs developed by (or on behalf of) you and/or used by you;

●

reverse-engineer, decompile or disassemble the Software;

●

make the Software (or any part of it) available, or permit its redistribution, for use with any computer hardware other than the Product; or rent, lease, gift, loan, sell, distribute or transfer possession of the whole or any part of the Software.

Termination

This licence is effective until terminated. This licence will terminate automatically without notice if you fail to comply with any of its p r o v i s i o n s .

Disclaimer

The Software is(to the extent permitted by law) supplied ‘as is’ and SANYO and its suppliers expressly exclude all warranties, express or implied, including (but not limited to) warranties of satisfactory quality, fitness for purpose and non-infringement (save to the extent that the same are not capable of exclusion at law).

2. In no circumstances will SANYO be liable for any direct, indirect,

consequential, or incidental damage (including loss of profits, business interruption, loss of data or the cost of procurement of substitute goods, technology or services) arising out of the use or the inability to use the Software (save to the extent that such liability is not capable of exclusion at law).

General

This End-User Licence will be governed by laws of England and the User may only bring claims in the English Courts and SANYO shall be entitled to bring a claim in the courts of any jurisdiction.

The above terms and conditions supersede any prior agreement, oral or written, between you and SANYO relating to the Software.

End-User Licence

Your television is fully transistorised and does not contain any user serviceable components.

You must not remove the rear cover of the TV by yourself. The apparatus is working with high voltages and could damage objects or even endanger people. Leave all required repair and service jobs to an authorised service technician. He will exclusively use such spare parts that are complying with the same safety standards as applicable to the original parts. The use of original spare parts can prevent fire, shock and other hazards.

Unplug the television receiver from the wall outlet and refer servicing to qualified service personnel under the following conditions:

■

If the power cord or plug is damaged.

■

If liquid has been spilt into the television receiver.

■

If television receiver has been exposed to rain or water.

■

If the television receiver has been dropped or the cabinet has been damaged.

■

If the television receiver exhibits a distinct change in performance.

■

If the television receiver does not operate normally by following the operating instructions.

Adjust only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage. This will often require extensive work by a qualified technician to restore the television receiver to normal operation.

Servicing

Do not allow anything to rest on the power

cord. Do not locate this television receiver where the cord will be damaged by people walking on it.

Do not overload wall outlets and extension cords as this can result in fire or electric shock.

Slots and openings in the cabinet and in the back or bottom are provided for ventilation to ensure reliable operation and to protect it from overheating. These openings must not be blocked or covered. The opening should never be covered with a cloth or other material, and the bottom openings should not be blocked by placing the television receiver on a bed, sofa, rug, or other similar surface.

Do not place this television near any heat sources such as radiators, heaters, stoves and other heat-generating products (including amplifiers).

Do not place the television in direct sunlight.

Do not place your television receiver on an unstable stand, shelf

or table. Serious injury to an individual, and damage to the television may result if it should fall. Your sales person can recommend approved stands or shelf and wall mounting instructions. A special wall mounting kit is available for this model.

If the television is built into a unit, or enclosed, the minimum distances for ventilation must be maintained. Heat build up can reduce the life of your television, and can be dangerous.

This television receiver should be operated only from the type of power source indicated on the television or as indicated in the Operating Instructions. If you are not sure of the type of power supply in your home, consult your sales person or your local power company.

Never add accessories that have not been specifically designed for this television.

Do not drop or push objects into the television cabinet slots or openings. Some internal parts carry hazardous voltages and contact may result in an electric shock hazard. Never spill liquids of any kind on the television receiver. Do not place items such as vases containing liquid on top of the TV set.

Do not expose the television receiver to rain or use near water. For example, near a bathtub, kitchen sink, in a wet basement, etc. Do not use immediately after moving the television from a low temperature to a high temperature environment, as this causes condensation, which may result in fire, electric shock, or other hazards. Before cleaning, unplug the television receiver from the wall socket.

Never stand on, lean on or push the television or its stand. Never allow children to play with the television or its stand. Serious injury may result if it should fall.

Do not apply liquid cleaners or aerosol cleaners directly onto the television receiver. Use a soft cloth for cleaning.

Do not place candles or hot objects upon the TV, next to it or behind it. Open flames must never be used near the TV set.

Installation

CAUTION: Please read and retain for your safety. This unit has been engineered and manufactured to assure your personal safety, but

improper use can result in potential electric shock or fire hazards. In order not to defeat the safeguards incorporated in this receiver observe the following basic rules for its installation, use and servicing.

Use

●

Cleaning your LCD screen.

Your LCD screen is coated in a non reflective film. Damage to this film will result in possible discolouration. Any scratches will not be repairable.

Clean your screen with a soft cloth, only rub lightly, do not use detergents.

Do not stick anything to the screen, use solvent or alcohol based cleaners, hit the screen with a hard object or rub the surface hard.

●

Placement of your LCD TV.

Table topstand

This LCD TV is supplied with a table top stand fitted. This stand can rotate 36˚ to the left or right. To rotate your TV hold the base and gently push the edge of the TV.

Display stand

An optional stand is available for your LCD TV and other equipment. You will have to remove the table top stand to use this.

Wall mounting bracket

An optional wall bracket is available for your LCD TV. Before you consider wall mounting this TV, check that you have an appropriate wall made from solid materials such as concrete or bricks. You will have to remove the table top stand to use this.

Important:

THIS PRODUCT MUST BE EARTHED

This equipment is fitted with an approved non rewireable UK mains plug. To change a fuse in this type of plug proceed as follows:

1. Remove the fuse cover and fuse.

2. Fit a new fuse which should be a BS1362 13Amp A.S.T.A. or BSI approved type.

3. Ensure that the fuse cover is correctly refitted.

If the fuse cover is lost or damaged the plug must NOT be used but replaced with a serviceable plug. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a rating of 13 Amp, ensure the fuse cover is correctly fitted. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 13 Amp.

Note:

The severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13Amp socket elsewhere.

The wires in this mains lead are coloured in accordance with the following code:

Blue -------> Neutral Brown ----> Live Green and Yellow ----> Earth

1. The Blue wire must be connected to the terminal which is marked with the letter “N” or coloured BLACK.

2. The Brown wire must be connected to the terminal with the letter “L” or coloured RED.

3. The Green and Yellow wire must be connected to the terminal which is marked with the letter “E” or coloured GREEN or GREEN and YEL-

LOW.

Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the wires.

Do not attempt to bypass the safety purpose of the grounding type plug.

THIS UNIT IS NOT DISCONNECTED FROM THE MAINS UNLESS THE MAINS LEAD IS UNPLUGGED.

Care of your product

1. Connect your aerial cable socket to the back of the TV set. Fit the

aerial cable either as shown, or as shown in the diagram below when AV equipment is connected.

●

Connecting DVD / VCR player/

Satellite receiver or

Set top box.

We recommend that you connect all other equipment before Plug and Play. The following examples are our recommended standard connection. For further information please consult your local dealer.

2. Connect the 3 pin connector to the LCD TV set.

3. Connect the power cord of the LCD TV to a wall outlet.

✐

The TV set is prepared for a mains voltage AC220~240V, 50Hz. To disconnect completely from the mains or, when the TV set is not to be used for an extended period of time, it is advisable to disconnect the power cord from the power outlet or the 3 pin connector at the back of the TV.

✐

For all aerial problems please consult your local dealer.

Install two "AA" 1.5 volt batteries so that the "+" and "-" marks on the batteries match the "+" and "-" marks inside the unit into the remote control handset.

Step : 1 Connections ( Essential)

WARNING! High voltages are used in the operation of

this set. Refer service to qualified service personnel.

Step : 2

Remote control battery installation

The LCD TV will have a red Standby light to show there is power. Press the standby button to start Plug and Play.

The self-automatic tuning system called Plug and Play will start. The TV scans the analogue channels first and then switches to digital channel mode and scans digital channels. This could take up to 15 minutes. During automatic tuning, the TV displays the tuning status of analogue and digital channel tuning on the screen.

Press the OK button (on remote control only) to save.

Press the OK button (on remote control only) to Watch TV.

Now the installation is completed!

After Plug & Play, Digital channels are stored in the programme positions shown in the All channel table. Analogue channels will be automatically sorted as follows:

Programme position 1 : BBC1 Programme position 2 : BBC2 Programme position 3 : ITV Programme position 4 : CH4 or S4C Programme position 5 : CH5 Programme position 6 : ITV2 Programme position 7 : channels in order found.

✐

If any other channels are available in your reception area, the remaining channels will be stored from programme position 7 in sequence as found.

✐

If you move to another city or cable is installed, please follow the description “Channel List - scan for channels”. (on page 11) or “Preset Menu” (on page 16) for Analogue channels.

✐

This procedure only appears the first time you switch on.

1. Front of LCD TV

Standby switch

Standby Power indicator.

Timer indicator.

ECO indicator.

Light monitoring sensor.

Remote control sensor.

2. Right side terminals

Press the 5 or 6 button to increase or decrease the programme position.

Press the 1 or 2 button to increase or decrease the sound volume.

OK: This button has no function in Digital

mode. In analogue mode use to save menu settings.

MENU: This button has no function in digital

mode. In analogue mode it accesses the menu function.

3. Left side terminals

✐

To select the AV3 mode press the v button repeatedly.

✐

When the headphones are inserted the sound from the TV speakers is muted.

3.5 mm Mini Headphone din

AV3 Video in

AV3 Left Audio in

AV3 Right Audio in

Step : 3 Switching on / Plug & Play

Controls / Terminals

The main menu screen takes you to many functions in the TV. The buttons below are the main buttons and their uses.

MENU button - Enters and exits menus.

Button e and d moves up and down in

each selected menu.

Button 7 changes levels, moves to the left and returns to previous menu.

Button 8 changes levels, moves to the right and enters next menu.

RETURN button - Returns to the previous screen.

Refer to bar at bottom of screen for added help in which buttons to use.

Press the 7 or 8 button and select Picture menu, set the picture settings for your personal preference.

Use the e or d button to select eg. Brightness and the 7 or 8 but- ton to adjust levels.

Eco : This function can reduce the power consumption by control-

ling the amount of backlight.

Use the e or d button to select and the 7 or 8 button to set.

To memorise these settings press the F/OK button. (The OK? will change to OK.)

To exit press the MENU button.

Press the MENU button and select Sound menu by pressing the 7 or 8 button.

Select and adjust to obtain the best sound settings for your environment using the e or d and 7 or 8 buttons.

Press the MENU button to return to Main Menu. These settings automatically store when you exit the menu.

Press the MENU button repeatedly to exit menu.

You can set up different user lists to allow quick access to your favourite channels.

■

Setting User Lists

1. Press the MENU button to select

main menu.

2. Select User Lists by pressing the

d button.

3. Select Your TV lists menu by

pressing the 8 button.

4. Select a List eg. List 1 by pressing

the e or d button. Enter by pressing the 8 button.

5. Press the 8 button to add channels to your list. Use the e or d button to highlight channel selection. Press the OK button to add to your list, a X will appear next to the channel.

6. Repeat to add all the channels you want in your list.

7. Press the Blue button to save selection.

8. Add more channels, move selection, rename list, remove or swap or press the OK button to finish the list or the MENU button to exit.

■

Move selection.

To change the order of channels in your list.

1. Select the channel you wish to move using the e or d button.

2. Press the Green button to select the channel.

3. Use the e or d button to move to a different position

4. Press the Green button to save the new order.

Repeat steps 1-4 until all channels are in the order you need.

5. Add more channels, move selection, rename list, remove or swap or press the OK button to finish the list or MENU to exit.

■

Rename List.

1. Press the Blue button to rename your list. see picture.

2. Use the 7 or 8 button to move left or right.

3. Use the e or d button to choose a letter, symbol or number. (A-

Z, 0-9, -,+ etc.)

4. Press the OK button to save new user list name.

5. Add more channels, move selection, rename list, remove or swap

or press the OK button to finish the list or the MENU button to exit.

Picture menu

Sound menu

User Lists

Main menu

■

Remove a channel.

1. Highlight a channel to be removed.

2. Press the Red button and it will be deleted, the screen shows a red line through it. To deselect a deleted channel press the Red button again.

✐

Red button refers to coloured buttons Red, Green, Yellow and Blue. Do not get confused with larger Red Standby button.

3. Add more channels, move selection, rename list, remove or swap or press the OK button to finish the list or the MENU button to exit.

■

Swap channels.

1. Choose a channel that you wish to swap with another by pressing

the e or d button . Press the Yellow button to enter the Swap screen.

2. Use the 7 , 8 buttons and numeric buttons to enter channel number and press the OK button to swap.( When in swap screen you can press the RETURN button repeatedly to take you back a screen).

3. Add more channels, move selection, rename list, remove or swap or press the OK button to finish the list or the MENU button to exit.

4. Press the MENU button to return to normal picture.

When watching a digital channel. Press the 8 button. A title bar appears at the bottom of the screen with each press of the 8 button

it will select All channels and all your set user lists. Use the e or d button to browse through the list, the TV will switch to this channel. ( Only channels in the selected list will be browsed).

Parental lock can be used to block entry into the Menu functions and to allow you to block access to selected channels.

The first time you use this function the code numbers are 1 2 3 4. If you forget the code there is a default code 6 9 3 1 this will always give you access to Parental lock.

●

How to change the code to your own preference.

1. Press the MENU button to select Main Menu.

2. Using the e or d button select Configuration and press the 8

button to enter.

3. Press the d button to select Change parental code. Press the 8 button to enter.

4. Enter Old code into yellow box which is highlighted, using the 0-9 numeric buttons (If this is the first time you have selected this function it will be 1 2 3 4). Use the 7 button to go back and reenter an incorrect digit.

5. Select New code by pressing the d button, and enter your new

code eg. 4 3 2 1.

6. Select Confirm new code by pressing the d button, and re-enter

the code 4 3 2 1.

7. If you are happy with the new code press the OK button to select. A prompt Save new code? will appear. Press the Red button to confirm.

✐

If Invalid code! appears you have entered the incorrect old code. Press the RETURN button and try again.

Press the MENU button to return to normal picture.

●

To activate parental lock.

1. Press the MENU button to select Main menu.

2. Using the e or d button select Parental lock. Press the 8 button to enter.

3. Enter your code and press the OK button to save. If wrong code

is entered Invalid code! will appear and you have to repeat 1-3 again.

✐

Parental lock is now activated you will now have to enter the code every time before you can enter Main menu unless parental lock is deactivated. See page 8.

●

Blocking access to selected channels.

1. Press the MENU button to select Main menu.

2. Using the e or d button select Channel List. Press the 8 button to enter.

3. Select Lock channels using the e or d button. Press the 8 button to enter.

4. Using the e or d button select a Channel you wish to lock.

5. Press the Yellow button, a locked symbol will appear to show it is

selected. To de-select press the Yellow button again. Repeat until all channels you wish to lock are selected.

6. Press the OK button to Save.

This takes you back to Channel List Menu.

To return to normal picture press the MENU button.

Using User Lists

Parental lock

●

How to watch a locked channel.

1. Select a locked channel, Parental lock display appears.

2. Press the OK button, enter the Parental code and press the OK button again.

3. The channel is temporarily unlocked until the channel is changed.

4. Press the MENU button to return to normal TV picture.

✐

If Parental lock is activated and you wish to record this locked channel, deactivate first before setting timer recording.

●

To deactivate parental lock.

1. Press the MENU button to select Main menu.

2. Enter the Parental code.

3. Press the OK button to enter menu functions.

4. Use the e or d button to select Parental unlock, press the 8 button to enter.

5. Press the Red button to deactivate.

6. Press the MENU button to exit.

✐

Main menu screen will show either Parental Lock or Parental Unlock ( if it is use).

✐

Once you have activated Parental Lock each time you need to enter the Main Menu you will need the code.

●

Preferred language.

1. Press the MENU button to select Main Menu.

2. Select Configuration by using the e or d button. Press the 8 button to enter.

3. Press the d button to highlight Preferred language and press the 8 button to enter.

Audio - Select your preferences as required.

Example. If you speak Welsh (Gaelic) and prefer to receive Welsh (Gaelic) audio when it is transmitted then select Welsh (Gaelic) for your first Language and English as your second.

4. Press the 7 or 8 button to select Language, press e or d button select second language and change your preference using the 7 or 8 button.

Subtitling - Select your preferences as required.

If you wish for Welsh or Gaelic Subtitles instead of English to be shown (when available) then select your preference for the first language.

Example: as shown will give you English first language, if not available Welsh may be shown.

5. To change press the e or d button to highlight the box and press the 7 or 8 button to select your preferred First language and repeat for Second language.

6. Press the d button to select Subtitle display. This can be set ON or OFF by pressing 7 or 8 button.

7. Press the OK button to Save.

This takes you back to Configuration menu screen.

Change Parental Code - See page 9 under Parental lock.

Press the MENU button to return to normal TV Picture.

●

Common Interface

This TV set provides a common Interface slot on the rear of the TV set.

1. On the table top stand, swivel it fully to the left.

2. Insert the card in the slot located on the underside next to the

aerial.

3. Press the MENU button to select Main Menu.

4. Select Configuration by using the e or d button. Press the 8 button to enter.

5. Press the d button to highlight Common Interface and press the

8 button to enter.

The following screen appears to show that a card is inserted. When you select OK, follow the on screen directions. This will vary depending on the type of card inserted.

Important!

The TV should be turned off by the Standby button when inserting or removing the Common Interface Card, otherwise it may cause damage to the card or the TV set.

Parental lock

Configuration

●

Edit channel list

1. Press the MENU button to select Main Menu.

2. Select Channel List by using the e or d button. Press the 8

button to enter.

3. Select Lock channels by using the e or d button. Press the 8

button to enter.

4. To delete channels from this list use the e or d button to high-

light a channel.

5. To lock or unlock parental locked channels, select the channel and press the yellow button. This will lock or unlock the channel.

6. Press the OK button, selected channels will be locked / unlocked and parental lock/unlock stored.

You will go back to Channel List menu.

●

Scan for channels

1. Press MENU button to select Main Menu.

2. Select Channel List by using the e or d button.

3. Press the d button to select Scan for channels. Press the 8

button to enter.

This will scan all available channels. This is a useful function if you delete channels and want to get them back later.

4. Press the OK button to save (All Channels).

5. Press the OK button again to watch normal TV picture.

✐

Parental lock is still saved after the scan for channels has been initialised.

In this section a lot of the information will only be useful to a technician. Some parts are however useful to you. If there is an upgrade in software you will need this section to upgrade your TV from time to time.

1. Press the MENU button to select Main Menu.

2. Select Technical Information menu by using the e or d button. Press the 8 button to enter.

3. Select Signal information by using the e or d button and press

the 8 button to enter.

This screen cannot be altered but if you have a problem you may need to refer to this screen for some data.

4. Press the Return or OK button to go back to Technical information screen.

■

Software upgrade

1. Press the d button to select Software Upgrade screen. Press

the 8 button to enter.

This looks for any new software upgrades that maybe transmitted at any time.

2. Press the Return button to go back to Technical information screen.

3. Select Product Data by using the e or d button and press the 8 button to enter.

This is useful to service engineers.

4. Press the Return button to go back to Technical information screen.

5. Press the d button to select Reset screen. Press the 8 button to enter.

If you press Red button to confirm it will return all settings to factory (default) mode for digital channels. To start a scan for all available channels switch the TV set Off and On again and press D/A button to select digital.

When the TV set has been initialised press the OK button to Save and the OK button to watch TV picture.

Channel List

Technical Information

- This feature is used when you wish to record a digital channel on your VCR.

- In order to record digital channels you cannot watch another digital channel when recording. Digital channels are recorded using AV2.

- Timer recording will switch your TV set to the digital channel at the preset time until the finish time is reached.

- Whilst timer recording is running you can switch to Analogue TV.

- You can also switch your TV into Standby mode, the timer recording will switch your TV on and off back into Standby when finished.

✐

If you want to switch to another digital channel you must first cancel recording by pressing the Return button.

✐

If channel has been locked (Parental lock) and you have set timer record for locked channel it will not record. You have to deactivate parental lock first.

1. Press the Menu button to select Main Menu.

2. Select Timer recording menu by using the e or d button. Press

the 8 button to enter.

3. Highlight a row and press the OK button. Set events screen

appears.

4. Select channel by pressing the 7 or 8 button and rotate through

all available channels.

5. Press the d button to select and highlight yellow Wake-up day

box. Enter your day, month and year by using numeric buttons (0-

9). and using the 7 or 8 button to move left and right.

6. Press the d button to select and highlight yellow Wake-up time

box. Enter your time by using numeric buttons (0-9). and using the

7 or 8 button to move left and right.

7. Press the d button to select and highlight yellow Finish time box.

Enter your time by using numeric buttons (0-9). and using the 7 or 8 button to move left and right the time you wish to finish.

8. Press the d button to select and highlight yellow Repeat box.

Press the 7 or 8 button to enter No repeat, daily, or weekly. This would be a useful feature if you have a favourite programme that you dont want to miss and it is shown on a daily or weekly schedule.

9. Press the OK button to save settings, you can repeat again or

press the RETURN button to go back to Main menu. Press the MENU button to exit.

Once you have set the timer recording, 5 minutes before the selected time the following screen appears.

You can either press the Red button and delete, press the Green

button and the channel will change at the due time, press the Yellow button to change to the channel now or press the Blue button to

cancel settings.

✐

If you want to switch to another digital channel you must first cancel recording by pressing the Return button.

■

Off-timer setting

The Off timer will switch the TV set into the standby mode when the selected time has elapsed.

1. Press the MENU button and select Main Menu.

2. Press the d button and select Off Timer. Press 8 to enter.

3. Select Timer using the 7 or 8 button. Select OFF Timer using the e or d button. The complete line turns yellow.

4. Press the 7 or 8 button to select --:-- (highlighted yellow).

5. Press the e or d button to change time.

The time changes in 30 minute steps.The maximum time is 2:00hrs.

6. Press the 7 or 8 button to highlight complete line (yellow).

7. Press the OK button to store your settings.

If you have set the off timer, then one minute before the TV switches off, a display appears on the screen.

✐

If the TV set is switched off by the standby button on the remote control or by the standby switch on the front of the TV set the timer settings will be cancelled.

Press the MENU button to exit, or press 7 to highlight complete line yellow and then Press the d button to set Alarm timer.

■

Alarm timer setting

This function can be set so that an alarm goes off. This only happens when the TV is switched on. It may remind you to do something.

1. Press the MENU button and select Main Menu.

2. Press the d button and select Off Timer. Press 8 to enter.

3. Select Timer using the 7 or 8 button. Select Alarm Timer using the e or d button. The complete line turns yellow.

4. Press the 7 or 8 button to select --:--.

5. Press the e or d button to change time.

The display changes in 5 minute steps and the maximum time period is 3:00 hours.

6. Press the 7 or 8 button to highlight complete line (yellow).

7. Press the OK button to set the Alarm.

8. Press the MENU button repeatedly to return to normal TV picture.

When the time period is up, the time up signal will appear on the screen and the alarm will sound for 15 seconds.

To cancel the Alarm timer press any button and the display will disappear.

✐

If the TV set is switched off by the standby switch on the remote control, the standby switch on the front of the TV or a power fail ure occurs the timer settings will be cancelled.

Timer recording

Timer menu

■

Child lock

You can prevent small children from operating the TV with the side buttons on the TV set.

1. Press the MENU button and select Main Menu.

2. Press the d button and select TV Setting menu. Press the 8

button to enter.

3. Select Setting using 7 or 8 button and Child lock using the e or d button.

4. Set the Child lock to OFF or ON by pressing the 7 or 8 button.

✐

The child lock mode will be reset to “OFF” when the TV set is completely disconnected from the Mains supply.

■

AV2 setting

In setting menu, to select AV2 press d and set to Video or S-Video depending on your external equipment. If you use a VCR which has S-VHS, you should connect it to AV2 and change the AV2 menu to SVIDEO.

1. Press the 7 or 8 button to select either Video or S-Video.

2. Press the MENU button to exit, this automatically stores your

changes.

Press the MENU button or RETURN button twice to return to normal TV picture.

■

Light Monitoring

This function automatically adjusts the picture level (eg. brightness, contrast) depending on the brightness of your surroundings.

1. In Setting menu press the e or d button and select Light monitoring.

2. Press the 7 or 8 button to select ON or OFF.

Press the MENU button or RETURN button repeatedly to return to normal TV picture.

The guide shows the digital TV schedule for the next 2 hours.

The guide can show all channels or any set user lists ( see page 8). Press the 8 button to select all channels or a user list then press

GUIDE button.

A schedule will appear on the screen.

Use the e or d button to move up and down the channel list. Use 7 or 8 button to highlight the programmes below the transmission time, progress and a brief programme explanation will be displayed.

Press the Guide button to return to normal picture.

Press the button to get more information on that programme.

When you press the info button in digital mode you will be displayed a cut down guide showing only the channel you are currently on.

Press the 7 or 8 button to select current programme or next.

Press the GUIDE button to go to the full guide. Press the 5 or 6 button to change to the channel.

From time to time upgrades will become available. When this happens the following screen appears.

To upgrade press the OK button and the following screen will appear.

Press the OK button to start, this automatically downloads for you. The following screen appears.

The following screen appears to show that the upgrade it nearly finished. Once this screen disappears the upgrade is complete.

Guide

Info buttonTV Setting menu

Programme Download

Once you have started the upgrade process you must not interrupt it (disconnect or separate it from the mains supply) under any circumstances. Do not press any key on the remote control or the front of the cabinet. If you interrupt the upgrade process the IDTV may be defective afterwards.

■

VCR / DVD controls

With selected Sanyo DVD/VCR players you can use this remote. The following table shows all available function buttons for the VCR and DVD. When you use a compatible Sanyo DVD player, first press and hold the DVD button and then press your desired function button.

Many of your T V ’ s functions are controlled through the menu function.

During menu operation a bar at the bottom of the screen show which controls can be used.

Press the MENU button to enter and exit the 5 sub menus Picture, Sound, Timer, Setting and Preset.

When a sub menu is selected its options are displayed and its colour will change to yellow.

When you have set each Sub menu you can either press MENU to exit and clear the screen or press the 5 button until the sub menu is re-selected. Using the 7 or 8 button you can rotate again.

Press the 7 or 8 button and select Picture menu, set the picture settings for your personal preference.

Use the e or d button to select eg. Brightness and the 7 or 8

button to adjust levels.

Tint : is only available if NTSC equipment is connected.

Eco : This function can reduce the power consumption by controlling

the amount of backlight.

Text bright : you can set to minimum, centre or maximum.

Use the e or d button to select and the 7 or 8 button to set.

To memorise these settings press the OK button. (The OK? will change to OK.)

To exit press the MENU button.

Press the MENU button and select Sound menu by pressing the 7 or 8 button.

Select and adjust to obtain the best sound settings for your environment using the e or d and 7 or 8 buttons.

To exit press the MENU button.

■

Off-timer setting

The Off timer will switch the TV set into the standby mode when the selected time has elapsed.

1. Press the MENU button and select Timer using the 7 or 8 button. Select OFF Timer using the e or d button. The complete

line turns yellow.

2. Press the 7 or 8 button to select --:-- (highlighted yellow).

3. Press the e or d button to change time.

The time changes in 30 minute steps.The maximum time is 2:00hrs.

4. Press the 7 or 8 button to highlight complete line (yellow).

5. Press the OKbutton to store your settings.

If you have set the off timer, then one minute before the TV switches off, a display appears on the screen.

✐

If the TV set is switched off by the standby button on the remote control or by the standby switch on the front of the TV set the timer settings will be cancelled.

Press the MENU button to exit, or press the 7 button to highlight complete line yellow and then press the d button to set Alarm timer.

■

Alarm timer setting

This function can be set so that an alarm goes off. This only happens when the TV is switched on. It may remind you to do something.

Press the MENU button and select Timer using the 7 or 8 button. Select Alarm timer using the e or d button. The complete

line turns yellow.

Press the 7 or 8 button to select --:--.

3. Press the e or d button to change time.

The display changes in 5 minute steps and the maximum time period is 3:00 hours.

4. Press the 7 or 8 button to highlight complete line (yellow).

5. Press the OK button to set the Alarm.

When the time period is up, the time up signal will appear on the screen and the alarm will sound for 15 seconds.

To cancel the Alarm timer press any button and the display will disappear.

✐

If the TV set is switched off by the standby switch on the remote control, the standby switch on the front of the TV or a power failure occurs the timer settings will be cancelled.

Picture menu

Sound menu

Timer menu

■

Child lock

You can prevent small children from operating the TV with the side buttons on the TV set.

1. Press the MENU button and select Setting using the 7 or 8 button and Child lock using the e or d button.

2. Set the Child lock to OFF or ON by pressing the 7 or 8 button.

✐

The child lock mode will be reset to “OFF” when the TV set is completely disconnected from the Mains supply.

■

Noise Reduction

1. Press the MENU button and select Setting using the 7 or 8 but- ton and Noise Reduction using the e or d button.

2. Set to Min, Med, Max or OFF by pressing the 7 or 8 button.

3. Press the MENU button repeatedly to return to normal TV picture.

■

AV2 setting

1. Press the 7 or 8 button to select.

2. Press the MENU button to exit, this automatically stores your

changes.

■

Light Monitoring

This function automatically adjusts the picture level (eg. brightness, contrast) depending on the brightness of your surroundings.

1. In Setting menu press the e or d button and select Light monitoring.

2. Press the 7 or 8 button to select ON or OFF.

Press the MENU button or RETURN button repeatedly to return to normal TV picture.

The preset menu can be used to tune new channels, to reorder channels and their programme positions, and to make fine adjustments to the tuning.

■

Auto Tuning

1. Press the MENU button and select Preset using the 7 or 8 button. Select Auto Tuning using the e or d button. The

complete line turns yellow.

2. Press the 8 button and select Auto.

3. Press the 8 button to start, all available channels are automatical-

ly stored, starting from programme position 01.

After completing this procedure, the TV set returns to programme position “01”.

Position changes sequentially as channels are found.

To cancel this tuning operation, press the MENU button r e p e a t e d l y.

✐

You can change the order of the station selection, by using the channel swapping function detailed later.

■

Auto Sort

1. Press the MENU button.

2. Select Preset, press the e or d button select Auto sort and press the 8 button.

3. Press the OK button to start automatic sorting and storing of TV

stations in your area. It will sort the channels as in Plug and Play (See page 6).

To cancel press the Menu button repeatedly.

■

Prog. preset.

This is used to preset a received channel in any desired programme position.

1. Press the MENU button and select Preset, press the e or d but- ton and select Prog. Preset.

2. Press the 8 button to get Semi menu.

If Channel is not selected press the e or d button, once highlighted press the 7 or 8 button until the desired channel is found.

The selection changes colour to blue, to say that another channel has been found.

To change the Position already selected highlight by pressing the d

button. Press the -/-- button and enter 0-9 numbers or the 7 , 8 button until position is selected.

3. Press the d button and select Memory, press the OK button to

memorise.

Press the MENU button to exit.

●

Skip

Skip ON : in normal operation when the 5 or 6 button is

pressed this position will be skipped.

Skip OFF : Position is not skipped when 5 or 6 button is

pressed.

1. Press the MENU button and select Preset, press the e or d but- ton and select Prog. Preset.

2. Select Channel that you wish to be skipped or the Position. Select Skip and choose ON by pressing the 7 or 8 button.

3. Select memory. Press the OK button to store.

✐

You can still view a programme position that has been skipped by using the numeric buttons to select the programme position directly.

Setting menu

Preset menu

■

Swap

Use this channel swapping feature to swap the channels between two stored programme positions. This feature is particularly useful after automatic tuning.

You have to choose a programme that you wish to swap on the TV set. eg. Swap programme position 4 and 12.

1. Select programme position eg.4.

2. Press the MENU button and select Preset using the 7 or 8

button. Select Swap by pressing the e or d buttons.

3. Enter the new position eg.12. Press 1 and 2 numeric buttons.

4. Press the OK button to store, the number disappears.

5. Press the MENU button to exit and they are swapped.

■

Fine tuning

1. Press the MENU button and select Preset using the 7 or 8

button.

2. Press the e or d button and select Fine tuning.

3. Press and hold the 7 or 8 button to fine tune channels.

The tuning will be stored when you exit the menu. Press the MENU to exit.

Any changes made by fine tuning will remain even when the TV set is switched off by Mains Switch, until the channel has been retuned.

Preset menu

Teletext -

This is a free service to give you lots of varied informa-

tion such as news, sports results, weather and travel features.

Teletext reception

If your aerial signal is poor, the teletext reception operation may be erratic.

Teletext brightness level

You can change the teletext brightness level. Please return to TV mode.(See Picture menu -Text Bright on page 15).

Sound volume control

In teletext mode sound volume and muting can be controlled. However they are not displayed on the screen.

Teletext

■ Switching into /from standby mode

The Standby mode is used for switching the TV set off for short periods of time. In standby mode the TV is switched off but is still receiving mains power.

●

To turn the TV set into standby mode, press the 4 button.

The red

power indicator illuminates more brightly

●

To turn the TV set ON from standby mode, press any of the following buttons: 4,5, 6

or 0-9 buttons.

■

Auto shut off

This TV set will automatically switch into the standby mode, 10 minutes after a signal is no longer received. The time until the set will switch off is displayed on the screen.

■

Use of Audio Output Jacks

This TV provides the audio monitor output jacks on the left side of the cabinet. You can connect your audio equipment to these jacks to give you sound with your audio equipment.

■

VCR / DVD controls

If you find the power indicator flashing, please turn the TV set off with the Standby switch and disconnect the power cord from the power outlet and contact our Service desk.

This warning is a sign to let you know that the power protection function of this TV set is now operating.

To audio equipment

■

Screen options

Today there are various transmission formats with different size ratios, eg. 4:3 , 14:9, 16:9 and video formats such as letterbox.

■

AUTO

It automatically switches to the optimum screen mode according to the WSS signal provided in the receiving signal source. If the signal does not have it, the TV keeps current screen mode.

✐

This setting may cause the picture to change when a different format is received eg. when an advert is received.

✐ WSS (Wide screen signalling)

Some broadcasters transmit this signal and some VCR tapes have it included . The signal identifies the picture format ratio (16:9, 14:9, 4:3 etc.).

If WSS is not being received and you are not happy with your picture this TV provides you the option to change it with the following options.

Press the WIDE button repeatedly to select your desired setting.

Selecting of picture size

■

NATURAL

■

ZOOM (14:9)

■

TITLE IN (14:9)

■

ZOOM (16:9)

■

TITLE IN (16:9)

■

NORMAL

■

FULL

Common specification

Power source AC 220~240V 50Hz Television system System I Colour system PAL/NTSC4.43

(PAL/NTSC4.43/NTSC3.58 in AV mode)

Channel coverage UHF: 21-69.

Aerial input impedance 75 ohm

AV terminal

AV1: CENELEC Standard Input: Composite video, RGB and audio-L/R

Output:TV-output with composite video and

audio-L/R

AV2: CENELEC Standard Input: Composite video, RGB, S-VHS and

audio-L/R

Output:Monitor-output with composite video

and audio-L/R

Side AV terminal

AV3: RCA jacks Input: Composite video and audio-L/R

Heaphone socket Mini Jack

CE30LD3BK-B

Sound output (Continuous) 2 x 10W

Contrast Ratio 500:1

Screen (inches) 30 (viewing measured diagonally)

Display Resolution 1280 x 768 x (WXGA)

Viewing Angles H:170°, V:170°

Dimensions (WxHxD mm) 915 x 558 x 220 ( including stand )

Weight (kg) 20.5 ( including stand )

■

NO PICTURE, NO SOUND

●

Check if TV is plugged in.

●

Try a different channel, if OK, probably station trouble.

■

POOR PICTURE, SOUND OK

●

Adjust BRIGHTNESS control.

●

Adjust FINE TUNING control.

●

Check aerial connections.

■

NO COLOUR, PICTURE OK

●

Adjust COLOUR control.

●

Adjust FINE TUNING control.

●

Is the programme in colour ?

■

WEAK PICTURE

●

Check aerial connections on back of set.

●

Check aerial for broken wires.

●

Re-orient aerial.

The following faults are not caused by the receiver:

"GHOSTS"

Reflections of signals from mountains or high buildings will cause multiple images, called "Ghosts". These abnormal conditions can be reduced to minimum by repositioning aerial or by installing new one suited for your area.

"INTERFERENCE"

Interference may be caused by electrical appliances, car ignition systems, etc. This should normally be a temporary condition, but should this interference persist, contact your dealer.

■

Plug and Play Helpful hints.

If you do not fit an aerial into this TV set the Plug and Play feature may start up each time you switch on your TV.

To prevent this follow these instructions.

1. Switch on your TV set, the Plug and Play screen appears.

2. Press the MENU button on the remote control to clear the Plug and

Play screen.

3. A second screen will appear. Press the Return key to clear from the screen.

4. Press the D/A key to return to Analogue.

5. Press the MENU button to select the Menu screen. (as shown

below).

6. Select Preset Menu by pressing the 1 or 2 buttons.

7. Select Prog. Preset by pressing the 6 or 5 buttons and enter Semi by pressing the 1 button.

8. Press the 6 button and select Memory. Press the OK button to

cancel. (The OK? changes to OK).

9. The next time you switch on your TV set the Plug and Play screen will not be displayed.

Helpful hints

Specification

Sanyo U.K. Sales Ltd. (the company) warrants to the initial retail purchaser that if this equipment is or becomes defective and that, in the opinion of the Company, the defect is due to faulty material or workmanship the Company will, for a period of 12 calendar months from the date of sale to the original purchaser repair or replace, at its sole option, free of charge, any such defective component part of the equipment, always provided that:-

1: The equipment has at all times been used in accordance with

the operating instructions issued by the Company, and has not been connected to an electrical mains supply for which it has not been adjusted.

2: Accidental damage or damage caused by negligence of misuse

by the user, is specifically excluded.

3: Unauthorised repairs, or any modification to the equipment

which has not been expressly approved by the Company, shall render this warranty null and void.

4: Failure due to fair wear and tear of any item is specifically

excluded.

This warranty is not transferable and is only applicable within the United Kingdom (and the Republic of Ireland). Nothing in this express warranty affects the statutory rights available to the purchaser of this equipment.

Note: This warranty supersedes any other form of guarantee that may inadvertently have been enclosed with or attached to the product.

Dear Customer.

Thank you for buying

SANYO

. This equipment should give you many years of pleasure and faithful service but in the event that a fault occurs, the following notes for you guidance may be helpful:-

1: PLEASE RETAIN YOUR PURCHASE RECEIPT WHICH WILL

BE REQUIRED FOR SERVICE DURING WARRANTY.

2: If your Sanyo equipment proves faulty during the period of

guarantee, take it or send it back to the dealer who originally supplied it together with this guarantee and the proof of purchase. We have made arrangements with our approved dealers under which they will carry out in guarantee service repairs on our behalf. In this way, we hope to reduce to a minimum the amount of time you will be without your equipment.

3: If for some reason it is impossible to return the equipment to the

original supplier, please contact our Service Department at the address below for further advice.

4: Should the equipment require servicing after the expiry of the

guarantee period, take or send it to the original supplier or any other Sanyo dealer. He will be pleased to give you a quotation for the repair.

Service Department, Sanyo UK Sales, (A Division of SANYO Europe Ltd.),Sanyo House, Otterspool Way, Watford, Hertfordshire, WD2 8JX. Tel: 01923 246363

Warranty to customer

Part No. 1KA6P1P0133-B N2DM

Printed in U.K.

Sanyo CE30LD3BK-B Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual