Sanyo AVL-408, AVL-328, AVP-428, AVL-278 User Manual
Instruction Manual
True HDTV Flat Panel TV
AVL-278/328/408 LCD
AVP-428 Plasma Display
Series
Save all packaging material for possible reshipment should you move, etc.
Subscribe to HDTV cable or satellite?
Please consult pages 23 & 26 for aspect ratio information in order to maximize your viewing experience.
Call our HELPLINE 1-800-263-2244 for further assistance.
SANYO Canada Inc.
www.sanyo.ca
Table of Contents
Important Information ...........................................................................................................................................................1
Important Safety Precautions...............................................................................................................................................2
Preparation ..........................................................................................................................................................................5
Using the Remote Control .........................................................................................................................................5
Batteries for the Remote Control...............................................................................................................................5
Power Connection .....................................................................................................................................................5
Antenna Connection..................................................................................................................................................6
Identification of Controls ......................................................................................................................................................7
Main Unit ...................................................................................................................................................................7
Remote Control .........................................................................................................................................................9
Connections .......................................................................................................................................................................11
Cautions Before Connecting....................................................................................................................................11
Connect a VCR........................................................................................................................................................11
Connect a Camcorder..............................................................................................................................................12
Connect a DVD player.............................................................................................................................................13
Connect a DTV receiver ..........................................................................................................................................14
Connect a PC ..........................................................................................................................................................15
Connect a VCR for Recording ................................................................................................................................16
Turning the Unit On and Off ...............................................................................................................................................17
Turning the Unit On and Off.....................................................................................................................................17
Viewing the Menus and Displays.............................................................................................................................17
Memorizing the Channels ..................................................................................................................................................18
Selecting the Signal Source.....................................................................................................................................18
Storing Channels in Memory Automatically.............................................................................................................18
Adding and Erasing Channels .................................................................................................................................19
Basic Operations................................................................................................................................................................20
Changing Channels .................................................................................................................................................20
Adjusting the Volume...............................................................................................................................................20
Select Input Source Signal ......................................................................................................................................21
Selecting a Menu Language....................................................................................................................................21
Setting Picture....................................................................................................................................................................22
Customizing the Picture...........................................................................................................................................22
Using the Preset Picture Mode................................................................................................................................22
Setting System ...................................................................................................................................................................23
Setting System In TV Mode.....................................................................................................................................23
Adjusting Screen Aspect..........................................................................................................................................23
Reducing Picture Noise ...........................................................................................................................................23
VCR mode ...............................................................................................................................................................23
Loading Default Values............................................................................................................................................23
Setting System In VGA Mode..................................................................................................................................24
Changing the Position of Image...............................................................................................................................24
Adjusting Clock and Phase......................................................................................................................................24
Adjusting the Picture Automatically .........................................................................................................................24
Adjusting Screen Aspect..........................................................................................................................................25
Display Resolution Information................................................................................................................................25
Loading Default Values............................................................................................................................................25
Table of Contents (continued)
Setting System In YPbPr Mode .........................................................................................................26
Adjusting Phase ...................................................................................................................................26
Adjusting Screen Aspect ......................................................................................................................26
Reducing Picture Noise........................................................................................................................26
Loading Default Values ........................................................................................................................26
Setting Sound ................................................................................................................................................27
Customizing the Sound ........................................................................................................................27
Using the Preset Sound Mode .............................................................................................................27
Setting SRS effect................................................................................................................................27
Adjusting On-Screen Display.........................................................................................................................28
Adjusting OSD Position........................................................................................................................28
Adjusting OSD Transparence ..............................................................................................................28
Zooming OSD Menu ............................................................................................................................28
Setting OSD Off Time ..........................................................................................................................28
Loading default values .........................................................................................................................28
TVPC Operations ..........................................................................................................................................29
Viewing the TVPC ................................................................................................................................29
Selecting the Signal Source for the TVPC Frame................................................................................29
Changing Channels for the TVPC Frame ............................................................................................29
Changing the Position of the TVPC Frame ..........................................................................................30
Adjusting the Size of TVPC Frame ......................................................................................................30
Viewing Picture-by-Picture ...................................................................................................................30
Using Hotkeys ...............................................................................................................................................31
Setting Sleep Timer..............................................................................................................................31
Setting Audio Mode..............................................................................................................................31
Adjusting Back Light of the Panel ........................................................................................................31
Freezing Picture ...................................................................................................................................31
Viewing Closed Captions...............................................................................................................................32
Turning Closed Caption On or Off........................................................................................................32
Setting Closed Caption ........................................................................................................................32
Setting CC When Mute ........................................................................................................................32
Adjusting Child Lock Settings ........................................................................................................................33
Child Lock ............................................................................................................................................33
Turning Child Lock On or Off ...............................................................................................................35
Changing the Password .......................................................................................................................35
Adjusting the Movie Rating ..................................................................................................................35
Adjusting the TV Rating .......................................................................................................................35
Adjusting Canadian English Rating......................................................................................................36
Adjusting Canadian French Rating ......................................................................................................36
Troubleshooting.............................................................................................................................................37
Specifications ................................................................................................................................................38
Important Information
Thank-you for choosing SANYO. This product can display true HDTV (High definition) pictures. A subscription to your cable or
satellite provider is required.
WARNING:
CAUTION-To reduce the risk of electric shock, do not perform
"Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National
Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to
the grounding system of the building, as close to the point of cable entry as practical.”
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE.
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
any servicing other than that contained in the
operating instructions unless you are qualified to
alert the user to the presence of uninsulated
dangerous voltage within the product's
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal of these materials may be
regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the
Electronic Industries Alliance: www.eia.org
FCC STATEMENT
FCC Notice
LCD TV: A CLASS B digital device
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC CAUTION:
Pursuant to 47CFR, Part 15.21 of the FCC rules, any changes or modifications to this monitor not expressly approved by the
manufacturer could cause harmful interference and would void the user's authority to operate this device.
WARNING: This is a CLASS B product. In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures to counter interference.
1
Important Safety Precautions
Electrical energy can perform many useful functions, but it can also cause personal injuries and property damage if improperly
handled. This product has been engineered and manufactured with the highest priority on safety. But IMPROPER USE CAN
RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order to prevent potential danger, please observe the
following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of your
LCD TV product, please read the following precautions carefully before usiang the product.
1. Read these instructions---All operating instructions must be read and understood before the product is operated.
2. Keep these instructions---These safety and operating instructions must be kept in a safe place for future reference.
3. Heed all warnings---All warnings on the product and in the instructions must be observed closely.
4. Follow all instructions---All operating instructions must be followed.
5. Do not use this apparatus near water---for example, near a bathtub, washbowl,
kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
Do not use immediately after moving from a low temperature to high temperature
environment, as this causes condensation, which may result in fire, electric shock, or
other hazards.
6. Clean only with dry cloth---Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
7. Ventilation---Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions. The vents and other openings in the cabinet are
designed for ventilation. Do not cover or block these vents and openings since
insufficient ventilation can cause overheating and/or shorten the life of the product.
Do not place the product on a bed, sofa, rug or other similar surface, since they can
block ventilation openings. This product is not designed for built-in installation; do not
place the product in an enclosed place such as a bookcase or rack, unless proper
ventilation is provided or the manufacturer’s instructions are followed.
8.Heat sources---Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that produce heat.
9.Grounding or Polarization---Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10.Power cord protection---Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11.Attachments---Only use attachments/accessories specified by the manufacturer. Do not use attachments not recommended by
the manufacturer. Use of improper attachments can result in accidents.
2
Important Safety Precautions (continued)
12. Stand---Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. Do not place the product on an unstable trolley,
stand, tripod or table. Placing the product on an unstable base can cause the product to fall,
resulting in serious personal injuries as well as damage to the product. When mounting the
product on a wall, be sure to follow the manufacturer’s instructions. Use only the mounting
hardware recommended by the manufacturer.
13. Move Carefully---When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over. Sudden stops, excessive force and uneven floor
surfaces can cause the product to fall from the trolley.
14. Lightning---Unplug this apparatus during lightning storms or when unused for long periods
of time.
For added protection for this television equipment during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and disconnect
the antenna. This will prevent damage to the equipment due to lightning and power-line surges.
15. Servicing---Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
16. Replacement parts---In case the product needs replacement parts, make sure that the service person uses
replacement parts specified by the manufacturer, or those with the same characteristics and performance as the
original parts. Use of unauthorized parts can result in fire, electric shock and/or other danger.
17.Overloading---Do not overload wall outlets, extension cords, or convenience receptacles on other
equipment as this can result in a risk of fire or electric shock.
18.Entering of objects and liquids---Never insert an object into the product through vents or openings. High voltage flows in the
product, and inserting an object can cause electric shock and/or short internal parts. For the same reason, do not spill water or liquid
on the product.
19.Damage requiring service---If any of the following conditions occur, unplug the power cord from the AC outlet, and request a
qualified service person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid is spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls not described in
the instructions can cause damage, which often requires extensive adjustment work by a qualified technician.
e. If the product has been dropped or the cabinet has been damaged in any way.
f. When the product displays an abnormal condition or exhibits a distinct change in performance. Any noticeable abnormality in the
product indicates that the product needs servicing.
20.Safety checks---Upon completion of service or repair work, request the service technician to perform safety
checks to ensure that the product is in proper operating condition.
21.Wall or ceiling mounting---When mounting the product on a wall or ceiling, be sure to install the product according to the method
recommended by the manufacturer. This is a safety feature.
3
Important Safety Precautions (continued)
22. Power source---This product is intended to be supplied by a listed power supply indicated on the marking label. If you are not sure
of the type of power supply to your home, consult your product dealer or local power company. For added protection for this product
during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect
the cable system. This will prevent damage to the product due to lightning and power line surges. When the unit has to be used with
another power supply voltage, the power cable must be changed. Consult your product dealer. The socket outlet should be installed
near the equipment and easily accessible. Use only the power cord designated by our dealer to ensure safety and EMC. When
connecting other products such as VCRs and personal computers, you should turn off the power of the unit for protection against
electric shock.
23.Panel protection---The LCD panel used in this product is made of glass. Therefore, it can
break when the product is dropped or impacted upon by other objects. Be careful not to be
injured by broken glass pieces in case the LCD panel breaks.
24.Pixel defect---The LCD panel is a very high technology product, giving you finely detailed pictures. Occasionally, a few non-active
pixels may appear on the screen as a fixed point of blue, green or red. Please note that this does not affect the performance of your
product.
< If an outside antenna is connected to the television equipment, be sure the antenna system is grounded so as to provide some
protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code provides information with
respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding
electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
NEC—NATIONAL ELECTRICAL CODE
< An outside antenna system should not be located in the vicinity of overhead power lines or
other electric light or power circuits, or where it can collide with such power lines or circuits.
When installing an outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits, as contact with them might be fatal.
4
Preparation
Using the Remote Control
< Use the remote control by pointing it towards the remote sensor window of the set. Objects
between the remote control and sensor window may prevent proper operation.
3
0
0
3
Cautions regarding use of remote control
< Do not expose the remote control to shock. In addition, do not expose the remote control to
liquids, and do not place in an area with high humidity.
< Do not install or place the remote control under direct sunlight. The heat may cause deformation of the unit.
< The remote control may not work properly if the remote sensor window of the main unit is under direct sunlight or strong lighting. In
such a case, change the angle of the lighting or LCD TV set, or operate the remote control closer to the remote sensor window.
Batteries for the Remote Control
If the remote control fails to operate the LCD TV functions, replace the batteries in the remote control.
Open the battery cover.
1
Insert two size-AAA batteries.
2
Replace the cover and slide in
3
reverse until the lock snaps.
5m
< (Slide the cover while pressing
down.)
Precautions on battery use
Improper use of batteries can result in a leakage of chemicals and/or explosion. Be sure to follow the instructions below.
< Place batteries with their terminals corresponding to the (+) and (–) indications.
< Different types of batteries have different characteristics. Do not mix batteries of different types.
< Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries and/or cause old batteries to
leak chemicals.
< Remove batteries as soon as they are non-operable. Chemicals that leak from batteries can cause a rash. If chemical leakage is
found, wipe with a cloth.
< The batteries supplied with the product may have a shorter life expectancy due to storage conditions.
< If the remote control is not used for an extended period of time, remove the batteries from the remote control.
< (Place the batteries with their terminals
corresponding to the (+) and (–) indications
in the battery compartment.)
Preparation (continued)
Antenna Connection
CABLE TV (CATV) CONNECTION
A 75-ohm coaxial cable connector is built into the set for easy hookup. When connecting the 75- ohm coaxial cable to the set, screw
the 75-ohm cable to the ANT. Terminal.
Some cable TV companies offer “premium pay channels”. Since the signals of these premium pay channels are scrambled, a cable
TV converter/descrambler is generally provided to the subscriber by the cable TV company.
This converter/descrambler is necessary for normal viewing of the scrambled channels. For more specific instructions on installing
cable TV, consult your cable TV company. One possible method of utilizing the converter/descrambler provided by your cable TV
company is explained below. Please note: An RF switch provided with two inputs (A and B) is required (not supplied).
RF switch (not supplied)
OUT
Cable TV converter/
descrambler
(not supplied)
“A” position on the RF switch (not supplied) : You can view all unscrambled channels by using the TV’s channel keys.
“B” position on the RF switch (not supplied) : You can view the scrambled channels via the converter/descrambler by using the
converter’s channel keys.
IN
Two-set
signal
splitter
(not
supplied)
Cable TV Line
Note:
Consult your Dealer or Service Center for the type of splitter, RF switch or combiner that might be required.
ANTENNAS
The antenna requirements for good color television reception are more important than those for black & white television reception.
For this reason, a good quality outdoor antenna is strongly recommended.
The following is a brief explanation of the type of connections that are provided with the various antenna systems.
1. A 75-ohm system is generally a round cable with F-type connector that can
easily be attached to a terminal without tools (not supplied).
2. A 300-ohm system is a flat “twin-lead” cable that can be attached to a 75ohm terminal through a 300-75-ohm adapter (not supplied).
OUTDOOR ANTENNA CONNECTION
Use one of the following two diagrams if you connect an outdoor antenna.
A: Using a VHF/UHF combination outdoor antenna.
B: Using separate VHF and/or UHF outdoor antennas.
Connect the outdoor antenna cable lead-in-1.j0.:hm terminan on ths rrne o5-
Identification of Controls
Main Unit
Some models
Remote Sensor
Power Indicator
A blue indicator lights when the power is on
and a red indicator lights when in the
standby mode.
Or on some models
SOURCE
CH+
CH–
VOL+
VOL–
MENU
Channel Up/Down
Volume Up/Down
Select Input Signal (Not all models)
Menu
Power On/Standby
1. POWER
Press this button to turn the unit ON from STANDBY mode. Press it again to turn the set back to
STANDBY.
2. MENU
Press this button to access the Menu main page.
3. SOURCE
To access signal source select menu. (Not all models)
4. VOL+/-
Press the VOL+ or VOL- button to directly increase or decrease the sound volume level;
in OSD Menu, press these buttons to adjust the value or setting of each item.
5. CH+/-
Note:
Functions of VOL+/-, CH+/-, MENU, SOURCE and POWER are also provided on the remote control. This
operation manual provides a description based on operating functions with the remote control.
7
Identification of Controls (continued)
Identification of Controls (continued)
Remote Control
1. POWER
Turn the unit on or off.
2. CH+/-: Use to switch channels;
In Menu operation, use CH+/- to select menu item.
VOL+/-: Use to adjust volume;
In Menu operation, use VOL+/-to adjust selected item.
3. Menu
To access the Menu main page or exit menu operation
4. BK
To adjust panel backlight
6. S.M
Sound mode select
7 P.M
Picture mode select
8. 0~9 number buttons
Direct channel select
9. Source
To access source select menu
10. Mute
Sound mute
11.Enter
To confirm, enter submenu or toggle the settings of the
selected menu;
13. SRS
To turn the SRS sound effect on or off *
14. Return
To quickly jump between current channel and last selected
The SRS symbol is a trademark of SRS Labs,Inc.
*
SRS technology is incorporated under license from SRS Labs,
Inc.
Remote Control
17
18
19
22
24
25
26
Identification of Controls (continued)
17. Auto
To rectify the picture automatically in VGA mode
18. PBP
To activate picture-by-picture
19. POS
To adjust TVPC frame position
20. TVPC
To activate TVPC function
21. P.S.
To select signal source for TVPC frame
22. CCD
To select CCD on/off and CCD channel
23. Up, Down
To change channel of TVPC frame
24. Screen
To select screen aspect ratio
25. Size
To adjust TVPC frame size
26. Still
To freeze current picture
Connections
Cautions Before Connecting
Carefully check the terminals for position and type before making any connections.
The illustration of the external equipment may be different depending on your model.
Loose connectors can result in image or color problems. Make sure that all connectors are securely inserted into their terminals.
Refer to the operating manual of the external device as well.
When connecting an external device, turn the power off on the panel to avoid any issues.
Connect a VCR
YY
Yellow (VIDEO)
WW
White (AUDIO L)
RR
Red (AUDIO R )
D-SUB
-ub IN
DSU
D-Sub AUDIO
DVI IN
DVI
AUDIO
ANTENN
A
HEADPHONE
AVI INPUT
AV2 INPUT
AV OUT
S VIDEO
R
AUDIO
L/MONO
VIDEO
-
AV1 IN/ S-VIDEO IN
VCR
LCD Models
S-video
cable
RR
WW
or
Video
cable
YY
Audio
cable
WW
YY
AV OUT
AV IN
AUDIO
AUDIO
RR
RLVIDEO
RLVIDEO
Rear of the VCR
Plasma Display Models
AV INPUT 1
VIDEO RL AUDIO
S-VIDEO
AV INPUT 2
VIDEO RL AUDIO
-
S VIDEO
AV OUTPUT
VIDEO RL AUDIO
ANT INANT OUT
HEADPHONE
BOTTOM VIEW
How to connect:
Connect the Audio/Video cables between the Audio (L/R)/Video jacks on the unit and VCR.
Note:
For better video, you can use the S-video terminal if your source supports it.
To play VCR
1. Turn on your TV, press Source button on the remote control.
2. Press CH+/- to select Video1(AV1 IN) or SVideo and press Enter to confirm.
3. Turn on your VCR , insert a videotape and press the Play button.
11
Source Select
VGA
RF
Video1
Video2
SVideo
YPbPr1
YPbPr2
Loading...