Sanyo ASW-A100HT Instruction Manual

INSTRUCTION MANUAL

MICROCOMPUTER CONTROL
FULLY AUTOMATIC WASHING MACHINE

MICROCOMPUTER CONTROL
FULLY AUTOMATIC WASHING MACHINE

ASW-A100HT

Before operating this washing machine, please read
these instructions carefully and completely.

Before operating this washing machine, please read
these instructions carefully and completely.

WARNING - This appliance must be earthed.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:

Green/yellow: Earth Blue: Neutral Brown: Live

As the colours of the wires in the mains lead of this appliance may not correspond
with the coloured markings identifying the terminals in your plug, proceed as follows:

Light

The wire which is coloured green and yellow must be connected to the terminal

in the plug which is marked with the letter E or by the earth symbol
or coloured green or green and yellow.

The wire which is coloured light blue must be connected to the terminal which is

marked with the letter N or coloured white.

The wire which is coloured brown must be connected to the terminal which is marked

with the letter L or coloured black.

●

●

●

SPECIFICATIONSSPECIFICATIONS

COD E NO.30 1-6-4 11S -97 2- 40 BCOD E NO.30 1-6-4 11S -97 2- 40 B

610(W) x 585(D) x 1000(H) mm
60 litres
AC Local voltage

Dimensions

Power Source

Water level (HIGH)

Power Consumption
Required Water Pressure

2

FOR WASHER PLUG TOP 3 PIN

● If the 2-pin type of socket-outlet has a grounding terminal,
securely attach the end of the Grounding Wire to the
terminal.

● When grounding the washer, connect the grounding wire
before plugging in the Power Cord.

● If the 2-pin type of the socket-outlet has no grounding
terminal, consult your nearest dealer or securely attach
the end of Grounding Wire to a suitable grounding point,
such as a metal cold water pipe.
Never connect the Grounding Wire to a gas pipe.

● Unplug the Power Cord before disconnecting the
Grounding Wire.

For BS Standard Plug With A 13 Amp Fuse

( )

Grounding
Terminal

Grounding
Wire Of
Washer

Grounding
Wire

Grounding
Rod

FOLLOWING CAUTIONS ARE FOR WASHER USING DOUBLECORE
CORD ONLY.

SAN YO Elec tric Co .,Ltd .SAN YO Elec tric Co .,Ltd .

400 W

0.03 MPa ~ 1.0MPa
(0.3 kgf/cm ~ 10 kgf/cm )

2

22

·U washing function: completely clean the dirty.

·M : 9 water currents could be adjusted during

washing.

·Digital display: easy operation.

· Anti-crease spin .

·Custom course and remember function.

·Jumbo Stainless Steel inner tub with diameter 460mm: Better washing and

spinning.

ltrasonic

ultiple water power function

Soft Spin:

Never put your hand(s) into the Wash/Spin
Tub while the washer is operating.

·If you reach into the Wash/Spin Tub,
it can cause injury.

·If the Wash/Spin Tub dose not stop
within 15 seconds after
the Washer Lid is opened,
turn the washer off
immediately and call
a service person.

Be sure to connect Power Plug and Power
Cord properly.

·Be sure to plug the Power Cord into a
proper socket-outlet for the washer.

·An improperly attached plug
may catch fire.

·Never disconnect by pulling
the cord. Hold the plug as you
pull it out.

·Never use a damaged Power
Cord.

·Never connect and/or
disconnect the Power Plug with wet
hands, it may cause an electric shock.

Be sure not to bring any type of flame near
the washer or put lit cigarettes or volatile
materials on the top of the washer.

·It may deform the washer
or catch fire, because this
washer has a large
number of plastic parts.

Never wash items stained with benzine,
kerosene, thinner or gasoline.

·It may cause a risk
of fire or explosion.

Do not install the washer in
the bathroom or very humid
place.

·It may cause a
malfunction or an
electric shock.

Do not allow children to play on
or in the washer.

·If a child accidentally falls
in to the Wash/Spin Tub,
serious injury could occur.

Be sure not to splash or pour
water on the Control Panel.

·It may cause a malfunction

or an electric shock.

Do not allow your washer to be repaired
by an unqualified service person.

·It may cause a risk of accidental
fire.

·If the washer operates
abnormally, it may cause injury.

WARNINGSWARNINGS

FEATURES FEATURES

… … … … … … … … … … … … … … … … … … … … … … … …

… … … … … … … … … … … … … … … … … … … … … … … …

… … … … … … … … … … … … … … … … … … … … … …

… … … … … … … … … … … … … … …

… … … … … … … …

… … … … … … … … … … … …

… … … … … … … … … … … … … … … …

… … … … … … … … … … … … … …

… … … … … … … … … … … … … … … … … …

… … … … … … … … … … … … … … … …

… … … … … … … … … … …

… … … … ………… … … … … … … … … …

… … … … … … … … … … … … … … … … …

… … … … … … … … … … … … … …

… … … … … … … … … … … … … … … … … … … …

… … … … … … … … … … … … … … … … … … … … …

… … … … … … … … … … … …

… … … … … … … … … … … … … … … … …

… … … … … … … … … … … … … … … … …

… … … … … … … … … … … … … … …

… … … … … … … … … … … … … … … …

… … … … … … … … … … … … … … … … …

11

2

2

3

3

4-6

7-8

9

10

11

11

12

13

14

14

14-16

14

15

15

15

15

15

16

16

16

16

17

18

18

CONTENTSCONTENTS

WARNINGS

ACCESSORIES

NAME OF PARTS

INSTALLATION INSTRUCTIONS

NAMES AND FUNCTIONS OF CONTROL PANEL

FEATURES

NORMAL USAGE

HOW TO USE THE BLANKET COURSE

COURSE CHOOSING GUIDE

HOW TO USE THE CUSTOMIZED COURSE

HOW TO USE PRESET WASHING

THREE TYPES OF RINSE

VARIOUS FUNCTIONS

ULTRASONIC FUNCTION

WATER LEVEL SETTING

TWO CLEAN STEPS FUNCTION

SHOWER RINSE

HOW TO DRAIN REMAINING WATER

CHILD LOCK FUNCTION

PROCESS CHANGING

DELETE THE END BUZZER

NO TROUBLE CONDITIONS

TROUBLE SHOOTING GUIDE

Back Cover

… … … … … … … … … … … … … … … … …

SPECIFICATIONS

THE PREPARATION OF LAUNDRY BEFORE WASHING

… … … … … … … … … … … … … … … … … …

MULTIPLE WATER POWER FUNCTION

CARE AND MAINTENANCE

… … … … … … … … … … … … … … … … …

REMEMBER FUNCTION

CYCLONE DRY

● Wipe the Power Plug with a soft cloth
and remove any dust to prevent a risk of
the accidental fire before plugging into
the socket-outlet.

● Do not plug two Power Cords in one
socket-outlet.

NAME OF PARTSNAME OF PARTS

Water
Supply Hose

Drain Hose

“Magic"
Hose Joint

Bottom Cover

Scr ew

33

Instruction manual

ACCESSORIESACCESSORIES

Hose Band

44

INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS

1.Unplug the Power Cord of the washer.

2.Gently lay down the front side of washer on a soft mat or
cushion.(Becareful not to dent the Frame.)

3.Insert the attached Bottom Cover into the hooks of Leg
by straightly pushing until it reaches into the front hooks.

4.Fasten the Bottom Cover with a screw.

5.Gently set the washer upright.

Bot tom
Cov er

Scr ew

1.Choose a dry location out of sunlight for the washer.

2.Install the washer on a stable and level surface.

Location of WasherLocation of Washer

Inc lined f loor

Uns table f loor

Leg

● Do not block the ventilation openings on the bottom of washer by carpeting when the

washer is installed on a carpeted floor.

Type B

Type C

At le ast 16m m

Wate r leak

Type B :

The length of the mouth of the faucet needs to be at least 16mm.
If it is less than16mm, the"Magic"Hose Joint can not be installed.

Type C :It may cause water leaking.

CAUTIONS:

Do not use water which is hotter than 50 .
If your faucet is not suitable, consult your dealer.

●

● please

℃℃

CAUTION:

Attaching the "Magic" Hose Joint to a FaucetAttaching the "Magic" Hose Joint to a Faucet

Type A :is the most suitable

Faucet:

Type A

Lock Nut

Adjustable Leg

Up

Loosen①

②Down

③Tighten

Fundus

Installing the Bottom CoverInstalling the Bottom Cover

Fro nt

Bac k

3.Adjust the Adjustable Leg of washer if necessary to make the washer level as shown
in the figure.

The maximum permissible inclination of the supporting surface is 2 . ●

Was he r Li dWas he r Li d

Lint FilterLint Filter

Was h/ Sp in Tu bWas h/ Sp in Tu b

Adjustable LegAdjustable Leg

Contro l PanelContro l Panel

Softener DispenserSoftener Dispenser

FrameFrame

"Magic"Hose Joint"Magic"Hose Joint

FaucetFaucet

PulsatorPul sa to r

LegLeg

Drain Hos eDrai n Hose

Power CordPower Cord

Wat er S up ply Ho seWat er S up ply Ho se

Power PlugPower Plug

Detergent TrayDetergent Tray

(O ne )(O ne )

(Close water supply
after operation)

55

Extension of the Drain HoseExtension of the Drain Hose

When extending the external Drain Hose, please follow the figure for the length
and height.

below

Extension Hose

No straight

Straight

Height

Max.15cm

Length

Max.1m

Max.3m

Set the clip part of Hose Band sideways to prevent touching the Leg. Which may cause a
vibration noise.

Dra in Outl et

Dra in Hose

Hos e Band

INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS

66

Installing Th e Dr ai n Ho seInstalling Th e Dr ai n Ho se

Inside Hose

Hose Protector

Drain Outlet
(A Sectional Plan)

Drain Hose

Leg

Hose Band

Max.1 5c m

Max.1 m

1.Unplug the Power Cord of the washer.

2.Detach the Back Cover by loosening
screws at the back side of the washer.
Detach outer Drain Hose and gently lay
down the front side of washer on a soft
mat or cushion.

● Be careful not to open the Washer Lid and

dent the frame.

3.Detach the Cap from the left side of leg.

4.Loosen the Hose Band and pull the inner
Drain Hose out of the Drain Valve. Pull the
Hose Band out of the inner Drain Hose.

5.Remove right and left Tabs of Drain Outlet one side by another side pushing the Tabs
both in side and outside and pull the Drain Hose out toward outside of .leg

6.Let the inner Drain Hose through outside of left hole and set the protrusive guard of
inner Drain Hose to the square cutting part of , then attach the Drain Out let of the

hose until fitting the Tabs certainly to the .

leg

leg

8.Attach the Cap to the right hole.

9.Reattach Back Cover and gently set the washer upright.

Changing the Drain Hose DirectionChanging the Drain Hose Direction

You can change the direction from right side to left side.

Put gloves on to prevent injury of your hands when changing the Drain Hose direction.

NOTE:

NOTE:

Dra in Valve

Drai n Valve

Hose Clip

Hose Clip

Drain hole cover

Drain Hose

Drain Hose

Drain hole

Drain hole

7.Connect the inner Drain Hose to the Drain Valve in place and fix the Hose Band as
shown below.

f you do not attach correct position marked with ,it can damage the inner Drain Hose

and cause a water leaking through the torn position.

● I

How to Attach the “ Magic ” Hose Joint How to Attach the “ Magic ” Hose Joint

1.Loosen the four screws and slide the top of the "Magic"Hose Joint(section A in the
figure)onto the faucet. Then, securely tighten the four screws provided with the
“Magic" Hose Joint by using a screwdriver to secure the top of the joint to the faucet.

2.Remove the CAUTION label from the "Magic" Hose Joint.

Installing Water Supply Hose to the WasherInstalling Water Supply Hose to the Washer

1.Turn the nut clockwise while holding the hose.
Turn the nut counterclockwise after turning the

faucet off when you want to detach the Water
Supply Hose.

●

3.Turn the male coupler on the joint (section B in the figure) clockwise to attach it securely

to the top of the joint (section A in the figure).

The appliance is to be connected to the

water mains using new Water Supply
Hose and “Magic" Hose Joint and old
hose-sets should not be reused.

●

Joi nt Ring

1.While pushing the sleeve on the female coupler
(section D in the figure) of the joint down with
your fingers, connect the female coupler to the
male coupler (section C in the figure).

2.Release the sleeve, then push the Water Supply

Hose up into the “ Magic ” Hose Joint until it
clicks into place.

3.Pull the Water Supply Hose down to make sure

that it is securely attached.

How to Detach the Water Supply HoseHow to Detach the Water Supply Hose

INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS

Scr ew

CAUTION
label

Abo ut 4mm

A

B

Aft er tigh tened

(Abo ut 2mm or l ess)

Loc k Lever

Sle eve

C

D

CAUTION:

If outer diameter of faucet is larger than
calibre of the Joint Ring, loosen the four
screws and remove the Joint Ring from
the "Magic" Hose Joint.

Nut

Hos e

1.Turn the faucet off.

2.Press the POWER ON/OFF button to turn the power on ,the

NORMAL button and the START/PAUSE button.

3.Press the POWER ON/OFF button to turn the power off

15 seconds later.

Please read the following procedure in order to avoid spilling water when detaching the
Water Supply Hose.

4.While pushing the lock lever and the sleeve on the female

(section D in the figure)of the joint down with your fingers,
detach the female coupler from the male coupler
(section C in the figure).

Connecting the Water Supply Hose to the “ Magic ” Hose JointConnecting the Water Supply Hose to the “ Magic ” Hose Joint

Lock
Lever

Sle eve

C

D

88

77

1616

1414

NAMES AND FUNCTIONS OF CONTROL PANELNAMES AND FUNCTIONS OF CONTROL PANEL

99

DETERGENT IndicationDETERGENT Indication

·These are the spoon

indications of the
DETERGENT volume.

·Refer to "DETERGENT

AND LOAD
RECOMMENDATIONS"
on page 9.

·This indicator shows
remained time during
washing.

·This indicator
shows

.

·

rinsing
times and rinsing
type

“ ”means

Overflow Rinse.

(E.g.) Remaining time is 20 minutes

·This indicator shows when
the washing is finished
during presetting.

(E.g.) Finish washing 2 hours later

·When abnormal conditions
occur, the indicator will
indicate warning.

(E.g.) Water does not flow(E.g.) Washing time is 10 minutes

REMAINING

PRESET

CHILD LOCK

REMAINING

PRESET

CHILD LOCK

·

this indicator

shows

When setting SOAK and

WASH process,

the time of you set.

WATER LEVEL Button
CHILD LOCK Function

WATER LEVEL Button
CHILD LOCK Function

●You can choose the
appropriate water level
that matches the load size.

●You can set CHILD LOCK
function. Refer to CHILD
LOCK function at page 16.

●Different water levels for
washing rinsing optional.

Detailed operation please

refer to Page 15.

1515

1616

TIMER and PRESET IndicatorsTIMER and PRESET Indicators

RINSE IndicationRINSE Indication

SPIN IndicationSPIN Indication

·This indicator
shows spinning
time.

·“ ”means

Cyclone Dry.

START/PAUSE ButtonSTART/PAUSE Button

·

·

·

This button can be use to start the
washer operation.
This button can also be used to
temporarily stop the washer

operation.

To restart the washer operation,
press the START/PAUSE button
again.

NOTES:

·This is not a CANCEL button.

·If you want to delete the End Buzzer, press
the START/PAUSE button and hold down for
about 4 seconds until beeping stops.

To turn the power on, press the POWER
ON/OFF. When you want to turn off the
power, press the POWER ON/OFF again.

When washing has finished, the power
will be turned off in 5 seconds
automatically. (When you Setting
Remained water Draining function, the
time is 10 minutes).

● If you leave the washer turning on without
starting the operation, the power will be
turned off in 10 minutes by itself.

·

PROCESS ButtonPROCESS Button

●The PROCESS Button can
be used to set a variety of
wash programs.

●To choose the washing course,

press COURSE button.

NOTE:

If you choose the NORMAL, HEAVY

DUTY or CUSTOM course, the washer
will automatically begin the NEURO &
FUZZY operation.

●

COURSE ButtonCOURSE Button

●Press WATER POWER button to

adjust water current during washing
or rinsing. Press it once more, the
digital indicates “ H0 (standard
water flow), H1, H2, H3, H4,
( stronger. H4 is the strongest);L1,
L2, L3, L4 (weaker, L4 is the
weakest).

●And this function could not be set

for DELICATE or BLANKET course.

WATER POWER ButtonWATER POWER Button

POWER ON/OFF ButtonPOWER ON/OFF Button

Press the SOFT SPIN button,
the light above flashes.

● After pressing SOFT SPIN,
the last 2 minutes spinning
will be soft spin, this avoid
clothes creasing.
(This function cannot be
operated the DELICATE
and BLANKET course.)

SOFT SPIN ButtonSOFT SPIN Button

●Press this button to
preset the finish
time of washing.

●The number
indicated means the
finishing time of
washing.

●Preset function
could not be used
for DELICATE
course.

1313

PRESET ButtonPRESET Button

1212

1414

(E.g.) Cyclone Dry 1 hour

Lighting on during Cyclone Dry

(E.g.) Overflow Two times Rinse

Lighting on during Overflow Rinse

1515

1 01 0

99

10~25 25~3 5 35~50 50 ~7 0

16 L

24 L

30 L 3 6 L

47 L

54 L

60 L

42 L

1 1 2 2 3 3 44

Preparation:
Connect the Drain Hose. Connect the Water Supply Hose to the faucet and turn the
faucet on. Plug the Power Cord into a socket-outlet.Load the laundry into the washer.

·Make sure that screws of "Magic" Hose Joint are tighten before opening the faucet. If
screws are loose, it may cause water to leak.

DETERGENT AND LOAD RECOMMENDATIONSDETERGENT AND LOAD RECOMMENDATIONS

Water VolumeWater Volume

(Approx. L)

Water LevelWater Level

Detergent
Indicators

Detergent
Indicators

You may adjust the detergent volume according to the type of
detergent-follow recommendations on package.

Other detergent
volume

Other detergent
volume

Powdered
detergent
volume (g)

Powdered
detergent
volume (g)

HOW TO USE THE BLANKET COURSEHOW TO USE THE BLANKET COURSE

For washing blanket and other bulky items.

·The water level will be changed to 8 automatically when BLANKET course set. While
you can adjust it from level 5 to level 8 by hand according to the blanket or the bulky
items size.

1.Press POWER ON/OFF button and open the washer lid.

2.Press COURSE button continuously and choose the BLANKET course (The BLANKET
Light flashes).

3.After the detergent is dissolved with proper amount of warm water (approx. 30 ), pour
it into the tub of the washing machine.

4.Fold up the blanket as the method showed in the figures below and put it into the
washing tub.

5.Press the START/PAUSE button.

6.Close the washer lid.

·The washer will stop working automatically before spinning if the washer lid is not
closed.

·The buzzer will alarm at the end of operation and the power will be switched off
automatically in 5 seconds.

·Then please shut water supply and clean the filter.

℃℃

1.Press the POWER ON/OFF button.

2.Press the START/PAUSE button.

·Sensor tests the clothes weight automatically. ( For NORMAL, HEAVY DUTY,

CUSTOM). Auto choose the proper Water Power, Water Level, Wash and spin time,
rinse type.

3.

Use recommended amount of detergent as shown in chart.

Put it into the wash tub with
the edge downwards

Fold in two by the
long side

Fold 4 times in the
same direction

Roll up the blanket.

4.Close the washer lid.

● The washer will alarm and stop working before spinning if the washer lid is not closed.

● You can use softener, pour the softener slowly to Softener Dispenser before washing.

● Too much detergent causes poor rinsing and too little detergent causes poor washing.

Procedure

Take out blanket and hang it up.

NOTICE:

Clean the dirty side by hand firstly.
Use proper volume detergent.
It is better to clean dirty by warm water (approx. 30℃).

·

·

·

·If the blanket floats out during washing, please press START/PAUSE button, the

washer will stop working temporarily. Then, please push the blanket down, and press
START/PAUSE again to continue washing.

How to fold up the blanket and put it into the washing tub.

NORMAL USAGENORMAL USAGE

Procedure

Was h Fi ni sh

1

2

1 11 1

1 21 2

1515

11

99

0 5 1 0 … … 3 5 4 00 5 1 0 … … 3 5 4 0

0 1 2 … … 1 9 2 00 1 2 … … 1 9 2 0

0 1 2 … … 8 90 1 2 … … 8 9

0 1 2 30 1 2 3

1.Press POWER ON/OFF button .

2.Press COURSE button to Select the course you want.

3.Press the PROCESS button to select the process and time .

4.Press WATER LEVEL button, choose proper water level .

·Putting detergents.

5.Close the washer lid.

6.press the START/PAUSE button.

·At the end of working the buzzer will sound

·The CUSTOM course could be remembered.

Min. ( This function is not available for DELICATE/
BLANKET course).

COURSE CHOOSING GUIDECOURSE CHOOSING GUIDE

COURSE

WASH
POWER

WASHING

RINSING TYPE

SPINING
TIME(min.)

TIME(min.)

● WAS H ti me i nd ic at in g

● SOAK time indicating

● RINSE times indicating

● SPIN time indicating

Press PROCESS button choose your like cycle. The light moves right one by one when
press.

Min.

Min. ( Except the DELICATE course).

Min. ( For DELICATE course).

NORMAL

CUSTOM

HEAVY
DUTY

BLANKET

DELICATE

Standard

Standard

Strong

Soft

Blanket

OPERATION STATUS FOR THE PROGRAM

SUITABLE
CLOTHE

Normal clothes

Kinds of
clothes

Dirty clothes
like working
coat

Blanket or
Bulky

Women under­wear, articles
with embroider

5~12

Soak10

+

Wash10

12

7~14

6

5~6

5

7~8

8

2

Shower Rinse 1 times,
Water Saver Rinse
1 times

Overflow Rinse 2 times

Overflow Rinse 2 times

Water Saver Rinse
2 times

● Possible the total time is not same due to different water pressure.

● Shower rinse could be changed as Water Saver Rinse .
Please see Page 15 instructions SHOWER RINSE.

HOW TO USE THE CUSTOMIZED COURSEHOW TO USE THE CUSTOMIZED COURSE

You can set WASH, RINSE, SPIN and adjust operating time freely according to your habit
or laundry.

Procedure

(The number means times,“ ”Means
Overflow Rinse ).

0 1 1 2 2 … … 4 40 1 1 2 2 … … 4 4

634 12

● Make sure that nothing remained in pocket. (Pin, coin or something like possibly
damage clothes or washing machine, and the extra noise occurred may cause
trouble to washing machine).

● Overturn the clothes to get rid of scraps.

● Wool items like women underwear, articles with embroider, nylon etc, should be
placed in a laundry net for extra protection.

● Close the fastener and tie loose laces.

● Brush the dirty parts like dust, sand.

● Put light clothes down. Please pause operation and push it into water
when it floats up.

● Please separate washing white clothes from coloured clothes, coats from underwear.

THE PREPARATION OF LAUNDRY BEFORE WASHINGTHE PREPARATION OF LAUNDRY BEFORE WASHING

Water Saver Rinse
2 times

1 31 3

1 41 4

11

22

33

HOW TO USE PRESET WASHING HOW TO USE PRESET WASHING

·The preset time means the ending time of washing.

·Before using Preset Washing, please make sure of opening water supply, drain hose to

avoid water leakage.

1.Press POWER ON/OFF button .

2.Select COURSE or PROCESS as needed.

3.Press the PRESET button to select the time of ending.

4.Select water level if necessary.

·Putting detergents.

5.Close the washer lid.

6.Press the START/PAUSE button.

·After the PRESET is started, the corresponding light will be turned on, and
other lights get turned off around one minute latter.

·Preset function could not be used for DELICATE course.

·To check the Preset procedure, please press PRESET button, the procedure
will be indicated for 5 seconds.

·To cancel the preset, please shut off the power.

·To change the preset time, please re-preset after cancel of it.

THREE TYPES OF RINSETHREE TYPES OF RINSE

1.Water Saver Rinse(Normal)

2.Shower Rinse(Water Saving)

3.Overflow Rinse(with excessive detergents)

When spin finished, water is added
to the level setting and the washer
starts rinsing.

The Wash/Spin tub will start rotating slowly
while water is added like shower. The water
continuous to drain during this cycle.

Water is added to the level setting after spinning,
then the washer starts rinsing. During this operation,
the water still is added continuously to overflow the
foam with detergents.

VARIOUS FUNCTIONSVARIOUS FUNCTIONS

ULTRASONIC FUNCTIONULTRASONIC FUNCTION

When select ULTRASONIC function, the light of ULTRASONIC is flashes. The washer
will brings Ultrasonic during working, and this helps more clean washing and saving
detergents.

·Please use less detergents or wash powder when select ULTRASONIC function.

·Cancel method of ULTRASONIC function: Press POWER ON/OFF button to switch on

the power, and press WASH button for 4 seconds till a sound from buzzer. To restore it,
repeat above or pull out the plug.

MULTIPLE WATER POWER FUNCTION MULTIPLE WATER POWER FUNCTION

Press WATER POWER button to adjust water current during washing or rinsing. Press it
once more, the digital indicates “ H0 (standard water power), H1, H2, H3, H4, ( stronger.
H4 is the strongest); L1, L2, L3, L4 (weaker, L4 is the weakest).
And this function could not be set for DELICATE or BLANKET program.

HOW TO USE DETERGENT WHEN PRESET WASHHOW TO USE DETERGENT WHEN PRESET WASH

·You can put powder detergent directly to Detergent Tray or put it directly to wash
tub wrapped with handkerchief.

·Pour liquid detergent or bleach to the hole on pulsator. Do not pour it directly to
laundry, otherwise possibly cause depigmentation.

·Dilute the Softener with twice water, pour it into Softener Dispenser on the balance
ring.

·Do not use Soap since it is difficult soluble.

Procedure

1 51 5

1 61 6

When select NORMAL, CUSTOM or H EAVY DUTY, 15 seco nds af ter st arti ng, th e
machine will remember this program and starts same next time working.

PRESET and WATER LE VEL will not be remembered.

The Soak, Wash , Rins e and Sp in for C USTOM program could be remembered.

●This function is not available for DELICATE/BL ANKE T cours e.

●

●

●The memory will be lost if pull out the plug.

WATER LEVEL SETTINGWATER LEVEL SETTING

Washing with low level water and rinsing with high level water will help more clean
washing and completely rinsing.

Method of setting

Method of setting

Press WASH but ton to s et was h time , pres s WATER LEVE L button to set water level
for wash, press RINSE button to set rinse type and rinse times. Then pr ess
WATER LEVEL to set wat er lev el for r inse , pres s SPIN b utto n to set s pin ti me, pr ess
START/PAUSE button to start. By this, wash and rinse will work according to the water
levels set separately.

TWO CLEAN STEPS FUNCTIONTWO CLEAN STEPS FUNCTION

The washer will start washing when water to the level below 2 levels as set. By this,
the washer starts working with more density of detergent.

·This function won't be effect ed whe n sele ct lev el 1 or le vel 2 wa ter, and D ELIC ATE
or BLANKET co urse .

·When SOAK is selected, this function will not be effect ed aft er soa king .

SHOWER RINSESHOWER RINSE

Under NORMAL, if set 2 times rinses, the first rinse will be shower rinse. If you don't
want shower rinse, you can cancel it and it will change to Wat er Sav er Rin se or
Overflow Rinse.

Press POWER ON/OFF button to switch on the power, and press RINSE button for 4
seconds till a sound from buzzer. To restore it , repe at abo ve or pu ll out t he plu g.

Method of setting

Method of setting

HOW TO DRAIN REMAINING WATERHOW TO DRAIN REMAINING WATER

When select this function, in 9 minutes after the working finished, the drainage valve will
open to drain out the remained water inside. This will avoid freezing inside and applicable
in winter when temperature below 0℃.

Press POWER ON/OFF button to switch on the power, and press SOAK button for 4
seconds till a sound from buzzer. To restore it , repe at abo ve or pu ll out t he plu g.

CHILD LOCK FUNCTIONCHILD LOCK FUNCTION

This function avoids child open the washer.

Press POWER ON/OFF button to switch on the power, and press WATER LEVEL
button for 4 seconds till a sound from buzzer. To restore it, repeat above or pull out
the plug.

·When CHILD LOCK was set, the CHILD LOCK on control panel lights,
and indicates E5 and buzzes if washer lid open for 5 seconds during washing.

PROCESS CHANGINGPROCESS CHANGING

The process no started could be changed during working. No need to switch off the
power to re-set the function. For example, you can change rinse times during washing
directly.

DELETE THE END BUZZERDELETE THE END BUZZER

If select this function, the buzzer will not sound at the end of working. Thi s is
suitable for washing clothes at night.

Press POWER ON/OFF button to switch on the power, and press START/PAUSE
button for 4 seconds till a sound from buzzer. To restore it, repeat above or pull out
the plug.

Method Of Deletion

VARIOUS FUNCTIONSVARIOUS FUNCTIONS VARIOUS FUNCTIONSVARIOUS FUNCTIONS

REMEMBER FUNCTIONREMEMBER FUNCTION

CYCLONE DRYCYCLONE DRY

Method of setting: Press POWER ON/OFF button to switch on the power, and press

SPIN button for 4 seconds till a sound from buzzer. To restore it, repeat above or pull
out the plug.

Clean washing machine

Use soft clothing to wipe off the water or
dirt on the surface of the washer.

● Detergent, propellant and other
chemicals are not allowed to use
to avoid the damages
on the surface.

● Do not spray water
directly to the washer
body.

1.During Washing or Rinsing, still there is Water inletting. This is possibly automatic water
adding due to water level decrease.

2.Spin tub turns or stops timely at the beginning of spinning. This is intermittent spinning
for better spin effect.

3.No drainage during overflow rinse. This is caused by lower water level set or lower
water pressure.

4.Water inletting and rinsing sometimes during spinning. This is automatic lean-correction
due to clothe is not equally inside.

5.There is sound like water flow after spinning. This is the sound of balance liquid in
Balance ring. It is for reducing vibration of spinning.

6.Control panel keeps warm after power off, this is caused by Remembering circuitry
working.

7.Power off during working and the washer could not continue working. Should set the
program again.

NO TROUBLE CONDITIONSNO TROUBLE CONDITIONS

TROUBLE SHOOTING GUIDETROUBLE SHOOTING GUIDE

Trouble Indication

When the following problems occur,the microcomputer will detect the abnormal condition
and an electronic buzzer sounds for approximately 10 seconds and the indicators flash as
shown below. At the same time,the washer stops operation.

Kind o f
Troub le

Troub le
Indi catio n

Wher e to Chec k

The wa sh er
does n ot w or k
at all .

Press the POWER ON/OFF button.
Press the START/PAUSE button.
Press the PRESET button.
Check whether power failure occurs.
Check whether the fuse or circuit breaker has
been activated.

Water does not
flow into the
Wash/Spin Tub.

Water does not
drain out.

The washer
does not spin.

The buzzer
keeps beeping.

Other troubles.

Close the Washer Lid.

Check whether the CHILD LOCK is set.
Close the Washer Lid.

Turn the water supply faucet on.
Check whether the water supply has been cut off.
Check whether the metal filter of the Water Inlet
is clogged.
Check the washer has been freezing.

water pressure is too low.Check whether

Put down the Drain Hose from the hookhole.
Check the Drain Hose for any obstructions.
Check whether the Drain Hose is clogged.
Check whether the Drain Hose rises too high off
the ground.

Check whether the laundry is clumped on one
side of the Wash/Spin Tub.
Check whether the washer is on the level surface.

Press the POWER ON/OFF button to turn off the
power, call your service-person or dealer.

NOTE: The trouble indicators can be released by pressing the START/PAUSE button
once if you want to release the emergency stop.
Then press the START/PAUSE button again to restart the operation.

Filter

Water Inlet

If a malfunction should occur during the washer operation,first check the
following items before calling a service-person or dealer.

WARNINGWARNING

1 71 7

1 81 8

Below introducing how to maintain the washing machineBelow introducing how to maintain the washing machine

Clean lint filter

(Suggest clean it every week)

1.Take out the lint filter.

2.Pull out the scraps and wash
the lint filter in the water.

3.Install the Filter ( aim the
frame claw to the groove
below).
( Lint Filer is easy destroyed
parts).

Clean “ magic ” hose joint filter

“ Magic ” Hose

Joint filter

“ Magic ”

Hose Joint filter

(Suggest clean it every 6 months)

1.Pull the water inlet hose out.

2.Turn off the revolver
according to below photo.

3.Load off the

and clean the crud

with a toothbrush.

4.Install the clean

to revolver

and water inlet hose

Clean the water inlet Valve

(Suggest clean it every 6 months)

After long time use, the water inlet
mesh bag may be blocked with
crud, please load off the water
inlet hose, take out the water
inlet mesh bag from the water
inlet valve, clean the mesh bag,
then assemble the mesh bag in
the valve and load the water
inlet hose.

CARE AND MAINTENANCECARE AND MAINTENANCE