Sanyo 14GX37, IIC Service Manual

SERVICE MANUAL

f

-------------------------------------------------------------------------------------------------------

SANYO IIC CHASSIS

PAL/SECAM/NTSC(AV)
COLOR TV RECEIVER

For user's safety (to meet the safety requirements o
some countries), the receiver should be kept in its initial
status. Only same spare parts can be replaced with.

Contents Page

 Specifications………………………………………………………………………
 Remarks……………………………………………………………………………
 Description of new circuit …………………………………………………………
 Maintenance adjustment……………………………………………………………
 Trouble shooting……………………………………………………………………
 Chassis circuit diagram ……………………………………………………………
 Block diagram………………………………………………………………………
 Replaceable parts list ………………………………………………………………

WARNING

Some parts of the receiver are charged. Separate transformer must be used between the mains plug and the

socket when repairing the chassis.

To prevent electric shock, do not remove the outer cover. No user serviceable parts inside. Please refer

servicing to qualified service personnel.

SPECIFICATIONS

f

r

r

Aerial impedance ………………………………………………………75Ωunbalanced
Convergence……………………………………………………………Auto focus system
Focus……………………………………………………………………Double high level static focus
Rated audio output frequency …………………………………………Max 3W×2
Picture carrier frequency ………………………………………………38MHZ
Sound carrier frequency ………………………………………………31.5MHZ
Power supply …………………………………………………………AC 135~240V 60HZ/50HZ
Power consumption……………………………………………………75W
Loudspeaker ……………………………………………………………Round loudspeaker
scanning deflection ……………………………………………………Magnetic deflection
Tuning range……………………………………………………………

REMARKS

Please refer maintenance and servicing to qualified service personnel.

High voltage system and picture tube

When repairing high voltage system, an insulation line (such as a probe) must be
connected to a 10Ωresistant in series between the metallic part(ground ) and the second stage o
the picture tube to eliminate the static electricity of the high voltage system.The AC mains
plug must be separated from the AC power supply.

1The picture tube of the receiver adapts integrated inner anti-explosion.
2For safety continuity, only tube of the same model can be used for replacement.
3Do not lift the tube by its neck.
4The picture tube can't be dealt with until the anti-shock screen is worn and the high voltage
system is discharged thoroughly.

X-ray

This receiver is designed to keep the X radiation to absolute minimum. Yet malfunction o
servicing might cause the danger of exposing sealed areas to excessive radiation. Therefore the
precautions below must be followed:
1During servicing, never let the high voltage of the receiver exceed 28KVI=0uA
2The high voltage must be kept at 25.5KV±1.5KVI=1000 uAso that the receiver can operate
normally. The receiver has been set to the said high voltage before leaving the factory.
 After servicing, high voltage fluctuation may occur. Be sure to examine whether the high
voltage fluctuates or not after servicing.
3Do not replace with unauthorized picture tube in case of excessive X radiation.

Before return

Before returning the receiver to its user, please go through the following safety examinations:
1Check all the insulation of the wires between the chassis and the other metallic parts of the
receiver. Make sure that no insulation damage or short contact occurs.

2Check all the protection devices, such as non-metallic control buttons, tuners on the rea

cover ; etc.

Description of new circuit

1. Definitions of Ports

11 LC863328A-5W63 pins diagram

1 UHF (VLF) BAND1 42
2 50/60 (VHF) BAND2 41
3 ALARM LNA 40
4 WOOFER VOL AV1 39
5 VOLUME-L AV2 38
6 VOLUME-R MUTE 37
7 POWER WOOF ON/OFF 36
8 VT SIF 35
9 GND IR 34
10 XTAL1 SD 33
11 XTAL2 S-VHS 32
12 VDD ENABLE 31
13 KEY IN SCL1 30
14 AFT IN SDA1 29
15 NC SCL0 28
16 AC DETECT SDA0 27
17 RESET NC 26
18 FILT BLANK 25
19 CHROMA B OUT 24
20 V-SYNC G OUT 23
21 H-SYNC R OUT 22

12 CPU ports description

pin Port usage Function description

1 P10/SO0 UHF Select UHF (BAND OPTION select "2" or "3")
2 P11/SI0 50/60 Horizontal frequency 50/60 output
3 P12/SCK0 ALARM Alarm signal output
4 P13/PWM1 WOOFER VOL Woofer volume PWM output
5 P14/PWM2 VOLUME-L Volume-L PWM output port
6 P15/PWM3 VOLUME-R Volume-R PWM output port
7 P16 POWER POWER ON/OFF signal output control port
8 P17/PWM VT Tuning-use 14bit PWM output port
9 VSS GND Ground
10 XT1 XTAL1 CPU use crystal oscillation port
11 XT2 XTAL2 CPU use crystal oscillation port
12 VDD VDD Power supply (+5V)
13 P84/AN4 KEY IN Key in port
14 P85/AN5 AFT IN AFT signal input port
15 P86/AN6 NC Not connected
16 P87/AN7 NC Not connected
17 RESET RESET CPU reset port
18 FILT FILT OSD filtering
19 P83/AN3 CHROMA SECAM chroma detection
20 VS V-SYNC Vertical pulse input
21 HS H-SYNC Horizontal pulse input
22 R R OUT OSD red signal output
23 G G OUT OSD green signal output
24 B B OUT OSD blue signal output
25 BL BLANK OSD blanking signal output
26 I NC Not used
27 P60/SDA0 SDA0 IIC data(EEPROM use)
28 P61/SCLK0 SCL0 IIC clock(EEPROM use)
29 P62/SDA1 SDA1 IIC data( other IC use)
30 P63/SCLK1 SCL1 IIC clock (other IC use)
31 P70/INT0 ENABLE Automatic adjustment enabling port
32 P71/INT1 S-VHS S-VIDEO detection
33 P72/INT2 SD SD input port
34 P73/INT3 IR Remote control signal input
35 P00 SIF 4.5M sound absorption selection
36 P01 WOOF ON/OFF Woofer on/off
37 P02 MUTE MUTE control
38 P03 AV2 AV option control port 2
39 P04 AV1 AV option control port 1
40 P05 LNA Sensitivity control port
41 P06 BAND2(VHF) Band option
42 P07 BAND1(VLF) Band option

1-3.Description of port-controlled output modes
notein the tables below, "0" refers to low level"1" refers to high

level.
1-3-1.Power switch control

Port POWER ON POWER OFF
Pin7(POWER) 0 1

1-3-2. Band control

BAND

OPTION=0

Port V-L V-H UHF V-L V-H UHF V-L V-H UHF V-L V-H UHF

Pin42(BAND1) 0 1 1 0 1 1 1 0 0 0 1 1
Pin41(BAND2) 0 0 1 1 0 1 0 1 0 1 0 1
Pin1(UHF) x x x x x x 0 0 1 1 1 0

BAND
OPTION=1

BAND OPTION=2 BAND

OPTION=3

BAND OPTION LA7910 TUNER PORT/H POTR/L
Port V-L V-H UHF V-L V-H UHF V-L V-H UHF V-L V-H UHF

Pin42(BAND1) 0 1 1 0 1 1 1 0 0 0 1 1
Pin41(BAND2) 0 0 1 1 0 1 0 1 0 1 0 1
Pin1(UHF) x x x x x x 0 0 1 1 1 0

1-3-3. AV control

a). One-way AV

b). Two-way AV

PORT TV AV1 AV2
Pin39(AV1) 0 0 1
Pin38(AV2) 0 1 1

c). Three-way AV

PORT TV AV1 AV2 AV3
Pin39(AV1) 0 1 0 1
Pin38(AV2) 0 0 1 1

PORT TV AV
Pin39(AV1) 0 1
Pin38(AV2) 0 1

1-3-4. 50/60 output

PORT 50 60
Pin2(50/60) 0 1

1-3-5. Woofer functionwhen stereo control TA1216AN IC is employedTA1216AN

is provided with woofer control function. If TA1216AN is not used, CPU will
reserve a woofer port to enable woofer control function. Pin36 is used as on/off
control, and Pin4 as woofer volume control output.

PORT WOOFER ON WOOFER OFF
Pin36(WOOFER) 0 1

1-3-6. L/R volumewhen stereo control IC is not used, simple stereo function can be
selected. Then Pin5 and Pin6 of the CPU can be used as L/R volume output control.

1-3-7. Sensitive receiving output control: in "SETUP" mode, if "SENSITIVITY" is
set to "1", then the function of controlling sensitive receiving tuner is selected, Pin40
is used as control output.

PORT SENSITIVITY(YUV) ON SENSITIVITY(YUV) OFF

Pin40 1 0

1-3-8. Mute control

a). POWER ON/OFF:
POWER OFF POWER ON POWER
OFF
POWER OUT: H L H

MUTE OUT: H L H

b). Besides, MUTE pin also operates when CPU is in automatic mute status or

when the MUTE button on remote control unit is pressed to make CPU
operate in mute status.

2. Automatic identification

2-1. Maximum channels to be stored

CPU can automatically determine the maximum channels to be stored according
to the capacity of external EEPROM connected.

EEPROM model AT24C02 AT24C04 AT24C08

Channel max 55 140 255

3. Definitions of Local Buttons

3-1. Definitions of buttons (AD input port)

PORT VOLTAGE RANGE BUTTON FUNCTION DESCRIPTION

AN4 0V~3/32VDD OFF No status when button pressed

KEY IN 4/32VDD~7/32VDD AUTO Full-auto search

8/32VDD~11/32VDD TV/AV TV/AV switch
12/32VDD~15/32VDD MENU Menu button
16/32VDD~19/32VDD VOL+ Volume +
20/32VDD~23/32VDD VOL- Volume ­ 24/32VDD~27/32VDD POS+ Program +
28/32VDD~VDD POS- Program -

noteif a local button and a remote control button are pressed simultaneously, the

local button is prior to remote control button.

3-2. Definitions of user's remote control buttons

Button English name Chinese name Function description Remark

0 0 0

Channels selected directly by

figure button

9 9 9

10

11 TV/AV TV/AV TV/AV switch
12 GAME
13
14 MENU
15 WOOF
16 VOL+ + Volume +
17 PROD
18 POWER
19 POS+ + Program +
20 VOL- - Volume -
21 JUMP Analogue jump (jump button in FACTORY mode)
22 MUTE
23 POS- - Program -
24 SLEEP /
25 PP / Picture mode selection
26 RECALL /
27 DISPLAY /
28 PICTURE / Picture menu
29 AUDIO / Audio menu
30 CLOCK / Clock menu/jump to yellow fast

31 SYSTEM / System menu / jump to cyan fast

 

















Direct selection by double or
triple digit numbers

GAME control

Control menu switch
Woofer switch control

Factory mode Factory use only
Power on/off

Mute

Sleep

Program recall
Display

page

page

3-3User's remote control unit wiring

VCC
N1

PIN1 PIN4PIN2 PIN3

LC7461M-8103

1 C3 24
2 C2 23
3 C1 22
VCC 4 C0 21
5 C4 20
6 C5 19
7 18
VCC 8 17
9 16

10 15
11 14
G1 12 13

C1 C2

PIN20

PIN19

PIN18

PIN17

PIN16

PIN15

8

GAME

VOL-

9

PROD POWER VOL+

JUMP

-/--/---

MUTE

3 1 2 0

7 5 6 4

TV/AV

WOOF MENU

POS+

POS-

C3 VD1

R1
R2 V1

PIN14

PIN13

SLEEP

PICTURE

P.P

AUDIO OPTION

RECALL

1. N1 LC7461M-8103 2. VD1 IR-LED

3. V1 2SC1815 4. R1 RT14-1/4W-1Ω-J

DISPLAY

SYSTEM

5. R2 RT14-1/4W-220Ω-J 6. C1 C2 CT1-05B-2B4-63V-220PF-K

7. C3CD110X-6.3V-100UF-M

8. G1 455KHZ 9.VCC 2 AA size batteries
User's code:
C5 C4 C3 C2 C1 C0

0 1 1 1 0 0

4. Button Functions and Operation Instructions

41 POWER (remote control button)

1) Functionpower on/off control

2) Description

Each press of the (POWER) button makes a switch between POWER ON and

OFF.

After power is turned on, CPU will read the data in EEPROM. CPU will

determine the POWER status according to the selection of "POWER
OPT"if "0" is selectedthen the POWER is always in POWER OFF status
after turn-onif "1" is selected, then the POWER status will be determined
according to the memory before turn-off.

In POWER OFF mode, only POWER button works. The other buttons do not

work. But the local POS+ and POS- buttons can be used to turn on the TV

set instead of POWER button.
SLEEP and TIME-OFF settings will be cancelled when "POWER OFF" is set.
If SCREEN OPT is set, then screen function is enabled during POWER

ON/OFF.

3) Output control
Please refer to description"1" in "2-3" section.

4) OSD display (about 10 seconds)

12
AUTO
D/K

42 TV/AV remote control button, local button

1) FunctionAV-TV switch.

2) Description
Each press of this button makes one switch between TV and AV.
Auto mute and black background functions are enabled during the switch.
In AV modenumeric buttons (09), (- -), POS and POS buttons do not

work, only "AV" display appears.

If the last AV is switched to, and when S-VIDEO INPUT is detected by CPU,

the S-VIDEO control will be enabled automatically, and OSD display will
also be replaced by S-VIDEO display.

3) Output control

Please refer to description "1" in "2-3" section.

4) OSD displayabout 5 seconds

12 AV
AUTO AUTO
D/K

press TV/AV button

43. 09,remote control buttons

1) Functions select position directly.

2) Description

Press numeric buttons (0~9) to select programs in 0~9 positions directly. Press

---button to enter into two-digit or three-digit figure mode before selecting
programs in 10~254 positions (max programs is determined by the capacity
of EEPROM), then press (0~9) to key in figures in the order of hundred's,

ten's and unit's place to select programs directly.
The button does not work if the number is beyond the position max.
Auto mute and black background function are enabled during position switch.
When position selection is finished the current position and the last position will

change accordingly. The result will be written in EEPROM.
If the position selected is the same as the current position, CPU will re- read the

EEPROM about the information related to the current position.
In PRESET menupress (0~9) and(--) buttons to select directly the position to be

readjusted.
In CLOCK menu, press (0~9) and (--) buttons to preset program positions

directly.

In CHANNEL menupress (0~9) and (--) buttons to select the positions to be

copied.
In AV modepress (09) or (- -) buttons do not work, but AV display will appear.
During B/W balance adjustment in one light line mode, press numeric buttons

(0~7) can adjust sub-brightness, red bias, green bias and blue bias. "8", "9"

and "--" buttons do not work.

3) OSD displayabout 5 seconds

2 2
AUTO
D/K

notewaiting for the unit's digit

44. POS , POS/+, -remote control, local buttons

1) Function
move program position upward or downward by 1select options in a menu
select adjusting optionsplay games.

2) Description

Press POS/POSto change program positions. Automatically skip off the

position of "REMEMBER OFF".

Press and hold this button for more than 1second, the position will increase or

decrease by 1 for each 800ms.

If all program positions are in "MEMORY OFF " status, then press POS and

POS buttons can only select the program in "0" position. If only one
position is in MEMORY ON" status, then press POSPOS buttons can
select the only program in the position of "MEMORY ON".

After reaching the maximum position stored, press the POS button again will

return to the minimum position stored After reaching the minimum
position stored, press the POS button again will return to the maximum
position stored.

After switch is finished, the information of the current position and the last

position will change. The result will be stored in EEPROM automatically.
Auto mute and black background functions are enabled during program switch.
In full-screen menu, POSand POS buttons are used to select from top to

down the options in the menu (please refer to the operation instruction in

relevant menu.
In "B/W ADJUST", "ADJUST" and "SETUP" modePOS+ and POS- buttons

are used to turn page up and down.
In AV mode, press POS or POS button doesn't workbut "AV" display

will appear.
While checking perpetual calendar, press POS+ and POS- buttons to change

year.
In "Tetris" game, press POS+ button to rotate, press POS- to quicken fall. This

two buttons do not work in other games.

3) OSD displayabout 5 seconds

10 POS 11

AUTO AUTO
D/K D/K

POS

45 RECALL remote control button

1) FunctionTo recall the last program; play games .

2) Description: When switch is finished, the information of the current position
and the last position will change and the result will be stored in EEPROM
automatically.

In"888" and "Car racing " games, this button is used to play games, while in

"Tetris" game, this button is used to pause the game.

3) OSD displaysame as position OSD display

46. DISPLAYremote control button

1) FunctionProgram position displayincluding AV mode; to quit game.

2) Description

Press this buttonOSD will display program position, color system, sound

system, and will display position only in small characters after 5 seconds.
In AV mode, OSD will not display sound system .

In "B/W BALANCE" modethis button does not work during adjusting options

display; while in other OSD status, press this button will return to the
adjusting options OSD.

In "ADJUST" mode, this button does not work during adjusting options OSD

status, while in other OSD display, press this button will return to the
adjusting options OSD display.

In "SETUP" modethis button does not work during setting options display

status; while in other OSD display status, press this button will return to
the setting options OSD status.

If there is OSD display already (besides "B/W BALANCE" mode OSD,

"ADJUST" mode OSD, "SETUP" mode OSD and set PROD mode, bus in
OFF mode and mute OSD)press this button to cancel current OSD.

In game mode, press this button to exit.

3). OSD display (about 5 seconds)

Same as program position OSD display.

47. VOLVOLremote control , local button

1)Functionto control volume; adjust options; readjust settings and adjusting

options and play games.

2) Description:
When it is used to control volume output, each press of the button will

increase/decrease output by one step (the output is divided into 100 steps).

Press and hold the button for over 500ms  then the output will

increase/decrease one step for each 160ms.

When output reaches 100, press VOL again will not workif the output

reaches 0then press VOL will not work. In MUTE mode, press this
button can change the volume output, but press VOL- button can not

cancel mute status, while press VOL+ can cancel mute status.
In semi-auto search mode, press this two buttons can change search direction.
To adjust options in menus, or to start operation, or to go to the OSD display at

the next level.
To readjust month when checking the perpetual calendar.
To adjust setting options and adjusting options in "B/W BALANCE" mode,

"ADJUST" mode and "SETUP" mode.
When playing "Tetris", press VOL+ to move right. Press VOL- to move left. In

other two games, this two buttons don't work.

3) OSD display (about 5 seconds)

VOLUME
07

48 MUTEremote control button

1) Functionmutebright line-to-full screen switch.

2) DescriptionPress MUTE button to enter into mute status, press again to
cancel.

Press POWER and VOL buttons can also cancel mute status.
In mute status, mute OSD will be on display if there is no other OSD display

(in "FACTORY" and BUS OFF mode, "FACTORY" and "BUS OPEN"
OSD and MUTE OSD can display on the screen at the same time.

In "B/W BALANCE" modeMUTE button is used to switch between normal

status and a line status. If the "LINE MODE" on menu3 is "1"the full­screen is switched to a light line and the picture status will automatically
turn to "FACTORY1 modewhen the light line is switched to full screen,
the picture status will automatically turn to FACTORY 2 mode. If "LINE
MODE" is "0"the picture status will not change during full screen-to-light
line switch.

3) OSD display (after 5 seconds turns to one line and keeps on displaying)

MUTE

07 MUTE

49 WOOFremote control button

1) Functionselect/cancel woofer mode

2) DescriptionPress WOOF button to control WOOF switch.

When in WOOF OSD, and WOOFER ON status, if "WOOF VOL.OPT" is set

to "1"WOOF VOLUME will appear. Use VOL+ and VOL- to change the
woofer output volume.

If woofer function is not selected, then just cancel the relevant button on the

remote control unit.

Output mode

There are two output modes, output through TA1216AN and CPU

respectively please refer to descriptions in "2-3" section.

3) OSD display (about 5 seconds)

WOOF ON WOOF OFF

WOOF button

WOOF VOLUME

50

4-10 MENUlocal button

1) Functionenter into PICTURE, AUDIO, SYSTEM, CLOCK, PRESET and
CHANNEL menu.

2) Description

Press MENU button to change as follows

none CHANNEL menu PRESET menu

PICTURE menu AUDIO menu SYSTEM menu CLOCK menu

PRESET menu operation instruction:

When OSD display is neither one of those of PICTURE, AUDIO, SYSTEM,

CLOCK, PRESET or CHANNEL menupress MENU buttonthe OSD of
PICTURE menu will display first.

In AV mode, neither PRESET nor CHANNEL menu will turn up in the cycle

when MENU button is pressed.

If stereo control function is not selected, AUDIO menu will not appear in the

cycle.

3) PRESET menu operation instruction

After finding the PRESET menupress POS/POS- to select. The options

with an arrow are currently selected ones. The other options are in green.

Press VOL and VOL buttons to change setting values and to start. During

fine adjustment and semi-auto search, press VOL to move upward and

press VOL button to move downward.

In PRESET menu, press figure buttons (0~9) and (--) button to select the

program position to be adjusted directly.

During fine adjustment and semi-auto search, the color of OSD display bar will

turn to red, and the small erect bar displaying PWM setting values will
turn into an arrow indicating direction. When the operation is finished or
paused, the OSD display bar will turn to green.

During semi-auto search, search will stop when a program position is searched.

During semi-auto search, press VOL+ or VOL- button to change search

direction; press MENU button to stop search.
During auto-search, press MENU button to stop searching.
The modification of setting values will be automatically stored in EEPROM

addresses corresponding to program positions.
When auto-search is completed, the color system of the program positions

stored is set to AUTOthe sound system is the same as that of the position

before auto-search.
If the position of a certain program is set to REMEMBER OFFthis position

will be skipped off when POS/POS is used to change positions. If "--"

button or "0~9" buttons are used to select the REMEMBER OFF position

directly, its position display will become red for distinguishing.
If a program position is fine adjusted, then the automatic digital AFT will be

off automatically. When the fine adjusted position is selected, its position

display will turn to yellow for distinguishing.
If no operation is performed within ten seconds, the PRESET menu will quit

automatically.

4) PRESET menu OSD display (about ten seconds)

PRESET

POSITION 0
REMEMBER OFF
BAND VL
FINE
SEMI SEARCH
AUTO SEARCH

5). CHANNEL menu operation instruction
Press MENU button to reach CHANNEL menu. Press POS+/ POS- button to

select options upward and downward. The option selected will be indicated

with an arrow and its OSD display will become red. The OSD display of
the options not selected is in green.

"EXCHANGE" is to exchange the memory information of the current channel

with that of the target channel; "CLEAR ALL" is to close all the memory
of position storing channel information, that means no program is stored.

When "EXCHANGE" is selectedthe position displayed first is the current

position. Key in position with "--" and "0~9" buttons and press VOL+ or
VOL- to start. After exchange is finished, channel menu will quit
automatically. The program played by the current position will
automatically become the program directed by the memory information of
the former target position.

If "CLEAR ALL" is selected, press and hold VOL+ or VOL- button for 2

seconds to start. During the operation, OSD display will show 
"CLEARING ALL…" for attention. When CLEAR ALL is completed,
program position will jump to "0" automatically.

If no operation is performed within 1o seconds, CHANNEL menu will quit

automatically.

6). CHANNEL menu OSD display (about 10 seconds)

CHANNEL

EXCHANGE 10 ­ CLEAR ALL

4-11. AUTO (local button)

1). Functionto start auto-search mode directly.

2). Instruction
Press AUTO button to start auto-search mode directly.
In auto-search mode, press MENU or AUTO button to stop auto-search.
When auto-search is finished, the picture status will be set to STANDARD

automatically, and the sound output is set to"15".

During auto-search, the positions searched will be stored in EEPROM

automatically from position"0". When the amount of programs searched
exceeds the max position allowed, auto-search will stop. If the amount
of programs searched do not reach the max position allowed, the
program positions not stored will be set to "REMEMBER OFF " after

auto-search is completed.

412 PICTUREremote control button

1) Function to enter into PICTURE menu.

2) Description
After reaching the PICTURE menupress PICTURE button to select, or press

POS/POS to select options upward /downward. The option with an arrow is
the currently selected option. Its OSD is in red. The other options are in green.

Press VOL or VOL to increase or decrease the output values of relevant

options. The bar-like OSD and figures at the bottom of the screen indicate
the current output values of the relevant options. The output value of each
option is divided equally into 100 steps. When the output value of an
option selected is changed, the bar-like OSD will indicate its changing
direction with an arrow. Press VOL+ can increase output value until it
reaches the max (100). Press VOL can decrease the output value until it
reaches the minimum (0).

When the color system is set to AUTO and the input signal is NTSC or forced

NTSC with color, OSD will present TINT option. In other cases there is no
TINT option.

After the values in PICTURE menu are changed, the result will be stored in

EEPROM.

If no operation is performed within 10 seconds, PICTURE menu will quit

automatically.

3) OSD display (for about ten seconds)

PICTURE

BRIGHT 100
CONTRAST 100
COLOR 50
SHARP 50
TINT 00

413. PP remote control button

1) Functionto set different picture effects.

2) Description:
CPU 's ROM has four set picture effect modes----"STANDARD", "SOFT",

VIVID" and "LIGHT"that is to set corresponding brightness, contrast,
sharpness, chrominance and tint. Besides, the "PERSONAL" can be
adjusted as you like and be stored automatically into the EEPROM for use.

"FACTORY" and "B/W BALANCE" modes also provide "FACTORY1"and

"FACTORY2" modes as well as the above modes.

Press PP button to change in the following order

STANDARD SOFT VIVID LIGHT FACTORY1
(NORMAL mode)
MEMORY FACTORY2

("FACTORY" and "BALANCE" mode)

3). Output values

BRIGHT NESS CONTRAST CHROMINANCE SHARPNESS TINT

STANDARD 80 80 50 50 00

SOFT 70 40 60 25 00

VIVID 60 100 88 70 00

LIGHT 100 100 70 72 00
FACTORY1 00 00 00 00 00
FACTORY2 100 100 00 00 00

4). OSD display (about 5 seconds)

STANDARD

4-14.AUDIO (remote control button)

1). Function: enter into AUDIO menu.

2). Description:
If stereo function is not set or stored in EEPROM, then AUDIO button do not

work. If simple stereo is set, then "treble" and "bass" are not included in the
menu.

Press AUDIO to reach AUDIO menu. Press AUDIO to select options in circles,

or press POS+ or POS- to select upward and downward. The option
selected is pointed out by an arrow, and its OSD is red. The OSD of other
options not selected are green.

Press VOL or VOL to increase or decrease the output values of relevant

options. The output value of each option is divided equally into 100 steps.
Press VOL+ can increase output value until it reaches the max (100). Press
VOL can decrease the output value until it reaches the minimum (0).
When VOL+ or VOL- is used to change output values, a bar-like OSD at

the bottom of the screen will indicate its changing direction with an arrow.
The output values changed will be stored in EEPROM automatically.
If no operation is performed within 10 seconds, AUDIO menu will quit

automatically.

3). OSD display (about 10 seconds)

AUDIO

VOLUME 25
TREBLE 50
BASS 50
BALANCE 00

25

415 CLOCKremote control and local buttons

1) Functionto enter into CLOCK menu.

2) Description:
CLOCK menu operation description

Press CLOCK button to enter into CLOCK menu. If time is not set after

start-up, OSD display of the options is yellow. If time is set, then the
options are in green OSD display.

Use Clock button to select in circles or press POS/POS button to select

proper items upward or downward. The option selected will be pointed out
with an arrow, and its OSD display is red. (CLOCK must be set before
setting the options hereafter.)

Press VOL or VOL to change setting values. Use VOL to set minute,

and use VOL to set hour. Each press of VOL adds one minuteeach
press of VOL- adds one hour. Press VOL or VOL button and hold for

more than 500MSthen minute or hour will be added by one after each
160MS.

The cycle period of hour is 24 hoursand that of minute is 60 minutes. When

the hour is set to 23, press VOL- button again will clear the time setting.
Press once again will start from 0 again.

If OFF-TIME is setthe setting of SLEEP will be cancelled. Press POWER

button to set POWER OFF mode, the setting of OFF-TIME will be
cancelled automatically.

When setting time of ON-TIME comes and starts up the TV, SLEEP will be set

to 120m automatically in case there is nobody at home to turn off the TV
after its automatic start-up. Any operation after automatic start-up can
cancel the setting of SLEEP automatically.

If POSITION is setthe desired position will be entered into upon start-up at

the on-time or preset time.

If timer function is selected, the program on the "preset position" will start

automatically at the preset time.

If attention timer is set, "ATTENTION" in big red letters will be seen flashing

on the screen at the preset time until any button is pressed. During flashing
for attention, it is in automatic mute mode. If the output function of
ALARM port is selected, alarming will be heard.

If no operation is performed in ten minutes, the CLOCK menu will quit

automatically.

3). OSD display

TIME

CLOCK - - : - ­ OFF-TIME - - : - -

ON-TIME - - : - -
ATTENTION - - : - -

BESPOKE-TIME - - : - ­ BESPOKE POSITION -

ATTENTION

About 10 seconds note: flash for attention

4-16. SYSTEM (remote control unit)

1). Function: enter into SYSTEM menu.

2) Description:
Press SYSTEM button to reach SYSTEM menu. Press SYSTEM again to

select options in circles, or to press POS+ or POS- to select option upward
or downward. The option selected is pointed out by an arrow. Its OSD
display is red. The options not selected is in green OSD display.

Press VOL+ or VOL- to change setting of options. The result will be stored in

EEPROM automatically.

If single color system is set, the menu has no "COLOR-SYS" option. If single

sound system is selected or the system is in AV mode, the menu has no
"SOUND-SYS" option. If either ENGLISH, ARABIC or RUSSIAN mode
is selected, then the menu has no "LANGUAGE" option.

If SENSITIVITY is selected ( SENSITIVITY is set to "1")the menu has

"SENSITIVITY" option. Its mode is remembered separately like color
system, sound system. The auto mute function is enabled during sensitivity
mode modification.

If calendar function is selected( "CALENDAR" is set to "1") there is a

CALENDAR option. Select this option and press VOL+ or VOL- button to
enter into calendar OSD. Then press POS+ or POS- button to set yearand
use VOL+ or VOL- button to set month. The calendar covers 1000 years
from1600 to 2599.

If no operation is performed within10 seconds, SYSTEM menu will quit

automatically.

3). OSD display (about 10 seconds)

SYSTEM

COLOR-SYS AUTO
SOUND-SYS D/K
SENSITIVITY OFF
LANGUAGE ENG
CORING ON
CALENDAR

2000 JANUARY

SU MO TU WE TH FR SA

1
2 3 4 5 6 7 8
9 10 11 12 13 14 15
16 17 18 19 20 21 22
23 24 25 26 27 28 29
30 31

417 SLEEP (remote control button

1) Functionset sleep timekeep current page unchanged.

2) Description:
The maximum sleep time is 120 minutes. Every 15 minutes equals one step.
After sleep time is set, OFF-TIME is cancelled automatically.
When sleep time goes to the last minuteOSD will display information on

sleep time, reminding that the TV will be turned off.

3) OSD display (about 5 seconds)

SLEEP
60

418. GAMEremote control button

1) Function: to enter into/exit GAME mode.

2) Description:
GAME button works only when at least one game is selected. Three games are

available totally: "888", "Car racing" and "Tetris".

Use RECALL button to play "888" and "car racing" games. Use RECALL

button to pause in "Tetris".

POS+, POS-, VOL+ and VOL- work only in "Tetris" game. POS+ is used to

rotate or to restart when game is over. POS- is used for fast drop. VOL+ is
used to move right, and VOL- is used to move left.

In GAME mode, press either GAME or DISPLAY button to quit game.
In GAME mode, the function of auto-turnoff without signal will be cancelled.

Only the said control buttons and POWER button work in GAME mode.
Other buttons do not work.

Rules of "888": 3 same figures wins 5 gold coins; three sequential figures wins

4 gold coins; two of the three figures are"8" can win 3 gold coins; one of
the three figures is "8" wins 1 gold coin. No bonus in other cases.

Rules of racing; 3 players use "RECALL" button in turn to set their advancing

step. If the step is negative, the player retreats. The player who arrives at
the finish first is the winner.

Scoring in "Tetris"cancel one line at a time win 1 point, cancel 2 lines at one

time win 3 points, cancel three lines at a time wins 7 points.

419. PROD/FACTORY moderemote control button/factory use only

1) Functionenter into "FACTORY" mode, "B/W BALANCE" mode, "ADJUST"
mode and SETUP m ode.

2) Description

Press PROD button to change as follows

NORMAL FACTORY B/W BALANCE ADJUST

SETUP

After enter into "FACTORY" modethe function of blue background when no

signal is received and the function of automatic turnoff when no signal is
received within ten minutes will be cancelled, and automatic search speed
will be doubled. In B/W BALANCE mode, ADJUST mode and SETUP mode,
the function of blue background display without signal and the function of
auto-turnoff when no signal is received within ten minutes will be cancelled
automatically.

EEPROM will remember "FACTORY" mode. The other modes will not be

remembered, and will be automatically cancelled upon restart-up.
"FACTORY" mode is used during the aging process of production.

In "B/W BALANCE", "ADJUST" and "SETUP" mode, use "POS+" or "POS-"

to select adjusting options and setting options; use "VOL+" or "VOL-" to
change values.

5. Bus adjustment and setting options

5-1. Manual B/W balance adjustment

1). Operation instruction:
Press PROD button to enter into "B/W BALANCE" mode and the first

adjustable item "sub-brightness" will turn up then. The OSD display of the
B/W balance adjustment covers one line on the top to reserve the central
space for camera lighting.

Press POS+/POS- to turn pages to find adjusting options. If adjusting-use remote

control unit is employed, press a single button can jump directly to the items

to be adjusted.
Press VOL+ or VOL- button to adjust the selected item.
Repeat step b) and c) till a satisfactory result is reached. Press PROD button to

quit.

2). Table of adjustable items:

OSD

DISPLAY

S-BRI Sub Brightness Sub Brightness 0~127
R-BIA Red Bias Red Bias 0~255
G-BIA Green Bias Green Bias 0~255
B-BIA Blue Bias Blue Bias 0~255

R-DRV Red Drive Red Drive 0~127
G-DRV Green Drive Green Drive 0~15
B-DRV Blue Drive Blue Drive 0~127

C.B/W Cross B/W Internal signal 0~3

CORRESPONDING LA76810

BUS ITEMS

NAME RANGE VARIABLE

3). During maintenance, one light line can be used to adjust black balance roughly.
In "B/W BALANCE" modepress MUTE button to enter into one light line

modepress MUTE button again will return to full screen mode. In light
line mode the picture status will be set to "FACTORY1" modei.e., all the
output values on the picture menu are "0"When full screen returns, the
picture status will be set to "FACTORY2" mode, i.e., setting values of
brightness and contrast are "100" while the other settings in the picture
menu are "0".

In "LINE MODE", besides MUTE button, the following eight buttons on user's

remote control unit will work, with their functions changed as follows.
Other buttons will not work.

BUTTON 1 3 5 7

FUNCTION Sub brightness + Red bias + Green bias + Blue bias +

BUTTON 0 2 4 6

FUNCTION Sub brightness- Red bias - Green bias - Blue bias -

c) During production, factory use remote control unit can be used to speed up

adjustment. Please refer to 4-4 for button definitions.

2-2. The adjustment of adjusting options and setting options

1). Operation instruction:

. Press PROD button to enter into "ADJUST" or "SETUP" mode.
Press POS+/POS- button to turn page up/down to select the options to be

adjusted. If adjustment use remote control unit is used, some options can

be selected directly by pressing one single button.
. Press VOL+ or VOL- button to change the values of options selected.
. During production, factory use remote control unit can be used to speed up

adjustment. Please refer to 4-4 for button definitions.

2). Description on adjusting options

No. OSD display LA76810 bus data Name Range

0 H.PHASE H.PHASE Horizontal center 0~31
1 NT.H.PHASE H.PHASE NT horizontal center deviation -16~+15
2 H.BLK.LEFT Left blank 0~7
3 H.BLK.RIGHT Right blank 0~7
4 V.SIZE Vertical Size Vertical size 0~127
5 V.LINE Vertical Linearity Vertical linearity 0~31
6 V.POSI Vertical DC Vertical center 0~63
7 V.SC Vertical S-Correction Vertical S correction 0~31
8 NT.V.SIZE Vertical Size NT vertical size deviation -32~+31
9 NT.V.LINE Vertical Linearity NT vertical linearity deviation -16~+15

10 NT.V.POSI Vertical DC NT vertical center deviation -32~+31

11 NT.V.SC Vertical S-Correction NT vertical S-correction deviation -16~+15
12 RF .AGC RF AGC Delay HF AGC 0~63
13 SUB.CONT Contrast Sub-contrast 0~31
14 SUB.COLOR Color Sub-color 0~63
15 S.SHARP Sharpness Sub-sharpness 0~31
16 SUB.TINT Tint Sub-tint 0~63
17 VOL.OUT Volume Control Internal volume output 0~127
18 OSD CONT. OSD Contrast OSD contrast 0~127
19 OSD H.POSI OSD horizontal position 0~127
20 OSD V.POSI OSD vertical position 0~31

3). Description on setting options:
a). Part one

No. OSD display LA76810 bus data Name Range

0 BLK.STR.DEF Blk Str Def Black level

0/1

stretch definition
1 AFC GAIN AFC Gain AFC gain 0/1
2 V.SEPUP V.SEPUP Vertical

0/1
separation
sensitivity

3 CD.MODE Count Down Mode 0~7
4 DIGITAL OSD Digital OSD Digital OSD set 0/1
5 GRAY MOD Gray Mode 0/1
6 B.GAM.SEL B Select 0~3
7 RG.GAM.DEF RG Select 0/1
8 BRGHT ABL.TH Bright.Abl.Threshold 0~7

9 EMG.ABL.DEF Emg.Abl.Def 0/1
10 BRT.ABL.DEF Brt.Abl.Def 0/1
11 MID.STP.DEF Mid.Stp.Def 0/1
12 R-Y/B-Y G.BL R-Y/B-Y Gain

0~15

Balance
13 R-Y/B-Y ANG. R-Y/B-Y Angle 0~15
14 SECAM B-Y DC SECAM B-Y DC

0~15

Level

15 SECAM R-Y DC SECAM r-Y DC

0~15

Level
16 C.KILL.OFF C_Kill OFF 0/1
17 SND.TRAP Sound Trap 0~7
18 VOL.FIL Volume Filter Defeat 0/1
19 VIF.SYS.SW VIF.Sys.SW 0~3
20 VIDEO.LEVEL Video Level 0~7
21 FM.LEVEL FM Level 0~31

b). Part two

No. OSD display "0" mode "1" mode

22 POWER OPTION 0double start-up1memory2 or 3single start-up
23 POWER ON LOGO Power logo off Power logo on
24 SCREEN OPTION 0OFF1Screen on up start-up2Screen on upon turn-off 3Screen on upon

start-up/ turn-off

25 SCREEN TIME Black background time (0~7seconds)
26 SEARCH CHECK No "search check " function With "search check" function
27 BAND OPTION 0use LA79101use tuner with switch2 or 3CPU triple-port control
28 AV OPTION 0no AV1one-way AV input2two-way A V input3three-way AV input

29 LINE MODE No picture mode switch during FULL

SCREEN/LIGHT LINE switch

30 STEREO OPT Stereo off Stereo on
31 STEREO IC Stereo ICTA1216AN off Stereo ICTA1216AN on
32 WOOF VOL.OPT Woofer (headphone) volume control on Woofer (headphone) volume control off
33 SIF M/N 4.5M sound off 4.5M sound on
34 SIF B/G 5.5M sound off 5.5M sound on
35 SIF I 6.0M sound off 6.0M sound on
36 SIF D/K 6.5M sound off 6.5M sound on
37 PAL OPTION PAL color system off PAL color system on
38 N3.58 OPTION N3.58 color system off N3.58 color system on
39 N4.43 OPTION N4.43 color system off N4.43 color system on
40 SECAM OPTION SECAM color system off SECAM color system off
41 COLOR AUTO Auto color system off Auto color system on
42 ENGLISH OSD English OSD off English OSD on

43 RUSSIAN OSD Russian OSD off Russian OSD on
44 ARAB OSD Arabic OSD off Arabic OSD on
45 SENSITIVITY Sensitivity function off Sensitivity function on

With picture mode switch during FULL

SCREEN/LIGHT LINE switch

46 GAME1 OPTION Game "888" off Game "888" on
47 GAME2 OPTION Game "Car Racing" off Game "Car Racing" on
48 GAME3 OPTION Game "Tetris" off Game "Tetris" on
49 CALENDAR Calendar function off Calendar function on
50 V.MUTE OFF Video output off before POWER OFF Video output on before POWER OFF
51 BLUE/BLACK Blue background without signal Black background without signal

5-3. The application of factory use remote control unit

1). Description:
For products of the same batch, the selection of all setting options and part of the

adjusting modes of the products are same. Therefore it is enough to adjust only one
of the same batch as a standard sample. Take the EEPROM of the sample as source
EEPROM and copy it, then put the copies on the other products. By this means, the
setting options and that part of adjusting options of the other products do not need
to be adjusted, and the production can be speeded up considerably.

For items need or probably need to be adjusted, our software offers especially the

function of adjustment-use remote control unit o speed up production. Thus, in
B/W balance adjustment mode, the options can be adjusted directly through one
single button. In "ADJUST" mode, the option needs to be adjusted can be selected
through one single button.

2). Description on special-purpose remote control buttons:

a). "PROD/" has the same function as that of the "PROD/" button on

an ordinary remote control unit.

b). "ADJUP/ADJDOWN" is used to turn pages upward and downward. It

works only in "B/W BALANCE", "ADJUST" and "SETUP" mode. It has
the same function as what the ordinary remote control "POS+" / "POS-"
button has in "B/W BALANCE", "ADJUST" and "SETUP" mode.

c). "ADJ+/ADJ-" is used to increase/decrease adjustment of options selected.

It works only in "B/W BALANCE", "ADJUST" and "SETUP" mode. It
has the same function as what the ordinary remote control
"VOL+"/"VOL-" button has in "B/W BALANCE", "ADJUST" and
"SETUP" mode.

d). "POS+" and "POS-" are used for channel switch only. "LINE" works only

in "B/W BALANCE" mode.

e). Please refer to description in (4-4) for functions of other buttons.

6. Special functions

6-1. Magic function of "DISPLAY/" button

"DISPLAY" button can be used to cancel OSD display. This can be applied to

practical operation to simplify operation.

1). The fixed OSD display of "FACTORY", "BUS OPEN", "B/W BALANCE",
"ADJUST" and "MUTE" can not be cancelled by pressing "DISPLAY" button.

2). In "B/W BALANCE" mode, the OSD of adjusting options can not be cancelled
by pressing "DISPLAY". In other OSD status of "B/W BALANCE" mode,
press "DISPLAY" can return to the OSD of adjusting options.

3). In "ADJUST" mode, press "DISPLAY" button can not cancel the OSD of
adjusting options. In other OSD status of "ADJUST" mode, press "ADJUST"
button can return to the OSD of adjusting options.

4). In "SETUP" mode, press "DISPLAY" button can not cancel the OSD of
adjusting options. In other OSD status of "SETUP" mode, press "DISPLAY"
button can return to the OSD of adjusting options.

5). In other OSD display modes, press "DISPLAY" button can cancel the current
OSD and return to non-OSD mode.

6-2. Auto-search function

This function is available when "SEARCH CHECK" is set to "1". This

function can check automatically if program positions are stored in EEPROM. If

no program position is stored, it can automatically enter into auto-search mode
after start-up.

6-3. EEPROM check function

When EEPROM is damaged, TV set can not work normally, because the bus
adjusting data and the result of setting options are stored in EEPROM. Therefore
CPU will automatically check EEPROM upon cold start-up. If the bus connected
with EEPROM is found making errors or the EEPROM is making errorsinitial
data will be called after start-up and forced blue background will turn up, with
flashing OSD displaying "EEPROM ERROR PLEASE CHECK" in big letters. In
this case, no operation can be done except turning off to check. If EEPROM is
partially damaged errors may not be found out.

6-4. User's remote control unit enabling "FACTORY" button function

User's remote control unit has no "PROD (producer)" button. This may bring
troubles to maintenance after TV sets exit the factory. Therefore a function
equivalent to "PROD" function is specially designed in the software. Its operation
is as follows
First press "REVIEW" button then press and hold the "VOL-" button on the TV
set and meanwhile press the "REVIEW" button again. The function of "PROD"
button is enabled then. Repeat the above steps can operate again.

6-5. EEPROM initialization function

During cold start-up, CPU will check au tomatically if new EEPROM is used (e.g.,

EEPROM is replaced in maintenance). If a new EEPROM is found CPU will
automatically read in initial data and store the data in the new EEPROM to ensure
normal operation.

6-6. Setting of factory flag and power logo
The factory flag consists of two lines, with 12 characters for each, which can be
used to set different content, on/off, style and size of characters, color, vertical
position and horizontal position. If factory flag is set and at least one line is set to
"ON", POWER LOGO will turn up after start-up if "POWER ON LOGO" is set to
"1". If at least one line is set to "ON", then factory flag OSD will appear when no
signal is received.

1) Operation instruction:
Press PROD button to enter into "FACTORY" mode. Press and hold VOL-

button on remote control unit till the volume decreases to "0", and meanwhile
press POS- button on the remote control unit to open factory flag setting up
menu.

The setting up menu consists of two screens used to adjust line 1 and line 2

respectively. After the setting up menu is open, press POS+/POS- button to
select different options. If display item is selected, a yellow bar will point out
the adjustable characters. If other options are selected, the OSD display will
become red. Otherwise, the display is in green. If an option to be set is
selected, press VOL+/VOL- button to set up different values.

Adjusting of display contentuse POS+/POS- button to select the adjusting

options on line1 or line 2. A yellow bar will point out the adjustable characters.
Use VOL+/VOL- button to adjust the content of characters indicated by the
yellow bar. Press PP button to select other characters on the same line.

The OSD of setting menu will keep on displaying. After setting is finished, press

DISPLAY to quit.

The setting of factory logo is "Seeing is attaining", that is, the content, color, size

and position displayed in the content line are the same as in normal display
except that represents the normal factory flag display is blank after
quitting. The effect attainable after adjustment can be seen objectively in the
course adjustment.

The setting of the two lines of display content should not overlap (even if one

line is set to "OFF") to avoid abnormal phenomena.

2) OSD display

A

LOGO2 ON SIZE 2*2

LOGO1 ON SIZE 2*2 H.POS 20 COLOR RED
H.POS 20 COLOR RED V.POS 40
V.POS 30

A

Maintenance adjustment

1 Adjusting +B voltage

1.1 testing point---------two ends of C561

1.2 if +B voltage won't meet the requirement, adjust RP551 level switch to make it comply with the
requirement.

14’’ 110V (CAIHONG picture tube )
21’’ 110V (CAIHONG picture tube )
25’’ 125V/130V (CAIHONG/HUAFEI picture tube )
29’’ 125V (YONGXIN picture tube )

2Picture/AFT IF coil T101 adjustment

2.1 Input the 38MHZ/38.9MHZ/45.75MHZ point frequency signal (input level 80db+5dbfrom C110

terminal.

2.2 Connect the digital voltage meter to the cross-point of R113 and R114.

2.3 Adjust T101 till the reading on the voltage meter is 3.6V

+0.02V.

3RF—AGC adjustment

3.1 Receive Philips circular testing signal.

3.2 Adjust the signal input level to 60db

3.3 Connect the digital voltage meter to TP-A.

3.4 Press the PRODfactorybutton on the maintenance use remote controller to start adjusting mode.

3.5 Press CH+ button to select RF.AGC option. Use VOL+ to adjust the value of RF.AGC till the
reading on the voltage meter is 2.5V

3.6 Press PRODFactorybutton till exit.

+1db

+0.1V

5Vertical size adjustment

5.1 Receive Philips testing (PAL system) signal.

5.2 Press PRODfactorybutton to start adjusting mode.

5.3 Press CH± button to select V.SIZE optionuse VOL± to adjust the value of V.SIZE till the
vertical overscan is 8%.

5.4 AV receive Philips testing (NTSC system) signal.

5.5 Press CH± button to select NT.V.SIZE function. Use VOL± to adjust the value of NT.V.SIZE till
the vertical overscan is 8%

5.6 Press PRODfactorytill exit.

6Vertical center adjustment

6.1 Receive Philips circular testing signal (PAL system).

6.2 Press PROD(factory) button on the maintenance use remote controller to start adjusting mode.

6.3 Press CH± button to select V.POSI option. Use VOL± to adjust the value of V.POSI till the picture is

in the vertical center.

6.4 AV receives Philips circular test signal (NTSC system).

6.5 Press CH±button to select NT.V.SIZE option. Use VOL±to adjust the value of NT.V.SIZE till the

picture appears in the vertical center.

6.6 Press PROD (FACTORY) till exit.

7Vertical linearity adjustment

7.1 Receive Philips circular test signal(PAL system).

7.2 Press PROD (FACTORY) button on the maintenance use remote controller to start adjusting mode.

7.3 Press CH± button to select V.LINE option. Use VOL± button to adjust the value of V.LINE till the

vertical linearity reaches the best.

7.4 AV receives Philips circular test signal (NTSC system).

7.5 Press CH± button to select NT.LINE option. Use VOL± button to adjust the value of NT.LINE till the

vertical linearity reaches the best.

7.6 Press PROD (FACTORY) button till exit.

8Screen character display adjustment

8.1 Receive Philips circular test signal (PAL system).

8.2 Use PROD (FACTORY) button to enter into adjusting mode.

8.3 Press CH± button to select OSD.H.POSI option. Use VOL± button to adjust the value of OSD.H.POSI

till the characters appear in the horizontal center position.

8.4 Press CH±button on the maintenance use remote controller to select OSD.V.POSI o ption. Use VOL±

button to adjust the value of OSD.V.POSI to make the characters appear in the vertical center(i.e. make the
caption of characters appear in the center of the caption frame of the Philips circular test signal).

8.5 Press CH± button to select OSD.CONT option. Use VOL±to adjust the value of OSD.CONT till the

character display achieves proper brightness.

8.6 Press PROD (FACTORY) button till exit.

9White balance adjustment

9.1 Receive white field signal.

9.2 Press PROD (FACTORY) button to start brightness/darkness balance adjusting mode.

9.3 Press CH± button and VOL± button to adjust t he foll o wing pa ra mete rs to th ei r in it ial st atu s (see table

below

Black/white balance parameters comparison

name Chinese name range Initial status

S-BRI
R-BIA
G-BIA

B-BIA
R-DRI
G-DRI
B-DRI
C.B/W

9.4 Press MUTE button on the remote controller to see a horizontal bright line on the screen. Adjust the

screen grid voltage till only one color just show its brightness.

9.5 Press relevant number buttons to increase the amount of another two colors till the horizontal bright line

turn into white. Then the darkness balance reaches the best(note: in the status of horizontal bright line,
press "2"// "3" and "6" and "7" can decrease and increase respectively the amount of red/green/blue in the
bright line.

9.6Press MUTE button to exit horizontal bright line. Set C.B.\W to 2brightness balance adjusting signal.

Adjust S-BRT to a proper value (such as 99) to achieve proper brightness. Press CH±, VOL± button to
adjust R.DRI/G.DRI/B.DRI till the picture turn into white. Then the brightness balance reaches the best.

9.6 Press PROD (FACTORY) button till exit.











0--127 Start from20
0--255 Start from 20
0--255 Start from20

0--255 Start from 20
0--127 Start from 60
0--15 Start from 8
0--127 Start from 60

0

m

V

f

N

f

N

f

N

N

f

N

N

Troubleshooting list

|Yes

No raster

Check V513/V512
/V511/V501

Check N551/V554
/VD554/R569

Check VD551/V551

Check R491 and horizontal
output transformer

Check VD552

Check whether the line
of B6 12V is normal

Check whether the line of
B1 110V is normal

Check V431 wavefor
normal or not

Check filament voltage

Check B3 190
line

Check voltage o

101pin

Check whether
V432 is normal

Check whether
XS901is normal

Replace N101

Replace T471/439
L441/C441

No picture

Check the video signal o

101/46 pin

Check the video signal o

801/16 pin

Check C211

Check the video signal of

101/42pin

Check horizontal output
transformer/V431/V432/V902
V922

Check N101/T101/A101/N703

Check voltage cross

101/11/13pins

Check N701

Replace N801

Check the video signal o

Replace N101

101/17pin

f

N

f

N

Horizontal raster (no vertical scan)

Check waveform o

451/7pin

Check waveform o

451/7pin

Check voltage
of N451/6pin

Check N451/VD451
normal or not

No sound

Check C451/L451/
V551/V552/V553

Check waveform of N101/52pin

Check waveform of N101/52
pin

Check waveform of N101/1pin

Check N101

Check waveform of N801/21pin

Check C819/R831/R832

Check waveform of N801/17pin

Check N801

Check waveform of N601/N602/3

Check voltage of N601/9pin

Check C622/C632/B901/B902

Check N601/N602

No color

Check relevant settings open or not

Check voltage of N101/39pin/36pin's
element/31pin normal or not

Reset according to adjusting
instruction

Check C210/C207/C208
/R205R206

Для ТВ Erisson 2105.

Пользовательский ПДУ содержит в себе
возможность управления входом в сервисное
меню телевизора. Контактная площадка
находится под указанной на рисунке кнопкой,
но сама кнопка не имеет металлизированного
напыления.

Для ТВ Erisson 2107, 14GX37

Аналогично модели 2105, пульт модели
2107(14GX37) содержит в себе возможность
управления входом в сервисное меню телевизора.
Контактная площадка находится
рисунке кнопкой, но сама кнопка не имеет
металлизированного напыления.

под указанной на