Sanus Systems PFV59S User Manual

PLATINUM FURNITURE
MODEL PFV59s - Digital TV Stand
Assembly Instructions
Congratulations and thank you for purchasing your new Sanus
Platinum Furniture Product. If you have any questions regarding
this or any other Sanus product, please contact our customer
service department at (800)359-5520, or www.sanus.com. It is
not necessary to contact the retailer with any questions or
Please follow these assembly instructions. This will save you
time, make assembly easier and prevent possible damage to
your new Digital TV Stand. Assistance may be required for
some assembly procedures. Correct assembly is your
responsibility.
BUS5306
BUS5306
We recommend that the unit is assembled on a soft surface
such as carpet. Please record your serial number in the space
provided below and retain this manual for future reference.
Serial No
This unit was manufactured using ISO 9000 certified systems. For improvement purposes, design and specifications are subject to change without notice.
Angle bracket
Glass top
Thinside
Left side
Long rail Left front
Glass shelf
Base
Glide (gray / black)
PART DESCRIPTION:
Base Left side Right side Thin side Right front Left front Long rail Back Glass top Glass shelf Steel bracket
Angle bracket Cable duct Gray glide Black glide Hardware pack
QTY
1 1 1
2 1 1 1 1 1 1 1
2
4
3
3 1
Angle bracket
Back
Rightside Steelbracket
Thinside
Right front
PART NUMBER
M20205A1PO M20206A1ZS M20207A1ZS M20208A1ZS M20209A1ZS M20210A1ZS M20211A1ZS M20212A1PO M20213A1PO M20214A1PO P816190 P816191A P840200 P815034A P815034 MH1181A0
TOOLS REQUIRED:
CUSTOMER SERVICE INFORMATION
THE TOLL FREE NUMBER WITHIN 14 DAYS OF PURCHASE.
TOLL-FREE NUMBER - (800) 359-5520 (USA ONLY)
THE FOLLOWING INFORMATION MUST BE SUPPLIED IN FULL:
1. YOUR NAME, ADDRESS AND TELEPHONE NUMBER.
2. PRODUCT MODEL NAME/NUMBER AND COLOR.
3. DESCRIPTION, PART NUMBER AND QUANTITY OF REQUIREDPARTS.
4. PURCHASE DETAILS:
5. SERIAL NUMBER OF THE UNIT PURCHASED. (LOCATEDON REAR OF UNIT)
-STORE THE UNIT WAS PURCHASEDFROM.
-DATE OF PURCHASE.
Bump-on P840022 x 18
B
Front edge
Glide (gray/black)
x6
Back edge
Base (underside)
Fasten6 glides to the base as shown. Note that there are 3 gray and 3 black glides. Use gray glides at front of the base if the stand is going to be placed on a light colored floor. Use Black glides at the front if the stand is going to be placed on a dark colored floor.
Left front panel
Large wooden dowels x 4
Right front panel
x6
Screw 3 connector rods into holes in left and right front panels as indicated above. Press fit 2 large wooden dowels into large holes in left and right panels as shown.
Left side panel
Small wooden dowels
x12
Press fit small wooden dowels into left and right sides as shown above.
Right side panel
Right side panel
Left side panel
x12
Insert cams into large holes in left and right sides as shown. Make sure arrows on the cams point towards the corresponding cam holes along the edges of the panels.
x4
Screw 4 connector rods into holes indicated in back panel.
Back
Base
x4
x2
Screw 4 connector rods into holes in the base as indicated above.
Insert 2 cams into large holes in the base as shown above.
Left side panel
Right side panel
Cable duct
Press fit the sides to the back as shown above. Turn the cams clockwise to tighten. Press fit 4 cable ducts into large holes in the back as shown.
Assistance may be needed for this step.
Press fit the sides and back assembly onto the base as shown. Turn the cams clockwise to tighten.
C
x5
Fasten the back to the base as shown above.
x2
D
Long rail
x2
Assistance may be needed for this step.
Hold the long rail in between the sides as illustrated. Insert the black barrel nuts into the holes in the long rail. Ensure the holes in the sidesare aligned with the holesin the long rail. Fasten the sides to the long rail as shown.
Press fit the front panels to the sides and base as shown.
Turn the cams clockwise to tighten.
Adjusting screw x 4
Thin side
Slide thin sides do wn slots in front pan els and back, ensuring silver surfaces face out. Screw each adjusting screw into sides by half of it's visible threaded length, then once this is done, tighten all 4 Adjusting screws fully into sides.
Steel bracket
Fit the long steel bracket into the rebate in the long rail and in the grooves in the s ides as shown above. Ensure the bracket is equally distanced from the sides on both ends.
A
x5
Once the bracket is adjusted in the sides, fasten it to the long rail using the screws shown above.
It is important that you hold the long rail against the steel bracket as you tighten the screws.
Bump-on(self adhesive)
x18
Attach 18 bump-ons to top surface of the back, sides, front rails, and steel bracket where shown above.
Assistance may be needed for this step.
When placing the glass top on the unit, pay attention to the following tips:
* Ensure painted side is facing down. * Back edge of the glass top must be flush with the back panel. * Glass top's overhang at the left side must match that of the right side. * Lift the glass when repositioning it, do not drag it as it could damage your glass.
Back edge of the glass top is flush with back panel.
Front edge
Above is the top view of the cabinet, indicating where the glass top should rest on the c abinet.
A
x4
Fasten the angle brackets to the back as shown above. Note - the angle brackets are essential for the strength of the stand.
Assistance will be needed for this step.
x6
Insert 2 shelf pins into the bottom holes in the right side. Place a piece of polystyrene (from the pack) onto
the base as shown above (Alternatively you could use a soft rag). Tilt the glass to one side and rest it on top
of the polystyrene.Then carefully push the glass inside the cabinet and rest the right side on the shelf pins.
Then raise the left side of the glass up and insert the remaining of the shelf pins into the left side and back.
Lower the glass onto the shelf pins.
NOTE: We recommend that all contents stored in or on this item of furniture be removed before shifting it. The manufacturers will not be held liable for damage caused when furniture is shifted without first removing its contents. If furniture is shifted we recommend that it is lifted not dragged.
Loading...