Samsung WT11H2P, WT11H2, WT10H2, WT10C1P, WT10C1 User Manual

...

Download

Page 1

1 2

BEFORE USING THE WASHER

CAUTIONS

PRECAUTIONS WHEN OPERATING

DESCRIPTION OF PARTS

● Remove the cap-hose from the drain

hose.

● In case of pump drained washer,

remove the cap-hose from the drain hole.

● Be sure that the washer is grounded.

T o avoid electrical shock,use a metal pipe for the ground connection. But, don't ground the washer with gas pipes or telephone lines to avoid to dangers of explosion or lightning strike.

● Do not put your hands into the spin

dryer basket when it is spinning.

Y our fingers can be caught by spinning laundry and damaged.

● Ventilation

opening must not be obstructed

by carpeting when the washing machine is installed on a carpeted floor.

● If the supply

cord of this appliance is damaged,

it must only be replaced by a repair shop appointed by the manufacturer,because special purpose tools are required.

● To

avoid overfilling and damages this appliance

must be filled with the operator present using a moderate water supply pressure only.

● This appliance is to be connected to the water

mains using new hose-sets and that old hose-sets should not be reused.

● Never allow children to operate

or play with the washer.

Children playing with the washer may accidentally fall into the washing tub.

● Be sure to cover with the inner

cover on laundry before spinning.

This prevents laundry from being tossed out and damaged.

● Before washing,check all pockets.

If nails or pins remain in pockets,they may damage the washer or clothes.

● Close the water tap a little if the

water pressure is too high.

● To avoid water splashes,

close the wash tub lid.

● Never splash water on the control panel.

● Disconnect the power cord from the

power supply when not in use.

● Don't use excessively hot water.

(50˚C or more)

Plastic parts may be deformed or damaged. Also, clothing may be deformed or decolored.

INNER LID

DRAIN HOSE

(with pump)

When you open this lid while

the spin basket is spinning,

the spinning will be stopped

by breake system.

POWER CORD

EARTH WIRE

(Option)

WATER DRAIN HOSE

(WITHOUT PUMP)

SPIN DRYER BASKET

SPIN DRYER HA TCH

WASH TUB LID

Be sure to keep the lid

closed during washing

and spinning.

CONTROL LEG

Adjust the control leg

for even placement.

Otherwise,excessive vibration

and noise can occur

during spinning

OVER FLOW

FILTER

LINT FILTER

This is used for gathering

the dregs which are made

during washing.

WASH TUB

PULSATOR

The plug’s shape

may not correspond

with this drawing.

SPIN DRYER LID

Page 2

3 4

1 2 3 4 5

4.CYCLE SELECTOR

This is used to set the Washing/Rinsing or Draining.

5. SPIN DRY TIMER

This is used to set the spin time 1-5 minutes.

1.WASH TIMER

This is used to set the wash time, 1-15 minutes.

2.WASH CONTROL

You can wash laundry effectively by various methods.

3.SPIN DRY TIMER

This is used to set the spin time 1-5 minutes.

4.WATER INTAKE

Connect water inlet to a tap with a suitable.

5.

DRAIN SELCTOR

Be sure to press the selector knob to ‘WASH’ while washing.

CONTROL PANEL WASHING PROCEDURE

FRONT PANEL

REAR PANEL

1.WATER

SELECTOR

During washing, WATER SELECTOR KNOB should be selected to wash. During spin rinsing, WATER SELECTOR KNOB should be selected to spin.

2.WASH TIMER

This is used to set the wash time, 1-15 minutes.

3.WASH

SELECTOR

You can wash laundry effectively by various methods.

Before starting washing, ; Connect the water supply hose and open the water tap.

check the following - Lay the drain hose down toward a sinkhole.(In case no drain pump)

- Place the drain hose in sink or bath.(In case drain pump)

- Connect the power cord to the power supply outlet .

1. Set the CYCLE SELECTOR KNOB to ‘WASH.RINSE’.

(in case drain pump ‘WASH’)

5. Put the cloths into

the wash tub and set the same water pressure to fill the tub so as not to exceed ‘H3’level.

6. Set the WASH TIMER

1-15minutes.

7. After washing, set the

CYCLE SELECTOR KNOB to ‘DRAIN’ for drain.

2. Set the WATER SELECTOR

KNOB to WASH .

3. Select the

WASH SELECTOR KNOB for desired mode.

TO WASH

SW-903(P)

4. Fill water in the wash

tub to the‘L1’ lower

water level by carefully adjusting the tap water and add the detergent.

1. Select the WASH CONTROL KNOB for desired mode.

5. Set the WASH TIMER

1-15minutes.

6. After washing Press the

DRAIN SELECTOR KNOB to ‘DRAIN’ for drain .

2. Press the

DRAIN SELECTOR KNOB to ‘WASH’ .

3. Fill water in the wash tub

to the ‘L1’ lower water level by carefully adjusting the tap water and add the detergent.

4. Put the cloths into the

wash tub and set the same water pressure to fill the tub so as not to exceed ‘H3’level.

(A)Type

(B)Type

SWT90C1(P) / SWT90C2(P) SWT10H0(P) /SWT10H1(P) /SWT10H2(P)

Page 3

(A)Type

3. As soon as the WASH TIMER shuts off, turn off the water tap.

ADDITIONAL RINSE

(SHOWER RINSE FOR )

W ASHING PROCEDURE

5 6

SPIN DRY

Set the WATER SELECTORKNOB to SPIN and CYCLE SELECTOR KNOB to ‘DRAIN’.

1. Transfer the clothes into the spin basket and arrange the clothes evenly.

RINSING

OVER FLOW RINSE

3. As soon as the WASH TIMER shuts off, turn off the water tap.

1. Keep suppling water(adjust water pressure

to ensure that the amount of water supplied does not exceed that water drained.)

2. Set the WASH TIMER 6~8minutes.

4. Set the CYCLE SELECTOR KNOB

to ‘DRAIN’.

3. Close the spin dryer lid.

4. Set the SPIN DRY TIMER 1-5minutes.2. Be sure to attach the safety cover and

close the inner lid.

inner lid

safty cover

inner lid

safety cover

1. Keep suppling water(adjust water pressure

to ensure that the amount of water supplied does not exceed that water drained.)

2. Set the WASH TIMER 6~8minutes.

4. Press the DRAIN SELECTOR

KNOB to ‘DRAIN’.

After rinsing you canselect this course for more effective rinse (Don't select only this course for rinse.) Load the laundry

evenly into the spin basket.

Supply water for about 1minute. Adjust the water flow to prevent overflow from the wash tub.

After stopping water supply, cover the laundry with safety cover and close the inner lid.

Close the spin dryer lid.

Set the SPIN DRY TIMER 2~3 minutes.

1. Set the CYCLE SELECTOR KNOB to ‘WASH.RINSE’.

(In case drain pump ‘WASH’)

5. Repeat this cycle until drain water

is clean. (2~3 cycle)

2. Supply the proper amount of water as not

to overflow the top of the washing tub.

3. Set the WASH TIMER

2~3minutes.

4. Drain the water.

Set the CYCLE SELECTOR KNOB to ‘DRAIN’

1. Press the DRAIN SELECTOR KNOB to ‘WASH’.

5. Repeat this cycle until water becomes clean.(2-3cycle)

2. Supply the proper amount of water as not to overflow the topof the washing tub and put the laundry into the washing tub.

3. Set the WASH TIMER 2-3 minutes.

4. Drain the water. Press the DRAIN SELECTOR KNOB to ‘DRAIN’ .

(A)Type (B)Type

Page 4

WATER

LEVEL

Low(44l)

Middle(56l)

High(67l)

TROUBLE

The washer does not work.

Clothes will not move freely.

Incomplete spinning

TROUBLE

Incomplete draining

The spin dryer basket will not

run.

CHECK POINT

Check that the power cord is connected to a power outlet well. Power stoppage?

Is the laundry overloaded?

Are the laundry arranged evenly?

AMOUNT OF CLOTHES

INSTALLATION

Leave some space

Space at last 15cm between the washer and the wall.

Place the washer on a sturdy flat surface.

If the washer is placed on an uneven or weak surface, noise or vibration may be occured. (Allowable is 2˚)

Never install the washer near water.

Do not place the washer in steamy rooms or where the washer is directly exposed to rain. Moisture may destroy the electrical insulation and cause an electrical shock hazard.

Avoid direct sunlight or heating devices.

As plastic and electrical components are affected by direct heat, never place the washer near heaters, boilers,etc. Do not place under direct sunlight.

CHANGING THE POSITION OF THE DRAIN HOSE

Before attempting to change the position of the drain hose,

disconnect the plug from the outlet.

1. Route the drain hose inside the machine.

2.T ake out the drain hose from the opposite hole and

insert the drain hose into the hose holder.

LAUNDRY GUIDE

MAINTENANCE

TROUBLE SHOOTING

CLEANING THE MACHINE

7 8

ENVIRONMENT

SPIN DRY TIME

DETERGENT

1. OVERFLOW FILTER

Pull the upper side of the

overflow filter with your fingers into the holes in the direction of arrow as shown in the figure.

2. CLEANING THE FILTER

Pull the overflow filter out and take up the filter

by removing 3 screws as shown in figure. Wash the filter and washing tub.

WHEN YOU LOAD THE LAUNDRY INTO THE SPIN BASKET.

Press the laundry evenly and put the safety cover into the spin basket drum as shown in the figure.

TO PICK OUT THE CLOTHING WHICH HAS FALLEN BETWEEN THE BASKET AND TUB.

For safty, pull the power supply plug out of the socket.

3. CLEANING THE WASHER BODY

Wipe off strains on the cabinet and operation panel with soft cloth.

Do not use benzene,thinners,cleanser,or wax, nor scrub the washer with a brush. Painted surfaces or plastic parts will be damaged.

Water Level

Shirts(Synthetics) Under Shirts(Cotton) Working clothes(Cotton)

Low

22 Pieces 38 Pieces 16 Pieces

Middle

29 Pieces 48 Pieces 20 Pieces

High

35 Pieces 58 Pieces 25 Pieces

TIME

1min. 1~2min. 3~5min.

5min.

AMOUNT OF DETERGENT

44g 56g 67g

TYPE OF LAUNDRY

Thin(synthetic fiber)

wool

cotton

thick(cotton)

-The amount of detergent is average. Follow the instruction detergent printed on the package for amount of detergent.

-Choose the amount of detergent depending on the fabric type.

CHECK POINT

Is the filter clogged with lint?

● See “Cleaning the

machine” on page 7.

Is the spin dryer lid closed completely? Are laundry(socks,etc.)falling out of the spin dryer basket and clinging to the axle?

● See “To pick out...” on

page 8.

70~80cm

Place a rag under the washer filter not to wet the floor.

Rotate the filter counterclockwise and pull out the filter.

3. Remove dirts and rotate the filter clockwise until it locks in position.

Rag

Open

Filter

HOW TO CLEAN THE FIL TER (In case drain pump)

1.Disassemble two screws from the spin dryer hatch.

2.Pull up the spin dryer hatch to remove it.

3.Remove the clothing.

4.Close the spin dryer hatch.

Install the drain hose about 70~80cm above the ground for pump model.

Hose holder

Page 5

Owner’s Instructions

SW-903(P)/SWT90C1(P) / SWT90C2(P) SWT10H0(P) /SWT10H1(P) /SWT10H2(P)

Before operating the unit, please read this manual

throughly, and retain for future reference.

BEFORE USING THE WASHER 1 CAUTIONS 1 PRECAUTIONS WHEN OPERATING 1 DESCRIPTION OF PARTS 2 CONTROL PANEL 3 WASHING PROCEDURE 4

TO WASH 4 SPIN DRY 5 RINSING 5 OVER FLOW RINSE 6 ADDITIONAL RINSE 6

INSTALLATION 7

ENVIRONMENT 7 CHANGING THE POSITION OF THE DRAIN HOSE 7

HOW TO CLEAN THE FILTER 7

CLEANING THE MACHINE 7

LAUNDRY GUIDE 8 MAINTENANCE 8 TROUBLESHOOTING 8 SPECIFICATIONS

IF YOU NEED HELP.

Do not hesitate to call your local samsung service center. They will be willing to help you. Be sure to give them your name,address,telephone number and the purpose of the call.

SPECIFICATION

DIMENSIONS (mm)

WATER PRESSURE

WEIGHT

EXTRACTION EFFICIENCY STANDARD QUANTITY OF WATER

CAPACITY (Maximum dry mass textiles)

MOTOR INPUT MOTOR MAX INPUT RATING TIME

SWT90C1(P) / SWT90C2(P) SW-903(P)

W820mm x D524mm x H1000mm W820mm x D524mm x H920mm W820mm x D524mm x H993mm

Washing:7.0kg Spinning:6.5kg Washing:7.0kg Spinning:6.5kg Washing:8.0kg Spinning:6.5kg Washing:400W Spinning:200W Washing:580W Spinning:200W Washing:400W Spinning:200W

0.05~0.78 MPa

0.5 ~ 8.0 kg .f/ cm

36 kg 50 %

Low : 44l Middle : 56l High : 67l

600W 790W 600W

Washing : 1Hour Spinning : 15minutes

SWT10H0(P) /SWT10H1(P) /SWT10H2(P)

CODE NO : DC68-01293A