Samsung WT10S2P, WT11S2, WT12S2, WT90C1, SW-903 Owner's Instructions Manual

1 2

DESCRIPTION OF PARTS

▶ In case of pump drained washer,

remove the cap-hose from
the drain hole.

▶▶

Ventilation

opening must not be obstructed
by carpeting when the washing machine is
installed on a carpeted floor.

▶▶

If the supply

cord of this appliance is damaged,
it must only be replaced by a repair shop
appointed by the manufacturer,because
special purpose tools are required.

▶▶

To

avoid overfilling and damages this appliance
must be filled with the operator present using a
moderate water supply pressure only.

▶▶

Be sure to cover with the inner

cover on laundry before spinning.

This prevents laundry from
being tossed out and damaged.

▶▶

To avoid water splashes,

close the wash tub lid.

▶▶

Never splash water on the control panel.

▶▶

Disconnect the power cord from the

power supply when not in use.

INNER LID

DRAIN HOSE

(with pump)

When you open this lid while

the spin basket is spinning,

the spinning will be stopped

by breake system.

POWER CORD

EARTH WIRE

(Option)

WATER DRAIN HOSE

(WITHOUT PUMP)

SPIN DRYER BASKET

SPIN DRYER HATCH

WASH TUB LID

Be sure to keep the lid

closed during washing

and spinning.

CONTROL LEG

Adjust the control leg

for even placement.

Otherwise,excessive vibration

and noise can occur

during spinning

OVER FLOW

FILTER

LINT FILTER

This is used for gathering

the dregs which are made

during washing.

WASH TUB

PULSATOR

The plug’s shape

may not correspond

with this drawing.

SPIN DRYER LID

3 4

44..

CYCLE SELECTOR

This is used to set the Washing/Rinsing or Draining.

55..

SPIN DRY TIMER

This is used to set the spin time 1-5 minutes.

44..

WATER INTAKE

Connect water inlet to a tap with a suitable.

55..

DRAIN SELCTOR

Be sure to press the selector knob to ‘WASH’ while washing.

Before starting washing, ; Connect the water supply hose and open the water tap.

check the following - Lay the drain hose down toward a sinkhole.(In case no drain pump)

- Place the drain hose in sink or bath.(In case drain pump)

- Connect the power cord to the power supply outlet .

1. Set the CYCLE SELECTOR KNOB to

‘‘

WASH••RINSE

’’..

(in case drain pump “WASH”)

5. Put the cloths into
the wash tub and
set the same water
pressure to fill the
tub so as not to
exceed ‘H3’level.

6. Set the WASH TIMER
1-15minutes.

7. After washing, set the

CYCLE SELECTOR KNOB
to ‘DRAIN’’for drain.

2. Set the WATER SELECTOR
KNOB to WASH .

3. Select the
WASH SELECTOR KNOB
for desired mode.

TO WASH

4. Fill water in the wash
tub to the‘‘L1’’lower

water level by carefully

adjusting the tap water
and add the detergent.

1. Select the WASH CONTROL KNOB
for desired mode.

5. Set the WASH TIMER

1-15minutes.

6. After washing Press the

DRAIN SELECTOR KNOB to
‘DRAIN’ for drain .

2. Press the

DRAIN SELECTOR KNOB
to ‘WASH’ .

3. Fill water in the wash tub

to the‘‘L1’’lower water
level by carefully
adjusting the tap water
and add the detergent.

4. Put the cloths into the

wash tub and set the
same water pressure
to fill the tub so as not to
exceed ‘H3’level.

(A)Type

(A)Type

(B)Type