Samsung WSP200 User Manual
Wireless
WSP200
MHz
900
Radio Frequency
Speakers
with 900 MHz Transmitter
Freedom From Wires
listen
anywhere
in your home
2
Congratulations on the purchase of your new WSP200 Wireless Stereo Speaker
System. This System uses the latest 900 MHz High Frequency Radio Signal that
can easily travel through walls, floors, ceilings or partitions to allow the finest
stereo sound reproduction.
You can use your Speakers almost anywhere in and around your home or, for
outdoor activities, just place them in the location of your choice. There is no
need to worry about cable connection between the transmitter and Speakers.
It is totally wireless!
Simply adjust the Volume and Tone Controls of the Speakers to your favorite
levels, sit back and enjoy music/sound programs from your Compact Disc, TV,
Hi-Fi Systems or Portable CD Player or Cassette/Radio.
INTRODUCTION
With any sound system, the quality of the music is only as good as the source.
In today’s recording industry, there is a great variation in both the quality and
clarity of music soundtracks.
Although CDs are digital in format, many are still reproductions of original analog recordings. As a result, some recordings (even some CDs) have a fairly high
noise level that when amplified produces undesirable background static or hiss.
This type of static tends to be more noticeable in some easy-listening or classical
music recordings, particularly those pieces that have relatively quiet passages
and/or prolonged orchestral pauses.
In order to combat this problem, the WSP200 incorporates a state of the art
filtering system that eliminates inherent background static without, in any way,
compromising the dynamic range of the Speakers.
The result of this technological breakthrough means that you, the listener, can
enjoy dynamic static-free music in an unlimited number of indoor and outdoor
settings… without the need for wires to transmit the audio signal.
A NOTE TO THE AUDIOPHILE
3
CONTROL LOCATIONS
TRANSMITTER
1) LED Indicator (Power ON)
2) Power OFF Switch and Channel Selector
3) AUDIO IN Jack (L) - Connect to Music Source
4) AUDIO IN Jack (R) - Connect to Music Source
5) DC Input Jack
1
2
5
4
3
SPEAKER
6) Frequency Channel Selector
7) Tone Control Knob
8) Power OFF and Volume Control Knob
9) DC Input Jack
10) MODE Switch (To Select Left/Mono or Right Channel)
11) Battery Compartment
REMOVE BATTERIES IF NOT IN USE
FOR A PERIOD OF TIME.
WIRELESS SPEAKER SYSTEM
IMPEDANCE
MAXIMUM OUTPUT POWER
POWER SOURCE
AC : 120V 60Hz
DC : BATTERIES "D"(1.5V) x 8
MADE IN CHINA
DC IN
WS-91
6
7
8
9
10
11
4
INSTALLING THE TRANSMITTER
1) CONNECTING POWER
(A) DC OPERATION
Your Transmitter is supplied with a Battery
Tray. Insert four (4) x AA Alkaline batteries
(not supplied) to the battery slot as indicated. Attach the battery tray to the bottom
of the Transmitter unit. Be sure to insert
the three plastic locks of the battery tray
into the openings of the transmitter base,
then slide to the front for firm attachment.
(B) AC OPERATION
Your system is supplied with one 600 mA
AC Adapter. Insert the plug of the AC
adapter in to the DC Jack at the rear of the
Transmitter, then plug the other end of the
AC Adapter in to a conveniently located
electrical wall outlet.
You are recommended to use the AC
Adapter as often as possible, as this is
still the most economical power source!
2) CONNECTING TO YOUR AUDIO SOURCE
• Connect one end of the supplied patch
cord to the Transmitter's Left
(WHITE) and
Right (RED) AUDIO IN Jacks
.
• Then connect the other end of the patch
cord to the Audio Sources Left (WHITE)
and Right (RED) AUDIO OUT Jacks.
You need to properly set up the Transmitter to send a wireless signal to the
Speakers. There are two things you must do. First, provide power to the
Transmitter, and second, connect the Transmitter to the Audio Source.
1 2 3
CHANNEL
OFF
SIZE "AA" x 4 PCS.
L - AUDIO IN - R
DC 6V
L
R
AUX. OUT
AUDIO SOURCE
(eg.: TV, VCR, HOME STEREO)
AUDIO IN
R
L
R
L
L - AUDIO IN - R
DC 6V
Battery Tray
Loading...