Samsung WS32Z30HP, WS32Z40HT, CW29Z308T, S63B Schematic
1. Make sure all protective devices are properly installed
including non-metallic handles and compartment covers
when installing or re-installing the chassis or chassis
assemblies.
2. Make sure that no gaps exist between the cabinets for
children to insert their fingers in to prevent children from
receiving electric shocks. Gaps mentioned above include
ventilation holes of a too great magnitude between the
vaccum tube and the cabinet mask, and the improper
installation of the rear cabinet.
Errors may occur when the resistance is below 1.0 ㏁ or
over 5.2 ㏁.
In these cases, make sure that the device is repaired
before sending it back to the customer.
3. Check for Electricity Leakage (Figure 1-1)
Warning: Do not use an insulated transistor for checking
the leakage. Use only those current leakage testers or
mirroring systems that comply with ANSIC 101.1 and the
Underwriter Laboratory's specifications (UL1410, 59.7).
Fig. 1-1 AC Leakage Test
4. A high voltage is maintained within the specified limits
using safety parts, calibration and tolerances. When
voltage exceeds the specified limits, check each special
part.
5. Warning for Engineering Changes:
Never make any changes or additions to the circuit
design or the internal part for this product.
Ex: Do not add any audio or video accessory
connectors. This might cause physical damage.
Furthermore, any changes or additions to the original
design/engineering will invalidate the warranty.
6. Warning - Hot Chassis:
Some TV chassis are directly connected to one end of
the AC power cord for electrical reasons.
Without insulated transistors, the product can only be
repaired safely when the chassis is connected to the
earthed end of the AC power source.
To make sure the AC power cord is properly connected,
follow the instructions below. Use the voltmeter to
measure the voltage between the chassis and the
earthed ground. If the measurement is over 1.0V, unplug
the AC power cord and change the polarity before reinserting it. Measure the voltage between the chassis
and the ground again.
7. Some TV chassis are shipped with an additional
secondary grounding system. The secondary system is
adjacent to the AC power line. These two grounding
systems are separated in the circuit using an
unbreakable/unchangeable insulation material.
8. When any parts, material or wiring appear overheated or
damaged, replace them with new regular ones
immediately. When any damage or overheating is
detected, correct this immediately and make a regular
check of possible errors.
9. Check for the original shape of the lead, especially that
of the antenna wiring, any sharp edges, the AC power
and the high voltage power. Carefully check if the wiring
is too tight, incorrectly placed or loose. Never change the
space between the part and the printed circuit board.
Check the AC power cord for possible damages. Keep
the part or the lead away from any heat-emitting
materials.
Precaution
Samsung Electronics 1-1
To avoid possible damages or electric shocks or exposure to radiation, follow the instructions below with regard to safety,
installation, service and ESD..
1. Precaution
1-1 Safety Precautions
(READING SHOULD
DEVICE
UNDER
TEST
EXPOSED METAL
2-WIRE CORD
ALSO TEST WITH
PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)
TEST ALL
SURFACES
LEAKAGE
CURRENT
TESTER
NOT BE ABOVE
0.5mA)
EARTH
GROUND
10. Safety Indication:
Some electrical circuits or device related materials
require special attention to their safety features, which
cannot be viewed by the naked eye. If an original part is
replaced with another irregular one, the safety or
protective features will be lost even if the new one has a
higher voltage or more watts.
Critical safety parts should be bracketed with ( ).
Use only regular parts for replacements (in particular,
flame resistance and dielectric strength specifications).
Irregular parts or materials may cause electric shock or
fire.
Precaution
1-2 Samsung Electronics
!
1. The service instructions are printed on the cabinet, and
should be followed by any service personnel.
2. Make sure to unplug the AC power cord from the power
source before starting any repairs.
(a) Remove or re-install parts or assemblies.
(b) Disconnect the electric plug or connector, if any.
(c) Connect the test part in parallel with the electrolytic
capacitor.
3. Some parts are placed at a higher position than the
printed board. Insulated tubes or tapes are used for this
purpose. The internal wiring is clamped using buckles to
avoid contact with heat emitting parts. These parts are
installed back to their original position.
4. After the repair, make sure to check if the screws, parts
or cables are properly installed. Make sure no damage is
caused to the repaired part and its surroundings.
5. Check for insulation between the blade of the AC plug
and that of any conductive materials (i.e. the metal
panel, input terminal, earphone jack, etc).
6. Insulation Check Process: Unplug the power cord from
the AC source and turn the switch on. Connect the insulating resistance meter (500v) to the AC plug blade.
The insulating resistance between the blade of the AC
plug and that of the conductive material should be more
than 1 ㏁.
7. Any B+ interlock should not be damaged.
If the metal heat sink is not properly installed, no
connection to the AC power should be made.
8. Make sure the grounding lead of the tester is connected
to the chassis ground before connecting to the positive
lead. The ground lead of the tester should be removed
last.
9. Beware of risks of any current leakage coming into
contact with the high-capacity capacitor.
10. The sharp edges of the metal material may cause
physical damage, so ensure wearing protective gloves
during the repair.
Precaution
Samsung Electronics 1-3
Warning 1: First carefully read the "Safety Instruction" in this service manual.
When there is a conflict between the service and the safety instructions, follow the safety instruction at all times.
Warning 2: Any electrolytic capacitor with the wrong polarity will explode.
1-2 Servicing Precautions
1-3 Static Electricity Precautions
1. Some semi-conductive ("solid state") devices are
vulnerable to static electricity. These devices are known
as ESD. ESD includes the integrated circuit and the field
effect transistor. To avoid any materials damage from
electrostatic shock, follow the instructions described
below.
2. Remove any static electricity from your body by
connecting the earth ground before handling any
semi-conductive parts or ass'ys. Alternatively, wear a
dischargeable wrist-belt.
(Make sure to remove any static electricity before
connecting the power source - this is a safety instruction
for avoiding electric shock)
3. Remove the ESD ass'y and place it on a conductive
surface such as aluminum foil to prevent accumulating
static electricity.
4. Do not use any Freon-based chemicals.
Such chemicals will generate static electricity that
causes damage to the ESD.
5. Use only grounded-tip irons for soldering purposes.
6. Use only anti-static solder removal devices.
Most solder removal devices do not support an
anti-static feature. A solder removal device without an
anti-static feature can store enough static electricity to
cause damage to the ESD.
7. Do not remove the ESD from the protective box until the
replacement is ready. Most ESD replacements are
covered with lead, which will cause a short to the entire
unit due to the conductive foam, aluminum foil or other
conductive materials.
8. Remove the protective material from the ESD
replacement lead immediately after connecting it to the
chassis or circuit ass'y.
9. Take extreme caution in handling any uncovered ESD
replacements. Actions such as brushing clothes or lifting
your leg from the carpet floor can generate enough static
electricity to damage the ESD.
Precaution
1-4 Samsung Electronics
CAUTION
These servicing instructions are for use by
qualified service personnel only.
To reduce the risk of electric shock do not
perform any servicing other than that contained in the
operating instructions unless you are qualified to do so.
Precaution
Samsung Electronics 1-5
1-4 Installation Precautions
1. For safety reasons, more than two people are required
for carrying the product..
2. Keep the power cord away from any heat emitting
devices, as a melted covering may cause fire or electric
shock.
3. Do not place the projector in areas with poor ventilation
such as a bookshelf or closet. The increased internal
temperature may cause fire.
4. Bend the external antenna cable when connecting it to
the product. This is a measure to protect it from being
exposed to moisture. Otherwise, it may cause a fire or
electric shock.
5. Make sure to turn the power off and unplug the power
cord from the outlet before removing the product. Also
check the antenna cable or the external connectors if
they are fully unplugged. Damage to the cord may cause
fire or electric shock.
6. Keep the antenna far away from any high-voltage cables
and install it firmly. Contacting the high-voltage cable or
the antenna falling over may cause fire or electric shock.
7. When connecting the RF antenna, check for a DTV
receiving system and install a separate DTV reception
antenna for areas with no DTV signal.
8. Check the basics of the screen test.
- Image position/size, Tilt adjustment
1-6 Samsung Electronics
MEMO
Product Specification
Samsung Electronics 2-1
2. Product Specification
2-1 Product Features
Block Specfication EU East asia/CIS Remark
CRT
- Slimmer than existing CRTs
Existing: 495mm → Slimfit : 365mm
Vixlim CRT Vixlim CRT
RF Part - Same as for the OZ(S62A) Model TMQZ2-402A, PAL-CW TMQZ2-401A, PAL-CS
Power
- Input Voltage : AC 160~300V
- Stand-By : Less than 3W
STR-X6750 STR-X6750
Video
- PAL/SECAM/NT4.43/NT3.58
- Progressive 100Hz(Full 100Hz)
VCT69xyP
CXA2165
VCT69xyP
CXA2165
Audio
- Output : 10W x 2
- Function : SRS-TRUSURROUND
VCT69xyP VCT69xyP
Cabinet
- New Front and Back Cabinets
- 184mm of saved space compared to
the existing model
A11:580mm → Z40:396mm
Z30 Design Applied
FPTV Looking Design
Black Bezel 2Tone
Color Design
Z30(OZ) Design Applied
FPTV Looking Design
Black Bezel 2Tone
Color Design
■ Core Parts Functions
- VCT69xyP : RF-CVBS,EXT-CVBS,FRONT Y,C,SCART1 R/G/B input and Video Signal Processing.
Provides S-IF Analog audio And Digital audio signal input and decoding functions.
I2C-Comunication,Master Control Micom, Rom Micom
- CXA2165 : H-out,VD-P,VD-N,RGB output,Video and Deflection Signal Processing.
- MST3383M : HDMI decoding Functions
- TW9906 : PIP Processor
Product Specification
2-2 Samsung Electronics
2-2 Key Features
Model
WS32Z40 / CW29Z40
(Europe)
WS32Z40 / CW29Z40 / CS29Z40
WS32Z30 / CW29Z30 (CIS)
Voltage AC230V 160~300V
Frequency of Operation 50/60 Hz 50/60 Hz
Dimensions(mm)
934X399X568 (32")
796X421X593 (29")
934X399X568 (32")
796X421X593 (29")
Weight
54.5Kg (32")
43.0Kg (29")
54.5Kg (32")
43.0Kg (29")
■ H/W Configuration
- Slimfit(Low Depth) CRT adopted
- Progressive 100Hz (Full 100Hz)
■ S/W Configuration
- Multi System PAL/SECAM(CIS Option:NTSC4.43/NTSC3.58)
- ATS, Auto Wide, Pre Channel, On/Off Timer, Zoom, Blue Screen
■ Picture
- System
Video : PAL/SECAM/ NTSC3.58(CIS Option)
Sound : B/G, D/K, I, L/L', M(CIS Option)
- Black Level expansion, CTI, VM, Dynamic focus
- AKB(Auto kinetic Bias)
- Still picture, Digital Noise reduction
- PIP (2Tuner) : Option
- Auto Wide
■ Sound
- System : A2+Niacam Stereo, SRS Trusurround
- Output : 10W+10W
- Speaker : 2EA
- AVL, Melody, Auto Stereo, Auto Mute, Equalize
■ In/Out Terminals
- Side : 1 CVBS Input, 1 S-Video Input, Sound L/R
- Rear : 2 Scart, 1 Component(480i/480P/576i/576P/720P/1080i/1080P 50Hz/60Hz), 1 HDMI Input(Option)
■ Remocon : TM86
■ Power Supply
- Europe(230V), CIS(160V- 300V)
■ Power Consumption
- Stand-by : 3W
- Max Power : 180W
Product Specification
Samsung Electronics 2-3
2-3 Specifications Analysis
Model WS32Z30/CW29Z30 CW-29Z338T
Chassis S62B S63B
Design
Basic
Product Type Slimfit CRT Slimfit CRT
Digital Display - -
Screen Size 32 / 29 inch 29 inch
Aspect Ratio 16:9 / 4:3 4:3
Visual Quality
Digital Comb Filter -
O
Screen Pitch 0.73 0.73
AKB
O O
Digital Noise Reduction
O O
DNIe - -
3:2 Pull Down Support - -
Audio
Base/Treble/Balance - -
Equalizer 5 Band 5 Band
AVL
O O
Surround SRS-WOW SRS-TRUSURROUND
Speaker System Direct Direct
Speaker Output 10W + 10W 10W + 10W
Function
Dual Screen Function - -
Double Screen - -
TTX 10page/200page(Option) 750page(Option)
Still Picture
O O
Auto Jack Recognition - -
Ports
Antenna In Rear : 1 Rear : 1
External In Rear:2, Side:1 Rear:2, Side:1
S-Video Side : 1 Side : 1
Y/Pb/Pr - Rear : 1
PC - -
DVI - -
HDMI - -
Digital Audio Out - -
Video Out Rear : 1 Rear : 1
Audio Out - -
2-4 Accessories
Accessories Item Item code Remark
Supplied Accessories
Remote Control
Batteries
AA59-00382A
4301-000121
Samsung Service centerOwner's Instructions AA68-03784A
Warranty Card
Registration Card
Safety Guide Manual
BN68-00514D
AA68-03575D
AA68-03242E
Accessories that can be
purchased additionally
Video Cable
Audio Cable
-
Internet shopping mall
Component Cable(RCA) -
Antenna Cable -
HDMI Cable -
HDMI/DVI Cable -
Product Specification
2-4 Samsung Electronics
Alignment & Adjustment
3. Alignment & Adjustment
3-1 Service Instruction
1. General Adjustment :
In general, a color TV can provide ideal visual quality by adjusting the basic settings such as the vertical size, horizontal size,
focus, etc.
Display a black and white picture on the screen to check if the picture is clearly displayed.
If there are some 'spotted' points on the screen when displaying a black and white picture, degauss the screen using the
degauss coil. If the spotted points remain, re-adjust the purity and the convergence. This completes the basic performance
examination.
Notice.
■ These adjustments and the check list are only applied to S63A chassis-applied models.
■ Only use 230V for the measurement set. It is recommended using an insulation transformer when supplying power to
the set so as to prevent shock to the set or to yourself.
■ These adjustment specifications have been created on the basis of the domestic S63A chassis-applied remote control
model. Some of the contents may be changed subject to the sales location and the product specifications.
2. When replacing the F_Box Board :
Since the software is loaded to the EPROM of the F_box board, check the version of the
software of the EPROM.
To check the version of the software, Enter service mode presee the key on the reomte
control according to the following seguenu.
(in stand-by status) Info→Menu→Mute→Power→ON
The software information will then be displayed below the OSD menu.
The notation of the software information : For example, T_SHPEU_1009 refers to
"CORSET BASIC MODEL Europe. ver.1009".
Since the settings including the Channel
information, Deflection, etc. are saved to the
nvRAM, reconfigure these settings when
replacing the System Board
3. When replacing the Main Board : No adjustments required. Except that Tilt adjustment, focus adjustment, screen voltage
setting and W/B adjustment are all required.
4. When replacing the CRT Ass'y : No adjustments required.
5. When replacing the front panel master power switch : No adjustments required.
6. When replacing the Side AV : No adjustments required.
7. When replacing the control switch : No adjustments required.
Samsung Electronics 3-1
Alignment & Adjustment
3-2 How to Access Service Mode
1. To enter Service Mode, press the keys on the remote control according to the following sequence. (in Stand-by status)
Info → Menu → Mute → Power On
※ When failing to enter Service Mode, repeat the procedure above.
2. The initial screen of Service Mode.
< Europe>
1. Deflection
2. 480p/576p
3. 720p/1080i
4. 4:3 offset--Vixlm
5. Video Adkust1
6. Video Adkust2
7. Video Adkust3
8. Video Adkust4
9. Video Adkust5
10. Video Adkust6
11. Video Adkust7
12. Video Adkust8
13. OPTION (55 OB 00)
14. YC Delay
15. EEPROM
16. Bus Stop
17. checksum 0000
18. RESET
3. Functions of the Keys within Service Mode
MENU Show all menus
▲ / ▼
◀ / ▶
3-2 Samsung Electronics
Move the cursor to select an item.
Adjust the selected configuration value
Alignment & Adjustment
3-3 Factory Data
■ Europe
1. DEFLECTION(PAL)
No item Range intial
0 V Amp 0~63 30 30 34 Adjust
1 V Shift 0~63 26 26 27 Adjust
2 H EW 0~63 30 30 21 Adjust
3 H Shift 0~63 36 36 42 Adjust
4 V Linearity 0~15 6 6 6 FIX
5 Upper Linearity 0~15 0 0 0 FIX
6 Lower Linearity 0~15 1 1 1 FIX
7 V SC 0~15 3 3 4 FIX
8 H Parabola 0~63 32 32 48 Adjust
9 Upper Corner 0~63 37 37 38 Adjust
10 Lower Corner 0~63 34 34 35 Adjust
11 H Trapezium 0~63 40 40 37 Adjust
12 Bow 0~63 32 32 34 Adjust
13 Angle 0~63 30 30 28 Adjust
14 V Position 0~63 32 32 32 FIX
15 H Parablar_Pal(Offset) 0~63 0 0 0 FIX
16 Upper Corner_Pal(Offset) 0~63 0 0 0 FIX
17 Lower Corner_Pal(Offset) 0~63 0 0 0 FIX
18 Bow(Offset) 0~63 0 0 0 FIX
WS32Z30/40 (32") CW29Z30/40 (29")
Data Data
Remark
2. DEFLECTION(NTSC)
No item Range intial
0 V Amp 0~63 -4
1 V Shift 0~63 -3 -3 -3 Adjust
2 H EW 0~63 0
3 H Shift 0~63 -3
4 V Linearity 0~15 0 0 0 Adjust
5 Upper Linearity 0~15 0 0 0 FIX
6 Lower Linearity 0~15 0 0 0 FIX
7 V SC 0~15 0 0 0 FIX
8 H Parabola 0~63 0 0 0 Adjust
9 Upper Corner 0~63 0 0 0 Adjust
10 Lower Corner 0~63 0 0 0 Adjust
11 H Trapezium 0~63 4 4 4 Adjust
12 Bow 0~63 0 0 0 Adjust
13 Angle 0~63 0 0 0 Adjust
14 V Position 0~63 0 0 0 FIX
15 H Parablar_Pal(Offset) 0~63 0 0 0 FIX
16 Upper Corner_Pal(Offset) 0~63 0 0 0 FIX
17 Lower Corner_Pal(Offset) 0~63 0 0 0 FIX
18 Bow(Offset) 0~63 0 0 0 FIX
WS32Z30/40 (32") CW29Z30/40 (29")
Data Data
-6 → -4
-2 → 0
0 → -3
-6 Adjust
-2 Adjust
0 Adjust
Remark
Samsung Electronics 3-3
Alignment & Adjustment
3-4 Samsung Electronics
Alignment & Adjustment
3. DTV DEFLECTION OFFSET(480P)
No item Range intial
0 V Amp -63~63 2 2 0 Adjust
1 V Shift -63~63 0 0 0 Adjust
2 H EW -63~63 0 0 0 Adjust
3 H Shift -63~63 0 0 0 Adjust
4 V Linearity -15~15 0 0 0 Adjust
5 Upper Linearity -15~15 0 0 0 FIX
6 Lower Linearity -15~15 0 0 0 FIX
7 V SC -15~15 0 0 0 FIX
8 H Parabola -63~63 0 0 0 Adjust
9 Upper Corner -63~63 0 0 0 Adjust
10 Lower Corner -63~63 0 0 0 Adjust
11 H Trapezium -63~63 0 0 0 Adjust
12 Bow -63~63 0 0 0 Adjust
13 Angle -63~63 0 0 0 Adjust
14 V Position -63~63 0 0 0 FIX
15 UP-UCG (Up Corner Semi Control) -3~3 0 0 0 FIX
16 LO-UCG (Low Corner Semi Control) -3~3 0 0 0 FIX
17 UP-UCP (Up Corner posiotion Control) -3~3 0 0 0 FIX
18 LO-UCP (Low Corner posiotion Control) -3~3 0 0 0 FIX
WS32Z30/40 (32") CW29Z30/40 (29")
Data Data
Remark
4. DTV DEFLECTION OFFSET(576P)
No item Range intial
0 V Amp -63~63 6 6 6 Adjust
1 V Shift -63~63 -4 -4 -4 Adjust
2 H EW -63~63 0 0 0 Adjust
3 H Shift -63~63 0 0 0 Adjust
4 V Linearity -15~15 0 0 0 Adjust
5 Upper Linearity -15~15 0 0 0 FIX
6 Lower Linearity -15~15 0 0 0 FIX
7 V SC -15~15 0 0 0 FIX
8 H Parabola -63~63 0 0 0 Adjust
9 Upper Corner -63~63 0 0 0 Adjust
10 Lower Corner -63~63 0 0 0 Adjust
11 H Trapezium -63~63 3 3 8 Adjust
12 Bow -63~63 0 0 0 Adjust
13 Angle -63~63 0 0 0 Adjust
14 V Position -63~63 0 0 0 FIX
15 UP-UCG (Up Corner Semi Control) -3~3 0 0 0 FIX
16 LO-UCG (Low Corner Semi Control) -3~3 0 0 0 FIX
17 UP-UCP (Up Corner posiotion Control) -3~3 0 0 0 FIX
18 LO-UCP (Low Corner posiotion Control) -3~3 0 0 0 FIX
WS32Z30/40 (32") CW29Z30/40 (29")
Data Data
Remark
Samsung Electronics 3-5
Alignment & Adjustment
5. DEFLECTION OFFSET(720P)
No item Range intial
0 V Amp 0~63 0 0 0 Adjust
1 V Shift 0~63 0 0 0 Adjust
2 H EW 0~63 0 0 0 Adjust
3 H Shift 0~63 0 0 0 Adjust
4 V Linearity 0~15 0 0 0 Adjust
5 Upper Linearity 0~15 0 0 0 FIX
6 Lower Linearity 0~15 0 0 0 FIX
7 V SC 0~15 0 0 0 FIX
8 H Parabola 0~63 0 0 0 Adjust
9 Upper Corner 0~63 0 0 0 Adjust
10 Lower Corner 0~63 0 0 0 Adjust
11 H Trapezium 0~63 0 0 0 Adjust
12 Bow 0~63 0 0 0 Adjust
13 Angle 0~63 0 0 0 Adjust
14 V Position 0~63 0 0 0 FIX
15 UP-UCG (Up Corner Semi Control) 0~3 0 0 0 FIX
16 LO-UCG (Low Corner Semi Control) 0~3 0 0 0 FIX
17 UP-UCP (Up Corner posiotion Control) 0~3 0 0 0 FIX
18 LO-UCP (Low Corner posiotion Control) 0~3 0 0 0 FIX
WS32Z30/40 (32") CW29Z30/40 (29")
Data Data
Remark
6. DEFLECTION OFFSET(1080I)
No item Range intial
0 V Amp 0~63 -15 -15 -15 Adjust
1 V Shift 0~63 -5 -5 -5 Adjust
2 H EW 0~63 4 4 4 Adjust
3 H Shift 0~63 -3 -3 -3 Adjust
4 V Linearity 0~15 0 0 0 Adjust
5 Upper Linearity 0~15 0 0 0 FIX
6 Lower Linearity 0~15 0 0 0 FIX
7 V SC 0~15 0 0 0 FIX
8 H Parabola 0~63 0 0 0 Adjust
9 Upper Corner 0~63 0 0 0 Adjust
10 Lower Corner 0~63 0 0 0 Adjust
11 H Trapezium 0~63 5 5 5 Adjust
12 Bow 0~63 0 0 0 Adjust
13 Angle 0~63 0 0 0 Adjust
14 V Position 0~63 0 0 0 FIX
15 UP-UCG (Up Corner Semi Control) 0~3 0 0 0 FIX
16 LO-UCG (Low Corner Semi Control) 0~3 0 0 0 FIX
17 UP-UCP (Up Corner posiotion Control) 0~3 0 0 0 FIX
18 LO-UCP (Low Corner posiotion Control) 0~3 0 0 0 FIX
WS32Z30/40 (32") CW29Z30/40 (29")
Data Data
Remark
3-6 Samsung Electronics
Alignment & Adjustment
7. 4:3 OFFSET_VIXLIM
No item Range intial
1 H Parabola -20~20 0 0 0 Adjust
2 Upper Corner -20~20 0 0 0 Adjust
3 Lower Corner -20~20 0 0 0 Adjust
4 Bow -20~20 0 0 0 Adjust
5 Angle -20~20 0 0 0 Adjust
6 H Shift -20~20 0 0 0 Adjust
7 H Parabola NT -20~20 0 0 0 Adjust
8 Upper Corner NT -20~20 0 0 0 Adjust
9 Lower Corner NT -20~20 0 0 0 Adjust
10 Bow NT -20~20 0 0 0 Adjust
11 Angle NT -20~20 0 0 0 Adjust
12 H Shift -20~20 0 0 0 Adjust
WS32Z30/40 (32") CW29Z30/40 (29")
Data Data
Remark
8. VIDEO ADJUST 1
No item Range intial
0 R CutOff 0~63 20 20 20 Adjust
1 G CutOff 0~63 20 20 20 FIX
2 B CutOff 0~63 20 20 20 Adjust
3 R Drive 0~63 32 32 32 Adjust
4 G Drive 0~63 32 32 32 FIX
5 B Drive 0~63 32 32 32 Adjust
6 Sub Bright 0~63 15 15 15 Adjust
7 Sub Contrast 0~15 9 9 9 Adjust
8 Bright VCTP 0~256 140 140 140 FIX
9 Contrast VCTP 0 ~ 63 28
10 SAT-VCTP 0 ~ 63 23
11 Tint VCTP 0 ~ 23 10 10 10 FIX
12 SC_RGB_ BRTADJ -128 ~ 127 128 128 128 FIX
13 SC_RGB_ CONADJ 0 ~ 63 45 45 45 FIX
14 SC_RGB_ USATADJ 0 ~ 63 42
15 SC_RGB_ VSATADJ 0 ~ 63 42
16 RGB24_BRTADJ 0~255 14
17 RGB24_CONADJ 0 ~ 63 30 30 30 FIX
18 RGB24_ USATADJ 0 ~ 63 30
19 RGB24_ VSATADJ 0 ~ 63 30
20 RGB24_BR_HD 0~255 0
21 RGB24_CO_HD 0 ~ 63 30 30 30 FIX
22 RGB24_ USA_HD 0 ~ 63 30
23 RGB24_ VSA_HD 0 ~ 63 30
WS32Z30/40 (32") CW29Z30/40 (29")
Data Data
28 → 30
15 → 11
42 → 32
42 → 32
16 → 14
32 → 30
32 → 30
16 → 14
32 → 30
32 → 30
30 FIX
11 FIX
32 FIX
32 FIX
14 FIX
30 FIX
30 FIX
14 FIX
30 FIX
30 FIX
Remark
Samsung Electronics 3-7
Alignment & Adjustment
9. VIDEO ADJUST 2
No item Range intial
0 ABL Mode 0~03 3 3 3 FIX
1 Gamma 0~03 0 0 2 FIX
2 ABL TH 0~15 14 14 3 FIX
3 AKB Time 0~31 15 15 15 FIX
4 S - ABL 3 3 3 FIX
5 P - ABL 6
6 VSU 0 0 0 FIX
7 LNA EXE 0 ~ 4 3 3 3 FIX
8 H_EHT comp 0~15 3 3 3 FIX
9 V_EHT comp 0~15 5 5 5 FIX
10 PIN EHT comp 0~07 3
11 AFC EHT comp 0~07 0 0 0 FIX
12 Sync Phase 0~1 0 0 0 FIX
13 Sync Phase (480) 0~1 1 1 1 FIX
14 Sync Phase (576P) 0~1 0 0 0 FIX
15 Sync Phase (720P) 0~1 1 1 1 FIX
16 Sync Phase (1080) 0~1 0 0 0 FIX
WS32Z30/40 (32") CW29Z30/40 (29")
Data Data
9 → 6
2 → 3
9 FIX
3 FIX
Remark
10. VIDEO ADJUST 3
No item Range intial
0 TNR Enable 0 ~ 1 1 1 1 FIX
1 TNR Chroma 0 ~ 15 10 11 10 FIX
2 TNR Luma 0 ~ 15 11 11 7 FIX
3 LTI Enable 0 ~ 1 1 1 1 FIX
4 LTI Gain 0 ~ 15 15 15 15 FIX
5 LTI Gain x2 0 ~ 1 1 1 1 FIX
6 LTI Coring 0 ~ 7 2
7 Lmix gain 3 3 3 FIX
8 Lmix offset 0 ~ 31 13
9 Peak Center Freq 0~3 3 3 3 FIX
10 Peaking Coring 0 ~ 31 2 2 2 FIX
11 CTI BW 0 ~ 1 4
12 CTI LP 0 ~ 1 1 1 1 FIX
13 CTI Gain 0 ~ 15 5 5 5 FIX
14 CTI Coring 0 ~ 15 2
15 V Peaking 0 ~ 15 3
16 V Peak Coring gain 0~7 0 0 0 FIX
17 V Peak high gain 0~15 0 0 0 FIX
18 V Peak coring high 0~15 0 0 0 FIX
19 IF Comp Filter 0 ~ 7 4 4 4 FIX
20 DHYAPRESC 0~3 2 2 2 FIX
21 DHCAPRESC 0~3 2 2 2 FIX
22 Neg Peaking 0 ~ 15 11 11 11 FIX
23 DCE Gain 0~255 45 45 45 FIX
24 CORBP 0~1 0 0 0 FIX
WS32Z30/40 (32") CW29Z30/40 (29")
Data Data
3 → 2
12 → 13
1 → 4
3 → 2
2 → 3
3 FIX
13 FIX
4 FIX
2 FIX
3 FIX
Remark
3-8 Samsung Electronics
Alignment & Adjustment
11. VIDEO ADJUST 4
No item Range intial
0 SVM RW 0 ~ 7 2 2 2 FIX
1 SVM Delay 0 ~ 7 0 0 0 FIX
2 SVM Coring 0 ~ 15 2 2 2 FIX
3 SVM Gain 0 ~ 63 45 45 45 FIX
4 SVM C_Gain 0 ~ 3 0 0 0 FIX
5 OSD Contrast 0 ~ 127 30 30 30 FIX
6 OSD Bright -512 ~ 511 127 127 127 FIX
7 TTX Contrast 0 ~ 127 17 17 17 FIX
8 TTX Bright ` 127 127 127 FIX
9 Melody Volume 0 ~ 127 10 10 10 FIX
10 VCR Mode Cnt 30 30 30 FIX
11 SLLTHD 2 2 2 FIX
12 SLLTHDV 3 3 3 FIX
13 THRSEL 0 0 0 FIX
14 LPCDEL 0 0 0 FIX
15 Pilot High 13 13 13 FIX
16 Pilot Low 7 7 7 FIX
17 AM_Prescale 22 22 22 FIX
WS32Z30/40 (32") CW29Z30/40 (29")
Data Data
Remark
Samsung Electronics 3-9
Alignment & Adjustment
12. Video Adjust5 (60i/100i)
No item Range
0 HORWIDTHP_H 5 5 5
1 HORWIDTHP_L 50 50 50 FIX
2 VERIWDTHP_H 1 1 1 FIX
3 VERIWDTHP_L 26 26 26 FIX
4 HORPOSP_H 1 1 1 FIX
5 HORPOSP_L 65 65 65 FIX
6 VERPOSP_H 0 0 0 FIX
7 VERPOSP_L 29 29 29 FIX
8 NAPPLIP_H 2 2 2 FIX
9 NAPPLIP_L 94 94 94 FIX
10 NALPFIP_H 0 0 0 FIX
11 NALPFIP_L 18 18 18 FIX
12 HSCPOSC_H 8 8 8 FIX
13 HSCPOSC_L 70 70 70 FIX
14 VSCPOSC_H 31 31 31 FIX
15 VSCPOSC_L 100 100 100 FIX
16 HORWIDTH_M_H 5 5 5 FIX
17 HORWIDTH_M_L 50 50 50 FIX
18 VERWIDTH_M_H 1 1 1 FIX
19 VERWIDTH_M_L 39 39 39 FIX
20 HORPOS_M_H 1 1 1 FIX
21 HORPOS_M_L 60 60 60 FIX
22 VERPOS_M_H 0 0 0 FIX
23 VERPOS_M_L 23 23 23 FIX
24 VSCPRESC_H 0 0 0 FIX
25 VSCPRESC_L 0 0 0 FIX
26 SD_BRTADJ 128 128 128 FIX
27 SD_CONADJ 32 32 32 FIX
28 SD_USATADJ 32 32 32 FIX
29 SD_VSATADJ 32 32 32 FIX
PAL_RF WS32Z30/40 (32") CW29Z30/40 (29")
Initial Data Data
Remark
3-10 Samsung Electronics
Alignment & Adjustment
13. Video Adjust5 (NTSC)
No item Range
0 HORWIDTHP_H 5 5 5
1 HORWIDTHP_L 75 75 75 FIX
2 VERIWDTHP_H 1 1 1 FIX
3 VERIWDTHP_L 235 235 235 FIX
4 HORPOSP_H 1 1 1 FIX
5 HORPOSP_L 50 50 50 FIX
6 VERPOSP_H 0 0 0 FIX
7 VERPOSP_L 30 30 30 FIX
8 NAPPLIP_H 2 2 2 FIX
9 NAPPLIP_L 18 18 18 FIX
10 NALPFIP_H 0 0 0 FIX
11 NALPFIP_L 10 10 10 FIX
12 HSCPOSC_H 8 8 8 FIX
13 HSCPOSC_L 45 45 45 FIX
14 VSCPOSC_H 12 12 12 FIX
15 VSCPOSC_L 20
16 HORWIDTH_M_H 5 5 5 FIX
17 HORWIDTH_M_L 88 88 88 FIX
18 VERWIDTH_M_H 2 2 2 FIX
19 VERWIDTH_M_L 5 5 5 FIX
20 HORPOS_M_H 1 1 1 FIX
21 HORPOS_M_L 30 30 30 FIX
22 VERPOS_M_H 0 0 0 FIX
23 VERPOS_M_L 10
24 VSCPRESC_H 4 4 4 FIX
25 VSCPRESC_L 0 0 0 FIX
26 SD_BRTADJ 128 128 128 FIX
27 SD_CONADJ 32 32 32 FIX
28 SD_USATADJ 32 32 32 FIX
29 SD_VSATADJ 32 32 32 FIX
NTSC WS32Z30/40 (32") CW29Z30/40 (29")
Initial Data Data
20 → 80
10 → 15
20 FIX
10 FIX
Remark
Samsung Electronics 3-11
Alignment & Adjustment
14. Video Adjust5 (576i)
No item Range
0 HORWIDTHP_H 5 5 5
1 HORWIDTHP_L 50 50 50 FIX
2 VERIWDTHP_H 1 1 1 FIX
3 VERIWDTHP_L 30 30 30 FIX
4 HORPOSP_H 1 1 1 FIX
5 HORPOSP_L 65 65 65 FIX
6 VERPOSP_H 0 0 0 FIX
7 VERPOSP_L 26 26 26 FIX
8 NAPPLIP_H 1 1 1 FIX
9 NAPPLIP_L 176 176 176 FIX
10 NALPFIP_H 0 0 0 FIX
11 NALPFIP_L 16 16 16 FIX
12 HSCPOSC_H 8 8 8 FIX
13 HSCPOSC_L 125 125 125 FIX
14 VSCPOSC_H 31 31 31 FIX
15 VSCPOSC_L 100 100 100 FIX
16 HORWIDTH_M_H 5 5 5 FIX
17 HORWIDTH_M_L 50 50 50 FIX
18 VERWIDTH_M_H 1 1 1 FIX
19 VERWIDTH_M_L 38 38 38 FIX
20 HORPOS_M_H 1 1 1 FIX
21 HORPOS_M_L 55 55 55 FIX
22 VERPOS_M_H 0 0 0 FIX
23 VERPOS_M_L 23 23 23 FIX
24 VSCPRESC_H 0 0 0 FIX
25 VSCPRESC_L 0 0 0 FIX
26 SD_BRTADJ 146 145 145
27 SD_CONADJ 46 45 45
28 SD_USATADJ 32 52 52
29 SD_VSATADJ 32 54 54
576i 576i_32" 576i_29"
Initial Data Data
Remark
3-12 Samsung Electronics
Alignment & Adjustment
15. Video Adjust5 (480i)
No item Range
0 HORWIDTHP_H 5 5 5
1 HORWIDTHP_L 48 48 48 FIX
2 VERIWDTHP_H 1 1 1 FIX
3 VERIWDTHP_L 246 246 246 FIX
4 HORPOSP_H 1 1 1 FIX
5 HORPOSP_L 60 60 60 FIX
6 VERPOSP_H 0 0 0 FIX
7 VERPOSP_L 21 21 21 FIX
8 NAPPLIP_H 1 1 1 FIX
9 NAPPLIP_L 101 101 101 FIX
10 NALPFIP_H 0 0 0 FIX
11 NALPFIP_L 16 16 16 FIX
12 HSCPOSC_H 8 8 8 FIX
13 HSCPOSC_L 125 125 125 FIX
14 VSCPOSC_H 12 12 12 FIX
15 VSCPOSC_L 0 0 0 FIX
16 HORWIDTH_M_H 5 5 5 FIX
17 HORWIDTH_M_L 48 48 48 FIX
18 VERWIDTH_M_H 1 1 1 FIX
19 VERWIDTH_M_L 241 241 241 FIX
20 HORPOS_M_H 1 1 1 FIX
21 HORPOS_M_L 41 41 41 FIX
22 VERPOS_M_H 0 0 0 FIX
23 VERPOS_M_L 24 24 24 FIX
24 VSCPRESC_H 4 4 4 FIX
25 VSCPRESC_L 0 0 0 FIX
26 SD_BRTADJ 146 146 146 FIX
27 SD_CONADJ 45
28 SD_USATADJ 52
29 SD_VSATADJ 52
480i 480i_32" 480i_29"
Initial Data Data
46 → 45
32 → 52
32 → 52
45 FIX
52 FIX
52 FIX
Remark
Samsung Electronics 3-13
Alignment & Adjustment
16. Video Adjust6 (comp_HD)
No item Range
0 HORWIDTHP_H 5 5 5 FIX
1 HORWIDTHP_L 45 45 45 FIX
2 VERWIDTHP_H 1 1 1 FIX
3 VERWIDTHP_L 226 226 226 FIX
4 HORPOSP_H 1 1 1 FIX
5 HORPOSP_L 104 104 104 FIX
6 VERPOSP_H 0 0 0 FIX
7 VERPOSP_L 26 26 26 FIX
8 DHSCPRESC_H 11 11 11 FIX
9 DHSCPRESC_L 100 100 100 FIX
10 DNAPPLIP_H 1 1 1 FIX
11 DNAPPLIP_L 11 11 11 FIX
12 DVOFPOSC 128 128 128 FIX
13 VERPOS_S 6 6 6 FIX
14 VEROFFS_S 0 0 0 FIX
15 HORPOS_S_H 1 1 1 FIX
16 HORPOS_S_L 41 41 41 FIX
HPULLINMODE 0 0 0 FIX
17 DVSCPOSC_HI 64 64 64 FIX
18 DVSCPOSC_LO_H 131 131 131 FIX
19 DVSCPOSC_LO_L 17 17 17 FIX
20 DHSCPOSC_HI 14 14 14 FIX
21 DHSCPOSC_LO 255 255 255 FIX
22 HD_BRTADJ 145 145 145 FIX
23 HD_CONADJ 45
24 HD_USATADJ 52
25 HD_VSATADJ 52
480P_HD 480P_HD_32" 480P_HD_29"
intial Data Data
47 → 45
32 → 52
32 → 52
45 FIX
52 FIX
52 FIX
Remark
3-14 Samsung Electronics
Alignment & Adjustment
17. Video Adjust6 (comp_HD)
No item Range
0 HORWIDTHP_H 5 5 5 FIX
1 HORWIDTHP_L 20 20 20 FIX
2 VERWIDTHP_H 2 2 2 FIX
3 VERWIDTHP_L 68 68 68 FIX
4 HORPOSP_H 1 1 1 FIX
5 HORPOSP_L 85 85 85 FIX
6 VERPOSP_H 0 0 0 FIX
7 VERPOSP_L 26 26 26 FIX
8 DHSCPRESC_H 11 11 11 FIX
9 DHSCPRESC_L 210 210 210 FIX
10 DNAPPLIP_H 1 1 1 FIX
11 DNAPPLIP_L 35 35 35 FIX
12 DVOFPOSC 100 100 100 FIX
13 VERPOS_S 5 5 5 FIX
14 VEROFFS_S 6 6 6 FIX
15 HORPOS_S_H 1 1 1 FIX
16 HORPOS_S_L 1 1 1 FIX
HPULLINMODE 0 0 0 FIX
17 DVSCPOSC_HI 64 64 64 FIX
18 DVSCPOSC_LO_H 66 66 66 FIX
19 DVSCPOSC_LO_L 203 203 203 FIX
20 DHSCPOSC_HI 14 14 14 FIX
21 DHSCPOSC_LO 215 215 215 FIX
22 HD_BRTADJ 146
23 HD_CONADJ 46
24 HD_USATADJ 53
25 HD_VSATADJ 54
576P_HD 576P_HD_32" 576P_HD_29"
intial Data Data
145 → 146
47 → 46
32 → 53
32 → 54
146 FIX
46 FIX
53 FIX
54 FIX
Remark
Samsung Electronics 3-15
Alignment & Adjustment
18. Video Adjust6 (comp_HD)
No item Range
0 HORWIDTHP_H 4 4 4 FIX
1 HORWIDTHP_L 226 226 226 FIX
2 VERWIDTHP_H 2 2 2 FIX
3 VERWIDTHP_L 125 125 125 FIX
4 HORPOSP_H 1 1 1 FIX
5 HORPOSP_L 50 50 50 FIX
6 VERPOSP_H 0 0 0 FIX
7 VERPOSP_L 26 26 26 FIX
8 DHSCPRESC_H 2 2 2 FIX
9 DHSCPRESC_L 30 30 30 FIX
10 DNAPPLIP_H 0 0 0 FIX
11 DNAPPLIP_L 240 240 240 FIX
12 DVOFPOSC 128 128 128 FIX
13 VERPOS_S 6 6 6 FIX
14 VEROFFS_S 0 0 0 FIX
15 HORPOS_S_H 1 1 1 FIX
16 HORPOS_S_L 15 15 15 FIX
HPULLINMODE 1 1 1 FIX
17 DVSCPOSC_HI 71 71 71 FIX
18 DVSCPOSC_LO_H 60 60 60 FIX
19 DVSCPOSC_LO_L 178 178 178 FIX
20 DHSCPOSC_HI 15 15 15 FIX
21 DHSCPOSC_LO 255 255 255 FIX
22 HD_BRTADJ 142
23 HD_CONADJ 50 50 50 FIX
24 HD_USATADJ 50
25 HD_VSATADJ 50
720P 50_HD 720P 50_HD_32" 720P 50_HD_29"
intial Data Data
144 → 142
32 → 50
32 → 50
142 FIX
50 FIX
50 FIX
Remark
3-16 Samsung Electronics
Alignment & Adjustment
19. Video Adjust6 (comp_HD)
No item Range
0 HORWIDTHP_H 4 4 4 FIX
1 HORWIDTHP_L 225 225 225 FIX
2 VERWIDTHP_H 2 2 2 FIX
3 VERWIDTHP_L 16 16 16 FIX
4 HORPOSP_H 1 1 1 FIX
5 HORPOSP_L 53 53 53 FIX
6 VERPOSP_H 0 0 0 FIX
7 VERPOSP_L 26 26 26 FIX
8 DHSCPRESC_H 3 3 3 FIX
9 DHSCPRESC_L 210 210 210 FIX
10 DNAPPLIP_H 0 0 0 FIX
11 DNAPPLIP_L 214 214 214 FIX
12 DVOFPOSC 128 128 128 FIX
13 VERPOS_S 24 24 24 FIX
14 VEROFFS_S 1
15 HORPOS_S_H 0 0 0 FIX
16 HORPOS_S_L 240 240 240 FIX
HPULLINMODE 1 1 1 FIX
17 DVSCPOSC_HI 85 85 85 FIX
18 DVSCPOSC_LO_H 70
19 DVSCPOSC_LO_L 255 255 255 FIX
20 DHSCPOSC_HI 14 14 14 FIX
21 DHSCPOSC_LO 162 162 162 FIX
22 HD_BRTADJ 142
23 HD_CONADJ 50 50 50 FIX
24 HD_USATADJ 50
25 HD_VSATADJ 50
720P 60_HD 720P 60_HD_32" 720P 60_HD_29"
intial Data Data
0 → 1
70 → 90
144 → 142
32 → 50
32 → 50
0 FIX
70 FIX
142 FIX
50 FIX
50 FIX
Remark
Samsung Electronics 3-17
Alignment & Adjustment
20. Video Adjust6 (comp_HD)
No item Range
0 HORWIDTHP_H 4 4 4 FIX
1 HORWIDTHP_L 220 220 220 FIX
2 VERWIDTHP_H 2 2 2 FIX
3 VERWIDTHP_L 129 129 129 FIX
4 HORPOSP_H 0 0 0 FIX
5 HORPOSP_L 250 250 250 FIX
6 VERPOSP_H 0 0 0 FIX
7 VERPOSP_L 26 26 26 FIX
8 DHSCPRESC_H 15 15 15 FIX
9 DHSCPRESC_L 30 30 30 FIX
10 DNAPPLIP_H 0 0 0 FIX
11 DNAPPLIP_L 0 0 0 FIX
12 DVOFPOSC 128 128 128 FIX
13 VERPOS_S 6 6 6 FIX
14 VEROFFS_S 0 0 0 FIX
15 HORPOS_S_H 0 0 0 FIX
16 HORPOS_S_L 131 131 131 FIX
HPULLINMODE 1 1 1 FIX
17 DVSCPOSC_HI 53 53 53 FIX
18 DVSCPOSC_LO_H 69 69 69 FIX
19 DVSCPOSC_LO_L 255 255 255 FIX
20 DHSCPOSC_HI 13 13 13 FIX
21 DHSCPOSC_LO 246 246 246 FIX
22 HD_BRTADJ 143
23 HD_CONADJ 49 49 49 FIX
24 HD_USATADJ 50
25 HD_VSATADJ 50
1080i 50_HD 1080i 50_HD_32" 1080i 50_HD_29"
intial Data Data
145 → 143 145 → 143
32 → 50 32 → 50
32 → 50 32 → 50
Remark
FIX
FIX
FIX
3-18 Samsung Electronics
Alignment & Adjustment
21. Video Adjust6 (comp_HD)
No item Range
0 HORWIDTHP_H 5 5 5 FIX
1 HORWIDTHP_L 30 30 30 FIX
2 VERWIDTHP_H 2 2 2 FIX
3 VERWIDTHP_L 17 17 17 FIX
4 HORPOSP_H 0 0 0 FIX
5 HORPOSP_L 180 180 180 FIX
6 VERPOSP_H 0 0 0 FIX
7 VERPOSP_L 26 26 26 FIX
8 DHSCPRESC_H 14 14 14 FIX
9 DHSCPRESC_L 130 130 130 FIX
10 DNAPPLIP_H 0 0 0 FIX
11 DNAPPLIP_L 100 100 100 FIX
12 DVOFPOSC 128 128 128 FIX
13 VERPOS_S 6 6 6 FIX
14 VEROFFS_S 0 0 0 FIX
15 HORPOS_S_H 0 0 0 FIX
16 HORPOS_S_L 190 190 190 FIX
HPULLINMODE 1 1 1 FIX
17 DVSCPOSC_HI 64 64 64 FIX
18 DVSCPOSC_LO_H 0 0 0 FIX
19 DVSCPOSC_LO_L 183 183 183 FIX
20 DHSCPOSC_HI 14 14 14 FIX
21 DHSCPOSC_LO 66 66 66 FIX
22 HD_BRTADJ 143
23 HD_CONADJ 49 49 49 FIX
24 HD_USATADJ 50
25 HD_VSATADJ 50
1080i 60_HD 1080i 60_HD_32" 1080i 60_HD_29"
intial Data Data
145 → 143 145 → 143
32 → 50 32 → 50
32 → 50 32 → 50
Remark
FIX
FIX
FIX
Samsung Electronics 3-19
Alignment & Adjustment
22. VIDEO ADJUST 7(color tone setting)
No item Range intial
0 R drive offset Warm2 -20~+20 3
1 B drive offset Warm2 -20~+20 -9 -9 -9 FIX
2 R cutoff offset Warm2 -20~+20 6 6 6 FIX
3 B cutoff offset Warm2 -20~+20 -11 -11 -11 FIX
4 R drive offset Warm1 -20~+20 2
5 B drive offset Warm1 -20~+20 -2
6 R cutoff offset Warm1 -20~+20 3
7 B cutoff offset Warm1 -20~+20 -2
8 R drive offset Normal -20~+20 0 0 0 FIX
9 B drive offset Normal -20~+20 0 0 0 FIX
10 R cutoff offset Normal -20~+20 0 0 0 FIX
11 B cutoff offset Normal -20~+20 0 0 0 FIX
12 R drive offset Cool 1 -20~+20 0
13 B drive offset Cool 1 -20~+20 4 4 4 FIX
14 R cutoff offset Cool 1 -20~+20 2
15 B cutoff offset Cool 1 -20~+20 6 6 6 FIX
16 R drive offset Cool 2 -20~+20 -2 -2 -2 FIX
17 B drive offset Cool 2 -20~+20 6 6 6 FIX
18 R cutoff offset Cool 2 -20~+20 0 0 0 FIX
19 B cutoff offset Cool 2 -20~+20 9 9 9 FIX
WS32Z30/40 (32") CW29Z30/40 (29")
Data Data
3 → 8
2 → 4
-2 → -3
3 → 4
-2 → -3
0 → -5
2 → 0
8 FIX
4 FIX
-3 FIX
4 FIX
-3 FIX
-5 FIX
0 FIX
Remark
3-20 Samsung Electronics
Loading...