Samsung WS32Z10HVTXBWT Service Manual
COLOR TELEVISION RECEIVER
Chassis : S58A(P)
Model : WS32Z10HVTXBWT
COLOR TELEVISION RECEIVER CONTENTS
Alignment and Adjustments
Exploded Views and Parts List
Electrical Parts List
PCB Diagram
Schematic
1.
2.
3.
4.
5.
ELECTRONICS
© Samsung Electronics Co., Ltd. Feb. 2003
Printed in Korea
AA82-00398A
Alignment and Adjustments
Samsung Electronics 1-1
1. Alignment and Adjustments
1-1 Adjustments
Usually, a color TV needs only slight touch-up adjustment upon installation. Check the basic
characteristics such as vertical size, horizontal size, and focus. Observe the picture and check for
good black and white details. There must be no objectionable color shading: If color shading is
present, demagnetize the receiver. If color shading persists, re-do purity and convergence adjustments.
Note :
1. This ‘4. Alignment and Adjustments’ applies to S58A chassis applications.
2. AC Power Supply: 100~230 V
3. This service manual has been written on the basis of domestic remote-control model adopting S58A
chassis. Depending on sales location and product specifications, some of specifications herein may
be changed.
S58A contains a dynamic focus circuit. When CRT PCB, FBT or CRT is replaced, be sure to adjust
in the following sequence:
1-1-1 General Alignment Instructions
1-1-2 Focus Adjustment
Dynamic Focus Adjustment
1. Input a crosshatch pattern.
2. Select “Standard” from the menu,
3. Turn the Static Focus VR clockwise to set it to its maximum.
4. Turn the Dynamic Focus VR counterclockwise to set it to its
maximum.
5. Turn the Static Focus VR counterclockwise slowly for the clearest
center vertical line.
STATIC FOCUS VR
DYNAMIC FOCUS VR
H
V
NO USE
<FBT FOCUS PACK>
After Adjustment
6. Turn the Dynamic Focus VR clockwise slowly for the clearest third line.
1
2
3
7. Check for the FOCUS of entire screen. If necessary, re-do adjustments 3~6.
Alignment and Adjustments
1-2 Samsung Electronics
1-1-3 Screen Voltage Adjustment
1. Use a DC multi-meter to identify RK, GK, BK. And then adjust FBT Screen VR so that the highest
voltage becomes 175 Vp-p.
1-1-4 White Balance Adjustment
1. Select “Standard” from the menu.
2. Input an 100% White pattern.
3. In standby, press the remote-control keys in the following sequence:
Display Menu,Mute, Power on the TV set.
4. Warm up the TV set at least for 30 minutes.
5. Input a stair signal.
6. Use the Volume +/- buttons on the remote-control to select R Drive,G Drive,B Drive,Sub Cont.
7. Adjust Low-Light while viewing the darker side of screen.
8. Use the Volume +/- buttons on the remote-control to select Rcutoff,Gcutoff,Bcutoff,Sub Brt.
9. Adjust High-Light while viewing the brighter side of screen.
10. If not proper, re-adjust White Balance.
11. Press the Memory button to exit.
1-1-5 Sub-Brightness Adjustment
1. In standby, press the remote-control keys in the following sequence:
Display Menu Mute Power on the TV set.
2. Use the Channel Up/Down buttons to receive the sub bright adjustment signal.
3. Use the Volume +/- buttons to select SBT.
4. Press the Menu or Mute button on the remote control to adjust so that the seventh step on
the right of screen cannot be seen.
5. Press the Memory button to exit.
Alignment and Adjustments
Samsung Electronics 1-3
1-2 MICOM PINNING
P-MQFP-128-2
M2
12345678910111213141516171819202122232425262728293031
32
96959493929190898887868584838281807978777675747372717069686766
65
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
D5
D9
D13
V
DD33-5
V
SS33-5
D1
D6
D8
D14
D0
D7
V
DD33-4
V
SS33-4
D15
WR
LDQM
UDQM
RD
CSROM
CLKEN
CSSDRAM
MEMCLK
V
DD33-3
V
SS33-3
A15/CAS
A14/RAS
A13
A0
A1
A2
A3
A4
P6.1
P6.0
P5.15
P5.14
P3.15
P3.13
P3.12
P3.11
P3.10
V
DD25-2VSS25-2VDD33-7VSS33-7
P3.9
P3.8
P3.7
P3.6
P3.5
P3.4
P3.3
P3.2
P3.1
P3.0
RSTIN
D11D3D4
V
DD33-6VSS33-6
D10
D12
D2
TCK
TMS
TDI
TDO
P2.8
P2.9
P2.10
P2.11
P2.12
P2.13
P2.14
P2.14
P2.15
V
SS33-1
V
DD33-1
P4.5/CS3
P4.4/A20
P4.3/A19
P4.2/A18
P4.1/A17
V
SS25-1
V
DD25-1
P4.0/A16
A8A7A6
A5
A10
A11
A12
V
SS33-2
V
DD33-2
P6.2
P6.3
P6.4
P6.5
P6.6
VSYNC
HSYNC
COR/RSOUT
LANK/CORBLA
V
DD33-8
V
SS33-8
XTAL1
XTAL2
V
SSA-1
V
DDA-1
R
G
B
V
SSA-2
V
DDA-2
CVBS2
V
SSA-3
V
DDA-3
CVBS1B
CVBS1A
V
SSA-4
V
DDA-4
P5.0
P5.1
P5.2
P5.3
TMODE
1-2-1 MICOM PINNING (SDA6001 B12)
Alignment and Adjustments
1-4 Samsung Electronics
1-2-2 MICOM MODULE PIN ALIGNMENT
1-2-3 M2 VCC & GND
PIN NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
PAL MODULE
SC1-ID(AV1/DVD1-ID)
SC2-ID ( AV2 )
SC3-ID(AV3/AV3S-ID)
F/B SW1
F/B SW2
SDA3
SCL3
GND
5VB
GND
HS2
VS2
GND
OSD/TTX-F/B
OSD/TTX-R
OSD/TTX-G
OSD/TTX-B
DTV/DVD2-ID
V-RESET
TTX CVBS
GND
MAIN AFT
PIN NO
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
PAL MODULE
MT SW1
MT SW2
PT SW1
PT SW2
GND
SDA1
SCL1
DEF SW1
DEF SW2
DEF SW3
GND
SPOT
SDA2
SCL2
WP/STOP
S-RESET2
STD 5V
HDD_TEMP
LED1
LED2
TILT
1080i SW
PIN NO
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
PAL MODULE
GND
D-COIL
MAIN_POWER
FAV-ID/FS-ID
HEADPHONE-ID
S-MUTE
S-RESET
GND
VGA-ID
KEY1
KEY2
IR
GND
DVR CON. CLOCK
DVR CON. STROBE
DVR CON. DATA OUT
DVR CON. DATA IN
DVRSTD_POWER
SUB_POWER
DVR RESET
Standy by
Operation
GND
2.5V
2.5V
3.3V
Digital
Analog
Pin(Voltage, Description)
- Digital : 21,87 (Digital core)
- Analog : 111
- Analog : 116,119,123
- Digital : 14,32,42,53,61,69,85,106
- 20,86
- 13,31,41,52,60,68,85,107
-110
-115,118,122
Current
150mA
100mA
150mA
-
-
-
-
Remark
- Idel mode : 2.5mA
- Digital core(2.5V)
- for pads (3.3V)
- 2.5V
- 2.5V
Alignment and Adjustments
Samsung Electronics 1-5
1-2-4 MICOM PORT ASSIGNMENT
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
FUNCTION
TCK
TMS
TDI
TDO
P2.8/EXT0 IN
P2.9/EXT1 IN
P2.10/EXT2 IN
P2.11/EXT3 IN
P2.12/EXT4 IN
P2.13/EXT5 IN
P2.14/EXT6 IN
P2.15/EXT7 IN
VSS33
VDD33
P4.5/CS3
P4.4/A20
P4.3/A19
P4.2/A18
P4.1/A17
VSS25
VDD25
P4.0/A16
A8
A7
A9
A6
A5
A10
A11
A12
VSS33
VDD33
A4
A3
ASSIGN
TCK
TMS
TDI
TDO
NC
PVRSTD_PO
S3PRESET
5VB CHECK
DATA IN
DATA OUT
STROBE
CLOCK
DGND
3.3V
CS3
A20
A19
A18
A17
2.5V
A16
A8
A7
A9
A6
A5
A10
A11
A12
DGND
3.3V
A4
A3
IN/OUT
IN
IN
IN
OUT
OUT
OUT
IN
IN
OUT
OUT
OUT
-
OUT
OUT
OUT
OUT
OUT
-
-
IN/OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
-
OUT
OUT
ACTIVE H/L
-
-
-
-
LOW
HIGH
-
-
-
-
-
LOW
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
EXPLANATION
CLOCK FOR JTAC INTERFACE
CONTROL SIGNAL FOR JTAG INTERFACE
DATA INPUT FOR JTAG INTERFACE
DATA OUTPUT FOR JTAG INTERFACE
DVR STAND-BY REGULATOR SWITCHING CONTROL
S3P9428 RESET
SLAVE VCC CHECK POINT
DVR CONTROL DATA IN
DVR CONTROL DATA OUT
DVR CONTROL STROBE
DVR CONTROL CLOCK
DIGITAL GND FOR PADS
DIGITAL VCC FOR PADS
CHIP SELECT FOR SECOND STATIC MEMORY
EXT MEMORY ADDRESS BIT20
EXT MEMORY ADDRESS BIT19
EXT MEMORY ADDRESS BIT18
EXT MEMORY ADDRESS BIT17
DIGITAL GND FOR DIGITAL CORE
DIGITAL VCC FOR DIGITAL CORE
BOOTSTRAP CONTROL / EXT MEMORY ADDRESS BIT17
EXT MEMORY ADDRESS BIT8
EXT MEMORY ADDRESS BIT7
EXT MEMORY ADDRESS BIT9
EXT MEMORY ADDRESS BIT6
EXT MEMORY ADDRESS BIT5
EXT MEMORY ADDRESS BIT10
EXT MEMORY ADDRESS BIT11
EXT MEMORY ADDRESS BIT12
DIGITAL GND FOR PADS
DIGITAL VCC FOR PADS
EXT MEMORY ADDRESS BIT4
EXT MEMORY ADDRESS BIT3
Alignment and Adjustments
1-6 Samsung Electronics
NO
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
FUNCTION
A2
A1
A0
A13
A14/RAS
A15/CAS
VSS33
VDD33
MEMCLK
CSSDRAM
CLKEN
CSROM
RD
UDQM
LDQM
WR
D15
VSS33
VDD33
D7
D0
D14
D8
D6
D1
VSS33
VDD33
D13
D9
D5
D2
D12
ASSIGN
A2
A1
A0
A13
A14/RAS
A15/CAS
DGND
3.3V
CLK-SDRAM
CS-SDRAM
CLK-ENABLE
CS-ROM
RD-ROM
WR-DISABLE
WR-DISABLE
WR
D15
DGND
3.3V
D7
D0
D14
D8
D6
D1
DGND
3.3V
D13
D9
D5
D2
D12
IN/OUT
OUT
OUT
OUT
OUT
OUT
OUT
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
ACTIVE H/L
-
-
-
-
-
-
-
-
-
LOW
LOW
LOW
LOW
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
EXPLANATION
EXT MEMORY ADDRESS BIT2
EXT MEMORY ADDRESS BIT1
EXT MEMORY ADDRESS BIT0
EXT MEMORY ADDRESS BIT13
EXT MEMORY ADDRESS BIT14/ROW ADDRESS
STROBE FOR SDRAM
EXT MEMORY ADDRESS BIT15/COLUMN
ADDRESS STROBE FOR SDRAM
DIGITAL GND FOR PADS
DIGITAL VCC FOR PADS
100MHZ CLOCK FOR SDRAM
CHIP SELECT FOR SDRAM MEMORY
ENABLE FOR SDRAM MEMORY CLOCK
CHIP SELECT FOR ROM
EXTERNAL MEMORY READ STROBE FOR ROM
WRITE DISABLE FOR HIGHBYTE
WRITE DISABLE FOR LOWBYTE
WRITE ENABLE FOR FOR SDRAM
EXT MEMORY DATA BIT15
DIGITAL GND FOR PADS
DIGITAL VCC FOR PADS
EXT MEMORY DATA BIT7
EXT MEMORY DATA BIT0
EXT MEMORY DATA BIT14
EXT MEMORY DATA BIT8
EXT MEMORY DATA BIT6
EXT MEMORY DATA BIT1
DIGITAL GND FOR PADS
DIGITAL VCC FOR PADS
EXT MEMORY DATA BIT13
EXT MEMORY DATA BIT9
EXT MEMORY DATA BIT5
EXT MEMORY DATA BIT2
EXT MEMORY DATA BIT12
Alignment and Adjustments
Samsung Electronics 1-7
NO
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
FUNCTION
D10
VSS33
VDD33
D4
D3
D11
RSTIN
P3.0/SCL0
P3.1/SDA0
P3.2/CAPIN
P3.3/T3OUT
P3.4/T3EUD
P3.5/T4IN
P3.6/T3IN
P3.7/T2IN
P3.8/MRST
P3.9/MTSR
VSS33
VDD33
VSS25
VDD25
P3.10/TXD0
P3.11/RXD0
P3.12/LED1
P3.13/SCLK
P3.15/LED2
P5.14/T4EUD
P5.15/T2EUD
P6.0/TRIG_IN
P6.1/TRIG_OUT
P6.2/SDA01
P6.3/SCL01
P6.4/SDAI1
P6.5/SCLI1
ASSIGN
D10
DGND
3.3V
D4
D3
D11
RESET
SCL2
SDA2
IR
SUB POWER
MAIN POWER
DVR RESET
WP
S-RESET
S-MUTE
NC
DGND
3.3V
DGND
2.5V
D-COIL
V_RESET
LED1
LED2
S3PRESET
NC
NC
BRK-IN
BRK-OUT
NC
SCL1
SDA1
SCL3
IN/OUT
-
-
-
-
-
-
IN
IN/OUT
IN/OUT
IN
OUT
OUT
OUT
IN
OUT
OUT
-
-
-
-
OUT
OUT
OUT
OUT
OUT
-
-
IN
OUT
-
IN/OUT
IN/OUT
IN/OUT
ACTIVE H/L
-
-
-
-
-
-
LOW
-
-
LOW
LOW
LOW
LOW
LOW
HIGH
-
-
-
-
-
HIGH
HIGH
HIGH
HIGH
HIGH
-
-
-
-
-
-
-
-
EXPLANATION
EXT MEMORY DATA BIT10
DIGITAL GND FOR PADS
DIGITAL VCC FOR PADS
EXT MEMORY DATA BIT4
EXT MEMORY DATA BIT3
EXT MEMORY DATA BIT11
MICOM HARDWARE RESET
EEPROM CONTROL SERIAL CLOCK LINE
EEPROM CONTROL SERIAL DATA LINE
REMOCON IN
SUB POWER PORT ON/OFF CONTROL(FOR PVR)
MAIN POWER PORT ON/OFF CONTROL
DVR BOARD RESET
IIC STOP & EEPROM WRITE PROTECTION
MSP34XX / DPL3519 & AC3 HARDWARE
RESET CONTROL
SOUND AMP MUTE
DIGITAL GND FOR PADS
DIGITAL VCC FOR PADS
DIGITAL GND FOR DIGITAL CORE
DIGITAL VCC FOR DIGITAL CORE
DEGAUSSING COIL CONTROL
SNI RESET FOR VIDEO PROCESSING IC
STAND-BY LED CONTROL
TIMER LED CONTROL
S3P9428 RESET
JTAG BRK IN
JTAG BRK OUT
SLAVE IC CONTROL SERIAL CLOCK LINE
SLAVE IC CONTROL SERIAL DATA LINE
IIC3 CONTROL CLOCK
Alignment and Adjustments
1-8 Samsung Electronics
NO
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
FUNCTION
P6.6/SDA2
VSYNC/VCS
HSYNC
COR/RSTOUT
BLANK/CORBLA
VDD33
VSS33
XTAL1
XTAL2
VSSA
VDDA
R
G
B
VSSA
VDDA
CVBS2
VSSA
VDDA
CVBS1B
CVBS1A
VSSA
VDDA
P5.0/AN.0
P5.1/AN.1
P5.2/AN.2
P5.3/AN.3
TMODE
ASSIGN
SDA3
V-SYNC
H-SYNC
H/T
OSD-F/B
3.3V
DGND
XTAL-IN
XTAL-OUT
AGND
2.5V
OSD-R
OSD-G
OSD-B
AGND
2.5V
GND
AGND
2.5V
GND
TTX-CVBS
AGND
2.5V
KEY1
KEY2
M-AFT
NC
GND
IN/OUT
IN/OUT
IN
IN
OUT
OUT
-
-
IN
OUT
-
IN
OUT
OUT
OUT
-
IN
-
-
IN
-
IN
IN
IN
IN
IN
-
-
ACTIVE H/L
-
HIGH
HIGH
HIGH
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
EXPLANATION
IIC3 CONTROL DATA
MAIN PICTURE VERTICAL SYNC IN FOR OSG POSITION
MAIN PICTURE HORIZONTAL SYNC IN FOR OSG
POSITION
HALFTONE SIGNAL OUT(NC)
OSD F/B & HALFTONE SIGNAL OUT
DIGITAL VCC FOR PADS
DIGITAL GND FOR PADS
MICOM CRISTAL OSC IN(6MHZ)
MICOM CRISTAL OSC OUT(6MHZ)
ANALOG GND
STD-BY ANALOG POWER
2 LAYER OSG RED OUT
2 LAYER OSG GREEN OUT
2 LAYER OSG BLUE OUT
ANALOG GND
ANALOG POWER
CVBS2 GND
ANALOG GND
ANALOG POWER
CVBS1 GND WITH 75 ohm
CVBS INPUT FOR TELETEXT DECODING
ANALOG GND
ANALOG POWER FOR ADC
VOLUME UP/DOWN, CHANNEL UP/DOWN KEY IN
MENU, TV/VIDEO, NT POWER KEY IN
MAIN TUNER AFT VOLTAGE
GND WITH 10K ohm IN NORMAL CONDITION
Alignment and Adjustments
Samsung Electronics 1-9
1-2-5 S3P9428 PINNING(I/O EXPANDER)
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
PIN NAME
VSS
XIN
XOUT
TEST
P0.1
P0.0
RESET
P3.0
P3.2
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
AVSS
AVREF
P2.6
P2.7
P1.3
P1.2
P1.1
P1.0
P3.3
P3.1
P0.7
P0.6
P0.5
P0.4
P0.3
P0.2
VDD
FUNCTION
GND
X-TAL IN
X-TAL OUT
I/O
I/O
RESET
S_RESET2
Output
I/O,ADC
I/O,ADC
I/O,ADC
I/O,ADC
I/O,ADC
ADDRESS
ANALOG GND
ADC REF
SDA
SCL
I/O,PWM
I/O
I/O
I/O
Output
Output
I/O,ADC,PWM
I/O,ADC
I/O,ADC
I/O,ADC
I/O
I/O
5V
ASSIGN
GND
X-TAL IN
X-TAL OUT
GND
HEADPHONE-ID
VGA-ID
RESET
RESET
SPOT
MT SW1
MT SW2
PT SW1
PT SW2
HDD_TEMP
GND
GND
ADC REF
SDA2
SCL2
TILT
DEF SW3
DEF SW1
DEF SW2
F/B SW1
F/B SW2
SC3-ID(AV3/AV3S-ID)
SC1-ID(AV1/DVD1-ID)
SC2-ID ( AV2 )
FAV-ID/FS-ID
DTV/DVD2-ID
1080i SW
STD 5V
IN/OUT
-
-
-
IN
IN
IN
OUT
OUT
OUT
OUT
OUT
OUT
IN
-
-
-
-
-
OUT
OUT
OUT
OUT
OUT
OUT
IN
IN
IN
IN
IN
OUT
-
ACTIVE
-
-
-
LOW
LOW
LOW
LOW
HIGH
-
-
-
-
-
-
PWM
HIGH/LOW
HIGH
HIGH
LEVEL
CHANGE
HIGH
LOW
-
EXPLANATION
-
12MHZ
H.P JACK ID
VGE SIGNAL ID
S3P9428 MICOM RESET
MSP3410 RESET
SPOT KILLER
MAIN TUNER S/W
MAIN TUNER S/W
PIP TUNER S/W
PIP TUNER S/W
Inside Temperature A/D Input CHECK
ADDRESS GND
ANALOG GND
ADC REF
IIC CONTROL
DTV / RF SIGNAL SWITCH
CXA2156 DEFLECTION FREQUENCY CONTROL
CXA2156 DEFLECTION FREQUENCY CONTROL
MSP4450G D/A OUT PIN
MSP4450G D/A OUT PIN
AV3 SIGNAL ID
AV1/EVE1 SIGNAL ID
AV2 SIGNAL ID
FAV/F S-VHS SIGNAL ID
DVD2/DTV SIGNAL ID
DTV 1080i MODE S/W
SYSTEM YCC
Alignment and Adjustments
1-10 Samsung Electronics
1-2-6 ADC INPUT VOLTAGE
PIN NO
26
27
28
29
ASSIGN
SC3-ID(AV3/AV3S-ID)
SC1-ID(AV1/DVD1-ID)
SC2-ID ( AV2 )
FAV-ID/FS-ID
0 ~ 1.5
NOT CON.
NOT CON.
NOT CON.
1.6 ~ 3.4
WIDE MODE
WIDE MODE
WIDE MODE.
0 ~ 1.5
NOT CON.
NOT CON.
NOT CON.
0 ~ 2.2
NOT CON.
AV3 SVHS
NOT CONNECTION
FRONT-SVHS
Use the same valtage as RCA option
AV2
2.3 ~ 2.9
DVD1
3.0 ~ 4.0
NOT CON.
AV1
NOT CON.
4.1 ~ 5.0
AV3
ALL CON.
F-VIDEO
SCART JACK MODEL OPTION IDENT
VOLTAGE(V)
RCA JACK MODEL IDENT VOLTAGE(V)
Alignment and Adjustments
Samsung Electronics 1-11
1-2-7 MICOM FACTORY MODE OPTION BYTE
ITEM OPTION BYTE
00 CRT
01 Language Group
02 Language
03 ATM
04 Scart/Rca
05 Plug&Play
06 Teleweb
07 CS/CW
08 Ln a
09 H/P JACK IDENT
10 TOP TTX
11 High Deviation
12 TTX Group
13 Carrier Mute
14 P . Standard
15 Digital NR
16 Speaker Include?
17 AG C
18 DNle
19 DV R
20 SAMSUNG LOGO
21 Auto format
CIS
Wide
Europe
Russian
On
Scart
On
Off
CS
On
High
Off
Off
Russian
Off
Dynamic
On
Yes
Off
On
Off
On
Off
Europe
Wide
Europe
English
On
Scart
On
On
CW
On
HIgh
Off
Off
W-Europe
Off
Dynamic
On
Yes
Off
On
Off
On
On
INITIAL
VALUE
Wide
Europe
English
On
Scart
On
Off
CS
On
HIgh
Off
Off
W-Europe
Off
Dynamic
On
Yes
Off
Off
On
On
Off
Remark
-CPT Option(Wide/4:3):P.Size format, WSS Related Option
-User Optional Language Group Setting(Europe/Asia)
-Refer to “Language Group Table”
-Select the language of destination from Language Group
* Note: Countermeasute to prevent IRAN from smuggling Once
Arabic(Persian)has been selected,the user can’t select Persian(Arabic)
-ON: ATM, OFF: Auto search
-SCART: AV-Link,AV Setup Menu, Scart jack switching
-RCA: RCA Jack switching, DVD
-Application of Dolby Prologic((On/Off)
-Dependin on area.(West Europe : On, East Europe : Off)
-CW/CS Tuner switching option
-Application of LNA(Pinp model) (On/Off)
-ON:The main sound is cut off after identigying the headphome jack
-OFF:The headphome jack ident PIN of MICOM is used as an IIC STOP
PIN. The main sound is not cut off
-Set only the countries requesting TOP patent so that TOP TTX
can be available(Countries using TOP:Germany,Austria,Italy,Swiss)
-Solve the Sound Stop problem by tutning High Deviation On for the
countries with SOUND over modulation
-Grouping the TTX Language by Region:Refer to a separate TABLE
-For Italy Only (Option)
-Mode of Picture Statues
-Application of Digital Noise Reduction(On/Off)
-Different by Cabinet(Z10:Yes, A10:No)
-Automatic Gain Control
-Digital Natural Image engine
-DVR on/off
-AV mode No signal
- Auto format
China
Wide
Asia
Chineses
Off
RCA
On
Off
CS
On
High
Off
Off
W-Europe
Off
Dynamic
Off
Off
On
On
On
Off
Southeast
ASIA
Wide
Asia
Country
Off
RCA
On
Off
CS
On
High
Off
Off
W-Europe
Off
Dynamic
Off
Off
On
On
On
Off
Refer to Remark
Alignment and Adjustments
1-12 Samsung Electronics
1-3 FACTORY MODE CONTROL
1. Enter & Concel the Factory Mode
1) Usual Remote Control
Enter : PICTURE OFF -> DISPLAY KEY -> MENU KEY -> MUTE KEY
(Press each remote control key with in 3 seconds)
Cannel : POWER OFF -> ON
2) Factory Remote Control
Enter : DISPLAY KEY -> FACTORY KEY
(Press each remote control key with in 3 seconds)
Cannel : POWER OFF -> ON
Press the FACTORY key twice at intervals of at lease 1 second.
(Enter the AGING Mode once)
3) Set Value When Entering the Factory Mode
- Picture Mode & Sound Mode are set to the
dynamic mode data
- Scan Mode : Natual Scan(NT/PAL All)
- Brigntness : 50 Contrast : 90 Bright : 50 Color : 50
sharpness : 60 Color tone : Center
4) Adjustments
- CH. UP/DOWN Key : Use to select the item you want
- VOLUME UP/DOWN Key : Increases or decreases the value of data.
- MENU Key : Use to save the current set value in EEPROM and exit to the upper mode.
- Use the DIGIT Key to switch channels
- Use the TV/VIDEO Key th conver to the AV Mode
1-3-1 Factroy Mode Data Control
1-4 FACTORY ADJUSTMENT DATA
OPTION BYTE 1
OPTION BYTE 2
DEFLECTION (PAL/NTSC)
480p OFFSET
1080i OFFSET
VGA OFFSET
VIDEO ADJUST1
VIDEO ADJUST2
VIDEO ADJUST3
VIDEO DJUST DNIe
VGA ADJUST
DTV ADJUST
Y.C-DELAY
EEPROM
RESET
Alignment and Adjustments
Samsung Electronics 1-13
Option byte 1
WIDE
Europe
Russian
On
Scart
On
off
CS
On
High
Off
Off
OSD Language
Off
Dynamic
On
Yes
Off
On
On
WIDE
Europe
English
On
Scart
On
On
CW
On
High
Off
Off
OSD Language
Off
Dynamic
On
Yes
Off
On
On
Item
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
OSD
CRT
Language Group
Language
ATM
Scart/RCA
Plug&Play
TeleWeb
CW/CS
LNA
HJack Ident
TOP TTX
High Deviation
TTX Group
Carrier Mute
P.Standard
Digital NR(Shipping conditions )
Speaker Include?
AGC
DNIe
DVR
Change mode
WIDE / 4:3
Europe / Asia
language table
On / Off
SCART / RCA
On / Off
On / Off
CS/CW
On / Off
High / Low
On / Off
On / Off
W-Europe(Refer to Table)
On / Off
Dynamic/Standard/Movie/Custom
On / Off
Yes/No
On/Off
On/Off
On/Off
❈ CRT : 1. 4 : 3 2. WIDE(16:9)
❈ Language Group : 1. Europe 2. Asia
❈ Europe Language Select
; Greece, Netherland, Germany, CIS, Rumania, Bulgaria, Sweden, Spain, Yougslavia, Italy, Czecho,
Croatia, Turkey, Portugal, Poland, France, Hungary, England
❈ Asia Language Select
; U.S.A, France, Malaysia, Indonesia, Arab, Persia
❈ ATM Select
ON : Greece, Netherland, Germany, CIS, Rumania, Bulgaria, Sweden, Spain, Yougslavia, Italy,
Czecho, Croatia, Turkey, Portugal, Poland, France, Hungary, England
OFF : Others Country
❈ TOP TTX Select
ON : Germany
OFF : Others Country
❈ TTX Group
; W-Europe, E-Europe, Russian, Arabic, Hebrew, OSD Language.
Initial value
CIS(32Z10) Europe(32z10)
Alignment and Adjustments
1-14 Samsung Electronics
Deflection Adjustment(PAL)
Initial value
26
24
41
18
10
6
1
0
27
23
34
34
31
28
40
232
97
Resister[HEX]
CXA2165 [16(7:2)]
CXA2165 [24(7:2)]
CXA2165 [19(7:2)]
CXA2165 [1E(7:2)]
CXA2165 [18(7:4)]
CXA2165 [25(7:4)]
CXA2165 [25(3:0)]
CXA2165 [18(3:0)]
CXA2165 [2A(3:0)]
CXA2165 [1B(7:4)]
CXA2165 [1C(7:4)]
CXA2165 [2D(7:2)]
CXA2165 [1F(7:4)]
CXA2165 [20(3:0)]
CXA2165 [17(7:2)]
Item
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
OSD
V Amp
V Shift
H EW
H Shift
V Linearity
Upper-Linearity
Lower-Linearity
V SC
H Parablar
Upper Corner
Lower Corner
H trapezium
Bow
Angle
V Position
CXA 2165 sub01
CXA 2165 sub02
Remark
Adjust
Adjust
Adjust
Adjust
FIX
FIX
FIX
FIX
Adjust
Adjust
Adjust
Adjust
Adjust
Adjust
FIX
FIX
FIX
Range
0~63
0~63
0~63
0~63
0~15
0~15
0~15
0~15
0~63
0~63
0~63
0~63
0~63
0~63
0~63
0~255
0~255
Deflection Adjustment(NTSC)
Initial value
2
-2
0
9
-4
-1
3
0
4
3
-1
2
0
0
0
232
97
Resister[HEX]
CXA2165 [16(7:2)]
CXA2165 [24(7:2)]
CXA2165 [19(7:2)]
CXA2165 [1E(7:2)]
CXA2165 [18(7:4)]
CXA2165 [25(7:4)]
CXA2165 [25(3:0)]
CXA2165 [18(3:0)]
CXA2165 [2A(3:0)]
CXA2165 [1B(7:4)]
CXA2165 [1C(7:4)]
CXA2165 [2D(7:2)]
CXA2165 [1F(7:4)]
CXA2165 [20(3:0)]
CXA2165 [17(7:2)]
Item
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
OSD
V Amp
V Shift
H EW
H Shift
V Linearity
Upper-Linearity
Lower-Linearity
V SC
H Parablar
Upper Corner
Lower Corner
H trapezium
Bow
Angle
V Position
CXA 2165 sub01
CXA 2165 sub02
Remark
Adjust
Adjust
Adjust
Adjust
FIX
FIX
FIX
FIX
Adjust
Adjust
Adjust
Adjust
Adjust
Adjust
FIX
FIX
FIX
Range
-63~63
-63~63
-63~63
-63~63
-15~15
-15~15
-15~15
-15~15
-63~63
-63~63
-63~63
-63~63
-63~63
-63~63
-63~63
0~255
0~255
Option byte 2
Initial value
On On
Off On
Change mode
ON/OFF(AV MODE NO SIGNAL)
ON/OFF
Item
00
02
Option byte 2
SAMSUNG LOGO
AUTO FORMAT
Alignment and Adjustments
Samsung Electronics 1-15
Deflection Normal(480p)
Initial value
0
4
3
-5
0
0
0
0
0
0
0
0
0
0
0
232
97
Resister[HEX]
CXA2165 [16(7:2)]
CXA2165 [24(7:2)]
CXA2165 [19(7:2)]
CXA2165 [1E(7:2)]
CXA2165 [18(7:4)]
CXA2165 [25(7:4)]
CXA2165 [25(3:0)]
CXA2165 [18(3:0)]
CXA2165 [2A(3:0)]
CXA2165 [1B(7:4)]
CXA2165 [1C(7:4)]
CXA2165 [2D(7:2)]
CXA2165 [1F(7:4)]
CXA2165 [20(3:0)]
CXA2165 [17(7:2)]
Item
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
OSD
V Amp
V Shift
H EW
H Shift
V Linearity
Upper-Linearity
Lower-Linearity
V SC
H Parablar
Upper Corner
Lower Corner
H trapezium
Bow
Angle
V Position
CXA 2165 sub01
CXA 2165 sub02
Remark
Adjust
Adjust
Adjust
Adjust
FIX
FIX
FIX
FIX
Adjust
Adjust
Adjust
Adjust
Adjust
Adjust
Adjust
FIX
FIX
Range
0~63
0~63
0~63
0~63
0~15
0~15
0~15
0~15
0~63
0~63
0~63
0~63
0~63
0~63
0~63
0~255
0~255
Deflection Normal(1080i)
Initial value
-13
-3
12
13
0
0
0
0
0
0
0
0
0
0
0
232
97
Resister[HEX]
CXA2165 [16(7:2)]
CXA2165 [24(7:2)]
CXA2165 [19(7:2)]
CXA2165 [1E(7:2)]
CXA2165 [18(7:4)]
CXA2165 [25(7:4)]
CXA2165 [25(3:0)]
CXA2165 [18(3:0)]
CXA2165 [2A(3:0)]
CXA2165 [1B(7:4)]
CXA2165 [1C(7:4)]
CXA2165 [2D(7:2)]
CXA2165 [1F(7:4)]
CXA2165 [20(3:0)]
CXA2165 [17(7:2)]
Item
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
OSD
V Amp
V Shift
H EW
H Shift
V Linearity
Upper-Linearity
Lower-Linearity
V SC
H Parablar
Upper Corner
Lower Corner
H trapezium
Bow
Angle
V Position
CXA 2165 sub01
CXA 2165 sub02
Remark
Adjust
Adjust
Adjust
Adjust
FIX
FIX
FIX
FIX
Adjust
Adjust
Adjust
Adjust
Adjust
Adjust
FIX
FIX
FIX
Range
0~63
0~63
0~63
0~63
0~15
0~15
0~15
0~15
0~63
0~63
0~63
0~63
0~63
0~63
0~63
0~255
0~255
Video Adjustment1
Initial value
34
32
32
1
32
32
40
32
36
34
6
15
28
1
1
2
10
Resister[HEX]
CXA2165 [0A(7:2)]
CXA2165 [0B7:2)]
CXA2165 [0C(7:2)]
CXA2165 [1E(7:4)]
CXA2165 [OF(7:2)]
CXA2165 [10(7:2)]
CXA2165 [06(7:2)]
CXA2165 [07(7:2)]
CXA2165 [08(7:2)]
CXA2165 [09(7:2)]
CXA2165 [0D(7:4)]
CXA2165 [03(7:2)]
CXA2165 [02(7:2)]
CXA2165 [03(1:0)]
CXA2165 [02(1:0)]
CXA2165 [05(1:0)]
CXA2165 [06(7:2)]
Item
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
OSD
R Cutoff
01 G Cutoff
B Cutoff
Color On/Off
CR Offset
CB Offset
R Drive
G Drive
B Drive
Sub Bright
Sub Contrast
Sub Color
Sub Tint(Hue)
CTI Level
Color AXIS
LTI Level
TTX BRT
Remark
Adjust
FIX
Adjust
FIX
FIX
FIX
Adjust
FIX
Adjust
Adjust
Adjust
FIX
FIX
FIX
FIX
FIX
FIX
Range
0~63
0~63
0~63
0~01
0~63
0~63
0~63
0~63
0~63
0~63
0~15
0~23(?)
0~63
0~03
0~03
0~03
0~63
Alignment and Adjustments
1-16 Samsung Electronics
VGE Defletion
Initial value
25
25
25
35
10
06
01
00
27
23
34
34
31
28
40
0
108
Resister[HEX]
CXA2165 [16(7:2)]
CXA2165 [17(7:2)]
CXA2165 [19(7:2)]
CXA2165 [1E(7:4)]
CXA2165 [18(7:2)]
CXA2165 [25(7:2)]
CXA2165 [25(7:2)]
CXA2165 [18(7:2)]
CXA2165 [1A(7:2)]
CXA2165 [1B(7:2)]
CXA2165 [1C(7:4)]
CXA2165 [1D(7:2)]
CXA2165 [1F(7:2)]
CXA2165 [20(1:0)]
CXA2165 [24(1:0)]
CXA2515 8C [01(7:0)]
CXA2515 8C [02(7:0)]
Item
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
OSD
Y Amp
Y Shift
H EW
H Shift
Y Linearity
Upper - Linearity
Lower - Linearity
Y SC
H Parablar
Upper Corner
Lower Corner
H Trapezium
Bow
Angle
Y Position
CXA 2165 sub01
CXA 2165 sub02
Remark
Adjust
Adjust
Adjust
Adjust
FIX
FIX
FIX
FIX
Adjust
Adjust
Adjust
Adjust
Adjust
Adjust
FIX
FIX
FIX
Range
0~63
0~63
0~63
0~63
0~15
0~15
0~15
0~15
0~63
0~63
0~63
0~63
0~63
0~63
0~63
0~255
0~255
Alignment and Adjustments
Samsung Electronics 1-17
Video Adjustment2
Initial value
3
2
2
2
14
1
2
2
2
3
1
0
8
13
0
17
32
35
32
35
Resister[HEX]
CXA2165 [07(1:0)]
CXA2165 [09(1:0)]
CXA2165 [0B(1:0)]
CXA2165 [0C(1:0)]
CXA2165 [OE(3:0)]
CXA2165 [11(3:2)]
CXA2165 [13(7:6)]
CXA2165 [13(5:4)]
CXA2165 [13(3:2)]
CXA2165 [13(1:0)]
CXA2165 [12(7:6)]
CXA2165 [11(1)]
CXA2165 [12(3:0)]
CXA2165 [14(7:4)]
VSP 9407[02(11:12)]
VSP 9407[25(14:10)]
VSP 9407[49(14:10)]
VSP 9407[4A(14:10)]
VSP 9407[49(14:10)]
VSP 9407[4A(14:10)
Item
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
OSD
ABL Mode
Gamma
DPIC Level
DC Trans
ABL-TH
VM-Level
VM-Coring
VM-f0
VM-Limit
VM-Delay
SHP CD
SHP f0
SHP f1&p/o
AKB Time
Coring
Peaking
Bandpass
Highpass
Bandpass
Highpass
Remark
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
Range
0~03
0~03
0~03
0~03
0~15
0~03
0~03
0~03
0~03
0~03
0~03
0~01
0~15
0~31(?)
0~01
0~31
0~127
0~127
0~127
0~127
Video Adjustment3
Initial value
8
5
0
0
0
6
1
1
1
Resister[HEX]
CXA2165 [26(3:0)]
CXA2165 [26(7:4)]
CXA2165 [28(2:0)]
CXA2165 [29(2:0)]
CXA2165 [1E(0)]
VSP 9407
CXA2165 [1E(0)]
CXA2165 [1E(0)]
CXA2165 [1E(0)]
Item
00
01
02
03
04
05
06
07
08
OSD
H_EHT comp
V_EHT comp
PIN EHT comp
AFC EHT comp
sync phase
NR Value
Sync Phase(480)
Sync Phase(1080)
Sync Phase(VGA)
Remark
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
Range
0~15
0~15
0~07
0~07
0~1
0~09
0~1
0~1
0~1
Alignment and Adjustments
1-18 Samsung Electronics
Video Adjustment DNIe
Initial value
185
185
185
61
64
63
20
20
3
7
3
7
32
32
32
32
Resister[HEX]
AD9883 [08(7:0)]
AD9883 [09(7:0)]
AD9883 [0A(7:0)]
AD9883 [0B(7:1)]
AD9883 [0C(7:1)]
AD9883 [0D(7:1)]
AD9883 [05(7:0)]
AD9883 [06(7:0)]
AD9883 [05(7:0)]
AD9883 [06(7:0)]
AD9883 [05(7:0)]
AD9883 [06(7:0)]
AD9883 [05(7:0)]
AD9883 [06(7:0)]
AD9883 [05(7:0)]
AD9883 [06(7:0)]
Item
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
OSD
AD9883 R GAIN
AD9883 G GAIN
AD9883 B GAIN
AD9883 R OFFSET
AD9883 G OFFSET
AD9883 B OFFSET
AD9883_NORMAL_REG05
AD9883_NORMAL_REG06
AD9883_1080i_REG05
AD9883_1080i_REG06
AD9883_1080i_50_REG05
AD9883_1080i_60_REG06
AD9883_480P_50_REG05
AD9883_480P_60_REG06
AD9883_576P_50_REG05
AD9883_576P_60_REG06
Remark
FIX
FIX
FIX
Adjust
FIX
Adjust
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
Range
0~255
0~255
0~255
0~127
0~127
0~127
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
DNIe Enhancement Adjustment
Initial value
(DECIMAL)
0
8
36
74
196
45
45
48
16
46
46
0
192
CONTROL
REGISTER
R’311 LOW
R’316 LOW
R’317 LOW
R’2B0 HIGH
R’2B0 LOW
R’2B3 HIGH
R’2B3 LOW
R’293 HIGH
R’294 HIGH
R’331 HIGH
R’332 HIGH
R’330 HIGH
R’352 LOW
DETAIL
ENHANCE
CONTRAST
ENHANCE
NOISE
REDUCTION
BWS
CTE
FACTORY MODE NAME
SNI DETAIL ENHANCE CORING
SNI DETAIL ENHANCE NOISE DETECT GAIN
SNI DETAIL ENHANCE GAIN
SNI CONTRAST ENHANCE CUTOFF
SNI CONTRAST ENHANCE UPPER
SNI CONTRAST ENHANCE LOWER GAIN
SNI CONTRAST ENHANCE UPPER GAIN
SNI NOISE REDUCTION Y-GAINMAX
SNI NOISE REDUCTION Y-GAINMIN
SNI BLACK STRETCH GAIN
SNI WHITE STRETCH GAIN
SNI BLACK and WHITE STRETCH ON/OFF
SNI COLOR ENHANCE GAIN
Remark
LOW/HIGH same
value setting.
BIT[4,0]
RANGE
0~63
0~15
0~127
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~3
0~255
0 : BLACK/WHITE OFF, 1 : WHITE ON, 2 : BLACK ON, 3 : BLACK/WHITE ON
Alignment and Adjustments
Samsung Electronics 1-19
VGA Adjust
Initial value
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Resister[HEX]
CXA2165 [09(7:2)]
CXA2165 [0D(7:4)]
CXA2165 [03(7:2)]
CXA2165 [02(7:2)]
CXA2165 [02(1:0)]
CXA2165 [05(1:0)]
CXA2165 [11(3:2)]
CXA2165 [13(7:6)]
CXA2165 [13(5:4)]
CXA2165 [13(3:2)]
CXA2165 [13(1:0)]
CXA2165 [12(7:6)]
CXA2165 [11(1)]
CXA2165 [12(3:0)]
Item
00
01
02
03
04
05
06
07
08
09
10
11
12
13
OSD
Sub Bright
Sub Contrast
Sub Color
Sub Tint
Color AXIS
LTI Level
VM Level
VM Coring
VM f0
VM Limit
VM Delay
SHP CD
SHP f0
SHP f0 & p10
Remark
Adjust
Adjust
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
Range
0~63
0~15
0~23
0~63
0~03
0~03
0~03
0~03
0~03
0~03
0~03
0~03
0~01
0~15
DTV Adjust(1080i)
IInitial value
38
7
15
28
1
1
1
2
2
2
3
1
0
8
Resister[HEX]
CXA2165 [09(7:2)]
CXA2165 [0D(7:4)]
CXA2165 [03(7:2)]
CXA2165 [02(7:2)]
CXA2165 [02(1:0)]
CXA2165 [05(1:0)]
CXA2165 [11(3:2)]
CXA2165 [13(7:6)]
CXA2165 [13(5:4)]
CXA2165 [13(3:2)]
CXA2165 [13(1:0)]
CXA2165 [12(7:6)]
CXA2165 [11(1)]
CXA2165 [12(3:0)]
Item
00
01
02
03
04
05
06
07
08
09
10
11
12
13
OSD
Sub Bright
Sub Contrast
Sub Color
Sub Tint
Color AXIS
LTI Level
VM Level
VM Coring
VM f0
VM Limit
VM Delay
SHP CD
SHP f0
SHP f0 & p10
Remark
Adjust
Adjust
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
Range
0~63
0~15
0~23
0~63
0~03
0~03
0~03
0~03
0~03
0~03
0~03
0~03
0~01
0~15
Alignment and Adjustments
1-20 Samsung Electronics
YC Delay
Initial value
2
-5
4
4
-1
1
0
0
-6
-7
-9
0
-5
0
Resister[HEX]
VSP9407[6B(12:8)]
VSP9407[6B(12:8)]
VSP9407[6B(12:8)]
VSP9407[6B(12:8)]
VSP9407[6B(12:8)]
VSP9407[6B(12:8)]
VSP9407[6B(12:8)]
VSP9407[6B(12:8)]
VSP9407[07(12:8)]
VSP9407[07(12:8)]
VSP9407[07(12:8)]
VSP9407[07(12:8)]
VSP9407[07(12:8)]
VSP9407[6B(12:8)]
Item
00
01
02
03
04
05
06
07
08
09
10
11
12
13
OSD
P.YC(AV) DELAY
P.YC(AV) DELAY
P.YC(AV) DELAY
P.BG.YC DELAY
P.DK.YC DELAY
P.I.YC DELAY
P.60.YC DELAY
P.L.YC DELAY
S.BG.YC DELAY
S.DK.YC DELAYt
S.I.YC DELAY
S.L.YC DELAY
NT4.43.YC DELAY
N.M.YC DELAY
Remark
Adjust
Adjust
Adjust
FIX
Adjust
Adjust
Adjust
Adjust
Adjust
Adjust
Adjust
Adjust
FIX
FIX
Range
-16~15
-16~15
-16~15
-16~15
-16~15
-16~15
-16~15
-16~15
-16~15
-16~15
-16~15
-16~15
-16~15
-16~15
DTV Adjust(480p)
IInitial value
38
7
15
28
1
2
1
2
2
2
3
1
0
8
Resister[HEX]
CXA2165 [09(7:2)]
CXA2165 [0D(7:4)]
CXA2165 [03(7:2)]
CXA2165 [02(7:2)]
CXA2165 [02(1:0)]
CXA2165 [05(1:0)]
CXA2165 [11(3:2)]
CXA2165 [13(7:6)]
CXA2165 [13(5:4)]
CXA2165 [13(3:2)]
CXA2165 [13(1:0)]
CXA2165 [12(7:6)]
CXA2165 [11(1)]
CXA2165 [12(3:0)]
Item
00
01
02
03
04
05
06
07
08
09
10
11
12
13
OSD
Sub Bright
Sub Contrast
Sub Color
Sub Tint
Color AXIS
LTI Level
VM Level
VM Coring
VM f0
VM Limit
VM Delay
SHP CD
SHP f0
SHP f0 & p10
Remark
Adjust
Adjust
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
Range
0~63
0~15
0~23
0~63
0~03
0~03
0~03
0~03
0~03
0~03
0~03
0~03
0~01
0~15
Alignment and Adjustments
Samsung Electronics 1-21
EEPROM
IInitial value
0
0
1
2
5
7
50
50
50
90
60
50
50
50
50
70
50
50
50
50
45
40
40
50
3
190
1
2
195
63
0
177
150
248
113
102
8
101
255
Resister[HEX]
CXA2165 [1B(1:0)]
CXA2165 [1C(1:0)]
CXA2165 [0A(1:0)]
CXA2165
CXA2165
CXA2165
CXA2165
CXA2165 [09(7:2)]
CXA2165 [03(7:2)]
CXA2165 [0D(7:4)]
CXA2165 [05(7:4)]
CXA2165 [02(7:4)]
CXA2165
CXA2165 [09(7:2)]
CXA2165 [03(7:2)]
CXA2165 [0D(7:4)]
CXA2165 [05(7:4)]
CXA2165 [02(7:4)]
CXA2165
CXA2165 [09(7:2)]
CXA2165 [03(7:2)]
CXA2165 [0D(7:4)]
CXA2165 [05(7:4)]
CXA2165 [02(7:4)]
CXA2165
CXA2165
CXA2165
CXA2165 [0A(1:0)]
CXA2165 [21(7:2)]
CXA2165 [22(7:2)]
CXA2165 [09(7:2)]
CXA2165 [0D(7:4)]
VSP9407[A7(16:10)]
VSP9407 [0D(9:0)]
VSP9407
VSP9407
VSP9407
VSP9407
VSP9407 [1E(15:12)]
Item
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
OSD
UP-UCG(up corner semi control)
LO-UCG(low corner semi control)
LTI MODE
System
50 hz Progressive Trepezium
100 hz Progressive Trepezium
Dynamic ColorTone
Dynamic Brightness
Dynamic Color
Dynamic Contrast
Dynamic Sharpness
Dynamic Tint
Standard ColorTone
Standard Brightness
Standard Color
Standard Contrast
Standard Sharpness
Standard Tint
Movie ColorTone
Movie Brightness
Movie Color
Movie Contrast
Movie Sharpness
Movie Tint
PROGRESSIVE TTX V-POSITION
PROGRESSIVE TTX H-POSITION
System(VGA)
LTI Mode(VGA)
Left Blanking(VGA)
Right Blanking(VGA)
Brightness(RGB)
Contrast(RGB)
U Saturation(RGB)
V saturation(RGB)
9407 Y Gain
9407 U Gain
Luminance Delay(Fix)
9407 V Gain
Start Value of Lum LUT(Main)-NR_ON
Remark
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
93 : Europe
82 : Europe
FIX
81 : Europe
FIX
Range
-2~2
-2~2
Alignment and Adjustments
1-22 Samsung Electronics
IInitial value
102
255
102
28
28
28
28
187
173
0
48
255
255
255
255
3
7
5
215
169
141
109
0
0
0
0
0
0
38
190
4
0
0
190
135
150
242
120
Resister[HEX]
VSP9407
VSP9407 [80(15:12)]
VSP9407
VSP9407
VSP9407
VSP9407 [2B(9:12)]
VSP9407
CXA2165 [21(7:2)]
CXA2165 [22(7:2)]
CXA2165 [04(1:0)]
CXA2165 [0E(7:4)]
VSP9407
VSP9407 [1E(15:12)]
VSP9407
VSP9407 [80(15:12)]
VSP9407
CXA2165 [0D(3:0)]
CXA2165 [0D(3:0)]
CXA2165 [21(7:2)]
CXA2165 [22(7:2)]
CXA2165 [21(7:2)]
CXA2165 [22(7:2)]
VSP9407
VSP9407
VSP9407
VSP9407
CXA2165 [0A(1:0)]
CXA2165 [0A(1:0)]
CXA2165
CXA2165
VSP9407
VSP9407
CXA2165
CXA2165 [09(7:2)]
CXA2165 [0D(7:4)]
VSP9407 [A7(16:10)]
VSP9407 [0D(9:0)]
DSP56367
Item
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
OSD
Noise Reduction(Main)-NR_ON
Start Value of Lum LUT(PIP)-NR_ON
Noise Reduction(PIP)-NR_ON
GMD Hysteresis
SECAM Color Sensitivity(Main)
FMD Thre
SECAM Color Sensitivity(PIP)
Left Blanking
Right Blanking
S-ABL
P-ABL
Start Value of Lum LUT(Main)-NR_OFF
Noise Reduction(Main)-NR_OFF
Start Value of Lum LUT(PIP)-NR_OFF
Noise Reduction(PIP)-NR_OFF
Picture Limit Level
OSD LEVEL(LRGB2_LEV)
TX LEVEL(LRGB2_LEV)
Left Blanking (480p)
Right Blanking (480p)
Left Blanking (1080i)
Right Blanking (1080i)
System (480p)
System (1080i)
CrCb Gain (480p)
CrCb Gain (1080i)
LTI Mode (480p)
LTI Mode (1080i)
TTX V Position
TTX H Position
16 PIP UPPER CORNER OFF SET
16 PIP LOWER CORNER OFF SET
4:3 Normal Parabola
Brightness(DVD)
Contrast(DVD)
U Saturation(DVD)
V saturation(DVD)
SW Filter size
Remark
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
Range
60~220
Alignment and Adjustments
Samsung Electronics 1-23
1-5 Speed, Aging mode & Reset mode
1. 3-Speed
1) Speed up Analog Conrtol three times and Time Speed sixty times to let line productivity be
improved Analog Control.
2) Enter
- Display + 3Speed Key
3) Cancel
- The 3-Speed mode is cancelled in Master Power Off
- Press the 3Speed Key
4) OSD : The message “3-SPEED” appears on the center of screen
5) No Signal : No AUTO OFF
2. Aging Mode
1) Enter : DISPLAY KEY -> FACTORY KEY (FACTORY MODE)
-> FACTORY KEY (AGING MODE)
- When the AGING mode is entered, the OSD’s are displayed at 100% SIZE WHITE.
- Mute SOUND
2) Cancel
- FACTORY remote conrtol -> Press the FACTORY Key
- LOCAL KEY -> Use the Key MATRIX (Panel Key)
- The AGING mode remains even in MASTER S/W OFF -> ON
Cancel the AGING mode only in the above two cases.
3. Factory Reset
1) Run “Reset” on the Factory Menu.
2) Initialize the other user control data except the items that are adjusted in the Factory Mode.
3) Power Off in standby mode.
1. Bus Stop Mode (Use a Micom Stop Pin)
1) Enter the Bus Stop Mode within 200ms when 12c Stop Port is acknowledaged “LOW”.
2) Settings when entering.
- Set the screen mode “STANDARD”.
- Set Bus Line Free.
- Cancal the Bus Stop Mode when 12c Stop Port is acknowledged “High”.
3) Setting when cancelling
- Re-load data from EEPROM and then re-set the appropriate IC.
2. Remot Control Adjustment Mode (Factory Auto Adjustment)
1) Enter the Remote Control Adjustment Mode when the remote control auto adjustment code is input.
2) Settings when entering.
- Set the screen mode “STANDARD”
- Set Bus Line Free.
3) Cancel the Remote Control Adjustment Mode when the usual key code is input.
4) When the code is input, write data in both EEPROM and the appropriate IC within 20ms.
Interval between Code Inputs : 30ms
1-5-1 3-Speed
1-5-2 Bus Stop Mode & Remote Control Adjustment
Alignment and Adjustments
1-24 Samsung Electronics
1-6 INITIALIZATION DATA DURING RESET
Item
Volume
Balance
Main,Pip Channel
Picture Standard
Sound Standard
Scan mode
Add/erase
Channel Sort
LNA
Color System
PIP Position
Fine Tune
Language
Pip,Main Source
Digital N/R
TILT
P-Size
PIP-Size
TTX Contrast
Child lock
Plug & Play
TeleWeb
TV Power
Blue Screen
TINT
Still Picture
AV Setup
Intialization Data
10 Step
Center
P01
Custom
(Set Value:Standard)
Nautral
All Channel erased
Erased
All Channel Off
Auto
Right under
Erased
Option byte Selection
RF
Option byte Selection
Center
Wide:auto,4:3:Normal
Big
Factory value
All Channel off
Option byte Selection
Turn on the menu when the
option byte is on.
Turn off the menu when the
option byte is off.
Stand by
On
Center
Cancellation
Ext2, Ext3 : RF
Item
Time
On/Off Time
H/P Volume
H/P Bal.,Tbl,Bass
Programe naming
TTX Source selection
Provider select
Power off after download
Boockmark list
Zoom Lift
Country
Dynamic range
Audio out
Int. mute
External audio
Pro Logic
Test Tone
Initialization Data
- - : - -
- - : - 10 Step
Center
All Channel Erased(*)
Center
Main
Erased
Yes
Erased
Center
Austria
On
Volume out
Off
Analog
Auto
Off
Small
Large
On
Large
0dB
0dB
0dB
3
15
Select Reset in the Factory Menu.
Initiate items not adjusted in the Factory mode (User Control Data) and turn off the power switch.
Speaker
Setting
Size
Speaker
Setting
Level
Speaker
Time delay
Main
Center
Woofer
Surround
Center
Woofer
Surround
Center
Surround
Alignment and Adjustments
Samsung Electronics 1-25
1-7 CHASSIS FUNTION
P
I
C
T
U
R
E
PIP
FUNTION
LINE FLICKERLESS
LARGE AREA FLICKERLESS
MOTION DETECTOR
MAIN STILL PICTURE
ZOOM FUNCTION(4:3)
WIDE CRT OPTION
ZOOM LIFT
DIGITAL N/R
COMB FILTER
CTI
SCAN MODE
P-STD
DYNAMIC-FOCUS
VM
TILT CONTROL
VGA
DVD
DNIe
DVR
MULTI PIP
LNA ON/OFF
SWAP,ROTATE,SIZE,SCAN
PAL
YES
YES
YES
YES
NORMAL -> ZOOM1-> ZOOM2 -> WIDE
AUTO WIDE->WIDE->PANORAMA->ZOOM1->ZOOM2->4:3
YES
YES
4H
DIGITAL CTI
NATURAL SCAN -> DIGITAL SCAN -> PORGRESSIVE SCAN
DYNAMIC->STANDARD->MOVIE->CUSTOM
YES
YES
YES
YES
RCA JACK MODEL ONLY -> YUV MODE
YES
YES
YES
YES
YES
Loading...